The following BUG was reported by kasan:
BUG: KASAN: use-after-free in ipoib_cm_tx_start+0x430/0x1390 [ib_ipoib]
Read of size 80 at addr ffff88034c30bcd0 by task kworker/u16:1/24020
Workqueue: ipoib_wq ipoib_cm_tx_start [ib_ipoib]
Call Trace:
dump_stack+0x9a/0xeb
print_address_description+0xe3/0x2e0
kasan_report+0x18a/0x2e0
? ipoib_cm_tx_start+0x430/0x1390 [ib_ipoib]
memcpy+0x1f/0x50
ipoib_cm_tx_start+0x430/0x1390 [ib_ipoib]
? kvm_clock_read+0x1f/0x30
? ipoib_cm_skb_reap+0x610/0x610 [ib_ipoib]
? __lock_is_held+0xc2/0x170
? process_one_work+0x880/0x1960
? process_one_work+0x912/0x1960
process_one_work+0x912/0x1960
? wq_pool_ids_show+0x310/0x310
? lock_acquire+0x145/0x440
worker_thread+0x87/0xbb0
? process_one_work+0x1960/0x1960
kthread+0x314/0x3d0
? kthread_create_worker_on_cpu+0xc0/0xc0
ret_from_fork+0x3a/0x50
Allocated by task 0:
kasan_kmalloc+0xa0/0xd0
kmem_cache_alloc_trace+0x168/0x3e0
path_rec_create+0xa2/0x1f0 [ib_ipoib]
ipoib_start_xmit+0xa98/0x19e0 [ib_ipoib]
dev_hard_start_xmit+0x159/0x8d0
sch_direct_xmit+0x226/0xb40
__dev_queue_xmit+0x1d63/0x2950
neigh_update+0x889/0x1770
arp_process+0xc47/0x21f0
arp_rcv+0x462/0x760
__netif_receive_skb_core+0x1546/0x2da0
netif_receive_skb_internal+0xf2/0x590
napi_gro_receive+0x28e/0x390
ipoib_ib_handle_rx_wc_rss+0x873/0x1b60 [ib_ipoib]
ipoib_rx_poll_rss+0x17d/0x320 [ib_ipoib]
net_rx_action+0x427/0xe30
__do_softirq+0x28e/0xc42
Freed by task 26680:
__kasan_slab_free+0x11d/0x160
kfree+0xf5/0x360
ipoib_flush_paths+0x532/0x9d0 [ib_ipoib]
ipoib_set_mode_rss+0x1ad/0x560 [ib_ipoib]
set_mode+0xc8/0x150 [ib_ipoib]
kernfs_fop_write+0x279/0x440
__vfs_write+0xd8/0x5c0
vfs_write+0x15e/0x470
ksys_write+0xb8/0x180
do_syscall_64+0x9b/0x420
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The buggy address belongs to the object at ffff88034c30bcc8
which belongs to the cache kmalloc-512 of size 512
The buggy address is located 8 bytes inside of
512-byte region [ffff88034c30bcc8, ffff88034c30bec8)
The buggy address belongs to the page:
The following race between change mode and xmit flow is the reason for
this use-after-free:
Change mode Send packet 1 to GID XX Send packet 2 to GID XX
| | |
start | |
| | |
| | |
| Create new path for GID XX |
| and update neigh path |
| | |
| | |
| | |
flush_paths | |
| |
queue_work(cm.start_task) |
| Path for GID XX not found
| create new path
|
|
start_task runs with old
released path
There is no locking to protect the lifetime of the path through the
ipoib_cm_tx struct, so delete it entirely and always use the newly looked
up path under the priv->lock.
Fixes: 546481c281 ("IB/ipoib: Fix memory corruption in ipoib cm mode connect flow")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Drop LIST_HEAD where the variable it declares is never used.
Commit 31c02e2157 ("IPoIB: Avoid using stale last_send counter
when reaping AHs") removed the uses, but not the declaration.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier x;
@@
- LIST_HEAD(x);
... when != x
// </smpl>
Fixes: 31c02e2157 ("IPoIB: Avoid using stale last_send counter when reaping AHs")
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This has been a fairly typical cycle, with the usual sorts of driver
updates. Several series continue to come through which improve and
modernize various parts of the core code, and we finally are starting to
get the uAPI command interface cleaned up.
- Various driver fixes for bnxt_re, cxgb3/4, hfi1, hns, i40iw, mlx4, mlx5,
qib, rxe, usnic
- Rework the entire syscall flow for uverbs to be able to run over
ioctl(). Finally getting past the historic bad choice to use write()
for command execution
- More functional coverage with the mlx5 'devx' user API
- Start of the HFI1 series for 'TID RDMA'
- SRQ support in the hns driver
- Support for new IBTA defined 2x lane widths
- A big series to consolidate all the driver function pointers into
a big struct and have drivers provide a 'static const' version of the
struct instead of open coding initialization
- New 'advise_mr' uAPI to control device caching/loading of page tables
- Support for inline data in SRPT
- Modernize how umad uses the driver core and creates cdev's and sysfs
files
- First steps toward removing 'uobject' from the view of the drivers
-----BEGIN PGP SIGNATURE-----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=T0p1
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"This has been a fairly typical cycle, with the usual sorts of driver
updates. Several series continue to come through which improve and
modernize various parts of the core code, and we finally are starting
to get the uAPI command interface cleaned up.
- Various driver fixes for bnxt_re, cxgb3/4, hfi1, hns, i40iw, mlx4,
mlx5, qib, rxe, usnic
- Rework the entire syscall flow for uverbs to be able to run over
ioctl(). Finally getting past the historic bad choice to use
write() for command execution
- More functional coverage with the mlx5 'devx' user API
- Start of the HFI1 series for 'TID RDMA'
- SRQ support in the hns driver
- Support for new IBTA defined 2x lane widths
- A big series to consolidate all the driver function pointers into a
big struct and have drivers provide a 'static const' version of the
struct instead of open coding initialization
- New 'advise_mr' uAPI to control device caching/loading of page
tables
- Support for inline data in SRPT
- Modernize how umad uses the driver core and creates cdev's and
sysfs files
- First steps toward removing 'uobject' from the view of the drivers"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (193 commits)
RDMA/srpt: Use kmem_cache_free() instead of kfree()
RDMA/mlx5: Signedness bug in UVERBS_HANDLER()
IB/uverbs: Signedness bug in UVERBS_HANDLER()
IB/mlx5: Allocate the per-port Q counter shared when DEVX is supported
IB/umad: Start using dev_groups of class
IB/umad: Use class_groups and let core create class file
IB/umad: Refactor code to use cdev_device_add()
IB/umad: Avoid destroying device while it is accessed
IB/umad: Simplify and avoid dynamic allocation of class
IB/mlx5: Fix wrong error unwind
IB/mlx4: Remove set but not used variable 'pd'
RDMA/iwcm: Don't copy past the end of dev_name() string
IB/mlx5: Fix long EEH recover time with NVMe offloads
IB/mlx5: Simplify netdev unbinding
IB/core: Move query port to ioctl
RDMA/nldev: Expose port_cap_flags2
IB/core: uverbs copy to struct or zero helper
IB/rxe: Reuse code which sets port state
IB/rxe: Make counters thread safe
IB/mlx5: Use the correct commands for UMEM and UCTX allocation
...
Introduce a 'flags' field to destroy address handle callback and add a
flag that marks whether the callback is executed in an atomic context or
not.
This will allow drivers to wait for completion instead of polling for it
when it is allowed.
Signed-off-by: Gal Pressman <galpress@amazon.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Introduce a 'flags' field to create address handle callback and add a flag
that marks whether the callback is executed in an atomic context or not.
This will allow drivers to wait for completion instead of polling for it
when it is allowed.
Signed-off-by: Gal Pressman <galpress@amazon.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Make all the required change to start use the ib_device_ops structure.
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
In order to pass extack together with NETDEV_PRE_UP notifications, it's
necessary to route the extack to __dev_open() from diverse (possibly
indirect) callers. One prominent API through which the notification is
invoked is dev_change_flags().
Therefore extend dev_change_flags() with and extra extack argument and
update all users. Most of the calls end up just encoding NULL, but
several sites (VLAN, ipvlan, VRF, rtnetlink) do have extack available.
Since the function declaration line is changed anyway, name the other
function arguments to placate checkpatch.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This has been a smaller cycle with many of the commits being smallish code
fixes and improvements across the drivers.
- Driver updates for bnxt_re, cxgb4, hfi1, hns, mlx5, nes, qedr, and rxe
- Memory window support in hns
- mlx5 user API 'flow mutate/steering' allows accessing the full packet
mangling and matching machinery from user space
- Support inter-working with verbs API calls in the 'devx' mlx5 user API, and
provide options to use devx with less privilege
- Modernize the use of syfs and the device interface to use attribute groups
and cdev properly for uverbs, and clean up some of the core code's device list
management
- More progress on net namespaces for RDMA devices
- Consolidate driver BAR mmapping support into core code helpers and rework
how RDMA holds poitners to mm_struct for get_user_pages cases
- First pass to use 'dev_name' instead of ib_device->name
- Device renaming for RDMA devices
-----BEGIN PGP SIGNATURE-----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=pacJ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"This has been a smaller cycle with many of the commits being smallish
code fixes and improvements across the drivers.
- Driver updates for bnxt_re, cxgb4, hfi1, hns, mlx5, nes, qedr, and
rxe
- Memory window support in hns
- mlx5 user API 'flow mutate/steering' allows accessing the full
packet mangling and matching machinery from user space
- Support inter-working with verbs API calls in the 'devx' mlx5 user
API, and provide options to use devx with less privilege
- Modernize the use of syfs and the device interface to use attribute
groups and cdev properly for uverbs, and clean up some of the core
code's device list management
- More progress on net namespaces for RDMA devices
- Consolidate driver BAR mmapping support into core code helpers and
rework how RDMA holds poitners to mm_struct for get_user_pages
cases
- First pass to use 'dev_name' instead of ib_device->name
- Device renaming for RDMA devices"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (242 commits)
IB/mlx5: Add support for extended atomic operations
RDMA/core: Fix comment for hw stats init for port == 0
RDMA/core: Refactor ib_register_device() function
RDMA/core: Fix unwinding flow in case of error to register device
ib_srp: Remove WARN_ON in srp_terminate_io()
IB/mlx5: Allow scatter to CQE without global signaled WRs
IB/mlx5: Verify that driver supports user flags
IB/mlx5: Support scatter to CQE for DC transport type
RDMA/drivers: Use core provided API for registering device attributes
RDMA/core: Allow existing drivers to set one sysfs group per device
IB/rxe: Remove unnecessary enum values
RDMA/umad: Use kernel API to allocate umad indexes
RDMA/uverbs: Use kernel API to allocate uverbs indexes
RDMA/core: Increase total number of RDMA ports across all devices
IB/mlx4: Add port and TID to MAD debug print
IB/mlx4: Enable debug print of SMPs
RDMA/core: Rename ports_parent to ports_kobj
RDMA/core: Do not expose unsupported counters
IB/mlx4: Refer to the device kobject instead of ports_parent
RDMA/nldev: Allow IB device rename through RDMA netlink
...
IPCB should be cleared before icmp_send, since it may contain data from
previous layers and the data could be misinterpreted as ip header options,
which later caused the ihl to be set to an invalid value and resulted in
the following stack corruption:
[ 1083.031512] ib0: packet len 57824 (> 2048) too long to send, dropping
[ 1083.031843] ib0: packet len 37904 (> 2048) too long to send, dropping
[ 1083.032004] ib0: packet len 4040 (> 2048) too long to send, dropping
[ 1083.032253] ib0: packet len 63800 (> 2048) too long to send, dropping
[ 1083.032481] ib0: packet len 23960 (> 2048) too long to send, dropping
[ 1083.033149] ib0: packet len 63800 (> 2048) too long to send, dropping
[ 1083.033439] ib0: packet len 63800 (> 2048) too long to send, dropping
[ 1083.033700] ib0: packet len 63800 (> 2048) too long to send, dropping
[ 1083.034124] ib0: packet len 63800 (> 2048) too long to send, dropping
[ 1083.034387] ==================================================================
[ 1083.034602] BUG: KASAN: stack-out-of-bounds in __ip_options_echo+0xf08/0x1310
[ 1083.034798] Write of size 4 at addr ffff880353457c5f by task kworker/u16:0/7
[ 1083.034990]
[ 1083.035104] CPU: 7 PID: 7 Comm: kworker/u16:0 Tainted: G O 4.19.0-rc5+ #1
[ 1083.035316] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu2 04/01/2014
[ 1083.035573] Workqueue: ipoib_wq ipoib_cm_skb_reap [ib_ipoib]
[ 1083.035750] Call Trace:
[ 1083.035888] dump_stack+0x9a/0xeb
[ 1083.036031] print_address_description+0xe3/0x2e0
[ 1083.036213] kasan_report+0x18a/0x2e0
[ 1083.036356] ? __ip_options_echo+0xf08/0x1310
[ 1083.036522] __ip_options_echo+0xf08/0x1310
[ 1083.036688] icmp_send+0x7b9/0x1cd0
[ 1083.036843] ? icmp_route_lookup.constprop.9+0x1070/0x1070
[ 1083.037018] ? netif_schedule_queue+0x5/0x200
[ 1083.037180] ? debug_show_all_locks+0x310/0x310
[ 1083.037341] ? rcu_dynticks_curr_cpu_in_eqs+0x85/0x120
[ 1083.037519] ? debug_locks_off+0x11/0x80
[ 1083.037673] ? debug_check_no_obj_freed+0x207/0x4c6
[ 1083.037841] ? check_flags.part.27+0x450/0x450
[ 1083.037995] ? debug_check_no_obj_freed+0xc3/0x4c6
[ 1083.038169] ? debug_locks_off+0x11/0x80
[ 1083.038318] ? skb_dequeue+0x10e/0x1a0
[ 1083.038476] ? ipoib_cm_skb_reap+0x2b5/0x650 [ib_ipoib]
[ 1083.038642] ? netif_schedule_queue+0xa8/0x200
[ 1083.038820] ? ipoib_cm_skb_reap+0x544/0x650 [ib_ipoib]
[ 1083.038996] ipoib_cm_skb_reap+0x544/0x650 [ib_ipoib]
[ 1083.039174] process_one_work+0x912/0x1830
[ 1083.039336] ? wq_pool_ids_show+0x310/0x310
[ 1083.039491] ? lock_acquire+0x145/0x3a0
[ 1083.042312] worker_thread+0x87/0xbb0
[ 1083.045099] ? process_one_work+0x1830/0x1830
[ 1083.047865] kthread+0x322/0x3e0
[ 1083.050624] ? kthread_create_worker_on_cpu+0xc0/0xc0
[ 1083.053354] ret_from_fork+0x3a/0x50
For instance __ip_options_echo is failing to proceed with invalid srr and
optlen passed from another layer via IPCB
[ 762.139568] IPv4: __ip_options_echo rr=0 ts=0 srr=43 cipso=0
[ 762.139720] IPv4: ip_options_build: IPCB 00000000f3cd969e opt 000000002ccb3533
[ 762.139838] IPv4: __ip_options_echo in srr: optlen 197 soffset 84
[ 762.139852] IPv4: ip_options_build srr=0 is_frag=0 rr_needaddr=0 ts_needaddr=0 ts_needtime=0 rr=0 ts=0
[ 762.140269] ==================================================================
[ 762.140713] IPv4: __ip_options_echo rr=0 ts=0 srr=0 cipso=0
[ 762.141078] BUG: KASAN: stack-out-of-bounds in __ip_options_echo+0x12ec/0x1680
[ 762.141087] Write of size 4 at addr ffff880353457c7f by task kworker/u16:0/7
Signed-off-by: Denis Drozdov <denisd@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
IPoIB netlink support was broken by the below commit since integrating
the rdma_netdev support relies on an allocation flow for netdevs that
was controlled by the ipoib driver while netdev's rtnl_newlink
implementation assumes that the netdev will be allocated by netlink.
Such situation leads to crash in __ipoib_device_add, once trying to
reuse netlink device.
This patch fixes the kernel oops for both mlx4 and mlx5
devices triggered by the following command:
Fixes: cd565b4b51 ("IB/IPoIB: Support acceleration options callbacks")
Signed-off-by: Denis Drozdov <denisd@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
netdev has several interfaces that expect to call alloc_netdev_mqs from
the core code, with the driver only providing the arguments. This is
incompatible with the rdma_netdev interface that returns the netdev
directly.
Thus re-organize the API used by ipoib so that the verbs core code calls
alloc_netdev_mqs for the driver. This is done by allowing the drivers to
provide the allocation parameters via a 'get_params' callback and then
initializing an allocated netdev as a second step.
Fixes: cd565b4b51 ("IB/IPoIB: Support acceleration options callbacks")
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Denis Drozdov <denisd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
These return the same thing but dev_name is a more conventional use of the
kernel API.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Some tools may currently be using only the deprecated attribute;
let's print an elaborate and clear deprecation notice to kmsg.
To do that, we have to replace the whole sysfs file, since we inherit
the original one from netdev.
Signed-off-by: Arseny Maslennikov <ar@cs.msu.ru>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Some InfiniBand network devices have multiple ports on the same PCI
function. This initializes the `dev_port' sysfs field of those
network interfaces with their port number.
Prior to this the kernel erroneously used the `dev_id' sysfs
field of those network interfaces to convey the port number to userspace.
The use of `dev_id' was considered correct until Linux 3.15,
when another field, `dev_port', was defined for this particular
purpose and `dev_id' was reserved for distinguishing stacked ifaces
(e.g: VLANs) with the same hardware address as their parent device.
Similar fixes to net/mlx4_en and many other drivers, which started
exporting this information through `dev_id' before 3.15, were accepted
into the kernel 4 years ago.
See 76a066f2a2 (`net/mlx4_en: Expose port number through sysfs').
Signed-off-by: Arseny Maslennikov <ar@cs.msu.ru>
Signed-off-by: Doug Ledford <dledford@redhat.com>
It is illegal to change MTU to a value lower than the minimum MTU
stated in ethernet spec. In addition to that we need to add 4 bytes
for encapsulation header (IPOIB_ENCAP_LEN).
Before "ifconfig ib0 mtu 0" command, succeeds while it obviously shouldn't.
Signed-off-by: Muhammad Sammar <muhammads@mellanox.com>
Reviewed-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Inside of start_xmit() the call to check if the connection is up and the
queueing of the packets for later transmission is not atomic which leaves
a window where cm_rep_handler can run, set the connection up, dequeue
pending packets and leave the subsequently queued packets by start_xmit()
sitting on neigh->queue until they're dropped when the connection is torn
down. This only applies to connected mode. These dropped packets can
really upset TCP, for example, and cause multi-minute delays in
transmission for open connections.
Here's the code in start_xmit where we check to see if the connection is
up:
if (ipoib_cm_get(neigh)) {
if (ipoib_cm_up(neigh)) {
ipoib_cm_send(dev, skb, ipoib_cm_get(neigh));
goto unref;
}
}
The race occurs if cm_rep_handler execution occurs after the above
connection check (specifically if it gets to the point where it acquires
priv->lock to dequeue pending skb's) but before the below code snippet in
start_xmit where packets are queued.
if (skb_queue_len(&neigh->queue) < IPOIB_MAX_PATH_REC_QUEUE) {
push_pseudo_header(skb, phdr->hwaddr);
spin_lock_irqsave(&priv->lock, flags);
__skb_queue_tail(&neigh->queue, skb);
spin_unlock_irqrestore(&priv->lock, flags);
} else {
++dev->stats.tx_dropped;
dev_kfree_skb_any(skb);
}
The patch acquires the netif tx lock in cm_rep_handler for the section
where it sets the connection up and dequeues and retransmits deferred
skb's.
Fixes: 839fcaba35 ("IPoIB: Connected mode experimental support")
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Knister <aaron.s.knister@nasa.gov>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Move all the checking for pkey and other validity to the __ipoib_vlan_add
function. This removes the last difference from the control flow
of the __ipoib_vlan_add to make the overall design simpler to
understand.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
This fixes a bug in the netlink path where the vlan_rwsem was not
held around __ipoib_vlan_add causing the child_intfs to be manipulated
unsafely.
In the process this greatly simplifies the vlan_rwsem write side locking
to only cover a single non-sleeping statement.
This also further increases the safety of the removal ordering by holding
the netdev of the parent while the child is active to ensure most bugs
become either an oops on a NULL priv or a deadlock on the netdev refcount.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Switching to priv_destructor and needs_free_netdev created a subtle
ordering problem in ipoib_remove_one.
Now that unregister_netdev frees the netdev and priv we must ensure that
the children are unregistered before trying to unregister the parent,
or child unregister will use after free.
The solution is to unregister the children, then parent, in the same batch
all while holding the rtnl_lock. This closes all the races where a new
child could have been added and ensures proper ordering.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
This mutex was introduced to deal with the deadlock formed by calling
unregister_netdev from within the sysfs callback of a netdev.
Now that we have priv_destructor and needs_free_netdev we can switch
to the more targeted solution of running the unregister from a
work queue. This avoids the deadlock and gets rid of the mutex.
The next patch in the series needs this mutex eliminated to create
atomicity of unregisteration.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Now that the unregister_netdev flow for IPoIB no longer relies on external
code we can now introduce the use of priv_destructor and
needs_free_netdev.
The rdma_netdev flow is switched to use the netdev common priv_destructor
instead of the special free_rdma_netdev and the IPOIB ULP adjusted:
- priv_destructor needs to switch to point to the ULP's destructor
which will then call the rdma_ndev's in the right order
- We need to be careful around the error unwind of register_netdev
as it sometimes calls priv_destructor on failure
- ULPs need to use ndo_init/uninit to ensure proper ordering
of failures around register_netdev
Switching to priv_destructor is a necessary pre-requisite to using
the rtnl new_link mechanism.
The VNIC user for rdma_netdev should also be revised, but that is left for
another patch.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Denis Drozdov <denisd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Now that we have a proper ndo_uninit, move code that naturally pairs
with the ndo_uninit into ndo_init. This allows the netdev core to natually
handle ordering.
This fixes the situation where register_netdev can fail before calling
ndo_init, in which case it wouldn't call ndo_uninit either.
Also move a bunch of duplicated init code that is shared between child
and parent for clarity. Now the child and parent register functions look
very similar.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Currently uninit is sometimes done twice in error flows, and is sprinkled
a bit all over the place.
Improve the clarity of the design by moving all uninit only into
ndo_uinit.
Some duplication is removed:
- Sometimes IPOIB_STOP_NEIGH_GC was done before unregister, but
this duplicates the process in ipoib_neigh_hash_init
- Flushing priv->wq was sometimes done before unregister,
but that duplicates what has been done in ndo_uninit
Uniniting the IB event queue must remain before unregister_netdev as it
requires the RTNL lock to be dropped, this is moved to a helper to make
that flow really clear and remove some duplication in error flows.
If register_netdev fails (and ndo_init is NULL) then it almost always
calls ndo_uninit, which lets us remove all the extra code from the error
unwinds. The next patch in the series will close the 'almost always' hole
by pairing a proper ndo_init with ndo_uninit.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
The neigh_reap_task is self restarting, but so long as we call
cancel_delayed_work_sync() it will be guaranteed to not be running and
never start again. Thus we don't need to have the racy
IPOIB_STOP_NEIGH_GC bit, or the confusing mismatch of places sometimes
calling flush_workqueue after the cancel.
This fixes a situation where the GC work could have been left running
in some rare situations.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This essentially duplicates the netdev's reg_state, so just use that
directly. The reg_state is updated under the rntl_lock, and all places
using GOING_DOWN already acquire the rtnl_lock so checking is safe.
Since the only place we use GOING_DOWN is for the parent device this
does not fix any bugs, but it is a step to tidy up the unregister flow
so that after later patches the flow is uniform and sane.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
The change of ipoib_ah data structure with adding "valid" flag and
checks of ah->valid in ipoib_start_xmit affected multicast packet flow.
Since the multicast flow doesn't invoke path_rec_start, "ah->valid" flag
remains unset, so that ipoib_start_xmit end up with neigh_refresh_path
instead of sending the packet using neigh.
"ah->valid" has to be set in multicast send flow. As a result IPoIB
starts sending packets via neigh immediately and eliminates 60sec delay
of neigh keep alive interval.
The typical example of this issue are two sequential arpings:
arping 11.134.208.9 -> got response (mcast_send)
arping 11.134.208.9 -> no response (ah->valid = 0)
Fixes: fa9391dbad ("RDMA/ipoib: Update paths on CLIENT_REREG/SM_CHANGE events")
Signed-off-by: Denis Drozdov <denisd@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The proper return code is "-EOPNOTSUPP" when the modify_cq() callback is
not supported, all drivers should generate this and all users should check
for it when detecting not supported functionality.
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com> (for mlx5)
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Constify several pointers such as path_rec, ib_cm_event and listen_id
pointers in several functions.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Make sure to check for "-EOPNOTSUPP" instead of "-ENOSYS" which is the
return code from ib_create_srq() in case that it not supported.
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Instead of declaring and passing a dummy 'bad_wr' pointer, pass NULL
as third argument to ib_post_(send|recv|srq_recv)().
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Fix to return a negative error code from the ipoib_neigh_hash_init()
error handling case instead of 0, as done elsewhere in this function.
Fixes: 515ed4f3aa ("IB/IPoIB: Separate control and data related initializations")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This table by default takes 32KiB which is 3rd memory order. Meanwhile,
this memory is not aimed for DMA operation and could be safely allocated
by vmalloc.
Signed-off-by: Jan Dakinevich <jan.dakinevich@virtuozzo.com>
Reviewed-by: Håkon Bugge <haakon.bugge@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The proper return code is -EOPNOTSUPP and not -ENOSYS when the function
isn't supported, also make sure to return the right error code
from ipoib_transport_dev_init() when ipoib_cm_dev_init() is supported.
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Make sure to use sizeof(...) instead of sizeof ... which is more
preferred.
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This commit replaces all the unsigned definitions in favour of 'unsigned
int' which is preferred.
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Use min_t() macro to avoid the casting when using min() macro, also fix
the type of "length" and "wc->byte_len" to be "unsigned int" and
"u32" which is the right type for each one of them.
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
While processing a path record entry in CM messages the associated GID
attribute is now also supplied.
Currently for RoCE a netdevice's net namespace pointer and ifindex are
stored in path record entry. Both of these fields of the netdev can change
anytime while processing CM messages. Additionally storing net namespace
without holding reference will lead to use-after-free crash. Therefore it
is removed. Netdevice information for RoCE is instead provided via
referenced gid attribute in ib_cm requests.
Such a design leads to a situation where the kernel can crash when the net
pointer becomes invalid. However today it is always initialized to
init_net, which cannot become invalid. In order to support processing
packets in any arbitrary namespace of the received packet, it is necessary
to avoid such conditions.
This patch removes the dependency on the net pointer and ifindex; instead
it will rely on SGID attribute which contains a pointer to netdev.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Use the sgid and other information from the path record to figure out the
sgid_attrs.
Store the selected table entry in the sgid_attr for everything else to
use.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
This patch replaces the ib_device_attr.max_sge with max_send_sge and
max_recv_sge. It allows ulps to take advantage of devices that have very
different send and recv sge depths. For example cxgb4 has a max_recv_sge
of 4, yet a max_send_sge of 16. Splitting out these attributes allows
much more efficient use of the SQ for cxgb4 with ulps that use the RDMA_RW
API. Consider a large RDMA WRITE that has 16 scattergather entries.
With max_sge of 4, the ulp would send 4 WRITE WRs, but with max_sge of
16, it can be done with 1 WRITE WR.
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: Selvin Xavier <selvin.xavier@broadcom.com>
Acked-by: Shiraz Saleem <shiraz.saleem@intel.com>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
If the gid_attr argument is NULL then the functions behave identically to
rdma_query_gid. ib_query_gid just calls ib_get_cached_gid, so everything
can be consolidated to one function.
Now that all callers either use rdma_query_gid() or ib_get_cached_gid(),
ib_query_gid() API is removed.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
In unicast_arp_send function there is an inconsistency in error handling
of path_rec_start call. If path_rec_start is called because of an absent
ah field, skb will be dropped. But if it is called on a creation of a
new path, or if the path is invalid, skb will be added to the tail of
path queue. In case of a new path it will be dropped on path_free, but
in case of invalid path it can stay in the queue forever.
This patch unifies the behavior, dropping skb in all cases
of path_rec_start failure.
Signed-off-by: Evgenii Smirnov <evgenii.smirnov@profitbricks.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We do a light flush on CLIENT_REREG and SM_CHANGE events. This goes
through and marks paths invalid. But we weren't always checking for this
validity when we needed to, and so we could keep using a path marked
invalid. What's more, once we establish a path with a valid ah, we put
a pointer to the ah in the neigh struct directly, so even if we mark the
path as invalid, as long as the neigh has a direct pointer to the ah, it
keeps using the old, outdated ah.
To fix this we do several things.
1) Put the valid flag in the ah instead of the path struct, so when we
put the ah pointer directly in the neigh struct, we can easily check the
validity of the ah on send events.
2) Check the neigh->ah and neigh->ah->valid elements in the needed
places, and if we have an ah, but it's invalid, then invoke a refresh of
the ah.
3) Fix the various places that check for path, but didn't check for
path->valid (now path->ah && path->ah->valid).
Reported-by: Evgenii Smirnov <evgenii.smirnov@profitbricks.com>
Fixes: ee1e2c82c2 ("IPoIB: Refresh paths instead of flushing them on SM change events")
Signed-off-by: Doug Ledford <dledford@redhat.com>
In ipoib_mcast_restart_task() the netif_addr_lock() is invoked prior
local_irq_save(). netif_addr_lock() should not be invoked in interrupt disabled
section, only in BH disabled sections.
The priv->lock is always acquired with disabled interrupts. The only place
where netif_addr_lock() and priv->lock nest ist ipoib_mcast_restart_task().
Drop the local_irq_save() and acquire priv->lock with spin_lock_irq() inside
the netif_addr locked section. It's safe to do so because the caller is either
a worker function or __ipoib_ib_dev_flush() which are both calling with
interrupts enabled (and since BH is enabled here, too so
netif_addr_lock_bh() needs to be used).
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This structure is not needed since the introduction of commit
'c42687784b9a ("IB/ipoib: Scatter-Gather support in connected mode")'
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
ib_find_gid() is only used by IPoIB driver. For IB link layer, GID table
entries are not based on netdevice. Netdevice parameter is unused here.
Therefore, it is removed.
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
netdev_wait_allrefs() could rebroadcast NETDEV_UNREGISTER event
multiple times until all refs are gone, which will result in calling
ipoib_delete_debug_files multiple times and printing a warning.
Remove the WARN_ONCE since checks of NULL pointers before calling
debugfs_remove are not needed.
Fixes: 771a525840 ("IB/IPoIB: ibX: failed to create mcg debug file")
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
On reboot SM can program port pkey table before ipoib registered its
event handler, which could result in missing pkey event and leave root
interface with initial pkey value from index 0.
Since OPA port starts with invalid pkey in index 0, root interface will
fail to initialize and stay down with no-carrier flag.
For IB ipoib interface may end up with pkey different from value
opensm put in pkey table idx 0, resulting in connectivity issues
(different mcast groups, for example).
Close the window by calling event handler after registration
to make sure ipoib pkey is in sync with port pkey table.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Alex Estrin <alex.estrin@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Feras Daoud