commit 5d69d5a00f80488ddcb4dee7d1374a0709398178 upstream.
It was observed that issuing the ABORT bit (IC_ENABLE[1]) will not
work when IC_ENABLE is already disabled.
Check if the ENABLE bit (IC_ENABLE[0]) is disabled when the controller
is holding SCL low. If the ENABLE bit is disabled, the software needs
to enable it before trying to issue the ABORT bit. otherwise,
the controller ignores any write to ABORT bit.
These kernel logs show up whenever an I2C transaction is
attempted after this failure.
i2c_designware e95e0000.i2c: timeout waiting for bus ready
i2c_designware e95e0000.i2c: timeout in disabling adapter
The patch fixes the issue where the controller cannot be disabled
while SCL is held low if the ENABLE bit is already disabled.
Fixes: 2409205acd ("i2c: designware: fix __i2c_dw_disable() in case master is holding SCL low")
Signed-off-by: Kimriver Liu <kimriver.liu@siengine.com>
Cc: <stable@vger.kernel.org> # v6.6+
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c8d604dea437b69a861479b413d629bc9b3da70 upstream.
It is not valid to call pm_runtime_set_suspended() for devices
with runtime PM enabled because it returns -EAGAIN if it is enabled
already and working. So, call pm_runtime_disable() before to fix it.
Fixes: 36ecbcab84 ("i2c: xiic: Implement power management")
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 521da1e9225450bd323db5fa5bca942b1dc485b7 upstream.
Frequently an I2C write will be followed by a read, such as a register
address write followed by a read of the register value. In this driver,
when the TX FIFO half empty interrupt was raised and it was determined
that there was enough space in the TX FIFO to send the following read
command, it would do so without waiting for the TX FIFO to actually
empty.
Unfortunately it appears that in some cases this can result in a NAK
that was raised by the target device on the write, such as due to an
unsupported register address, being ignored and the subsequent read
being done anyway. This can potentially put the I2C bus into an
invalid state and/or result in invalid read data being processed.
To avoid this, once a message has been fully written to the TX FIFO,
wait for the TX FIFO empty interrupt before moving on to the next
message, to ensure NAKs are handled properly.
Fixes: e1d5b6598c ("i2c: Add support for Xilinx XPS IIC Bus Interface")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Cc: <stable@vger.kernel.org> # v2.6.34+
Reviewed-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e2c85d85a05f16af2223fcc0195ff50a7938b372 upstream.
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable when request IRQ.
Fixes: 37692de5d5 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Cc: <stable@vger.kernel.org> # v4.19+
Acked-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 048bbbdbf85e5e00258dfb12f5e368f908801d7b upstream.
In case there is any sort of clock controller attached to this I2C bus
controller, for example Versaclock or even an AIC32x4 I2C codec, then
an I2C transfer triggered from the clock controller clk_ops .prepare
callback may trigger a deadlock on drivers/clk/clk.c prepare_lock mutex.
This is because the clock controller first grabs the prepare_lock mutex
and then performs the prepare operation, including its I2C access. The
I2C access resumes this I2C bus controller via .runtime_resume callback,
which calls clk_prepare_enable(), which attempts to grab the prepare_lock
mutex again and deadlocks.
Since the clock are already prepared since probe() and unprepared in
remove(), use simple clk_enable()/clk_disable() calls to enable and
disable the clock on runtime suspend and resume, to avoid hitting the
prepare_lock mutex.
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Fixes: 4e7bca6fc0 ("i2c: i2c-stm32f7: add PM Runtime support")
Cc: <stable@vger.kernel.org> # v5.0+
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1d4a1adbed2582444aaf97671858b7d12915bd05 ]
In the event that the I2C bus was powered down when the I2C controller
driver loads, or some spurious pulses occur on the I2C bus, it's
possible that the controller detects a spurious I2C "start" condition.
In this situation it may continue to report the bus is busy indefinitely
and block the controller from working.
The "single-master" DT flag can be specified to disable bus busy checks
entirely, but this may not be safe to use in situations where other I2C
masters may potentially exist.
In the event that the controller reports "bus busy" for too long when
starting a transaction, we can try reinitializing the controller to see
if the busy condition clears. This allows recovering from this scenario.
Fixes: e1d5b6598c ("i2c: Add support for Xilinx XPS IIC Bus Interface")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Cc: <stable@vger.kernel.org> # v2.6.34+
Reviewed-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee1691d0ae103ba7fd9439800ef454674fadad27 ]
xiic_start_xfer can fail for different reasons:
- EBUSY: bus is busy or i2c messages still in tx_msg or rx_msg
- ETIMEDOUT: timed-out trying to clear the RX fifo
- EINVAL: wrong clock settings
Both EINVAL and ETIMEDOUT will currently print a specific error
message followed by a generic one, for example:
Failed to clear rx fifo
Error xiic_start_xfer
however EBUSY will simply output the generic message:
Error xiic_start_xfer
which is not really helpful.
This commit adds a new error message when a busy condition is detected
and also removes the generic message since it does not provide any
relevant information to the user.
Signed-off-by: Marc Ferland <marc.ferland@sonatest.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Stable-dep-of: 1d4a1adbed25 ("i2c: xiic: Try re-initialization on bus busy timeout")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1db4da55070d6a2754efeb3743f5312fc32f5961 upstream.
In accordance with the existing comment and code analysis
it is quite likely that there is a missed 'else' when adapter
times out. Add it.
Fixes: 5bc1200852 ("i2c: Add Intel SCH SMBus support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: <stable@vger.kernel.org> # v2.6.27+
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93701d3b84ac5f3ea07259d4ced405c53d757985 upstream.
When the i2c bus recovery occurs, driver will send i2c stop command
in the scl low condition. In this case the sw state will still keep
original situation. Under multi-master usage, i2c bus recovery will
be called when i2c transfer timeout occurs. Update the stop command
calling with aspeed_i2c_do_stop function to update master_state.
Fixes: f327c686d3 ("i2c: aspeed: added driver for Aspeed I2C")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Tommy Huang <tommy_huang@aspeedtech.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 470a662688563d8f5e0fb164930d6f5507a883e4 upstream.
Add an atomic_xfer method to the driver so that it behaves correctly
when controlling a PMIC that is responsible for device shutdown.
The atomic_xfer method added is similar to the one from the i2c-mv64xxx
driver. When running an atomic_xfer a bool flag in the driver data is
set, the interrupt is not unmasked on transfer start, and the IRQ
handler is manually invoked while waiting for pending transfers to
complete.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7890fce6201aed46d3576e3d641f9ee5c1f0e16f ]
Value comes from DT, so it could be 0. Unlikely, but could be.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 14d069d92951a3e150c0a81f2ca3b93e54da913b upstream.
On ACPI machines, the tegra i2c module encounters an issue due to a
mutex being called inside a spinlock. This leads to the following bug:
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:585
...
Call trace:
__might_sleep
__mutex_lock_common
mutex_lock_nested
acpi_subsys_runtime_resume
rpm_resume
tegra_i2c_xfer
The problem arises because during __pm_runtime_resume(), the spinlock
&dev->power.lock is acquired before rpm_resume() is called. Later,
rpm_resume() invokes acpi_subsys_runtime_resume(), which relies on
mutexes, triggering the error.
To address this issue, devices on ACPI are now marked as not IRQ-safe,
considering the dependency of acpi_subsys_runtime_resume() on mutexes.
Fixes: bd2fdedbf2 ("i2c: tegra: Add the ACPI support")
Cc: <stable@vger.kernel.org> # v5.17+
Co-developed-by: Michael van der Westhuizen <rmikey@meta.com>
Signed-off-by: Michael van der Westhuizen <rmikey@meta.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f6c29f710c1ff2590109f83be3e212b86c01e0f3 ]
If a SMBus alert is received and the originating device is not found,
the reason may be that the address reported on the SMBus alert address
is corrupted, for example because multiple devices asserted alert and
do not correctly implement SMBus arbitration.
If this happens, call alert handlers on all devices connected to the
given I2C bus, in the hope that this cleans up the situation.
This change reliably fixed the problem on a system with multiple devices
on a single bus. Example log where the device on address 0x18 (ADM1021)
and on address 0x4c (ADT7461A) both had the alert line asserted:
smbus_alert 3-000c: SMBALERT# from dev 0x0c, flag 0
smbus_alert 3-000c: no driver alert()!
smbus_alert 3-000c: SMBALERT# from dev 0x0c, flag 0
smbus_alert 3-000c: no driver alert()!
lm90 3-0018: temp1 out of range, please check!
lm90 3-0018: Disabling ALERT#
lm90 3-0029: Everything OK
lm90 3-002a: Everything OK
lm90 3-004c: temp1 out of range, please check!
lm90 3-004c: temp2 out of range, please check!
lm90 3-004c: Disabling ALERT#
Fixes: b5527a7766 ("i2c: Add SMBus alert support")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[wsa: fixed a typo in the commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37c526f00bc1c4f847fc800085f8f009d2e11be6 ]
The following messages were observed while testing alert functionality
on systems with multiple I2C devices on a single bus if alert was active
on more than one chip.
smbus_alert 3-000c: SMBALERT# from dev 0x0c, flag 0
smbus_alert 3-000c: no driver alert()!
and:
smbus_alert 3-000c: SMBALERT# from dev 0x28, flag 0
Once it starts, this message repeats forever at high rate. There is no
device at any of the reported addresses.
Analysis shows that this is seen if multiple devices have the alert pin
active. Apparently some devices do not support SMBus arbitration correctly.
They keep sending address bits after detecting an address collision and
handle the collision not at all or too late.
Specifically, address 0x0c is seen with ADT7461A at address 0x4c and
ADM1021 at address 0x18 if alert is active on both chips. Address 0x28 is
seen with ADT7483 at address 0x2a and ADT7461 at address 0x4c if alert is
active on both chips.
Once the system is in bad state (alert is set by more than one chip),
it often only recovers by power cycling.
To reduce the impact of this problem, abort the endless loop in
smbus_alert() if the same address is read more than once and not
handled by a driver.
Fixes: b5527a7766 ("i2c: Add SMBus alert support")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[wsa: it also fixed an interrupt storm in one of my experiments]
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[wsa: rebased, moved a comment as well, improved the 'invalid' value]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fea6b5ebb71a2830b042e42de7ae255017ac3ce8 ]
We should allow RXDMA only if the reset was really successful, so clear
the flag after the reset call.
Fixes: 0e864b552b23 ("i2c: rcar: reset controller is mandatory for Gen3+")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 119736c7af442ab398dbb806865988c98ef60d46 ]
The to-be-fixed commit rightfully prevented that the registers will be
cleared. However, the index must be cleared. Otherwise a read message
will re-issue the last work. Fix it and add a comment describing the
situation.
Fixes: c422b6a63024 ("i2c: testunit: don't erase registers after STOP")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea5ea84c9d3570dc06e8fc5ee2273eaa584aa3ac ]
R-Car Gen3+ needs a reset before every controller transfer. That erases
configuration of a potentially in parallel running local target
instance. To avoid this disruption, avoid controller transfers if a
local target is running. Also, disable SMBusHostNotify because it
requires being a controller and local target at the same time.
Fixes: 3b770017b0 ("i2c: rcar: handle RXDMA HW behaviour on Gen3")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b523c46e81ebd621515ab47117f95de197dfcbf ]
So far, we treated Gen4 as Gen3. But we are soon adding FM+ as a Gen4
specific feature, so prepare the code for the new devtype.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: ea5ea84c9d35 ("i2c: rcar: ensure Gen3+ reset does not disturb local targets")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e864b552b2302e40b2277629ebac79544a5c433 ]
Initially, we only needed a reset controller to make sure RXDMA works at
least once per transfer. Meanwhile, documentation has been updated. It
now says that a reset has to be performed prior every transaction, even
if it is non-DMA. So, make the reset controller a requirement instead of
being optional. And bail out if resetting fails.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: ea5ea84c9d35 ("i2c: rcar: ensure Gen3+ reset does not disturb local targets")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd9f5348089b65612e5ca976e2ae22f005340331 ]
I2C core handles the local target for receiving HostNotify alerts. There
is no separate driver bound to that address. That means userspace can
access it if desired, leading to further complications if controllers
are not capable of reading their own local target. Bind the local target
to the dummy driver so it will be marked as "handled by the kernel" if
the HostNotify feature is used. That protects aginst userspace access
and prevents other drivers binding to it.
Fixes: 2a71593da3 ("i2c: smbus: add core function handling SMBus host-notify")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e36c0f20cb1c74c7bd7ea31ba432c1c4a989031 ]
When probing, the hardware is not brought into a known state. This may
be a problem when a hypervisor restarts Linux without resetting the
hardware, leaving an old state running. Make sure the hardware gets
initialized, especially interrupts should be cleared and disabled.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Closes: https://lore.kernel.org/r/20240702045535.2000393-1-dirk.behme@de.bosch.com
Fixes: 6ccbe60713 ("i2c: add Renesas R-Car I2C driver")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f63b94be6942ba82c55343e196bd09b53227618e ]
When del_timer_sync() is called in an interrupt context it throws a warning
because of potential deadlock. The timer is used only to exit from
wait_for_completion() after a timeout so replacing the call with
wait_for_completion_timeout() allows to remove the problematic timer and
its related functions altogether.
Fixes: 41561f28e7 ("i2c: New Philips PNX bus driver")
Signed-off-by: Piotr Wojtaszczyk <piotr.wojtaszczyk@timesys.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 355b1513b1e97b6cef84b786c6480325dfd3753d ]
Annotate this variable as __ro_after_init to protect it from being
overwritten later.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c116deafd1a5cc1e9739099eb32114e90623209c ]
When clearing registers on new write requests was added, the protection
for currently running commands was missed leading to concurrent access
to the testunit registers. Check the flag beforehand.
Fixes: b39ab96aa8 ("i2c: testunit: add support for block process calls")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c422b6a630240f706063e0ecbb894aa8491b1fa1 ]
STOP fallsthrough to WRITE_REQUESTED but this became problematic when
clearing the testunit registers was added to the latter. Actually, there
is no reason to clear the testunit state after STOP. Doing it when a new
WRITE_REQUESTED arrives is enough. So, no need to fallthrough, at all.
Fixes: b39ab96aa8 ("i2c: testunit: add support for block process calls")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5a72477273066b5b357801ab2d315ef14949d402 upstream.
Setting IACK bit when core is disabled does not clear the "Interrupt Flag"
bit in the status register, and the interrupt remains pending.
Sometimes it causes failure for the very first message transfer, that is
usually a device probe.
Hence, set IACK bit after core is enabled to clear pending interrupt.
Fixes: 18f98b1e31 ("[PATCH] i2c: New bus driver for the OpenCores I2C controller")
Signed-off-by: Grygorii Tertychnyi <grygorii.tertychnyi@leica-geosystems.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Cc: stable@vger.kernel.org
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cbf3fb5b29e99e3689d63a88c3cddbffa1b8de99 ]
When an I2C adapter acts only as a slave, it should not claim to
support I2C master capabilities.
Fixes: 5b6d721b26 ("i2c: designware: enable SLAVE in platform module")
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Luis Oliveira <lolivei@synopsys.com>
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Jan Dabros <jsd@semihalf.com>
Cc: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3f858bbf04dbac934ac279aaee05d49eb9910051 upstream.
There is an issue with ACPI overlay table removal specifically related
to I2C multiplexers.
Consider an ACPI SSDT Overlay that defines a PCA9548 I2C mux on an
existing I2C bus. When this table is loaded we see the creation of a
device for the overall PCA9548 chip and 8 further devices - one
i2c_adapter each for the mux channels. These are all bound to their
ACPI equivalents via an eventual invocation of acpi_bind_one().
When we unload the SSDT overlay we run into the problem. The ACPI
devices are deleted as normal via acpi_device_del_work_fn() and the
acpi_device_del_list.
However, the following warning and stack trace is output as the
deletion does not go smoothly:
------------[ cut here ]------------
kernfs: can not remove 'physical_node', no directory
WARNING: CPU: 1 PID: 11 at fs/kernfs/dir.c:1674 kernfs_remove_by_name_ns+0xb9/0xc0
Modules linked in:
CPU: 1 PID: 11 Comm: kworker/u128:0 Not tainted 6.8.0-rc6+ #1
Hardware name: congatec AG conga-B7E3/conga-B7E3, BIOS 5.13 05/16/2023
Workqueue: kacpi_hotplug acpi_device_del_work_fn
RIP: 0010:kernfs_remove_by_name_ns+0xb9/0xc0
Code: e4 00 48 89 ef e8 07 71 db ff 5b b8 fe ff ff ff 5d 41 5c 41 5d e9 a7 55 e4 00 0f 0b eb a6 48 c7 c7 f0 38 0d 9d e8 97 0a d5 ff <0f> 0b eb dc 0f 1f 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90
RSP: 0018:ffff9f864008fb28 EFLAGS: 00010286
RAX: 0000000000000000 RBX: ffff8ef90a8d4940 RCX: 0000000000000000
RDX: ffff8f000e267d10 RSI: ffff8f000e25c780 RDI: ffff8f000e25c780
RBP: ffff8ef9186f9870 R08: 0000000000013ffb R09: 00000000ffffbfff
R10: 00000000ffffbfff R11: ffff8f000e0a0000 R12: ffff9f864008fb50
R13: ffff8ef90c93dd60 R14: ffff8ef9010d0958 R15: ffff8ef9186f98c8
FS: 0000000000000000(0000) GS:ffff8f000e240000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f48f5253a08 CR3: 00000003cb82e000 CR4: 00000000003506f0
Call Trace:
<TASK>
? kernfs_remove_by_name_ns+0xb9/0xc0
? __warn+0x7c/0x130
? kernfs_remove_by_name_ns+0xb9/0xc0
? report_bug+0x171/0x1a0
? handle_bug+0x3c/0x70
? exc_invalid_op+0x17/0x70
? asm_exc_invalid_op+0x1a/0x20
? kernfs_remove_by_name_ns+0xb9/0xc0
? kernfs_remove_by_name_ns+0xb9/0xc0
acpi_unbind_one+0x108/0x180
device_del+0x18b/0x490
? srso_return_thunk+0x5/0x5f
? srso_return_thunk+0x5/0x5f
device_unregister+0xd/0x30
i2c_del_adapter.part.0+0x1bf/0x250
i2c_mux_del_adapters+0xa1/0xe0
i2c_device_remove+0x1e/0x80
device_release_driver_internal+0x19a/0x200
bus_remove_device+0xbf/0x100
device_del+0x157/0x490
? __pfx_device_match_fwnode+0x10/0x10
? srso_return_thunk+0x5/0x5f
device_unregister+0xd/0x30
i2c_acpi_notify+0x10f/0x140
notifier_call_chain+0x58/0xd0
blocking_notifier_call_chain+0x3a/0x60
acpi_device_del_work_fn+0x85/0x1d0
process_one_work+0x134/0x2f0
worker_thread+0x2f0/0x410
? __pfx_worker_thread+0x10/0x10
kthread+0xe3/0x110
? __pfx_kthread+0x10/0x10
ret_from_fork+0x2f/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
---[ end trace 0000000000000000 ]---
...
repeated 7 more times, 1 for each channel of the mux
...
The issue is that the binding of the ACPI devices to their peer I2C
adapters is not correctly cleaned up. Digging deeper into the issue we
see that the deletion order is such that the ACPI devices matching the
mux channel i2c adapters are deleted first during the SSDT overlay
removal. For each of the channels we see a call to i2c_acpi_notify()
with ACPI_RECONFIG_DEVICE_REMOVE but, because these devices are not
actually i2c_clients, nothing is done for them.
Later on, after each of the mux channels has been dealt with, we come
to delete the i2c_client representing the PCA9548 device. This is the
call stack we see above, whereby the kernel cleans up the i2c_client
including destruction of the mux and its channel adapters. At this
point we do attempt to unbind from the ACPI peers but those peers no
longer exist and so we hit the kernfs errors.
The fix is to augment i2c_acpi_notify() to handle i2c_adapters. But,
given that the life cycle of the adapters is linked to the i2c_client,
instead of deleting the i2c_adapters during the i2c_acpi_notify(), we
just trigger unbinding of the ACPI device from the adapter device, and
allow the clean up of the adapter to continue in the way it always has.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Fixes: 525e6fabea ("i2c / ACPI: add support for ACPI reconfigure notifications")
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 55750148e5595bb85605e8fbb40b2759c2c4c2d7 ]
If an error occurs after the clk_prepare_enable() call, it should be undone
by a corresponding clk_disable_unprepare() call, as already done in the
remove() function.
As devm_clk_get() is used, we can switch to devm_clk_get_enabled() to
handle it automatically and fix the probe.
Update the remove() function accordingly and remove the now useless
clk_disable_unprepare() call.
Fixes: 0d676a6c43 ("i2c: add support for Socionext SynQuacer I2C controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2e55b449de7298a751ed0256251019d302af453 ]
The Driver unintentionally programs ctrl reg to clear the fifo, which
happens after the start of transaction. Previously, this was not an issue
as it involved read-modified-write. However, this issue breaks i2c reads
on QEMU, as i2c-read is executed before guest starts programming control
register.
Fixes: ff0cf7bca6 ("i2c: cadence: Remove unnecessary register reads")
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91811a31b68d3765b3065f4bb6d7d6d84a7cfc9f ]
Baruch reported an OOPS when using the designware controller as target
only. Target-only modes break the assumption of one transfer function
always being available. Fix this by always checking the pointer in
__i2c_transfer.
Reported-by: Baruch Siach <baruch@tkos.co.il>
Closes: https://lore.kernel.org/r/4269631780e5ba789cf1ae391eec1b959def7d99.1712761976.git.baruch@tkos.co.il
Fixes: 4b1acc4333 ("i2c: core changes for slave support")
[wsa: dropped the simplification in core-smbus to avoid theoretical regressions]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c94612a72ac87b0337a0d85b9263266776ed4190 ]
I believe RX FIFO depth define 0 is incorrect on Wangxun 10Gb NIC. It
must be at least 1 since code is able to read received data from the
DW_IC_DATA_CMD register.
For now this define is irrelevant since the txgbe_i2c_dw_xfer_quirk()
doesn't use the rx_fifo_depth member variable of struct dw_i2c_dev but
is needed when converting code into generic polling mode implementation.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ceb013b2d9a2946035de5e1827624edc85ae9484 upstream.
If registering the platform device fails, the lookup table is
removed in the error path. On module removal we would try to
remove the lookup table again. Fix this by setting priv->lookup
only if registering the platform device was successful.
In addition free the memory allocated for the lookup table in
the error path.
Fixes: d308dfbf62 ("i2c: mux/i801: Switch to use descriptor passing")
Cc: stable@vger.kernel.org
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 87aec499368d488c20292952d6d4be7cb9e49c5e ]
When being a target, NAK from the controller means that all bytes have
been transferred. So, the last byte needs also to be marked as
'processed'. Otherwise index registers of backends may not increase.
Fixes: f7414cd692 ("i2c: imx: support slave mode for imx I2C driver")
Signed-off-by: Corey Minyard <minyard@acm.org>
Tested-by: Andrew Manley <andrew.manley@sealingtech.com>
Reviewed-by: Andrew Manley <andrew.manley@sealingtech.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
[wsa: fixed comment and commit message to properly describe the case]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1c9d0f6f7f1dbf29db996bd8e166242843a5f21 ]
According to the Intel datasheets, software must reset the block
buffer index twice for block process call transactions: once before
writing the outgoing data to the buffer, and once again before
reading the incoming data from the buffer.
The driver is currently missing the second reset, causing the wrong
portion of the block buffer to be read.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reported-by: Piotr Zakowski <piotr.zakowski@intel.com>
Closes: https://lore.kernel.org/linux-i2c/20240213120553.7b0ab120@endymion.delvare/
Fixes: 315cd67c94 ("i2c: i801: Add Block Write-Block Read Process Call support")
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f44bff19268517ee98e80e944cad0f04f1db72e3 ]
On powerpc, it is possible to compile test both the new apple (arm) and
old pasemi (powerpc) drivers for the i2c hardware at the same time,
which leads to a warning about linking the same object file twice:
scripts/Makefile.build:244: drivers/i2c/busses/Makefile: i2c-pasemi-core.o is added to multiple modules: i2c-apple i2c-pasemi
Rework the driver to have an explicit helper module, letting Kbuild
take care of whether this should be built-in or a loadable driver.
Fixes: 9bc5f4f660 ("i2c: pasemi: Split pci driver to its own file")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83ef106fa732aea8558253641cd98e8a895604d7 ]
For i2c read operation in GSI mode, we are getting timeout
due to malformed TRE basically incorrect TRE sequence
in gpi(drivers/dma/qcom/gpi.c) driver.
I2C driver has geni_i2c_gpi(I2C_WRITE) function which generates GO TRE and
geni_i2c_gpi(I2C_READ)generates DMA TRE. Hence to generate GO TRE before
DMA TRE, we should move geni_i2c_gpi(I2C_WRITE) before
geni_i2c_gpi(I2C_READ) inside the I2C GSI mode transfer function
i.e. geni_i2c_gpi_xfer().
TRE stands for Transfer Ring Element - which is basically an element with
size of 4 words. It contains all information like slave address,
clk divider, dma address value data size etc).
Mainly we have 3 TREs(Config, GO and DMA tre).
- CONFIG TRE : consists of internal register configuration which is
required before start of the transfer.
- DMA TRE : contains DDR/Memory address, called as DMA descriptor.
- GO TRE : contains Transfer directions, slave ID, Delay flags, Length
of the transfer.
I2c driver calls GPI driver API to config each TRE depending on the
protocol.
For read operation tre sequence will be as below which is not aligned
to hardware programming guide.
- CONFIG tre
- DMA tre
- GO tre
As per Qualcomm's internal Hardware Programming Guide, we should configure
TREs in below sequence for any RX only transfer.
- CONFIG tre
- GO tre
- DMA tre
Fixes: d8703554f4 ("i2c: qcom-geni: Add support for GPI DMA")
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # qrb5165-rb5
Co-developed-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Signed-off-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Signed-off-by: Viken Dadhaniya <quic_vdadhani@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92a85b7c6262f19c65a1c115cf15f411ba65a57c ]
Rockchip RV1126 is using old style i2c controller, the i2c2
bus uses a non-sequential offset in the grf register for the
mask/value bits for this bus.
This patch fixes i2c2 bus on rv1126 SoCs.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 990489e1042c6c5d6bccf56deca68f8dbeed8180 ]
To properly handle ACK on the bus when transferring more than one
message in polling mode, move the polling handling loop from
s3c24xx_i2c_message_start() to s3c24xx_i2c_doxfer(). This way
i2c_s3c_irq_nextbyte() is always executed till the end, properly
acknowledging the IRQ bits and no recursive calls to
i2c_s3c_irq_nextbyte() are made.
While touching this, also fix finishing transfers in polling mode by
using common code path and always waiting for the bus to become idle
and disabled.
Fixes: 117053f77a ("i2c: s3c2410: Add polling mode support")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d9cf23ed55d7ba3ab26d617a3ae507863674c8f ]
To properly handle read transfers in polling mode, no waiting for the ACK
state is needed as it will never come. Just wait a bit to ensure start
state is on the bus and continue processing next bytes.
Fixes: 117053f77a ("i2c: s3c2410: Add polling mode support")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19cde9c92b8d3b7ee555d0da3bcb0232d3a784f4 ]
Possible deadlock scenario (on reboot):
rk3x_i2c_xfer_common(polling)
-> rk3x_i2c_wait_xfer_poll()
-> rk3x_i2c_irq(0, i2c);
--> spin_lock(&i2c->lock);
...
<rk3x i2c interrupt>
-> rk3x_i2c_irq(0, i2c);
--> spin_lock(&i2c->lock); (deadlock here)
Store the IRQ number and disable/enable it around the polling transfer.
This patch has been tested on NanoPC-T4.
Signed-off-by: Jensen Huang <jensenhuang@friendlyarm.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a3368e1186e3ce8e38f78cbca019622095b1f331 upstream.
Since commit aa49c90894d0 ("i2c: core: Run atomic i2c xfer when
!preemptible"), the whole reboot/power off sequence on non-preempt kernels
is using atomic i2c xfer, as !preemptible() always results to 1.
During device_shutdown(), the i2c might be used a lot and not all busses
have implemented an atomic xfer handler. This results in a lot of
avoidable noise, like:
[ 12.687169] No atomic I2C transfer handler for 'i2c-0'
[ 12.692313] WARNING: CPU: 6 PID: 275 at drivers/i2c/i2c-core.h:40 i2c_smbus_xfer+0x100/0x118
...
Fix this by allowing non-atomic xfer when the interrupts are enabled, as
it was before.
Link: https://lore.kernel.org/r/20231222230106.73f030a5@yea
Link: https://lore.kernel.org/r/20240102150350.3180741-1-mwalle@kernel.org
Link: https://lore.kernel.org/linux-i2c/13271b9b-4132-46ef-abf8-2c311967bb46@mailbox.org/
Fixes: aa49c90894d0 ("i2c: core: Run atomic i2c xfer when !preemptible")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Benjamin Bara <benjamin.bara@skidata.com>
Tested-by: Michael Walle <mwalle@kernel.org>
Tested-by: Tor Vic <torvic9@mailbox.org>
[wsa: removed a comment which needs more work, code is ok]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b4cc1cbba5195a4dd497cf2f8f09e7807977d543 ]
Some masters may drive the transfers with low enough latency between
the nak/stop phase of the current command and the start/address phase
of the following command that the interrupts are coalesced by the
time we process them.
Handle the stop conditions before processing SLAVE_MATCH to fix the
complaints that sometimes occur below.
"aspeed-i2c-bus 1e78a040.i2c-bus: irq handled != irq. Expected
0x00000086, but was 0x00000084"
Fixes: f9eb91350b ("i2c: aspeed: added slave support for Aspeed I2C driver")
Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 382561d16854a747e6df71034da08d20d6013dfe ]
When an I2C device contains a wake IRQ subordinate to a regmap-irq chip,
the regmap-irq code must be able to perform I2C transactions during
suspend_device_irqs() and resume_device_irqs(). Therefore, the bus must
be suspended/resumed during the NOIRQ phase.
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Kimriver Liu