Mediadetect is another name for the EDPD (energy detect power down).
This feature allows device to save extra power when no link is available.
PHY goes into the extreme power saving mode and only periodically wakes up
and checks for the link.
AQC devices has fixed check period of 6 seconds
The feature may increase linkup time.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY downshift allows phy to try renegotiate if link is unstable
and can carry higher speed.
AQC devices has integrated PHY which is controlled by MAC firmware.
Thus, driver defines new ethtool callbacks to implement phy tunables
via netdev.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the possibility to obtain MAC temperature via hwmon.
On A1 there are two separate temperature sensors.
On A2 there's only one temperature sensor, which is used for reporting
both MAC and PHY temperature.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for 64-bit reads/writes where applicable, e.g.
A2 supports them.
Signed-off-by: Pavel Belous <pbelous@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves FRAC_PER_NS to aq_hw.h so that it can be used in both
hw_atl (A1) and hw_atl2 (A2) in the future.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch disables PTP on AQC111 and AQC112 due to a known HW issue,
which can cause datapath issues.
Ideally PTP block should have been disabled via PHY provisioning, but
unfortunately many units have been shipped with enabled PTP block.
Thus, we have to work around this in the driver.
Fixes: dbcd6806af ("net: aquantia: add support for Phy access")
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds link partner capabilities reporting support on A2.
In particular, the following capabilities are available for reporting:
* link rate;
* EEE;
* flow control.
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for 10M/100M/1G half duplex rates, which are
supported by A2 in additional to full duplex rates supported by A1.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for mqprio min_rate limiters.
A2 HW supports Weighted Strict Priority (WSP) arbitration for Tx Descriptor
Queue scheduling among TCs, which can be used for min_rate shaping.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds initial support for mqprio rate limiters (max_rate only).
Atlantic HW supports Rate-Shaping for time-sensitive traffic at per
Traffic Class (TC) granularity.
Target rate is defined by:
* nominal link rate (always 10G);
* rate factor (ratio between nominal rate and max allowed).
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds multi-TC support.
PTP is automatically disabled when the user enables more than 2 TCs,
otherwise traffic on TC2 won't quite work, because it's reserved for PTP.
Signed-off-by: Dmitry Bezrukov <dbezrukov@marvell.com>
Co-developed-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Co-developed-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains the following changes:
* add cfg->is_ptp (used for PTP enable/disable switch, which
is described in more details below);
* add cfg->tc_mode (A1 supports 2 HW modes only);
* setup queue to TC mapping based on TC mode on A2;
* remove hw_tx_tc_mode_get / hw_rx_tc_mode_get hw_ops.
In the first generation of our hardware (A1), a whole traffic class is
consumed for PTP handling in FW (FW uses it to send the ptp data and to
send back timestamps).
The 'is_ptp' flag introduced in this patch will be used in to automatically
disable PTP when a conflicting configuration is detected, e.g. when
multiple TCs are enabled.
Signed-off-by: Dmitry Bezrukov <dbezrukov@marvell.com>
Co-developed-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains the following changes:
* access cfg via aq_nic_get_cfg() in aq_nic_start() and aq_nic_map_skb();
* call aq_nic_get_dev() just once in aq_nic_map_skb();
* move ring allocation/deallocation out of aq_vec_alloc()/aq_vec_free();
* add the missing aq_nic_deinit() in atl_resume_common();
* rename 'tcs' field to 'tcs_max' in aq_hw_caps_s to differentiate it from
the 'tcs' field in aq_nic_cfg_s, which is used for the current number of
TCs;
* update _TC_MAX defines to the actual number of supported TCs;
* move tx_tc_mode register defines slightly higher (just to keep the order
of definitions);
* separate variables for TX/RX buff_size in hw_atl*_hw_qos_set();
* use AQ_HW_*_TC instead of hardcoded magic numbers;
* actually use the 'ret' value in aq_mdo_add_secy();
Signed-off-by: Dmitry Bezrukov <dbezrukov@marvell.com>
Co-developed-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds basic hw_ops layout for A2.
Actual implementation will be added in the follow-up patches.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the bare minimum of A2 HW bindings required to
get fw_ops working.
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IS_CHIP feature will be used to differentiate between A1 and A2,
where necessary. Thus, move it to aq_hw.h, rename it and make
it accept the 'hw' pointer.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hw_get_fw_version() never fails, so this patch simplifies its
usage by utilizing return value instead of output argument.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A2 will have a different implementation of these 2 APIs, so
this patch moves them to hw_ops in preparation for A2.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Co-developed-by: Dmitry Bezrukov <dbezrukov@marvell.com>
Signed-off-by: Dmitry Bezrukov <dbezrukov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds basic functionality for MACSec offloading for Atlantic
NICs.
MACSec offloading functionality is enabled if network card has
appropriate FW that has MACSec offloading enabled in config.
Actual functionality (ingress, egress, etc) will be added in follow-up
patches.
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clock adjustment data should be passed to FW as well, otherwise in some
cases a drift was observed when using GPIO features.
Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here we add a number of ethtool private flags
to allow enabling various loopbacks on HW.
Thats useful for verification and bringup works.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device FW has a separate memory area where various
config fields are stored and could be used by the
driver.
Here we modify download/upload infrastructure to
allow accessing this area.
Lateron this will be used to configure various behaviours
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
`ethtool -p eth0` will blink leds helping identify
physical port.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on FW configuration we can manage from 0 to 3 PINs for periodic output
and from 0 to 1 ext ts PIN for getting TS for external event.
Ext TS PIN functionality is implemented via periodic timestamps polling
directly from PHY, because right now there is now way to receive the
PIN trigger interrupt from phy.
The polling interval is 15 milliseconds.
Co-developed-by: Egor Pomozov <epomozov@marvell.com>
Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Co-developed-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GPIO PIN control and access is done by direct phy manipulation.
Here we add an aq_phy module which is able to access phy registers
via MDIO access mailbox.
Access is controlled via HW semaphore.
Co-developed-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here we do alloc/free IRQs for PTP rings.
We also implement processing of PTP packets on TX and RX sides.
Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Co-developed-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Co-developed-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add implementations of PTP rings alloc/free.
PTP desing on this device uses two separate rings on a separate traffic
class for traffic rx/tx.
Third ring (hwts) is not a traffic ring, but is used only to receive timestamps
of the transmitted packets.
Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Co-developed-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Co-developed-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basic HW functions implemented for adjusting frequency,
adjusting time, getting and setting time.
With these callbacks we now do register ptp clock in the system.
Firmware interface parts are defined for PTP requests and interactions.
Enable/disable PTP counters in HW on clock register/unregister.
Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Co-developed-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Co-developed-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 101 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190113.822954939@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Declare macroes and nic fields to support link interrupt
handling
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ability to read the chip temperature from memory
via hwmon interface
Signed-off-by: Yana Esina <yana.esina@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since it uses the same NIC table as rx flow vlan filter therefore
rx-flow vlan filter accepts only vlans that present on the interface
in case of rx-vlan-filter is on.
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L2 EtherType filters allows to filter packet by EtherType field or
both EtherType and User Priority (PCP) field of 802.1Q.
UserPriority (vlan) parameter must be accompanied by mask 0x1FFF. That
is to distinguish VLAN filter from L2 Ethertype filter with
UserPriority since both User Priority and VLAN ID are passed in the
same 'vlan' parameter.
Example:
To add a filter that directs IP4 packess of priority 3 to queue 3:
ethtool -N <ethX> flow-type ether proto 0x800 vlan 0x600 m 0x1FFF \
action 3 loc 16
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VLAN filter (VLAN id) is compared against 16 filters.
VLAN id must be accompanied by mask 0xF000. That is to distinguish
VLAN filter from L2 Ethertype filter with UserPriority since both
User Priority and VLAN ID are passed in the same 'vlan' parameter.
Flow type may be any as it is not matched for VLAN filter.
Due to fixed order of the rules in the NIC, the location 0-15 are
reserved for vlan filters.
Example:
To add a rule that directs packets from VLAN 2001 to queue 5:
ethtool -N <ethX> flow-type ip4 vlan 2001 m 0xF000 action 5 loc 0
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support of L3/L4 5-tuple {protocol, src-ip, dst-ip, src-port, dst-port}
filters. Mask is not supported. Src-port and dst-port are only compared for
TCP/UDP/SCTP packets. Both IPv4 and IPv6 are supported.
The supported actions are the drop and the queue assignment.
Due to fixed order of the rules in the NIC, the location 32-39 are
reserved for L3/L4 5-tuple filters. The locations 32 and 36 are
reserved for IPv6 filters.
Examples:
sudo ethtool -N eth0 flow-type ip6 src-ip 2001:db8:0:f101::2 \
dst-ip 2001:db8:0:f101::5 action -1 loc 36
sudo ethtool -N eth0 flow-type udp4 src-ip 10.0.0.4 \
dst-ip 10.0.0.7 src-port 2000 dst-port 2001 action 2 loc 32
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX Checksum offloads could not be configured and ignored netdev features
flag for checksumming.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow control statuses were not synchronized between blocks,
that caused packets/link drop on some corner cases, when
MAC sent PFC although Phy was not expecting these to come.
Driver should readout the negotiated FC from phy and
configure RX block accordigly.
This is done on each link change event with information from FW.
Fixes: 288551de45 ("net: aquantia: Implement rx/tx flow control ethtools callback")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed extra characters from the names of structures to unify prefixes
used through the driver code (we normally use hw_atl for hw specifics).
HW_ATL_B0_ and HW_ATL_A0_ are the same and useless copies.
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support of Energy-Efficient Ethernet to aQuantia NIC's via ethtool
(according to the IEEE 802.3az specifications)
Signed-off-by: Yana Esina <yana.esina@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add WOL support. Currently only magic packet
(ethtool -s <ethX> wol g) feature is implemented.
Remove hw_set_power and move that to FW_OPS set_power:
because WOL configuration behaves differently on 1x and 2x
firmwares
Signed-off-by: Yana Esina <yana.esina@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting up macvlan/macvtap networks over atlantic NIC results
in no traffic over these networks because ndo_set_rx_mode did
not listed UC MACs as registered in unicast filter.
Here we fix that taking into account maximum number of UC
filters supported by hardware. If more than MAX addresses were
registered, we just enable promisc and/or allmulti to pass
the traffic in.
We also remove MULTICAST_ADDRESS_MAX constant from aq_cfg since
thats not a configurable parameter at all.
Fixes: b21f502 ("net:ethernet:aquantia: Fix for multicast filter handling.")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds ethtool -r|--negotiate operation support. It triggers special
control bit on FW interface causing FW to restart link negotiation.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Anton Mikaev <amikaev@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now pass link drop status to FW on init/deinit. This is required
to inform FW that driver took/released a control on link.
FW then will manage its own state and device power profile based
on this information. To improve management we remove mpi_set
function which ambiguously took both state and speed parameters.
Deinit callback is now a part of FW ops, as it actually manages the FW.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implemented ring size setup, min/max validation and reconfiguration in
runtime.
Signed-off-by: Anton Mikaev <amikaev@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The detailed reset sequence ensures all HW components are in aligned
state before NIC startup. It also supports cards with signed firmware (RBL)
and checks if their FW is valid.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This defines fw2x operations table and corresponding methods.
Some of the functions are being shared with 1.x firmware
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New AQC cards will have an updated firmware with new binary interface.
This patch extracts firmware specific operations into a separate table
and prepares for the introduction of new fw 2.x and 3.x
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address to check if HW is not dead/hang could be stored in
capabilities, since it is a constant. Change its name to better reflect
the idea.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh