Commit Graph

24 Commits

Author SHA1 Message Date
Vladimir Oltean 21ce7f3e16 net: dsa: ocelot: the MAC table on Felix is twice as large
When running 'bridge fdb dump' on Felix, sometimes learnt and static MAC
addresses would appear, sometimes they wouldn't.

Turns out, the MAC table has 4096 entries on VSC7514 (Ocelot) and 8192
entries on VSC9959 (Felix), so the existing code from the Ocelot common
library only dumped half of Felix's MAC table. They are both organized
as a 4-way set-associative TCAM, so we just need a single variable
indicating the correct number of rows.

Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-06 17:15:24 -07:00
Vladimir Oltean 87b0f983f6 net: mscc: ocelot: fix untagged packet drops when enslaving to vlan aware bridge
To rehash a previous explanation given in commit 1c44ce560b ("net:
mscc: ocelot: fix vlan_filtering when enslaving to bridge before link is
up"), the switch driver operates the in a mode where a single VLAN can
be transmitted as untagged on a particular egress port. That is the
"native VLAN on trunk port" use case.

The configuration for this native VLAN is driven in 2 ways:
 - Set the egress port rewriter to strip the VLAN tag for the native
   VID (as it is egress-untagged, after all).
 - Configure the ingress port to drop untagged and priority-tagged
   traffic, if there is no native VLAN. The intention of this setting is
   that a trunk port with no native VLAN should not accept untagged
   traffic.

Since both of the above configurations for the native VLAN should only
be done if VLAN awareness is requested, they are actually done from the
ocelot_port_vlan_filtering function, after the basic procedure of
toggling the VLAN awareness flag of the port.

But there's a problem with that simplistic approach: we are trying to
juggle with 2 independent variables from a single function:
 - Native VLAN of the port - its value is held in port->vid.
 - VLAN awareness state of the port - currently there are some issues
   here, more on that later*.
The actual problem can be seen when enslaving the switch ports to a VLAN
filtering bridge:
 0. The driver configures a pvid of zero for each port, when in
    standalone mode. While the bridge configures a default_pvid of 1 for
    each port that gets added as a slave to it.
 1. The bridge calls ocelot_port_vlan_filtering with vlan_aware=true.
    The VLAN-filtering-dependent portion of the native VLAN
    configuration is done, considering that the native VLAN is 0.
 2. The bridge calls ocelot_vlan_add with vid=1, pvid=true,
    untagged=true. The native VLAN changes to 1 (change which gets
    propagated to hardware).
 3. ??? - nobody calls ocelot_port_vlan_filtering again, to reapply the
    VLAN-filtering-dependent portion of the native VLAN configuration,
    for the new native VLAN of 1. One can notice that after toggling "ip
    link set dev br0 type bridge vlan_filtering 0 && ip link set dev br0
    type bridge vlan_filtering 1", the new native VLAN finally makes it
    through and untagged traffic finally starts flowing again. But
    obviously that shouldn't be needed.

So it is clear that 2 independent variables need to both re-trigger the
native VLAN configuration. So we introduce the second variable as
ocelot_port->vlan_aware.

*Actually both the DSA Felix driver and the Ocelot driver already had
each its own variable:
 - Ocelot: ocelot_port_private->vlan_aware
 - Felix: dsa_port->vlan_filtering
but the common Ocelot library needs to work with a single, common,
variable, so there is some refactoring done to move the vlan_aware
property from the private structure into the common ocelot_port
structure.

Fixes: 97bb69e1e3 ("net: mscc: ocelot: break apart ocelot_vlan_port_apply")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-15 12:27:35 -07:00
Vladimir Oltean fc411eaac8 net: dsa: felix: add port policers
This patch is a trivial passthrough towards the ocelot library, which
support port policers since commit 2c1d029a01 ("net: mscc: ocelot:
Implement port policers via tc command").

Some data structure conversion between the DSA core and the Ocelot
library is necessary, for policer parameters.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-30 11:44:00 -07:00
Xiaoliang Yang c9a7fe1238 net: mscc: ocelot: add action of police on vcap_is2
Ocelot has 384 policers that can be allocated to ingress ports,
QoS classes per port, and VCAP IS2 entries. ocelot_police.c
supports to set policers which can be allocated to police action
of VCAP IS2. We allocate policers from maximum pol_id, and
decrease the pol_id when add a new vcap_is2 entry which is
police action.

Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-30 11:44:00 -07:00
Vladimir Oltean 0b912fc93a net: dsa: felix: support changing the MTU
Changing the MTU for this switch means altering the
DEV_GMII:MAC_CFG_STATUS:MAC_MAXLEN_CFG field MAX_LEN, which in turn
limits the size of frames that can be received.

Special accounting needs to be done for the DSA CPU port (NPI port in
hardware terms). The NPI port configuration needs to be held inside the
private ocelot structure, since it is now accessed from multiple places.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-27 16:07:25 -07:00
David S. Miller 1d34357931 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Minor overlapping changes, nothing serious.

Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-12 22:34:48 -07:00
Vladimir Oltean a8015ded89 net: mscc: ocelot: properly account for VLAN header length when setting MRU
What the driver writes into MAC_MAXLEN_CFG does not actually represent
VLAN_ETH_FRAME_LEN but instead ETH_FRAME_LEN + ETH_FCS_LEN. Yes they are
numerically equal, but the difference is important, as the switch treats
VLAN-tagged traffic specially and knows to increase the maximum accepted
frame size automatically. So it is always wrong to account for VLAN in
the MAC_MAXLEN_CFG register.

Unconditionally increase the maximum allowed frame size for
double-tagged traffic. Accounting for the additional length does not
mean that the other VLAN membership checks aren't performed, so there's
no harm done.

Also, stop abusing the MTU name for configuring the MRU. There is no
support for configuring the MRU on an interface at the moment.

Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Fixes: fa914e9c4d ("net: mscc: ocelot: create a helper for changing the port MTU")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-09 18:58:17 -07:00
Vladimir Oltean 1cf3299b03 net: dsa: felix: Allow unknown unicast traffic towards the CPU port module
Compared to other DSA switches, in the Ocelot cores, the RX filtering is
a much more important concern.

Firstly, the primary use case for Ocelot is non-DSA, so there isn't any
secondary Ethernet MAC [the DSA master's one] to implicitly drop frames
having a DMAC we are not interested in.  So the switch driver itself
needs to install FDB entries towards the CPU port module (PGID_CPU) for
the MAC address of each switch port, in each VLAN installed on the port.
Every address that is not whitelisted is implicitly dropped. This is in
order to achieve a behavior similar to N standalone net devices.

Secondly, even in the secondary use case of DSA, such as illustrated by
Felix with the NPI port mode, that secondary Ethernet MAC is present,
but its RX filter is bypassed. This is because the DSA tags themselves
are placed before Ethernet, so the DMAC that the switch ports see is
not seen by the DSA master too (since it's shifter to the right).

So RX filtering is pretty important. A good RX filter won't bother the
CPU in case the switch port receives a frame that it's not interested
in, and there exists no other line of defense.

Ocelot is pretty strict when it comes to RX filtering: non-IP multicast
and broadcast traffic is allowed to go to the CPU port module, but
unknown unicast isn't. This means that traffic reception for any other
MAC addresses than the ones configured on each switch port net device
won't work. This includes use cases such as macvlan or bridging with a
non-Ocelot (so-called "foreign") interface. But this seems to be fine
for the scenarios that the Linux system embedded inside an Ocelot switch
is intended for - it is simply not interested in unknown unicast
traffic, as explained in Allan Nielsen's presentation [0].

On the other hand, the Felix DSA switch is integrated in more
general-purpose Linux systems, so it can't afford to drop that sort of
traffic in hardware, even if it will end up doing so later, in software.

Actually, unknown unicast means more for Felix than it does for Ocelot.
Felix doesn't attempt to perform the whitelisting of switch port MAC
addresses towards PGID_CPU at all, mainly because it is too complicated
to be feasible: while the MAC addresses are unique in Ocelot, by default
in DSA all ports are equal and inherited from the DSA master. This adds
into account the question of reference counting MAC addresses (delayed
ocelot_mact_forget), not to mention reference counting for the VLAN IDs
that those MAC addresses are installed in. This reference counting
should be done in the DSA core, and the fact that it wasn't needed so
far is due to the fact that the other DSA switches don't have the DSA
tag placed before Ethernet, so the DSA master is able to whitelist the
MAC addresses in hardware.

So this means that even regular traffic termination on a Felix switch
port happens through flooding (because neither Felix nor Ocelot learn
source MAC addresses from CPU-injected frames).

So far we've explained that whitelisting towards PGID_CPU:
- helps to reduce the likelihood of spamming the CPU with frames it
  won't process very far anyway
- is implemented in the ocelot driver
- is sufficient for the ocelot use cases
- is not feasible in DSA
- breaks use cases in DSA, in the current status (whitelisting enabled
  but no MAC address whitelisted)

So the proposed patch allows unknown unicast frames to be sent to the
CPU port module. This is done for the Felix DSA driver only, as Ocelot
seems to be happy without it.

[0]: https://www.youtube.com/watch?v=B1HhxEcU7Jg

Suggested-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-04 14:19:01 -08:00
Vladimir Oltean 69df578c5f net: mscc: ocelot: eliminate confusion between CPU and NPI port
Ocelot has the concept of a CPU port. The CPU port is represented in the
forwarding and the queueing system, but it is not a physical device. The
CPU port can either be accessed via register-based injection/extraction
(which is the case of Ocelot), via Frame-DMA (similar to the first one),
or "connected" to a physical Ethernet port (called NPI in the datasheet)
which is the case of the Felix DSA switch.

In Ocelot the CPU port is at index 11.
In Felix the CPU port is at index 6.

The CPU bit is treated special in the forwarding, as it is never cleared
from the forwarding port mask (once added to it). Other than that, it is
treated the same as a normal front port.

Both Felix and Ocelot should use the CPU port in the same way. This
means that Felix should not use the NPI port directly when forwarding to
the CPU, but instead use the CPU port.

This patch is fixing this such that Felix will use port 6 as its CPU
port, and just use the NPI port to carry the traffic.

Therefore, eliminate the "ocelot->cpu" variable which was holding the
index of the NPI port for Felix, and the index of the CPU port module
for Ocelot, so the variable was actually configuring different things
for different drivers and causing at least part of the confusion.

Also remove the "ocelot->num_cpu_ports" variable, which is the result of
another confusion. The 2 CPU ports mentioned in the datasheet are
because there are two frame extraction channels (register based or DMA
based). This is of no relevance to the driver at the moment, and
invisible to the analyzer module.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Suggested-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-04 14:19:00 -08:00
Vladimir Oltean 07d985eef0 net: dsa: felix: Wire up the ocelot cls_flower methods
Export the cls_flower methods from the ocelot driver and hook them up to
the DSA passthrough layer.

Tables for the VCAP IS2 parameters, as well as half key packing (field
offsets and lengths) need to be defined for the VSC9959 core, as they
are different from Ocelot, mainly due to the different port count.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03 18:57:49 -08:00
Vladimir Oltean 8551cdeb2a net: mscc: ocelot: parameterize the vcap_is2 properties
Remove the definitions for the VCAP IS2 table from ocelot_ace.c, since
it is specific to VSC7514.

The VSC9959 VCAP IS2 table supports more rules (1024 instead of 64) and
has a different width for the action (89 bits instead of 99).

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03 18:57:49 -08:00
Vladimir Oltean 1ba8f6561a net: mscc: ocelot: remove port_pcs_init indirection for VSC7514
The Felix driver is now using its own PHYLINK instance, not calling into
ocelot_adjust_link. So the port_pcs_init function pointer is an
unnecessary indirection. Remove it.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03 18:57:42 -08:00
Vladimir Oltean e0632940bc net: mscc: ocelot: don't rely on preprocessor for vcap key/action packing
The IGR_PORT_MASK key width is different between the 11-port VSC7514 and
the 6-port VSC9959 switches. And since IGR_PORT_MASK is one of the first
fields of a VCAP key entry, it means that all further field
offset/length pairs are shifted between the 2.

The ocelot driver performs packing of VCAP half keys with the help of
some preprocessor macros:

- A set of macros for defining the HKO (Half Key Offset) and HKL (Half
  Key Length) of each possible key field. The offset of each field is
  defined as the sum between the offset and the sum of the previous
  field.

- A set of accessors on top of vcap_key_set for shorter (aka less
  typing) access to the HKO and HKL of each key field.

Since the field offsets and lengths are different between switches,
defining them through the preprocessor isn't going to fly. So introduce
a structure holding (offset, length) pairs and instantiate it in
ocelot_board.c for VSC7514. In a future patch, a similar structure will
be instantiated in felix_vsc9959.c for NXP LS1028A.

The accessors also need to go. They are based on macro name
concatenation, which is horrible to understand and follow.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03 18:57:42 -08:00
Vladimir Oltean a56d7a345d net: mscc: ocelot: simplify tc-flower offload structures
The ocelot tc-flower offload binds a second flow block callback (apart
from the one for matchall) just because it uses a different block
private structure (ocelot_port_private for matchall, ocelot_port_block
for flower).

But ocelot_port_block just appears to be boilerplate, and doesn't help
with anything in particular at all, it's just useless glue between the
(global!) struct ocelot_acl_block *block pointer, and a per-netdevice
struct ocelot_port_private *priv.

So let's just simplify that, and make struct ocelot_port_private be the
private structure for the block offload. This makes us able to use the
same flow callback as in the case of matchall.

This also reveals that the struct ocelot_acl_block *block is used rather
strangely, as mentioned above: it is defined globally, allocated at
probe time, and freed at unbind time. So just move the structure to the
main ocelot structure, which gives further opportunity for
simplification.

Also get rid of backpointers from struct ocelot_acl_block and struct
ocelot_ace_rule back to struct ocelot, by reworking the function
prototypes, where necessary, to use a more DSA-friendly "struct ocelot
*ocelot, int port" format.

And finally, remove the debugging prints that were added during
development, since they provide no useful information at this point.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03 18:57:29 -08:00
Vladimir Oltean 964ee5c82b net: mscc: ocelot: export ANA, DEV and QSYS registers to include/soc/mscc
Since the Felix DSA driver is implementing its own PHYLINK instance due
to SoC differences, it needs access to the few registers that are
common, mainly for flow control.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-05 23:22:33 -08:00
Vladimir Oltean ee50d07c9f net: mscc: ocelot: make phy_mode a member of the common struct ocelot_port
The Ocelot switchdev driver and the Felix DSA one need it for different
reasons. Felix (or at least the VSC9959 instantiation in NXP LS1028A) is
integrated with the traditional NXP Layerscape PCS design which does not
support runtime configuration of SerDes protocol. So it needs to
pre-validate the phy-mode from the device tree and prevent PHYLINK from
attempting to change it. For this, it needs to cache it in a private
variable.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-05 23:22:33 -08:00
Yangbo Lu b049da1338 net: mscc: ocelot: use skb queue instead of skbs list
Convert to use skb queue instead of the list of skbs.
The skb queue could provide protection with lock.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-27 10:53:37 -08:00
Yangbo Lu 400928bf92 net: mscc: ocelot: convert to use ocelot_port_add_txtstamp_skb()
Convert to use ocelot_port_add_txtstamp_skb() for adding skbs which
require TX timestamp into list. Export it so that DSA Felix driver
could reuse it too.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-21 14:39:02 -08:00
Yangbo Lu e23a7b3e8d net: mscc: ocelot: convert to use ocelot_get_txtstamp()
The method getting TX timestamp by reading timestamp FIFO and
matching skbs list is common for DSA Felix driver too.
So move code out of ocelot_board.c, convert to use
ocelot_get_txtstamp() function and export it.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-21 14:39:02 -08:00
Yangbo Lu f145922ddc net: mscc: ocelot: export ocelot_hwstamp_get/set functions
Export ocelot_hwstamp_get/set functions so that DSA driver
is able to reuse them.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-21 14:39:02 -08:00
Vladimir Oltean a030dfe194 net: mscc: ocelot: publish ocelot_sys.h to include/soc/mscc
The Felix DSA driver needs to write to SYS_RAM_INIT_RAM_INIT for its own
chip initialization process.

Also update the MAINTAINERS file such that the headers exported by the
ocelot driver are under the same maintainers' umbrella as the driver
itself.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-15 12:32:16 -08:00
Vladimir Oltean 5e25636502 net: mscc: ocelot: publish structure definitions to include/soc/mscc/ocelot.h
We will be registering another switch driver based on ocelot, which
lives under drivers/net/dsa.

Make sure the Felix DSA front-end has the necessary abstractions to
implement a new Ocelot driver instantiation. This includes the function
prototypes for implementing DSA callbacks.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-15 12:32:16 -08:00
Quentin Schulz 66c2132333 net: mscc: ocelot: simplify register access for PLL5 configuration
Since HSIO address space can be accessed by different drivers, let's
simplify the register address definitions so that it can be easily used
by all drivers and put the register address definition in the
include/soc/mscc/ocelot_hsio.h header file.

Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-05 14:36:44 -07:00
Quentin Schulz 8afc978925 net: mscc: ocelot: move the HSIO header to include/soc
Since HSIO address space can be used by different drivers (PLL, SerDes
muxing, temperature sensor), let's move it somewhere it can be included
by all drivers.

Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-05 14:36:44 -07:00