My recent Intel box is spewing these messages:
xhci_hcd 0000:00:14.0: xHCI Host Controller
xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: xHCI Host Controller
usb usb2: Manufacturer: Linux 4.3.0+ xhci-hcd
usb usb2: SerialNumber: 0000:00:14.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
usb: failed to peer usb2-port2 and usb1-port1 by location (usb2-port2:none) (usb1-port1:usb2-port1)
usb usb2-port2: failed to peer to usb1-port1 (-16)
usb: port power management may be unreliable
usb: failed to peer usb2-port3 and usb1-port1 by location (usb2-port3:none) (usb1-port1:usb2-port1)
usb usb2-port3: failed to peer to usb1-port1 (-16)
usb: failed to peer usb2-port5 and usb1-port1 by location (usb2-port5:none) (usb1-port1:usb2-port1)
usb usb2-port5: failed to peer to usb1-port1 (-16)
usb: failed to peer usb2-port6 and usb1-port1 by location (usb2-port6:none) (usb1-port1:usb2-port1)
usb usb2-port6: failed to peer to usb1-port1 (-16)
Diving into the acpi tables, I noticed the EHCI hub has 12 ports while the XHCI
hub has 8 ports. Most of those ports are of connect type USB_PORT_NOT_USED
(including port 1 of the EHCI hub).
Further the unused ports have location data initialized to 0x80000000.
Now each unused port on the xhci hub walks the port list and finds a matching
peer with port1 of the EHCI hub because the zero'd out group id bits falsely match.
After port1 of the XHCI hub, each following matching peer will generate the
above warning.
These warnings seem to be harmless for this scenario as I don't think it
matters that unused ports could not create a peer link.
The attached patch utilizes that assumption and just turns the pr_warn into
pr_debug to quiet things down.
Tested on my Intel box.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if a full speed hub connects to a high speed hub which
supports MTT, the MTT field of its slot context will be set
to 1 when xHCI driver setups an xHCI virtual device in
xhci_setup_addressable_virt_dev(); once usb core fetch its
hub descriptor, and need to update the xHC's internal data
structures for the device, the HUB field of its slot context
will be set to 1 too, meanwhile MTT is also set before,
this will cause configure endpoint command fail, so in the
case, we should clear MTT to 0 for full speed hub according
to section 6.2.2
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a memory leak because acpi_evaluate_dsm() actually returns an
object which the caller is supposed to release. Fix this by calling
ACPI_FREE() for the returned object (this expands to kfree() so passing
NULL there is fine as well).
While there correct indentation in !CONFIG_ACPI case.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable <stable@vger.kernel.org> # v4.2
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert commit 033291eccb ("vfio: Include No-IOMMU mode") due to lack
of a user. This was originally intended to fill a need for the DPDK
driver, but uptake has been slow so rather than support an unproven
kernel interface revert it and revisit when userspace catches up.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Commit 4e752f0ab0 ("rbd: access snapshot context and mapping size
safely") moved ceph_get_snap_context() out of rbd_img_request_create()
and into rbd_queue_workfn(), adding a ceph_put_snap_context() to the
error path in rbd_queue_workfn(). However, rbd_img_request_create()
consumes a ref on snapc, so calling ceph_put_snap_context() after
a successful rbd_img_request_create() leads to an extra put. Fix it.
Cc: stable@vger.kernel.org # 3.18+
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Josh Durgin <jdurgin@redhat.com>
* pm-domains:
PM / Domains: Fix bad of_node_put() in failure paths of genpd_dev_pm_attach()
PM / Domains: Validate cases of a non-bound driver in genpd governor
* pm-cpufreq:
cpufreq: use last policy after online for drivers with ->setpolicy
Oleg noticed that its possible to falsely observe p->on_cpu == 0 such
that we'll prematurely continue with the wakeup and effectively run p on
two CPUs at the same time.
Even though the overlap is very limited; the task is in the middle of
being scheduled out; it could still result in corruption of the
scheduler data structures.
CPU0 CPU1
set_current_state(...)
<preempt_schedule>
context_switch(X, Y)
prepare_lock_switch(Y)
Y->on_cpu = 1;
finish_lock_switch(X)
store_release(X->on_cpu, 0);
try_to_wake_up(X)
LOCK(p->pi_lock);
t = X->on_cpu; // 0
context_switch(Y, X)
prepare_lock_switch(X)
X->on_cpu = 1;
finish_lock_switch(Y)
store_release(Y->on_cpu, 0);
</preempt_schedule>
schedule();
deactivate_task(X);
X->on_rq = 0;
if (X->on_rq) // false
if (t) while (X->on_cpu)
cpu_relax();
context_switch(X, ..)
finish_lock_switch(X)
store_release(X->on_cpu, 0);
Avoid the load of X->on_cpu being hoisted over the X->on_rq load.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Explain how the control dependency and smp_rmb() end up providing
ACQUIRE semantics and pair with smp_store_release() in
finish_lock_switch().
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
/proc/stats shows invalid gtime when the thread is running in guest.
When vtime accounting is not enabled, we cannot get a valid delta.
The delta is calculated with now - tsk->vtime_snap, but tsk->vtime_snap
is only updated when vtime accounting is runtime enabled.
This patch makes task_gtime() just return gtime without computing the
buggy non-existing tickless delta when vtime accounting is not enabled.
Use context_tracking_is_enabled() to check if vtime is accounting on
some cpu, in which case only we need to check the tickless delta. This
way we fix the gtime value regression on machines not running nohz full.
The kernel config contains CONFIG_VIRT_CPU_ACCOUNTING_GEN=y and
CONFIG_NO_HZ_FULL_ALL=n and boot without nohz_full.
I ran and stop a busy loop in VM and see the gtime in host.
Dump the 43rd field which shows the gtime in every second:
# while :; do awk '{print $3" "$43}' /proc/3955/task/4014/stat; sleep 1; done
S 4348
R 7064566
R 7064766
R 7064967
R 7065168
S 4759
S 4759
During running busy loop, it returns large value.
After applying this patch, we can see right gtime.
# while :; do awk '{print $3" "$43}' /proc/10913/task/10956/stat; sleep 1; done
S 5338
R 5365
R 5465
R 5566
R 5666
S 5726
S 5726
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul E . McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1447948054-28668-2-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
root_domain::rto_mask allocated through alloc_cpumask_var()
contains garbage data, this may cause problems. For instance,
When doing pull_rt_task(), it may do useless iterations if
rto_mask retains some extra garbage bits. Worse still, this
violates the isolated domain rule for clustered scheduling
using cpuset, because the tasks(with all the cpus allowed)
belongs to one root domain can be pulled away into another
root domain.
The patch cleans the garbage by using zalloc_cpumask_var()
instead of alloc_cpumask_var() for root_domain::rto_mask
allocation, thereby addressing the issues.
Do the same thing for root_domain's other cpumask memembers:
dlo_mask, span, and online.
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1449057179-29321-1-git-send-email-xlpang@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Because wakeups can (fundamentally) be late, a task might not be in
the expected state. Therefore testing against a task's state is racy,
and can yield false positives.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: oleg@redhat.com
Fixes: 9067ac85d5 ("wake_up_process() should be never used to wakeup a TASK_STOPPED/TRACED task")
Link: http://lkml.kernel.org/r/1448933660-23082-1-git-send-email-sasha.levin@oracle.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Vladimir reported getting RCU stall warnings and bisected it back to
commit:
743162013d ("sched: Remove proliferation of wait_on_bit() action functions")
That commit inadvertently reversed the calls to schedule() and signal_pending(),
thereby not handling the case where the signal receives while we sleep.
Reported-by: Vladimir Murzin <vladimir.murzin@arm.com>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: mark.rutland@arm.com
Cc: neilb@suse.de
Cc: oleg@redhat.com
Fixes: 743162013d ("sched: Remove proliferation of wait_on_bit() action functions")
Fixes: cbbce82209 ("SCHED: add some "wait..on_bit...timeout()" interfaces.")
Link: http://lkml.kernel.org/r/20151201130404.GL3816@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Recent PAT patchset has caused issue on 32-bit PAE machines:
page:eea45000 count:0 mapcount:-128 mapping: (null) index:0x0 flags: 0x40000000()
page dumped because: VM_BUG_ON_PAGE(page_mapcount(page) < 0)
------------[ cut here ]------------
kernel BUG at /home/build/linux-boris/mm/huge_memory.c:1485!
invalid opcode: 0000 [#1] SMP
[...]
Call Trace:
unmap_single_vma
? __wake_up
unmap_vmas
unmap_region
do_munmap
vm_munmap
SyS_munmap
do_fast_syscall_32
? __do_page_fault
sysenter_past_esp
Code: ...
EIP: [<c11bde80>] zap_huge_pmd+0x240/0x260 SS:ESP 0068:f6459d98
The problem is in pmd_pfn_mask() and pmd_flags_mask(). These
helpers use PMD_PAGE_MASK to calculate resulting mask.
PMD_PAGE_MASK is 'unsigned long', not 'unsigned long long' as
phys_addr_t is on 32-bit PAE (ARCH_PHYS_ADDR_T_64BIT). As a
result, the upper bits of resulting mask get truncated.
pud_pfn_mask() and pud_flags_mask() aren't problematic since we
don't have PUD page table level on 32-bit systems, but it's
reasonable to keep them consistent with PMD counterpart.
Introduce PHYSICAL_PMD_PAGE_MASK and PHYSICAL_PUD_PAGE_MASK in
addition to existing PHYSICAL_PAGE_MASK and reworks helpers to
use them.
Reported-and-Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
[ Fix -Woverflow warnings from the realmode code. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jürgen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: elliott@hpe.com
Cc: konrad.wilk@oracle.com
Cc: linux-mm <linux-mm@kvack.org>
Fixes: f70abb0fc3 ("x86/asm: Fix pud/pmd interfaces to handle large PAT bit")
Link: http://lkml.kernel.org/r/1448878233-11390-2-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Apparently pre-nv50 pageflip events happen before the actual vblank
period. Therefore that functionality got semi-disabled in
commit af4870e406
Author: Mario Kleiner <mario.kleiner.de@gmail.com>
Date: Tue May 13 00:42:08 2014 +0200
drm/nouveau/kms/nv04-nv40: fix pageflip events via special case.
Unfortunately that hack got uprooted in
commit cc1ef118fc
Author: Thierry Reding <treding@nvidia.com>
Date: Wed Aug 12 17:00:31 2015 +0200
drm/irq: Make pipe unsigned and name consistent
Triggering a warning when trying to sample the vblank timestamp for a
non-existing pipe. There's a few ways to fix this:
- Open-code the old behaviour, which just enshrines this slight
breakage of the userspace ABI.
- Revert Mario's commit and again inflict broken timestamps, again not
pretty.
- Fix this for real by delaying the pageflip TS until the next vblank
interrupt, thereby making it accurate.
This patch implements the third option. Since having a page flip
interrupt that happens when the pageflip gets armed and not when it
completes in the next vblank seems to be fairly common (older i915 hw
works very similarly) create a new helper to arm vblank events for
such drivers.
v2 (Mario Kleiner):
- Fix function prototypes in drmP.h
- Add missing vblank_put() for pageflip completion without
pageflip event.
- Initialize sequence number for queued pageflip event to avoid
trouble in drm_handle_vblank_events().
- Remove dead code and spelling fix.
v3 (Mario Kleiner):
- Add a signed-off-by and cc stable tag per Ilja's advice.
v4 (Thierry Reding):
- Fix kerneldoc typo, discovered by Michel Dänzer
- Rearrange tags and changelog
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=106431
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: stable@vger.kernel.org # v4.3
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The routines in scsi_pm.c assume that if a runtime-PM callback is
invoked for a SCSI device, it can only mean that the device's driver
has asked the block layer to handle the runtime power management (by
calling blk_pm_runtime_init(), which among other things sets q->dev).
However, this assumption turns out to be wrong for things like the ses
driver. Normally ses devices are not allowed to do runtime PM, but
userspace can override this setting. If this happens, the kernel gets
a NULL pointer dereference when blk_post_runtime_resume() tries to use
the uninitialized q->dev pointer.
This patch fixes the problem by checking q->dev in block layer before
handle runtime PM. Since ses doesn't define any PM callbacks and call
blk_pm_runtime_init(), the crash won't occur.
This fixes Bugzilla #101371.
https://bugzilla.kernel.org/show_bug.cgi?id=101371
More discussion can be found from below link.
http://marc.info/?l=linux-scsi&m=144163730531875&w=2
Signed-off-by: Ken Xue <Ken.Xue@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Xiangliang Yu <Xiangliang.Yu@amd.com>
Cc: James E.J. Bottomley <JBottomley@odin.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Michael Terry <Michael.terry@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
A client calling drmSetMaster() using a file descriptor that was opened
when another client was master would inherit the latter client's master
object and all its authenticated clients.
This is unwanted behaviour, and when this happens, instead allocate a
brand new master object for the client calling drmSetMaster().
Fixes a BUG() throw in vmw_master_set().
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Use drm_crtc_send_vblank_event to fix per crtc vblank handling
- Move the crtc device of_node assignment out of the ipuv3-crtc driver into
ipu-common code, where the devices are created.
- Fix parallel display support with simple-panels
- Remove some unused fields and superfluous checks
- Switch to universal planes and add error handling for primary plane creation
- Fix module autoload for TV encoder driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iEJU
-----END PGP SIGNATURE-----
Merge tag 'imx-drm-fixes-2015-12-01' of git://git.pengutronix.de/git/pza/linux into drm-fixes
imx-drm crtc, plane, parallel panel, and TV encoder fixes
- Use drm_crtc_send_vblank_event to fix per crtc vblank handling
- Move the crtc device of_node assignment out of the ipuv3-crtc driver into
ipu-common code, where the devices are created.
- Fix parallel display support with simple-panels
- Remove some unused fields and superfluous checks
- Switch to universal planes and add error handling for primary plane creation
- Fix module autoload for TV encoder driver
* tag 'imx-drm-fixes-2015-12-01' of git://git.pengutronix.de/git/pza/linux:
drm: imx: imx-tve: Fix module autoload for OF platform driver
drm: imx: convert to drm_crtc_send_vblank_event()
GPU-DRM-IMX: Delete an unnecessary check before drm_fbdev_cma_restore_mode()
drm/imx: Remove of_node assignment from ipuv3-crtc driver probe
gpu: ipu-v3: Assign of_node of child platform devices to corresponding ports
gpu: ipu-v3: Remove reg_offset field
gpu: ipu-v3: drop unused dmfc field from client platform data
drm/imx: parallel-display: allow to determine bus format from the connected panel
drm/imx: ipuv3-crtc: Return error if ipu_plane_init() fails for primary plane
drm/imx: switch to universal planes
Another batch of drm/i915 fixes for v4.4, on top of the ones from
earlier this week. One timeout handling regression fix from Chris, and
backport of five patches from our -next to fix a power management
related HDMI hotplug regression.
* tag 'drm-intel-fixes-2015-12-03' of git://anongit.freedesktop.org/drm-intel:
drm/i915: take a power domain reference while checking the HDMI live status
drm/i915: add MISSING_CASE to a few port/aux power domain helpers
drm/i915/ddi: fix intel_display_port_aux_power_domain() after HDMI detect
drm/i915: Introduce a gmbus power domain
drm/i915: Clean up AUX power domain handling
drm/i915: Check the timeout passed to i915_wait_request
It looks like these meant to be unreffing the
of_parse_phandle_with_args() node, since the error paths above it
don't do of_node_put. That function returns a new ref in pd_args.np,
though, not a new ref on dev->of_node. Also, it would have leaked the
ref in the success case.
Fixes "ERROR: Bad of_node_put()" on bcm2835 in the -EPROBE_DEFER case.
Fixes: aa42240ab2 (PM / Domains: Add generic OF-based PM domain look-up)
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Cc: 3.18+ <stable@vger.kernel.org> # 3.18+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull networking fixes from David Miller:
"A lot of Thanksgiving turkey leftovers accumulated, here goes:
1) Fix bluetooth l2cap_chan object leak, from Johan Hedberg.
2) IDs for some new iwlwifi chips, from Oren Givon.
3) Fix rtlwifi lockups on boot, from Larry Finger.
4) Fix memory leak in fm10k, from Stephen Hemminger.
5) We have a route leak in the ipv6 tunnel infrastructure, fix from
Paolo Abeni.
6) Fix buffer pointer handling in arm64 bpf JIT,f rom Zi Shen Lim.
7) Wrong lockdep annotations in tcp md5 support, fix from Eric
Dumazet.
8) Work around some middle boxes which prevent proper handling of TCP
Fast Open, from Yuchung Cheng.
9) TCP repair can do huge kmalloc() requests, build paged SKBs
instead. From Eric Dumazet.
10) Fix msg_controllen overflow in scm_detach_fds, from Daniel
Borkmann.
11) Fix device leaks on ipmr table destruction in ipv4 and ipv6, from
Nikolay Aleksandrov.
12) Fix use after free in epoll with AF_UNIX sockets, from Rainer
Weikusat.
13) Fix double free in VRF code, from Nikolay Aleksandrov.
14) Fix skb leaks on socket receive queue in tipc, from Ying Xue.
15) Fix ifup/ifdown crach in xgene driver, from Iyappan Subramanian.
16) Fix clearing of persistent array maps in bpf, from Daniel
Borkmann.
17) In TCP, for the cross-SYN case, we don't initialize tp->copied_seq
early enough. From Eric Dumazet.
18) Fix out of bounds accesses in bpf array implementation when
updating elements, from Daniel Borkmann.
19) Fill gaps in RCU protection of np->opt in ipv6 stack, from Eric
Dumazet.
20) When dumping proxy neigh entries, we have to accomodate NULL
device pointers properly, from Konstantin Khlebnikov.
21) SCTP doesn't release all ipv6 socket resources properly, fix from
Eric Dumazet.
22) Prevent underflows of sch->q.qlen for multiqueue packet
schedulers, also from Eric Dumazet.
23) Fix MAC and unicast list handling in bnxt_en driver, from Jeffrey
Huang and Michael Chan.
24) Don't actively scan radar channels, from Antonio Quartulli"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (110 commits)
net: phy: reset only targeted phy
bnxt_en: Setup uc_list mac filters after resetting the chip.
bnxt_en: enforce proper storing of MAC address
bnxt_en: Fixed incorrect implementation of ndo_set_mac_address
net: lpc_eth: remove irq > NR_IRQS check from probe()
net_sched: fix qdisc_tree_decrease_qlen() races
openvswitch: fix hangup on vxlan/gre/geneve device deletion
ipv4: igmp: Allow removing groups from a removed interface
ipv6: sctp: implement sctp_v6_destroy_sock()
arm64: bpf: add 'store immediate' instruction
ipv6: kill sk_dst_lock
ipv6: sctp: add rcu protection around np->opt
net/neighbour: fix crash at dumping device-agnostic proxy entries
sctp: use GFP_USER for user-controlled kmalloc
sctp: convert sack_needed and sack_generation to bits
ipv6: add complete rcu protection around np->opt
bpf: fix allocation warnings in bpf maps and integer overflow
mvebu: dts: enable IP checksum with jumbo frames for Armada 38x on Port0
net: mvneta: enable setting custom TX IP checksum limit
net: mvneta: fix error path for building skb
...
Pull block fixes from Jens Axboe:
"A collection of fixes from this series. The most important here is a
regression fix for an issue that some folks would hit in blk-merge.c,
and the NVMe queue depth limit for the screwed up Apple "nvme"
controller.
In more detail, this pull request contains:
- a set of fixes for null_blk, including a fix for a few corner cases
where we could hang the device. From Arianna and Paolo.
- lightnvm:
- A build improvement from Keith.
- Update the qemu pci id detection from Matias.
- Error handling fixes for leaks and other little fixes from
Sudip and Wenwei.
- fix from Eric where BLKRRPART would not return EBUSY for whole
device mounts, only when partitions were mounted.
- fix from Jan Kara, where EOF O_DIRECT reads would return
negatively.
- remove check for rq_mergeable() when checking limits for cloned
requests. The check doesn't make any sense. It's assuming that
since NOMERGE is set on the request that we don't have to
recalculate limits since the request didn't change, but that's not
true if the request has been redirected. From Hannes.
- correctly get the bio front segment value set for single segment
bio's, fixing a BUG() in blk-merge. From Ming"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvme: temporary fix for Apple controller reset
null_blk: change type of completion_nsec to unsigned long
null_blk: guarantee device restart in all irq modes
null_blk: set a separate timer for each command
blk-merge: fix computing bio->bi_seg_front_size in case of single segment
direct-io: Fix negative return from dio read beyond eof
block: Always check queue limits for cloned requests
lightnvm: missing nvm_lock acquire
lightnvm: unconverted ppa returned in get_bb_tbl
lightnvm: refactor and change vendor id for qemu
lightnvm: do device max sectors boundary check first
lightnvm: fix ioctl memory leaks
lightnvm: free memory when gennvm register fails
lightnvm: Simplify config when disabled
Return EBUSY from BLKRRPART for mounted whole-dev fs
events on pids. It filters all events where only tasks with their pid in that
file exists. It also handles the sched_switch and sched_wakeup trace events
where the current task does not have its pid in the file, but the task
either being switched to or awaken does.
Unfortunately, I forgot about sched_wakeup_new and sched_waking. Both of
these tracepoints use the same class as the sched_wakeup tracepoint, and
they too should be included in what gets filtered by the set_event_pid file.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWX7XpAAoJEKKk/i67LK/8G6gH/0W9QxCt/iS+J+x3gAPPs+/9
jtwZgAOWjq+118ZpWORtgRcoH2r/sJUNwlXqhMojAHsPlwZsr6TXkWJkgyNdZZ7B
QdUtZrr+egGYvd7TE0ONi/XrLTe9VLtBQsh5pN7l9fF9TjxYUmu5V9LplH9z0RxW
Hw8EzqGzG2iZnXYCnErtu5jRLmr18f2u9aUptPAc4bYPLVUUw9M9MqRV/ZwQxsaX
1mfIoR5SVC5IWW/R07qjULlbFpvNXkVJ56HwXMVBN44mYz3eUGYBKzjyAJ0Ugymf
CNDPzh4HgVFsEqDedr0D8T5WZNJSUErdbHVSWze+CCUNfYikvU7gNmxNJ89Q3P4=
=LsnU
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"During the merge window I added a new file that is used to filter
trace events on pids. It filters all events where only tasks with
their pid in that file exists. It also handles the sched_switch and
sched_wakeup trace events where the current task does not have its pid
in the file, but the task either being switched to or awaken does.
Unfortunately, I forgot about sched_wakeup_new and sched_waking. Both
of these tracepoints use the same class as the sched_wakeup
tracepoint, and they too should be included in what gets filtered by
the set_event_pid file"
* tag 'trace-v4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Add sched_wakeup_new and sched_waking tracepoints for pid filter
* fix scanning in mac80211 to not actively scan radar
channels (from Antonio)
* fix uninitialized variable in remain-on-channel that
could lead to treating frame TX as remain-on-channel
and not sending the frame at all
* remove NL80211_FEATURE_FULL_AP_CLIENT_STATE again, it
was broken and needs more work, we'll enable it later
* fix call_rcu() induced use-after-reset/free in mesh
(that was suddenly causing issues in certain tests)
* always request block-ack window size 64 as we found
some APs will otherwise crash (really ...)
* fix P2P-Device teardown sequence to avoid restarting
with uninitialized data
-----BEGIN PGP SIGNATURE-----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=vui7
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2015-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A small set of fixes for 4.4:
* fix scanning in mac80211 to not actively scan radar
channels (from Antonio)
* fix uninitialized variable in remain-on-channel that
could lead to treating frame TX as remain-on-channel
and not sending the frame at all
* remove NL80211_FEATURE_FULL_AP_CLIENT_STATE again, it
was broken and needs more work, we'll enable it later
* fix call_rcu() induced use-after-reset/free in mesh
(that was suddenly causing issues in certain tests)
* always request block-ack window size 64 as we found
some APs will otherwise crash (really ...)
* fix P2P-Device teardown sequence to avoid restarting
with uninitialized data
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to address another chip on same MDIO bus. The case is
correctly handled for media advertising. It is taken into account
only if mii_data->phy_id == phydev->addr. However, this condition
was missing for reset case.
Signed-off-by: Jérôme Pouiller <jezz@sysmic.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: set mac address and uc_list bug fixes.
Fix ndo_set_mac_address() for PF and VF.
Re-apply uc_list after chip reset.
v2: Fix compile error if CONFIG_BNXT_SRIOV is not set.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Call bnxt_cfg_rx_mode() in bnxt_init_chip() to setup uc_list and
mc_list mac address filters. Before the patch, uc_list is not
setup again after chip reset (such as ethtool ring size change)
and macvlans don't work any more after that.
Modify bnxt_cfg_rx_mode() to return error codes appropriately so
that the init chip sequence can detect any failures.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For PF, the bp->pf.mac_addr always holds the permanent MAC
addr assigned by the HW. For VF, the bp->vf.mac_addr always
holds the administrator assigned VF MAC addr. The random
generated VF MAC addr should never get stored to bp->vf.mac_addr.
This way, when the VF wants to change the MAC address, we can tell
if the adminstrator has already set it and disallow the VF from
changing it.
v2: Fix compile error if CONFIG_BNXT_SRIOV is not set.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing ndo_set_mac_address only copies the new MAC addr
and didn't set the new MAC addr to the HW. The correct way is
to delete the existing default MAC filter from HW and add
the new one. Because of RFS filters are also dependent on the
default mac filter l2 context, the driver must go thru
close_nic() to delete the default MAC and RFS filters, then
open_nic() to set the default MAC address to HW.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver is used on an ARM platform with SPARSE_IRQ defined,
semantics of NR_IRQS is different (minimal value of virtual irqs) and
by default it is set to 16, see arch/arm/include/asm/irq.h.
This value may be less than the actual number of virtual irqs, which
may break the driver initialization. The check removal allows to use
the driver on such a platform, and, if irq controller driver works
correctly, the check is not needed on legacy platforms.
Fixes a runtime problem:
lpc-eth 31060000.ethernet: error getting resources.
lpc_eth: lpc-eth: not found (-6).
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qdisc_tree_decrease_qlen() suffers from two problems on multiqueue
devices.
One problem is that it updates sch->q.qlen and sch->qstats.drops
on the mq/mqprio root qdisc, while it should not : Daniele
reported underflows errors :
[ 681.774821] PAX: sch->q.qlen: 0 n: 1
[ 681.774825] PAX: size overflow detected in function qdisc_tree_decrease_qlen net/sched/sch_api.c:769 cicus.693_49 min, count: 72, decl: qlen; num: 0; context: sk_buff_head;
[ 681.774954] CPU: 2 PID: 19 Comm: ksoftirqd/2 Tainted: G O 4.2.6.201511282239-1-grsec #1
[ 681.774955] Hardware name: ASUSTeK COMPUTER INC. X302LJ/X302LJ, BIOS X302LJ.202 03/05/2015
[ 681.774956] ffffffffa9a04863 0000000000000000 0000000000000000 ffffffffa990ff7c
[ 681.774959] ffffc90000d3bc38 ffffffffa95d2810 0000000000000007 ffffffffa991002b
[ 681.774960] ffffc90000d3bc68 ffffffffa91a44f4 0000000000000001 0000000000000001
[ 681.774962] Call Trace:
[ 681.774967] [<ffffffffa95d2810>] dump_stack+0x4c/0x7f
[ 681.774970] [<ffffffffa91a44f4>] report_size_overflow+0x34/0x50
[ 681.774972] [<ffffffffa94d17e2>] qdisc_tree_decrease_qlen+0x152/0x160
[ 681.774976] [<ffffffffc02694b1>] fq_codel_dequeue+0x7b1/0x820 [sch_fq_codel]
[ 681.774978] [<ffffffffc02680a0>] ? qdisc_peek_dequeued+0xa0/0xa0 [sch_fq_codel]
[ 681.774980] [<ffffffffa94cd92d>] __qdisc_run+0x4d/0x1d0
[ 681.774983] [<ffffffffa949b2b2>] net_tx_action+0xc2/0x160
[ 681.774985] [<ffffffffa90664c1>] __do_softirq+0xf1/0x200
[ 681.774987] [<ffffffffa90665ee>] run_ksoftirqd+0x1e/0x30
[ 681.774989] [<ffffffffa90896b0>] smpboot_thread_fn+0x150/0x260
[ 681.774991] [<ffffffffa9089560>] ? sort_range+0x40/0x40
[ 681.774992] [<ffffffffa9085fe4>] kthread+0xe4/0x100
[ 681.774994] [<ffffffffa9085f00>] ? kthread_worker_fn+0x170/0x170
[ 681.774995] [<ffffffffa95d8d1e>] ret_from_fork+0x3e/0x70
mq/mqprio have their own ways to report qlen/drops by folding stats on
all their queues, with appropriate locking.
A second problem is that qdisc_tree_decrease_qlen() calls qdisc_lookup()
without proper locking : concurrent qdisc updates could corrupt the list
that qdisc_match_from_root() parses to find a qdisc given its handle.
Fix first problem adding a TCQ_F_NOPARENT qdisc flag that
qdisc_tree_decrease_qlen() can use to abort its tree traversal,
as soon as it meets a mq/mqprio qdisc children.
Second problem can be fixed by RCU protection.
Qdisc are already freed after RCU grace period, so qdisc_list_add() and
qdisc_list_del() simply have to use appropriate rcu list variants.
A future patch will add a per struct netdev_queue list anchor, so that
qdisc_tree_decrease_qlen() can have more efficient lookups.
Reported-by: Daniele Fucini <dfucini@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Cong Wang <cwang@twopensource.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each openvswitch tunnel vport (vxlan,gre,geneve) holds a reference
to the underlying tunnel device, but never released it when such
device is deleted.
Deleting the underlying device via the ip tool cause the kernel to
hangup in the netdev_wait_allrefs() loop.
This commit ensure that on device unregistration dp_detach_port_notify()
is called for all vports that hold the device reference, properly
releasing it.
Fixes: 614732eaa1 ("openvswitch: Use regular VXLAN net_device device")
Fixes: b2acd1dc39 ("openvswitch: Use regular GRE net_device instead of vport")
Fixes: 6b001e682e ("openvswitch: Use Geneve device.")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Flavio Leitner <fbl@sysclose.org>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The non-PCI builds of the O day test project are failing:
On Thu, 2015-12-03 at 05:02 +0800, kbuild test robot wrote:
> warning: (SCSI_MPT2SAS) selects SCSI_MPT3SAS which has unmet direct
> dependencies (SCSI_LOWLEVEL && PCI && SCSI)
The problem is that select and depend don't interact because Kconfig doesn't
have a SAT solver, so depend picks up dependencies and select does onward
selects, but select doesn't pick up dependencies. To fix this, we need to add
the correct dependencies to the MPT2SAS option like this.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: b840c3627b
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When a multicast group is joined on a socket, a struct ip_mc_socklist
is appended to the sockets mc_list containing information about the
joined group.
If the interface is hot unplugged, this entry becomes stale. Prior to
commit 52ad353a53 ("igmp: fix the problem when mc leave group") it
was possible to remove the stale entry by performing a
IP_DROP_MEMBERSHIP, passing either the old ifindex or ip address on
the interface. However, this fix enforces that the interface must
still exist. Thus with time, the number of stale entries grows, until
sysctl_igmp_max_memberships is reached and then it is not possible to
join and more groups.
The previous patch fixes an issue where a IP_DROP_MEMBERSHIP is
performed without specifying the interface, either by ifindex or ip
address. However here we do supply one of these. So loosen the
restriction on device existence to only apply when the interface has
not been specified. This then restores the ability to clean up the
stale entries.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 52ad353a53 "(igmp: fix the problem when mc leave group")
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Vyukov reported a memory leak using IPV6 SCTP sockets.
We need to call inet6_destroy_sock() to properly release
inet6 specific fields.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth 2015-12-01
Here's a Bluetooth fix for the 4.4-rc series that fixes a memory leak of
the Security Manager L2CAP channel that'll happen for every LE
connection.
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
aarch64 doesn't have native store immediate instruction, such operation
has to be implemented by the below instruction sequence:
Load immediate to register
Store register
Signed-off-by: Yang Shi <yang.shi@linaro.org>
CC: Zi Shen Lim <zlim.lnx@gmail.com>
CC: Xi Wang <xi.wang@gmail.com>
Reviewed-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing the np->opt RCU conversion, I found that UDP/IPv6 was
using a mixture of xchg() and sk_dst_lock to protect concurrent changes
to sk->sk_dst_cache, leading to possible corruptions and crashes.
ip6_sk_dst_lookup_flow() uses sk_dst_check() anyway, so the simplest
way to fix the mess is to remove sk_dst_lock completely, as we did for
IPv4.
__ip6_dst_store() and ip6_dst_store() share same implementation.
sk_setup_caps() being called with socket lock being held or not,
we have to use sk_dst_set() instead of __sk_dst_set()
Note that I had to move the "np->dst_cookie = rt6_get_cookie(rt);"
in ip6_dst_store() before the sk_setup_caps(sk, dst) call.
This is because ip6_dst_store() can be called from process context,
without any lock held.
As soon as the dst is installed in sk->sk_dst_cache, dst can be freed
from another cpu doing a concurrent ip6_dst_store()
Doing the dst dereference before doing the install is needed to make
sure no use after free would trigger.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch completes the work I did in commit 45f6fad84c
("ipv6: add complete rcu protection around np->opt"), as I missed
sctp part.
This simply makes sure np->opt is used with proper RCU locking
and accessors.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because accounting resources for the root cgroup sometimes incurs
measureable overhead for workloads which don't care about cgroup and
often ends up calculating a number which is available elsewhere in a
slightly different form, cgroup is not in the business of providing
system-wide statistics. The pids controller which was introduced
recently was exposing "pids.current" at the root. This patch disable
accounting for root cgroup and removes the file from the root
directory.
While this is a userland visible behavior change, pids has been
available only in one version and was badly broken there, so I don't
think this will be noticeable. If it turns out to be a problem, we
can reinstate it for v1 hierarchies.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Aleksa Sarai <cyphar@cyphar.com>
Consider the following v2 hierarchy.
P0 (+memory) --- P1 (-memory) --- A
\- B
P0 has memory enabled in its subtree_control while P1 doesn't. If
both A and B contain processes, they would belong to the memory css of
P1. Now if memory is enabled on P1's subtree_control, memory csses
should be created on both A and B and A's processes should be moved to
the former and B's processes the latter. IOW, enabling controllers
can cause atomic migrations into different csses.
The core cgroup migration logic has been updated accordingly but the
controller migration methods haven't and still assume that all tasks
migrate to a single target css; furthermore, the methods were fed the
css in which subtree_control was updated which is the parent of the
target csses. pids controller depends on the migration methods to
move charges and this made the controller attribute charges to the
wrong csses often triggering the following warning by driving a
counter negative.
WARNING: CPU: 1 PID: 1 at kernel/cgroup_pids.c:97 pids_cancel.constprop.6+0x31/0x40()
Modules linked in:
CPU: 1 PID: 1 Comm: systemd Not tainted 4.4.0-rc1+ #29
...
ffffffff81f65382 ffff88007c043b90 ffffffff81551ffc 0000000000000000
ffff88007c043bc8 ffffffff810de202 ffff88007a752000 ffff88007a29ab00
ffff88007c043c80 ffff88007a1d8400 0000000000000001 ffff88007c043bd8
Call Trace:
[<ffffffff81551ffc>] dump_stack+0x4e/0x82
[<ffffffff810de202>] warn_slowpath_common+0x82/0xc0
[<ffffffff810de2fa>] warn_slowpath_null+0x1a/0x20
[<ffffffff8118e031>] pids_cancel.constprop.6+0x31/0x40
[<ffffffff8118e0fd>] pids_can_attach+0x6d/0xf0
[<ffffffff81188a4c>] cgroup_taskset_migrate+0x6c/0x330
[<ffffffff81188e05>] cgroup_migrate+0xf5/0x190
[<ffffffff81189016>] cgroup_attach_task+0x176/0x200
[<ffffffff8118949d>] __cgroup_procs_write+0x2ad/0x460
[<ffffffff81189684>] cgroup_procs_write+0x14/0x20
[<ffffffff811854e5>] cgroup_file_write+0x35/0x1c0
[<ffffffff812e26f1>] kernfs_fop_write+0x141/0x190
[<ffffffff81265f88>] __vfs_write+0x28/0xe0
[<ffffffff812666fc>] vfs_write+0xac/0x1a0
[<ffffffff81267019>] SyS_write+0x49/0xb0
[<ffffffff81bcef32>] entry_SYSCALL_64_fastpath+0x12/0x76
This patch fixes the bug by removing @css parameter from the three
migration methods, ->can_attach, ->cancel_attach() and ->attach() and
updating cgroup_taskset iteration helpers also return the destination
css in addition to the task being migrated. All controllers are
updated accordingly.
* Controllers which don't care whether there are one or multiple
target csses can be converted trivially. cpu, io, freezer, perf,
netclassid and netprio fall in this category.
* cpuset's current implementation assumes that there's single source
and destination and thus doesn't support v2 hierarchy already. The
only change made by this patchset is how that single destination css
is obtained.
* memory migration path already doesn't do anything on v2. How the
single destination css is obtained is updated and the prep stage of
mem_cgroup_can_attach() is reordered to accomodate the change.
* pids is the only controller which was affected by this bug. It now
correctly handles multi-destination migrations and no longer causes
counter underflow from incorrect accounting.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-tested-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Cc: Aleksa Sarai <cyphar@cyphar.com>
If one or more tasks get moved into a frozen css, the frozen state is
cleared up from the destination css so that it can be reasserted once
the migrated tasks are frozen. freezer_attach() implements this in
two separate steps - clearing CGROUP_FROZEN on the target css while
processing each task and propagating the clearing upwards after the
task loop is done if necessary.
This patch merges the two steps. Propagation now takes place inside
the task loop. This simplifies the code and prepares it for the fix
of multi-destination migration.
Signed-off-by: Tejun Heo <tj@kernel.org>
Contrary to what the datasheet says, the pre divider doesn't seem to be
incremented by one in the PLL2, but just uses the value from the register,
with 0 being a bypass.
This fixes the audio playing too fast.
Since we now have the same pre-divider flags, and the only difference with
the A10 is the post-divider offset, also remove the structure to just pass
the offset as an argument.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fixes: eb662f8547 ("clk: sunxi: pll2: Add A13 support")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Proxy entries could have null pointer to net-device.
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Fixes: 84920c1420 ("net: Allow ipv6 proxies and arp proxies be shown with iproute2")
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Vyukov reported that the user could trigger a kernel warning by
using a large len value for getsockopt SCTP_GET_LOCAL_ADDRS, as that
value directly affects the value used as a kmalloc() parameter.
This patch thus switches the allocation flags from all user-controllable
kmalloc size to GFP_USER to put some more restrictions on it and also
disables the warn, as they are not necessary.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
They don't need to be any bigger than that and with this we start a new
bitfield for tracking association runtime stuff, like zero window
situation.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses multiple problems :
UDP/RAW sendmsg() need to get a stable struct ipv6_txoptions
while socket is not locked : Other threads can change np->opt
concurrently. Dmitry posted a syzkaller
(http://github.com/google/syzkaller) program desmonstrating
use-after-free.
Starting with TCP/DCCP lockless listeners, tcp_v6_syn_recv_sock()
and dccp_v6_request_recv_sock() also need to use RCU protection
to dereference np->opt once (before calling ipv6_dup_options())
This patch adds full RCU protection to np->opt
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don Zickus