CONFIG_DEBUG_PAGEALLOC is now supported by x86, powerpc, sparc64, and
s390. This patch implements it for the rest of the architectures by
filling the pages with poison byte patterns after free_pages() and
verifying the poison patterns before alloc_pages().
This generic one cannot detect invalid page accesses immediately but
invalid read access may cause invalid dereference by poisoned memory and
invalid write access can be detected after a long delay.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds extra parameter to AT32 at32_map_usart(), so as to reserve
RTS/CTS/CLK pins.
All boards under arch/avr32/boards have been updated (trivial change), but
not all have been tested.
Signed-off-by: Peter Ma <pma@mediamatech.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch adds RTC support for the Merisc boards.
Signed-off-by: Jonas Larsson <jonas.larsson@martinsson.se>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch will adjust the setup the DMA controller for the AC97
Controller in the at32ap700x machine code. This setup matches the new
ALSA driver for the AC97C.
The struct ac97c_platform_data has been moved into its own header file
located in the sound include path.
Tested on ATSTK1006 + ATSTK1000.
This patch will setup the AC97 controller properly for the adjusted
machine code. Both EVKLCD10x and Hammerhead board has been updated.
Tested on EVKLCD10x, and copied to Hammerhead board.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
[haavard.skinnemoen@atmel.com: fold with board code update]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch will adjust the setup the DMA controller for the Audio
Bistream DAC in the at32ap700x machine code. This setup matches the new
ALSA driver for the ABDAC.
Tested on ATSTK1006 + ATSTK1000.
This patch will setup the needed platform data for the Audio Bistream
DAC used by the Favr-32 board.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
[haavard.skinnemoen@atmel.com: fold board code update]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Merisc is the family name for a range of AVR32-based boards.
The boards are designed to be used in a man-machine interfacing
environment, utilizing a touch-based graphical user interface. They host
a vast range of I/O peripherals as well as a large SDRAM & Flash memory
bank.
For more information see: http://www.martinsson.se/merisc
Signed-off-by: Jonas Larsson <jonas.larsson@martinsson.se>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* 'irq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (32 commits)
x86: disable __do_IRQ support
sparseirq, powerpc/cell: fix unused variable warning in interrupt.c
genirq: deprecate obsolete typedefs and defines
genirq: deprecate __do_IRQ
genirq: add doc to struct irqaction
genirq: use kzalloc instead of explicit zero initialization
genirq: make irqreturn_t an enum
genirq: remove redundant if condition
genirq: remove unused hw_irq_controller typedef
irq: export remove_irq() and setup_irq() symbols
irq: match remove_irq() args with setup_irq()
irq: add remove_irq() for freeing of setup_irq() irqs
genirq: assert that irq handlers are indeed running in hardirq context
irq: name 'p' variables a bit better
irq: further clean up the free_irq() code flow
irq: refactor and clean up the free_irq() code flow
irq: clean up manage.c
irq: use GFP_KERNEL for action allocation in request_irq()
kernel/irq: fix sparse warning: make symbol static
irq: optimize init_kstat_irqs/init_copy_kstat_irqs
...
This patch will use gpio_is_valid() to check the vbus_pin I/O line.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch adjusts the timing parameters for the Kyocera LCD panels
connected on the EVKLCD10X addon boards.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The PB15 GPIO line is used to control the enable and disable signal for
the backlight regulator on EVKLCD10x boards. This patch hands the I/O
line over to the LCDC driver, which will control when to enable and
disable the backlight.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
[haavard.skinnemoen@atmel.com: reverted ac97c change]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch removes the special handling of MCI platform data for
EVKLCD10x boards. This is now possible since the pin mask for the LCD
controller is no longer reserving the I/O lines used for MCI card
detection and write protect.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch will set the pin mask to alternative 18 bits per pixel output
for EVKLCD10x boards.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch adds two defines for setting a pin mask for 18-bit LCD panels
connected to the LCD controller. One mask for primary output and one
mask for alternative output.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch corrects the 15-bit LCDC pin mask definitions to select the
five upper lines in each color byte from the LCDC data output. When
reducing the color depth the LCDC will start filling MSB and downwards.
Also only enable 5 bits per color as the define indicates.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The current definition of CALLER_ADDRx isn't suitable for all platforms.
E.g. for ARM __builtin_return_address(N) doesn't work for N > 0 and
AFAIK for powerpc there are no frame pointers needed to have a working
__builtin_return_address. This patch allows defining the CALLER_ADDRx
macros in <asm/ftrace.h> and let these take precedence.
Because now <asm/ftrace.h> is included unconditionally in
<linux/ftrace.h> all archs that don't already had this include get an
empty one for free.
Signed-off-by: Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Impact: cleaner and consistent bootmem wrapping
By setting CONFIG_HAVE_ARCH_BOOTMEM_NODE, archs can define
arch-specific wrappers for bootmem allocation. However, this is done
a bit strangely in that only the high level convenience macros can be
changed while lower level, but still exported, interface functions
can't be wrapped. This not only is messy but also leads to strange
situation where alloc_bootmem() does what the arch wants it to do but
the equivalent __alloc_bootmem() call doesn't although they should be
able to be used interchangeably.
This patch updates bootmem such that archs can override / wrap the
backend function - alloc_bootmem_core() instead of the highlevel
interface functions to allow simpler and consistent wrapping. Also,
HAVE_ARCH_BOOTMEM_NODE is renamed to HAVE_ARCH_BOOTMEM.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Johannes Weiner <hannes@saeurebad.de>
Add support for inverted rdy_busy pin for Atmel nand device controller
It will fix building error on NeoCore926 board.
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Gregory CLEMENT <gclement@adeneo.adetelgroup.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
User space can request hardware and/or software time stamping.
Reporting of the result(s) via a new control message is enabled
separately for each field in the message because some of the
fields may require additional computation and thus cause overhead.
User space can tell the different kinds of time stamps apart
and choose what suits its needs.
When a TX timestamp operation is requested, the TX skb will be cloned
and the clone will be time stamped (in hardware or software) and added
to the socket error queue of the skb, if the skb has a socket
associated with it.
The actual TX timestamp will reach userspace as a RX timestamp on the
cloned packet. If timestamping is requested and no timestamping is
done in the device driver (potentially this may use hardware
timestamping), it will be done in software after the device's
start_hard_xmit routine.
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To add a bit in the preempt_count to be set when in NMI context, we
found that some archs did not have enough bits to spare. This is
due to the hardirq_count being a mask that can hold NR_IRQS.
Some archs allow for over 16000 IRQs, and that would require a mask
of 14 bits. The sofitrq mask is 8 bits and the preempt disable mask
is also 8 bits. The PREEMP_ACTIVE bit is bit 30, and bit 31 would
make the preempt_count (which is type int) a negative number.
A negative preempt_count is a sign of failure.
Add them up 14+8+8+1+1 you get 32 bits. No room for the NMI bit.
But the hardirq_count is to track the number of nested IRQs, not
the number of total IRQs. This originally took the paranoid approach
of setting the max nesting to NR_IRQS. But when we have archs with
over 1000 IRQs, it is not practical to think they will ever all
nest on a single CPU. Not to mention that this would most definitely
cause a stack overflow.
This patch sets a max of 10 bits to be used for IRQ nesting.
I did a 'git grep HARDIRQ' to examine all users of HARDIRQ_BITS and
HARDIRQ_MASK, and found that making it a max of 10 would not hurt
anyone. I did find that the m68k expected it to be 8 bits, so
I allow for the archs to set the number to be less than 10.
I removed the setting of HARDIRQ_BITS from the archs that set it
to more than 10. This includes ALPHA, ia64 and avr32.
This will always allow room for the NMI bit, and if we need to allow
for NMI nesting, we have 4 bits to play with.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
fix the following 'make headers_check' warnings:
usr/include/asm-avr32/swab.h:7: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm-avr32/swab.h:22: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Now that all EEPROM drivers live in the same place, let's harmonize
their symbol names.
Also fix eeprom's dependencies, it definitely needs sysfs, and is no
longer experimental after many years in the kernel tree.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Use .subsection to place fixups closer to their jump targets. This
increases the maximum size of the kernel before we get link errors
significantly.
The problem here is that we don't have a "call"-ish pseudo-instruction
to use instead of rjmp...we could add one, but that means we'll have to
wait for a new toolchain release, wait until we're fairly sure most
people are using it, etc...
As an added bonus, it should decrease the RAM footprint slightly,
though it might pollute the icache a bit more.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Replace handcoded rcall instructions with the call pseudo-instruction.
For kernels too far over 1MB the rcall instruction can't reach and
linking will fail. We already call the final linker with --relax which
converts call pseudo-instructions to the right things anyway.
This fixes
arch/avr32/kernel/built-in.o: In function `syscall_exit_work':
(.ex.text+0x198): relocation truncated to fit: R_AVR32_22H_PCREL against symbol `schedule' defined in .sched.text section in kernel/built-in.o
arch/avr32/kernel/built-in.o: In function `fault_exit_work':
(.ex.text+0x3b6): relocation truncated to fit: R_AVR32_22H_PCREL against symbol `schedule' defined in .sched.text section in kernel/built-in.o
But I'm still left with
arch/avr32/kernel/built-in.o:(.fixup+0x2): relocation truncated to fit: R_AVR32_22H_PCREL against `.text'+45a
arch/avr32/kernel/built-in.o:(.fixup+0x8): relocation truncated to fit: R_AVR32_22H_PCREL against `.text'+8ea
arch/avr32/kernel/built-in.o:(.fixup+0xe): relocation truncated to fit: R_AVR32_22H_PCREL against `.text'+abe
arch/avr32/kernel/built-in.o:(.fixup+0x14): relocation truncated to fit: R_AVR32_22H_PCREL against `.text'+ac8
arch/avr32/kernel/built-in.o:(.fixup+0x1a): relocation truncated to fit: R_AVR32_22H_PCREL against `.text'+ad2
arch/avr32/kernel/built-in.o:(.fixup+0x20): relocation truncated to fit: R_AVR32_22H_PCREL against `.text'+adc
arch/avr32/kernel/built-in.o:(.fixup+0x26): relocation truncated to fit: R_AVR32_22H_PCREL against `.text'+ae6
arch/avr32/kernel/built-in.o:(.fixup+0x2c): relocation truncated to fit: R_AVR32_22H_PCREL against `.text'+af0
arch/avr32/kernel/built-in.o:(.fixup+0x32): additional relocation overflows omitted from the output
These are caused by a similar problem with 'rjmp' instructions.
Unfortunately, there's no easy fix for these at the moment since we
don't have a arbitrary-range 'jmp' instruction similar to 'call'.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Add swab.h to kbuild.asm and remove the individual entries from
each arch, mark as unifdef as some arches have some kernel-only
bits inside.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (22 commits)
ioat: fix self test for multi-channel case
dmaengine: bump initcall level to arch_initcall
dmaengine: advertise all channels on a device to dma_filter_fn
dmaengine: use idr for registering dma device numbers
dmaengine: add a release for dma class devices and dependent infrastructure
ioat: do not perform removal actions at shutdown
iop-adma: enable module removal
iop-adma: kill debug BUG_ON
iop-adma: let devm do its job, don't duplicate free
dmaengine: kill enum dma_state_client
dmaengine: remove 'bigref' infrastructure
dmaengine: kill struct dma_client and supporting infrastructure
dmaengine: replace dma_async_client_register with dmaengine_get
atmel-mci: convert to dma_request_channel and down-level dma_slave
dmatest: convert to dma_request_channel
dmaengine: introduce dma_request_channel and private channels
net_dma: convert to dma_find_channel
dmaengine: provide a common 'issue_pending_all' implementation
dmaengine: centralize channel allocation, introduce dma_find_channel
dmaengine: up-level reference counting to the module level
...
While looking at reducing the amount of architecture namespace pollution
in the generic kernel, I found that asm/irq.h is included in the vast
majority of compilations on ARM (around 650 files.)
Since asm/irq.h includes a sub-architecture include file on ARM, this
causes a negative impact on the ccache's ability to re-use the build
results from other sub-architectures, so we have a desire to reduce the
dependencies on asm/irq.h.
It turns out that a major cause of this is the needless include of
linux/hardirq.h into asm-generic/local.h. The patch below removes this
include, resulting in some 250 to 300 files (around half) of the kernel
then omitting asm/irq.h.
My test builds still succeed, provided two ARM files are fixed
(arch/arm/kernel/traps.c and arch/arm/mm/fault.c) - so there may be
negative impacts for this on other architectures.
Note that x86 does not include asm/irq.h nor linux/hardirq.h in its
asm/local.h, so this patch can be viewed as bringing the generic version
into line with the x86 version.
[kosaki.motohiro@jp.fujitsu.com: add #include <linux/irqflags.h> to acpi/processor_idle.c]
[adobriyan@gmail.com: fix sparc64]
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The atomic_t type cannot currently be used in some header files because it
would create an include loop with asm/atomic.h. Move the type definition
to linux/types.h to break the loop.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dma_request_channel provides an exclusive channel, so we no longer need to
pass slave data through dmaengine.
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In the defconfigs for ATNGW100 and ATSTK100[236] the DMA Test driver is
compiled as a module. This means systems built with *_defconfig +
CONFIG_MODULES=n are unusable as the 3 dma test channels monopolise the
CPU.
I 'spose Haavard uses this module a lot but IMO it isn't really
something needed on all eval boards by default.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
As noted by Akinobu Mita in patch b1fceac2b9,
alloc_bootmem and related functions never return NULL and always return a
zeroed region of memory. Thus a NULL test or memset after calls to these
functions is unnecessary.
This was fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression E;
statement S;
@@
E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\|alloc_bootmem_node\|alloc_bootmem_low_pages_node\|alloc_bootmem_pages_node\)(...)
... when != E
(
- BUG_ON (E == NULL);
|
- if (E == NULL) S
)
@@
expression E,E1;
@@
E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\|alloc_bootmem_node\|alloc_bootmem_low_pages_node\|alloc_bootmem_pages_node\)(...)
... when != E
- memset(E,0,E1);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
at32_add_device_mci() will refuse to add the mci device if the data
parameter is NULL. Fix up the favr-32 and hammerhead boards so that this
doesn't happen.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Alex Raimondi <mailinglist@miromico.ch>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Needed to use the atmel-mci driver in an architecture
independant maner.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The Hammerhead platform is built around a AVR32 32-bit microcontroller
from Atmel. It offers versatile peripherals, such as ethernet, usb
device, usb host etc.
The board also incooperates a power supply and is a Power over Ethernet
(PoE) Powered Device (PD).
Additonally, a Cyclone III FPGA from Altera is integrated on the board.
The FPGA is mapped into the 32-bit AVR memory bus. The FPGA offers two
DDR2 SDRAM interfaces, which will cover even the most exceptional need
of memory bandwidth. Together with the onboard video decoder the board
is ready for video processing.
This patch does include the basic support for the fpga device driver,
but not the device driver itself.
Signed-off-by: Alex Raimondi <mailinglist@miromico.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
at32_reserve_pin now takes an u32 bitmask rather than a single pin.
This allows to reserve multiple pins at once.
Remove (undocumented) SDCS (pin PE26) from reservation in board
setup code.
Signed-off-by: Alex Raimondi <raimondi@miromico.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch removes a call to the deprecated function
at32_add_system_devices().
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
(I did not compile or test it, please let me know, or help fixing
it, if something is wrong with the conversion)
This patch is part of a larger patch series which will remove
the "char bus_id[20]" name string from struct device. The device
name is managed in the kobject anyway, and without any size
limitation, and just needlessly copied into "struct device".
To set and read the device name dev_name(dev) and dev_set_name(dev)
must be used. If your code uses static kobjects, which it shouldn't
do, "const char *init_name" can be used to statically provide the
name the registered device should have. At registration time, the
init_name field is cleared, to enforce the use of dev_name(dev) to
access the device name at a later time.
We need to get rid of all occurrences of bus_id in the entire tree
to be able to enable the new interface. Please apply this patch,
and possibly convert any remaining remaining occurrences of bus_id.
We want to submit a patch to -next, which will remove bus_id from
"struct device", to find the remaining pieces to convert, and finally
switch over to the new api, which will remove the 20 bytes array
and does no longer have a size limitation.
Thanks,
Kay
From: Kay Sievers <kay.sievers@vrfy.org>
Subject: avr: struct device - replace bus_id with dev_name(), dev_set_name()
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* 'cpus4096-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (77 commits)
x86: setup_per_cpu_areas() cleanup
cpumask: fix compile error when CONFIG_NR_CPUS is not defined
cpumask: use alloc_cpumask_var_node where appropriate
cpumask: convert shared_cpu_map in acpi_processor* structs to cpumask_var_t
x86: use cpumask_var_t in acpi/boot.c
x86: cleanup some remaining usages of NR_CPUS where s/b nr_cpu_ids
sched: put back some stack hog changes that were undone in kernel/sched.c
x86: enable cpus display of kernel_max and offlined cpus
ia64: cpumask fix for is_affinity_mask_valid()
cpumask: convert RCU implementations, fix
xtensa: define __fls
mn10300: define __fls
m32r: define __fls
h8300: define __fls
frv: define __fls
cris: define __fls
cpumask: CONFIG_DISABLE_OBSOLETE_CPUMASK_FUNCTIONS
cpumask: zero extra bits in alloc_cpumask_var_node
cpumask: replace for_each_cpu_mask_nr with for_each_cpu in kernel/time/
cpumask: convert mm/
...
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
Like fls, but can't be handed 0 and returns the bit number.
(I broke this arch in linux-next by using __fls in generic code).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The favr-32 board code still refers to the old asm/arch header files
which were moved to mach/ some time ago.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Enable JFFS2 write buffer support so that the kernel can access a root
filesystem in NAND flash.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch will remove the section .note.gnu.build-id added in binutils
2.18 from the vmlinux.bin binary. Not removing this section results in a
huge multiple gigabyte binary and likewize large uImage.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Impact: change calling convention of existing clock_event APIs
struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.
Another single-patch change. For safety, we BUG_ON() in
clockevents_register_device() if it's not set.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
Make USART initialization conform to Section 24.6.1 in the AT32AP7000 manual,
i.e. "To prevent the TXD line from falling when the USART is disabled, the use
of an internal pull up is mandatory."
Signed-off-by: Anders Blomdell <anders.blomdell@control.lth.se>
[haavard.skinnemoen@atmel.com: enable pullup on RX as well]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Add essential system devices, including GPIO controllers, automatically
at core_initcall time. This ensures that the devices are there when the
PIO driver gets initialized at postcore_initcall, fixing a bug exposed
by commit d6634db8fe "avr32: Use
platform_driver_probe for pio platform driver".
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The loops_per_jiffy variable isn't updated when cpufreq changes the CPU
frequency. This could cause udelay() and friends to produce wrong
delays.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Bug was introduced with the new at32_select_periph function.
Signed-off-by: Alex Raimondi <mailinglist@miromico.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This merges branches irq/genirq, irq/sparseirq-v4, timers/hpet-percpu
and x86/uv.
The sparseirq branch is just preliminary groundwork: no sparse IRQs are
actually implemented by this tree anymore - just the new APIs are added
while keeping the old way intact as well (the new APIs map 1:1 to
irq_desc[]). The 'real' sparse IRQ support will then be a relatively
small patch ontop of this - with a v2.6.29 merge target.
* 'genirq-v28-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (178 commits)
genirq: improve include files
intr_remapping: fix typo
io_apic: make irq_mis_count available on 64-bit too
genirq: fix name space collisions of nr_irqs in arch/*
genirq: fix name space collision of nr_irqs in autoprobe.c
genirq: use iterators for irq_desc loops
proc: fixup irq iterator
genirq: add reverse iterator for irq_desc
x86: move ack_bad_irq() to irq.c
x86: unify show_interrupts() and proc helpers
x86: cleanup show_interrupts
genirq: cleanup the sparseirq modifications
genirq: remove artifacts from sparseirq removal
genirq: revert dynarray
genirq: remove irq_to_desc_alloc
genirq: remove sparse irq code
genirq: use inline function for irq_to_desc
genirq: consolidate nr_irqs and for_each_irq_desc()
x86: remove sparse irq from Kconfig
genirq: define nr_irqs for architectures with GENERIC_HARDIRQS=n
...
This patch implements a new freezer subsystem in the control groups
framework. It provides a way to stop and resume execution of all tasks in
a cgroup by writing in the cgroup filesystem.
The freezer subsystem in the container filesystem defines a file named
freezer.state. Writing "FROZEN" to the state file will freeze all tasks
in the cgroup. Subsequently writing "RUNNING" will unfreeze the tasks in
the cgroup. Reading will return the current state.
* Examples of usage :
# mkdir /containers/freezer
# mount -t cgroup -ofreezer freezer /containers
# mkdir /containers/0
# echo $some_pid > /containers/0/tasks
to get status of the freezer subsystem :
# cat /containers/0/freezer.state
RUNNING
to freeze all tasks in the container :
# echo FROZEN > /containers/0/freezer.state
# cat /containers/0/freezer.state
FREEZING
# cat /containers/0/freezer.state
FROZEN
to unfreeze all tasks in the container :
# echo RUNNING > /containers/0/freezer.state
# cat /containers/0/freezer.state
RUNNING
This is the basic mechanism which should do the right thing for user space
task in a simple scenario.
It's important to note that freezing can be incomplete. In that case we
return EBUSY. This means that some tasks in the cgroup are busy doing
something that prevents us from completely freezing the cgroup at this
time. After EBUSY, the cgroup will remain partially frozen -- reflected
by freezer.state reporting "FREEZING" when read. The state will remain
"FREEZING" until one of these things happens:
1) Userspace cancels the freezing operation by writing "RUNNING" to
the freezer.state file
2) Userspace retries the freezing operation by writing "FROZEN" to
the freezer.state file (writing "FREEZING" is not legal
and returns EIO)
3) The tasks that blocked the cgroup from entering the "FROZEN"
state disappear from the cgroup's set of tasks.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: export thaw_process]
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Tested-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch series introduces a cgroup subsystem that utilizes the swsusp
freezer to freeze a group of tasks. It's immediately useful for batch job
management scripts. It should also be useful in the future for
implementing container checkpoint/restart.
The freezer subsystem in the container filesystem defines a cgroup file
named freezer.state. Reading freezer.state will return the current state
of the cgroup. Writing "FROZEN" to the state file will freeze all tasks
in the cgroup. Subsequently writing "RUNNING" will unfreeze the tasks in
the cgroup.
* Examples of usage :
# mkdir /containers/freezer
# mount -t cgroup -ofreezer freezer /containers
# mkdir /containers/0
# echo $some_pid > /containers/0/tasks
to get status of the freezer subsystem :
# cat /containers/0/freezer.state
RUNNING
to freeze all tasks in the container :
# echo FROZEN > /containers/0/freezer.state
# cat /containers/0/freezer.state
FREEZING
# cat /containers/0/freezer.state
FROZEN
to unfreeze all tasks in the container :
# echo RUNNING > /containers/0/freezer.state
# cat /containers/0/freezer.state
RUNNING
This patch:
The first step in making the refrigerator() available to all
architectures, even for those without power management.
The purpose of such a change is to be able to use the refrigerator() in a
new control group subsystem which will implement a control group freezer.
[akpm@linux-foundation.org: fix sparc]
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Acked-by: Pavel Machek <pavel@suse.cz>
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@tuxonice.net>
Tested-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SET_PERSONALITY macro is always called with a second argument of 0.
Remove the ibcs argument and the various tests to set the PER_SVR4
personality.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
As policy->governor is already set to CPUFREQ_DEFAULT_GOVERNOR in the
(always built-in) cpufreq core, we do not need to set it in the drivers.
This fixes the sparc64 allmodconfig build failure.
Also, remove a totally useles setting of ->policy in cpufreq-pxa3xx.c.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Please consider the following patch which adds support for a new AVR32
based board.
The board is closely based on Atmel's NGW100 reference board, but has an
extra 8MByte FLASH and 128KByte FRAM.
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The MIMC200 board uses the SPD output pin from the Ethernet MACs for
other purposes.
One of these is as a board-reset, so I've had to #define off the SPD
output pin declaration.
This is probably not the best way of achieving this, but works in the
current framework.
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch adds support for the Favr-32 board made by EarthLCD.
This kit, which is also called ezLCD-101, has a 10.4" touch screen LCD panel,
16 MB 32-bit SDRAM, 8 MB parallel flash, Ethernet, audio out, USB device,
SD-card slot, USART and various other connectors for cennecting stuff to SPI,
I2C, GPIO, etc.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch lets the user enable support for EVKLCD100 and EVKLCD101
(refered to by EVKLCD10X). By enabling EVKLCD10X support the LCD
controller and AC97 controller platform devices are added.
The user can also choose between the EVKLCD100 (QVGA display) and the
EVKLCD101 (VGA display), this is added to automagically select the
correct panel timing and resolution parameters.
Enabling support for EVKLCD10X addon board will cripple the MCI platform
device a bit since they share two GPIO lines (detect and write-protect).
These two lines are disabled when EVKLCD10X is enabled.
The default configurations are based upon ATNGW100, but with added AC97C
and LCDC driver. Virtual terminal is also enabled by default for
EVKLCD10X boards.
Verified on hardware with a NGW100 + EVKLCD100/101.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The contents of the ATSTK1000 Kconfig file itself is completely
conditional, so including it conditionally makes no sense and only adds
clutter.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Fix a few instances of board code breakage introduced by the atmel-mci
platform interface changes.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
at32_select_periph() now takes an u32 bitmask rather than a single pin.
This allows to set multiple pins at once.
Signed-off-by: Alex Raimondi <mailinglist@miromico.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Include <linux/pm.h> to see the declaration of pm_power_off, and remove
unneeded NULL initializer.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This adds support for DMA transfers through the generic DMA engine
framework with the DMA slave extensions.
The driver has been tested using mmc-block and ext3fs on several SD,
SDHC and MMC+ cards. Reads and writes work fine, with read transfer
rates up to 7.5 MiB/s on fast cards with debugging disabled.
Unfortunately, the driver has been known to lock up from time to time
with DMA enabled, so DMA support is currently optional and marked
EXPERIMENTAL. However, I didn't see any problems while testing 13
different cards (MMC, SD and SDHC of different brands and sizes), so I
suspect the "Initialize BLKR before sending data transfer command" fix
that was posted earlier fixed this as well.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The Atmel MCI controller can drive multiple cards through separate sets
of pins, but only one at a time. This patch adds support for
multiplexing access to the controller so that multiple card slots can be
used as if they were hooked up to separate mmc controllers.
The atmel-mci driver registers each slot as a separate mmc_host. Both
access the same common controller state, but they also have some state
on their own for card detection/write protect handling, and separate
shadows of the MR and SDCR registers.
When one of the slots receives a request from the mmc core, the common
controller state is checked. If it's idle, the request is submitted
immediately. If not, the request is added to a queue. When a request is
done, the queue is checked and if there is a queued request, it is
submitted before the completion callback is called.
This patch also includes a few cleanups and fixes, including a locking
overhaul. I had to change the locking extensively in any case, so I
might as well try to get it right. The driver no longer takes any
irq-safe locks, which may or may not improve the overall system
performance.
This patch also adds a bit of documentation of the internal data
structures.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Alexey Dobriyan