Commit Graph

900 Commits

Author SHA1 Message Date
Chris Chiu 0803d7befa tpm: self test failure should not cause suspend to fail
The Acer Acer Veriton X4110G has a TPM device detected as:
  tpm_tis 00:0b: 1.2 TPM (device-id 0xFE, rev-id 71)

After the first S3 suspend, the following error appears during resume:
  tpm tpm0: A TPM error(38) occurred continue selftest

Any following S3 suspend attempts will now fail with this error:
  tpm tpm0: Error (38) sending savestate before suspend
  PM: Device 00:0b failed to suspend: error 38

Error 38 is TPM_ERR_INVALID_POSTINIT which means the TPM is
not in the correct state. This indicates that the platform BIOS
is not sending the usual TPM_Startup command during S3 resume.
>From this point onwards, all TPM commands will fail.

The same issue was previously reported on Foxconn 6150BK8MC and
Sony Vaio TX3.

The platform behaviour seems broken here, but we should not break
suspend/resume because of this.

When the unexpected TPM state is encountered, set a flag to skip the
affected TPM_SaveState command on later suspends.

Cc: stable@vger.kernel.org
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Link: http://lkml.kernel.org/r/CAB4CAwfSCvj1cudi+MWaB5g2Z67d9DwY1o475YOZD64ma23UiQ@mail.gmail.com
Link: https://lkml.org/lkml/2011/3/28/192
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=591031
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2018-03-23 10:25:02 +02:00
Tomas Winkler 076d356460 tpm2: add longer timeouts for creation commands.
TPM2_CC_Create(0x153) and TPM2_CC_CreatePrimary (0x131) involve generation
of crypto keys which can be a computationally intensive task. The timeout
is set to 3min. Rather than increasing default timeout a new constant is
added, to not stall for too long on regular commands failures.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2018-03-23 10:18:06 +02:00
Tomas Winkler 09b17f321c tpm_crb: use __le64 annotated variable for response buffer address
use __le64 annotated variable for response buffer address as this is
read in little endian format form the register.

This suppresses sparse warning
drivers/char/tpm/tpm_crb.c:558:18: warning: cast to restricted __le64

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2018-03-23 10:18:06 +02:00
Winkler, Tomas 62c09e12bb tpm: fix buffer type in tpm_transmit_cmd
1. The buffer cannot be const as it is used both for send and receive.
2. Drop useless casting to u8 *, as this is already a
type of 'buf' parameter, it has just masked the 'const' issue.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2018-03-23 10:18:06 +02:00
Winkler, Tomas 65520d46a4 tpm: tpm-interface: fix tpm_transmit/_cmd kdoc
Fix tmp_ -> tpm_ typo and add reference to 'space' parameter
in kdoc for tpm_transmit and tpm_transmit_cmd functions.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2018-03-23 10:18:05 +02:00
Tomas Winkler 888d867df4 tpm: cmd_ready command can be issued only after granting locality
The correct sequence is to first request locality and only after
that perform cmd_ready handshake, otherwise the hardware will drop
the subsequent message as from the device point of view the cmd_ready
handshake wasn't performed. Symmetrically locality has to be relinquished
only after going idle handshake has completed, this requires that
go_idle has to poll for the completion and as well locality
relinquish has to poll for completion so it is not overridden
in back to back commands flow.

Two wrapper functions are added (request_locality relinquish_locality)
to simplify the error handling.

The issue is only visible on devices that support multiple localities.

Fixes: 877c57d0d0 ("tpm_crb: request and relinquish locality 0")
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
2018-03-23 10:18:05 +02:00
Jeremy Boone 3be2327475 tpm: fix potential buffer overruns caused by bit glitches on the bus
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips.  If a bit does
flip it could cause an overrun if it's in one of the size parameters,
so sanity check that we're not overrunning the provided buffer when
doing a memcpy().

Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
2018-02-26 15:43:46 -08:00
Jeremy Boone 6d24cd186d tpm: st33zp24: fix potential buffer overruns caused by bit glitches on the bus
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips.  In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data.  Also sanity check that the expected amount of data is
large enough for the TPM header.

Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
2018-02-26 15:43:45 -08:00
Jeremy Boone 9b8cb28d7c tpm_i2c_infineon: fix potential buffer overruns caused by bit glitches on the bus
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips.  In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data.  Also sanity check that the expected amount of data is
large enough for the TPM header.

Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
2018-02-26 15:43:44 -08:00
Jeremy Boone f9d4d9b5a5 tpm_i2c_nuvoton: fix potential buffer overruns caused by bit glitches on the bus
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips.  In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data.  Also sanity check that the expected amount of data is
large enough for the TPM header.

Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
2018-02-26 15:43:44 -08:00
Jeremy Boone 6bb320ca4a tpm_tis: fix potential buffer overruns caused by bit glitches on the bus
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips.  In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data.  Also sanity check that the expected amount of data is
large enough for the TPM header.

Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
2018-02-26 15:43:43 -08:00
Linus Torvalds a9a08845e9 vfs: do bulk POLL* -> EPOLL* replacement
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:

    for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
        L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
        for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
    done

with de-mangling cleanups yet to come.

NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do.  But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.

The next patch from Al will sort out the final differences, and we
should be all done.

Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-02-11 14:34:03 -08:00
Linus Torvalds ae0cb7be35 Merge branch 'next-tpm' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull tpm updates from James Morris:

 - reduce polling delays in tpm_tis

 - support retrieving TPM 2.0 Event Log through EFI before
   ExitBootServices

 - replace tpm-rng.c with a hwrng device managed by the driver for each
   TPM device

 - TPM resource manager synthesizes TPM_RC_COMMAND_CODE response instead
   of returning -EINVAL for unknown TPM commands. This makes user space
   more sound.

 - CLKRUN fixes:

    * Keep #CLKRUN disable through the entier TPM command/response flow

    * Check whether #CLKRUN is enabled before disabling and enabling it
      again because enabling it breaks PS/2 devices on a system where it
      is disabled

* 'next-tpm' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  tpm: remove unused variables
  tpm: remove unused data fields from I2C and OF device ID tables
  tpm: only attempt to disable the LPC CLKRUN if is already enabled
  tpm: follow coding style for variable declaration in tpm_tis_core_init()
  tpm: delete the TPM_TIS_CLK_ENABLE flag
  tpm: Update MAINTAINERS for Jason Gunthorpe
  tpm: Keep CLKRUN enabled throughout the duration of transmit_cmd()
  tpm_tis: Move ilb_base_addr to tpm_tis_data
  tpm2-cmd: allow more attempts for selftest execution
  tpm: return a TPM_RC_COMMAND_CODE response if command is not implemented
  tpm: Move Linux RNG connection to hwrng
  tpm: use struct tpm_chip for tpm_chip_find_get()
  tpm: parse TPM event logs based on EFI table
  efi: call get_event_log before ExitBootServices
  tpm: add event log format version
  tpm: rename event log provider files
  tpm: move tpm_eventlog.h outside of drivers folder
  tpm: use tpm_msleep() value as max delay
  tpm: reduce tpm polling delay in tpm_tis_core
  tpm: move wait_for_tpm_stat() to respective driver files
2018-01-31 13:12:31 -08:00
Arnd Bergmann 68021bf473 tpm: remove unused variables
The CLKRUN fix caused a few harmless compile-time warnings:

drivers/char/tpm/tpm_tis.c: In function 'tpm_tis_pnp_remove':
drivers/char/tpm/tpm_tis.c:274:23: error: unused variable 'priv' [-Werror=unused-variable]
drivers/char/tpm/tpm_tis.c: In function 'tpm_tis_plat_remove':
drivers/char/tpm/tpm_tis.c:324:23: error: unused variable 'priv' [-Werror=unused-variable]

This removes the variables that have now become unused.

Fixes: 6d0866cbc2d3 ("tpm: Keep CLKRUN enabled throughout the duration of transmit_cmd()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: James Morris <jmorris@namei.org>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2018-01-08 12:58:54 +02:00
Javier Martinez Canillas b4f20826de tpm: remove unused data fields from I2C and OF device ID tables
The data field for the entries in the device tables are set but not used.

Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Jason Gunthorpe <jgg@ziepe.ca>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2018-01-08 12:58:39 +02:00
Javier Martinez Canillas 6c9f0ce0df tpm: only attempt to disable the LPC CLKRUN if is already enabled
Commit 5e572cab92 ("tpm: Enable CLKRUN protocol for Braswell systems")
added logic in the TPM TIS driver to disable the Low Pin Count CLKRUN
signal during TPM transactions.

Unfortunately this breaks other devices that are attached to the LPC bus
like for example PS/2 mouse and keyboards.

One flaw with the logic is that it assumes that the CLKRUN is always
enabled, and so it unconditionally enables it after a TPM transaction.

But it could be that the CLKRUN# signal was already disabled in the LPC
bus and so after the driver probes, CLKRUN_EN will remain enabled which
may break other devices that are attached to the LPC bus but don't have
support for the CLKRUN protocol.

Fixes: 5e572cab92 ("tpm: Enable CLKRUN protocol for Braswell systems")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: James Ettle <james@ettle.org.uk>
Tested-by: Jeffery Miller <jmiller@neverware.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2018-01-08 12:58:39 +02:00
Javier Martinez Canillas 5fc0bead78 tpm: follow coding style for variable declaration in tpm_tis_core_init()
The coding style says "use just one data declaration per line (no commas
for multiple data declarations)" so follow this convention.

Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2018-01-08 12:58:39 +02:00
Javier Martinez Canillas 764325add6 tpm: delete the TPM_TIS_CLK_ENABLE flag
This flag is only used to warn if CLKRUN_EN wasn't disabled on Braswell
systems, but the only way this can happen is if the code is not correct.

So it's an unnecessary check that just makes the code harder to read.

Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2018-01-08 12:58:38 +02:00
Azhar Shaikh b3e958ce4c tpm: Keep CLKRUN enabled throughout the duration of transmit_cmd()
Commit 5e572cab92 ("tpm: Enable CLKRUN protocol for Braswell
systems") disabled CLKRUN protocol during TPM transactions and re-enabled
once the transaction is completed. But there were still some corner cases
observed where, reading of TPM header failed for savestate command
while going to suspend, which resulted in suspend failure.
To fix this issue keep the CLKRUN protocol disabled for the entire
duration of a single TPM command and not disabling and re-enabling
again for every TPM transaction. For the other TPM accesses outside
TPM command flow, add a higher level of disabling and re-enabling
the CLKRUN protocol, instead of doing for every TPM transaction.

Fixes: 5e572cab92 ("tpm: Enable CLKRUN protocol for Braswell systems")
Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Reviewed-by: Jarkko Sakkinen  <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen  <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen  <jarkko.sakkinen@linux.intel.com>
2018-01-08 12:58:38 +02:00
Azhar Shaikh c382babccb tpm_tis: Move ilb_base_addr to tpm_tis_data
Move static variable ilb_base_addr to tpm_tis_data.

Cc: stable@vger.kernel.org
Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Reviewed-by: Jarkko Sakkinen  <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen  <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen  <jarkko.sakkinen@linux.intel.com>
2018-01-08 12:58:37 +02:00
Alexander.Steffen@infineon.com 0b66f2a05a tpm2-cmd: allow more attempts for selftest execution
Previously, if the last attempt to execute the selftest command failed with
RC_TESTING, there was still a call to tpm_msleep, even though no further
attempt would be made. This causes an unnecessary delay, therefore ensure
that if the last attempt fails the function is left immediately.

Also, instead of ensuring that the cumulated runtime of all attempts is
larger than the command duration for TPM2_SelfTest, ensure that there is at
least one attempt for which the delay is larger than the expected command
duration. This allows slow TPMs to execute all their tests in the
background, without slowing down faster TPMs that have finished their tests
earlier. If tests are still not finished even with this long delay, then
something is broken and the TPM is not used.

Fixes: 125a221054 ("tpm: React correctly to RC_TESTING from TPM 2.0 self
tests")

Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2018-01-08 12:58:37 +02:00
Javier Martinez Canillas 095531f891 tpm: return a TPM_RC_COMMAND_CODE response if command is not implemented
According to the TPM Library Specification, a TPM device must do a command
header validation before processing and return a TPM_RC_COMMAND_CODE code
if the command is not implemented.

So user-space will expect to handle that response as an error. But if the
in-kernel resource manager is used (/dev/tpmrm?), an -EINVAL errno code is
returned instead if the command isn't implemented. This confuses userspace
since it doesn't expect that error value.

This also isn't consistent with the behavior when not using TPM spaces and
accessing the TPM directly (/dev/tpm?). In this case, the command is sent
to the TPM even when not implemented and the TPM responds with an error.

Instead of returning an -EINVAL errno code when the tpm_validate_command()
function fails, synthesize a TPM command response so user-space can get a
TPM_RC_COMMAND_CODE as expected when a chip doesn't implement the command.

The TPM only sets 12 of the 32 bits in the TPM_RC response, so the TSS and
TAB specifications define that higher layers in the stack should use some
of the unused 20 bits to specify from which level of the stack the error
is coming from.

Since the TPM_RC_COMMAND_CODE response code is sent by the kernel resource
manager, set the error level to the TAB/RM layer so user-space is aware of
this.

Suggested-by: Jason Gunthorpe <jgg@ziepe.ca>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: William Roberts <william.c.roberts@intel.com>
Reviewed-by: Philip Tricca <philip.b.tricca@intel.com>
Reviewed-by: Jarkko Sakkinen  <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen  <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen  <jarkko.sakkinen@linux.intel.com>
2018-01-08 12:58:36 +02:00
Jason Gunthorpe 6e592a065d tpm: Move Linux RNG connection to hwrng
The tpm-rng.c approach is completely inconsistent with how the kernel
handles hotplug. Instead manage a hwrng device for each TPM. This will
cause the kernel to read entropy from the TPM when it is plugged in, and
allow access to the TPM rng via /dev/hwrng.

Signed-off-by: Jason Gunthorpe <jgg@ziepe.ca>
Tested-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2018-01-08 12:58:36 +02:00
Jarkko Sakkinen aad887f664 tpm: use struct tpm_chip for tpm_chip_find_get()
Device number (the character device index) is not a stable identifier
for a TPM chip. That is the reason why every call site passes
TPM_ANY_NUM to tpm_chip_find_get().

This commit changes the API in a way that instead a struct tpm_chip
instance is given and NULL means the default chip. In addition, this
commit refines the documentation to be up to date with the
implementation.

Suggested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> (@chip_num -> @chip part)
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgg@ziepe.ca>
Tested-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
2018-01-08 12:58:36 +02:00
Thiebaud Weksteen 58cc1e4faf tpm: parse TPM event logs based on EFI table
If we are not able to retrieve the TPM event logs from the ACPI table,
check the EFI configuration table (Linux-specific GUID).

The format version of the log is now returned by the provider function.

Signed-off-by: Thiebaud Weksteen <tweek@google.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Jarkko Sakkinen  <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen  <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen  <jarkko.sakkinen@linux.intel.com>
2018-01-08 12:58:35 +02:00
Thiebaud Weksteen 67cb8e113e tpm: rename event log provider files
Rename the current TPM Event Log provider files (ACPI and OF)
for clarity.

Signed-off-by: Thiebaud Weksteen <tweek@google.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Jarkko Sakkinen  <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen  <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen  <jarkko.sakkinen@linux.intel.com>
2018-01-08 12:58:34 +02:00
Thiebaud Weksteen fd3ec36637 tpm: move tpm_eventlog.h outside of drivers folder
The generic definitions of data structures in tpm_eventlog.h are
required by other part of the kernel (namely, the EFI stub).

Signed-off-by: Thiebaud Weksteen <tweek@google.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Jarkko Sakkinen  <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen  <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen  <jarkko.sakkinen@linux.intel.com>
2018-01-08 12:58:34 +02:00
Nayna Jain 5ef924d9e2 tpm: use tpm_msleep() value as max delay
Currently, tpm_msleep() uses delay_msec as the minimum value in
usleep_range. However, that is the maximum time we want to wait.
The function is modified to use the delay_msec as the maximum
value, not the minimum value.

After this change, performance on a TPM 1.2 with an 8 byte
burstcount for 1000 extends improved from ~9sec to ~8sec.

Fixes: 3b9af007869("tpm: replace msleep() with usleep_range() in TPM 1.2/
2.0 generic drivers")

Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Acked-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2018-01-08 12:58:33 +02:00
Nayna Jain cf151a9a44 tpm: reduce tpm polling delay in tpm_tis_core
The existing wait_for_tpm_stat() polls for the chip status after
5msec sleep. As per TCG ddwg input, it is expected that tpm might
return status in few usec. So, reducing the delay in polling to
1msec.
Similarly, get_burstcount() function sleeps for 5msec before
retrying for next query to burstcount in a loop. If it takes
lesser time for TPM to return, this 5msec delay is longer than
necessary.

After this change, performance on a TPM 1.2 with an 8 byte
burstcount for 1000 extends improved from ~14sec to ~9sec.

Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2018-01-08 12:58:33 +02:00
Nayna Jain 87cdfdd19a tpm: move wait_for_tpm_stat() to respective driver files
The function wait_for_tpm_stat() is currently defined in
tpm-interface file. It is a hardware specific function used
only by tpm_tis and xen-tpmfront, so it is removed from
tpm-interface.c and defined in respective driver files.

Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-12-16 20:27:32 +02:00
Al Viro afc9a42b74 the rest of drivers/*: annotate ->poll() instances
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2017-11-28 11:06:58 -05:00
Kees Cook e99e88a9d2 treewide: setup_timer() -> timer_setup()
This converts all remaining cases of the old setup_timer() API into using
timer_setup(), where the callback argument is the structure already
holding the struct timer_list. These should have no behavioral changes,
since they just change which pointer is passed into the callback with
the same available pointers after conversion. It handles the following
examples, in addition to some other variations.

Casting from unsigned long:

    void my_callback(unsigned long data)
    {
        struct something *ptr = (struct something *)data;
    ...
    }
    ...
    setup_timer(&ptr->my_timer, my_callback, ptr);

and forced object casts:

    void my_callback(struct something *ptr)
    {
    ...
    }
    ...
    setup_timer(&ptr->my_timer, my_callback, (unsigned long)ptr);

become:

    void my_callback(struct timer_list *t)
    {
        struct something *ptr = from_timer(ptr, t, my_timer);
    ...
    }
    ...
    timer_setup(&ptr->my_timer, my_callback, 0);

Direct function assignments:

    void my_callback(unsigned long data)
    {
        struct something *ptr = (struct something *)data;
    ...
    }
    ...
    ptr->my_timer.function = my_callback;

have a temporary cast added, along with converting the args:

    void my_callback(struct timer_list *t)
    {
        struct something *ptr = from_timer(ptr, t, my_timer);
    ...
    }
    ...
    ptr->my_timer.function = (TIMER_FUNC_TYPE)my_callback;

And finally, callbacks without a data assignment:

    void my_callback(unsigned long data)
    {
    ...
    }
    ...
    setup_timer(&ptr->my_timer, my_callback, 0);

have their argument renamed to verify they're unused during conversion:

    void my_callback(struct timer_list *unused)
    {
    ...
    }
    ...
    timer_setup(&ptr->my_timer, my_callback, 0);

The conversion is done with the following Coccinelle script:

spatch --very-quiet --all-includes --include-headers \
	-I ./arch/x86/include -I ./arch/x86/include/generated \
	-I ./include -I ./arch/x86/include/uapi \
	-I ./arch/x86/include/generated/uapi -I ./include/uapi \
	-I ./include/generated/uapi --include ./include/linux/kconfig.h \
	--dir . \
	--cocci-file ~/src/data/timer_setup.cocci

@fix_address_of@
expression e;
@@

 setup_timer(
-&(e)
+&e
 , ...)

// Update any raw setup_timer() usages that have a NULL callback, but
// would otherwise match change_timer_function_usage, since the latter
// will update all function assignments done in the face of a NULL
// function initialization in setup_timer().
@change_timer_function_usage_NULL@
expression _E;
identifier _timer;
type _cast_data;
@@

(
-setup_timer(&_E->_timer, NULL, _E);
+timer_setup(&_E->_timer, NULL, 0);
|
-setup_timer(&_E->_timer, NULL, (_cast_data)_E);
+timer_setup(&_E->_timer, NULL, 0);
|
-setup_timer(&_E._timer, NULL, &_E);
+timer_setup(&_E._timer, NULL, 0);
|
-setup_timer(&_E._timer, NULL, (_cast_data)&_E);
+timer_setup(&_E._timer, NULL, 0);
)

@change_timer_function_usage@
expression _E;
identifier _timer;
struct timer_list _stl;
identifier _callback;
type _cast_func, _cast_data;
@@

(
-setup_timer(&_E->_timer, _callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, &_callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, _callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, &_callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)_callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)&_callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)_callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)&_callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, &_callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, &_callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
 _E->_timer@_stl.function = _callback;
|
 _E->_timer@_stl.function = &_callback;
|
 _E->_timer@_stl.function = (_cast_func)_callback;
|
 _E->_timer@_stl.function = (_cast_func)&_callback;
|
 _E._timer@_stl.function = _callback;
|
 _E._timer@_stl.function = &_callback;
|
 _E._timer@_stl.function = (_cast_func)_callback;
|
 _E._timer@_stl.function = (_cast_func)&_callback;
)

// callback(unsigned long arg)
@change_callback_handle_cast
 depends on change_timer_function_usage@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _origtype;
identifier _origarg;
type _handletype;
identifier _handle;
@@

 void _callback(
-_origtype _origarg
+struct timer_list *t
 )
 {
(
	... when != _origarg
	_handletype *_handle =
-(_handletype *)_origarg;
+from_timer(_handle, t, _timer);
	... when != _origarg
|
	... when != _origarg
	_handletype *_handle =
-(void *)_origarg;
+from_timer(_handle, t, _timer);
	... when != _origarg
|
	... when != _origarg
	_handletype *_handle;
	... when != _handle
	_handle =
-(_handletype *)_origarg;
+from_timer(_handle, t, _timer);
	... when != _origarg
|
	... when != _origarg
	_handletype *_handle;
	... when != _handle
	_handle =
-(void *)_origarg;
+from_timer(_handle, t, _timer);
	... when != _origarg
)
 }

// callback(unsigned long arg) without existing variable
@change_callback_handle_cast_no_arg
 depends on change_timer_function_usage &&
                     !change_callback_handle_cast@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _origtype;
identifier _origarg;
type _handletype;
@@

 void _callback(
-_origtype _origarg
+struct timer_list *t
 )
 {
+	_handletype *_origarg = from_timer(_origarg, t, _timer);
+
	... when != _origarg
-	(_handletype *)_origarg
+	_origarg
	... when != _origarg
 }

// Avoid already converted callbacks.
@match_callback_converted
 depends on change_timer_function_usage &&
            !change_callback_handle_cast &&
	    !change_callback_handle_cast_no_arg@
identifier change_timer_function_usage._callback;
identifier t;
@@

 void _callback(struct timer_list *t)
 { ... }

// callback(struct something *handle)
@change_callback_handle_arg
 depends on change_timer_function_usage &&
	    !match_callback_converted &&
            !change_callback_handle_cast &&
            !change_callback_handle_cast_no_arg@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _handletype;
identifier _handle;
@@

 void _callback(
-_handletype *_handle
+struct timer_list *t
 )
 {
+	_handletype *_handle = from_timer(_handle, t, _timer);
	...
 }

// If change_callback_handle_arg ran on an empty function, remove
// the added handler.
@unchange_callback_handle_arg
 depends on change_timer_function_usage &&
	    change_callback_handle_arg@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _handletype;
identifier _handle;
identifier t;
@@

 void _callback(struct timer_list *t)
 {
-	_handletype *_handle = from_timer(_handle, t, _timer);
 }

// We only want to refactor the setup_timer() data argument if we've found
// the matching callback. This undoes changes in change_timer_function_usage.
@unchange_timer_function_usage
 depends on change_timer_function_usage &&
            !change_callback_handle_cast &&
            !change_callback_handle_cast_no_arg &&
	    !change_callback_handle_arg@
expression change_timer_function_usage._E;
identifier change_timer_function_usage._timer;
identifier change_timer_function_usage._callback;
type change_timer_function_usage._cast_data;
@@

(
-timer_setup(&_E->_timer, _callback, 0);
+setup_timer(&_E->_timer, _callback, (_cast_data)_E);
|
-timer_setup(&_E._timer, _callback, 0);
+setup_timer(&_E._timer, _callback, (_cast_data)&_E);
)

// If we fixed a callback from a .function assignment, fix the
// assignment cast now.
@change_timer_function_assignment
 depends on change_timer_function_usage &&
            (change_callback_handle_cast ||
             change_callback_handle_cast_no_arg ||
             change_callback_handle_arg)@
expression change_timer_function_usage._E;
identifier change_timer_function_usage._timer;
identifier change_timer_function_usage._callback;
type _cast_func;
typedef TIMER_FUNC_TYPE;
@@

(
 _E->_timer.function =
-_callback
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E->_timer.function =
-&_callback
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E->_timer.function =
-(_cast_func)_callback;
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E->_timer.function =
-(_cast_func)&_callback
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E._timer.function =
-_callback
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E._timer.function =
-&_callback;
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E._timer.function =
-(_cast_func)_callback
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E._timer.function =
-(_cast_func)&_callback
+(TIMER_FUNC_TYPE)_callback
 ;
)

// Sometimes timer functions are called directly. Replace matched args.
@change_timer_function_calls
 depends on change_timer_function_usage &&
            (change_callback_handle_cast ||
             change_callback_handle_cast_no_arg ||
             change_callback_handle_arg)@
expression _E;
identifier change_timer_function_usage._timer;
identifier change_timer_function_usage._callback;
type _cast_data;
@@

 _callback(
(
-(_cast_data)_E
+&_E->_timer
|
-(_cast_data)&_E
+&_E._timer
|
-_E
+&_E->_timer
)
 )

// If a timer has been configured without a data argument, it can be
// converted without regard to the callback argument, since it is unused.
@match_timer_function_unused_data@
expression _E;
identifier _timer;
identifier _callback;
@@

(
-setup_timer(&_E->_timer, _callback, 0);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, _callback, 0L);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, _callback, 0UL);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, 0);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, 0L);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, 0UL);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_timer, _callback, 0);
+timer_setup(&_timer, _callback, 0);
|
-setup_timer(&_timer, _callback, 0L);
+timer_setup(&_timer, _callback, 0);
|
-setup_timer(&_timer, _callback, 0UL);
+timer_setup(&_timer, _callback, 0);
|
-setup_timer(_timer, _callback, 0);
+timer_setup(_timer, _callback, 0);
|
-setup_timer(_timer, _callback, 0L);
+timer_setup(_timer, _callback, 0);
|
-setup_timer(_timer, _callback, 0UL);
+timer_setup(_timer, _callback, 0);
)

@change_callback_unused_data
 depends on match_timer_function_unused_data@
identifier match_timer_function_unused_data._callback;
type _origtype;
identifier _origarg;
@@

 void _callback(
-_origtype _origarg
+struct timer_list *unused
 )
 {
	... when != _origarg
 }

Signed-off-by: Kees Cook <keescook@chromium.org>
2017-11-21 15:57:07 -08:00
Linus Torvalds 55b3a0cb5a Merge branch 'next-general' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull general security subsystem updates from James Morris:
 "TPM (from Jarkko):
   - essential clean up for tpm_crb so that ARM64 and x86 versions do
     not distract each other as much as before

   - /dev/tpm0 rejects now too short writes (shorter buffer than
     specified in the command header

   - use DMA-safe buffer in tpm_tis_spi

   - otherwise mostly minor fixes.

  Smack:
   - base support for overlafs

  Capabilities:
   - BPRM_FCAPS fixes, from Richard Guy Briggs:

     The audit subsystem is adding a BPRM_FCAPS record when auditing
     setuid application execution (SYSCALL execve). This is not expected
     as it was supposed to be limited to when the file system actually
     had capabilities in an extended attribute. It lists all
     capabilities making the event really ugly to parse what is
     happening. The PATH record correctly records the setuid bit and
     owner. Suppress the BPRM_FCAPS record on set*id.

  TOMOYO:
   - Y2038 timestamping fixes"

* 'next-general' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (28 commits)
  MAINTAINERS: update the IMA, EVM, trusted-keys, encrypted-keys entries
  Smack: Base support for overlayfs
  MAINTAINERS: remove David Safford as maintainer for encrypted+trusted keys
  tomoyo: fix timestamping for y2038
  capabilities: audit log other surprising conditions
  capabilities: fix logic for effective root or real root
  capabilities: invert logic for clarity
  capabilities: remove a layer of conditional logic
  capabilities: move audit log decision to function
  capabilities: use intuitive names for id changes
  capabilities: use root_priveleged inline to clarify logic
  capabilities: rename has_cap to has_fcap
  capabilities: intuitive names for cap gain status
  capabilities: factor out cap_bprm_set_creds privileged root
  tpm, tpm_tis: use ARRAY_SIZE() to define TPM_HID_USR_IDX
  tpm: fix duplicate inline declaration specifier
  tpm: fix type of a local variables in tpm_tis_spi.c
  tpm: fix type of a local variable in tpm2_map_command()
  tpm: fix type of a local variable in tpm2_get_cc_attrs_tbl()
  tpm-dev-common: Reject too short writes
  ...
2017-11-13 10:30:44 -08:00
Greg Kroah-Hartman b24413180f License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02 11:10:55 +01:00
Jérémy Lefaure 33957a104c tpm, tpm_tis: use ARRAY_SIZE() to define TPM_HID_USR_IDX
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-10-18 18:28:49 +03:00
Ruben Roy 2d56c71835 tpm: fix duplicate inline declaration specifier
This commit fixes the duplicate inline declaration specifier in
tpm2_rc_value which caused a warning

Signed-off-by: Ruben Roy <rubenroy2005@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-10-18 18:28:49 +03:00
Jarkko Sakkinen 1a7a9b26c6 tpm: fix type of a local variables in tpm_tis_spi.c
Use __le32 type for data in that format.

Fixes: 0edbfea537 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
2017-10-18 18:28:48 +03:00
Jarkko Sakkinen 4557d4bedc tpm: fix type of a local variable in tpm2_map_command()
The local variable 'handle' should have the type __be32 instead of u32.

Fixes: 745b361e98 ("tpm: infrastructure for TPM spaces")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
2017-10-18 18:28:48 +03:00
Jarkko Sakkinen 171360d780 tpm: fix type of a local variable in tpm2_get_cc_attrs_tbl()
The local variable 'attrs' should have the type __be32 instead of u32.

Fixes: 58472f5cd4 ("tpm: validate TPM 2.0 commands")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
2017-10-18 18:28:48 +03:00
Alexander Steffen ee70bc1e7b tpm-dev-common: Reject too short writes
tpm_transmit() does not offer an explicit interface to indicate the number
of valid bytes in the communication buffer. Instead, it relies on the
commandSize field in the TPM header that is encoded within the buffer.
Therefore, ensure that a) enough data has been written to the buffer, so
that the commandSize field is present and b) the commandSize field does not
announce more data than has been written to the buffer.

This should have been fixed with CVE-2011-1161 long ago, but apparently
a correct version of that patch never made it into the kernel.

Cc: stable@vger.kernel.org
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-10-18 18:28:47 +03:00
Alexander Steffen 125a221054 tpm: React correctly to RC_TESTING from TPM 2.0 self tests
The TPM can choose one of two ways to react to the TPM2_SelfTest command.
It can either run all self tests synchronously and then return RC_SUCCESS
once all tests were successful. Or it can choose to run the tests
asynchronously and return RC_TESTING immediately while the self tests still
execute in the background.

The previous implementation apparently was not aware of those possibilities
and attributed RC_TESTING to some prototype chips instead. With this change
the return code of TPM2_SelfTest is interpreted correctly, i.e. the self
test result is polled if and only if RC_TESTING is received.

Unfortunately, the polling cannot be done in the most straightforward way.
If RC_TESTING is received, ideally the code should now poll the
selfTestDone bit in the STS register, as this avoids sending more commands,
that might interrupt self tests executing in the background and thus
prevent them from ever completing. But it cannot be guaranteed that this
bit is correctly implemented for all devices, so the next best thing would
be to use TPM2_GetTestResult to query the test result. But the response to
that command can be very long, and the code currently lacks the
capabilities for efficient unmarshalling, so it is difficult to execute
this command.

Therefore, we simply run the TPM2_SelfTest command in a loop, which should
complete eventually, since we only request the execution of self tests that
have not yet been done.

Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-10-18 18:28:47 +03:00
Alexander Steffen 87434f58be tpm: Use dynamic delay to wait for TPM 2.0 self test result
In order to avoid delaying the code longer than necessary while still
giving the TPM enough time to execute the self tests asynchronously, start
with a small delay between two polls and increase it each round.

Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-10-18 18:28:46 +03:00
Alexander Steffen 2482b1bba5 tpm: Trigger only missing TPM 2.0 self tests
tpm2_do_selftest is only used during initialization of the TPM to ensure
that the device functions correctly. Therefore, it is sufficient to request
only missing self tests (parameter full_test=0), not a reexecution of all
self tests, as was done before. This allows for a faster execution of this
command.

Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-10-18 18:28:46 +03:00
Alexander Steffen 6b3a13173f tpm_tis_spi: Use DMA-safe memory for SPI transfers
The buffers used as tx_buf/rx_buf in a SPI transfer need to be DMA-safe.
This cannot be guaranteed for the buffers passed to tpm_tis_spi_read_bytes
and tpm_tis_spi_write_bytes. Therefore, we need to use our own DMA-safe
buffer and copy the data to/from it.

The buffer needs to be allocated separately, to ensure that it is
cacheline-aligned and not shared with other data, so that DMA can work
correctly.

Fixes: 0edbfea537 ("tpm/tpm_tis_spi: Add support for spi phy")
Cc: stable@vger.kernel.org
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-10-18 18:28:46 +03:00
Jiandi An f5357413db tpm/tpm_crb: Use start method value from ACPI table directly
This patch gets rid of dealing with intermediate flag for start method
and use start method value from ACPI table directly.

For ARM64, the locality is handled by Trust Zone in FW.  The layout
does not have crb_regs_head.  It is hitting the following line.
dev_warn(dev, FW_BUG "Bad ACPI memory layout");

Current code excludes CRB_FL_ACPI_START for this check.  Now since
ARM64 support for TPM CRB is added, CRB_FL_CRB_SMC_START should also be
excluded from this check.

For goIdle and cmdReady where code was excluding CRB_FL_ACPI_START only
(do nothing for ACPI start method), CRB_FL_CRB_SMC_START was also
excluded as ARM64 SMC start method does not have TPM_CRB_CTRL_REQ.

However with special PPT workaround requiring CRB_FL_CRB_START to be
set in addition to CRB_FL_ACPI_START and the addition flag of SMC
start method CRB_FL_CRB_SMC_START, the code has become difficult to
maintain and undrestand.  It is better to make code deal with start
method value from ACPI table directly.

Signed-off-by: Jiandi An <anjiandi@codeaurora.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-10-18 18:28:45 +03:00
Arnd Bergmann c37fbc09bd tpm: constify transmit data pointers
Making cmd_getticks 'const' introduced a couple of harmless warnings:

drivers/char/tpm/tpm_tis_core.c: In function 'probe_itpm':
drivers/char/tpm/tpm_tis_core.c:469:31: error: passing argument 2 of 'tpm_tis_send_data' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
  rc = tpm_tis_send_data(chip, cmd_getticks, len);
drivers/char/tpm/tpm_tis_core.c:477:31: error: passing argument 2 of 'tpm_tis_send_data' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
  rc = tpm_tis_send_data(chip, cmd_getticks, len);
drivers/char/tpm/tpm_tis_core.c:255:12: note: expected 'u8 * {aka unsigned char *}' but argument is of type 'const u8 * {aka const unsigned char *}'
 static int tpm_tis_send_data(struct tpm_chip *chip, u8 *buf, size_t len)

This changes the related functions to all take 'const' pointers
so that gcc can see this as being correct. I had to slightly
modify the logic around tpm_tis_spi_transfer() for this to work
without introducing ugly casts.

Cc: stable@vger.kernel.org
Fixes: 5e35bd8e06b9 ("tpm_tis: make array cmd_getticks static const to shink object code size")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-10-18 18:28:45 +03:00
Colin Ian King 0bbc931a07 tpm_tis: make array cmd_getticks static const to shrink object code size
Don't populate array cmd_getticks on the stack, instead make it static
const.  Makes the object code smaller by over 160 bytes:

Before:
   text	   data	    bss	    dec	    hex	filename
  18813	   3152	    128	  22093	   564d	drivers/char/tpm/tpm_tis_core.o

After:
   text	   data	    bss	    dec	    hex	filename
  18554	   3248	    128	  21930	   55aa	drivers/char/tpm/tpm_tis_core.o

Cc: stable@vger.kernel.org
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-10-18 18:28:23 +03:00
Jarkko Sakkinen da379f3c1d tpm: migrate pubek_show to struct tpm_buf
Migrated pubek_show to struct tpm_buf and cleaned up its implementation.
Previously the output parameter structure was declared but left
completely unused. Now it is used to refer different fields of the
output. We can move it to tpm-sysfs.c as it does not have any use
outside of that file.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-10-12 14:28:59 +03:00
Linus Torvalds 1436ab068d Merge branch 'next-tpm' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull TPM updates from James Morris:
 "Here are the TPM updates from Jarkko for v4.14, which I've placed in
  their own branch (next-tpm). I ended up cherry-picking them as other
  changes had been made in Jarkko's branch after he sent me his original
  pull request.

  I plan on maintaining a separate branch for TPM (and other security
  subsystems) from now on.

  From Jarkko: 'Not much this time except a few fixes'"

* 'next-tpm' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  tpm: ibmvtpm: simplify crq initialization and document crq format
  tpm: replace msleep() with  usleep_range() in TPM 1.2/2.0 generic drivers
  Documentation: tpm: add powered-while-suspended binding documentation
  tpm: tpm_crb: constify acpi_device_id.
  tpm: vtpm: constify vio_device_id
2017-09-24 11:34:28 -07:00
Michal Suchanek fb154e0e0a tpm: ibmvtpm: simplify crq initialization and document crq format
The crq is passed in registers and is the same on BE and LE hosts.
However, current implementation allocates a structure on-stack to
represent the crq, initializes the members swapping them to BE, and
loads the structure swapping it from BE. This is pointless and causes
GCC warnings about ununitialized members. Get rid of the structure and
the warnings.

Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
2017-09-23 21:51:38 -07:00
Hamza Attak 9f3fc7bcdd tpm: replace msleep() with usleep_range() in TPM 1.2/2.0 generic drivers
The patch simply replaces all msleep function calls with usleep_range calls
in the generic drivers.

Tested with an Infineon TPM 1.2, using the generic tpm-tis module, for a
thousand PCR extends, we see results going from 1m57s unpatched to 40s
with the new patch. We obtain similar results when using the original and
patched tpm_infineon driver, which is also part of the patch.
Similarly with a STM TPM 2.0, using the CRB driver, it takes about 20ms per
extend unpatched and around 7ms with the new patch.

Note that the PCR consistency is untouched with this patch, each TPM has
been tested with 10 million extends and the aggregated PCR value is
continuously verified to be correct.

As an extension of this work, this could potentially and easily be applied
to other vendor's drivers. Still, these changes are not included in the
proposed patch as they are untested.

Signed-off-by: Hamza Attak <hamza@hpe.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
2017-09-23 21:51:00 -07:00
Arvind Yadav e1ec650f9a tpm: tpm_crb: constify acpi_device_id.
acpi_device_id are not supposed to change at runtime. All functions
working with acpi_device_id provided by <acpi/acpi_bus.h> work with
const acpi_device_id. So mark the non-const structs as const.

File size before:
   text	   data	    bss	    dec	    hex	filename
   4198	    608	      0	   4806	   12c6	drivers/char/tpm/tpm_crb.o

File size After adding 'const':
   text	   data	    bss	    dec	    hex	filename
   4262	    520	      0	   4782	   12ae	drivers/char/tpm/tpm_crb.o

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
2017-09-23 21:49:52 -07:00
Arvind Yadav c2a9c4bf03 tpm: vtpm: constify vio_device_id
vio_device_id are not supposed to change at runtime. All functions
working with vio_device_id provided by <asm/vio.h> work with
const vio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
2017-09-23 21:48:56 -07:00
Michal Suchanek 7521621e60 Do not disable driver and bus shutdown hook when class shutdown hook is set.
As seen from the implementation of the single class shutdown hook this
is not very sound design.

Rename the class shutdown hook to shutdown_pre to make it clear it runs
before the driver shutdown hook.

Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-28 18:02:46 +02:00
Enric Balletbo i Serra b5d0ebc99b tpm: do not suspend/resume if power stays on
The suspend/resume behavior of the TPM can be controlled by setting
"powered-while-suspended" in the DTS. This is useful for the cases
when hardware does not power-off the TPM.

Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
2017-07-07 09:49:26 +10:00
Roberto Sassu 28707bf221 tpm: use tpm2_pcr_read() in tpm2_do_selftest()
tpm2_do_selftest() performs a PCR read during the TPM initialization phase.
This patch replaces the PCR read code with a call to tpm2_pcr_read().

Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
2017-07-07 09:49:26 +10:00
Roberto Sassu 91f7f3d773 tpm: use tpm_buf functions in tpm2_pcr_read()
tpm2_pcr_read() now builds the PCR read command buffer with tpm_buf
functions. This solution is preferred to using a tpm2_cmd structure,
as tpm_buf functions provide protection against buffer overflow.

Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
2017-07-07 09:49:25 +10:00
Colin Ian King bc397085ca tpm_tis: make ilb_base_addr static
The pointer ilb_base_addr does not need to be in global scope, so make
it static.

Cleans up sparse warning:
"symbol 'ilb_base_addr' was not declared. Should it be static?"

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
2017-07-07 09:49:25 +10:00
Jarkko Sakkinen 19cbe4f680 tpm: consolidate the TPM startup code
Consolidated all the "manual" TPM startup code to a single function
in order to make code flows a bit cleaner and migrate to tpm_buf.

Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
2017-07-07 09:49:25 +10:00
Azhar Shaikh 5e572cab92 tpm: Enable CLKRUN protocol for Braswell systems
To overcome a hardware limitation on Intel Braswell systems,
disable CLKRUN protocol during TPM transactions and re-enable
once the transaction is completed.

Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
2017-07-07 09:49:25 +10:00
Manuel Lauss f128480f39 tpm/tpm_crb: fix priv->cmd_size initialisation
priv->cmd_size is never initialised if the cmd and rsp buffers reside
at different addresses.  Initialise it in the exit path of the function
when rsp buffer has also been successfully allocated.

Fixes: aa77ea0e43 ("tpm/tpm_crb: cache cmd_size register value.").
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
2017-07-07 09:49:25 +10:00
Jarkko Sakkinen 13b47cfcfc tpm: fix a kernel memory leak in tpm-sysfs.c
While cleaning up sysfs callback that prints EK we discovered a kernel
memory leak. This commit fixes the issue by zeroing the buffer used for
TPM command/response.

The leak happen when we use either tpm_vtpm_proxy, tpm_ibmvtpm or
xen-tpmfront.

Cc: stable@vger.kernel.org
Fixes: 0883743825 ("TPM: sysfs functions consolidation")
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
2017-07-07 09:49:24 +10:00
Josh Zimmerman d1bd4a792d tpm: Issue a TPM2_Shutdown for TPM2 devices.
If a TPM2 loses power without a TPM2_Shutdown command being issued (a
"disorderly reboot"), it may lose some state that has yet to be
persisted to NVRam, and will increment the DA counter. After the DA
counter gets sufficiently large, the TPM will lock the user out.

NOTE: This only changes behavior on TPM2 devices. Since TPM1 uses sysfs,
and sysfs relies on implicit locking on chip->ops, it is not safe to
allow this code to run in TPM1, or to add sysfs support to TPM2, until
that locking is made explicit.

Signed-off-by: Josh Zimmerman <joshz@google.com>
Cc: stable@vger.kernel.org
Fixes: 74d6b3ceaa ("tpm: fix suspend/resume paths for TPM 2.0")
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
2017-07-07 09:49:24 +10:00
Linus Torvalds e24dd9ee53 Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull security layer updates from James Morris:

 - a major update for AppArmor. From JJ:

     * several bug fixes and cleanups

     * the patch to add symlink support to securityfs that was floated
       on the list earlier and the apparmorfs changes that make use of
       securityfs symlinks

     * it introduces the domain labeling base code that Ubuntu has been
       carrying for several years, with several cleanups applied. And it
       converts the current mediation over to using the domain labeling
       base, which brings domain stacking support with it. This finally
       will bring the base upstream code in line with Ubuntu and provide
       a base to upstream the new feature work that Ubuntu carries.

     * This does _not_ contain any of the newer apparmor mediation
       features/controls (mount, signals, network, keys, ...) that
       Ubuntu is currently carrying, all of which will be RFC'd on top
       of this.

 - Notable also is the Infiniband work in SELinux, and the new file:map
   permission. From Paul:

      "While we're down to 21 patches for v4.13 (it was 31 for v4.12),
       the diffstat jumps up tremendously with over 2k of line changes.

       Almost all of these changes are the SELinux/IB work done by
       Daniel Jurgens; some other noteworthy changes include a NFS v4.2
       labeling fix, a new file:map permission, and reporting of policy
       capabilities on policy load"

   There's also now genfscon labeling support for tracefs, which was
   lost in v4.1 with the separation from debugfs.

 - Smack incorporates a safer socket check in file_receive, and adds a
   cap_capable call in privilege check.

 - TPM as usual has a bunch of fixes and enhancements.

 - Multiple calls to security_add_hooks() can now be made for the same
   LSM, to allow LSMs to have hook declarations across multiple files.

 - IMA now supports different "ima_appraise=" modes (eg. log, fix) from
   the boot command line.

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (126 commits)
  apparmor: put back designators in struct initialisers
  seccomp: Switch from atomic_t to recount_t
  seccomp: Adjust selftests to avoid double-join
  seccomp: Clean up core dump logic
  IMA: update IMA policy documentation to include pcr= option
  ima: Log the same audit cause whenever a file has no signature
  ima: Simplify policy_func_show.
  integrity: Small code improvements
  ima: fix get_binary_runtime_size()
  ima: use ima_parse_buf() to parse template data
  ima: use ima_parse_buf() to parse measurements headers
  ima: introduce ima_parse_buf()
  ima: Add cgroups2 to the defaults list
  ima: use memdup_user_nul
  ima: fix up #endif comments
  IMA: Correct Kconfig dependencies for hash selection
  ima: define is_ima_appraise_enabled()
  ima: define Kconfig IMA_APPRAISE_BOOTPARAM option
  ima: define a set of appraisal rules requiring file signatures
  ima: extend the "ima_policy" boot command line to support multiple policies
  ...
2017-07-05 11:26:35 -07:00
Linus Torvalds eceeae414e ACPI updates for v4.13-rc1
- Update the ACPICA code in the kernel to upstream revision
    revision 20170531 (which covers all of the new material from
    ACPI 6.2) including:
    * Support for the PinFunction(), PinConfig(), PinGroup(),
      PinGroupFunction(), and PinGroupConfig() resource descriptors
      (Mika Westerberg).
    * Support for new subtables in HEST and SRAT, new notify value
      for HEST, header support for TPM2 table changes, and BGRT
      Status field update (Bob Moore).
    * Support for new PCCT subtables (David Box).
    * Support for _LSI, _LSR, _LSW, and _HMA as predefined methods
      (Erik Schmauss).
    * Support for the new WSMT, HMAT, and PPTT tables (Lv Zheng).
    * New UUID values for Processor Properties (Bob Moore).
    * New notify values for memory attributes and graceful shutdown
      (Bob Moore).
    * Fix related to the PCAT_COMPAT MADT flag (Janosch Hildebrand).
    * Resource to AML conversion fix for resources containing GPIOs
      (Mika Westerberg).
    * Disassembler-related updates (Bob Moore, David Box, Erik
      Schmauss).
    * Assorted fixes and cleanups (Bob Moore, Erik Schmauss, Lv Zheng,
      Cao Jin).
 
  - Modify ACPICA to always use designated initializers for function
    pointer structures to make the structure layout randomization GCC
    plugin work with it (Kees Cook).
 
  - Update the tables configfs interface to unload SSDTs on configfs
    entry removal (Jan Kiszka).
 
  - Add support for the GPI1 regulator to the xpower PMIC Operation
    Region handler (Hans de Goede).
 
  - Fix ACPI EC issues related to conflicting EC definitions in the
    ECDT and in the ACPI namespace (Lv Zheng, Carlo Caione, Chris
    Chiu).
 
  - Fix an interrupt storm issue in the EC driver and make its debug
    output work with dynamic debug as expected (Lv Zheng).
 
  - Add ACPI backlight quirk for Dell Precision 7510 (Shih-Yuan Lee).
 
  - Fix whitespace in pr_fmt() to align log entries properly in some
    places in the ACPI subsystem (Vincent Legoll).
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJZWrJyAAoJEILEb/54YlRxY2cP/1h2un46sEnP7uLVLK4lpEih
 NQ79+fA7NTidA9J6gin2Kjgl8BFgswAhQBJZG3cJxUrhIIRWItSeLGvHb0CXX+iY
 m7CpL0ralIKV9XCju8B5b2V+0qn2tPzHS5a8PSX9Gvs0N6G8Qnlq4jspIjXMa3zH
 3D/fmYbQZeuHjypiBqRlB5IE49O2FQL2+d4Vn1rryuAFFya610ulASOZxsQ015d4
 Xt2pSTqUbqeD8rG8+j4VKFy8x0Lj0eEU3FUgYNJHlO+pOG+wTTs3KPyNOa33h0OC
 US0Wc0XOUyz78P5YkEgA7Ve/j1E6bqQ9bVF6mIcqjvAOReqSe84RCJ86Ckjlewxf
 VMNjCT/qDDkB8d+IAX6e7uYwxuP8bTSfUGBHjoI16qaJ13zd1/jOVY8QH5zPg5Ml
 r06HO5iOrQS3yhumYRk3gIdV+cgdHt3SEQlfi30nFH5Yzp8epk85UPyjYUYPDwqy
 QP5QbYvmHyuIUSXW2HQxZYADSaqnKIglRizCIKcFHT5+J554DjM5T51A5UpyQkY3
 cjtgrpg4KA5qCrpUAqPPxA2mtUVsZk1h4HwhrkTVt4xaR9GP9gvvzonP552fmHrM
 nIX9tM2JEf+LC7eCV+yrk8dtGNTRYpmEBQw7go4R82pTE5YTOWDf1bNM59gTFoWP
 LXi28C9lb2aibWlX/0bw
 =ImFw
 -----END PGP SIGNATURE-----

Merge tag 'acpi-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull ACPI updates from Rafael Wysocki:
 "These mostly update the ACPICA code in the kernel to upstream revision
  20170531 which covers all of the new material from ACPI 6.2, including
  new tables (WSMT, HMAT, PPTT), new subtables and definition changes
  for some existing tables (BGRT, HEST, SRAT, TPM2, PCCT), new resource
  descriptor macros for pin control, support for new predefined methods
  (_LSI, _LSR, _LSW, _HMA), fixes and cleanups.

  On top of that, an additional ACPICA change from Kees (which also is
  upstream already) switches all of the definitions of function pointer
  structures in ACPICA to use designated initializers so as to make the
  structure layout randomization GCC plugin work with it.

  The rest is a few fixes and cleanups in the EC driver, an xpower PMIC
  driver update, a new backlight blacklist entry, and update of the
  tables configfs interface and a messages formatting cleanup.

  Specifics:

   - Update the ACPICA code in the kernel to upstream revision revision
     20170531 (which covers all of the new material from ACPI 6.2)
     including:
      * Support for the PinFunction(), PinConfig(), PinGroup(),
        PinGroupFunction(), and PinGroupConfig() resource descriptors
        (Mika Westerberg).
      * Support for new subtables in HEST and SRAT, new notify value for
        HEST, header support for TPM2 table changes, and BGRT Status
        field update (Bob Moore).
      * Support for new PCCT subtables (David Box).
      * Support for _LSI, _LSR, _LSW, and _HMA as predefined methods
        (Erik Schmauss).
      * Support for the new WSMT, HMAT, and PPTT tables (Lv Zheng).
      * New UUID values for Processor Properties (Bob Moore).
      * New notify values for memory attributes and graceful shutdown
        (Bob Moore).
      * Fix related to the PCAT_COMPAT MADT flag (Janosch Hildebrand).
      * Resource to AML conversion fix for resources containing GPIOs
        (Mika Westerberg).
      * Disassembler-related updates (Bob Moore, David Box, Erik
        Schmauss).
      * Assorted fixes and cleanups (Bob Moore, Erik Schmauss, Lv Zheng,
        Cao Jin).

   - Modify ACPICA to always use designated initializers for function
     pointer structures to make the structure layout randomization GCC
     plugin work with it (Kees Cook).

   - Update the tables configfs interface to unload SSDTs on configfs
     entry removal (Jan Kiszka).

   - Add support for the GPI1 regulator to the xpower PMIC Operation
     Region handler (Hans de Goede).

   - Fix ACPI EC issues related to conflicting EC definitions in the
     ECDT and in the ACPI namespace (Lv Zheng, Carlo Caione, Chris
     Chiu).

   - Fix an interrupt storm issue in the EC driver and make its debug
     output work with dynamic debug as expected (Lv Zheng).

   - Add ACPI backlight quirk for Dell Precision 7510 (Shih-Yuan Lee).

   - Fix whitespace in pr_fmt() to align log entries properly in some
     places in the ACPI subsystem (Vincent Legoll)"

* tag 'acpi-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (63 commits)
  ACPI / EC: Add quirk for GL720VMK
  ACPI / EC: Fix media keys not working problem on some Asus laptops
  ACPI / EC: Add support to skip boot stage DSDT probe
  ACPI / EC: Enhance boot EC sanity check
  ACPI / video: Add quirks for the Dell Precision 7510
  ACPI: EC: Fix EC command visibility for dynamic debug
  ACPI: EC: Fix an EC event IRQ storming issue
  ACPICA: Use designated initializers
  ACPICA: Update version to 20170531
  ACPICA: Update a couple of debug output messages
  ACPICA: acpiexec: enhance local signal handler
  ACPICA: Simplify output for the ACPI Debug Object
  ACPICA: Unix application OSL: Correctly handle control-c (EINTR)
  ACPICA: Improvements for debug output only
  ACPICA: Disassembler: allow conflicting external declarations to be emitted.
  ACPICA: Disassembler: add external op to namespace on first pass
  ACPICA: Disassembler: prevent external op's from opening a new scope
  ACPICA: Changed Gbl_disasm_flag to acpi_gbl_disasm_flag
  ACPICA: Changing External to a named object
  ACPICA: Update two error messages to emit control method name
  ...
2017-07-04 14:16:49 -07:00
Gustavo A. R. Silva e4b0852798 tpm/tpm_atmel: remove unnecessary NULL check
Remove unnecessary NULL check.
Pointer _chip_ cannot be NULL in this instance.

Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com> (compilation)
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-06-19 02:36:04 +02:00
Andy Shevchenko 23c3beae58 tpm/st33zp24: Switch to devm_acpi_dev_add_driver_gpios()
Switch to use managed variant of acpi_dev_add_driver_gpios() to simplify
error path and fix potentially wrong assignment if ->probe() fails.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com> (compilation)
Signed-off-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
2017-06-19 02:33:22 +02:00
Stefan Berger d8b5d94538 tpm: vtpm_proxy: Prevent userspace from sending driver command
To prevent userspace from sending the TPM driver command to set
the locality, we need to check every command that is sent from
user space. To distinguish user space commands from internally
sent commands we introduce an additional state flag
STATE_DRIVER_COMMAND that is set while the driver sends this
command. Similar to the TPM 2 space commands we return an error
code when this command is detected.

Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-06-13 22:02:09 +03:00
Stefan Berger be4c9acfe2 tpm: vtpm_proxy: Implement request_locality function.
Implement the request_locality function. To set the locality on the
backend we define vendor-specific TPM 1.2 and TPM 2 ordinals and send
a command to the backend to set the locality for the next commands.

To avoid recursing into requesting the locality, we set the
TPM_TRANSMIT_RAW flag when calling tpm_transmit_cmd. To avoid recursing
into TPM 2 space related commands, we set the space parameter to NULL.

Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-06-13 22:02:09 +03:00
Stefan Berger 85ab3bf305 tpm: Introduce flag TPM_TRANSMIT_RAW
Introduce the flag TPM_TRANSMIT_RAW that allows us to transmit
a command without recursing into the requesting of locality.

Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-06-13 22:02:09 +03:00
Stefan Berger 402149c647 tpm: vtpm_proxy: Suppress error logging when in closed state
Suppress the error logging when the core TPM driver sends commands
to the VTPM proxy driver and -EPIPE is returned in case the VTPM
proxy driver is 'closed' (closed anonymous file descriptor).  This
error code is only returned by the send function and by tpm_transmit
when the VTPM proxy driver is being used.

Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-06-13 22:02:09 +03:00
Peter Huewe 5e9fefd26b tpm, tpmrm: Mark tpmrm_write as static
sparse complains that tpmrm_write can be made static, and since it is
right we make it static.

Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-06-13 22:02:08 +03:00
Jarkko Sakkinen 8816188f06 tpm: remove struct tpm_pcrextend_in
Removed struct tpm_pcrextend_in as it is not used for anything anymore.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
2017-06-13 22:02:08 +03:00
Jarkko Sakkinen 30bbafe3e0 tpm, tpm_infineon: remove useless snprintf() calls
The memory copy from rodata to stack is useless.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
2017-06-13 22:02:08 +03:00
Jarkko Sakkinen 124bdcf4a6 tpm: fix byte order related arithmetic inconsistency in tpm_getcap()
You should not do arithmetic with __be32 or __le32 types because
sometimes it results incorrect results. Calculations must be done only
with integers that are in in the CPU byte order. This commit migrates
tpm_getcap() to struct tpm_buf in order to sort out these issues.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
2017-06-13 22:02:08 +03:00
Bryan Freed d8c3eab5cb tpm: Apply a sane minimum adapterlimit value for retransmission.
When the I2C Infineon part is attached to an I2C adapter that imposes
a size limitation, large requests will fail with -EOPNOTSUPP. Retry
them with a sane minimum size without re-issuing the 0x05 command
as this appears to occasionally put the TPM in a bad state.

Signed-off-by: Bryan Freed <bfreed@chromium.org>
[rework the patch to adapt to the feedback received]
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-06-13 22:02:08 +03:00
Jason Gunthorpe 4cb586a188 tpm_tis: Consolidate the platform and acpi probe flow
Now that the platform device was merged for OF support we can use the
platform device to match ACPI devices as well and run everything
through tpm_tis_init.

pnp_acpi_device is replaced with ACPI_COMPANION, and ACPI_HANDLE is
pushed further down.

platform_get_resource is used instead of acpi_dev_get_resources.

The itpm global module parameter is no longer changed during itpm
detection, instead the phy specific bit is set directly.

Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jerry Snitselaar <jsnitsel@redhat.com> (with TPM 2.0)
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> (with TPM 1.2)
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-06-13 22:02:08 +03:00
Jason Gunthorpe fc0e132229 tpm_tis: Use platform_get_irq
Replace the open coded IORESOURCE_IRQ with platform_get_irq, which
supports more cases.

Fixes: 00194826e6 ("tpm_tis: Clean up the force=1 module parameter")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jerry Snitselaar <jsnitsel@redhat.com> (with TPM 2.0)
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> (with TPM 1.2)
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-06-13 22:02:08 +03:00
Jason Gunthorpe d27f81f061 tpm_tis: Fix IRQ autoprobing when using platform_device
The test was backwards, triggering IRQ autoprobing if the firmware
did not specify an IRQ, instead of triggering it only when the
module force parameter was specified.

Since autoprobing is not enabled on !x86 and the platform device is
currently only used on !x86, or with force, this has gone unnoticed.

Fixes: 00194826e6 ("tpm_tis: Clean up the force=1 module parameter")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jerry Snitselaar <jsnitsel@redhat.com> (with TPM 2.0)
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> (with TPM 1.2)
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-06-13 22:02:08 +03:00
Roberto Sassu 175d5b2a57 tpm: move TPM 1.2 code of tpm_pcr_extend() to tpm1_pcr_extend()
In preparation of the modifications to tpm_pcr_extend(), which will
allow callers to supply a digest for each PCR bank of a TPM 2.0,
the TPM 1.2 specific code has been moved to tpm1_pcr_extend().

tpm1_pcr_extend() uses tpm_buf_init() to prepare the command buffer,
which offers protection against buffer overflow. It is called by
tpm_pcr_extend() and tpm_pm_suspend().

Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-06-13 22:02:08 +03:00
Roberto Sassu a69faebf4d tpm: move endianness conversion of ordinals to tpm_input_header
Move CPU native value to big-endian conversion of ordinals to the
tpm_input_header declarations.

With the previous and this patch it will now be possible to modify TPM 1.2
functions to use tpm_buf_init(), which expects CPU native value for the
tag and ordinal arguments.

Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-06-13 22:02:08 +03:00
Roberto Sassu 06e93279ca tpm: move endianness conversion of TPM_TAG_RQU_COMMAND to tpm_input_header
In the long term, TPM 1.2 functions in the driver interface will be
modified to use tpm_buf_init().

However, tag and ordinals cannot be passed directly to tpm_buf_init(),
because this function performs CPU native to big-endian conversion of these
arguments. Since TPM_TAG_RQU_COMMAND and TPM_ORD_ are already converted,
passing them to the function will undo the previous conversion.

This patch moves the conversion of TPM_TAG_RQU_COMMAND from the tpm.h
header file in the driver directory to the tpm_input_header declarations
in the driver interface and tpm-sysfs.c.

Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-06-13 22:02:08 +03:00
Bob Moore bff7f90bbe ACPICA: Add header support for TPM2 table changes
ACPICA commit b922ecaf9053dae3b8933664e951ed1ee8f86f07

Update to new version of the TCG/ACPI spec.
Does not include table compiler or disassembler support.

Link: https://github.com/acpica/acpica/commit/b922ecaf
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-06-12 14:58:38 +02:00
Andy Shevchenko 94116f8126 ACPI: Switch to use generic guid_t in acpi_evaluate_dsm()
acpi_evaluate_dsm() and friends take a pointer to a raw buffer of 16
bytes. Instead we convert them to use guid_t type. At the same time we
convert current users.

acpi_str_to_uuid() becomes useless after the conversion and it's safe to
get rid of it.

Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
2017-06-07 12:20:49 +02:00
Linus Torvalds af82455f7d char/misc patches for 4.12-rc1
Here is the big set of new char/misc driver drivers and features for
 4.12-rc1.
 
 There's lots of new drivers added this time around, new firmware drivers
 from Google, more auxdisplay drivers, extcon drivers, fpga drivers, and
 a bunch of other driver updates.  Nothing major, except if you happen to
 have the hardware for these drivers, and then you will be happy :)
 
 All of these have been in linux-next for a while with no reported
 issues.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWQvAgg8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+yknsACgzkAeyz16Z97J3UTaeejbR7nKUCAAoKY4WEHY
 8O9f9pr9gj8GMBwxeZQa
 =OIfB
 -----END PGP SIGNATURE-----

Merge tag 'char-misc-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc

Pull char/misc driver updates from Greg KH:
 "Here is the big set of new char/misc driver drivers and features for
  4.12-rc1.

  There's lots of new drivers added this time around, new firmware
  drivers from Google, more auxdisplay drivers, extcon drivers, fpga
  drivers, and a bunch of other driver updates. Nothing major, except if
  you happen to have the hardware for these drivers, and then you will
  be happy :)

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'char-misc-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (136 commits)
  firmware: google memconsole: Fix return value check in platform_memconsole_init()
  firmware: Google VPD: Fix return value check in vpd_platform_init()
  goldfish_pipe: fix build warning about using too much stack.
  goldfish_pipe: An implementation of more parallel pipe
  fpga fr br: update supported version numbers
  fpga: region: release FPGA region reference in error path
  fpga altera-hps2fpga: disable/unprepare clock on error in alt_fpga_bridge_probe()
  mei: drop the TODO from samples
  firmware: Google VPD sysfs driver
  firmware: Google VPD: import lib_vpd source files
  misc: lkdtm: Add volatile to intentional NULL pointer reference
  eeprom: idt_89hpesx: Add OF device ID table
  misc: ds1682: Add OF device ID table
  misc: tsl2550: Add OF device ID table
  w1: Remove unneeded use of assert() and remove w1_log.h
  w1: Use kernel common min() implementation
  uio_mf624: Align memory regions to page size and set correct offsets
  uio_mf624: Refactor memory info initialization
  uio: Allow handling of non page-aligned memory regions
  hangcheck-timer: Fix typo in comment
  ...
2017-05-04 19:15:35 -07:00
Stefan Berger 8979b02aaf tpm: Fix reference count to main device
The main device is currently not properly released due to one additional
reference to the 'devs' device which is only released in case of a TPM 2.
So, also get the additional reference only in case of a TPM2.

Fixes: fdc915f7f7 ("tpm: expose spaces via a device link /dev/tpmrm<n>")
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-04-25 00:27:18 +03:00
Jerry Snitselaar e6aef069b6 tpm_tis: convert to using locality callbacks
This patch converts tpm_tis to use of the new tpm class ops
request_locality, and relinquish_locality.

With the move to using the callbacks, release_locality is changed so
that we now release the locality even if there is no request pending.

This required some changes to the tpm_tis_core_init code path to
make sure locality is requested when needed:

  - tpm2_probe code path will end up calling request/release through
    callbacks, so request_locality prior to tpm2_probe not needed.

  - probe_itpm makes calls to tpm_tis_send_data which no longer calls
    request_locality, so add request_locality prior to tpm_tis_send_data
    calls. Also drop release_locality call in middleof probe_itpm, and
    keep locality until release_locality called at end of probe_itpm.

Cc: Peter Huewe <peterhuewe@gmx.de>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Marcel Selhorst <tpmdd@selhorst.net>
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-04-25 00:27:18 +03:00
Petr Vandrovec fd5c78694f tpm: fix handling of the TPM 2.0 event logs
When TPM2 log has entries with more than 3 digests, or with digests
not listed in the log header, log gets misparsed, eventually
leading to kernel complaint that code tried to vmalloc 512MB of
memory (I have no idea what would happen on bigger system).

So code should not parse only first 3 digests: both event header
and event itself are already in memory, so we can parse any number
of digests, as long as we do not try to parse whole memory when
given count of 0xFFFFFFFF.

So this change:

* Rejects event entry with more digests than log header describes.
  Digest types should be unique, and all should be described in
  log header, so there cannot be more digests in the event than in
  the header.

* Reject event entry with digest that is not described in the
  log header.  In theory code could hardcode information about
  digest IDs already assigned by TCG, but if firmware authors
  cannot get event log format right, why should anyone believe
  that they got event log content right.

Cc: stable@vger.kernel.org
Fixes: 4d23cc323c ("tpm: add securityfs support for TPM 2.0 firmware event log")
Signed-off-by: Petr Vandrovec <petr@vmware.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-04-25 00:27:18 +03:00
Jarkko Sakkinen 3b395d67d9 tpm_crb: remove a cruft constant
Remove a useless constant that slipped through me when I did the code
review. This commit fixes the issue.

Cc: Jiandi An <anjiandi@codeaurora.org>
Fixes: 69c558de63c7 ("tpm/tpm_crb: Enable TPM CRB interface for ARM64")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-04-25 00:27:18 +03:00
Jiandi An 08eff49d63 tpm/tpm_crb: Enable TPM CRB interface for ARM64
This enables TPM Command Response Buffer interface driver for
ARM64 and implements an ARM specific TPM CRB start method that
invokes a Secure Monitor Call (SMC) to request the TrustZone
Firmware to execute or cancel a TPM 2.0 command.

In ARM, TrustZone security extensions enable a secure software
environment with Secure Monitor mode.  A Secure Monitor Call
(SMC) is used to enter the Secure Monitor mode and perform a
Secure Monitor service to communicate with TrustZone firmware
which has control over the TPM hardware.

Signed-off-by: Jiandi An <anjiandi@codeaurora.org>
Tested-by: Shanker Donthineni <shankerd@codeaurora.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> (on x86/PTT)
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-04-03 22:46:03 +03:00
Jarkko Sakkinen 877c57d0d0 tpm_crb: request and relinquish locality 0
This commit adds support for requesting and relinquishing locality 0 in
tpm_crb for the course of command transmission.

In order to achieve this, two new callbacks are added to struct
tpm_class_ops:

- request_locality
- relinquish_locality

With CRB interface you first set either requestAccess or relinquish bit
from TPM_LOC_CTRL_x register and then wait for locAssigned and
tpmRegValidSts bits to be set in the TPM_LOC_STATE_x register.

The reason why were are doing this is to make sure that the driver
will work properly with Intel TXT that uses locality 2. There's no
explicit guarantee that it would relinquish this locality. In more
general sense this commit enables tpm_crb to be a well behaving
citizen in a multi locality environment.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Jerry Snitselaar <jsnitsel@redhat.com>
2017-04-03 22:46:02 +03:00
Jerry Snitselaar 84d2594067 tpm: make check_locality return bool
Since check_locality is checking to see if a certain
locality is active, return true if active otherwise
return false.

Cc: Christophe Ricard <christophe.ricard@gmail.com>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Marcel Selhorst <tpmdd@selhorst.net>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-04-03 22:46:02 +03:00
Jérémy Lefaure 67c2f3d388 tpm/tpm_crb: fix unused warnings on suspend/resume functions
When PM_SLEEP is disabled crb_pm_suspend and crb_pm_resume are not used by
SET_SYSTEM_SLEEP_PM_OPS even if PM is enabled:

drvers/char/tpm/tpm_crb.c:540:12: warning: ‘crb_pm_suspend’ defined but not
used [-Wunused-function]
 static int crb_pm_suspend(struct device *dev)
            ^
drivers/char/tpm/tpm_crb.c:551:12: warning: ‘crb_pm_resume’ defined but not
used [-Wunused-function]
 static int crb_pm_resume(struct device *dev)
            ^

The preprocessor condition should be on CONFIG_PM_SLEEP, not on CONFIG_PM.
However, this patch fixes this warning by using __maybe_unused on function
that are in the preprocessor condition.

Fixes: 848efcfb560c ("tpm/tpm_crb: enter the low power state upon device suspend")
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-04-03 22:46:02 +03:00
Nayna Jain 0afb7118ae tpm: add sleep only for retry in i2c_nuvoton_write_status()
Currently, there is an unnecessary 1 msec delay added in
i2c_nuvoton_write_status() for the successful case. This
function is called multiple times during send() and recv(),
which implies adding multiple extra delays for every TPM
operation.

This patch calls usleep_range() only if retry is to be done.

Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org (linux-4.8)
Reviewed-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-04-03 22:46:02 +03:00
Andy Shevchenko 2d2e376f05 tpm/st33zp24: Add GPIO ACPI mapping table
In order to make GPIO ACPI library stricter prepare users of
gpiod_get_index() to correctly behave when there no mapping is
provided by firmware.

Here we add explicit mapping between _CRS GpioIo() resources and
their names used in the driver.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-04-03 22:46:02 +03:00
Hon Ching \(Vicky\) Lo 31574d321c vTPM: Fix missing NULL check
The current code passes the address of tpm_chip as the argument to
dev_get_drvdata() without prior NULL check in
tpm_ibmvtpm_get_desired_dma.  This resulted an oops during kernel
boot when vTPM is enabled in Power partition configured in active
memory sharing mode.

The vio_driver's get_desired_dma() is called before the probe(), which
for vtpm is tpm_ibmvtpm_probe, and it's this latter function that
initializes the driver and set data.  Attempting to get data before
the probe() caused the problem.

This patch adds a NULL check to the tpm_ibmvtpm_get_desired_dma.

fixes: 9e0d39d8a6 ("tpm: Remove useless priv field in struct tpm_vendor_specific")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkine <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-04-03 22:46:02 +03:00
Jerry Snitselaar 8569defde8 tpm_crb: check for bad response size
Make sure size of response buffer is at least 6 bytes, or
we will underflow and pass large size_t to memcpy_fromio().
This was encountered while testing earlier version of
locality patchset.

Cc: stable@vger.kernel.org
Fixes: 30fc8d138e ("tpm: TPM 2.0 CRB Interface")
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-04-03 22:46:02 +03:00
James Bottomley 4d57856a21 tpm2: add session handle context saving and restoring to the space code
Sessions are different from transient objects in that their handles
may not be virtualized (because they're used for some hmac
calculations).  Additionally when a session is context saved, a
vestigial memory remains in the TPM and if it is also flushed, that
will be lost and the session context will refuse to load next time, so
the code is updated to flush only transient objects after a context
save.  Add a separate array (chip->session_tbl) to save and restore
sessions by handle.  Use the failure of a context save or load to
signal that the session has been flushed from the TPM and we can
remove its memory from chip->session_tbl.

Sessions are also isolated during each instance of a tpm space.  This
means that spaces shouldn't be able to see each other's sessions and
is enforced by ensuring that a space user may only refer to sessions
handles that are present in their own chip->session_tbl.  Finally when
a space is closed, all the sessions belonging to it should be flushed
so the handles may be re-used by other spaces.

Note that if we get a session save or load error, all sessions are
effectively flushed.  Even though we restore the session buffer, all
the old sessions will refuse to load after the flush and they'll be
purged from our session memory.  This means that while transient
context handling is still soft in the face of errors, session handling
is hard (any failure of the model means all sessions are lost).

Fixes-from: Colin Ian King <colin.king@canonical.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-04-03 22:46:02 +03:00
James Bottomley fdc915f7f7 tpm: expose spaces via a device link /dev/tpmrm<n>
Currently the tpm spaces are not exposed to userspace.  Make this
exposure via a separate device, which can now be opened multiple times
because each read/write transaction goes separately via the space.

Concurrency is protected by the chip->tpm_mutex for each read/write
transaction separately.  The TPM is cleared of all transient objects
by the time the mutex is dropped, so there should be no interference
between the kernel and userspace.

Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-04-03 22:46:02 +03:00
James Bottomley ecb38e2f52 tpm: split out tpm-dev.c into tpm-dev.c and tpm-common-dev.c
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-04-03 22:46:01 +03:00
Jarkko Sakkinen 745b361e98 tpm: infrastructure for TPM spaces
Added an ability to virtualize TPM commands into an isolated context
that we call a TPM space because the word context is already heavily
used in the TPM specification. Both the handle areas and bodies (where
necessary) are virtualized.

The mechanism works by adding a new parameter struct tpm_space to the
tpm_transmit() function. This new structure contains the list of virtual
handles and a buffer of page size (currently) for backing storage.

When tpm_transmit() is called with a struct tpm_space instance it will
execute the following sequence:

1. Take locks.
2. Load transient objects from the backing storage by using ContextLoad
   and map virtual handles to physical handles.
3. Perform the transaction.
4. Save transient objects to backing storage by using ContextSave and
   map resulting physical handle to virtual handle if there is such.

This commit does not implement virtualization support for hmac and
policy sessions.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2017-04-03 22:46:01 +03:00
Jarkko Sakkinen 58472f5cd4 tpm: validate TPM 2.0 commands
Check for every TPM 2.0 command that the command code is supported and
the command buffer has at least the length that can contain the header
and the handle area.

For ContextSave and FlushContext we mark the body to be part of the
handle area. This gives validation for these commands at zero
cost, including the body of the command.

The more important reason for this is that we can virtualize these
commands in the same way as you would virtualize the handle area of a
command.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2017-04-03 22:46:01 +03:00
Jarkko Sakkinen 9aa36b399a tpm: export tpm2_flush_context_cmd
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2017-04-03 22:46:01 +03:00
Jarkko Sakkinen a147918e79 tpm: move length validation to tpm_transmit()
Check that the length matches the length reported by the response
header already in tpm_transmit() to improve validation.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2017-04-03 22:46:01 +03:00
Jarkko Sakkinen 38eb24ebb0 tpm_crb: encapsulate crb_wait_for_reg_32
Encapsulated crb_wait_for_reg32() so that state changes in other CRB
registers than TPM_CRB_CTRL_REQ_x can be waited.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Gang Wei <gang.wei@intel.com>
2017-04-03 22:46:01 +03:00
Jarkko Sakkinen 13b1f4a571 tpm_crb: map locality registers
In order to provide access to locality registers, this commits adds
mapping of the head of the CRB registers, which are located right
before the control area.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Gang Wei <gang.wei@intel.com>
2017-04-03 22:46:01 +03:00
Peter Huewe 5cc0101d1f tpm_tis_spi: Add small delay after last transfer
Testing the implementation with a Raspberry Pi 2 showed that under some
circumstances its SPI master erroneously releases the CS line before the
transfer is complete, i.e. before the end of the last clock. In this case
the TPM ignores the transfer and misses for example the GO command. The
driver is unable to detect this communication problem and will wait for a
command response that is never going to arrive, timing out eventually.

As a workaround, the small delay ensures that the CS line is held long
enough, even with a faulty SPI master. Other SPI masters are not affected,
except for a negligible performance penalty.

Cc: <stable@vger.kernel.org>
Fixes: 0edbfea537 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Benoit Houyere <benoit.houyere@st.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-04-03 22:46:01 +03:00
Peter Huewe 591e48c26c tpm_tis_spi: Remove limitation of transfers to MAX_SPI_FRAMESIZE bytes
Limiting transfers to MAX_SPI_FRAMESIZE was not expected by the upper
layers, as tpm_tis has no such limitation. Add a loop to hide that
limitation.

v2: Moved scope of spi_message to the top as requested by Jarkko
Cc: <stable@vger.kernel.org>
Fixes: 0edbfea537 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Benoit Houyere <benoit.houyere@st.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-04-03 22:46:01 +03:00
Peter Huewe e110cc69dc tpm_tis_spi: Check correct byte for wait state indicator
Wait states are signaled in the last byte received from the TPM in
response to the header, not the first byte. Check rx_buf[3] instead of
rx_buf[0].

Cc: <stable@vger.kernel.org>
Fixes: 0edbfea537 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Benoit Houyere <benoit.houyere@st.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-04-03 22:46:01 +03:00
Peter Huewe 975094ddc3 tpm_tis_spi: Abort transfer when too many wait states are signaled
Abort the transfer with ETIMEDOUT when the TPM signals more than
TPM_RETRY wait states. Continuing with the transfer in this state
will only lead to arbitrary failures in other parts of the code.

Cc: <stable@vger.kernel.org>
Fixes: 0edbfea537 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Benoit Houyere <benoit.houyere@st.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-04-03 22:46:01 +03:00
Peter Huewe f848f2143a tpm_tis_spi: Use single function to transfer data
The algorithm for sending data to the TPM is mostly identical to the
algorithm for receiving data from the TPM, so a single function is
sufficient to handle both cases.

This is a prequisite for all the other fixes, so we don't have to fix
everything twice (send/receive)

v2: u16 instead of u8 for the length.
Cc: <stable@vger.kernel.org>
Fixes: 0edbfea537 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Benoit Houyere <benoit.houyere@st.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-04-03 22:46:00 +03:00
Winkler, Tomas 095fc30c2c tpm/tpm_crb: enter the low power state upon device suspend
This fix enables a platform to enter the idle state (suspend-to-idle)

The driver needs to request explicitly go_idle upon completion
from the pm suspend handler.
The runtime pm is disabled on suspend during prepare state by calling
pm_runtime_get_noresume, hence we cannot relay on runtime pm to leave
the device in low power state. Symmetrically cmdReady is called
upon resume.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Siged-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-04-03 22:46:00 +03:00
Arnd Bergmann 4bf4b4ed9d tpm: select CONFIG_CRYPTO
We get a newly introduced harmless warning when CONFIG_CRYPTO is disabled:

warning: (TCG_TPM && TRUSTED_KEYS && IMA) selects CRYPTO_HASH_INFO which has unmet direct dependencies (CRYPTO)

This adds another select to avoid the warning, consistent with other users
of the crypto code.

Fixes: c1f92b4b04 ("tpm: enhance TPM 2.0 PCR extend to support multiple banks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-04-03 22:46:00 +03:00
Nayna Jain a233a0289c tpm: msleep() delays - replace with usleep_range() in i2c nuvoton driver
Commit 500462a9de "timers: Switch to a non-cascading wheel" replaced
the 'classic' timer wheel, which aimed for near 'exact' expiry of the
timers.  Their analysis was that the vast majority of timeout timers
are used as safeguards, not as real timers, and are cancelled or
rearmed before expiration.  The only exception noted to this were
networking timers with a small expiry time.

Not included in the analysis was the TPM polling timer, which resulted
in a longer normal delay and, every so often, a very long delay.  The
non-cascading wheel delay is based on CONFIG_HZ.  For a description of
the different rings and their delays, refer to the comments in
kernel/time/timer.c.

Below are the delays given for rings 0 - 2, which explains the longer
"normal" delays and the very, long delays as seen on systems with
CONFIG_HZ 250.

* HZ 1000 steps
 * Level Offset  Granularity            Range
 *  0      0         1 ms                0 ms - 63 ms
 *  1     64         8 ms               64 ms - 511 ms
 *  2    128        64 ms              512 ms - 4095 ms (512ms - ~4s)

* HZ  250
 * Level Offset  Granularity            Range
 *  0      0         4 ms                0 ms - 255 ms
 *  1     64        32 ms              256 ms - 2047 ms (256ms - ~2s)
 *  2    128       256 ms             2048 ms - 16383 ms (~2s - ~16s)

Below is a comparison of extending the TPM with 1000 measurements,
using msleep() vs. usleep_delay() when configured for 1000 hz vs. 250
hz, before and after commit 500462a9de.

linux-4.7 | msleep() usleep_range()
1000 hz: 0m44.628s | 1m34.497s 29.243s
250 hz: 1m28.510s | 4m49.269s 32.386s

linux-4.7  | min-max (msleep)  min-max (usleep_range)
1000 hz: 0:017 - 2:760s | 0:015 - 3:967s    0:014 - 0:418s
250 hz: 0:028 - 1:954s | 0:040 - 4:096s    0:016 - 0:816s

This patch replaces the msleep() with usleep_range() calls in the
i2c nuvoton driver with a consistent max range value.

Signed-of-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org (linux-4.8)
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-04-03 22:46:00 +03:00
Jason Gunthorpe b4e2eb0651 tpm crb: Work around BIOS's that report the wrong ACPI region size
The expectation is that the if the CRB cmd/rsp buffer falls within the
ACPI region that the entire buffer will be within the reason. Otherwise
resource reservation will fail when it crosses regions.

Work around this BIOS bug by limiting the cmd/rsp buffer to the length
of the declared ACPI region. BIOS vendors should fix this by making
the ACPI and register length declarations consistent.

Reported-by: Davide Guerri <davide.guerri@gmail.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Davide Guerri <davide.guerri@gmail.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-04-03 22:46:00 +03:00
Alexander Steffen 302a6ad7fc tpm_tis_core: Choose appropriate timeout for reading burstcount
TIS v1.3 for TPM 1.2 and PTP for TPM 2.0 disagree about which timeout
value applies to reading a valid burstcount. It is TIMEOUT_D according to
TIS, but TIMEOUT_A according to PTP, so choose the appropriate value
depending on whether we deal with a TPM 1.2 or a TPM 2.0.

This is important since according to the PTP TIMEOUT_D is much smaller
than TIMEOUT_A. So the previous implementation could run into timeouts
with a TPM 2.0, even though the TPM was behaving perfectly fine.

During tpm2_probe TIMEOUT_D will be used even with a TPM 2.0, because
TPM_CHIP_FLAG_TPM2 is not yet set. This is fine, since the timeout values
will only be changed afterwards by tpm_get_timeouts. Until then
TIS_TIMEOUT_D_MAX applies, which is large enough.

Cc: stable@vger.kernel.org
Fixes: aec04cbdf7 ("tpm: TPM 2.0 FIFO Interface")

Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-04-03 22:46:00 +03:00
Logan Gunthorpe 8dbbf58251 tpm-chip: utilize new cdev_device_add helper function
Replace the open coded registration of the cdev and dev with the
new device_add_cdev() helper. The helper replaces a common pattern by
taking the proper reference against the parent device and adding both
the cdev and the device.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-21 06:44:33 +01:00
Jarkko Sakkinen 61841be635 tpm: declare tpm2_get_pcr_allocation() as static
There's no need to export tpm2_get_pcr_alloation() because it is only
a helper function for tpm2_auto_startup(). For the same reason it does
not make much sense to maintain documentation for it.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-02-20 13:23:18 +02:00
Stefan Berger 51b0be640c tpm: Fix expected number of response bytes of TPM1.2 PCR Extend
The TPM1.2 PCR Extend operation only returns 20 bytes in the body,
which is the size of the PCR state.

This fixes a problem where IMA gets errors with every PCR Extend.

Fixes: c659af78eb ("tpm: Check size of response before accessing data")
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Acked-by: Mimi Zohar <zohar@us.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-02-15 20:09:52 +02:00
Julia Lawall 5cec5bacd3 tpm xen: drop unneeded chip variable
The call that used chip was dropped in 1f0f30e404.  Drop the
leftover declaration and initialization.

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-02-14 19:24:33 +02:00
Dmitry Torokhov 39f5712b8f tpm: fix misspelled "facilitate" in module parameter description
I typoed "facilitate" as "faciltate" a few years back...

Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-02-14 19:24:33 +02:00
Wei Yongjun 5939eaf4f9 tpm_tis: fix the error handling of init_tis()
Add the missing platform_driver_unregister() and remove the duplicate
platform_device_unregister(force_pdev) in the error handling case.

Fixes: 00194826e6 ("tpm_tis: Clean up the force=1 module parameter")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-02-14 19:24:33 +02:00
Dan Carpenter 70ea163699 tpm: silence an array overflow warning
We should check that we're within bounds first before checking that
"chip->active_banks[i] != TPM2_ALG_ERROR" so I've re-ordered the two
checks.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-02-03 22:33:55 +02:00
Stefan Berger a118cf2a5b tpm: fix the type of owned field in cap_t
In cap_t the size of the type bool is assumed to be one byte. This
commit sorts out the issue by changing the type to u8.

Fixes: c659af78eb ("tpm: Check size of response before accessing data")
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-02-03 22:03:14 +02:00
Nayna Jain 4d23cc323c tpm: add securityfs support for TPM 2.0 firmware event log
Unlike the device driver support for TPM 1.2, the TPM 2.0 does
not support the securityfs pseudo files for displaying the
firmware event log.

This patch enables support for providing the TPM 2.0 event log in
binary form. TPM 2.0 event log supports a crypto agile format that
records multiple digests, which is different from TPM 1.2. This
patch enables the tpm_bios_log_setup for TPM 2.0  and adds the
event log parser which understand the TPM 2.0 crypto agile format.

Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Kenneth Goldman <kgold@linux.vnet.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-02-03 22:03:14 +02:00
Nayna Jain e46e22f12b tpm: enhance read_log_of() to support Physical TPM event log
Physical TPMs use Open Firmware Device Tree bindings that are similar
to the IBM Power virtual TPM to support event log. However, these
properties store the values in different endianness for Physical
and Virtual TPM.

This patch fixes the endianness issue by doing appropriate conversion
based on Physical or Virtual TPM.

Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Kenneth Goldman <kgold@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-02-03 22:03:14 +02:00
Nayna Jain c1f92b4b04 tpm: enhance TPM 2.0 PCR extend to support multiple banks
The current TPM 2.0 device driver extends only the SHA1 PCR bank
but the TCG Specification[1] recommends extending all active PCR
banks, to prevent malicious users from setting unused PCR banks with
fake measurements and quoting them.

The existing in-kernel interface(tpm_pcr_extend()) expects only a
SHA1 digest.  To extend all active PCR banks with differing
digest sizes, the SHA1 digest is padded with trailing 0's as needed.

This patch reuses the defined digest sizes from the crypto subsystem,
adding a dependency on CRYPTO_HASH_INFO module.

[1] TPM 2.0 Specification referred here is "TCG PC Client Specific
Platform Firmware Profile for TPM 2.0"

Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Kenneth Goldman <kgold@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-02-03 22:03:14 +02:00
Nayna Jain 1db15344f8 tpm: implement TPM 2.0 capability to get active PCR banks
This patch implements the TPM 2.0 capability TPM_CAP_PCRS to
retrieve the active PCR banks from the TPM. This is needed
to enable extending all active banks as recommended by TPM 2.0
TCG Specification.

Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Kenneth Goldman <kgold@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-02-03 22:03:14 +02:00
Jarkko Sakkinen 7d761119a9 tpm: fix RC value check in tpm2_seal_trusted
The error code handling is broken as any error code that has the same
bits set as TPM_RC_HASH passes. Implemented tpm2_rc_value() helper to
parse the error value from FMT0 and FMT1 error codes so that these types
of mistakes are prevented in the future.

Fixes: 5ca4c20cfd ("keys, trusted: select hash algorithm for TPM2 chips")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
2017-02-03 22:03:14 +02:00
Maciej S. Szmigiero 419a16d9cd tpm_tis: fix iTPM probe via probe_itpm() function
probe_itpm() function is supposed to send command without an itpm flag set
and if this fails to repeat it, this time with the itpm flag set.

However, commit 41a5e1cf1f ("tpm/tpm_tis: Split tpm_tis driver into a
core and TCG TIS compliant phy") moved the itpm flag from an "itpm"
variable to a TPM_TIS_ITPM_POSSIBLE chip flag, so setting the
(now function-local) itpm variable no longer had any effect.

Finally, this function-local itpm variable was removed by
commit 56af322156 ("tpm/tpm_tis: remove unused itpm variable")

Tested only on non-iTPM TIS TPM.

Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-02-03 22:03:14 +02:00
Jason Gunthorpe fa2825da6f tpm: Begin the process to deprecate user_read_timer
For a long time the cdev read/write interface had this strange
idea that userspace had to read the result within 60 seconds otherwise
it is discarded. Perhaps this made sense under some older locking regime,
but in the modern kernel it is not required and is just dangerous.

Since something may be relying on this, double the timeout and print a
warning. We can remove the code in a few years, but this should be
enough to prevent new users.

Suggested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-02-03 22:03:14 +02:00
Jarkko Sakkinen 1d1915532b tpm: remove tpm_read_index and tpm_write_index from tpm.h
These are non-generic functions and do not belong to tpm.h.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
2017-02-03 22:03:14 +02:00
Stefan Berger c659af78eb tpm: Check size of response before accessing data
Make sure that we have not received less bytes than what is indicated
in the header of the TPM response. Also, check the number of bytes in
the response before accessing its data.

Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
2017-01-23 18:28:18 +02:00
Maciej S. Szmigiero 1d70fe9d9c tpm_tis: use default timeout value if chip reports it as zero
Since commit 1107d065fd ("tpm_tis: Introduce intermediate layer for
TPM access") Atmel 3203 TPM on ThinkPad X61S (TPM firmware version 13.9)
no longer works.  The initialization proceeds fine until we get and
start using chip-reported timeouts - and the chip reports C and D
timeouts of zero.

It turns out that until commit 8e54caf407 ("tpm: Provide a generic
means to override the chip returned timeouts") we had actually let
default timeout values remain in this case, so let's bring back this
behavior to make chips like Atmel 3203 work again.

Use a common code that was introduced by that commit so a warning is
printed in this case and /sys/class/tpm/tpm*/timeouts correctly says the
timeouts aren't chip-original.

Fixes: 1107d065fd ("tpm_tis: Introduce intermediate layer for TPM access")
Cc: stable@vger.kernel.org
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-01-23 18:28:18 +02:00
Jason Gunthorpe 62bfdacbac tpm: Do not print an error message when doing TPM auto startup
This is a regression when this code was reworked and made the error
print unconditional. The original code deliberately suppressed printing
of the first error message so it could quietly sense
TPM_ERR_INVALID_POSTINIT.

Fixes: a502feb67b47 ("tpm: Clean up reading of timeout and duration capabilities")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-01-23 18:28:18 +02:00
Jiandi An 19b7bf51fc tpm, tpm_crb: Handle 64-bit resource in crb_check_resource()
crb_check_resource() in TPM CRB driver calls
acpi_dev_resource_memory() which only handles 32-bit resources.
Adding a call to acpi_dev_resource_address_space() in TPM CRB
driver which handles 64-bit resources.

Signed-off-by: Jiandi An <anjiandi@codeaurora.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-01-23 18:28:18 +02:00
Geliang Tang aea7f54f3c tpm/tpm_tis_spi: drop duplicate header module.h
Drop duplicate header module.h from tpm_tis_spi.c.

Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-01-23 18:28:18 +02:00
Corentin Labbe 176cebc56b tpm/st33zp24: Remove unneeded linux/miscdevice.h include
tpm/st33zp24/st33zp24.c does not use any miscdevice so this patch remove
this unnecessary inclusion.

Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-01-23 18:28:18 +02:00
Winkler, Tomas 93c12f293f tpm/vtpm: fix kdoc warnings
Use corret kdoc format for function description and eliminate warning
of type:

tpm_ibmvtpm.c:66: warning: No description found for parameter 'count'

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-01-23 18:28:18 +02:00
Winkler, Tomas 2998b02b2f tmp: use pdev for parent device in tpm_chip_alloc
The tpm stack uses pdev name convention for the parent device.
Fix that also in tpm_chip_alloc().

Fixes: 3897cd9c8d ("tpm: Split out the devm stuff from tpmm_chip_alloc")'
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-01-23 18:28:18 +02:00
Winkler, Tomas 794c6e109b tpm/tpm2-chip: fix kdoc errors
Use correct kdoc format, describe correct parameters and return values.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-01-23 18:28:18 +02:00
Winkler, Tomas f865c19685 tpm: add kdoc for tpm_transmit and tpm_transmit_cmd
Functions tpm_transmit and transmit_cmd are referenced
from other functions kdoc hence deserve documentation.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-01-23 18:28:17 +02:00
Linus Torvalds a57cb1c1d7 Merge branch 'akpm' (patches from Andrew)
Merge more updates from Andrew Morton:

 - a few misc things

 - kexec updates

 - DMA-mapping updates to better support networking DMA operations

 - IPC updates

 - various MM changes to improve DAX fault handling

 - lots of radix-tree changes, mainly to the test suite. All leading up
   to reimplementing the IDA/IDR code to be a wrapper layer over the
   radix-tree. However the final trigger-pulling patch is held off for
   4.11.

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (114 commits)
  radix tree test suite: delete unused rcupdate.c
  radix tree test suite: add new tag check
  radix-tree: ensure counts are initialised
  radix tree test suite: cache recently freed objects
  radix tree test suite: add some more functionality
  idr: reduce the number of bits per level from 8 to 6
  rxrpc: abstract away knowledge of IDR internals
  tpm: use idr_find(), not idr_find_slowpath()
  idr: add ida_is_empty
  radix tree test suite: check multiorder iteration
  radix-tree: fix replacement for multiorder entries
  radix-tree: add radix_tree_split_preload()
  radix-tree: add radix_tree_split
  radix-tree: add radix_tree_join
  radix-tree: delete radix_tree_range_tag_if_tagged()
  radix-tree: delete radix_tree_locate_item()
  radix-tree: improve multiorder iterators
  btrfs: fix race in btrfs_free_dummy_fs_info()
  radix-tree: improve dump output
  radix-tree: make radix_tree_find_next_bit more useful
  ...
2016-12-14 17:25:18 -08:00
Matthew Wilcox 37f4915fef tpm: use idr_find(), not idr_find_slowpath()
idr_find_slowpath() is not intended to be part of the public API, it's
an implementation detail.  There's no reason to skip straight to the
slowpath here.

Link: http://lkml.kernel.org/r/1480369871-5271-64-git-send-email-mawilcox@linuxonhyperv.com
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Tested-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Peter Huewe <peterhuewe@gmx.de>
Cc: Marcel Selhorst <tpmdd@selhorst.net>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-12-14 16:04:10 -08:00
Linus Torvalds 683b96f4d1 Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull security subsystem updates from James Morris:
 "Generally pretty quiet for this release. Highlights:

  Yama:
   - allow ptrace access for original parent after re-parenting

  TPM:
   - add documentation
   - many bugfixes & cleanups
   - define a generic open() method for ascii & bios measurements

  Integrity:
   - Harden against malformed xattrs

  SELinux:
   - bugfixes & cleanups

  Smack:
   - Remove unnecessary smack_known_invalid label
   - Do not apply star label in smack_setprocattr hook
   - parse mnt opts after privileges check (fixes unpriv DoS vuln)"

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (56 commits)
  Yama: allow access for the current ptrace parent
  tpm: adjust return value of tpm_read_log
  tpm: vtpm_proxy: conditionally call tpm_chip_unregister
  tpm: Fix handling of missing event log
  tpm: Check the bios_dir entry for NULL before accessing it
  tpm: return -ENODEV if np is not set
  tpm: cleanup of printk error messages
  tpm: replace of_find_node_by_name() with dev of_node property
  tpm: redefine read_log() to handle ACPI/OF at runtime
  tpm: fix the missing .owner in tpm_bios_measurements_ops
  tpm: have event log use the tpm_chip
  tpm: drop tpm1_chip_register(/unregister)
  tpm: replace dynamically allocated bios_dir with a static array
  tpm: replace symbolic permission with octal for securityfs files
  char: tpm: fix kerneldoc tpm2_unseal_trusted name typo
  tpm_tis: Allow tpm_tis to be bound using DT
  tpm, tpm_vtpm_proxy: add kdoc comments for VTPM_PROXY_IOC_NEW_DEV
  tpm: Only call pm_runtime_get_sync if device has a parent
  tpm: define a generic open() method for ascii & bios measurements
  Documentation: tpm: add the Physical TPM device tree binding documentation
  ...
2016-12-14 13:57:44 -08:00
Jason Gunthorpe 9430066a15 tpm: adjust return value of tpm_read_log
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:33 +02:00
Jason Gunthorpe c4484f791c tpm: vtpm_proxy: conditionally call tpm_chip_unregister
If tpm_chip_register fails vtpm must not call tpm_chip_unregister:

> [   58.271017]  [<ffffffff8155bd32>] dpm_sysfs_remove+0x22/0x60
> [   58.271017]  [<ffffffff8154e438>] device_del+0x58/0x280
> [   58.271017]  [<ffffffffa024c020>] tpm_chip_unregister+0x40/0xb0 [tpm]
> [   58.271017]  [<ffffffffa0292360>] vtpm_proxy_fops_release+0x40/0x60 [tpm_vtpm_proxy]

[jarkko.sakkinen@linux.intel.com: cleaned up unneeded goto away]

Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:33 +02:00
Jason Gunthorpe 0cf577a03f tpm: Fix handling of missing event log
The event log is an optional firmware feature, if the firmware
does not support it then the securityfs files should not be created
and no other notification given.

- Uniformly return -ENODEV from the tpm_bios_log_setup cone if
  no event log is detected.
- Check in ACPI if this node was discovered via ACPI.
- Improve the check in OF to make sure there is a parent and to
  fail detection if the two log properties are not declared
- Pass through all other error codes instead of filtering just some

Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:32 +02:00
Stefan Berger 005451d44a tpm: Check the bios_dir entry for NULL before accessing it
Check the bios_dir entry for NULL before accessing it. Currently
this crashes the driver when a TPM 2 is attached and the entries
are NULL.

Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:32 +02:00
Colin Ian King 79eec5b940 tpm: return -ENODEV if np is not set
device_node np contains a garbage value from the stack and it
is only set if chip->dev.parent->of_node is not null.  Thus the
check for a null np won't spot a garbage value of np from the
stack if chip->dev.parent->of_node is null and if np contains
an garbage non-null value.

I believe the correct fix is to return -ENODEV if and only if
chip->dev.parent->of_node is null.

Found with static analysis by CoverityScan, CID 1377755

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:32 +02:00
Nayna Jain 5efae7d6b0 tpm: cleanup of printk error messages
This patch removes the unnecessary error messages on failing to
allocate memory and replaces pr_err/printk with dev_dbg/dev_info
as applicable.

Suggested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:32 +02:00
Nayna Jain ed4fdb4f5d tpm: replace of_find_node_by_name() with dev of_node property
Using the device of_node property is a better way to refer to the
device tree node rather than of_find_node_by_name().

Suggested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:32 +02:00
Nayna Jain 02ae138288 tpm: redefine read_log() to handle ACPI/OF at runtime
Currently, read_log() has two implementations: one for ACPI platforms
and the other for device tree(OF) based platforms. The proper one is
selected at compile time using Kconfig and #ifdef in the Makefile,
which is not the recommended approach.

This patch removes the #ifdef in the Makefile by defining a single
read_log() method, which checks for ACPI/OF event log properties at
runtime.

[jarkko.sakkinen@linux.intel.com: added tpm_ prefix to read_log*]

Suggested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:32 +02:00
Nayna Jain f40e68ef4a tpm: fix the missing .owner in tpm_bios_measurements_ops
This patch fixes the missing .owner field in
tpm_bios_measurements_ops definition.

Suggested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:32 +02:00
Nayna Jain 748935eeb7 tpm: have event log use the tpm_chip
Move the backing memory for the event log into tpm_chip and push
the tpm_chip into read_log. This optimizes read_log processing by
only doing it once and prepares things for the next patches in the
series which require the tpm_chip to locate the event log via
ACPI and OF handles instead of searching.

This is straightfoward except for the issue of passing a kref through
i_private with securityfs. Since securityfs_remove does not have any
removal fencing like sysfs we use the inode lock to safely get a
kref on the tpm_chip.

Suggested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:32 +02:00
Jarkko Sakkinen 7518a21a9d tpm: drop tpm1_chip_register(/unregister)
Check for TPM2 chip in tpm_sysfs_add_device, tpm_bios_log_setup and
tpm_bios_log_teardown in order to make code flow cleaner and to enable
to implement TPM 2.0 support later on. This is partially derived from
the commit by Nayna Jain with the extension that also tpm1_chip_register
is dropped.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Nayna Jain <nayna@linux.vnet.ibm.com>
2016-11-28 01:31:32 +02:00
Jarkko Sakkinen cd9b7631a8 tpm: replace dynamically allocated bios_dir with a static array
This commit is based on a commit by Nayna Jain. Replaced dynamically
allocated bios_dir with a static array as the size is always constant.

Suggested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:31 +02:00
Nayna Jain b1a9b7b602 tpm: replace symbolic permission with octal for securityfs files
checkpatch.pl flags warning for symbolic permissions and suggests
to replace with octal value.

This patch changes securityfs pseudo files permission
to octal values in tpm_bios_log_setup().

Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:31 +02:00
Baruch Siach cbef69a9e1 char: tpm: fix kerneldoc tpm2_unseal_trusted name typo
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:31 +02:00
Jason Gunthorpe 420d439849 tpm_tis: Allow tpm_tis to be bound using DT
This provides an open firwmare driver binding for tpm_tis. OF
is useful on arches where ACPI/PNP is not used.

The tcg,tpm-tis-mmio register map interface is specified by the TCG.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:31 +02:00
Jarkko Sakkinen 7ea7861c8c tpm, tpm_vtpm_proxy: add kdoc comments for VTPM_PROXY_IOC_NEW_DEV
Added kdoc comments for VTPM_PROXY_IOC_NEW_DEV so that these can be
imported to the kernel documentation written with rst markup and
generated with Sphinx.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
2016-11-28 01:31:31 +02:00
Stefan Berger 6804f6bba0 tpm: Only call pm_runtime_get_sync if device has a parent
Only call pm_runtime_get_sync if the device has a parent. This
change fixes a crash in the tpm_vtpm_proxy driver since that
driver does not have a parent device.

Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:31 +02:00
Nayna Jain 2528a64664 tpm: define a generic open() method for ascii & bios measurements
open() method for event log ascii and binary bios measurements file
operations are very similar. This patch refactors the code into a
single open() call by passing seq_operations as i_node->private data.

Suggested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:31 +02:00
Jason Gunthorpe 1a277e674b tpm: Get rid of TPM_CHIP_FLAG_REGISTERED
This is no longer necessary, all calls to tpm_chip_unregister happen
in remove() callbacks.

Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:31 +02:00
Jason Gunthorpe 1f0f30e404 tpm xen: Remove bogus tpm_chip_unregister
tpm_chip_unregister can only be called after tpm_chip_register.
devm manages the allocation so no unwind is needed here.

Cc: stable@vger.kernel.org
Fixes: afb5abc262 ("tpm: two-phase chip management functions")
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:30 +02:00
Jason Gunthorpe d1d253cff7 tpm tis: Do not print timeout messages twice
The tis driver does a tpm_get_timeouts out side of tpm_chip_register,
and tpm_get_timeouts can print a message, resulting in two prints, eg:

 tpm tpm0: [Hardware Error]: Adjusting reported timeouts: A 10000->750000us B 10000->2000000us C 10000->750000us D 10000->750000us

Keep track and prevent tpm_get_timeouts from running a second time, and
clarify the purpose of the call in tpm_tis_core to only be connected to
irq testing.

Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:30 +02:00
Josh Zimmerman 26a137e31f tpm_tis: Check return values from get_burstcount.
If the TPM we're connecting to uses a static burst count, it will report
a burst count of zero throughout the response read. However, get_burstcount
assumes that a response of zero indicates that the TPM is not ready to
receive more data. In this case, it returns a negative error code, which
is passed on to tpm_tis_{write,read}_bytes as a u16, causing
them to read/write far too many bytes.

This patch checks for negative return codes and bails out from recv_data
and tpm_tis_send_data.

Cc: stable@vger.kernel.org
Fixes: 1107d065fd (tpm_tis: Introduce intermediate layer for TPM access)
Signed-off-by: Josh Zimmerman <joshz@google.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:30 +02:00
Winkler, Tomas ca6d458022 tpm: place kdoc just above tpm_pcr_extend
Place kdoc just above tpm_pcr_extend so it can be parsed correctly.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:30 +02:00
Jarkko Sakkinen 84fda15286 tpm: sanitize constant expressions
Use cpu_to_b32 at the time it is needed in enum tpm_capabilities and
enum tpm_sub_capabilities in order to be consistent with the other
enums in drivats/char/tpm/tpm.h.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:30 +02:00
Ed Swierk aaa6f7f6c8 tpm: Clean up reading of timeout and duration capabilities
Call tpm_getcap() from tpm_get_timeouts() to eliminate redundant
code. Return all errors to the caller rather than swallowing them
(e.g. when tpm_transmit_cmd() returns nonzero).

Signed-off-by: Ed Swierk <eswierk@skyportsystems.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:30 +02:00
Peter Huewe 2c97f6f20c char/tpm: Check return code of wait_for_tpm_stat
In some weird cases it might be possible that the TPM does not set
STS.VALID within the given timeout time (or ever) but sets STS.EXPECT
(STS=0x0C) In this case the driver gets stuck in the while loop of
tpm_tis_send_data and loops endlessly.

Checking the return value of wait_for_tpm_stat fixes this and the driver
bails out correctly.  While at it fixing all other users since if the
TPM does not manage to set STS.VALID within the reasonable timeframe
something is definitely wrong and the driver should react correctly.

Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:30 +02:00
Winkler, Tomas e74f2f76c1 tmp/tpm_crb: implement runtime pm for tpm_crb
Utilize runtime_pm for driving tpm crb idle states.
The framework calls cmd_ready from the pm_runtime_resume handler
and go idle from the pm_runtime_suspend handler.
The TPM framework should wake the device before transmit and receive.
In case the runtime_pm framework is not compiled in or enabled, the device
will be in the permanent ready state.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:30 +02:00
Winkler, Tomas c58bd34cec tpm/tpm_crb: open code the crb_init into acpi_add
This is preparation step for implementing tpm crb
runtime pm. We need to have tpm chip allocated
and populated before we access the runtime handlers.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:30 +02:00
Winkler, Tomas bc33c5df71 tmp/tpm_crb: fix Intel PTT hw bug during idle state
There is a HW bug in Skylake, and Broxton PCH Intel PTT device, where
most of the registers in the control area except START, REQUEST, CANCEL,
and LOC_CTRL lost retention when the device is in the idle state. Hence
we need to bring the device to ready state before accessing the other
registers. The fix brings device to ready state before trying to read
command and response buffer addresses in order to remap the for access.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinn@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinn@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:29 +02:00
Winkler, Tomas ba5287b6ef tpm/tpm_crb: implement tpm crb idle state
The register TPM_CRB_CTRL_REQ_x contains bits goIdle and cmdReady for
SW to indicate that the device can enter or should exit the idle state.

The legacy ACPI-start (SMI + DMA) based devices do not support these
bits and the idle state management is not exposed to the host SW.
Thus, this functionality only is enabled only for a CRB start (MMIO)
based devices.

Based on Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
original patch:
'tpm_crb: implement power tpm crb power management'

To keep the implementation local to the hw we don't use wait_for_tpm_stat
for polling the TPM_CRB_CTRL_REQ.

[jarkko.sakkinen@linux.intel.com: removed cmdReady debug trace on a
 success case due the heavy amount of log traffic it causes.]

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:29 +02:00
Juergen Gross 0240933469 xen: make use of xenbus_read_unsigned() in xen-tpmfront
Use xenbus_read_unsigned() instead of xenbus_scanf() when possible.
This requires to change the type of one read from int to unsigned,
but this case has been wrong before: negative values are not allowed
for the modified case.

Cc: peterhuewe@gmx.de
Cc: tpmdd@selhorst.net
Cc: jarkko.sakkinen@linux.intel.com
Cc: jgunthorpe@obsidianresearch.com
Cc: tpmdd-devel@lists.sourceforge.net

Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
2016-11-07 13:55:11 +01:00
Jarkko Sakkinen befd99656c tpm: remove invalid min length check from tpm_do_selftest()
Removal of this check was not properly amended to the original commit.

Cc: stable@vger.kernel.org
Fixes: 0c54133223 ("tpm: use tpm_pcr_read_dev() in tpm_do_selftest()")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
2016-10-31 09:15:27 -06:00
Jarkko Sakkinen 324152502b Revert "tpm/tpm_crb: implement tpm crb idle state"
This reverts commit e17acbbb69.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-09-27 12:02:13 +03:00
Jarkko Sakkinen cfa1882203 Revert "tmp/tpm_crb: fix Intel PTT hw bug during idle state"
This reverts commit 9514ff1961.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-09-27 12:01:43 +03:00
Jarkko Sakkinen 2b7926ae1c Revert "tpm/tpm_crb: open code the crb_init into acpi_add"
This reverts commit 0c22db435b.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-09-27 12:01:25 +03:00
Jarkko Sakkinen 4886cd80cb Revert "tmp/tpm_crb: implement runtime pm for tpm_crb"
This reverts commit e350e24694.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-09-27 12:00:13 +03:00
Winkler, Tomas e350e24694 tmp/tpm_crb: implement runtime pm for tpm_crb
Utilize runtime_pm for driving tpm crb idle states.
The framework calls cmd_ready from the pm_runtime_resume handler
and go idle from the pm_runtime_suspend handler.
The TPM framework should wake the device before transmit and receive.
In case the runtime_pm framework is not enabled, the device will be in
ready state.

[jarkko.sakkinen@linux.intel.com: changed pm_runtime_put_sync()
 to pm_runtime_put()]

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-09-16 15:51:22 +03:00
Winkler, Tomas 0c22db435b tpm/tpm_crb: open code the crb_init into acpi_add
This is preparation step for implementing tpm crb
runtime pm. We need to have tpm chip allocated
and populated before we access the runtime handlers.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinn@linux.intel.com>
2016-09-16 15:47:52 +03:00
Winkler, Tomas 9514ff1961 tmp/tpm_crb: fix Intel PTT hw bug during idle state
There is a HW bug in Skylake, and Broxton PCH Intel PTT device, where
most of the registers in the control area except START, REQUEST, CANCEL,
and LOC_CTRL lost retention when the device is in the idle state. Hence
we need to bring the device to ready state before accessing the other
registers. The fix brings device to ready state before trying to read
command and response buffer addresses in order to remap the for access.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinn@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinn@linux.intel.com>
2016-09-16 15:47:45 +03:00
Winkler, Tomas e17acbbb69 tpm/tpm_crb: implement tpm crb idle state
The register TPM_CRB_CTRL_REQ_x contains bits goIdle and cmdReady for
SW to indicate that the device can enter or should exit the idle state.

The legacy ACPI-start (SMI + DMA) based devices do not support these
bits and the idle state management is not exposed to the host SW.
Thus, this functionality only is enabled only for a CRB start (MMIO)
based devices.

Based on Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
original patch:
'tpm_crb: implement power tpm crb power management'

To keep the implementation local to the hw we don't use wait_for_tpm_stat
for polling the TPM_CRB_CTRL_REQ.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-09-16 15:47:36 +03:00
Jarkko Sakkinen ebfd7532e9 tpm: add check for minimum buffer size in tpm_transmit()
tpm_transmit() does not check that bufsiz is at least TPM_HEADER_SIZE
before accessing data. This commit adds this check and returns -EINVAL
if it fails.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-09-15 16:04:21 +03:00
Julia Lawall 0014777f98 tpm: constify TPM 1.x header structures
Constify TPM 1.x header structures in order to move them to rodata
section as they are meant to be never changed during runtime.

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-09-15 16:04:21 +03:00
Tomas Winkler 64fba530e9 tpm/tpm_crb: fix the over 80 characters checkpatch warring
Because of the line break in the debug print the chackpatch is
not silent on 80 characters limitation.

The easiest fix is to straighten the lines, it's also more readable.

WARNING: line over 80 characters
+                       FW_BUG "TPM2 ACPI table does not define a memory
resource\n");

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-09-15 16:04:21 +03:00
Tomas Winkler 47de683afa tpm/tpm_crb: drop useless cpu_to_le32 when writing to registers
Don't apply endianity conversion when writing to the registers
this is already handled by the system.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-09-15 16:04:21 +03:00
Tomas Winkler aa77ea0e43 tpm/tpm_crb: cache cmd_size register value.
Instead of expensive register access on retrieving cmd_size
on each send, save the value during initialization in the private
context. The value doesn't change.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-09-15 16:04:21 +03:00
Tomas Winkler 71801310b1 tmp/tpm_crb: drop include to platform_device
The platform device is not used in this driver, drop the
include to linux/platform_device.h

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-09-15 16:04:21 +03:00
Tomas Winkler 56af322156 tpm/tpm_tis: remove unused itpm variable
Fixes the warning:
drivers/char/tpm/tpm_tis_core.c:443:7: warning: variable ‘itpm’ set but
not used [-Wunused-but-set-variable]
  bool itpm;
       ^~~~

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-09-15 16:04:21 +03:00
Jarkko Sakkinen f39a9e97d7 tpm_crb: fix incorrect values of cmdReady and goIdle bits
CRB_CTRL_CMD_READY and CRB_CTRL_GO_IDLE have incorrect values.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-09-15 16:04:21 +03:00
Jarkko Sakkinen 7fd10d6185 tpm_crb: refine the naming of constants
Renamed CRB protocol specific constants to match the TCG PC Client
Platform TPM Profile (PTP) Specification and driver status constants
to be explicit that they are driver specific.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-09-15 16:04:21 +03:00
Jarkko Sakkinen 35fec6f1eb tpm_crb: remove wmb()'s
wmb()'s are not needed as iowrite32() is used.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-09-15 16:04:21 +03:00
Jarkko Sakkinen 72fd50e14e tpm_crb: fix crb_req_canceled behavior
The req_canceled() callback is used by tpm_transmit() periodically to
check whether the request has been canceled while it is receiving a
response from the TPM.

The TPM_CRB_CTRL_CANCEL register was cleared already in the crb_cancel
callback, which has two consequences:

* Cancel might not happen.
* req_canceled() always returns zero.

A better place to clear the register is when starting to send a new
command. The behavior of TPM_CRB_CTRL_CANCEL is described in the
section 5.5.3.6 of the PTP specification.

CC: stable@vger.kernel.org
Fixes: 30fc8d138e ("tpm: TPM 2.0 CRB Interface")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-09-15 16:04:21 +03:00
Jarkko Sakkinen 0c54133223 tpm: use tpm_pcr_read_dev() in tpm_do_selftest()
Instead of a ad-hoc protocol message construction it is better to
call tpm_pcr_read_dev().

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
2016-09-15 16:04:21 +03:00
Jarkko Sakkinen ae7e190a3e tpm: use tpm_transmit_cmd() in tpm2_probe()
It is better to tpm_transmit_cmd() in tpm2_probe() in order to get
consistent command handling throughout the subsystem.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
2016-09-15 16:04:21 +03:00
Jarkko Sakkinen eb5854e764 tpm: replace tpm_gen_interrupt() with tpm_tis_gen_interrupt()
Since tpm_gen_interrupt() is only used in tpm_tis_core.c this commit
replaces it with an internal tpm_tis_gen_interrupt(). The semantics
also changed in a way that on a system error the driver initialization
is failed.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
2016-09-15 16:04:21 +03:00
Jarkko Sakkinen d4abd9565d tpm: remove unnecessary externs from tpm.h
Removed unnecessary externs from tpm.h.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
2016-09-15 16:04:21 +03:00