We currently allocate redistributor region structures for
individual redistributors when ACPI doesn't present us with
compact MMIO regions covering multiple redistributors.
It turns out that we allocate these structures even when
the redistributor is flagged as disabled by ACPI. It works
fine until someone actually tries to tarse one of these
structures, and access the corresponding MMIO region.
Instead, track the number of enabled redistributors, and
only allocate what is required. This makes sure that there
is no invalid data to misuse.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reported-by: Heyi Guo <guoheyi@huawei.com>
Tested-by: Heyi Guo <guoheyi@huawei.com>
Link: https://lore.kernel.org/r/20191216062745.63397-1-guoheyi@huawei.com
While GICv4.0 mandates 16 bit worth of VPEIDs, GICv4.1 allows smaller
implementations to be built. Add the required glue to dynamically
compute the limit.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20191224111055.11836-3-maz@kernel.org
GICv4.1 supports the RVPEID ("Residency per vPE ID"), which allows for
a much efficient way of making virtual CPUs resident (to allow direct
injection of interrupts).
The functionnality needs to be discovered on each and every redistributor
in the system, and disabled if the settings are inconsistent.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20191224111055.11836-2-maz@kernel.org
Pull irq updates from Ingo Molnar:
"Most of the IRQ subsystem changes in this cycle were irq-chip driver
updates:
- Qualcomm PDC wakeup interrupt support
- Layerscape external IRQ support
- Broadcom bcm7038 PM and wakeup support
- Ingenic driver cleanup and modernization
- GICv3 ITS preparation for GICv4.1 updates
- GICv4 fixes
There's also the series from Frederic Weisbecker that fixes memory
ordering bugs for the irq-work logic, whose primary fix is to turn
work->irq_work.flags into an atomic variable and then convert the
complex (and buggy) atomic_cmpxchg() loop in irq_work_claim() into a
much simpler atomic_fetch_or() call.
There are also various smaller cleanups"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
pinctrl/sdm845: Add PDC wakeup interrupt map for GPIOs
pinctrl/msm: Setup GPIO chip in hierarchy
irqchip/qcom-pdc: Add irqchip set/get state calls
irqchip/qcom-pdc: Add irqdomain for wakeup capable GPIOs
irqchip/qcom-pdc: Do not toggle IRQ_ENABLE during mask/unmask
irqchip/qcom-pdc: Update max PDC interrupts
of/irq: Document properties for wakeup interrupt parent
genirq: Introduce irq_chip_get/set_parent_state calls
irqdomain: Add bus token DOMAIN_BUS_WAKEUP
genirq: Fix function documentation of __irq_alloc_descs()
irq_work: Fix IRQ_WORK_BUSY bit clearing
irqchip/ti-sci-inta: Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(...))
irq_work: Slightly simplify IRQ_WORK_PENDING clearing
irq_work: Fix irq_work_claim() memory ordering
irq_work: Convert flags to atomic_t
irqchip: Ingenic: Add process for more than one irq at the same time.
irqchip: ingenic: Alloc generic chips from IRQ domain
irqchip: ingenic: Get virq number from IRQ domain
irqchip: ingenic: Error out if IRQ domain creation failed
irqchip: ingenic: Drop redundant irq_suspend / irq_resume functions
...
- On ARMv8 CPUs without hardware updates of the access flag, avoid
failing cow_user_page() on PFN mappings if the pte is old. The patches
introduce an arch_faults_on_old_pte() macro, defined as false on x86.
When true, cow_user_page() makes the pte young before attempting
__copy_from_user_inatomic().
- Covert the synchronous exception handling paths in
arch/arm64/kernel/entry.S to C.
- FTRACE_WITH_REGS support for arm64.
- ZONE_DMA re-introduced on arm64 to support Raspberry Pi 4
- Several kselftest cases specific to arm64, together with a MAINTAINERS
update for these files (moved to the ARM64 PORT entry).
- Workaround for a Neoverse-N1 erratum where the CPU may fetch stale
instructions under certain conditions.
- Workaround for Cortex-A57 and A72 errata where the CPU may
speculatively execute an AT instruction and associate a VMID with the
wrong guest page tables (corrupting the TLB).
- Perf updates for arm64: additional PMU topologies on HiSilicon
platforms, support for CCN-512 interconnect, AXI ID filtering in the
IMX8 DDR PMU, support for the CCPI2 uncore PMU in ThunderX2.
- GICv3 optimisation to avoid a heavy barrier when accessing the
ICC_PMR_EL1 register.
- ELF HWCAP documentation updates and clean-up.
- SMC calling convention conduit code clean-up.
- KASLR diagnostics printed during boot
- NVIDIA Carmel CPU added to the KPTI whitelist
- Some arm64 mm clean-ups: use generic free_initrd_mem(), remove stale
macro, simplify calculation in __create_pgd_mapping(), typos.
- Kconfig clean-ups: CMDLINE_FORCE to depend on CMDLINE, choice for
endinanness to help with allmodconfig.
-----BEGIN PGP SIGNATURE-----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=TPL9
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
"Apart from the arm64-specific bits (core arch and perf, new arm64
selftests), it touches the generic cow_user_page() (reviewed by
Kirill) together with a macro for x86 to preserve the existing
behaviour on this architecture.
Summary:
- On ARMv8 CPUs without hardware updates of the access flag, avoid
failing cow_user_page() on PFN mappings if the pte is old. The
patches introduce an arch_faults_on_old_pte() macro, defined as
false on x86. When true, cow_user_page() makes the pte young before
attempting __copy_from_user_inatomic().
- Covert the synchronous exception handling paths in
arch/arm64/kernel/entry.S to C.
- FTRACE_WITH_REGS support for arm64.
- ZONE_DMA re-introduced on arm64 to support Raspberry Pi 4
- Several kselftest cases specific to arm64, together with a
MAINTAINERS update for these files (moved to the ARM64 PORT entry).
- Workaround for a Neoverse-N1 erratum where the CPU may fetch stale
instructions under certain conditions.
- Workaround for Cortex-A57 and A72 errata where the CPU may
speculatively execute an AT instruction and associate a VMID with
the wrong guest page tables (corrupting the TLB).
- Perf updates for arm64: additional PMU topologies on HiSilicon
platforms, support for CCN-512 interconnect, AXI ID filtering in
the IMX8 DDR PMU, support for the CCPI2 uncore PMU in ThunderX2.
- GICv3 optimisation to avoid a heavy barrier when accessing the
ICC_PMR_EL1 register.
- ELF HWCAP documentation updates and clean-up.
- SMC calling convention conduit code clean-up.
- KASLR diagnostics printed during boot
- NVIDIA Carmel CPU added to the KPTI whitelist
- Some arm64 mm clean-ups: use generic free_initrd_mem(), remove
stale macro, simplify calculation in __create_pgd_mapping(), typos.
- Kconfig clean-ups: CMDLINE_FORCE to depend on CMDLINE, choice for
endinanness to help with allmodconfig"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (93 commits)
arm64: Kconfig: add a choice for endianness
kselftest: arm64: fix spelling mistake "contiguos" -> "contiguous"
arm64: Kconfig: make CMDLINE_FORCE depend on CMDLINE
MAINTAINERS: Add arm64 selftests to the ARM64 PORT entry
arm64: kaslr: Check command line before looking for a seed
arm64: kaslr: Announce KASLR status on boot
kselftest: arm64: fake_sigreturn_misaligned_sp
kselftest: arm64: fake_sigreturn_bad_size
kselftest: arm64: fake_sigreturn_duplicated_fpsimd
kselftest: arm64: fake_sigreturn_missing_fpsimd
kselftest: arm64: fake_sigreturn_bad_size_for_magic0
kselftest: arm64: fake_sigreturn_bad_magic
kselftest: arm64: add helper get_current_context
kselftest: arm64: extend test_init functionalities
kselftest: arm64: mangle_pstate_invalid_mode_el[123][ht]
kselftest: arm64: mangle_pstate_invalid_daif_bits
kselftest: arm64: mangle_pstate_invalid_compat_toggle and common utils
kselftest: arm64: extend toplevel skeleton Makefile
drivers/perf: hisi: update the sccl_id/ccl_id for certain HiSilicon platform
arm64: mm: reserve CMA and crashkernel in ZONE_DMA32
...
The GICv3 architecture specification is incredibly misleading when it
comes to PMR and the requirement for a DSB. It turns out that this DSB
is only required if the CPU interface sends an Upstream Control
message to the redistributor in order to update the RD's view of PMR.
This message is only sent when ICC_CTLR_EL1.PMHE is set, which isn't
the case in Linux. It can still be set from EL3, so some special care
is required. But the upshot is that in the (hopefuly large) majority
of the cases, we can drop the DSB altogether.
This relies on a new static key being set if the boot CPU has PMHE
set. The drawback is that this static key has to be exported to
modules.
Cc: Will Deacon <will@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Julien Thierry <julien.thierry.kdev@gmail.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
As per GIC spec, ITLinesNumber indicates the maximum SPI INTID that
the GIC implementation supports. And the maximum SPI INTID an
implementation might support is 1019 (field value 11111).
max(GICD_TYPER_SPIS(...), 1020) is not what we actually want for
GIC_LINE_NR. Fix it to min(GICD_TYPER_SPIS(...), 1020).
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1568789850-14080-1-git-send-email-yuzenghui@huawei.com
It looks like the HIP06/07 SoCs have extra bits in their GICD_TYPER
registers, which confuse the GICv3.1 code (these systems appear to
expose ESPIs while they actually don't).
Detect these systems as early as possible and wipe the fields that
should be RES0 in the register.
Tested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
As is it usual for the GIC, it isn't disallowed to put together a system
that is majorly inconsistent, with a distributor supporting the
extended ranges while some of the CPUs don't.
Kindly tell the user that things are sailing isn't going to be smooth.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Expand the pre-existing PPI support to be able to deal with the
Extended PPI range (EPPI). This includes obtaining the number of PPIs
from each individual redistributor, and compute the minimum set
(just in case someone builds something really clever...).
Signed-off-by: Marc Zyngier <maz@kernel.org>
Again, PPIs are becoming a variable set. Let's hack the PPI partition
code to make the top-level array dynamically allocated.
Signed-off-by: Marc Zyngier <maz@kernel.org>
As we're about to have a variable number of PPIs, let's make the
allocation of the NMI refcounts dynamic. Also apply some minor
cleanups (moving things around).
Signed-off-by: Marc Zyngier <maz@kernel.org>
GICv3.1 allows up to 80 PPIs (16 legaci PPIs and 64 Extended PPIs),
meaning we can't just leave the old 16 hardcoded everywhere.
We also need to add the infrastructure to discover the number of PPIs
on a per redistributor basis, although we still pretend there is only
16 of them for now.
No functional change.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Add the required support for the ESPI range, which behave exactly like
the SPIs of old, only with new funky INTIDs.
Signed-off-by: Marc Zyngier <maz@kernel.org>
In the beginning, life was simple. The GIC driver mostly cared about
PPIs, SPIs and LPIs, all with nicely layed out ranges.
We're about to change all that, with new ranges such as EPPI and ESPI
interleaved in the middle of the no-irq-land between the "special IDs"
and the LPI range. Boo.
In order to make our life less hellish, let's introduce a set of primitives
that will allow ranges to be identified easily and offsets to be remapped.
So far, there is no functionnal change.
Signed-off-by: Marc Zyngier <maz@kernel.org>
gic_configure_irq is currently passed the (re)distributor address,
to which it applies an a fixed offset to get to the configuration
registers. This offset is constant across all GICs, or rather it was
until to v3.1...
An easy way out is for the individual drivers to pass the base
address of the configuration register for the considered interrupt.
At the same time, move part of the error handling back to the
individual drivers, as things are about to change on that front.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Do not expose the distributor's VA (it appears in debugfs). Instead,
record the PA, which at least can be used to precisely identify
the associated irqchip and domain.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
- Fix a couple of UAF on error paths (RZA1, GICv3 ITS)
- Fix iMX GPCv2 trigger setting
- Add missing of_node_put on error path in MBIGEN
- Add another bunch of /* fall-through */ to silence warnings
-----BEGIN PGP SIGNATURE-----
iQJDBAABCgAtFiEEn9UcU+C1Yxj9lZw9I9DQutE9ekMFAl1B0ysPHG1hekBrZXJu
ZWwub3JnAAoJECPQ0LrRPXpDEq0P/19TlvVhBzRBQ7xrZsh7RYGYddgHZeYxEwcJ
iZaZnEwYPqrQXS7UIOyMmpdhDOE89sntgCfQWWhPqZdVMAPPAanucbcIA9vNxy+U
OI9ue90Eeo5MAm7T2qp3MgEROQ21npYeTNGPHM6Rhh3twbsLX5S7rQCOZBeuY1zT
l9FGOUsUgYfUgdEGAv4wZLdIakfTbwAlk+9QaryEn7leu4s/vzHIdyMmJ/RDlt/i
YPWFD4XfDV8WSE0CE88oy1T4ppD8e71C6LjS+NfJsY5brUGPDvcbllCm3tFudy/9
D/4kM6yjpNIGZK23p5ux8dBTZB/9+z/PadFJc6J78cFH+IMf2Clv40GrZ50cG8MK
GIDBgwGmooUU+vsmTTPeqtEn30CIyVGb1AkoZnTR/vRltsg0zaLhuqIHnhLTo5av
dEeTv1sBOcPR3b4NkX4WAHd5UJrF/a3/fSdW9h95rF/xlP3fto5lhRmtI9UOqlra
1X+GJXRWoEbMvLP75PlSOQkDiG8zKko9/5JX/da5Q0Qztl/gZPFaGexL/c36DLoJ
kKuHut/1TXu3xfoGPotYm8mainSHkEF1OThCOWX6sjS4m9JMYZMejjg9l1pNXfKw
lZVKKygYOwOeBubsYqmVOEliFai2EggSWmq77csu5FP84M/8JNRX+69yQLO0Cwea
ukYEvrvA
=oXHS
-----END PGP SIGNATURE-----
Merge tag 'irqchip-fixes-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip fixes from Marc Zyngier:
A small bunch of fixes from the irqchip department:
- Fix a couple of UAF on error paths (RZA1, GICv3 ITS)
- Fix iMX GPCv2 trigger setting
- Add missing of_node_put on error path in MBIGEN
- Add another bunch of /* fall-through */ to silence warnings
When fall-through warnings was enabled by default the following warning
was starting to show up:
In file included from ../arch/arm64/include/asm/cputype.h:132,
from ../arch/arm64/include/asm/cache.h:8,
from ../include/linux/cache.h:6,
from ../include/linux/printk.h:9,
from ../include/linux/kernel.h:15,
from ../include/linux/list.h:9,
from ../include/linux/kobject.h:19,
from ../include/linux/of.h:17,
from ../include/linux/irqdomain.h:35,
from ../include/linux/acpi.h:13,
from ../drivers/irqchip/irq-gic-v3.c:9:
../drivers/irqchip/irq-gic-v3.c: In function ‘gic_cpu_sys_reg_init’:
../arch/arm64/include/asm/sysreg.h:853:2: warning: this statement may fall
through [-Wimplicit-fallthrough=]
asm volatile(__msr_s(r, "%x0") : : "rZ" (__val)); \
^~~
../arch/arm64/include/asm/arch_gicv3.h:20:29: note: in expansion of macro ‘write_sysreg_s’
#define write_gicreg(v, r) write_sysreg_s(v, SYS_ ## r)
^~~~~~~~~~~~~~
../drivers/irqchip/irq-gic-v3.c:773:4: note: in expansion of macro ‘write_gicreg’
write_gicreg(0, ICC_AP0R2_EL1);
^~~~~~~~~~~~
../drivers/irqchip/irq-gic-v3.c:774:3: note: here
case 6:
^~~~
Rework so that the compiler doesn't warn about fall-through.
Fixes: d93512ef0f0e ("Makefile: Globally enable fall-through warning")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Pull irq updates from Thomas Gleixner:
"The irq departement provides the usual mixed bag:
Core:
- Further improvements to the irq timings code which aims to predict
the next interrupt for power state selection to achieve better
latency/power balance
- Add interrupt statistics to the core NMI handlers
- The usual small fixes and cleanups
Drivers:
- Support for Renesas RZ/A1, Annapurna Labs FIC, Meson-G12A SoC and
Amazon Gravition AMR/GIC interrupt controllers.
- Rework of the Renesas INTC controller driver
- ACPI support for Socionext SoCs
- Enhancements to the CSKY interrupt controller
- The usual small fixes and cleanups"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (39 commits)
irq/irqdomain: Fix comment typo
genirq: Update irq stats from NMI handlers
irqchip/gic-pm: Remove PM_CLK dependency
irqchip/al-fic: Introduce Amazon's Annapurna Labs Fabric Interrupt Controller Driver
dt-bindings: interrupt-controller: Add Amazon's Annapurna Labs FIC
softirq: Use __this_cpu_write() in takeover_tasklets()
irqchip/mbigen: Stop printing kernel addresses
irqchip/gic: Add dependency for ARM_GIC_MAX_NR
genirq/affinity: Remove unused argument from [__]irq_build_affinity_masks()
genirq/timings: Add selftest for next event computation
genirq/timings: Add selftest for irqs circular buffer
genirq/timings: Add selftest for circular array
genirq/timings: Encapsulate storing function
genirq/timings: Encapsulate timings push
genirq/timings: Optimize the period detection speed
genirq/timings: Fix timings buffer inspection
genirq/timings: Fix next event index function
irqchip/qcom: Use struct_size() in devm_kzalloc()
irqchip/irq-csky-mpintc: Remove unnecessary loop in interrupt handler
dt-bindings: interrupt-controller: Update csky mpintc
...
- arm64 support for syscall emulation via PTRACE_SYSEMU{,_SINGLESTEP}
- Wire up VM_FLUSH_RESET_PERMS for arm64, allowing the core code to
manage the permissions of executable vmalloc regions more strictly
- Slight performance improvement by keeping softirqs enabled while
touching the FPSIMD/SVE state (kernel_neon_begin/end)
- Expose a couple of ARMv8.5 features to user (HWCAP): CondM (new XAFLAG
and AXFLAG instructions for floating point comparison flags
manipulation) and FRINT (rounding floating point numbers to integers)
- Re-instate ARM64_PSEUDO_NMI support which was previously marked as
BROKEN due to some bugs (now fixed)
- Improve parking of stopped CPUs and implement an arm64-specific
panic_smp_self_stop() to avoid warning on not being able to stop
secondary CPUs during panic
- perf: enable the ARM Statistical Profiling Extensions (SPE) on ACPI
platforms
- perf: DDR performance monitor support for iMX8QXP
- cache_line_size() can now be set from DT or ACPI/PPTT if provided to
cope with a system cache info not exposed via the CPUID registers
- Avoid warning on hardware cache line size greater than
ARCH_DMA_MINALIGN if the system is fully coherent
- arm64 do_page_fault() and hugetlb cleanups
- Refactor set_pte_at() to avoid redundant READ_ONCE(*ptep)
- Ignore ACPI 5.1 FADTs reported as 5.0 (infer from the 'arm_boot_flags'
introduced in 5.1)
- CONFIG_RANDOMIZE_BASE now enabled in defconfig
- Allow the selection of ARM64_MODULE_PLTS, currently only done via
RANDOMIZE_BASE (and an erratum workaround), allowing modules to spill
over into the vmalloc area
- Make ZONE_DMA32 configurable
-----BEGIN PGP SIGNATURE-----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=0TDT
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- arm64 support for syscall emulation via PTRACE_SYSEMU{,_SINGLESTEP}
- Wire up VM_FLUSH_RESET_PERMS for arm64, allowing the core code to
manage the permissions of executable vmalloc regions more strictly
- Slight performance improvement by keeping softirqs enabled while
touching the FPSIMD/SVE state (kernel_neon_begin/end)
- Expose a couple of ARMv8.5 features to user (HWCAP): CondM (new
XAFLAG and AXFLAG instructions for floating point comparison flags
manipulation) and FRINT (rounding floating point numbers to integers)
- Re-instate ARM64_PSEUDO_NMI support which was previously marked as
BROKEN due to some bugs (now fixed)
- Improve parking of stopped CPUs and implement an arm64-specific
panic_smp_self_stop() to avoid warning on not being able to stop
secondary CPUs during panic
- perf: enable the ARM Statistical Profiling Extensions (SPE) on ACPI
platforms
- perf: DDR performance monitor support for iMX8QXP
- cache_line_size() can now be set from DT or ACPI/PPTT if provided to
cope with a system cache info not exposed via the CPUID registers
- Avoid warning on hardware cache line size greater than
ARCH_DMA_MINALIGN if the system is fully coherent
- arm64 do_page_fault() and hugetlb cleanups
- Refactor set_pte_at() to avoid redundant READ_ONCE(*ptep)
- Ignore ACPI 5.1 FADTs reported as 5.0 (infer from the
'arm_boot_flags' introduced in 5.1)
- CONFIG_RANDOMIZE_BASE now enabled in defconfig
- Allow the selection of ARM64_MODULE_PLTS, currently only done via
RANDOMIZE_BASE (and an erratum workaround), allowing modules to spill
over into the vmalloc area
- Make ZONE_DMA32 configurable
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (54 commits)
perf: arm_spe: Enable ACPI/Platform automatic module loading
arm_pmu: acpi: spe: Add initial MADT/SPE probing
ACPI/PPTT: Add function to return ACPI 6.3 Identical tokens
ACPI/PPTT: Modify node flag detection to find last IDENTICAL
x86/entry: Simplify _TIF_SYSCALL_EMU handling
arm64: rename dump_instr as dump_kernel_instr
arm64/mm: Drop [PTE|PMD]_TYPE_FAULT
arm64: Implement panic_smp_self_stop()
arm64: Improve parking of stopped CPUs
arm64: Expose FRINT capabilities to userspace
arm64: Expose ARMv8.5 CondM capability to userspace
arm64: defconfig: enable CONFIG_RANDOMIZE_BASE
arm64: ARM64_MODULES_PLTS must depend on MODULES
arm64: bpf: do not allocate executable memory
arm64/kprobes: set VM_FLUSH_RESET_PERMS on kprobe instruction pages
arm64/mm: wire up CONFIG_ARCH_HAS_SET_DIRECT_MAP
arm64: module: create module allocations without exec permissions
arm64: Allow user selection of ARM64_MODULE_PLTS
acpi/arm64: ignore 5.1 FADTs that are reported as 5.0
arm64: Allow selecting Pseudo-NMI again
...
In the presence of any form of instrumentation, nmi_enter() should be
done before calling any traceable code and any instrumentation code.
Currently, nmi_enter() is done in handle_domain_nmi(), which is much
too late as instrumentation code might get called before. Move the
nmi_enter/exit() calls to the arch IRQ vector handler.
On arm64, it is not possible to know if the IRQ vector handler was
called because of an NMI before acknowledging the interrupt. However, It
is possible to know whether normal interrupts could be taken in the
interrupted context (i.e. if taking an NMI in that context could
introduce a potential race condition).
When interrupting a context with IRQs disabled, call nmi_enter() as soon
as possible. In contexts with IRQs enabled, defer this to the interrupt
controller, which is in a better position to know if an interrupt taken
is an NMI.
Fixes: bc3c03ccb4 ("arm64: Enable the support of pseudo-NMIs")
Cc: <stable@vger.kernel.org> # 5.1.x-
Cc: Will Deacon <will.deacon@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 503 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.811534538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for Amazon Graviton custom variant of GICv2m, where the message
is encoded using the MSI message address, as opposed to standard
GICv2m, where the SPI number is encoded in the MSI message data.
In addition, the Graviton flavor of GICv2m is used along GICv3 (and not
GICv2).
Co-developed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Zeev Zilberman <zeev@amazon.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Parsing entries in an ACPI table had assumed a generic header
structure. There is no standard ACPI header, though, so less common
layouts with different field sizes required custom parsers to go through
their subtable entry list.
Create the infrastructure for adding different table types so parsing
the entries array may be more reused for all ACPI system tables and
the common code doesn't need to be duplicated.
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Tested-by: Brice Goglin <Brice.Goglin@inria.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement NMI callbacks for GICv3 irqchip. Install NMI safe handlers
when setting up interrupt line as NMI.
Only SPIs and PPIs are allowed to be set up as NMI.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Provide a higher priority to be used for pseudo-NMIs. When such an
interrupt is received, keep interrupts fully disabled at CPU level to
prevent receiving other pseudo-NMIs while handling the current one.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The values non secure EL1 needs to use for PMR and RPR registers depends on
the value of SCR_EL3.FIQ.
The values non secure EL1 sees from the distributor and redistributor
depend on whether security is enabled for the GIC or not.
To avoid having to deal with two sets of values for PMR
masking/unmasking, only enable pseudo-NMIs when GIC has non-secure view
of priorities.
Also, add firmware requirements related to SCR_EL3.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Once the boot CPU has been prepared or a new secondary CPU has been
brought up, use ICC_PMR_EL1 to mask interrupts on that CPU and clear
PSR.I bit.
Since ICC_PMR_EL1 is initialized at CPU bringup, avoid overwriting
it in the GICv3 driver.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The code to detect whether Linux has access to group0 interrupts can
prove useful in other parts of the driver.
Provide a separate function to do this.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Mask the IRQ priority through PMR and re-enable IRQs at CPU level,
allowing only higher priority interrupts to be received during interrupt
handling.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Pull Devicetree updates from Rob Herring:
"The biggest highlight here is the start of using json-schema for DT
bindings. Being able to validate bindings has been discussed for years
with little progress.
- Initial support for DT bindings using json-schema language. This is
the start of converting DT bindings from free-form text to a
structured format.
- Reworking of initrd address initialization. This moves to using the
phys address instead of virt addr in the DT parsing code. This
rework was motivated by CONFIG_DEV_BLK_INITRD causing unnecessary
rebuilding of lots of files.
- Fix stale phandle entries in phandle cache
- DT overlay validation improvements. This exposed several memory
leak bugs which have been fixed.
- Use node name and device_type helper functions in DT code
- Last remaining conversions to using %pOFn printk specifier instead
of device_node.name directly
- Create new common RTC binding doc and move all trivial RTC devices
out of trivial-devices.txt.
- New bindings for Freescale MAG3110 magnetometer, Cadence Sierra
PHY, and Xen shared memory
- Update dtc to upstream version v1.4.7-57-gf267e674d145"
* tag 'devicetree-for-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (68 commits)
of: __of_detach_node() - remove node from phandle cache
of: of_node_get()/of_node_put() nodes held in phandle cache
gpio-omap.txt: add reg and interrupts properties
dt-bindings: mrvl,intc: fix a trivial typo
dt-bindings: iio: magnetometer: add dt-bindings for freescale mag3110
dt-bindings: Convert trivial-devices.txt to json-schema
dt-bindings: arm: mrvl: amend Browstone compatible string
dt-bindings: arm: Convert Tegra board/soc bindings to json-schema
dt-bindings: arm: Convert ZTE board/soc bindings to json-schema
dt-bindings: arm: Add missing Xilinx boards
dt-bindings: arm: Convert Xilinx board/soc bindings to json-schema
dt-bindings: arm: Convert VIA board/soc bindings to json-schema
dt-bindings: arm: Convert ST STi board/soc bindings to json-schema
dt-bindings: arm: Convert SPEAr board/soc bindings to json-schema
dt-bindings: arm: Convert CSR SiRF board/soc bindings to json-schema
dt-bindings: arm: Convert QCom board/soc bindings to json-schema
dt-bindings: arm: Convert TI nspire board/soc bindings to json-schema
dt-bindings: arm: Convert TI davinci board/soc bindings to json-schema
dt-bindings: arm: Convert Calxeda board/soc bindings to json-schema
dt-bindings: arm: Convert Altera board/soc bindings to json-schema
...
Access to GICR_WAKER is restricted on msm8996 SoC in Hypervisor.
Its been more than 2+ years of wait for this to be fixed, which has
no hopes to be fixed. This change was introduced for the "lead device"
on msm8996 platform. It looks like all publicly available msm8996 and
other Qualcomm SoCs have this implementation.
So add a quirk to not access this register on msm8996.
With this quirk MSM8996 can at least boot out of mainline,
which can help community to work with boards based on MSM8996 and other
SoCs with have this restrictions. This Quirk is based on device tree
compatible string.
Without this patch Qualcomm DB820c board reboots when GICR_WAKER
is accessed.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch adds support to device tree based quirks based on
device tree compatible string.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Multiple interrupts pending for a CPU is actually rare. Doing an
acknowledge loop does not give much better performance or even can
deteriorate them.
Do not loop when an interrupt has been acknowledged, just return
from interrupt and wait for another one to be raised.
Tested-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We currently initialize the LPIs (and the ITS) fairly early, even
before the SMP support and the CPU interface. This is a bit odd
(as LPIs are not exactly crutial for the early boot process),
and is going to cause issues when reorganizing the probing code.
Let's move this initialization later.
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Although GICv3 doesn't directly offers support for wake-up interrupts
and relies on external HW for this, it shouldn't prevent the driver
for such HW from doing it work.
Let's set the required flags on the irq_chip structures.
Reported-by: Lina Iyer <ilina@codeaurora.org>
Tested-by: Lina Iyer <ilina@codeaurora.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Instead of exposing the GIC distributor IntID field in the rdist
structure that is passed to the ITS, let's replace it with a
copy of the whole GICD_TYPER register. We are going to need
some of this information at a later time.
No functionnal change.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
GICv3 offers the possibility to signal SPIs using a pair of doorbells
(SETPI, CLRSPI) under the name of Message Based Interrupts (MBI).
They can be used as either traditional (edge) MSIs, or the more exotic
level-triggered flavour.
Let's implement support for platform MSI, which is the original intent
for this feature.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lkml.kernel.org/r/20180508121438.11301-8-marc.zyngier@arm.com
As we're about to introduce MSI domains based on top of the GICv3
domain, we must make sure nothing the new domains do not alias
with the core domain.
So let's tag that core domain with the DOMAIN_BUS_WIRED attribute,
ensuring it gets picked up by other drivers that use irq_find_host().
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lkml.kernel.org/r/20180508121438.11301-7-marc.zyngier@arm.com
No changes in semantics -- key init is true; replace
static_key_slow_dec with static_branch_disable
static_key_true with static_branch_likely
The first is because we never actually do any couterpart incs,
thus there is really no reference counting semantics going on.
Use the more proper static_branch_disable() construct.
Also added a '_key' suffix to supports_deactivate, for better
self documentation.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We would like to reset the Group-0 Active Priority Registers
at boot time if they are available to us. They would be available
if SCR_EL3.FIQ was not set, but we cannot directly probe this bit,
and short of checking, we may end-up trapping to EL3, and the
firmware may not be please to get such an exception. Yes, this
is dumb.
Instead, let's use PMR to find out if its value gets affected by
SCR_EL3.FIQ being set. We use the fact that when SCR_EL3.FIQ is
set, the LSB of the priority is lost due to the shifting back and
forth of the actual priority. If we read back a 0, we know that
Group0 is unavailable. In case we read a non-zero value, we can
safely reset the AP0Rn register.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Clearing AP0Rn has created a number of regressions, due to systems
that have SCR_EL3.FIQ set. Even when addressing some obvious bugs,
GIC500 platforms seem to act bizarrely (we are supposed to have
5 bits of priority, but PMR seems to behave as if we had 6...).
Drop the AP0Rn reset for the time being, it is unlikely to have any
effect if kexec-ing.
Fixes: d6062a6d62 irqchip/gic-v3: Reset APgRn registers at boot time
Reported-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We cannot know the trigger of partitionned PPIs ahead of time
(when we instanciate the partitions), so let's not check them
early.
Reported-by: JeffyChen <jeffy.chen@rock-chips.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There is a huge number of broken device trees out there. Just
grepping through the tree for the use of IRQ_TYPE_NONE in conjunction
with the GIC is scary.
People just don't realise that IRQ_TYPE_NONE just doesn't exist, and
you just get whatever junk was there before. So let's make them aware
of the issue.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
For most GICv3 implementations, enabling LPIs is a one way switch.
Once they're on, there is no turning back, which completely kills
kexec (pending tables will always be live, and we can't tell the
secondary kernel where they are).
This is really annoying if you plan to use Linux as a bootloader,
as it pretty much guarantees that the secondary kernel won't be
able to use MSIs, and may even see some memory corruption. Bad.
A workaround for this unfortunate situation is to allow the kernel
not to enable LPIs, even if the feature is present in the HW. This
would allow Linux-as-a-bootloader to leave LPIs alone, and let the
secondary kernel to do whatever it wants with them.
Let's introduce a boolean "irqchip.gicv3_nolpi" command line option
that serves that purpose.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Booting a crash kernel while in an interrupt handler is likely
to leave the Active Priority Registers with some state that
is not relevant to the new kernel, and is likely to lead
to erratic behaviours such as interrupts not firing as their
priority is already active.
As a sanity measure, wipe the APRs clean on startup. We make
sure to wipe both group 0 and 1 registers in order to avoid
any surprise.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Marc Zyngier