Tegra would not only need a hardware vblank counter that
increments at leading edge of vblank, but also support
for instantaneous high precision vblank timestamp queries, ie.
a proper implementation of dev->driver->get_vblank_timestamp().
Without these, there can be off-by-one errors during vblank
disable/enable if the scanout is inside vblank at en/disable
time, and additionally clients will never see any useable
vblank timestamps when querying via drmWaitVblank ioctl. This
would negatively affect swap scheduling under X11 and Wayland.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
At present, dma_buf_export() takes a series of parameters, which
makes it difficult to add any new parameters for exporters, if required.
Make it simpler by moving all these parameters into a struct, and pass
the struct * as parameter to dma_buf_export().
While at it, unite dma_buf_export_named() with dma_buf_export(), and
change all callers accordingly.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Perhaps the most noteworthy change in this set is the implementation of
a hardware VBLANK counter using host1x syncpoints. The SOR registers can
now be dumped via debugfs, which can be useful while debugging. The IOVA
address space maintained by the driver can also be dumped via debugfs.
Other than than, these changes are mostly cleanup work, such as making
register names more consistent or removing unused code (that was left
over after the atomic mode-setting conversion). There's also a fix for
eDP that makes the driver cope with firmware that already initialized
the display (such as the firmware on the Tegra-based Chromebooks).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=HZO1
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.1-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.1-rc1
Perhaps the most noteworthy change in this set is the implementation of
a hardware VBLANK counter using host1x syncpoints. The SOR registers can
now be dumped via debugfs, which can be useful while debugging. The IOVA
address space maintained by the driver can also be dumped via debugfs.
Other than than, these changes are mostly cleanup work, such as making
register names more consistent or removing unused code (that was left
over after the atomic mode-setting conversion). There's also a fix for
eDP that makes the driver cope with firmware that already initialized
the display (such as the firmware on the Tegra-based Chromebooks).
* tag 'drm/tegra/for-4.1-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: sor: Reset during initialization
drm/tegra: gem: Return 64-bit offset for mmap(2)
drm/tegra: hdmi: Name register fields consistently
drm/tegra: hdmi: Resets are synchronous
drm/tegra: dc: Document tegra_dc_state_setup_clock()
drm/tegra: dc: Remove unused callbacks
drm/tegra: dc: Remove unused function
drm/tegra: dc: Use base atomic state helpers
drm/atomic: Add helpers for state-subclassing drivers
drm/tegra: dc: Implement hardware VBLANK counter
gpu: host1x: Export host1x_syncpt_read()
drm/tegra: sor: Dump registers via debugfs
drm/tegra: sor: Registers are 32-bit
drm/tegra: Provide debugfs file for the IOVA space
drm/tegra: dc: Check for valid parent clock
As there isn't a way for the firmware on the Nyan Chromebooks to hand
over the display to the kernel, and the kernel isn't redoing the whole
configuration at present.
With this patch, the SOR is brought to a known state and we get correct
display on every boot.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This function is called by output drivers so should be documented. While
at it, move it to a more appropriate location.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ->mode_set() and ->mode_set_base() callbacks are no longer used with
full atomic mode-setting drivers, so remove them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The tegra_dc_setup_clock() function is unused after the conversion to
atomic mode-setting, so remove it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Instead of duplicating the code, make use of the newly introduced atomic
state duplicate and destroy helpers. This allows changes to the base
atomic state handling to automatically propagate to the Tegra driver and
thereby prevent breakage resulting from both copies going out of sync.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The display controller on Tegra can use syncpoints to count VBLANK
events. syncpoints are 32-bit unsigned integers, so well suited as
VBLANK counters.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use a sized unsigned 32-bit data type (u32) to store register contents.
The SOR registers are 32 bits wide irrespective of the architecture's
data width.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra DRM driver uses a single IO virtual address space for buffer
mappings. Provide a table of the address space usage in debugfs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Check that the desired parent clock is indeed a valid parent for the
display controller clock. This is purely cosmetic at this point since
the parent clocks are specified in DT and all the currently defined
parents are in fact valid parents of the display controller clock.
Signed-off-by: Thierry Reding <treding@nvidia.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU/NacAAoJEHm+PkMAQRiGdUcIAJU5dHclwd9HRc7LX5iOwYN6
mN0aCsYjMD8Pjx2VcPCgJvkIoESQO5pkwYpFFWCwILup1bVEidqXfr8EPOdThzdh
kcaT0FwUvd19K+0jcKVNCX1RjKBtlUfUKONk6sS2x4RrYZpv0Ur8Gh+yXV8iMWtf
fAusNEYlxQJvEz5+NSKw86EZTr4VVcykKLNvj+/t/JrXEuue7IG8EyoAO/nLmNd2
V/TUKKttqpE6aUVBiBDmcMQl2SUVAfp5e+KJAHmizdDpSE80nU59UC1uyV8VCYdM
qwHXgttLhhKr8jBPOkvUxl4aSXW7S0QWO8TrMpNdEOeB3ZB8AKsiIuhe1JrK0ro=
=Xkue
-----END PGP SIGNATURE-----
Merge tag 'v4.0-rc3' into drm-next
Linux 4.0-rc3 backmerge to fix two i915 conflicts, and get
some mainline bug fixes needed for my testing box
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/intel_display.c
Use cases like rotation require these hooks to have some context so they
know how to prepare and cleanup the frame buffer correctly.
For i915 specifically, object backing pages need to be mapped differently
for different rotation modes and the driver needs to know which mapping to
instantiate and which to tear down when transitioning between them.
v2: Made passed in states const. (Daniel Vetter)
[airlied: add mdp5 and atmel fixups]
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These names only make sense because of backwards compatability with
the order used by the crtc helper library. There's not really any real
requirement in the ordering here.
So rename them to something more descriptive and update the kerneldoc
a bit. Motivated in a discussion with Laurent about how to restore
plane state for dpms for drivers with runtime pm.
v2: Squash in fixup from Stephen Rothwell to fix a conflict with
tegra.
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The code in tegra_crtc_prepare() really belongs in tegra_dc_init(), or
at least most of it. This fixes an issue with VBLANK handling because
tegra_crtc_prepare() would overwrite the interrupt mask register that
tegra_crtc_enable_vblank() had written to to enable VBLANK interrupts.
Tested-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Store a pointer to the CRTC in its atomic state to make it easy for
state handling code to get at the CRTC.
Tested-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit eab3bbeffd ("drm/atomic: Add drm_crtc_state->active") added the
field to track the DPMS state. However, the Tegra driver was in modified
in parallel and subclasses the CRTC atomic state, so needed to duplicate
the code in the atomic helpers. After the addition of the active_changed
field it became out of sync and doesn't reset it when duplicating state.
This causes a full modeset on things like page-flips, which will in turn
cause warnings due to the VBLANK machinery being disabled when it really
should remain on.
Tested-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Recent changes in the clock framework have caused a behavioural change
in that clocks that have not had their rate set explicitly will now be
reset to their initial rate (or 0) when the clock is released. This is
triggered in the deferred probing path, resulting in the clock running
at a wrong frequency after the successful probe.
This can be easily fixed by setting the rate explicitly rather than by
relying on the implicit rate inherited by the parent.
Tested-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When copying a relocation from userspace, copy the correct target
offset.
Signed-off-by: David Ung <davidu@nvidia.com>
Fixes: 961e3beae3 ("drm/tegra: Make job submission 64-bit safe")
Cc: stable@vger.kernel.org
[treding@nvidia.com: provide a better commit message]
Signed-off-by: Thierry Reding <treding@nvidia.com>
For now only disable the KMS hotplug polling helper logic upon suspend
and re-enable it on resume.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Previously output drivers would enable continuous display mode and power
up the display controller at various points during the initialization.
This is suboptimal because it accesses display controller registers in
output drivers and duplicates a bit of code.
Move this code into the display controller driver and enable the display
controller as the final step of the ->mode_set_nofb() implementation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tracking these in the plane state allows them to be computed in the
->atomic_check() callback and reused when applying the configuration in
->atomic_update().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Wrap struct drm_crtc_state in a driver-specific structure and add the
planes field which keeps track of which planes are updated or disabled
during a modeset. This allows atomic updates of the the display engine
at ->atomic_flush() time.
v2: open-code getting the state of the CRTC that the plane is being
attached to (Daniel Vetter)
Signed-off-by: Thierry Reding <treding@nvidia.com>
All output drivers have now been converted to use the ->atomic_check()
callback, so the ->mode_fixup() callbacks are no longer used.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Provide a custom ->atomic_commit() implementation which supports async
commits. The generic atomic page-flip helper can use this to implement
page-flipping.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Replace drm_crtc_helper_set_config() by drm_atomic_helper_set_config().
All drivers have now been converted to use ->atomic_check() to set the
atomic state, therefore the atomic mode setting helpers can be used.
Signed-off-by: Thierry Reding <treding@nvidia.com>
All clock state is now stored in the display controller's atomic state,
so the output drivers no longer need to call back into the display
controller driver to set up the clock. This is also required to make
sure no hardware changes are made before validating a configuration.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The implementation of the ->atomic_check() callback precomputes all
parameters to check if the given configuration can be applied. If so the
precomputed values are stored in the atomic state object for the encoder
and applied during modeset. In that way the modeset no longer needs to
perform any checking but simply program values into registers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The implementation of the ->atomic_check() callback precomputes all
parameters to check if the given configuration can be applied. If so the
precomputed values are stored in the atomic state object for the encoder
and applied during modeset. In that way the modeset no longer needs to
perform any checking but simply program values into registers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The implementation of the ->atomic_check() callback precomputes all
parameters to check if the given configuration can be applied. If so the
precomputed values are stored in the atomic state object for the encoder
and applied during modeset. In that way the modeset no longer needs to
perform any checking but simply program values into registers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The implementation of the ->atomic_check() callback precomputes all
parameters to check if the given configuration can be applied. If so the
precomputed values are stored in the atomic state object for the encoder
and applied during modeset. In that way the modeset no longer needs to
perform any checking but simply program values into registers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This allows the clock setup to be separated from the clock programming
and better matches the expectations of the atomic modesetting where no
code paths must fail during modeset.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Switch out the regular plane helpers for the atomic plane helpers. Also
use the default atomic helpers to implement the ->atomic_check() and
->atomic_commit() callbacks. The driver now exclusively uses the atomic
interfaces.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Hook up the default ->reset() and ->atomic_duplicate_state() helpers.
This ensures that state objects are properly created and framebuffer
reference counts correctly maintained.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement initial atomic state handling. Hook up the CRTCs, planes' and
connectors' ->atomic_destroy_state() callback to ensure that the atomic
state objects don't leak.
Furthermore the CRTC now implements the ->mode_set_nofb() callback that
is used by new helpers to implement ->mode_set() and ->mode_set_base().
These new helpers also make use of the new plane helper functions which
the driver now provides.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit 9c0127004f ("drm/tegra: dc: Add powergate support") changed the
driver's ->probe() implementation to deassert the module reset, and with
there being nobody else to assert it until ->remove() there is no need
to deassert again later on.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The tegra_output midlayer is now completely gone and output drivers use
it purely as a helper library.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The debugfs cleanup code never fails, so no error is returned. Therefore
the functions can all return void instead.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement encoder and connector within the eDP driver itself using the
Tegra output helpers rather than using the Tegra output as midlayer. By
doing so one level of indirection is removed and output drivers become
more flexible while keeping the majority of the advantages provided by
the common output helpers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement encoder and connector within the DSI driver itself using the
Tegra output helpers rather than using the Tegra output as midlayer. By
doing so one level of indirection is removed and output drivers become
more flexible while keeping the majority of the advantages provided by
the common output helpers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement encoder and connector within the HDMI driver itself using the
Tegra output helpers rather than using the Tegra output as midlayer. By
doing so one level of indirection is removed and output drivers become
more flexible while keeping the majority of the advantages provided by
the common output helpers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement encoder and connector within the RGB driver itself using the
Tegra output helpers rather than using the Tegra output as midlayer. By
doing so one level of indirection is removed and output drivers become
more flexible while keeping the majority of the advantages provided by
the common output helpers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This is a small helper that performs the basic steps required by all
output drivers to prepare the display controller for use with a given
encoder.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to transition output drivers to using the struct tegra_output
as a helper rather than midlayer, make this callback optional. Instead
drivers should implement the equivalent as part of ->mode_fixup(). For
the conversion to atomic modesetting a new callback ->atomic_check()
should be implemented that updates the display controller's state with
the corresponding parent clock, rate and shift clock divider.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The output layer was initially designed to help reduce the amount of
code duplicated in output drivers. An unfortunate side-effect of that
was that it turned into a midlayer and it became difficult to make the
output drivers work without bending over backwards to fit into the
midlayer.
This commit starts to convert the midlayer into a helper library by
exporting most of the common functions so that they can be used by the
output drivers directly. Doing so will allow output drivers to reuse
common code paths but more easily override them where necessary.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DRM core should take care of disabling all unneeded planes, so there
is no need to do this explicitly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This structure will be extended using non-framebuffer related callbacks
in subsequent patches, so it should move to a more central location.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When disabling the display controller, stop it and wait for it to become
idle. Doing so ensures that no further accesses to the framebuffer occur
and the buffers can be safely unmapped or freed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Previously output drivers would all stop the display controller in their
disable path. However with the transition to atomic modesetting the
display controller needs to be kept running until all planes have been
disabled so that software can properly determine (using VBLANK counts)
when it is safe to remove the framebuffers associated with the planes.
Moving this code into the display controller's disable path also gets
rid of the duplication of this into all output drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
All output drivers have open-coded variants of this function, so export
it to remove some code duplication.
Signed-off-by: Thierry Reding <treding@nvidia.com>
kfree(ERR_PTR(-ENOMEM)) will not work very well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
We can't save two values to the IRQ flags at the same time so the IRQs
are not enabled at the end. This kind of bug is easy to miss in testing
if the function is normally called with IRQs disabled so we wouldn't
enable IRQs anyway.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Compliance testing shows that HS Trail is off by -12%. Increase the HS
Trail time to make this test pass.
Signed-off-by: David Ung <davidu@nvidia.com>
[treding@nvidia.com: update specification references, add comment]
Signed-off-by: Thierry Reding <treding@nvidia.com>
This allows a DRM driver unload/reload cycle to completely reset the DSI
controller and may help in situations where it's broken.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use a sized unsigned 32-bit data type (u32) to store register contents.
The DSI registers are 32 bits wide irrespective of the architecture's
data width.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use a sized unsigned 32-bit data type (u32) to store register contents.
The HDMI registers are 32 bits wide irrespective of the architecture's
data width.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Most of the display controller's registers are double-buffered, a few of
them are triple-buffered. The ASSEMBLY shadow copy is latched intto the
ACTIVE copy for double-buffered registers. For triple-buffered registers
the ASSEMBLY copy is first latched into the ARM copy.
Latching into the ACTIVE copy happens immediately if the controller is
inactive. Otherwise the latching happens on the next frame boundary. The
latching of the ASSEMBLY into the ARM copy happens immediately. Latching
is controlled by a set of *_ACT_REQ and *_UPDATE bits in the
DC_CMD_STATE_CONTROL register.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra114 and earlier support specifying the color of the border (i.e.
the active area of the screen that is not covered by any of the overlay
windows). By default this is set to a light blue, so set it to black to
comply with the requirements set by atomic modesetting.
Signed-off-by: Thierry Reding <treding@nvidia.com>
iommu_domain_alloc() returns NULL on error, it never returns error
pointers.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The possible_crtcs mask needs to be a mask of CRTC indices. There is no
guarantee that the DRM indices match the hardware pipe number, so the
mask must be computed from the CRTC index.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DRM core now zeroes out the memory associated with CRTC, encoder and
connector objects upon cleanup, so there's no need to explicitly do that
in drivers anymore.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Previously the struct bus_type exported by the host1x infrastructure was
only a very basic skeleton. Turn that implementation into a more full-
fledged bus to support proper probe ordering and power management.
Note that the bus infrastructure needs to be available before any of the
drivers can be registered. This is automatically ensured if all drivers
are built as loadable modules (via symbol dependencies). If all drivers
are built-in there are no such guarantees and the link order determines
the initcall ordering. Adjust drivers/gpu/Makefile to make sure that the
host1x bus infrastructure is initialized prior to any of its users (only
drm/tegra currently).
v2: Fix building host1x and tegra-drm as modules
Reported-by: Dave Airlie <airlied@gmail.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Misc drm patches with mostly polish patches from Thierry, with a bit of
generic mode validation from Ville and a few other oddball things.
* tag 'topic/core-stuff-2014-12-19' of git://anongit.freedesktop.org/drm-intel: (25 commits)
drm: Include drm_crtc_helper.h in DocBook
drm: Make drm_crtc_helper.h standalone includible
drm: Move IRQ related fields to proper section
drm: Remove stale comment
drm: Do basic sanity checks for user modes
drm: Perform basic sanity checks on probed modes
drm: Reorganize probed mode validation
drm/doc: Remove duplicate "by"
drm/info: Remove unused code
drm/cache: Use wbinvd helpers
drm/plane-helper: Test for plane disable earlier
drm/doc: Document drm_add_modes_noedid() usage
drm: bit of spell-check / editorializing.
drm: Prefer sizeof(type) over sizeof type
drm: Remove useless else block
drm: Remove unneeded braces for single statement blocks
drm: Do not assign in if condition
drm: Prefer kmalloc_array() over kmalloc() with multiply
drm: Prefer kcalloc() over kzalloc() with multiply
drm: Miscellaneous checkpatch whitespace cleanups
...
In finish pageflip, the driver was not selecting the root window when
dispatching events. This exposed a race where a plane update would
change the window selection and cause tegra_dc_finish_page_flip to check
the wrong base address.
This patch also protects access to the window selection register as well
as the registers affected by it.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If the requested buffer size wasn't a multiple of the page size, the
IOMMU code would round down the size to the next multiple of the page
size, thereby causing translation errors. To fix this we no longer pass
around the requested size but reuse the computed size of the GEM object.
This is already rounded to the next page boundary, so mapping that size
works out fine.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Buffers obtained via shmem may still have associated cachelines. If they
aren't properly flushed they may cause framebuffer corruption if the
cache gets flushed after the application has drawn to it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Page-flip completion could race with page-flip submission, so extend the
critical section to include all accesses to page-flip related data.
Reported-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The hardware pipe numbers don't always match the DRM CRTC indices. This
can happen for example if the first display controller defers probe,
causing it to be registered with DRM after the second display
controller. When that happens the hardware pipe numbers and DRM CRTC
indices become different. Make sure that the CRTC index is always used
when accessing per-CRTC VBLANK data. This can be ensured by using the
drm_crtc_vblank_*() API, which will do the right thing automatically
given a struct drm_crtc *.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ->load_lut() callback is optional, therefore a dummy implementation
is not needed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The highlights in this pull request are:
* IOMMU support: The Tegra DRM driver can now deal with discontiguous
buffers if an IOMMU exists in the system. That means it can allocate
using drm_gem_get_pages() and will map them into IOVA space via the
IOMMU API. Similarly, non-contiguous PRIME buffers can be imported
from a different driver, which allows better integration with gk20a
(nouveau) and less hacks.
* Universal planes: This is precursory work for atomic modesetting and
will allow hardware cursor support to be implemented on pre-Tegra114
where RGB cursors were not supported.
* DSI ganged-mode support: The DSI controller can now gang up with a
second DSI controller to drive high resolution DSI panels.
Besides those bigger changes there is a slew of fixes, cleanups, plugged
memory leaks and so on.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=v4QW
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-3.19-rc1' of git://people.freedesktop.org/~tagr/linux into drm-next
drm/tegra: Changes for v3.19-rc1
The highlights in this pull request are:
* IOMMU support: The Tegra DRM driver can now deal with discontiguous
buffers if an IOMMU exists in the system. That means it can allocate
using drm_gem_get_pages() and will map them into IOVA space via the
IOMMU API. Similarly, non-contiguous PRIME buffers can be imported
from a different driver, which allows better integration with gk20a
(nouveau) and less hacks.
* Universal planes: This is precursory work for atomic modesetting and
will allow hardware cursor support to be implemented on pre-Tegra114
where RGB cursors were not supported.
* DSI ganged-mode support: The DSI controller can now gang up with a
second DSI controller to drive high resolution DSI panels.
Besides those bigger changes there is a slew of fixes, cleanups, plugged
memory leaks and so on.
* tag 'drm/tegra/for-3.19-rc1' of git://people.freedesktop.org/~tagr/linux: (44 commits)
drm/tegra: gem: Check before freeing CMA memory
drm/tegra: fb: Add error codes to error messages
drm/tegra: fb: Properly release GEM objects on failure
drm/tegra: Detach panel when a connector is removed
drm/tegra: Plug memory leak
drm/tegra: gem: Use more consistent data types
drm/tegra: fb: Do not destroy framebuffer
drm/tegra: gem: dumb: pitch and size are outputs
drm/tegra: Enable the hotplug interrupt only when necessary
drm/tegra: dc: Universal plane support
drm/tegra: dc: Registers are 32 bits wide
drm/tegra: dc: Factor out DC, window and cursor commit
drm/tegra: Add IOMMU support
drm/tegra: Fix error handling cleanup
drm/tegra: gem: Use dma_mmap_writecombine()
drm/tegra: gem: Remove redundant drm_gem_free_mmap_offset()
drm/tegra: gem: Cleanup tegra_bo_create_with_handle()
drm/tegra: gem: Extract tegra_bo_alloc_object()
drm/tegra: dsi: Set up PHY_TIMING & BTA_TIMING registers earlier
drm/tegra: dsi: Replace 1000000 by USEC_PER_SEC
...
dma_free_writecombine() must not be called on a buffer that couldn't be
allocated. Check for a valid virtual address before attempting to free
the memory to avoid a crash.
Reported-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When fbdev initialization fails, make sure to unreference the GEM
objects properly. Note that we can't do this in the general error
unwinding path because ownership of the GEM object references is
transferred to the framebuffer upon creation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When the DRM device is torn down and the connector is removed, make sure
to detach the panel to make sure there are no dangling pointers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Drop a reference instead of directly calling the framebuffer .destroy()
callback at fbdev free time. This is necessary to make sure the object
isn't destroyed if anyone else still has a reference.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When creating a dumb buffer object using the DRM_IOCTL_MODE_CREATE_DUMB
IOCTL, only the width, height, bpp and flags parameters are inputs. The
caller is not guaranteed to zero out or set handle, pitch and size, so
the driver must not treat these values as possible inputs.
Fixes a bug where running the Weston compositor on Tegra DRM would cause
an attempt to allocate a 3 GiB framebuffer to be allocated.
Fixes: de2ba664c3 ("gpu: host1x: drm: Add memory manager and fb")
Cc: stable@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
The hotplug handling needs access to the DRM device, which only appears
at ->init() time. Disable interrupts up until that time. Similarly, when
an output is removed, disable the hotplug interrupt again because the
DRM device (and with it the hotplug infrastructure) is going away.
Also make sure to only access the DRM device if it's available. Given
the above change for the hotplug interrupt this should really never
happen, but the extra check doesn't hurt either.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This allows the primary plane and cursor to be exposed as regular
DRM/KMS planes, which is a prerequisite for atomic modesetting and gives
userspace more flexibility over controlling them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Using an unsigned long type will cause these variables to become 64-bit
on 64-bit SoCs. In practice this should always work, but there's no need
for carrying around the additional 32 bits.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The sequence to commit changes to the DC, window or cursor configuration
is repetitive and can be extracted into separate functions for ease of
use.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When an IOMMU device is available on the platform bus, allocate an IOMMU
domain and attach the display controllers to it. The display controllers
can then scan out non-contiguous buffers by mapping them through the
IOMMU.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DRM driver's ->load() implementation didn't do a good job (no job at
all really) cleaning up on failure. Fix that by undoing any prior setup
when an error occurs. This requires a bit of rework to make it possible
to clean up fbdev midway.
This was tested by injecting errors at various points during the
initialization sequence and verifying that error cleanup didn't crash
and no memory leaked (using kmemleak).
Reported-by: Stéphane Marchesin <marcheu@chromium.org>
Reported-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The drm_gem_object_release() function already performs this cleanup, so
there is no reason to do it explicitly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
There is only a single location where the function needs to do cleanup.
Skip the error unwinding path and call the cleanup function directly
instead.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This function implements the common buffer object allocation used for
both allocation and import paths.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Make sure the DSI PHY_TIMING and BTA_TIMING registers are initialized
when the clocks are set up as opposed to when the output is enabled.
This makes sure that the PHY timings are properly set up when the panel
is prepared and that DCS commands sent at that time use the appropriate
timings.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for sending MIPI DSI command packets from the host to a
peripheral. This is required for panels that need configuration before
they accept video data.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement ganged mode support for the Tegra DSI driver. The DSI host
controller to gang up with is specified via a phandle in the device tree
and the resolved DSI host controller used for the programming of the
ganged-mode registers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In preparation for adding ganged-mode support, this commit splits out
the tegra_dsi_set_timeout() function so that it can be reused for the
slave DSI controller.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for DC-driven command mode. This is a mode where the video
stream sent by the display controller is packed into DCS command packets
(write_memory_start and write_memory_continue) by the DSI controller. It
can be used for panels with a remote framebuffer and is useful to save
power when used with a dynamic refresh rate (not yet supported by the
driver).
Signed-off-by: Thierry Reding <treding@nvidia.com>
For command mode panels, the DSI controller needs to be enabled and
configured so that panel drivers can send commands prior to the video
stream being enabled.
Move code from the monolithic output enable/disable functions into
smaller, reusable units to allow more fine-grained control over the
controller state.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The driver wasn't even attempting to do any cleanup when probing failed.
Fix this by releasing any resources acquired up to the point of failure
and putting the device back into the original state (reset, clocks off).
Signed-off-by: Thierry Reding <treding@nvidia.com>
DSI panels can always be hotplugged via the DSI bus' attach/detach
infrastructure, so unconditionally mark the connector hotpluggable.
While at it, also make sure that when a panel is detached the connector
is marked unconnected before calling into the DRM hotplug helpers to
reflect the correct state.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The common clock framework will take care of preparing and enabling the
parent of the DSI clock automatically.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In preparation for supporting command mode panels, don't disable the
clock when the output is disabled. The output will be enabled only after
the panel has been programmed in command mode, so the clock must always
remain on.
As a side-effect, pad calibration now only needs to be done at driver
probe time, since neither power nor controller state will go away before
driver removal. While at it, use a 32-bit variable to store register
content because the registers are 32-bit even on 64-bit Tegra.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rather than hardcoding them as macros, make the host and video FIFO
depths parameters so that they can be more easily adjusted if a new
generation of the Tegra SoC changes them.
While at it, set the depth of the video FIFO to the correct value of
1920 *words* rather than *bytes*.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Previously the panel and output were only enabled on encoder->dpms(). If
userspace called dpms on before doing a modeset, the driver would get into
a state where the connector had a dpms state of ON, but the encoder and output
were not enabled (because the encoder is not yet attached to the connector).
Subsequent dpms ON calls are ignored b/c the connector's state already matches
the desired state.
This patch enables/disables the panel and output on modeset as well, so we
can catch the above case.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Both display controllers are in their own power partition. Currently the
driver relies on the assumption that these partitions are on (which is
the hardware default). However some bootloaders may disable them, so the
driver must make sure to turn them back on to avoid hangs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The introduction of the COMPILE_TEST dependency in commit 158b50aefa
(drm/tegra: Increase compile test coverage) removes the dependency on
COMMON_CLK (implicitly selected via ARCH_TEGRA, ARCH_MULTI_V7 and
ARCH_MULTIPLATFORM).
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When the CRTC is enabled, make sure the VBLANK machinery is enabled.
Failure to do so will cause drm_vblank_get() to not enable the VBLANK on
the CRTC and VBLANK-synchronized page-flips won't work.
While at it, get rid of the legacy drm_vblank_pre_modeset() and
drm_vblank_post_modeset() calls that are replaced by drm_vblank_on()
and drm_vblank_off().
Reported-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Just a bit of OCD cleanup on headers - this function isn't the core
interface any more but just a helper for drivers who haven't yet
transitioned to universal planes. Put the declaration at the right
spot and sprinkle necessary #includes over all drivers.
Maybe this helps to encourage driver maintainers to do the switch.
v2: Fix #include ordering for tegra, reported by 0-day builder.
v3: Include required headers, reported by Thierry.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Thierry Reding <treding@nvidia.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
v2: Don't forget git add, noticed by David.
Cc: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Rename the defines to have levels instead of values for vswing and
pre-emph levels as the values may differ in other scenarios like low vswing of
eDP1.4 where the values are different.
Done using following cocci patch for each define:
@@
@@
# define DP_TRAIN_VOLTAGE_SWING_400 (0 << 0)
+ # define DP_TRAIN_VOLTAGE_SWING_LEVEL_0 (0 << 0)
...
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This merge window brings a good size of cleanups on various
platforms. Among the bigger ones:
* Removal of Samsung s5pc100 and s5p64xx platforms. Both of these have
lacked active support for quite a while, and after asking around nobody
showed interest in keeping them around. If needed, they could be
resurrected in the future but it's more likely that we would prefer
reintroduction of them as DT and multiplatform-enabled platforms
instead.
* OMAP4 controller code register define diet. They defined a lot of registers
that were never actually used, etc.
* Move of some of the Tegra platform code (PMC, APBIO, fuse, powergate)
to drivers/soc so it can be shared with 64-bit code. This also converts them
over to traditional driver models where possible.
* Removal of legacy gpio-samsung driver, since the last users have been
removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some misc
cleanups, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=gbcE
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This merge window brings a good size of cleanups on various platforms.
Among the bigger ones:
- Removal of Samsung s5pc100 and s5p64xx platforms. Both of these
have lacked active support for quite a while, and after asking
around nobody showed interest in keeping them around. If needed,
they could be resurrected in the future but it's more likely that
we would prefer reintroduction of them as DT and
multiplatform-enabled platforms instead.
- OMAP4 controller code register define diet. They defined a lot of
registers that were never actually used, etc.
- Move of some of the Tegra platform code (PMC, APBIO, fuse,
powergate) to drivers/soc so it can be shared with 64-bit code.
This also converts them over to traditional driver models where
possible.
- Removal of legacy gpio-samsung driver, since the last users have
been removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some
misc cleanups, etc"
* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
drivers: CCI: Correct use of ! and &
video: clcd-versatile: Depend on ARM
video: fix up versatile CLCD helper move
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
MAINTAINERS: Remove Kirkwood
ARM: tegra: Convert PMC to a driver
soc/tegra: fuse: Set up in early initcall
ARM: tegra: Always lock the CPU reset vector
ARM: tegra: Setup CPU hotplug in a pure initcall
soc/tegra: Implement runtime check for Tegra SoCs
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
...
Pull DRM updates from Dave Airlie:
"Like all good pull reqs this ends with a revert, so it must mean we
tested it,
[ Ed. That's _one_ way of looking at it ]
This pull is missing nouveau, Ben has been stuck trying to track down
a very longstanding bug that revealed itself due to some other
changes. I've asked him to send you a direct pull request for nouveau
once he cleans things up. I'm away until Monday so don't want to
delay things, you can make a decision on that when he sends it, I have
my phone so I can ack things just not really merge much.
It has one trivial conflict with your tree in armada_drv.c, and also
the pull request contains some component changes that are already in
your tree, the base tree from Russell went via Greg's tree already,
but some stuff still shows up in here that doesn't when I merge my
tree into yours.
Otherwise all pretty standard graphics fare, one new driver and
changes all over the place.
New drivers:
- sti kms driver for STMicroelectronics chipsets stih416 and stih407.
core:
- lots of cleanups to the drm core
- DP MST helper code merged
- universal cursor planes.
- render nodes enabled by default
panel:
- better panel interfaces
- new panel support
- non-continuous cock advertising ability
ttm:
- shrinker fixes
i915:
- hopefully ditched UMS support
- runtime pm fixes
- psr tracking and locking - now enabled by default
- userptr fixes
- backlight brightness fixes
- MST support merged
- runtime PM for dpms
- primary planes locking fixes
- gen8 hw semaphore support
- fbc fixes
- runtime PM on SOix sleep state hw.
- mmio base page flipping
- lots of vlv/chv fixes.
- universal cursor planes
radeon:
- Hawaii fixes
- display scalar support for non-fixed mode displays
- new firmware format support
- dpm on more asics by default
- GPUVM improvements
- uncached and wc GTT buffers
- BOs > visible VRAM
exynos:
- i80 interface support
- module auto-loading
- ipp driver consolidated.
armada:
- irq handling in crtc layer only
- crtc renumbering
- add component support
- DT interaction changes.
tegra:
- load as module fixes
- eDP bpp and sync polarity fixed
- DSI non-continuous clock mode support
- better support for importing buffers from nouveau
msm:
- mdp5/adq8084 v1.3 hw enablement
- devicetree clk changse
- ifc6410 board working
tda998x:
- component support
- DT documentation update
vmwgfx:
- fix compat shader namespace"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (551 commits)
Revert "drm: drop redundant drm_file->is_master"
drm/panel: simple: Use devm_gpiod_get_optional()
drm/dsi: Replace upcasting macro by function
drm/panel: ld9040: Replace upcasting macro by function
drm/exynos: dp: Modify driver to support drm_panel
drm/exynos: Move DP setup into commit()
drm/panel: simple: Add AUO B133HTN01 panel support
drm/panel: simple: Support delays in panel functions
drm/panel: simple: Add proper definition for prepare and unprepare
drm/panel: s6e8aa0: Add proper definition for prepare and unprepare
drm/panel: ld9040: Add proper definition for prepare and unprepare
drm/tegra: Add support for panel prepare and unprepare routines
drm/exynos: dsi: Add support for panel prepare and unprepare routines
drm/exynos: dpi: Add support for panel prepare and unprepare routines
drm/panel: simple: Add dummy prepare and unprepare routines
drm/panel: s6e8aa0: Add dummy prepare and unprepare routines
drm/panel: ld9040: Add dummy prepare and unprepare routines
drm/panel: Provide convenience wrapper for .get_modes()
drm/panel: add .prepare() and .unprepare() functions
drm/panel: simple: Remove simple-panel compatible
...
Mostly some cleanup all over the place. Pitch alignment limitations of
the display controller are now honored and job submission is 64-bit
safe.
The SOR output (used for eDP) properly configures sync signal polarities
according to the display mode rather than hard-coding them to some value
and the number of bits per color is now taken from the panel rather than
hard-coded to properly support 24-bit vs. 18-bit panels.
The DSI controller now properly supports non-continuous clock mode.
GEM objects can now have their flags and tiling mode modified via IOCTLs
to allow buffers imported from Nouveau to be properly displayed. Newer
generations of the Tegra display controller can also detile block linear
buffers at scan-out time.
Finally the driver now properly exports MODULE_DEVICE_TABLEs to allow it
to be automatically loaded when built as a module.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=qYgE
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-3.17-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v3.17-rc1
Mostly some cleanup all over the place. Pitch alignment limitations of
the display controller are now honored and job submission is 64-bit
safe.
The SOR output (used for eDP) properly configures sync signal polarities
according to the display mode rather than hard-coding them to some value
and the number of bits per color is now taken from the panel rather than
hard-coded to properly support 24-bit vs. 18-bit panels.
The DSI controller now properly supports non-continuous clock mode.
GEM objects can now have their flags and tiling mode modified via IOCTLs
to allow buffers imported from Nouveau to be properly displayed. Newer
generations of the Tegra display controller can also detile block linear
buffers at scan-out time.
Finally the driver now properly exports MODULE_DEVICE_TABLEs to allow it
to be automatically loaded when built as a module.
* tag 'drm/tegra/for-3.17-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: add MODULE_DEVICE_TABLEs
drm/tegra: dc - Reset controller on driver remove
drm/tegra: Properly align stride for framebuffers
drm/tegra: sor - Configure proper sync polarities
drm/tegra: sor - Use bits-per-color from panel
drm/tegra: Make job submission 64-bit safe
drm/tegra: Allow non-authenticated processes to create buffer objects
drm/tegra: Add SET/GET_FLAGS IOCTLs
drm/tegra: Add SET/GET_TILING IOCTLs
drm/tegra: Implement more tiling modes
drm/tegra: dsi - Handle non-continuous clock flag
drm/tegra: sor - missing unlock on error
Panels can now be more finely controlled via .prepare() and .unprepare()
callbacks in addition to .enable() and .disable(). New kerneldoc details
what they are supposed to do and when they should be called.
The simple panel driver gained support for a couple of new panels and it
is now possible to specify additional delays during power up and power
down sequences if panels require it.
DSI devices can now advertise that they support non-continuous clock
mode which will allow DSI host controllers to disable the high speed
clock after transmissions to save power.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vf7m
-----END PGP SIGNATURE-----
Merge tag 'drm/panel/for-3.17-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/panel: Changes for v3.17-rc1
Panels can now be more finely controlled via .prepare() and .unprepare()
callbacks in addition to .enable() and .disable(). New kerneldoc details
what they are supposed to do and when they should be called.
The simple panel driver gained support for a couple of new panels and it
is now possible to specify additional delays during power up and power
down sequences if panels require it.
DSI devices can now advertise that they support non-continuous clock
mode which will allow DSI host controllers to disable the high speed
clock after transmissions to save power.
* tag 'drm/panel/for-3.17-rc1' of git://anongit.freedesktop.org/tegra/linux: (30 commits)
drm/panel: simple: Use devm_gpiod_get_optional()
drm/dsi: Replace upcasting macro by function
drm/panel: ld9040: Replace upcasting macro by function
drm/exynos: dp: Modify driver to support drm_panel
drm/exynos: Move DP setup into commit()
drm/panel: simple: Add AUO B133HTN01 panel support
drm/panel: simple: Support delays in panel functions
drm/panel: simple: Add proper definition for prepare and unprepare
drm/panel: s6e8aa0: Add proper definition for prepare and unprepare
drm/panel: ld9040: Add proper definition for prepare and unprepare
drm/tegra: Add support for panel prepare and unprepare routines
drm/exynos: dsi: Add support for panel prepare and unprepare routines
drm/exynos: dpi: Add support for panel prepare and unprepare routines
drm/panel: simple: Add dummy prepare and unprepare routines
drm/panel: s6e8aa0: Add dummy prepare and unprepare routines
drm/panel: ld9040: Add dummy prepare and unprepare routines
drm/panel: Provide convenience wrapper for .get_modes()
drm/panel: add .prepare() and .unprepare() functions
drm/panel: simple: Remove simple-panel compatible
drm/panel: simple: Add Innolux N116BGE panel support
...
Modify tegra output driver to support the new panel calls:
prepare and unprepare.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When tegra-drm.ko is built as a module, these MODULE_DEVICE_TABLEs allow
the module to be auto-loaded since the module will match the devices
instantiated from device tree.
(Notes for stable: in 3.14+, just git rm any conflicting file, since they
are added in later kernels. For 3.13 and below, manual merging will be
needed)
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Since the device will no longer be used, may as well keep it in reset to
potentially save some power and make sure it is in a clean state the
next time it's probed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra20 and Tegra30 both required the buffer line stride to be aligned
on 8 byte boundaries. Tegra114 and Tegra124 increased the alignment to
64 bytes. Introduce a parameter to specify the alignment requirements
for each display controller and round up the pitch of newly allocated
framebuffers appropriately.
Originally-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This change uses the value of bits-per-color from panel to remove one
more hardcoded value.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Job submission currently relies on the fact that struct drm_tegra_reloc
and struct host1x_reloc are the same size and uses a simple call to the
copy_from_user() function to copy them to kernel space. This causes the
handle to be stored in the buffer object field, which then needs a cast
to a 32 bit integer to resolve it to a proper buffer object pointer and
store it back in the buffer object field.
On 64-bit architectures that will no longer work, since pointers are 64
bits wide whereas handles will remain 32 bits. This causes the sizes of
both structures to because different and copying will no longer work.
Fix this by adding a new function, host1x_reloc_get_user(), that copies
the structures field by field.
While at it, use substructures for the command and target buffers in
struct host1x_reloc for better readability. Also use unsized types to
make it more obvious that this isn't part of userspace ABI.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This matches what other drivers do for equivalent IOCTLs.
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DRM_TEGRA_GEM_SET_FLAGS IOCTL can be used to set the flags of a
buffer object after it has been allocated or imported. Flags associated
with a buffer object can be queried using the DRM_TEGRA_GEM_GET_FLAGS
IOCTL.
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently the tiling parameters of buffer objects can only be set at
allocation time, and only a single tiled mode is supported. This new
DRM_TEGRA_GEM_SET_TILING IOCTL allows more modes to be set and also
allows the tiling mode to be changed after the allocation. This will
enable the Tegra DRM driver to import buffers from a GPU and directly
scan them out by configuring the display controller appropriately.
To complement this, the DRM_TEGRA_GEM_GET_TILING IOCTL can query the
current tiling mode of a buffer object. This is necessary when importing
buffers via handle (as is done in Mesa for example) so that userspace
can determine the proper parameters for the 2D or 3D engines.
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra124 supports a block-linear mode in addition to the regular pitch
linear and tiled modes. Add support for these by moving the internal
representation into a structure rather than a simple flag.
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Handle the MIPI_DSI_CLOCK_NONCONTINUOUS flag and only set TX-only
clock behavior when this flag is present to allow panels requiring
continuous clock mode to operate with this driver.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
We should unlock before returning the error code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit converts the PMC support code to a platform driver. Because
the boot process needs to call into this driver very early, also set up
a minimal environment via an early initcall.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to not clutter the include/linux directory with SoC specific
headers, move the Tegra-specific headers out into a separate directory.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This allows reservation objects to be used in dma-buf. it's required
for implementing polling support on the fences that belong to a dma-buf.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com> #drivers/media/v4l2-core/
Acked-by: Thomas Hellstrom <thellstrom@vmware.com> #drivers/gpu/drm/ttm
Acked-by: Sumit Semwal <sumit.semwal@linaro.org>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net> #drivers/gpu/drm/armada/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A race condition currently exists on Tegra, where it can happen that a
monitor attached via HDMI isn't detected during the initial FB helper
setup, but the hotplug event happens too early to be processed by the
poll helpers because they haven't been initialized yet. This happens
because on some boards the HDMI driver can control the regulator that
supplies the +5V pin on the HDMI connector. Therefore depending on the
timing between the initialization of the HDMI driver and the rest of
DRM, it's possible that the monitor returns the hotplug signal right
within the window where we would miss it.
Unfortunately, drm_kms_helper_poll_init() will wreak havoc when called
before at least some parts of the FB helpers have been set up.
This commit fixes this by splitting out the minimum of initialization
required to make drm_kms_helper_poll_init() work into a separate
function that can be called early. It is then safe to move all of the
poll helper initialization to an earlier point in time (before the
HDMI output driver has a chance to enable the +5V supply). That way if
the hotplug signal is returned before the initial FB helper setup, the
monitor will be forcefully detected at that point, and if the hotplug
signal is returned after that it will be properly handled by the poll
helpers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
To implement hotplug detection in a race-free manner, drivers must call
drm_kms_helper_poll_init() before hotplug events can be triggered. Such
events can be triggered right after any of the encoders or connectors
are initialized. At the same time, if the drm_fb_helper_hotplug_event()
helper is used by a driver, then the poll helper requires some parts of
the FB helper to be initialized to prevent a crash.
At the same time, drm_fb_helper_init() requires information that is not
necessarily available at such an early stage (number of CRTCs and
connectors), so it cannot be used yet.
Add a new helper, drm_fb_helper_prepare(), that initializes the bare
minimum needed to allow drm_kms_helper_poll_init() to execute and any
subsequent hotplug events to be processed properly.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There's no need for this to be modifiable. Make it const so that it can
be put into the .rodata section.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Introduce generic functions to register and unregister connectors. This
provides a common place to add and remove associated user space
interfaces.
Signed-off-by: Thomas Wood <thomas.wood@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to the DP specification the disparity of the first symbol
should always be negative. It is therefore safe to assume that panels
will conform to that and therefore parameterizing this field should
never be necessary.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The number of HBLANK and VBLANK symbols can be computed at runtime so
that they can be set appropriately depending on the video mode and DP
link.
These values are used by the packet generation logic to determine how
many audio samples can be transferred during the blanking intervals.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The currently hardcoded link parameters don't work on all eDP panels, so
compute the parameters at runtime depending on the mode and panel type
to allow the driver to cope with a wider variety of panels.
Note that the number of bits per pixel of the panel is still hardcoded,
but this can be addressed in a separate patch.
This is largely based on a patch by Stéphane Marchesin but the algorithm
was largely rewritten to be more readable and concise.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Lanes are powered up in decreasing order. Power them down in increasing
order for consistency.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The comment above mentions link A/B but this isn't what the code does,
so let's fix that.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The code currently rounds up the clock to the next MHZ, which is
rounding up a 69.5MHz clock to 70MHz on my machine. This in turn
prevents the display from syncing. Removing this rounding fixes eDP
for me.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Other output drivers set up debugfs slightly differently. Bring the SOR
driver in line with those for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Removing only the root directory will fail when there are still files in
it. Instead of manually removing all files, remove the whole directory
recursively.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Doing so allows the hotplug events generated by the connector to be
properly handled by the DRM poll helpers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Calling the drm_helper_hpd_irq_event() helper can sleep, so instead of
invoking it directly from the interrupt handler, schedule a work queue
and run it from there.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable hardware cursor support on Tegra124. Earlier generations support
the hardware cursor to some degree as well, but not in a way that can be
generically exposed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DRM core can now cope with drivers that don't have an associated
struct drm_bus, so the host1x implementation is no longer useful.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra124 is mostly backwards-compatible with Tegra114. However, Tegra124
supports a few more features (e.g. interlacing, ...). Introduce a new
compatible string and TMDS tables to cope with these differences.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Accessing the CRC debugfs file will hang the system if the SOR is not
enabled, so make sure that it is stays enabled until the CRC has been
read.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In some cases the pixel clock used to not be correct, which is why it
had to be recomputed. It turns out that the reason why it wasn't correct
is that it was used wrongly. If used correctly there's not need for the
recomputation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The shift clock divider is highly dependent on the type of output, so
push computation of it down into the output drivers. The old code used
to work merely by accident.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Program the shift clock divider in tegra_crtc_setup_clk() since that's
where the divider is computed, so passing it around can be avoided.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Assert the DSI controller's reset when the driver is unloaded to reduce
power consumption and to put the controller into a known state for
subsequent driver reloads.
Signed-off-by: Thierry Reding <treding@nvidia.com>
To prevent the enable or disable operations to potentially be run
multiple times, add guards to return early when the output is already
in the targetted state.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The packet sequencer needs to be programmed depending on the video mode
of the attached peripheral. Add support for non-burst video modes with
sync events (as opposed to sync pulses) and select either sequence
depending on the video mode.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DSI controllers are powered by a (typically 1.2V) regulator. Usually
this is always on, so there was no need to support enabling or disabling
it thus far. But in order not to consume any power when DSI is inactive,
give the driver a chance to enable or disable the supply as needed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
A bunch of registers are initialized to 0 upon during driver probe. It
turns out that none of these are actually needed, so they can simply be
dropped.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The pixel format enumeration values used by the Tegra DSI controller
don't match those defined by the DSI framework. Make sure to convert
them to the internal format before writing it to the register.
Signed-off-by: Thierry Reding <treding@nvidia.com>
For some reason when the PW*_ENABLE and PM*_ENABLE fields are cleared
during disable, the HDMI output stops working properly. Resetting and
initializing doesn't help.
Comment out those accesses for now until it has been determined what to
do about them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Disable LVDS mode according to register documentation. It seems like
this has no effect on the operation of HDMI, but it's probably a good
idea to do this anyway.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This reflects the power-up sequence as described in the documentation,
but it doesn't seem to be strictly necessary to get HDMI to work.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Clocks are never enabled or disabled in atomic context, so we can use
the clk_prepare_enable() and clk_disable_unprepare() helpers instead.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The generic Tegra output code already sets up the clocks properly, so
there's no need to do it again when the HDMI output is enabled.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Revert commit 18ebc0f404 "drm/tegra: hdmi: Enable VDD earlier for
hotplug/DDC" and instead add a new supply for the +5V pin on the HDMI
connector.
The vdd-supply property refers to the regulator that supplies the
AVDD_HDMI input on Tegra, rather than the +5V HDMI connector pin. This
was never a problem before, because all boards had that pin hooked up to
a regulator that was always on. Starting with Dalmore and continuing
with Venice2, the +5V pin is controllable via a GPIO. For reasons
unknown, the GPIO ended up as the controlling GPIO of the AVDD_HDMI
supply in the Dalmore and Venice2 DTS files. But that's not correct.
Instead, a separate supply must be introduced so that the +5V pin can be
controlled separately from the supplies that feed the HDMI block within
Tegra.
A new hdmi-supply property is introduced that takes the place of the
vdd-supply and vdd-supply is only enabled when HDMI is enabled rather
than all the time.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Setting the bits in this register is dependent on the output type driven
by the display controller. All output drivers already set these properly
so there is no need to do it here again.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The tegra_dc_format() and tegra_dc_setup_window() functions are only
used internally by the display controller driver. Move them upwards in
order to make them static and get rid of the function prototypes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
V_DIRECTION is the name of the field in the documentation, so use that
for consistency. Also add the H_DIRECTION field for completeness.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR allows the computation of a 32 bit CRC of the content that it
transmits. This functionality is exposed via debugfs and is useful to
verify proper operation of the SOR.
Signed-off-by: Thierry Reding <treding@nvidia.com>
YUYV is UYVY with swapped bytes. Luckily the Tegra DC hardware can swap
bytes during scan-out, so supporting YUYV is simply a matter of writing
the correct value to the byteswap register.
This patch modifies tegra_dc_format() to return the byte swap parameter
via an output parameter in addition to returning the pixel format. Many
other formats can potentially be supported in a similar way.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Remove extern keyword from function prototypes since it isn't needed and
drop an unnecessary forward declaration.
Signed-off-by: Thierry Reding <treding@nvidia.com>
All drm_fb_helper_restore_fbdev_mode() call sites, save one, do the same
locking. Simplify this into drm_fb_helper_restore_fbdev_mode_unlocked().
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This should avoid races between connector probing and HPD
irqs in the future, currently mode_config.mutex blocks this
possibility.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Next pull request, this time more of the drm de-midlayering work. The big
thing is that his patch series here removes everything from drm_bus except
the set_busid callback. Thierry has a few more patches on top of this to
make that one optional to.
With that we can ditch all the non-pci drm_bus implementations, which
Thierry has already done for the fake tegra host1x drm_bus.
Reviewed by Thierry, Laurent and David and now also survived some testing
on my intel boxes to make sure the irq fumble is fixed correctly ;-) The
last minute rebase was just to add the r-b tags from Thierry for the 2
patches I've redone.
* 'drm-init-cleanup' of git://people.freedesktop.org/~danvet/drm:
drm/<drivers>: don't set driver->dev_priv_size to 0
drm: Remove dev->kdriver
drm: remove drm_bus->get_name
drm: rip out dev->devname
drm: inline drm_pci_set_unique
drm: remove bus->get_irq implementations
drm: pass the irq explicitly to drm_irq_install
drm/irq: Look up the pci irq directly in the drm_control ioctl
drm/irq: track the irq installed in drm_irq_install in dev->irq
drm: rename dev->count_lock to dev->buf_lock
drm: Rip out totally bogus vga_switcheroo->can_switch locking
drm: kill drm_bus->bus_type
drm: remove drm_dev_to_irq from drivers
drm/irq: remove cargo-culted locking from irq_install/uninstall
drm/irq: drm_control is a legacy ioctl, so pci devices only
drm/pci: fold in irq_by_busid support
drm/irq: simplify irq checks in drm_wait_vblank
A single fix for some framebuffer reference counting fallout caused by
the primary plane helpers introduced in 3.15-rc1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=uM53
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-3.15-rc3' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Fixes for v3.15-rc3
A single fix for some framebuffer reference counting fallout caused by
the primary plane helpers introduced in 3.15-rc1.
* tag 'drm/tegra/for-3.15-rc3' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: restrict plane loops to legacy planes
In Matt Ropers primary plane series a set of prep patches like
commit af2b653bfb
Author: Matt Roper <matthew.d.roper@intel.com>
Date: Tue Apr 1 15:22:32 2014 -0700
drm/i915: Restrict plane loops to only operate on overlay planes (v2)
ensured that all exisiting users of the mode_config->plane_list
wouldn't change behaviour. Unfortunately tegra seems to have fallen
through the cracks. Fix it.
This regression was introduced in
commit e13161af80
Author: Matt Roper <matthew.d.roper@intel.com>
Date: Tue Apr 1 15:22:38 2014 -0700
drm: Add drm_crtc_init_with_planes() (v2)
The result was that we've unref'ed the fb for the primary plane twice,
leading to a use-after free bug. This is because the drm core will
already set crtc->primary->fb to NULL and do the unref for us, and the
crtc disable hook is called by the drm crtc helpers for exactly this
case.
Aside: Now that the fbdev helpers clean up planes there's no longer a
need to do this in drivers. So this could probably be nuked entirely
in linux-next.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This was only ever used to pretty-print the irq driver name. And on
kms systems due to set_version bonghits we never set up the prettier
name, ever. Which make this a bit pointless.
Also, we can always dig out the driver-instance/irq relationship
through other means, so this isn't that useful. So just rip it out to
simplify the set_version/set_busid insanity a bit.
Also delete the temporary busname from drm_pci_set_busid, it's now
unused.
v2: Rebase on top of the new host1x drm_bus for tegra.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Completely unused. Hooray, midlayer mistakes that didn't cause work to
undo!
v2: Rebase on top of the recent tegra changes which added a host1x drm
bus.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Certain types of I2C-over-AUX transactions require that only the address
is transferred. Detect this by looking at the AUX message's size and set
the address-only bit appropriately.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement eDP support for Tegra124 and support the PRIME vmap()/vunmap()
operations.
A symbol that is required for upcoming V4L2 support is now exported by
the host1x driver.
Relicense drivers under the GPL v2 for consistency. One exception is the
public header file, which is relicensed under MIT to abide by the common
rule.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=LGu0
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-3.15-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v3.15-rc1
Implement eDP support for Tegra124 and support the PRIME vmap()/vunmap()
operations.
A symbol that is required for upcoming V4L2 support is now exported by
the host1x driver.
Relicense drivers under the GPL v2 for consistency. One exception is the
public header file, which is relicensed under MIT to abide by the common
rule.
* tag 'drm/tegra/for-3.15-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: Use standard GPL v2 license text
drm/tegra: Relicense under GPL v2
drm/tegra: Relicense public header under MIT
drm/tegra: Add eDP support
gpu: host1x: export host1x_syncpt_incr_max() function
drm/tegra: prime: Add vmap support
Use the more canonical and concise variant of the GPL v2 license text.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The majority of the code in this driver is licensed under the GPL v2, so
relicense the rest under GPL v2 as well for consistency.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for eDP functionality found on Tegra124 and later SoCs. Only
fast link training is currently supported.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Now that CRTC's have a primary plane, there's no need to track the
framebuffer in the CRTC. Replace all references to the CRTC fb with the
primary plane's fb.
This patch was generated by the Coccinelle semantic patching tool using
the following rules:
@@ struct drm_crtc C; @@
- (C).fb
+ C.primary->fb
@@ struct drm_crtc *C; @@
- (C)->fb
+ C->primary->fb
v3: Generate patch via coccinelle. Actual removal of crtc->fb has been
moved to a subsequent patch.
v2: Fixup several lingering crtc->fb instances that were missed in the
first patch iteration. [Rob Clark]
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTJlUvAAoJEHm+PkMAQRiGOhYH/1I+Bc7N7Rjr6QQAtBIy0GPC
XMqSE/gpgxlvRneQbQsvTUlPnWRhgzLGendT9HFKawkaQ0UNuZdRVyBHGFmpuED8
RlbicVVuuEZabrxEnCd7UPvYvEyK5pLIFpCRs5B+ManB1qLki2Ar03ymH1NRxOde
edmPbSUFo2aONITrEBm7tqT3cShTmBaDGP/zU0TNDMNrpVVDbHZolSNu2z4xOTa5
GqAOEbluLQ6jP3yxWur/V3Lk3W7pB6TabfX4o6UZu0F3iFnJxRMIzHXrI3o4yLTj
HEwmB3npfc8DIUk4oik7RkN+aqxDcdg/rBLQD63+xxt6zCkP+0q16brC0R67qWE=
=n9Ml
-----END PGP SIGNATURE-----
Merge tag 'v3.14-rc7' into drm-next
Linux 3.14-rc7
Backmerge to help out Intel guys.
Mario Kleiner