This field is redundant, because it is simply last success divided by
last attempt count. Removing it from the rate stats struct saves about
1.2 KiB per HT station.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
They are only used for debugging purposes and take a very long time to
overflow. Visibly reduces the size of the per-sta rate control data.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Test short preamble support in minstrel_ht_update_caps instead of
looking at the per-packet flag. Makes the code more efficient.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Improves dcache footprint by ensuring that fewer cache lines need to be
touched.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This speeds up the function in case a station already exists by avoiding
calling an expensive kzalloc just to free it again after the next check.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This fixes obtaining the rate info via sta_set_sinfo
when the rx rate is invalid (for instance, on IBSS
interface that has received no frames from one of its
peers).
Also initialize rinfo->flags for legacy rates, to not
rely on the whole sinfo being initialized to zero.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These functions drifts TSF timers, not TBTT.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mesh_sync_offset_adjust_tbtt() implements Extensible synchronization
framework ([1] 13.13.2 Extensible synchronization framework). It shall
not operate the flag "TBTT Adjusting subfield" ([1] 8.4.2.100.8 Mesh
Capability), since it is used only for MBCA ([1] 13.13.4 Mesh beacon
collision avoidance, see 13.13.4.4.3 TBTT scanning and adjustment
procedures for detail). So this patch remove the flag operations.
[1] IEEE Std 802.11 2012
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
[remove adjusting_tbtt entirely, since it's now unused]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a buffer is duplicated during MESH packet forwarding,
this patch ensures that the new buffer has enough headroom.
Signed-off-by: Cedric Izoard <cedric.izoard@ceva-dsp.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Could be useful for debugging memory consumption issues,
and perhaps power-save as well.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, kernel sends NEW_PEER_CANDIDATE event to user land even if
the found peer does not have any room to accept other peer. This causes
continuous connection trials.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the ability for an AP (and associated VLANs) to perform
multicast-to-unicast conversion for ARP, IPv4 and IPv6 frames
(possibly within 802.1Q). If enabled, such frames are to be sent
to each station separately, with the DA replaced by their own
MAC address rather than the group address.
Note that this may break certain expectations of the receiver,
such as the ability to drop unicast IP packets received within
multicast L2 frames, or the ability to not send ICMP destination
unreachable messages for packets received in L2 multicast (which
is required, but the receiver can't tell the difference if this
new option is enabled.)
This also doesn't implement the 802.11 DMS (directed multicast
service).
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
[use true/false, rename label to the correct "multicast",
use __be16 for ethertype and network order for constants]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 4a733ef1be (mac80211: remove PM-QoS listener) removed all use
of 'beaconint_us' from ieee80211_recalc_ps() but left the variable
intact. Compiling with W=1 gives the following warning, fix it.
net/mac80211/mlme.c: In function ‘ieee80211_recalc_ps’:
net/mac80211/mlme.c:1481:7: warning: variable ‘beaconint_us’ set but not used [-Wunused-but-set-variable]
iee80211_tu_to_usec has no side-effects and is safe to remove.
Fixes: 4a733ef1be ("mac80211: remove PM-QoS listener")
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kirtika Ruchandani <kirtika@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit b1bce14a79 (mac80211: update opmode when adding new station)
refactored ieee80211_vht_handle_opmode into __ieee80211_vht_handle_opmode
and ieee80211_vht_handle_opmode leaving a set but unused variable
(sband) in the former. Compiling with W=1 gives the following warning,
fix it.
net/mac80211/vht.c: In function ‘__ieee80211_vht_handle_opmode’:
net/mac80211/vht.c:424:35: warning: variable ‘sband’ set but not used [-Wunused-but-set-variable]
Remove 'struct ieee80211_local* local' as well, it was only used to
set sband.
This is a harmless warning, and is only being fixed to reduce the
noise with W=1 in the kernel.
Fixes: b1bce14a79 ("mac80211: update opmode when adding new station")
Cc: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kirtika Ruchandani <kirtika@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 633e271326 (mac80211: split sched scan IEs) introduced the
len variable to keep track of the return value of
ieee80211_build_preq_ies() but did not use it. Compiling with W=1
gives the following warning, fix it.
net/mac80211/scan.c: In function ‘__ieee80211_request_sched_scan_start’:
net/mac80211/scan.c:1123:9: warning: variable ‘len’ set but not used [-Wunused-but-set-variable]
This is a harmless warning and is only being fixed to reduce the noise
with W=1 in the kernel.
Fixes: 633e271326 ("mac80211: split sched scan IEs")
Cc: David Spinadel <david.spinadel@intel.com>
Cc: Alexander Bondar <alexander.bondar@intel.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kirtika Ruchandani <kirtika@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 5bcae31d9 (mac80211: implement multi-vif in-place reservations)
introduced ieee80211_vif_use_reserved_switch() with a counter variable
'i' that is set but not used. Compiling with W=1 gives the following
warning, fix it.
net/mac80211/chan.c: In function ‘ieee80211_vif_use_reserved_switch’:
net/mac80211/chan.c:1273:6: warning: variable ‘i’ set but not used [-Wunused-but-set-variable]
This is a harmless warning, and is only being fixed to reduce the
noise obtained with W=1 in the kernel.
Fixes: 5bcae31d9 ("mac80211: implement multi-vif in-place reservations")
Cc: Michal Kazior <michal.kazior@tieto.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kirtika Ruchandani <kirtika@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 3b17fbf87d introduced sta_get_expected_throughput()
leaving variable 'struct rate_control_ref* ref' set but unused.
Compiling with W=1 gives the following warning, fix it.
net/mac80211/sta_info.c: In function ‘sta_set_sinfo’:
net/mac80211/sta_info.c:2052:27: warning: variable ‘ref’ set but not used [-Wunused-but-set-variable]
Fixes: 3b17fbf87d ("mac80211: mesh: Add support for HW RC implementation")
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Maxim Altshul <maxim.altshul@ti.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit f027c2aca0 introduced 'rates_idx' in
ieee80211_tx_status_noskb but did not use it. Compiling with W=1
gives the following warning, fix it.
mac80211/status.c: In function ‘ieee80211_tx_status_noskb’:
mac80211/status.c:636:6: warning: variable ‘rates_idx’ set but not used [-Wunused-but-set-variable]
This is a harmless warning, and is only being fixed to reduce the
noise generated with W=1.
Fixes: f027c2aca0 ("mac80211: add ieee80211_tx_status_noskb")
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 554891e63a introduced 'struct ieee80211_rx_status' in
ieee80211_rx_h_defragment but did not use it. Compiling with W=1
gives the following warning, fix it.
net/mac80211/rx.c: In function ‘ieee80211_rx_h_defragment’:
net/mac80211/rx.c:1911:30: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
Fixes: 554891e63a ("mac80211: move packet flags into packet")
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since drivers know nothing about AP_VLAN interfaces, trying to
call drv_set_default_unicast_key() just results in a warning
and no call to the driver. Avoid the warning by not calling the
driver for this on AP_VLAN interfaces.
This means that drivers that somehow need this call for AP mode
will fail to work properly in the presence of VLAN interfaces,
but the current drivers don't seem to use it, and mac80211 will
select and indicate the key - so drivers should be OK now.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* fix a logic bug introduced by a previous cleanup
* fix nl80211 attribute confusing (trying to use
a single attribute for two purposes)
* fix a long-standing BSS leak that happens when an
association attempt is abandoned
-----BEGIN PGP SIGNATURE-----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=HvKt
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-12-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Three fixes:
* fix a logic bug introduced by a previous cleanup
* fix nl80211 attribute confusing (trying to use
a single attribute for two purposes)
* fix a long-standing BSS leak that happens when an
association attempt is abandoned
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When mac80211 abandons an association attempt, it may free
all the data structures, but inform cfg80211 and userspace
about it only by sending the deauth frame it received, in
which case cfg80211 has no link to the BSS struct that was
used and will not cfg80211_unhold_bss() it.
Fix this by providing a way to inform cfg80211 of this with
the BSS entry passed, so that it can clean up properly, and
use this ability in the appropriate places in mac80211.
This isn't ideal: some code is more or less duplicated and
tracing is missing. However, it's a fairly small change and
it's thus easier to backport - cleanups can come later.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
A-MSDU aggregation alters the QoS header after a frame has been
enqueued, so it needs to be ready before enqueue and not overwritten
again afterwards
Fixes: bb42f2d13f ("mac80211: Move reorder-sensitive TX handlers to after TXQ dequeue")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The call to ieee80211_txq_enqueue overwrites the vif pointer with the
codel enqueue time, so setting it just before that call makes no sense.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The sequence number counter is used to derive the starting sequence
number. Since that counter is updated on tx dequeue, the A-MPDU flag
needs to be up to date at the tme of dequeue as well.
This patch prevents sending more A-MPDU frames after the session has
been terminated and also ensures that aggregation starts right after the
session has been established
Fixes: bb42f2d13f ("mac80211: Move reorder-sensitive TX handlers to after TXQ dequeue")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit c68df2e7be.
__sta_info_recalc_tim turns into a no-op if local->ops->set_tim is not
set. This prevents the beacon TIM bit from being set for all drivers
that do not implement this op (almost all of them), thus thoroughly
essential AP mode powersave functionality.
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: c68df2e7be ("mac80211: allow using AP_LINK_PS with mac80211-generated TIM IE")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is a workaround for VHT-enabled STAs which break the spec
and have the VHT-MCS Rx map filled in with value 3 for all eight
spacial streams, an example is AR9462 in AP mode.
As per spec, in section 22.1.1 Introduction to the VHT PHY
A VHT STA shall support at least single spactial stream VHT-MCSs
0 to 7 (transmit and receive) in all supported channel widths.
Some devices in STA mode will get firmware assert when trying to
associate, examples are QCA9377 & QCA6174.
Packet example of broken VHT Cap IE of AR9462:
Tag: VHT Capabilities (IEEE Std 802.11ac/D3.1)
Tag Number: VHT Capabilities (IEEE Std 802.11ac/D3.1) (191)
Tag length: 12
VHT Capabilities Info: 0x00000000
VHT Supported MCS Set
Rx MCS Map: 0xffff
.... .... .... ..11 = Rx 1 SS: Not Supported (0x0003)
.... .... .... 11.. = Rx 2 SS: Not Supported (0x0003)
.... .... ..11 .... = Rx 3 SS: Not Supported (0x0003)
.... .... 11.. .... = Rx 4 SS: Not Supported (0x0003)
.... ..11 .... .... = Rx 5 SS: Not Supported (0x0003)
.... 11.. .... .... = Rx 6 SS: Not Supported (0x0003)
..11 .... .... .... = Rx 7 SS: Not Supported (0x0003)
11.. .... .... .... = Rx 8 SS: Not Supported (0x0003)
...0 0000 0000 0000 = Rx Highest Long GI Data Rate (in Mb/s, 0 = subfield not in use): 0x0000
Tx MCS Map: 0xffff
...0 0000 0000 0000 = Tx Highest Long GI Data Rate (in Mb/s, 0 = subfield not in use): 0x0000
Signed-off-by: Filip Matusiak <filip.matusiak@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
* client FILS authentication support in mac80211 (Jouni)
* AP/VLAN multicast improvements (Michael Braun)
* config/advertising support for differing beacon intervals on
multiple virtual interfaces (Purushottam Kushwaha, myself)
* deprecate the old WDS mode for cfg80211-based drivers, the
mode is hardly usable since it doesn't support any "modern"
features like WPA encryption (2003), HT (2009) or VHT (2014),
I'm not even sure WEP (introduced in 1997) could be done.
-----BEGIN PGP SIGNATURE-----
iQIcBAABCgAGBQJYEy/9AAoJEGt7eEactAAd/V0P/0FmHGS8HjlSjm+1p6sbWKbt
5v8bb3cuKHQiYiUM6euIXql2OYuOEHVAQEpNoPXN9CsfKFYgbIH6yW6d8HtKNedV
n9lmMy/U6yJX9nYt7yMIQ3kLkbEg+YU58B9Hf47waWXLLSNVumS8rfNBn43EoNQf
VKWYPWpetsCRIWJ1fnLuxvMHCtOOYCxH+491BUonof32+DKPEAsAbnszZ2ElufTR
7KNyA3K6leOtTd5Ml52dvLOGNc+h2C83VAMxiShq/6r8OnlX5tPifaubzd9n3m41
jiJJH/92ESrtF2AaWEm8slcgtcfHS/O7y/FSoV4r0PMSvPTBdjwQ9nqCsbONd831
vjj6c6YWNxgHPcISX0XcWz+FHnLJdUGaDUtHjAJYw4oH4gaRXwfSw0U+jvdlSMUf
2CBUArk5f0OEguzwa/5X4Jio3OPPIj4jY/lKplcpLOUu8K2FWTLDuIlww/FHXovs
rDzTLQeXZkx+MkszkTJN42qSEfOFly91J6OA2Wju+emBqrLIbkAGmvyLVg8U8BQd
gG7oltgmZ6Xg6fEnUQqpIDO7UJlQ+GXAU04SpNDMv1j/ueUJskxlr3hYM7E9ueQv
LJcZcVV0RAwNRw52cEsdcYCMLuSMYRrO1OHlkl0wd+x2hFrUCWnVzUgLEUhNBV+c
ICmNMr96nKhrZI217yzF
=SjfQ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-10-28' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Among various cleanups and improvements, we have the following:
* client FILS authentication support in mac80211 (Jouni)
* AP/VLAN multicast improvements (Michael Braun)
* config/advertising support for differing beacon intervals on
multiple virtual interfaces (Purushottam Kushwaha, myself)
* deprecate the old WDS mode for cfg80211-based drivers, the
mode is hardly usable since it doesn't support any "modern"
features like WPA encryption (2003), HT (2009) or VHT (2014),
I'm not even sure WEP (introduced in 1997) could be done.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc -Wmaybe-uninitialized reports a bug in aes_siv_encryp:
net/mac80211/fils_aead.c: In function ‘aes_siv_encrypt.constprop’:
net/mac80211/fils_aead.c:84:26: error: ‘tfm2’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
At the time that the memory allocation fails, 'tfm2' has not been
allocated, so we should not attempt to free it later, and we can
simply return an error.
Fixes: 39404feee6 ("mac80211: FILS AEAD protection for station mode association frames")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With the previous commits, initial FILS authentication/association
support is now functional in mac80211-based drivers for station role
(and FILS AP case is covered by user space in hostapd withotu requiring
mac80211 changes).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds support for encrypting (Re)Association Request frame and
decryption (Re)Association Response frame when using FILS in station
mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The special SAE case should be limited only for SAE since the more
generic AUTH_DATA can now be used with other authentication algorithms
as well.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds defines and nl80211 extensions to allow FILS Authentication to
be implemented similarly to SAE. FILS does not need the special rules
for the Authentication transaction number and Status code fields, but it
does need to add non-IE fields. The previously used
NL80211_ATTR_SAE_DATA can be reused for this to avoid having to
duplicate that implementation. Rename that attribute to more generic
NL80211_ATTR_AUTH_DATA (with backwards compatibility define for
NL80211_SAE_DATA).
Also document the special rules related to the Authentication
transaction number and Status code fiels.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As part of interface combination checking, verify any new
interface's beacon intervals. In fact, just always add the
beacon interval since that's harmless.
With this patch, mac80211 is prepared for drivers that set
the min_beacon_int_gcd parameter in interface combinations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- set max_mtu in wil6210 driver
- set max_mtu in atmel driver
- set min/max_mtu in cisco airo driver, remove airo_change_mtu
- set min/max_mtu in ipw2100/ipw2200 drivers, remove libipw_change_mtu
- set min/max_mtu in p80211netdev, remove wlan_change_mtu
- set min/max_mtu in net/mac80211/iface.c and remove ieee80211_change_mtu
- set min/max_mtu in wimax/i2400m and remove i2400m_change_mtu
- set min/max_mtu in intersil/hostap and remove prism2_change_mtu
- set min/max_mtu in intersil/orinoco
- set min/max_mtu in tty/n_gsm and remove gsm_change_mtu
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: Maya Erez <qca_merez@qca.qualcomm.com>
CC: Simon Kelley <simon@thekelleys.org.uk>
CC: Stanislav Yakovlev <stas.yakovlev@gmail.com>
CC: Johannes Berg <johannes@sipsolutions.net>
CC: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The uapsd_queue field is in QoS IE order and not in
IEEE80211_AC_*'s order.
This means that mac80211 would get confused between
BK and BE which is certainly not such a big deal but
needs to be fixed.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently mac80211 determines whether HW does fragmentation
by checking whether the set_frag_threshold callback is set
or not.
However, some drivers may want to set the HW fragmentation
capability depending on HW generation.
Allow this by checking a HW flag instead of checking the
callback.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
[added the flag to ath10k and wlcore]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwlwifi will check internally that the tid maps to an AC
that is trigger enabled, but can't know what tid exactly.
Allow the driver to pass a generic tid and make mac80211
assume that a trigger frame was received.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver sets the SUPPORTS_REORDERING_BUFFER hardware flag,
the debugfs data for RX aggregation sessions won't even indicate
that a session is open. Since the previous fix to store the dialog
token separately, we can indicate that it's open and add the token
so that there's at least some data (ssn is not available.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On drivers setting the SUPPORTS_REORDERING_BUFFER hardware flag,
we crash when the peer sends an AddBA request while we already
have a session open on the seame TID; this is because on those
drivers, the tid_agg_rx is left NULL even though the session is
valid, and the agg_session_valid bit is set.
To fix this, store the dialog tokens outside the tid_agg_rx to
be able to compare them to the received AddBA request.
Fixes: f89e07d4cf ("mac80211: agg-rx: refuse ADDBA Request with timeout update")
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some crypto implementations (such as the generic CCM wrapper in crypto/)
use scatterlists to map fields of private data in their struct aead_req.
This means these data structures cannot live in the vmalloc area, which
means that they cannot live on the stack (with CONFIG_VMAP_STACK.)
This currently occurs only with the generic software implementation, but
the private data and usage is implementation specific, so move the whole
data structures off the stack into heap by allocating every time we need
to use them.
In addition, take care not to put any of our own stack allocations into
scatterlists. This involves reserving some extra room when allocating the
aead_request structures, and referring to those allocations in the scatter-
lists (while copying the data from the stack before the crypto operation)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
According to IEEE 802.11-2012 section 8.3.2 table 8-19, the outer SA/DA
of A-MSDU frames need to be changed depending on FromDS/ToDS values.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
[use ether_addr_copy and add alignment annotations]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the growing parameter list to a structure for the interface
combination check and iteration functions in cfg80211 and mac80211
to make the code easier to understand.
Signed-off-by: Purushottam Kushwaha <pkushwah@qti.qualcomm.com>
[edit commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michael Braun reported that when trying to inject A-MSDUs over
monitor interfaces, the frame doesn't come out right since the
QoS header A-MSDU bit is overwritten.
Rather than adding that bit specifically simply preserve those
bits that we don't set here, since we typically get here with
a zeroed-out QoS header anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds filtering for multicast data packets on AP_VLAN
interfaces that have no authorized station connected and changes
filtering on AP interfaces to not count stations assigned to
AP_VLAN interfaces.
This saves airtime and avoids waking up other stations currently
authorized in this BSS. When using WPA, the packets dropped could
not be decrypted by any station.
The behaviour when there are no AP_VLAN interfaces is left unchanged.
When there are AP_VLAN interfaces, this patch
1. adds filtering multicast data packets sent on AP_VLAN interfaces
that have no authorized station connected.
No filtering happens on 4addr AP_VLAN interfaces.
2. makes filtering of multicast data packets sent on AP interfaces
depend on the number of authorized stations in this bss not
assigned to an AP_VLAN interface.
Therefore, a new num_mcast_sta counter is added for AP_VLAN interfaces.
The existing one for AP interfaces is altered to not track stations
assigned to an AP_VLAN interface.
The new counter is exposed in debugfs.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
[reformat commit message a bit, unline ieee80211_vif_{inc,dec}_num_mcast]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Checking for num_mcast_sta in __ieee80211_request_smps_ap() is
unnecessary as sta list will be empty in this case anyway, so
the list iteration will just exit immediately. Since this isn't
a "hot" code path, it doesn't really matter, and the next patch
will redefine num_mcast_sta to make this check invalid.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
[change commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
sta_info_get_bss() is equivalent to sta_info_get() in the
mesh case, since sta->sdata->bss will be NULL (it's only
set for AP/AP_VLAN interfaces.) Thus, the mesh check here
isn't actually needed - remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using IEEE 802.11r FT OVER-DS roaming with AP_VLAN, hostapd needs to
send out a frame using CMD_FRAME for a station assigned to an AP_VLAN
interface.
Right now, the userspace needs to give the exact AP_VLAN interface index
for CMD_FRAME; hostapd does not do this. Additionally, userspace cannot
use GET_STATION to query the AP_VLAN ifidx, as while GET_STATION finds
stations assigned to AP_VLAN even if the AP iface is queried, it does not
return AP_VLAN ifidx (it returns the queried one).
This breaks IEEE 802.11r over_ds with vlans, as the reply frame does not
get out. This patch fixes this by using get_sta_bss for CMD_FRAME.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As pointed out by Michael Braun, we don't check inner L2 addresses
during A-MSDU decapsulation, leading to the possibility that, for
example, a station associated to an AP sends frames as though they
came from somewhere else.
Fix this problem by letting cfg80211 validate the addresses, as
indicated by passing in the ones that need to be validated.
Reported-by: Michael Braun <michael-dev@fami-braun.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We should not accept arbitrary DA/SA inside A-MSDUs, it could be used
to circumvent protections, like allowing a station to send frames and
make them seem to come from somewhere else.
Add the necessary infrastructure in cfg80211 to allow such checks, in
further patches we'll start using them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's only a single case where has_80211_header is passed as true,
which is in mac80211. Given that there's only simple code that needs
to be done before calling it, export that function from cfg80211
instead and let mac80211 call it itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In mac80211, multicast A-MSDUs are accepted in many cases that
they shouldn't be accepted in:
* drop A-MSDUs with a multicast A1 (RA), as required by the
spec in 9.11 (802.11-2012 version)
* drop A-MSDUs with a 4-addr header, since the fourth address
can't actually be useful for them; unless 4-address frame
format is actually requested, even though the fourth address
is still not useful in this case, but ignored
Accepting the first case, in particular, is very problematic
since it allows anyone else with possession of a GTK to send
unicast frames encapsulated in a multicast A-MSDU, even when
the AP has client isolation enabled.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Resolve the merge conflict between Felix's/my and Toke's patches
coming into the tree through net and mac80211-next respectively.
Most of Felix's changes go away due to Toke's new infrastructure
work, my patch changes to "goto begin" (the label wasn't there
before) instead of returning NULL so flow control towards drivers
is preserved better.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TXQ intermediate queues can cause packet reordering when more than
one flow is active to a single station. Since some of the wifi-specific
packet handling (notably sequence number and encryption handling) is
sensitive to re-ordering, things break if they are applied before the
TXQ.
This splits up the TX handlers and fast_xmit logic into two parts: An
early part and a late part. The former is applied before TXQ enqueue,
and the latter after dequeue. The non-TXQ path just applies both parts
at once.
Because fragments shouldn't be split up or reordered, the fragmentation
handler is run after dequeue. Any fragments are then kept in the TXQ and
on subsequent dequeues they take precedence over dequeueing from the FQ
structure.
This approach avoids having to scatter special cases all over the place
for when TXQ is enabled, at the cost of making the fast_xmit and TX
handler code slightly more complex.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
[fix a few code-style nits, make ieee80211_xmit_fast_finish void,
remove a useless txq->sta check]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The old value was 30ms, which means mesh sync will treat
any value below as merely TSF drift. This isn't really
reasonable (typical drift is < 10us/s) since people
probably want to adjust TSF in smaller increments (for ie.
beacon collision avoidance) without mesh sync fighting
back.
Change max drift adjustment to 0.8ms, so manual TSF
adjustments can be made in 1ms increments, with some
margin.
Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows the mesh sync (and debugfs) code to make incremental
TSF adjustments, avoiding any uncertainty introduced by delay in
programming absolute TSF.
Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Small devices can run out of memory from queueing too many packets. If
VHT is not supported by the PHY, having more than 4 MBytes of total
queue in the TXQ intermediate queues is not needed, and so we can safely
limit the memory usage in these cases and avoid OOM.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Provide an API to report NAN function match. Mac80211 will lookup the
corresponding cookie and report the match to cfg80211.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement add/rm_nan_func functions and handle NAN function
termination notifications. Handle instance_id allocation for
NAN functions and implement the reconfig flow.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement nan_change_conf callback which allows to change current
NAN configuration (master preference and dual band operation).
Store the current NAN configuration in sdata, so it can be used
both to provide the driver the updated configuration with changes
and also it will be used in hw reconfig flows in next patches.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This code doesn't do much besides allowing to start and
stop the vif.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows user space to start/stop NAN interface.
A NAN interface is like P2P device in a few aspects: it
doesn't have a netdev associated to it.
Add the new interface type and prevent operations that
can't be executed on NAN interface like scan.
Define several attributes that may be configured by user space
when starting NAN functionality (master preference and dual
band operation)
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TXQ path restructure requires ieee80211_tx_dequeue() to call TX
handlers and parts of the xmit_fast path. Move the function to later in
tx.c in preparation for this.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 currently uses rhashtable with insecure_elasticity set
to true. The latter is because of duplicate objects. What's
more, mac80211 walks the rhashtable chains by hand which is broken
as rhashtable may contain multiple tables due to resizing or
rehashing.
This patch fixes it by converting it to the newly added rhltable
interface which is designed for use with duplicate objects.
With rhltable a lookup returns a list of objects instead of a
single one. This is then fed into the existing for_each_sta_info
macro.
This patch also deletes the sta_addr_hash function since rhashtable
defaults to jhash.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
* MU-MIMO sniffer support in mac80211
* a create_singlethread_workqueue() cleanup
* interface dump filtering that was documented but not implemented
* support for the new radiotap timestamp field
* send delBA in two unexpected conditions (as required by the spec)
* connect keys cleanups - allow only WEP with index 0-3
* per-station aggregation limit to work around broken APs
* debugfs improvement for the integrated codel algorithm
and various other small improvements and cleanups.
-----BEGIN PGP SIGNATURE-----
iQIcBAABCgAGBQJX2+umAAoJEGt7eEactAAdIMkP/jMmpbxkzD64L7nTkO4APGva
r6RmMM1SmgVD/CtVkjlBLuvo5YOTWv/vWvy6KoUESOINAx/e6T3T7bmmCOXzbsOL
e5/YYcS1AOqgn5SdhgIj1E5cpdYIhlUGRlNJ0qEjeLLrh4/TLUNbCcuPhOYybUMz
fUrdPKgDeWb7x9EHLENhPsVtCXWwKnkDIS4qclPZCWgRj46XM4pNB4OlvCUzGY6k
bOqGJfrtjYjgKFDmPFqfYA4JDA56980qqO41+eEKXeMvDKNs+pSiNco130Q+uU3E
o7tk9DMnAnCy2GihpV1ZYVkLr6O+7o9xVuenj3NRlhyd1mn2gXxLcO4AkHcrZBkf
Ei+2L+KgnWELyqiSOaGTJKlugsgS4DDoNnFEIVjSweQ9DIoBA/Gj/6+4uZeHXJ3M
bEjtHnCLi5CuI067uBoevwXFoMi1poWra2KnZKOZzFS5OL3xHv4//x/Wmnn2/5Jz
ffEwVyRmTY76sLWfnwXUDClrFWAYQrpNyTryc+k3cpYKzhnseiqt+z43cBuISm00
uh5B9PpPB8RhtUnXrL/SHRyf8YEluaidTsI2lc1LvwXOc0+Zbp73mTCgP+rzLs9p
K2qVRiozpIXanW6hKmmaDwjKlcAKKLP0xN2v90MqwQt4YdLIKlXnll1AH2BawzuP
OWB3n8D0I6y0PWH+Yo8o
=s1MY
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-09-16' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have various things - all across the board:
* MU-MIMO sniffer support in mac80211
* a create_singlethread_workqueue() cleanup
* interface dump filtering that was documented but not implemented
* support for the new radiotap timestamp field
* send delBA in two unexpected conditions (as required by the spec)
* connect keys cleanups - allow only WEP with index 0-3
* per-station aggregation limit to work around broken APs
* debugfs improvement for the integrated codel algorithm
and various other small improvements and cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In 46fa38e84b ("mac80211: allow software PS-Poll/U-APSD with
AP_LINK_PS"), Johannes allowed to use mac80211's code for handling
stations that go to PS or send PS-Poll / uAPSD trigger frames for
devices that enable RSS.
This means that mac80211 doesn't look at frames anymore but rather
relies on a notification that will come from the device when a PS
transition occurs or when a PS-Poll / trigger frame is detected by
the device.
iwlwifi will need this capability but still needs mac80211 to take
care of the TIM IE. Today, if a driver sets AP_LINK_PS, mac80211
will not update the TIM IE. Change mac80211 to check existence of
the set_tim driver callback rather than using AP_LINK_PS to decide
if the driver handles the TIM IE internally or not.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[reword commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Based on consecutive msdu failures, mac80211 triggers CQM packet-loss
mechanism. Drivers like ath10k that have its own connection monitoring
algorithm, offloaded to firmware for triggering station kickout. In case
of station kickout, driver will report low ack status by mac80211 API
(ieee80211_report_low_ack).
This flag will enable the driver to completely rely on firmware events
for station kickout and bypass mac80211 packet loss mechanism.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
No drivers implement this, relying either on the recursive
directory removal to remove their debugfs, or not having any
to start with. Remove the dead driver callback.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If chanctx is derived as container_of() from a non-NULL pointer,
it can't ever be NULL. Since we checked conf before, that's true
here, so remove the useless NULL check.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The next line overwrites this assignment, so remove it; there's
no real value in using it for the next assignment either.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Passing the 'info' pointer where a 'info->aborted' is expected will
always lead to tracing to erroneously record that the scan was aborted,
fix that by passing the correct info->aborted. The remaining data will
be collected in cfg80211, so I haven't duplicated it here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the unlikely situation that the supplicant has negotiated
admission for the background AC (which it has no reason to as
it's not supposed to be requiring admission control to start
with, and we'd ignore such a requirement anyway), the loop
here may terminate with non_acm_ac == 4, which leads to an
array overrun.
Check this explicitly just for completeness.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since mac80211 doesn't currently support TSIDs 8-15 which can
only be used after QoS TSPEC negotiation (and not even after
WMM negotiation), reject attempts to set up aggregation
sessions for them, which might confuse drivers. In mac80211
we do correctly handle that, but the TSIDs should never get
used anyway, and drivers might not be able to handle it.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The A-MSDU TX code (within TXQs) didn't always check the return value
of skb_linearize() properly, resulting in potentially passing a frag-
list SKB down to the driver even when it said it can't handle it. Fix
that.
Fixes: 6e0456b545 ("mac80211: add A-MSDU tx support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
__ieee80211_suspend() checks early on if there's anything
to do by checking open_count, so there's no need to check
again later in the function. Remove the useless check.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
smatch pointed out that the second check of "tdls_auth" was
pointless since if it was true, we returned from the function
already. We can further simplify the code by moving the first
check (if it's a TDLS peer at all) into the outer if, to only
handle that inside. This simplifies the control flow here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the 'aqm' stats in mac80211 only keeps overlimit drop stats,
not CoDel stats. This moves the CoDel stats into the txqi structure to
keep them per txq in order to show them in debugfs.
In addition, the aqm debugfs output is restructured by splitting it up
into three files: One global per phy, one per netdev and one per
station, in the appropriate directories. The files are all called aqm,
and are only created if the driver supports the wake_tx_queue op (rather
than emitting an error on open as previously).
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
A fixed mpath was not quite being treated as such:
1) if a PERR frame was received, a fixed mpath was
deactivated.
2) queued path discovery for fixed mpath was potentially
being considered, changing mpath state.
3) other mpath flags were potentially being inherited when
fixing the mpath. Just assign PATH_FIXED and SN_VALID.
This solves several issues when fixing a mesh path in one
direction. The reverse direction mpath should probably
also be fixed, or root announcements at least be enabled.
Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using intermediate queues, sequence number allocation is deferred
until dequeue. This doesn't work for PS response frames, which bypass
those queues.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Handle the case where the mac80211 intermediate queues are empty and the
driver has buffered frames
Fixes: ba8c3d6f16 ("mac80211: add an intermediate software queue implementation")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we don't have a BA session, send delBA, as requested by the
IEEE 802.11 spec. Apply the same limit of sending such a delBA
only once as in the previous patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we receive data frames with ACK policy BlockAck, send
delBA as requested by the 802.11 spec. Since this would be
happening for every frame inside an A-MPDU if it's really
received outside a session, limit it to a single attempt.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the existing device timestamp from the RX status information
to add support for the new radiotap timestamp field. Currently
only 32-bit counters are supported, but we also add the radiotap
mactime where applicable. This new field allows more flexibility
in where the timestamp is taken etc. The non-timestamp data in
the field is taken from a new field in the hw struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
add support to MU-MIMO air sniffer according groupID:
in monitor mode, use a given MU-MIMO groupID to monitor stations
that belongs to that group using MU-MIMO.
add support for following a station according to its MAC address
using VHT MU-MIMO sniffer:
the monitors wait until they get an action MU-MIMO notification
frame, then parses it in order to find the groupID that corresponds
to the given MAC address and monitors packets destined to that
groupID using VHT MU-MIMO.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ability to change the max_rx_aggregation frames is useful
in cases of IOP.
There exist some devices (latest mobile phones and some AP's)
that tend to not respect a BA sessions maximum size (in Kbps).
These devices won't respect the AMPDU size that was negotiated during
association (even though they do respect the maximal number of packets).
This violation is characterized by a valid number of packets in
a single AMPDU. Even so, the total size will exceed the size negotiated
during association.
Eventually, this will cause some undefined behavior, which in turn
causes the hw to drop packets, causing the throughput to plummet.
This patch will make the subframe limitation to be held by each station,
instead of being held only by hw.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Insert the u32 monitor flags variable in a new structure
that represents a monitor interface.
This will allow to add more configuration variables to
that structure which will happen in an upcoming change.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stop downgrading TDLS chandef when reaching the AP BW. The AP provides
the necessary regulatory protection in this case.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=153961, which
reported an infinite loop here.
Reported-by: Kamil Toman <kamil.toman@gmail.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on which method the driver implements, userspace could
call this (indirectly, by getting station info) before the driver
knows about the station, possibly causing it to misbehave.
Therefore, add a check for sta->uploaded which indicates that the
driver knows about the station.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the code only touches the MAC headers, the offsets to the
network/transport headers remain the same throughout this function.
Remove pointless pieces of code that try to 'preserve' them.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mesh HWMP module will be able to rely on the HW
RC algorithm if it exists, for path metric calculations.
This allows the metric calculation mechanism to calculate
a correct metric, based on PER and last TX rate both via
HW RC algorithm if it exists or via parameters collected
by the SW.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The variable is added to allow the driver an easy access to
it's own hw->priv when the op is invoked.
This fixes a crash in wlcore because it was relying on a
station pointer that wasn't initialized yet. It's the wrong
way to fix the crash, but it solves the problem for now and
it does make sense to have the hw pointer here.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
[rewrite commit message, fix indentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If QoS frame with EOSP (end of service period) subfield=1 sent by local
peer was not acked by remote peer, local peer did not end the MPSP. This
prevents local peer from going to DOZE state. And if the remote peer
goes away without closing connection, local peer continues AWAKE state
and wastes battery.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code currently assumes that buffered multicast PS frames don't have
a pending ACK frame for tx status reporting.
However, hostapd sends a broadcast deauth frame on teardown for which tx
status is requested. This can lead to the "Have pending ack frames"
warning on module reload.
Fix this by using ieee80211_free_txskb/ieee80211_purge_tx_queue.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers (e.g. wl18xx) expect that the last stage in the
de-initialization process will be stopping the beacons, similar to AP flow.
Update ieee80211_stop_mesh() flow accordingly.
As peers can be removed dynamically, this would not impact other drivers.
Tested also on Ralink RT3572 chipset.
Signed-off-by: Maital Hahn <maitalm@ti.com>
Signed-off-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The logic was inverted here, set the bit if frames are pending.
Fixes: ba8c3d6f16 ("mac80211: add an intermediate software queue implementation")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, mesh power management functionality works only with kernel
MPM. Because user space MPM did not report mesh peer AID to kernel,
the kernel could not identify the bit in TIM element. So this patch
adds mesh peer AID setting API.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Continuing the workaround implemented in commit 23665aaf91
("mac80211: Interoperability workaround for 80+80 and 160 MHz channels")
use the same code to parse the Wide Bandwidth Channel Switch element
by converting to VHT Operation element since the spec also just refers
to that for parsing semantics, particularly with the workaround.
While at it, remove some dead code - the IEEE80211_STA_DISABLE_40MHZ
flag can never be set at this point since it's checked earlier and the
wide_bw_chansw_ie pointer is set to NULL if it's set.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the following to support beacon report radio measurement
with the measurement mode field set to passive or active:
1. Propagate the required scan duration to the device
2. Report the scan start time (in terms of TSF)
3. Report each BSS's detection time (also in terms of TSF)
TSF times refer to the BSS that the interface that requested the
scan is connected to.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
[changed ath9k/10k, at76c59x-usb, iwlegacy, wl1251 and wlcore to match
the new API]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Beacon report radio measurement requires reporting observed BSSs
on the channels specified in the beacon request. If the measurement
mode is set to passive or active, it requires actually performing a
scan (passive or active, accordingly), and reporting the time that
the scan was started and the time each beacon/probe was received
(both in terms of TSF of the BSS of the requesting AP). If the
request mode is table, this information is optional.
In addition, the radio measurement request specifies the channel
dwell time for the measurement.
In order to use scan for beacon report when the mode is active or
passive, add a parameter to scan request that specifies the
channel dwell time, and add scan start time and beacon received time
to scan results information.
Supporting beacon report is required for Multi Band Operation (MBO).
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current implementation of handling ADDBA Request while a session
is already active with the peer is wrong - in case the peer is using
the existing session's dialog token this should be treated as update
to the session, which can update the timeout value.
We don't really have a good way of supporting that, so reject, but
implement the required behaviour in the spec of "Even if the updated
ADDBA Request frame is not accepted, the original Block ACK setup
remains active." (802.11-2012 10.5.4)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We've accumulated a couple of different fixes now to mesh_sta_cleanup()
due to the different paths that user_mpm and !user_mpm cases take -- one
fix to flush nexthop paths and one to fix the counting.
The only caller of mesh_plink_deactivate() is mesh_sta_cleanup(), so we
can push the user_mpm checks down into there in order to share more
code.
In doing so, we can remove an extra call to mesh_path_flush_by_nexthop()
and the (unnecessary) call to mesh_accept_plinks_update(). This will
also ensure the powersaving state code gets called in the user_mpm case.
The only cleanup tasks we need to avoid when MPM is in user-space
are sending the peering frames and stopping the plink timer, so wrap
those in the appropriate check.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Previously, the action frames to group address was not encrypted. But
[1] "Table 8-38 Category values" indicates "Mesh" and "Multihop" category
action frames should be encrypted (Group addressed privacy == yes). And the
encyption key should be MGTK ([1] 10.13 Group addressed robust management frame
procedures). So this patch modifies the code to make it suitable for spec.
[1] IEEE Std 802.11-2012
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
We normally return an uninitialized value, but no one checks it so it
doesn't matter. Anyway, let's silence the static checker warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
If a user space program (e.g., wpa_supplicant) deletes a STA entry that
is currently in NL80211_PLINK_ESTAB state, the number of established
plinks counter was not decremented and this could result in rejecting
new plink establishment before really hitting the real maximum plink
limit. For !user_mpm case, this decrementation is handled by
mesh_plink_deactive().
Fix this by decrementing estab_plinks on STA deletion
(mesh_sta_cleanup() gets called from there) so that the counter has a
correct value and the Beacon frame advertisement in Mesh Configuration
element shows the proper value for capability to accept additional
peers.
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
* the biggest change is Michał's work on integrating FQ/codel
with the mac80211 internal software queues
* cfg80211 connect result gets clarified for the
"no connection at all" case
* advertisement of per-interface type capabilities, in case
they differ (which makes a lot of sense for some capabilities)
* most of the nl80211 & hwsim unprivileged namespace operation
changes
* human-readable VHT capabilities in debugfs
* some other cleanups, like spelling
-----BEGIN PGP SIGNATURE-----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=FvhQ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-06-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For the next cycle, we have the following:
* the biggest change is Michał's work on integrating FQ/codel
with the mac80211 internal software queues
* cfg80211 connect result gets clarified for the
"no connection at all" case
* advertisement of per-interface type capabilities, in case
they differ (which makes a lot of sense for some capabilities)
* most of the nl80211 & hwsim unprivileged namespace operation
changes
* human-readable VHT capabilities in debugfs
* some other cleanups, like spelling
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no other limit other than a global
packet count limit when using software queuing.
This means a single flow queue can grow insanely
long. This is particularly bad for TCP congestion
algorithms which requires a little more
sophisticated frame dropping scheme than a mere
headdrop on limit overflow.
Hence apply (a slighly modified, to fit the knobs)
CoDel5 on flow queues. This improves TCP
convergence and stability when combined with
wireless driver which keeps its own tx queue/fifo
at a minimum fill level for given link conditions.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds a debugfs entry to read and modify some fq parameters.
This makes it easy to debug, test and experiment.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[remove module parameter for now]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211's software queues were designed to work
very closely with device tx queues. They are
required to make use of 802.11 packet aggregation
easily and efficiently.
Due to the way 802.11 aggregation is designed it
only makes sense to keep fair queuing as close to
hardware as possible to reduce induced latency and
inertia and provide the best flow responsiveness.
This change doesn't translate directly to
immediate and significant gains. End result
depends on driver's induced latency. Best results
can be achieved if driver keeps its own tx
queue/fifo fill level to a minimum.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Qdiscs are designed with no regard to 802.11
aggregation requirements and hand out
packet-by-packet with no guarantee they are
destined to the same tid. This does more bad than
good no matter how fairly a given qdisc may behave
on an ethernet interface.
Software queuing used per-AC netdev subqueue
congestion control whenever a global AC limit was
hit. This meant in practice a single station or
tid queue could starve others rather easily. This
could resonate with qdiscs in a bad way or could
just end up with poor aggregation performance.
Increasing the AC limit would increase induced
latency which is also bad.
Disabling qdiscs by default and performing
taildrop instead of netdev subqueue congestion
control on the other hand makes it possible for
tid queues to fill up "in the meantime" while
preventing stations starving each other.
This increases aggregation opportunities and
should allow software queuing based drivers
achieve better performance by utilizing airtime
more efficiently with big aggregates.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This makes it a lot easier to understand the capabilities used
by the station:
VHT supported
cap: 0x300819b2
MAX-MPDU-11454
80Mhz
RXLDPC
SHORT-GI-80
TXSTBC
RXSTBC_1
SU-BEAMFORMER-CAPABLE
SU-BEAMFORMEE-CAPABLE
BEAMFORMEE-STS: 0x0
SOUNDING-DIMENSIONS: 0x0
MU-BEAMFORMER-CAPABLE
MPDU-LENGTH-EXPONENT: 0x0
LINK-ADAPTATION-VHT-MRQ-MFB: 0x0
RX-ANTENNA-PATTERN
TX-ANTENNA-PATTERN
RX MCS: fffe
TX MCS: fffe
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The header field is defined as u8[] but also accessed as struct
ieee80211_hdr. Enforce an alignment of 2 to prevent unnecessary
unaligned accesses, which can be very harmful for performance on many
platforms.
Fixes: e495c24731 ("mac80211: extend fast-xmit for more ciphers")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* completion and fixups of nla_put_64_64bit() work
* remove a/b/g/n from wext nickname to avoid confusion
with 11ac (which wouldn't even fit fully there due to
string length restrictions)
along with some other minor changes/cleanups.
-----BEGIN PGP SIGNATURE-----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=QNxF
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-05-12' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Some more work for 4.7, notably:
* completion and fixups of nla_put_64_64bit() work
* remove a/b/g/n from wext nickname to avoid confusion
with 11ac (which wouldn't even fit fully there due to
string length restrictions)
along with some other minor changes/cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When using RSS, frames might not be processed in the correct order,
and thus AP_LINK_PS must be used; most likely with firmware keeping
track of the powersave state, this is the case in iwlwifi now.
In this case, the driver can use ieee80211_sta_ps_transition() to
still have mac80211 manage powersave buffering. However, for U-APSD
and PS-Poll this isn't sufficient. If the device can't manage that
entirely on its own, mac80211's code should be used.
To allow this, export two functions: ieee80211_sta_uapsd_trigger()
and ieee80211_sta_pspoll().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some hardware (iwlwifi an example) de-aggregate AMSDUs and copy the IV
as is to the generated MPDUs, so the same PN appears in multiple
packets without being a replay attack. Allow driver to explicitly
indicate that a frame is allowed to have the same PN as the previous
frame.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases, after a sudden AP disappearing and reconnection to
another AP in the same ESS, user space gets the old AP in scan
results (cached). User space may decide to roam to that old AP
which will cause a disconnection and longer recovery.
Remove APs that are probably out of range from BSS table.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
net/ipv4/ip_gre.c
Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case that dev_alloc_name() fails, e.g. because the name was
given by the user and already exists, we need to clean up properly
and free the per-CPU statistics. Fix that.
Cc: stable@vger.kernel.org
Fixes: 5a490510ba ("mac80211: use per-CPU TX/RX statistics")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This fixes:
net/mac80211/mesh_hwmp.c:603:26: warning: ‘target_metric’ may be used uninitialized in this function
target_metric is only consumed when reply = true so no bug exists here,
but not all versions of gcc realize it. Initialize to 0 to remove the
warning.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Prevents excessive A-MSDU aggregation at low data rates or bad
conditions.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Requires software tx queueing and fast-xmit support. For good
performance, drivers need frag_list support as well. This avoids the
need for copying data of aggregated frames. Running without it is only
supported for debugging purposes.
To avoid performance and packet size issues, the rate control module or
driver needs to limit the maximum A-MSDU size by setting
max_rc_amsdu_len in struct ieee80211_sta.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[fix locking issue]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver advertises the new HW flag USE_RSS, make the
station statistics on the fast-rx path per-CPU. This will
enable calling the RX in parallel, only hitting locking or
shared cachelines when the fast-RX path isn't available.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The regular RX path has a lot of code, but with a few
assumptions on the hardware it's possible to reduce the
amount of code significantly. Currently the assumptions
on the driver are the following:
* hardware/driver reordering buffer (if supporting aggregation)
* hardware/driver decryption & PN checking (if using encryption)
* hardware/driver did de-duplication
* hardware/driver did A-MSDU deaggregation
* AP_LINK_PS is used (in AP mode)
* no client powersave handling in mac80211 (in client mode)
of which some are actually checked per packet:
* de-duplication
* PN checking
* decryption
and additionally packets must
* not be A-MSDU (have been deaggregated by driver/device)
* be data packets
* not be fragmented
* be unicast
* have RFC 1042 header
Additionally dynamically we assume:
* no encryption or CCMP/GCMP, TKIP/WEP/other not allowed
* station must be authorized
* 4-addr format not enabled
Some data needed for the RX path is cached in a new per-station
"fast_rx" structure, so that we only need to look at this and
the packet, no other memory when processing packets on the fast
RX path.
After doing the above per-packet checks, the data path collapses
down to a pretty simple conversion function taking advantage of
the data cached in the small fast_rx struct.
This should speed up the RX processing, and will make it easier
to reason about parallelizing RX (for which statistics will need
to be per-CPU still.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On 32-bit platforms, the 64-bit counters we keep need to be protected
to be consistently read. Use the u64_stats_sync mechanism to do that.
In order to not end up with overly long lines, refactor the tidstats
assignments a bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When storing the last_rate_* values in the RX code, there's nothing
to guarantee consistency, so a concurrent reader could see, e.g.
last_rate_idx on the new value, but last_rate_flag still on the old,
getting completely bogus values in the end.
To fix this, I lifted the sta_stats_encode_rate() function from my
old rate statistics code, which encodes the entire rate data into a
single 16-bit value, avoiding the consistency issue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of touching the rx_stats.last_rx from the status path, introduce
and use a status_stats.last_ack variable. This will make rx_stats.last_rx
indicate when the last frame was received, making it available for real
"last_rx" and statistics gathering; statistics, when done per-CPU, will
need to figure out which place was updated last for those items where the
"last" value is exposed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to update rx_stats.last_rx after allocating
a station since it's already updated during allocation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the averaged values out of rx_stats and into rx_stats_avg,
to cleanly split them out. The averaged ones cannot be supported
for parallel RX in a per-CPU fashion, while the other values can
be collected per CPU and then combined/selected when needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the semicolon, people typically assume that and
once line already put a semicolon behind the "call".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For the RX MSDU statistics, we need to count the number of
MSDUs created and accepted from an A-MSDU. Right now, all
frames in any A-MSDUs were completely ignored. Fix this by
moving the RX MSDU statistics accounting into the deliver
function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes drivers already looked up, or know out-of-band
from their device, which station transmitted a given RX
frame. Allow them to pass the station pointer to mac80211
to save the extra lookup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Lockdep warned of a lock dependency between the mesh_plink lock
and the internal lock for the rhashtable. The problem is that
the rhashtable code uses a spin lock with softirqs enabled, while
mesh_plink_timer executes a walk (to flush paths on a state change)
inside a softirq with the plink lock held.
This leads to the following deadlock if the timer fires while rht
lock is held on this CPU, and plink lock is held on another CPU:
CPU0 CPU1
---- ----
lock(&(&ht->lock)->rlock);
local_irq_disable();
lock(&(&sta->mesh->plink_lock)->rlock);
lock(&(&ht->lock)->rlock);
<Interrupt>
lock(&(&sta->mesh->plink_lock)->rlock);
*** DEADLOCK ***
Fix by waiting until we drop the plink lock to flush paths.
Fixes: d48a1b7cd439 ("mac80211: mesh: convert path table to rhashtable")
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Several of the mesh path fields are undocumented and some
of the documentation is no longer correct or relevant after
the switch to rhashtable. Clean up the kernel doc
accordingly and reorder some fields to match the structure
layout.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reduce padding waste in struct mesh_table and struct rmc_entry by
moving the smaller fields to the end.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we have converted the mesh path tables to rhashtable, we are
no longer swapping out the entire mesh_pathtbl pointer with RCU.
As a result, we no longer need indirection to the hlist head for
the gates list and can simply embed it, saving a pair of
pointer-sized allocations.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The RMC cache has 256 list heads plus a u32, which puts it at the
unfortunate size of 4104 bytes with padding. kmalloc() will then
round this up to the next power-of-two, so we wind up actually
using two pages here where most of the second is wasted.
Switch to hlist heads here to reduce the structure size down to
fit within a page.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the unlikely case that mesh_rmc_init() fails with -ENOMEM,
the rmc pointer will be left as NULL but the interface is still
operational because ieee80211_mesh_init_sdata() is not allowed
to fail.
If this happens, we would blindly dereference rmc when checking
whether a multicast frame is in the cache. Instead just drop the
frames in the forwarding path.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Legacy clients don't support P2P power save mechanism, and thus if a P2P GO
has a legacy client connected to it, it should disable P2P PS mechanisms.
Let the driver know about this with a new bss_conf parameter.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the likely case that probe_count is 0, don't write to the
memory there.
Also use ifmgd consistently in the function, instead of using
sdata->u.mgd as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code is only used with iwlwifi, but still should have proper
mac80211 naming scheme; fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Avoid the really strange %s%s%s expression, use an array
of flag names and check that all flags are present.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the device implements dynamic PS itself, there's no need
to ever start the dynamic powersave timer on RX.
While at it, fix up some indentation in this code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the previous patch, the struct only has a single member,
so remove the struct and leave just the single member.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove unused variable in per STA debugfs structure, 'commit 34e895075e
("mac80211: allow station add/remove to sleep")' removed the only user of
'add_has_run'.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the debugfs entry for starting aggregation session
starts it with timeout of 5 seconds. Allow opening a session
with a custom timeout (according to spec 0 is no timeout).
while at it, refactor the function and remove the magic numbers.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
NETIF_F_RXCSUM is not in the white list, though some
drivers may want to set it in order to enable seeing the
actual RX checksum status in ethtool.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow publishing RRM capabilities for features that are not
HW dependent.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There were a few issues that were slowing down the process of finding
the optimal rate, especially on devices with multi-rate retry
limitations:
When max_tp_rate[0] was slower than max_tp_rate[1], the code did not
sample max_tp_rate[1], which would often allow it to switch places with
max_tp_rate[0] (e.g. if only the first sampling attempts were bad, but the
rate is otherwise good).
Also, sample attempts of rates between max_tp_rate[0] and [1] were being
ignored in this case, because the code only checked if the rate was
slower than [1].
Fix this by checking against the fastest / second fastest max_tp_rate
instead of assuming a specific order between the two.
In my tests this patch significantly reduces the time until minstrel_ht
finds the optimal rate right after assoc
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we enqueued the frame that was supposed to be sent
during the SP, and that frame may very well cary the
IEEE80211_TX_STATUS_EOSP bit, we may never close the SP
(WLAN_STA_SP will never be cleared). If that happens, we
will not open any new SP and will never respond to any poll
frame from the client.
Clear WLAN_STA_SP manually if a frame that was polled during
the SP is queued because of a starting A-MPDU session. The
client may not see the EOSP bit, but it will at least be
able to poll new frames in another SP.
Reported-by: Alesya Shapira <alesya.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[remove erroneous comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is possible that the station is connected to an AP
with bandwidth of 80+80MHz or 160MHz. In such cases
there is no need to perform an upgrade as the maximal
supported bandwidth is 80MHz.
In addition, when upgrading and setting center_freq1
and bandwidth to 80MHz also set center_freq2 to 0.
Fixes: 0fabfaafec ("mac80211: upgrade BW of TDLS peers when possible"
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Frames that are sent between
ampdu_action(IEEE80211_AMPDU_TX_START) and the move to the
HT_AGG_STATE_OPERATIONAL state are buffered.
If we try to start an A-MPDU session while the peer is
sleeping and polling frames with U-APSD, we may have frames
that will be buffered by ieee80211_tx_prep_agg. These frames
have IEEE80211_TX_CTL_NO_PS_BUFFER set since they are sent to
a sleeping client and possibly IEEE80211_TX_STATUS_EOSP.
If the frame is buffered, we need clear these two flags
since they will be re-sent after the move to
HT_AGG_STATE_OPERATIONAL state which is very likely to
happen after the SP ends.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 976bd9efda ("mac80211: move beacon_loss_count into ifmgd")
removed the member from the sta_info struct but the description stayed
lingering. Remove it.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
By default, the rhashtable logic will fail to insert
objects if the key-chains are too long and un-balanced.
In the degenerate case where mac80211 is creating many
virtual interfaces connected to the same peer(s), this
case can happen.
St insecure_elasticity to true to allow chains to grow
as long as needed.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[remove message, change commit message slightly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The original hand-implemented hash-table in mac80211 couldn't result
in insertion errors, and while converting to rhashtable I evidently
forgot to check the errors.
This surfaced now only because Ben is adding many identical keys and
that resulted in hidden insertion errors.
Cc: stable@vger.kernel.org
Fixes: 7bedd0cfad ("mac80211: use rhashtable for station table")
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fall back to rate control if the requested bitrate was not found.
Fixes: dfdfc2beb0 ("mac80211: Parse legacy and HT rate in injected frames")
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The MCS bandwidth part of the radiotap header is 2 bits wide. The full 2
bit have to compared against IEEE80211_RADIOTAP_MCS_BW_40 and not only if
the first bit is set. Otherwise IEEE80211_RADIOTAP_MCS_BW_40 can be
confused with IEEE80211_RADIOTAP_MCS_BW_20U.
Fixes: dfdfc2beb0 ("mac80211: Parse legacy and HT rate in injected frames")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices, like iwlwifi, have RSS queues. This may cause a
situation where a disassociation is handled in control path and
results in station removal while there are prior RX frames
that were still not processed in other queues. When they will
be processed the station will be gone, and the frames will be
dropped.
Add a synchronization interface to avoid that. When driver returns
from the synchronization mac80211 may remove the station.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the time since the mesh path table was implemented as an
RCU-traversable, dynamically growing hash table, a generic RCU
hashtable implementation was added to the kernel.
Switch the mesh path table over to rhashtable to remove some code
and also gain some features like automatic shrinking.
Cc: Thomas Graf <tgraf@suug.ch>
Cc: netdev@vger.kernel.org
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mesh path table uses a struct mesh_node in its hlists in
order to support a resizable hash table: the mesh_node provides
an indirection to the actual mesh path so that two different
bucket lists can point to the same path entry.
However, for the known gates list, we don't need this indirection
because there is ever only one list. So we can just embed the
hlist_node in the mesh path itself, which simplifies things a bit
and saves a linear search whenever we need to find an item in
the list.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove duplicate code to allocate and initialize a mesh
path or mesh proxy path.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that the sdata pointer is the same for all entries of a
path table, hashing it is pointless, so hash only the address.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mesh path and mesh gate hashtables are global, containing
all of the mpaths for every mesh interface, but the paths are
all tied logically to a single interface. The common case is
just a single mesh interface, so optimize for that by moving
the global hashtable into the per-interface struct.
Doing so allows us to drop sdata pointer comparisons inside
the lookups and also saves a few bytes of BSS and data.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the cfg80211 scan trigger operation specifies a single BSSID, use
that value instead of the wildcard BSSID in the Probe Request frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The min_def chanctx is affected not only by the current chandef, but
sometimes also by other stations on the vif. There's a valid scenario
where a TDLS peer can widen its BW, thereby causing the min_def
to increase.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The previous approach simply ignored chandef restrictions when calculating
the appropriate peer BW for a WIDER_BW peer. This could result in a
regulatory violation if both peers indicated 80MHz support, but the
regdomain forbade it.
Change the approach to setting a WIDER_BW peer's BW. Don't exempt it from
the chandef width at first. If during TDLS negotiation the chandef width
is upgraded, update the peer's BW to match.
Fixes: 0fabfaafec ("mac80211: upgrade BW of TDLS peers when possible")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even if the current chandef width is equal to the station's max-BW, it
doesn't mean it's a valid width for TDLS. Make sure to always check
regulatory constraints in these cases.
Fixes: 0fabfaafec ("mac80211: upgrade BW of TDLS peers when possible")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Buffered multicast frames must be passed to the driver directly via
drv_tx instead of going through the txq, otherwise they cannot easily be
scheduled to be sent after DTIM.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When HW crypto is used, there's no need for the CCMP/GCMP MIC to
be available to mac80211, and the hardware might have removed it
already after checking. The MIC is also useless to have when the
frame is already decrypted, so allow indicating that it's not
present.
Since we are running out of bits in mac80211_rx_flags, make
the flags field a u64.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This was requested by Android, and the appropriate cfg80211 API
had been added by Dmitry. Support it in mac80211, allowing drivers
to provide the timestamp.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add VHT radiotap parsing support to ieee80211_parse_tx_radiotap().
That capability has been tested using a d-link dir-860l rev b1 running
OpenWrt trunk and mt76 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since offset is zero, it's not necessary to use set function. Reset
function is straightforward, and will remove the unnecessary add
operation in set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* check GCMP encryption vs. fragmentation properly; we'd found
this problem quite a while ago but waited for the 802.11 spec
to be updated
* fix RTS/CTS logic in minstrel_ht
* fix RX of certain public action frames in AP mode
* add mac80211_hwsim to MAC80211 in MAINTAINERS, this helps
the kbuild robot pick up the right tree for it
-----BEGIN PGP SIGNATURE-----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=2rZC
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2016-03-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Here are a few more fixes for the current cycle:
* check GCMP encryption vs. fragmentation properly; we'd found
this problem quite a while ago but waited for the 802.11 spec
to be updated
* fix RTS/CTS logic in minstrel_ht
* fix RX of certain public action frames in AP mode
* add mac80211_hwsim to MAC80211 in MAINTAINERS, this helps
the kbuild robot pick up the right tree for it
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
RTS/CTS needs to be enabled if the rate is a fallback rate *or* if it's
a dual-stream rate and the sta is in dynamic SMPS mode.
Cc: stable@vger.kernel.org
Fixes: a3ebb4e1b7 ("mac80211: minstrel_ht: handle peers in dynamic SMPS")
Reported-by: Matías Richart <mrichart@fing.edu.uy>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Public Action frames use special rules for how the BSSID field (Address
3) is set. A wildcard BSSID is used in cases where the transmitter and
recipient are not members of the same BSS. As such, we need to accept
Public Action frames with wildcard BSSID.
Commit db8e173245 ("mac80211: ignore frames between TDLS peers when
operating as AP") added a rule that drops Action frames to TDLS-peers
based on an Action frame having different DA (Address 1) and BSSID
(Address 3) values. This is not correct since it misses the possibility
of BSSID being a wildcard BSSID in which case the Address 1 would not
necessarily match.
Fix this by allowing mac80211 to accept wildcard BSSID in an Action
frame when in AP mode.
Fixes: db8e173245 ("mac80211: ignore frames between TDLS peers when operating as AP")
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Just like for CCMP we need to check that for GCMP the fragments
have PNs that increment by one; the spec was updated to fix this
security issue and now has the following text:
The receiver shall discard MSDUs and MMPDUs whose constituent
MPDU PN values are not incrementing in steps of 1.
Adapt the code for CCMP to work for GCMP as well, luckily the
relevant fields already alias each other so no code duplication
is needed (just check the aliasing with BUILD_BUG_ON.)
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* stop critical protocol session on disconnect to avoid
it getting stuck
* wext: fix two RTNL message ordering issues
* fix an uninitialized value (found by KASAN)
* fix an out-of-bounds access (also found by KASAN)
* clear connection keys when freeing them in all cases
(IBSS, all other places already did so)
* fix expected throughput unit to get consistent values
* set default TX aggregation timeout to 0 in minstrel
to avoid (really just hide) issues and perform better
-----BEGIN PGP SIGNATURE-----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=01n9
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2016-02-23' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Another small set of fixes:
* stop critical protocol session on disconnect to avoid
it getting stuck
* wext: fix two RTNL message ordering issues
* fix an uninitialized value (found by KASAN)
* fix an out-of-bounds access (also found by KASAN)
* clear connection keys when freeing them in all cases
(IBSS, all other places already did so)
* fix expected throughput unit to get consistent values
* set default TX aggregation timeout to 0 in minstrel
to avoid (really just hide) issues and perform better
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers may need to track which vif is using VHT MU-MIMO.
Move the flag indicationg the ownership of MU_MIMO to
ieee80211_vif.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Provide an interface to the lower level driver to set the VHT
MU-MIMO data. This is needed for example when there is an update
of the group data during low power state, where the management
frame will not be passed to the host at all.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the PNs of all the tx keys are now tracked in the public
part of the key struct (with atomic counter), we no longer
need these functions.
dvm and vt665{5,6} are currently the only users of these functions,
so update them accordingly.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers/devices might want to set the IVs by
themselves (and still let mac80211 generate MMIC).
Specifically, this is needed when the device does
offloading at certain times, and the driver has
to make sure that the IVs of new tx frames (from
the host) are synchronized with IVs that were
potentially used during the offloading.
Similarly to CCMP, move the TX IVs of TKIP keys to the
public part of the key struct, and export a function
to add the IV right into the crypto header.
The public tx_pn field is defined as atomic64, so define
TKIP_PN_TO_IV16/32 helper macros to convert it to iv16/32
when needed.
Since the iv32 used for the p1k cache is taken
directly from the frame, we can safely remove
iv16/32 from being protected by tkip.txlock.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix wiphy supported_band access in tx radiotap parsing introduced
in commit 5ec3aed9ba4c ("mac80211: Parse legacy and HT rate in
injected frames"). In particular, info->band is always set to 0
(IEEE80211_BAND_2GHZ) since it has not assigned yet.
This cause a kernel crash on 5GHz only devices.
Move ieee80211_parse_tx_radiotap() after info->band assignment
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The source and destintation addresses in the memcpy arguments
are flipped. Fix that.
Fixes: 23a1f8d44c0b("mac80211: process and save VHT MU-MIMO group frame")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mpp_path_del() and mesh_path_del() are mostly the same function.
Move common code into a new static function.
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Henning Rogge <henning.rogge@fkie.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau