Commit Graph

159 Commits

Author SHA1 Message Date
Huaxu Wan 39d5e0ce0f iwlwifi: clear the translate table area
Driver should clear the translate table area after receiving "Alive"
response from uCode. This patch corrects a mistake when doing this.

Signed-off-by: Huaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: Guo Chaohong <chaohong.guo@linux.intel.com>
Acked-by: Ben M Cahill  <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-07 16:39:44 -04:00
Wey-Yi Guy d8c07e7a84 iwlwifi: Chain Noise Calibration for 6000 series
Adding support of Chain Noise Calibration for 6000 series NICs.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-07 16:39:36 -04:00
Wey-Yi Guy 2f748decee iwlwifi: send cmd to uCode to configure valid tx antenna
In order for uCode to select the valid antennas for transmit, driver
need to configure the allowed tx antennas through host command.

The TX_ANT_CONFIGURATION_CMD should be used for 5000 series and up

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-07 16:39:35 -04:00
Wey-Yi Guy 4e30cb691b iwlwifi: use S_IRUGO and S_IWUSR in module parameters
Instead of hardcode module parameter's permissions, use pre-defined.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-07 16:39:34 -04:00
Wey-Yi Guy f2d0d0e2ba iwlwifi: Adjust blink rate to compensate Clock difference
Adjust led blink rate to compensate on a MAC Clock difference on every
HW. Led blink rate analysis showed an average deviation of 0% on 3945,
5% on 4965 HW and 20% on 5000 series and up.
Need to compensate on the led on/off time per HW according to the
deviation to achieve the desired led frequency
The calculation is: (100-averageDeviation)/100 * blinkTime
For code efficiency the calculation will be:
    compensation = (100 - averageDeviation) * 64 / 100
    NewBlinkTime = (compensation * BlinkTime) / 64

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-07 16:39:32 -04:00
Wey-Yi Guy f3a2a42470 iwlwifi: separate set_hw_params function for 6000 series
Separate set_hw_params() function for 6000
series from 5000/1000 series because:
    1) 6000 series use different set of sensitivity range table
    2) 6000 series has different uCode image size

Also include the new sensitivity parameters needed by sensitivity
algorithm.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-07 16:39:32 -04:00
Wey-Yi Guy 9371d4ed79 iwlwifi: separate nic_config for different NIC
Different NIC has different requirements for configuration. Currently all
5000 series hardware and later share the same configuration function even
though they do not need the same configurations. Fix this by separating the
needed configuration actions for each hardware model.

.5000 series: L1-ASPM H/W bug work-around
              configure radio
              write CSR_HW_IF_CONFIG_REG for uCode use
              work-around for NIC get stuck after early PCIe power off

.1000 series: write CSR_HW_IF_CONFIG_REG for uCode use
              setting digital SVR for 1000 card to 1.32V

.6000 series: configure radio
              write CSR_HW_IF_CONFIG_REG for uCode use
              write CSR_GP_DRIVER_REG to indicate radio sku

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-07 16:39:31 -04:00
Reinette Chatre b7a794048f iwlwifi: fix 3945 ucode info retrieval after failure
When hardware or uCode problem occurs driver captures significant
information from device to enable debugging. The format of this information
is different between 3945 and 4965 and later devices, yet currently the
3945 uses the 4965 and later format. Fix this by adding a new library call
that is initialized to the correct formatting routine based on device.

This moves the iwlagn event and error log handling back to iwl-agn.c to
make it part of iwlagn module.

Also remove the 3945 sysfs file that triggers dump of event log - there is
already a debugfs file that can do it for all drivers.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-09-28 16:55:05 -04:00
Stanislaw Gruszka 6c6a22e268 iwlagn: fix panic in iwl{5000,4965}_rx_reply_tx
In some cases firmware can give us bad value of index in transmit
buffers array. This patch add sanity check for such values and return
from processing function instantly when it happens.

https://bugzilla.redhat.com/show_bug.cgi?id=521931

Patch was tested by reporter on iwl5000. I think check can be also
helpful for 4965.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-09-23 11:35:54 -04:00
Daniel C Halperin 396887a2b2 iwlwifi: fix erroneous use of iwl_rx_packet.len as a length
The field called 'len' in struct iwl_rx_packet is in fact not just a length
field but also includes some flags from the flow handler.  In several places
throughout the driver, this causes incorrect values to be interpreted as
lengths when the field is improperly masked.

In most situations the improper use is for debugging output, and simply results
in an erroneous message, such as:

[551933.070224] ieee80211 phy0: I iwl_rx_statistics Statistics notification received (480 vs -1367342620).

which should read '(480 vs 484)'.

In at least one case this could case bad things to happen:

void iwl_rx_pm_debug_statistics_notif(struct iwl_priv *priv,
                                      struct iwl_rx_mem_buffer *rxb)
{
        struct iwl_rx_packet *pkt = (struct iwl_rx_packet *)rxb->skb->data;
        IWL_DEBUG_RADIO(priv, "Dumping %d bytes of unhandled "
                        "notification for %s:\n",
                        le32_to_cpu(pkt->len), get_cmd_string(pkt->hdr.cmd));
        iwl_print_hex_dump(priv, IWL_DL_RADIO, pkt->u.raw, le32_to_cpu(pkt->len)
);
}
EXPORT_SYMBOL(iwl_rx_pm_debug_statistics_notif);

Given the rampant misuse of this field without proper masking throughout the
driver (every use but one), this patch renames the field from 'len' to
'len_n_flags' to reduce confusion.  It also adds the proper masking when
this field is used as a length value.

Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-20 11:33:13 -04:00
Wey-Yi Guy 15993e08ac iwlwifi: add thermal throttling support to 5150
Adding legacy thermal throttling management support to 5150 NIC

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-20 11:33:13 -04:00
Daniel C Halperin b261793da5 iwlwifi: use station HT capabilities and BSS operating mode for Green-field
Green-field mode should be configured in the HT station table.  This patch uses
both the per-station GF support flag as well as the current BSS HT operation
mode (non-GF stations present flag).

Added the "ht_greenfield_support" field to struct iwl_cfg to replace the
device-specific check in rs_use_green().  That check has been moved to
iwlcore_init_ht_hw_capab().

Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-20 11:33:12 -04:00
Wey-Yi Guy 7aafef1c6e iwlwifi: name changed from "fat" to "ht40"
Rename "fat" to "ht40"
The term "fat channel" is deprecated in favor of "HT40"

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-14 09:13:46 -04:00
Wey-Yi Guy 65b7998a9b iwlwifi: Distinguish power amplifier for 6000 series
For 6x00 2x2 NIC, two types of Power Amplifier are available.
In order for uCode to apply correct tx power,
driver needs to program the CSR_GP_DRIVER_REG register and
let uCode know the type of PA.
If driver do not program CSR_GP_DRIVER_REG register (default to 0),
then it is uCode's decision for tx power

2x2 Hybrid card: use both internal and external PA
2x2 IPA(Internal Power Amplifier) card: internal PA only

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:22 -04:00
Wey-Yi Guy 39b73fb15e iwlwifi: Thermal Throttling Management - Part 1
Part 1 of Thermal Throttling Management -

Thermal Throttling feature is used to put NIC into low power state when
driver detect the Radio temperature reach pre-defined threshold

Two Thermal Throttling Management Methods; this patch introduce the
Legacy Thermal Management:
   IWL_TI_0: normal temperature, system power state
   IWL_TI_1: high temperature detect, low power state
   IWL_TI_2: higher temperature detected, lower power state
   IWL_TI_CT_KILL: critical temperature detected, lowest power state

Once get into CT_KILL state, uCode go into sleep, driver will stop all
the active queues, then move to IWL_TI_CT_KILL state; also set up 5
seconds timer to toggle CSR flag, uCode wake up upon CSR flag change,
then measure the temperature.
If temperature is above CT_KILL exit threshold, uCode go backto sleep;
if temperature is below CT_KILL exit threshold, uCode send Card State
Notification response with appropriate CT_KILL status flag, and uCode
remain awake, Driver receive Card State Notification Response and update
the card temperature to the CT_KILL exit threshold.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-27 15:24:20 -04:00
Wey-Yi Guy 672639de13 iwlwifi: critical temperature enter/exit condition
If advance thermal throttling is used the driver need to pass both
"enter" and "exit" temperature to uCode.

Using different critical temperature threshold for legacy and advance
thermal throttling management based on the type of thermal throttling
method is used except 1000.
For 1000, it use advance thermal throttling critical temperature
threshold, but with legacy thermal management implementation until ucode
has the necessary implementations in place.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-27 15:24:20 -04:00
Reinette Chatre a562a9dda7 iwlwifi: make debug level more user friendly
* Deprecate the "debug50" module parameter used to obtain
  5000 series and up debugging. Replace it with "debug" module
  parameter to match with original driver and be consistent
  between them. The "debug50" module parameter can still be used,
  except that the module parameter is not writable in keeping
  with its previous state. We currently just mark it as "deprecated"
  and do not have it in the feature-removal-schedule. Some more
  cleanup of module parameters needs to be done and can then be
  entered together.

* Only make "debug" module parameters visible if the driver
  is compiled with CONFIG_IWLWIFI_DEBUG. This will eliminate
  a lot of confusion where users think they have set debug flags
  but yet cannot see any debug output.

* Make module parameters writable. This eliminates the need for the
  "debug_level" sysfs file, which can now also be deprecated and
  added to feature-removal-schedule. This file is in significant
  use though with many iwlwifi documents and text referring users
  to it. We can thus not take its removal lightly and keep it around.

With iwlcore shared between iwlagn and iwl3945 we really do not need
debug module parameters for each but can instead have one debug
module parameter for the iwlcore module. The same issue is here as
with the sysfs file - a lot of iwlwifi documentation and text (like
bug reports) rely on iwlagn and iwl3945 having this module parameter,
so changing this to a module parameter of iwlcore will have significant
impact and we do not do this for that reason.

One consequence of this patch is that if a user is running a system
with both 3945 and later hardware then the setting of the one module
parameter will affect the value of the other. The likelihood of this
seems low - and even if this setup is present it does not seem like an
issue for both modules to run with the same debug level.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-24 15:05:25 -04:00
Jay Sternberg cc0f555d51 iwlwifi: Handle new firmware file with ucode build number in header
Adding new API version to account for change to ucode file format.  New
header includes the build number of the ucode.  This build number is the
SVN revision thus allowing for exact correlation to the code that
generated it.

The header adds the build number so that older ucode images can also be
enhanced to include the build in the future.

some cleanup in iwl_read_ucode needed to ensure old header not used and
reduce unnecessary references through pointer with the data is already
in heap variable.

Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-24 15:05:24 -04:00
Wey-Yi Guy 02c06e4abc iwlagn: modify digital SVR for 1000
On 1000, there are two Switching Voltage Regulators (SVR). The first one
apply digital voltage level (1.32V) for PCIe block and core. We need to
use this regulator to solve a stability issue related to noisy DC2DC
line in the silicon.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-24 15:05:23 -04:00
Wey-Yi Guy fe6efb4b42 iwlwifi: no need to refer to max_nrg_cck range value
max_nrg_cck value inside the sensitivity range structure is not needed
for sensitivity calibration.
Keep the parameter in sensitivity structure but set the value to "0" in case
needed in the future implementation.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10 14:57:50 -04:00
Wey-Yi Guy 9d67187dbd iwlwifi: modify sensitivity value for 5150
In 5150 there is a long delay between the AGC(Automatic Gain Control) command
till the RF is stabilized causing us to miss detections when there was
adjacent channel noise, so we need to adjusted the Sensitivity calibration
for 5150 differently.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10 14:57:50 -04:00
Tomas Winkler c587de0b8d iwlwifi: unify station management
This patch unifies 3945 and AGN station management
It also removes useless struct iwl_station_mgmt ops
and cleanups a bit the interface

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-06-04 10:56:20 -04:00
David S. Miller c649c0e31d Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/wireless/ath/ath5k/phy.c
	drivers/net/wireless/iwlwifi/iwl-agn.c
	drivers/net/wireless/iwlwifi/iwl3945-base.c
2009-05-25 01:42:21 -07:00
Mohamed Abbas ef850d7cb3 iwlcore: support ICT interrupt
Add ICT interrupt handler support, ICT should improve CPU utilization
 since it does not require target read which is very expensive. This
 interrupt handler only added to 5000 cards and newer. Device will write
 interrupts to ICT shared table to inform driver about its interrupts.

These patches will not touch 3945 and 4965 interrupt handlers and tasklet.

Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-22 14:06:05 -04:00
Mohamed Abbas a8b50a0a96 iwlcore: register locks
Add new lock to be used when accessing some registers. Also move
    the register lock and iwl_grab_nic_access inside the function for register access. This
    will prevent from forgetting to hold locks and nic access in the right way and make code
    easier to maintain.

    We over use the priv->lock spin lock and I guess we need to add new
    one for Tx queue after that we might need to change most of these lock to
    BH and just keep priv->lock as irq type.

Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-22 14:06:04 -04:00
Wey-Yi Guy 62161aefa4 iwlwifi: Temperature sensor voltage reading for 5150
The temperature measurement by uCode for 5150 and 5000 are different
        CSR_HW_REV_TYPE_5150: temperature sensor output voltage
        CSR_HW_REV_TYPE_5000: temperature in Celsius
temperature related operation for 5150 is measured by temperature sensor
output voltage; additional conversion is required for set and store
the temperature.

To make sure support different HW design; implement _ops method for
temperature related functions (temperature reading and set ct kill
threshold)

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-22 14:06:03 -04:00
Jay Sternberg c9d2fbf36d iwlwifi: update 5000 ucode support to version 2 of API
enable iwl driver to support 5000 ucode having version 2 of API

Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-20 14:29:55 -04:00
Abhijeet Kolekar 09f9bf79b7 iwlwifi: remove radio disable parameter.
Patch removes the "manual radio disable" parameter
as there is no usage scenario of disabling radio using this module parameter.
User can use iwconfig's txpower to enable and disable radio.

This module parameter also does not work as expected. During module load
the status of radio is set, the radio is not actually disabled. Even so,
the moment mac80211 requests the interface to be up the radio will be
enabled again.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:57:19 -04:00
Abhijeet Kolekar 60690a6a38 iwlwifi: add config_ap lib op
add config_ap lib op to iwlwifi and iwl3945 in preparation
of future 3945 porting actions.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:43 -04:00
Abhijeet Kolekar 4582353166 iwlwifi: add set_rxon_chain op
add set_rxon_chain op to iwlwifi cfg ops in preparation of
future 3945 porting work.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:42 -04:00
Abhijeet Kolekar 06fd3d86a4 iwl3945/iwlwifi: unify add_station function
Patch unifies the add_station function for 3945 and iwlwifi drivers.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:42 -04:00
Abhijeet Kolekar e11bc0286a iwlwifi: use station management ops
Patch replaces station management functions with ops declared.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:42 -04:00
Abhijeet Kolekar 79fa455a99 iwlwifi: add station management ops
This patch adds declarations for station management ops to iwlwifi drivers.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:42 -04:00
Abhijeet Kolekar e0158e6110 iwlwifi: add commit_rxon lib
Patch adds commit_rxon lib operation to iwlwifi and iwl3945 drivers.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:41 -04:00
Abhijeet Kolekar 5bbe233b9b iwl3945: use iwl_bss_info_changed
3945 can use iwl_bss_info_changed.
A new lib op is created for post_assoicate to distinguish between
3945 and iwlwifi's post_associate operations.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22 16:54:41 -04:00
Johannes Berg e4e72fb4de mac80211/iwlwifi: move virtual A-MDPU queue bookkeeping to iwlwifi
This patch removes all the virtual A-MPDU-queue bookkeeping from
mac80211. Curiously, iwlwifi already does its own bookkeeping, so
it doesn't require much changes except where it needs to handle
starting and stopping the queues in mac80211.

To handle the queue stop/wake properly, we rewrite the software
queue number for aggregation frames and internally to iwlwifi keep
track of the queues that map into the same AC queue, and only talk
to mac80211 about the AC queue. The implementation requires calling
two new functions, iwl_stop_queue and iwl_wake_queue instead of the
mac80211 counterparts.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Reinette Chattre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:23 -04:00
Wey-Yi Guy a2f1cbebdc iwlwifi: report error when detect failure during stop agg queue
This fix related to bug 1921 at
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1921

when detect error during stopping tx aggregation queue, report the error to
help identify the problem.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27 20:13:00 -04:00
Jay Sternberg 39e6d2256b iwlwifi: update 5150 API version to support new firmware
update API to support new numbering that is used for other newer devices.
5150 ucode has not been released yet, so the first released API will be v2.
For those who do have a v1 API the driver does have backward compatibility
support new value of REPLY_TX_POWER_DBM_CMD

Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05 14:39:35 -05:00
Tomas Winkler 3fdb68de22 iwlwifi: use pci registers defined in pci_regs.h
This patch replaces where possible usage of pci register
defined in the driver by ones defined in pci_regs.h

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-13 13:46:04 -05:00
Jay Sternberg e8c00dcb02 iwlwifi: define structures and functions externally for customization
defined the structures and functions as extern to alter behavior used by
5000 series for other products including 100 and 6000 series

Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09 15:03:42 -05:00
Jay Sternberg 76a2407a5b iwlwifi: correct API command overlap
Correct the API commands where same command id used for two different
commands. Update max api versions for affected devices.

TX_ANT_CONFIGURATION_CMD was already using id 0x98, so
REPLY_TX_POWER_DBM_CMD moved to 0x95

Older API interfaces may used original value so V1 defines provided.

Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09 15:03:42 -05:00
Jay Sternberg 050681b77d iwlwifi: parametrize configuration of the PLL for exclusion on 6000
added a config parameter to enable setting PLL_CFG.  older hardware has
this parameter set true.  the 6000 family does not support this setting,
so this parameter set false.

Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09 15:03:42 -05:00
Jay Sternberg c0bac76a22 iwlwifi: simplify parameter setting to allow support for 6000 series
by parametrizing the set hw function, in addition to allowing for
supporting the 6000 family significantly simplify the addition of new
hardware.

Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09 15:03:42 -05:00
Tomas Winkler e1623446bb iwlwifi: don't use implicit priv in IWL_DEBUG
Call IWL_DEBUG macro with explicit priv argument.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09 15:03:34 -05:00
Samuel Ortiz a8e74e2774 iwl3945: Use iwlcore TX queue management routines
By adding an additional hw_params (tfd_size) and a new iwl_lib ops (txq_init),
we can now use the iwlcore TX queue management routines.
We had to add a new hw_params because we need to allocate the right DMA buffer
for TFDs, and those have a different sizes depending if you're on 3945 or agn.

Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29 16:01:34 -05:00
Jay Sternberg cec2d3f38c iwlwifi: remove static from 5000 structures
remove static from config structures which will be used by new
hardware that is similar to 5000.  This way the new devices
can use them without the new structures having to be stored in the
already overloaded iwl-5000.c file.

Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29 16:01:02 -05:00
Samuel Ortiz 7aaa1d79e3 iwlwifi: Add TFD library operations
The TFD structures for 3945 and agn HWs are fundamentally different. We thus
need to define operations for attaching and freeing them. This will allow us
to share a fair amount of code (cmd and tx queue related) between both
drivers.

Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29 16:00:56 -05:00
Reinette Chatre 01f8162a85 iwlwifi: update copyright year to 2009
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29 16:00:15 -05:00
Winkler, Tomas 141c43a3e4 iwl3945: kill iwl3945_rx_queue_restock
This patch kills iwl3945_rx_queue_restock function on prise of new
hw_params.rx_wrt_ptr_reg which holds per NIC RX write pointer register.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29 16:00:11 -05:00
Winkler, Tomas 15b1687cb4 iwlwifi: replace IWL_ERROR with IWL_ERR
IWL_ERR doesn't use hidden priv pointer.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29 15:59:17 -05:00