Commit 6e532afaca ("mtd: nand: atmel: Add PM ops") started to use the
nand_reset() function which was not yet exported by the NAND framework
(because it was only used internally before that). Export this symbol
to avoid build errors when the driver is enabled as a module.
Fixes: 6e532afaca ("mtd: nand: atmel: Add PM ops")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
According to the datasheet, the HW sequencer has a predefined list
of opcodes, with only the erase opcode being programmable in LVSCC
and UVSCC registers. If these registers don't contain a valid erase
opcode (eg: BIOS does not program it), erase cannot be done using
the HW sequencer, even though the erase operation does not report
any error, the flash remains not erased.
If such register setting is detected, let's fall back to use the SW
sequencer to erase instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
The ispi->swseq is used for register access. Let's rename it to
swseq_reg to better describe its usage.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
There is no code that alters the HSFSTS register content in between
in intel_spi_write(). Remove the unnecessary RW to save some cycles.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
At present the driver relies on valid OPMENU0/OPMENU1 register values
that are programmed by BIOS to function correctly. However in a real
world it's absolutely legitimate for a bootloader to leave these two
registers untouched. Intel FSP for Baytrail exactly does like this.
When we are booting from any Intel FSP based bootloaders like U-Boot,
the driver refuses to work.
We can of course program various flash opcodes in the OPMENU0/OPMENU1
registers, and such workaround can be added in either the bootloader
codes, or the kernel driver itself.
But a graceful solution would be to update the kernel driver to remove
such limitation of OPMENU0/1 register dependency. The SPI controller
settings are not locked under such configuration. So we can first check
the controller locking status, and if it is not locked that means the
driver job can be fulfilled by using a chosen OPMENU index to set up
the flash opcode every time.
While we are here, the missing 'Atomic Cycle Sequence' handling in the
SW sequencer codes is also added.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
So far intel_spi_write() uses the HW sequencer to do the write. But
the HW sequencer register HSFSTS_CTL does not have such a field for
'Atomic Cycle Sequence', remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Baytrail/Lynx Point SPI controller's HW sequencer only supports basic
operations. This is determined by the chipset design, however current
codes try to use register values in OPMENU0/OPMENU1 to see whether SW
sequencer should be used, which is wrong. In fact OPMENU0/OPMENU1 can
remain unprogrammed by some bootloaders.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Intel SPI controller only has a 64 bytes FIFO. This adds a sanity
check before triggering any HW/SW sequencer work.
Additionally for the SW sequencer, if given data length is zero,
we should not mark the 'Data Cycle' bit.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
There are two bugs in current intel_spi_sw_cycle():
- The 'data byte count' field should be the number of bytes
transferred minus 1
- SSFSTS_CTL is the offset from ispi->sregs, not ispi->base
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Cc: <stable@vger.kernel.org> # v4.11+
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
intel_spi_hw_cycle() and intel_spi_sw_cycle() don't use the parameter
'buf' at all. Remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
The number of protected range registers is not the same on BYT/LPT/
BXT. GPR0 only exists on Apollo Lake and its offset is reserved on
other platforms.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Intel Cedar Fork has the same SPI serial flash controller than Intel
Denverton. Add the Intel Cedar Fork PCI ID to the driver list of
supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Intel Lewisburg chipset exposes the SPI serial flash controller as a PCI
device in the same way than Intel Denverton. Add Intel Lewisburg SPI
serial flash PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Tested against GD25LQ32D but the GD25LQ32C datasheet seems to be
identically feature-wise. Therefore dropping the suffix as it's
probably only indicating the die revision.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Add support for GD25Q256, a 32MiB SPI Nor flash
from GigaDevice.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Some manufacturers may use different bit to set QE on different
memories.
The GD25Q256 from GigaDevice is an example, which uses S6(bit 6
of the Status Register-1) to set QE, which is different with
other supported memories from GigaDevice that use S9(bit 1 of
the Status Register-2). This makes it is impossible to select
the quad enable method by distinguishing the MFR. This patch
introduce a quad_enable function which can be set per memory
in the flash_info list table.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Allow ARM64 support for the Cadence QSPI interface by
adding ARM64 as a dependency.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Implemented and populated spi-nor mtd PM handlers for resume ops.
spi-nor resume op re-initializes spi-nor flash to its probed
state by calling the newly implemented spi_nor_init() function.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
This patch extracts some chunks from spi_nor_init_params and spi_nor_scan()
and moves them into a new spi_nor_init() function.
Indeed, spi_nor_init() regroups all the required SPI flash commands to be
sent to the SPI flash memory before performing any runtime operations
(Fast Read, Page Program, Sector Erase, ...). Hence spi_nor_init():
1) removes the flash protection if applicable for certain vendors.
2) sets the Quad Enable bit, if needed, before using Quad SPI protocols.
3) makes the memory enter its (stateful) 4-byte address mode, if needed,
for SPI flash memory > 128Mbits not supporting the 4-byte address
instruction set.
spi_nor_scan() now ends by calling spi_nor_init() once the probe phase has
completed. Further patches could also use spi_nor_init() to implement the
mtd->_resume() handler for the spi-nor framework.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
header.minor is of type u8 and cannot be negative.
Detected by CoverityScan CID#1417858 ("Integer handling issues")
Fixes: f384b352cb ("mtd: spi-nor: parse Serial Flash Discoverable
Parameters (SFDP) tables")
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Marvell recent SoCs like A7k/A8k do not boot with NAND flash
controller activated by default. Enabling the controller is a matter of
writing in a system controller register that may also be used for other
NAND related choices.
This change is needed to stay bootloader independent.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Use the of_device_get_match_data() helper instead of open coding.
While at it, make config const so the cast can be dropped.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The WE_2_RE register specifies the number of clock cycles inserted
between the rising edge of #WE and the falling edge of #RE.
The current setup_data_interface implementation takes care of tWHR,
but tCCS is missing. Wait for max(tCSS, tWHR) to meet the spec.
With setup_data_interface() properly programmed, the Denali NAND
controller can observe the timing, so NAND_WAIT_TCCS flag is unneeded.
Clarify this in the comment block.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
More and more SoCs use the pxa3xx_nand driver for their controller but
the list of them was not updated. This patch add the last SoCs using the
driver.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
During backup mode, the contents of all registers will be cleared as the
SoC will be completely powered down. For a product that boots on NAND
Flash memory, the bootloader will obviously use the related controller
to read the Flash and correct any detected error in the memory, before
handling back control to the kernel's resuming entry point.
But it does not clean the NAND controller registers after use and on its
side the kernel driver expects the error locator to be powered down and
in a clean state. Add a resume hook for the PMECC error locator, and
reset its registers.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
1. Add the function for command descriptor preparation which will
be used only by BAM DMA and it will form the DMA descriptors
containing command elements
2. DMA_PREP_CMD flag should be used for forming command DMA
descriptors
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
All the QPIC register read/write through BAM DMA requires
command descriptor which contains the array of command elements.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
There is exactly one board in the kernel that defines platform data
for the GPIO NAND driver.
Use the feature to provide a lookup table for the GPIOs in the board
file so we can convert the driver as a whole to just use GPIO
descriptors.
After this we can cut the use of <linux/of_gpio.h> and use the GPIO
descriptor management from <linux/gpio/consumer.h> alone to grab and use
the GPIOs used in the driver.
I also created a local struct device *dev in the probe() function
because I was getting annoyed with all the &pdev->dev dereferencing.
Cc: arm@kernel.org
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Frans Klaver <fransklaver@gmail.com>
Cc: Gerhard Sittig <gsi@denx.de>
Cc: Jamie Iles <jamie.iles@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Jamie Iles <jamie.iles@oracle.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
When calculating the size needed by struct atmel_pmecc_user *user,
the dmu and delta buffer sizes were forgotten.
This lead to a memory corruption (especially with a large ecc_strength).
Link: http://lkml.kernel.org/r/1506503157.3016.5.camel@gmail.com
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Cc: stable@vger.kernel.org
Reported-by: Richard Genoud <richard.genoud@gmail.com>
Pointed-at-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Commit 1eeef2d748 ("mtd: handle partitioning on devices with 0
erasesize") introduced a regression on heterogeneous erase region
devices. Alignment of the partition was tested against the master
eraseblock size which can be bigger than the slave one, thus leading
to some partitions being marked as read-only.
Update wr_alignment to match this slave erasesize after this erasesize
has been determined by picking the biggest erasesize of all the regions
embedded in the MTD partition.
Reported-by: Mathias Thore <Mathias.Thore@infinera.com>
Fixes: 1eeef2d748 ("mtd: handle partitioning on devices with 0 erasesize")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Mathias Thore <Mathias.Thore@infinera.com>
Reviewed-by: Mathias Thore <Mathias.Thore@infinera.com>
The previous commit added some hooks into struct denali_nand_info,
so here is one more for clean-up.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The Denali NAND IP core decodes the lower 28 bits of the slave address
to get the control information; bit[27:26]=mode, bit[25:24]=bank, etc.
This means 256MB address range must be allocated for this IP. (Direct
Addressing)
For systems with address space limitation, the Denali IP provides an
optional module that translates the addressing - address and data are
latched by the registers in the translation module. (Indexed Addressing)
The addressing mode can be selected when the delivered RTL is configured,
and it can be read out from the FEATURES register.
Most of SoC vendors would choose Indexed Addressing to save the address
space, but Direct Addressing is possible as well, and it can be easily
supported by adding ->host_{read,write} hooks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The ECC correction is properly enabled/disabled before the page
read/write. There is no need to set up this at the beginning of
the probe.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
I used (uint64_t) cast to avoid "right shift count >= width of type"
warning. <linux/kernel.h> provides nice helpers to cater to it.
The code will be cleaner, and easier to understand.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This driver explains too much about what is apparent from the code.
Comments around basic APIs such as init_completion(), spin_lock_init(),
etc. seem unneeded lessons to kernel developers.
(With those comments dropped, denali_drv_init() is small enough,
so it has been merged into the probe function.)
Also, NAND driver developers should know the NAND init procedure, so
there is no need to explain nand_scan_ident/tail.
I removed FSF's address from the license blocks, and added simple
comments to struct members.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
In several places in this driver, the register fields are retrieved
as follows:
val = reg & FOO_MASK;
Then, modified as follows:
reg &= ~FOO_MASK;
reg |= val;
This code relies on its shift is 0, which we will never know until
we check the definition of FOO_MASK. Use FIELD_PREP / FIELD_GET
where appropriate.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
All the register offsets and bitfield masks are defined in denali.h,
but the driver code ended up with additional crappy macros such as
MAKE_ECC_CORRECTION(), ECC_SECTOR(), etc.
The reason is apparent - accessing a register field requires mask and
shift pair. The denali.h only provides mask. However, defining both
is tedious.
<linux/bitfield.h> provides a convenient way to get register fields
only with a single shifted mask. Now use it.
While I am here, I shortened some macros.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This function has a local variable "irq_mask" and its value is
the same as denali->irq_mask. Clean up the code a little.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This helper just sets/clears a flag of DMA_ENABLE register (with
register read-back, I do not know why it is necessary).
Move the register write code to the caller, and remove the helper.
It works for me without the register read-back.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Include necessary headers explicitly without relying on indirect
header inclusion. Also, sort them alphabetically.
<linux/delay.h>, <linux/wait.h>, <linux/mutex.h> turned out bogus,
so removed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
All functions in this driver are prefixed with denali_
except detect_max_banks(). Rename it for consistency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The setup_ecc_for_xfer() is only called from denali_data_xfer().
This helper is small enough, so squash it into the caller.
This looks cleaner to me.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The register TWO_ROW_ADDR_CYCLES specifies the number of row address
cycles of the device, but it is fixed to 0 in the driver init code
(i.e. always 3 row address cycles).
Reflect the result of nand_scan_ident() to the register setting
in order to support 2 row address cycle devices.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Several drivers check ->chipsize to see if the third row address cycle
is needed. Instead of embedding magic sizes such as 32MB, 128MB in
drivers, introduce a new flag NAND_ROW_ADDR_3 for clean-up. Since
nand_scan_ident() knows well about the device, it can handle this
properly. The flag is set if the row address bit width is greater
than 16.
Delete comments such as "One more address cycle for ..." because
intention is now clear enough from the code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Use the core's large page OOB layout functions when not reserving any
space for ECC bytes in the OOB layout. Fix ->nand_ooblayout_ecc_lp()
to return -ERANGE instead of a zero length in this case.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This patch fix the following build warning:
drivers/mtd/nand/nand_base.c:2671:30: attention : variable ‘blockmask’ set but not used [-Wunused-but-set-variable]
Fixes: 0b4773fd16 ("mtd: nand: Drop unused cached programming support")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
If 'clk_prepare_enable()' fails, we must 'put' the corresponding clock.
Fixes: 4d26f012ab ("mtd: nand: lpc32xx_mlc: Handle return value of clk_prepare_enable.")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
spi_nor_read_sfdp() calls nor->read() to read the SFDP data.
When the m25p80 driver is used (pretty common case), nor->read() is then
implemented by the m25p80_read() function, which is likely to initialize a
'struct spi_transfer' from its buf argument before appending this
structure inside the 'struct spi_message' argument of spi_sync().
Besides the SPI sub-system states that both .tx_buf and .rx_buf members of
'struct spi_transfer' must point into dma-safe memory. However, two of the
three calls of spi_nor_read_sfdp() were given pointers to stack allocated
memory as buf argument, hence not in a dma-safe area.
Hopefully, the third and last call of spi_nor_read_sfdp() was already
given a kmalloc'ed buffer argument, hence dma-safe.
So this patch fixes this issue by introducing a
spi_nor_read_sfdp_dma_unsafe() function which simply wraps the existing
spi_nor_read_sfdp() function and uses some kmalloc'ed memory as a bounce
buffer.
Fixes: f384b352cb ("mtd: spi-nor: parse Serial Flash Discoverable Parameters (SFDP) tables")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
One field of the flash parameter table contains information about the
flash device size.
Most of the time the data extracted from this field is valid, but
sometimes the BFPT section of the SFDP table is corrupted or invalid and
this field is set to 0xffffffff, thus resulting in an integer overflow
when setting params->size.
Since NOR devices are anayway always smaller than 2^64 bytes, we can
easily stop the BFPT parsing if the size reported in this table is
invalid.
Fixes: f384b352cb ("mtd: spi-nor: parse Serial Flash Discoverable Parameters (SFDP) tables")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.com>
- Minor improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=gwDT
-----END PGP SIGNATURE-----
Merge tag 'upstream-4.14-rc1' of git://git.infradead.org/linux-ubifs
Pull UBI updates from Richard Weinberger:
"Minor improvements"
* tag 'upstream-4.14-rc1' of git://git.infradead.org/linux-ubifs:
UBI: Fix two typos in comments
ubi: fastmap: fix spelling mistake: "invalidiate" -> "invalidate"
ubi: pr_err() strings should end with newlines
ubi: pr_err() strings should end with newlines
ubi: pr_err() strings should end with newlines
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.14 for MIPS; below a summary of
the non-merge commits:
CM:
- Rename mips_cm_base to mips_gcr_base
- Specify register size when generating accessors
- Use BIT/GENMASK for register fields, order & drop shifts
- Add cluster & block args to mips_cm_lock_other()
CPC:
- Use common CPS accessor generation macros
- Use BIT/GENMASK for register fields, order & drop shifts
- Introduce register modify (set/clear/change) accessors
- Use change_*, set_* & clear_* where appropriate
- Add CM/CPC 3.5 register definitions
- Use GlobalNumber macros rather than magic numbers
- Have asm/mips-cps.h include CM & CPC headers
- Cluster support for topology functions
- Detect CPUs in secondary clusters
CPS:
- Read GIC_VL_IDENT directly, not via irqchip driver
DMA:
- Consolidate coherent and non-coherent dma_alloc code
- Don't use dma_cache_sync to implement fd_cacheflush
FPU emulation / FP assist code:
- Another series of 14 commits fixing corner cases such as NaN
propgagation and other special input values.
- Zero bits 32-63 of the result for a CLASS.D instruction.
- Enhanced statics via debugfs
- Do not use bools for arithmetic. GCC 7.1 moans about this.
- Correct user fault_addr type
Generic MIPS:
- Enhancement of stack backtraces
- Cleanup from non-existing options
- Handle non word sized instructions when examining frame
- Fix detection and decoding of ADDIUSP instruction
- Fix decoding of SWSP16 instruction
- Refactor handling of stack pointer in get_frame_info
- Remove unreachable code from force_fcr31_sig()
- Convert to using %pOF instead of full_name
- Remove the R6000 support.
- Move FP code from *_switch.S to *_fpu.S
- Remove unused ST_OFF from r2300_switch.S
- Allow platform to specify multiple its.S files
- Add #includes to various files to ensure code builds reliable and
without warning..
- Remove __invalidate_kernel_vmap_range
- Remove plat_timer_setup
- Declare various variables & functions static
- Abstract CPU core & VP(E) ID access through accessor functions
- Store core & VP IDs in GlobalNumber-style variable
- Unify checks for sibling CPUs
- Add CPU cluster number accessors
- Prevent direct use of generic_defconfig
- Make CONFIG_MIPS_MT_SMP default y
- Add __ioread64_copy
- Remove unnecessary inclusions of linux/irqchip/mips-gic.h
GIC:
- Introduce asm/mips-gic.h with accessor functions
- Use new GIC accessor functions in mips-gic-timer
- Remove counter access functions from irq-mips-gic.c
- Remove gic_read_local_vp_id() from irq-mips-gic.c
- Simplify shared interrupt pending/mask reads in irq-mips-gic.c
- Simplify gic_local_irq_domain_map() in irq-mips-gic.c
- Drop gic_(re)set_mask() functions in irq-mips-gic.c
- Remove gic_set_polarity(), gic_set_trigger(), gic_set_dual_edge(),
gic_map_to_pin() and gic_map_to_vpe() from irq-mips-gic.c.
- Convert remaining shared reg access, local int mask access and
remaining local reg access to new accessors
- Move GIC_LOCAL_INT_* to asm/mips-gic.h
- Remove GIC_CPU_INT* macros from irq-mips-gic.c
- Move various definitions to the driver
- Remove gic_get_usm_range()
- Remove __gic_irq_dispatch() forward declaration
- Remove gic_init()
- Use mips_gic_present() in place of gic_present and remove
gic_present
- Move gic_get_c0_*_int() to asm/mips-gic.h
- Remove linux/irqchip/mips-gic.h
- Inline __gic_init()
- Inline gic_basic_init()
- Make pcpu_masks a per-cpu variable
- Use pcpu_masks to avoid reading GIC_SH_MASK*
- Clean up mti, reserved-cpu-vectors handling
- Use cpumask_first_and() in gic_set_affinity()
- Let the core set struct irq_common_data affinity
microMIPS:
- Fix microMIPS stack unwinding on big endian systems
MIPS-GIC:
- SYNC after enabling GIC region
NUMA:
- Remove the unused parent_node() macro
R6:
- Constify r2_decoder_tables
- Add accessor & bit definitions for GlobalNumber
SMP:
- Constify smp ops
- Allow boot_secondary SMP op to return errors
VDSO:
- Drop gic_get_usm_range() usage
- Avoid use of linux/irqchip/mips-gic.h
Platform changes:
Alchemy:
- Add devboard machine type to cpuinfo
- update cpu feature overrides
- Threaded carddetect irqs for devboards
AR7:
- allow NULL clock for clk_get_rate
BCM63xx:
- Fix ENETDMA_6345_MAXBURST_REG offset
- Allow NULL clock for clk_get_rate
CI20:
- Enable GPIO and RTC drivers in defconfig
- Add ethernet and fixed-regulator nodes to DTS
Generic platform:
- Move Boston and NI 169445 FIT image source to their own files
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Allow filtering enabled boards by requirements
- Don't explicitly disable CONFIG_USB_SUPPORT
- Bump default NR_CPUS to 16
JZ4700:
- Probe the jz4740-rtc driver from devicetree
Lantiq:
- Drop check of boot select from the spi-falcon driver.
- Drop check of boot select from the lantiq-flash MTD driver.
- Access boot cause register in the watchdog driver through regmap
- Add device tree binding documentation for the watchdog driver
- Add docs for the RCU DT bindings.
- Convert the fpi bus driver to a platform_driver
- Remove ltq_reset_cause() and ltq_boot_select(
- Switch to a proper reset driver
- Switch to a new drivers/soc GPHY driver
- Add an USB PHY driver for the Lantiq SoCs using the RCU module
- Use of_platform_default_populate instead of __dt_register_buses
- Enable MFD_SYSCON to be able to use it for the RCU MFD
- Replace ltq_boot_select() with dummy implementation.
Loongson 2F:
- Allow NULL clock for clk_get_rate
Malta:
- Use new GIC accessor functions
NI 169445:
- Add support for NI 169445 board.
- Only include in 32r2el kernels
Octeon:
- Add support for watchdog of 78XX SOCs.
- Add support for watchdog of CN68XX SOCs.
- Expose support for mips32r1, mips32r2 and mips64r1
- Enable more drivers in config file
- Add support for accessing the boot vector.
- Remove old boot vector code from watchdog driver
- Define watchdog registers for 70xx, 73xx, 78xx, F75xx.
- Make CSR functions node aware.
- Allow access to CIU3 IRQ domains.
- Misc cleanups in the watchdog driver
Omega2+:
- New board, add support and defconfig
Pistachio:
- Enable Root FS on NFS in defconfig
Ralink:
- Add Mediatek MT7628A SoC
- Allow NULL clock for clk_get_rate
- Explicitly request exclusive reset control in the pci-mt7620 PCI driver.
SEAD3:
- Only include in 32 bit kernels by default
VoCore:
- Add VoCore as a vendor t0 dt-bindings
- Add defconfig file"
* '4.14-features' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (167 commits)
MIPS: Refactor handling of stack pointer in get_frame_info
MIPS: Stacktrace: Fix microMIPS stack unwinding on big endian systems
MIPS: microMIPS: Fix decoding of swsp16 instruction
MIPS: microMIPS: Fix decoding of addiusp instruction
MIPS: microMIPS: Fix detection of addiusp instruction
MIPS: Handle non word sized instructions when examining frame
MIPS: ralink: allow NULL clock for clk_get_rate
MIPS: Loongson 2F: allow NULL clock for clk_get_rate
MIPS: BCM63XX: allow NULL clock for clk_get_rate
MIPS: AR7: allow NULL clock for clk_get_rate
MIPS: BCM63XX: fix ENETDMA_6345_MAXBURST_REG offset
mips: Save all registers when saving the frame
MIPS: Add DWARF unwinding to assembly
MIPS: Make SAVE_SOME more standard
MIPS: Fix issues in backtraces
MIPS: jz4780: DTS: Probe the jz4740-rtc driver from devicetree
MIPS: Ci20: Enable RTC driver
watchdog: octeon-wdt: Add support for 78XX SOCs.
watchdog: octeon-wdt: Add support for cn68XX SOCs.
watchdog: octeon-wdt: File cleaning.
...
Pull more set_fs removal from Al Viro:
"Christoph's 'use kernel_read and friends rather than open-coding
set_fs()' series"
* 'work.set_fs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: unexport vfs_readv and vfs_writev
fs: unexport vfs_read and vfs_write
fs: unexport __vfs_read/__vfs_write
lustre: switch to kernel_write
gadget/f_mass_storage: stop messing with the address limit
mconsole: switch to kernel_read
btrfs: switch write_buf to kernel_write
net/9p: switch p9_fd_read to kernel_write
mm/nommu: switch do_mmap_private to kernel_read
serial2002: switch serial2002_tty_write to kernel_{read/write}
fs: make the buf argument to __kernel_write a void pointer
fs: fix kernel_write prototype
fs: fix kernel_read prototype
fs: move kernel_read to fs/read_write.c
fs: move kernel_write to fs/read_write.c
autofs4: switch autofs4_write to __kernel_write
ashmem: switch to ->read_iter
Trivial fix to spelling mistake in ubi_err error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
In build.c, the following pr_err calls should be terminated with
a new-line to avoid other messages being concatenated onto the end.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
In ubi_attach_mtd_dev() the pr_err() calls should have their
messgaes terminated with a new-line to avoid other messages
being concatenated onto the end.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
The ubi_init() function has a few error paths that use the
pr_err() to output errors. These should have new lines on
them as pr_err() does not automatically do this.
This fixes issues where if multiple mtd fail to bind to
ubi the console output starts wrapping around.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
General updates:
* Constify pci_device_id in various drivers
* Constify device_type
* Remove pad control code from the Gemini driver
* Use %pOF to print OF node full_name
* Various fixes in the physmap_of driver
* Remove unused vars in mtdswap
* Check devm_kzalloc() return value in the spear_smi driver
* Check clk_prepare_enable() return code in the st_spi_fsm driver
* Create per MTD device debugfs enties
NAND updates, from Boris Brezillon:
* Fix memory leaks in the core
* Remove unused NAND locking support
* Rename nand.h into rawnand.h (preparing support for spi NANDs)
* Use NAND_MAX_ID_LEN where appropriate
* Fix support for 20nm Hynix chips
* Fix support for Samsung and Hynix SLC NANDs
* Various cleanup, improvements and fixes in the qcom driver
* Fixes for bugs detected by various static code analysis tools
* Fix mxc ooblayout definition
* Add a new part_parsers to tmio and sharpsl platform data in order to
define a custom list of partition parsers
* Request the reset line in exclusive mode in the sunxi driver
* Fix a build error in the orion-nand driver when compiled for ARMv4
* Allow 64-bit mvebu platforms to select the PXA3XX driver
SPI NOR updates, from Cyrille Pitchen and Marek Vasut:
* add support to the JEDEC JESD216B specification (SFDP tables).
* add support to the Intel Denverton SPI flash controller.
* fix error recovery for Spansion/Cypress SPI NOR memories.
* fix 4-byte address management for the Aspeed SPI controller.
* add support to some Microchip SST26 memory parts
* remove unneeded pinctrl header Write a message for tag:
-----BEGIN PGP SIGNATURE-----
iQJABAABCAAqBQJZrav6Ixxib3Jpcy5icmV6aWxsb25AZnJlZS1lbGVjdHJvbnMu
Y29tAAoJEGXtNgF+CLcABwkP/joDrq09RIC9n5gP+ubJe6O1jKvNWDd6bIVXD3Ke
73R0a0ANwwWlNYWTChTdrb8UeewVS1bzutyy5O2Sbdb6Jc6s7xkfQDTsbET2HWOK
S7Lt/zjlC6/6cow59B6h43PGS6wmIFaZD3K+70sGhvFnV8epVUzS2Aa783xS8LXm
so2djZOdUYnW+yE0eho24VQR6nS4YP4Vc+7Mm9skjU0ifjB9mJiWRkzoQnqIgORO
M+Iab+qjDs9KR/edWh6mZtnvjps0VSW4I40YsClpcgIn550w1DSXe4u6/8Nk+2Bp
gfrALls91gob0ocxmEdIyLID+M0410HcN/Lvh36nw+tkkGTaXf0D6mkqzdKNrZ3w
yz+UV9uf19kr1c6zFGcCvUlD0btn9KT+F2legnhgURtwUyDFQcaYQlkpDIeEzUMV
ZrtzKbSE2v9810YKXjtCnseewdP+Eph/ewN6ODX5yg/fs8K0fyQYTRtYYM50U69X
md8zznBBDPhJVu5T2Of7my9V1SxvCP8a7LrKjAXuFHpZ/CHiPe+QOWBgG2L+zXXT
e10/rTg7T2pcyKpBvL/3/mCYeJ+Iup3lKT1EHGCXcKnLGecVgOsbvdG+JnvQMI2J
FLmu1exvrzi0Gcrs/05hqwyUvkHZ5FB1a+heNOtmQ+h1U0ElXqILyu7brzghupRe
3phO
=UgCd
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20170904' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"General updates:
- Constify pci_device_id in various drivers
- Constify device_type
- Remove pad control code from the Gemini driver
- Use %pOF to print OF node full_name
- Various fixes in the physmap_of driver
- Remove unused vars in mtdswap
- Check devm_kzalloc() return value in the spear_smi driver
- Check clk_prepare_enable() return code in the st_spi_fsm driver
- Create per MTD device debugfs enties
NAND updates, from Boris Brezillon:
- Fix memory leaks in the core
- Remove unused NAND locking support
- Rename nand.h into rawnand.h (preparing support for spi NANDs)
- Use NAND_MAX_ID_LEN where appropriate
- Fix support for 20nm Hynix chips
- Fix support for Samsung and Hynix SLC NANDs
- Various cleanup, improvements and fixes in the qcom driver
- Fixes for bugs detected by various static code analysis tools
- Fix mxc ooblayout definition
- Add a new part_parsers to tmio and sharpsl platform data in order
to define a custom list of partition parsers
- Request the reset line in exclusive mode in the sunxi driver
- Fix a build error in the orion-nand driver when compiled for ARMv4
- Allow 64-bit mvebu platforms to select the PXA3XX driver
SPI NOR updates, from Cyrille Pitchen and Marek Vasut:
- add support to the JEDEC JESD216B specification (SFDP tables).
- add support to the Intel Denverton SPI flash controller.
- fix error recovery for Spansion/Cypress SPI NOR memories.
- fix 4-byte address management for the Aspeed SPI controller.
- add support to some Microchip SST26 memory parts
- remove unneeded pinctrl header Write a message for tag:"
* tag 'for-linus-20170904' of git://git.infradead.org/linux-mtd: (74 commits)
mtd: nand: complain loudly when chip->bits_per_cell is not correctly initialized
mtd: nand: make Samsung SLC NAND usable again
mtd: nand: tmio: Register partitions using the parsers
mfd: tmio: Add partition parsers platform data
mtd: nand: sharpsl: Register partitions using the parsers
mtd: nand: sharpsl: Add partition parsers platform data
mtd: nand: qcom: Support for IPQ8074 QPIC NAND controller
mtd: nand: qcom: support for IPQ4019 QPIC NAND controller
dt-bindings: qcom_nandc: IPQ8074 QPIC NAND documentation
dt-bindings: qcom_nandc: IPQ4019 QPIC NAND documentation
dt-bindings: qcom_nandc: fix the ipq806x device tree example
mtd: nand: qcom: support for different DEV_CMD register offsets
mtd: nand: qcom: QPIC data descriptors handling
mtd: nand: qcom: enable BAM or ADM mode
mtd: nand: qcom: erased codeword detection configuration
mtd: nand: qcom: support for read location registers
mtd: nand: qcom: support for passing flags in DMA helper functions
mtd: nand: qcom: add BAM DMA descriptor handling
mtd: nand: qcom: allocate BAM transaction
mtd: nand: qcom: DMA mapping support for register read buffer
...
This macro is useful to avoid link error on 32-bit systems.
We have the same definition in two drivers, so move it to
include/linux/kernel.h
While we are here, refactor DIV_ROUND_UP_ULL() by using
DIV_ROUND_DOWN_ULL().
Link: http://lkml.kernel.org/r/1500945156-12907-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For HSMC controller, the register layout depends on the device i.e. the
offset of setup, pulse, cycle, mode and timings registers is not the
same. An helper is added to provide the correct register layout.
Fixes: fe9d7cb22e ("mfd: syscon: atmel-smc: Add new helpers to ease
SMC regs manipulation")
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Make the position an in/out argument like all the other read/write
helpers and and make the buf argument a void pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Use proper ssize_t and size_t types for the return value and count
argument, move the offset last and make it an in/out argument like
all other read/write helpers, and make the buf argument a void pointer
to get rid of lots of casts in the callers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* Fix memory leaks in the core
* Remove unused NAND locking support
* Rename nand.h into rawnand.h (preparing support for spi NANDs)
* Use NAND_MAX_ID_LEN where appropriate
* Fix support for 20nm Hynix chips
* Fix support for Samsung and Hynix SLC NANDs
and the following driver changes:
* Various cleanup, improvements and fixes in the qcom driver
* Fixes for bugs detected by various static code analysis tools
* Fix mxc ooblayout definition
* Add a new part_parsers to tmio and sharpsl platform data in order to
define a custom list of partition parsers
* Request the reset line in exclusive mode in the sunxi driver
* Fix a build error in the orion-nand driver when compiled for ARMv4
* Allow 64-bit mvebu platforms to select the PXA3XX driver
-----BEGIN PGP SIGNATURE-----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=bC1+
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.14' of git://git.infradead.org/l2-mtd into mtd/next
From Boris:
"
This pull request contains the following core changes:
* Fix memory leaks in the core
* Remove unused NAND locking support
* Rename nand.h into rawnand.h (preparing support for spi NANDs)
* Use NAND_MAX_ID_LEN where appropriate
* Fix support for 20nm Hynix chips
* Fix support for Samsung and Hynix SLC NANDs
and the following driver changes:
* Various cleanup, improvements and fixes in the qcom driver
* Fixes for bugs detected by various static code analysis tools
* Fix mxc ooblayout definition
* Add a new part_parsers to tmio and sharpsl platform data in order to
define a custom list of partition parsers
* Request the reset line in exclusive mode in the sunxi driver
* Fix a build error in the orion-nand driver when compiled for ARMv4
* Allow 64-bit mvebu platforms to select the PXA3XX driver
"
- add support to the JEDEC JESD216B specification (SFDP tables).
- add support to the Intel Denverton SPI flash controller.
- fix error recovery for Spansion/Cypress SPI NOR memories.
- fix 4-byte address management for the Aspeed SPI controller.
- add support to some Microchip SST26 memory parts
- remove unneeded pinctrl header
-----BEGIN PGP SIGNATURE-----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=A8bR
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-4.14' of git://git.infradead.org/l2-mtd into mtd/next
From Cyrille:
"
This pull request contains the following notable changes:
- add support to the JEDEC JESD216B specification (SFDP tables).
- add support to the Intel Denverton SPI flash controller.
- fix error recovery for Spansion/Cypress SPI NOR memories.
- fix 4-byte address management for the Aspeed SPI controller.
- add support to some Microchip SST26 memory parts
- remove unneeded pinctrl header
"
commit c51d0ac59f ("mtd: nand: Move Samsung specific init/detection
logic in nand_samsung.c") introduced a regression for Samsung SLC NAND
chips. Prior to this commit chip->bits_per_cell was initialized by calling
nand_get_bits_per_cell() before using nand_is_slc().
With the offending commit this call is skipped, leaving
chip->bits_per_cell cleared to zero when the manufacturer specific
'.detect' function calls nand_is_slc() which in turn interprets
bits_per_cell != 1 as indication for an MLC chip.
The effect is that e.g. a K9F1G08U0F NAND chip is falsely detected as
MLC NAND with 4KiB page size rather than SLC with 2KiB page size.
Add a call to nand_get_bits_per_cell() before calling the .detect hook
function in nand_manufacturer_detect(), so that the nand_is_slc()
calls in the manufacturer specific code will return correct results.
Fixes: c51d0ac59f ("mtd: nand: Move Samsung specific init/detection logic in nand_samsung.c")
Cc: <stable@vger.kernel.org>
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZo2HiAAoJEHm+PkMAQRiG3OcIAJqSeVK2uQ/QhmqFN1ExYay4
bdTjSTtSk7GH6PxI2C0cqfZvsxOUU7ICDHG8bYM1LA0S0SxfOtoFhHGKc/BcFLX8
MiKJWlF51ZbX0mkIEpKF+C8pRrXPgSqtk3N450/k2BzG9qCZSM93A2NCOB7v9T9w
XOBUIYHqfTS2tdmCinjwu8Ls+w8oPOGH1gLjxZyGnBlg4lTqHMcUufmHeVEAh11d
giGByqqqXH69kGD1HNC7H6quzXN9rz4n0gEwEG0mIhfkJ98b+ESSWwSEXXypOAQD
QT5/6+2YizXf5DPCqR46xasQCPjRsS6Sv0cF2cntW2PEAb4jBjhx5gTFlJcoOC8=
=efWJ
-----END PGP SIGNATURE-----
Merge tag 'v4.13-rc7' into mtd/next
Merge v4.13-rc7 back to resolve merge conflicts in
drivers/mtd/nand/nandsim.c and include/asm-generic/vmlinux.lds.h.
Version 4 of the ONFI spec mandates that tADL be at least 400 nanoseconds,
but, depending on the master clock rate, 400 ns may not fit in the tADL
field of the SMC reg. We need to relax the check and accept the -ERANGE
return code.
Note that previous versions of the ONFI spec had a lower tADL_min (100 or
200 ns). It's not clear why this timing constraint got increased but it
seems most NANDs are fine with values lower than 400ns, so we should be
safe.
Fixes: f9ce2eddf1 ("mtd: nand: atmel: Add ->setup_data_interface() hooks")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The debugfs entries must be removed before an error is returned in the
probe function. Otherwise another try to load the module fails and when
the debugfs files are accessed without the module loaded, the kernel
still tries to call a function in that module.
Fixes: 5346c27c5f ("mtd: nandsim: Introduce debugfs infrastructure")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
With the introduction of sharpslpart partition parser we can now read the
offsets from NAND: we specify the list of the parsers as platform data, with
cmdlinepart and ofpart parsers first allowing to override the part. table
written in NAND. This is done in the board files using this driver.
Use now these parsers.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
With the introduction of sharpslpart partition parser we can now read the
offsets from NAND: we specify the list of the parsers as platform data, with
cmdlinepart and ofpart parsers first allowing to override the part. table
written in NAND. This is done in the board files using this driver.
Use now these parsers.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Add the compatible string for IPQ8074 QPIC NAND controller
version 1.5.0 which uses BAM DMA and its FLASH_DEV_CMD registers
starting offset is 0x7000.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The FLASH_DEV_CMD registers starting offset is not same in
different QPIC NAND controller versions. This patch adds
the starting offset in NAND controller properties and uses
the same for calculating the actual offset of these registers.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
1. Add the data descriptor preparation function which will be used
only by BAM DMA for forming the data SGL’s
2. Add clear BAM transaction and call it before every new request
3. Check DMA mode for ADM or BAM and call the appropriate
descriptor formation function.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
1. DM_EN is only required for EBI2 NAND controller which uses ADM
2. BAM mode will be disabled after power on reset which needs to
be enabled before starting any BAM transfers.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The NAND controller returns ECC failure during read of completely
erased codeword. The NAND controller has hardware functionality
to detect erased codeword in case of BCH ECC algorithm. The
NAND_ERASED_CW_DETECT_CFG register controls the erased
codeword/page detection controller. This register should be reset
before every page read by setting and clearing bit 0 of
NAND_ERASED_CW_DETECT_CFG.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
In EBI2, all codeword data will be read in FLASH_BUF_ACC buffer
and ADM will copy the data from source (FLASH_BUF_ACC) to
destination (memory for data read).
In QPIC, there is no FLASH_BUF_ACC and all the codeword data will
held in QPIC BAM FIFO buffers. It provides multiple READ_LOCATION
registers which will be used for copying the data from FIFO to
memory. The READ_LOCATION register will be used to read a
specific amount of data from a specific offset within the flash
buffer. It supports sequential offset requests. Each request is
composed of the following fields:
a. Offset within the flash buffer from which data should be
read
b. Amount of data to be read
c. Flag bit specifying the last read request from the flash
buffer. Following the last read request the NANDc refers to the
buffer as empty.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The QPIC NAND BAM has multiple flags to control the transfer. This
patch adds flags parameter in register and data transfer DMA helper
functions and modifies all these functions call with appropriate
flags using following rule
1. Read and write can’t go in single command descriptor so
separate SGL should be used.
2. For some of the requests, NWD flag should be set in BAM
DMA descriptor.
3. For Data write, the BAM has internal buffer for each codeword.
All write request will modify the data in internal buffer and
this buffer will be flushed to NAND device once EOT flag is set.
So for all the write requests in single codeword, the EOT should
be cleared for all tx data descriptors except the last one.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
1. prepare_bam_async_desc is the function which will call
all the DMA API’s. It will fetch the outstanding scatter gather
list for passed channel and will do the DMA descriptor formation.
The DMA flag is dependent upon the type of channel.
2. For ADM DMA, the descriptor is being formed for every DMA
request so its sgl count will be always 1 while in BAM DMA, the
clubbing of descriptor is being done to increase throughput.
3. ADM DMA uses only one channel while in BAM DMA, data descriptors
will be submitted to tx channel (for write) or rx channel
(for read) and all the registers read/write descriptors in
command channel.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
- The BAM transaction is the core data structure which will be used
for all the data transfers in QPIC NAND. Since the core framework
in nand_base.c is serializing all the NAND requests so allocating
BAM transaction before every transfer will be overhead. The memory
for it be allocated during probe time and before every transfer,
it will be cleared.
- The BAM transaction contains the array of
command and data scatter gather list and indexes. For
every transfer, all the resource will be taken from BAM
transaction.
- The size of the buffer used for BAM transactions
is calculated based on the NAND device with the maximum page size,
among all the devices connected to the
controller.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The EBI2 NAND controller directly remaps register read buffer with
dma_map_sg and DMA address of this buffer will be passed to DMA
API’s. While, on QPIC NAND controller, which uses BAM DMA, we read
the controller registers by preparing a BAM command descriptor. This
command descriptor requires the
- controller register address
- the DMA address in which we want to store the value read
back from the controller register.
This command descriptor will be remapped with dma_map_sg
and its DMA address will be passed to DMA API’s. Therefore,
it's required that we also map our register read buffer for
DMA (using dma_map_single). We use the returned DMA address
for preparing entries in our command descriptor.
This patch adds the DMA mapping support for register read
buffer. This buffer will be DMA mapped during allocation
time. Before starting of any operation, this buffer will
be synced for device operation and after operation
completion, it will be synced again for CPU.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
1. QPIC NAND controller uses 3 BAM channels: command, data tx
and data rx while EBI2 NAND controller uses only single ADM
channel.
2. CRCI is only required for ADM DMA and it's not required for
BAM DMA.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The current driver only supports EBI2 NAND controller which uses
ADM DMA. The latest QCOM SoC uses QPIC NAND controller with BAM
DMA. NAND registers and programming sequence are same for EBI2
and QPIC NAND so the same driver can support QPIC NAND also by
adding the BAM DMA support. This patch adds the is_bam in NAND
property which will be checked for determining the DMA engine type.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Currently driver data is being assigned directly with ECC modes.
Now, the plan is to add more NAND controller versions which will
have different properties. This patch reorganizes the current driver
data assignment by creating NAND controller properties structure
which will contain all properties specific to NAND controller.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The NAND page read fails without complete boot chain since
NAND_DEV_CMD_VLD value is not proper. The default power on reset
value for this register is
0xe - ERASE_START_VALID | WRITE_START_VALID | READ_STOP_VALID
The READ_START_VALID should be enabled for sending PAGE_READ
command. READ_STOP_VALID should be cleared since normal NAND
page read does not require READ_STOP command.
Fixes: c76b78d8ec ("mtd: nand: Qualcomm NAND controller driver")
Cc: stable@vger.kernel.org
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
platform_get_irq() returns an error code, but the mtk_ecc driver
ignores it and always returns -EINVAL. This is not correct and,
prevents -EPROBE_DEFER from being propagated properly.
Print and propagate the return value of platform_get_irq on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
platform_get_irq() returns an error code, but the sh_flctl
driver ignores it and always returns -ENXIO. This is not correct
and, prevents -EPROBE_DEFER from being propagated properly.
Print and propagate the return value of platform_get_irq on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The return value of dma_map_single() should be checked by
dma_mapping_error(). However, in function flctl_dma_fifo0_transfer(), its
return value is checked against NULL, which could result in failures.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
of_irq_get() may return 0 as well as negative error number on failure,
while the driver only checks for the negative values. The driver would
then call devm_request_irq() for IRQ0 in its probe method and never get
a valid interrupt.
Check for 'nc->irq <= 0' instead and return -ENXIO from the driver's probe
if of_irq_get() returned 0.
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Wenyou Yang <Wenyou.yang@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
According to the datasheet of the H27UCG8T2BTR the NAND Technology field
(6th byte of the "Device Identifier Description", bits 0-2) the
following values are possible:
- 0x0 = 48nm
- 0x1 = 41nm
- 0x2 = 32nm
- 0x3 = 26nm
- 0x4 = 20nm
- (all others are reserved)
Fix this by extending the mask for this field to allow detecting value
0x4 (20nm) as valid NAND technology.
Without this the detection of the ECC requirements fails, because the
code assumes that the device is a 48nm device (0x4 & 0x3 = 0x0) and
aborts with "Invalid ECC requirements" because it cannot map the "ECC
Level". Extending the mask makes the ECC requirement detection code
recognize this chip as <= 26nm and sets up the ECC step size and ECC
strength correctly.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Fixes: 78f3482d74 ("mtd: nand: hynix: Rework NAND ID decoding to extract more information")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Commit a894cf6c5a ("mtd: nand: mxc: switch to mtd_ooblayout_ops")
introduced a bug in the OOB layout description. Even if the driver claims
that 3 ECC bytes are reserved to protect 512 bytes of data, it's actually
5 ECC bytes to protect 512+6 bytes of data (some OOB bytes are also
protected using extra ECC bytes).
Fix the mxc_v1_ooblayout_{free,ecc}() functions to reflect this behavior.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: a894cf6c5a ("mtd: nand: mxc: switch to mtd_ooblayout_ops")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
- clk_prepare_enable() can fail here and we must check its return value.
- stfsm_probe() can fail here and we must disable clock.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
- clk_prepare_enable() can fail here and we must check its return value.
- oxnas_nand_probe() can fail here and we must disable clock.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Boris Brezillon