Setup of the receive and transmit DMA channels is very similar, so let's
consolidate.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fall back to PIO if DMA configuration failed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The various PIO loops are very similar. Consolidate into a single
function rspi_pio_transfer().
Both buffer pointers can be NULL, as RSPI supports TX-only mode, and
Dual/Quad SPI Transfers are unidirectional.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
RSPI needs dummy transfers to generate the SPI clock on receive.
RSPI-RZ and QSPI always do both transmit and receive.
Use the SPI core SPI_MASTER_MUST_RX/SPI_MASTER_MUST_TX infrastructure
instead of checking for the presence of buffers and providing dummy data
ourselves (for PIO), or providing a dummy buffer (for DMA).
rspi_receive_dma() now provides full duplex DMA transfers on RSPI, and is
renamed to rspi_send_receive_dma().
As the SPI core will always provide a TX buffer, the logic to choose
between DMA send and DMA send/receive in rspi_transfer_one() now has to
check for the presence of an RX buffer. Likewise for the DMA availability
tests in rspi_is_dma().
The buffer tests in qspi_transfer_one() are now always true, so they're
removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The 16-bit DMA support doesn't fit well within the SPI core DMA framework,
as it needs to manage its own double-sized temporary buffers, for handling
the interleaved data.
Remove it, as there is no in-tree board code that sets
rspi_plat_data.dma_width_16bit.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 8449fd76de ("spi: rspi: Merge
rspi_send_pio() and rspi_receive_pio()"), rspi_receive_init() is called
for transmit-only transfers too, while this is not needed.
Only call rspi_receive_init() when receiving, to preserve behavior on
RSPI on SH.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The calculation of the bit rate divider used a standard C division, which
rounds down the quotient. This may lead to a higher bitrate than requested.
Round up to avoid this.
E.g. on Koelsch, the SPI flash (configured for 30 MHz) was driven at 48.75
MHz. After this patch it's driven at a safe 24.375 MHz.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
While normal Dual and Quad SPI Transfers are unidirectional, we must do
a bidirectional transfer if loopback mode is enabled, else rx_buf is not
filled.
With spidev it seemed to work, as spidev uses the same buffer for
tranmission and reception.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
If spi_master.cleanup() is not needed, it can be left unimplemented.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
rspi_wait_for_interrupt() unconditionally enables interrupts, even when the
wait condition is already satisfied. This causes a high interrupt load (2
interrupts/byte for full-duplex Single SPI transfers, 1 interrupt/byte for
RSPI with TX Only mode, or QSPI in unidirectional Dual or Quad Transfer
mode).
Change this to return immediately when the wait condition is satisfied.
This dramatically reduces the interrupt load, especially in high-speed
Quad Transfer mode, and increases transfer speed, as no interrupts need to
be handled when there's space available in the output FIFO, or data
available in the input FIFO.
Benchmark results for QSPI on r8a7791 while reading 1 MiB from 30 MHz SPI
FLASH on the Koelsch development board:
Before:
Single SPI Dual SPI Quad SPI
Interrupts: 2096856 1048592 1048594
Mbps: 0.9 1.6 1.6
After:
Single SPI Dual SPI Quad SPI
Interrupts: 1048569 21295 8
Mbps: 0.7 10.8 12.9
I don't know why Single SPI slowed down a bit.
I've also verified functionality for RSPI-RZ on r7s72100, but don't have
benchmark results as there's no SPI FLASH connected to RSPI on the Genmai
development board. Unlike RSPI and QSPI, RSPI-RZ has separate interrupts
for RX and TX, which shows that Single SPI transfers now generate (mostly)
RX interrupts, as expected.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fixes an issue that the following build error happens when
the CONFIG_OF is not set:
drivers/spi/spi-rspi.c: In function 'rspi_probe':
drivers/spi/spi-rspi.c:1203:26: error: 'rspi_of_match' undeclared (first use in this function)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for Quad and Dual SPI Transfers on the Renesas Quad Serial
Peripheral Interface, as found in R-Car Gen2 SoCs like R-Car H2 (r8a7790)
and R-Car M2 (r8a7791):
- Add unidirectional transfer methods for Quad/Dual SPI Transfers.
- Program the sequencer to handle SPI messages with multiple transfer
modes when Quad or Dual transfers are enabled for an SPI slave.
Up to 4 transfer modes per SPI message are supported by the hardware.
- Advertise the availability of Quad and Dual SPI modes on QSPI.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
There's only one RSPI/QSPI clock, so we can use NULL as the clock ID
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Get the driver ready for the migration to the common clock framework by
calling clk_prepare_enable() and clk_disable_unprepare().
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for specifying loopback mode.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for the RSPI variant in the RZ/A1H (r7s72100) SoC.
Main differences with RSPI on SH are:
- Lack of TX only mode, hence we always have to use full duplex
transfers,
- The Data Register must be accessed used 8-bit operations.
RSPI on RZ is matched using the new "rspi-rz" platform device name.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for multiple interrupts, based on the SDK reference code.
This is needed for RZ/A1H, which supports 3 interrupts.
When using multiple interrupts, they must be called "rx" (SPRI) and "tx"
(SPTI). The error interrupt (SPEI) is not used, as it matters for slave
mode only.
When using a single interrupt, it may be called "mux". If it cannot be
found, the first interrupt in the device's resources will be used.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
qspi_send_pio() and qspi_receive_pio() are very similar: they both send
and receive full duplex data to/from the hardware, but ignore the data
stream in the unused direction.
Merge them into qspi_transfer_out_in(), now supporting real full duplex.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
rspi_send_pio() and rspi_receive_pio() are very similar:
- the former only sends data, using TX Only Mode,
- the latter sends and receives full duplex data to/from the hardware,
but uses dummy transmit data.
Merge them into rspi_transfer_out_in(), now supporting full duplex if
needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Split off qspi_transfer_one() (which doesn't support DMA yet) from
rspi_transfer_one().
Replace the abstraction of send_pio()/receive_pio() by the abstracrion of
transfer_one().
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add helpers rspi_data_{out,in,out_in}() to write, read, or write and
read data to/from the Data Register, taking care of waiting until data
or space is available in the buffers.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add rspi_{write,read}_data(), to abstract 8-bit (QSPI, and RSPI on RZ/A1H)
versus 16-bit (RSPI) Data Register access.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Let the generic SPI core handle SPI messages, calling into our
rspi_transfer_one() method.
rspi_assert_ssl() and rspi_negate_ssl() are absorbed into
rspi_prepare_message() and rspi_unprepare_message(), as they actually
enable/disable the whole SPI function, instead of just (de)asserting the
chip select line.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The implementation in spi_setup() already set spi->bits_per_word = 8 when
spi->bits_per_word is 0 before calling spi->master->setup.
So we don't need to do it again in setup() callback.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for specifying the SPI clock phase and polarity, based on the
SDK reference code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make it more obvious that this value is dummy data.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove useless casts, and do not cast away const.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The overrun flag should be cleared in the SPI Status Register, not in the
SPI Control Register, based on the SDK sample code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@linaro.org>
SH7757 doesn't pass platform data, in which case spi-rspi uses default
parameters.
However, commit 5ce0ba8865 ("spi: rcar: add
Renesas QSPI support on RSPI") added a new user of the platform data, but
forgot to check for its validity first, causing a NULL pointer dereference
on SH7757.
Add the missing check to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_spi_register_master() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This simplies error and cleanup code paths.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The platform driver data is set to point to the rspi_data structure at
probe time. Calling spi_master_get() on the pointer is just plain wrong
and only works by chance. Fix it by using the platform driver data
directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The transfer data length variable is set based on the desired access
size, without a default case. This results in a compiler warning, even
though the access size is always set to a supported value. Create a
default case to silence the warning.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The R8A7790 has QSPI module which added into RSPI together.
The transmit or receive data should be read from or written to
with the longword-, word-, or byte-access width. Modify word-
access to byte-access. In 16-bit data register, QSPI send or
receive datas access from high 8-bit while RSPI send or receive
datas access from low 8-bit on single mode.
Modify to reset transmit-receive buffer data and reading dummy
after data are transmited. RSPI has a TXMD bit on control
register(SPCR) to set transmit-only mode when transmit data or
Full-duplex synchronous mode when receive data. In QSPI the TXMD
bit is not supported, so after transmit data, dummy should be
read and before transmit or receive data the bufer register
should be reset.
This driver is the implementation of send and receive pio only,
DMA is not supported at this time.
Without this patch, it will occur error when transmit and receive
Signed-off-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Mark Brown <broonie@linaro.org>
The R8A7790 has QSPI module which is very similar to RSPI.
This patch adds into RSPI module together to supports QSPI module.
Signed-off-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Mark Brown <broonie@linaro.org>
In rspi_remove(), current code dereferences rspi after spi_unregister_master(),
thus add an extra spi_master_get() call is necessary to prevent use after free.
Current code already has an extra spi_master_put() call in rspi_remove(), so
this patch just adds a spi_master_get() call rather than a spi_master_get() with
spi_master_put() calls.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Don't rely on shdma dhaengine driver getting DMA slave addresses from its
slave configuration. Instead provide those addresses, using a
dmaengine_slave_config() call.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Bill Pemberton has done most of the legwork on this series. I've used
his script to purge the attributes from the drivers/gpio tree.
Reported-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Because the latest shdma driver changed, it caused build error in
the spi-rspi driver. This patch fixed the build error.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds dmaengine supporting using sh_dma driver. The module
receives data by DMAC, it also needs TX DMAC to generate SPI's clocks.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The SH7757 has RSPI module. This patch supports it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Geert Uytterhoeven