The F54 Report Data is apparently read through a fifo and for
the smbus protocol that means that between reading a block of 32
bytes the rmiaddr shouldn't be incremented. However, changing
that causes other non-fifo reads to fail and so that change was
reverted.
This patch changes just the F54 function and it now reads 32 bytes
at a time from the fifo, using the F54_FIFO_OFFSET to update the
start address that is used when reading from the fifo.
This has only been tested with smbus, not with i2c or spi. But I
suspect that the same is needed there since I think similar
problems will occur there when reading more than 256 bytes.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Timo Kaufmann <timokau@zoho.com>
Link: https://lore.kernel.org/r/20200115124819.3191024-3-hverkuil-cisco@xs4all.nl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The v4l2-compliance utility reported several V4L2 API compliance
issues:
- the sequence counter wasn't filled in
- the sequence counter wasn't reset to 0 at the start of streaming
- the returned field value wasn't set to V4L2_FIELD_NONE
- the timestamp wasn't set
- the payload size was undefined if an error was returned
- min_buffers_needed doesn't need to be initialized
Fix these issues.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de
Link: https://lore.kernel.org/r/20191119105118.54285-3-hverkuil-cisco@xs4all.nl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver forgets to destroy workqueue in remove() similarly to what is
done when probe() fails. Add a call to destroy_workqueue() to fix it.
Since unregistration will wait for the work to finish, we do not need to
cancel/flush the work instance in remove().
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191114023405.31477-1-hslester96@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver for F54 just polls the status and doesn't even have a IRQ
handler registered. Make sure to disable all F54 IRQs, so we don't crash
the kernel on a nonexistent handler.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20191105114402.6009-1-l.stach@pengutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The body of the for loop is only ever run once as the second standard_report
element is never changed from its initial zero init, so the loop condition is
never satisfies after the first run. Equally the start member of the first
element is never changed from 0, so the index offset is always a constant 0.
Remove this needless obfuscation of the code and write it in a straight
forward manner.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20191104114454.10500-3-l.stach@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The video buffer used by the queue is a vb2_v4l2_buffer, not a plain
vb2_buffer. Using the wrong type causes the allocation of the buffer
storage to be too small, causing a out of bounds write when
__init_vb2_v4l2_buffer initializes the buffer.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Fixes: 3a762dbd53 ("[media] Input: synaptics-rmi4 - add support for F54 diagnostics")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191104114454.10500-1-l.stach@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not enumerate all formats, some of which the device may not even
support. Instead, only report the one fixed format of the currently
selected input that will survive try_fmt/s_fmt.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver doesn't set an initial video format until s_input is called:
$ v4l2-ctl -d /dev/v4l-touch0 --get-input
Video input : 0 (Normalized 16-Bit Image: ok)
$ v4l2-ctl -d /dev/v4l-touch0 --get-fmt-video
Width/Height : 0/0
Pixel Format : ''
[...]
$ v4l2-ctl -d /dev/v4l-touch0 --set-input 0
Video input set to 0 (Normalized 16-Bit Image: Touch, ok)
$ v4l2-ctl -d /dev/v4l-touch0 --get-fmt-video
Width/Height : 71/40
Pixel Format : 'TD16'
[...]
To fix this, initialize the video format to input 0 during probe.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- the main change is a fix for my brain-dead patch to PS/2 button
reporting for some protocols that made it in 4.17
- there is a new driver for Spreadtum vibrator that I intended to send
during merge window but ended up not sending the 2nd pull request.
Given that this is a brand new driver we should not see regressions
here
- a fixup to Elantech PS/2 driver to avoid decoding errors on Thinkpad
P52
- addition of few more ACPI IDs for Silead and Elan drivers
- RMI4 is switched to using IRQ domain code instead of rolling its own
implementation
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: psmouse - fix button reporting for basic protocols
Input: xpad - fix GPD Win 2 controller name
Input: elan_i2c_smbus - fix more potential stack buffer overflows
Input: elan_i2c - add ELAN0618 (Lenovo v330 15IKB) ACPI ID
Input: elantech - fix V4 report decoding for module with middle key
Input: elantech - enable middle button of touchpads on ThinkPad P52
Input: do not assign new tracking ID when changing tool type
Input: make input_report_slot_state() return boolean
Input: synaptics-rmi4 - fix axis-swap behavior
Input: synaptics-rmi4 - fix the error return code in rmi_probe_interrupts()
Input: synaptics-rmi4 - convert irq distribution to irq_domain
Input: silead - add MSSL0002 ACPI HID
Input: goldfish_events - fix checkpatch warnings
Input: add Spreadtrum vibrator driver
Convert the RMI driver to use the standard mechanism for
distributing IRQs to the various functions.
Tested on:
* S7300 (F11, F34, F54)
* S7817 (F12, F34, F54)
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Acked-by: Christopher Heiny <cheiny@synaptics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The array rmi_f54_report_type_names is local to the source and does
not need to be in global scope, so make it static. Also make the array
const char * const.
Cleans up sparse warning:
symbol 'rmi_f54_report_type_names' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The F54 driver is currently only using the first 6 bytes of F54 so there is
no need to read all 27 bytes. Some Dell systems (Dell XP13 9333 and
similar) have an issue with the touchpad or I2C bus when reading reports
larger then 16 bytes. Reads larger then 16 bytes are reported in two HID
reports. Something about the back to back reports seems to cause the next
read to report incorrect data. This results in F30 failing to load and the
click button failing to work.
Previous issues with the I2C controller or touchpad were addressed in:
commit 5b65c2a029 ("HID: rmi: check sanity of the incoming report")
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=195949
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
F54 diagnostics report functions provide data based on the number of
enabled rx and tx electrodes, which is not identical to the number of
electrodes reported with F54:Query0 and F54:Query1. Those values report
the number of supported electrodes, not the number of enabled electrodes.
The number of enabled electrodes can be determined by analyzing F55:Ctrl1
(sensor receiver assignment) and F55:Ctrl2 (sensor transmitter assignment).
Propagate the number of enabled electrodes from F55 to F54 to avoid
corrupted output if not all electrodes are enabled.
Fixes: 3a762dbd53 ("[media] Input: synaptics-rmi4 - add support for F54 ...")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We should unlock before returning on this error path.
Fixes: 3a762dbd53 ('[media] Input: synaptics-rmi4 - add support for F54 diagnostics')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add copyright lines for Zodiac who paid for the V4L touch work.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Function 54 implements access to various RMI4 diagnostic features.
This patch adds support for retrieving this data. It registers a V4L2
device to output the data to user space.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Tested-by: Andrew Duggan <aduggan@synaptics.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Hans Verkuil