REGMAP_SCCB is selected by ov772x and ov9650 drivers,
but CONFIG_REGMAP may not, so building will fails:
rivers/media/i2c/ov772x.c: In function ov772x_probe:
drivers/media/i2c/ov772x.c:1360:22: error: variable ov772x_regmap_config has initializer but incomplete type
static const struct regmap_config ov772x_regmap_config = {
^~~~~~~~~~~~~
drivers/media/i2c/ov772x.c:1361:4: error: const struct regmap_config has no member named reg_bits
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 5bbf32217b ("media: ov772x: use SCCB regmap")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190704093553.49904-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch to bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On buses like SlimBus and SoundWire which does not support
gather_writes yet in regmap, A bulk write on paged register
would be silently ignored after programming page.
This is because local variable 'ret' value in regmap_raw_write_impl()
gets reset to 0 once page register is written successfully and the
code below checks for 'ret' value to be -ENOTSUPP before linearising
the write buffer to send to bus->write().
Fix this by resetting the 'ret' value to -ENOTSUPP in cases where
gather_writes() is not supported or single register write is
not possible.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add basic support for i3c bus.
This is a simple implementation that only give support
for SDR Read and Write commands.
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There were a few files in the regmap code that did not have SPDX
identifiers on them, so fix that up. At the same time, remove the "free
form" text that specified the license of the file, as that is impossible
for any tool to properly parse.
Also, as Mark loves // comment markers, convert all of the headers to be
the same to make things look consistent :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
regmap provides a couple of ways to validate the register range used.
a) maxim allowed register, b) writable/readable register tables,
c) callback function that can be provided by the driver to validate
a register. regmap framework should verify if registers
are writeable before every write operation. However this doesn't
seems to happen in every situation.
The method `_regmap_raw_write_impl` is only using the `writeable_reg`
callback to verify if register is writeable, ignoring the other two.
This can lead to undefined behaviour since this allows to write to
registers that could be declared un-writeable by using any other
option.
Change `_regmap_raw_write_impl` to use the `regmap_writeable` method
to verify if registers are writable before the write operation.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Checking for value of type default value just after allocating will
always be zero and the type register default values will never be read,
so fix this!
Without this patch setting irq type will be silently ignored.
Patch "regmap: regmap-irq: Remove default irq type setting from core"
did remove the default mask but it forgot to remove the check before
reading the default type register.
Fixes: 84267d1b18 ("regmap: regmap-irq: Remove default irq type setting from core")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Improve the speed of the loop jumping to the next
available register
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On one hand commit 28644c809f ("regmap: Add the rbtree cache support")
added 'regcache_rbtree_node' as packed structure, while on the other hand
commit e977145aea ("[RBTREE] Add explicit alignment to sizeof(long)
for struct rb_node.") declared struct 'rb_node' as aligned.
Solve the ambiguity of placing aligned structure in a packed one by
removing the packed attribute from struct. This seems to be the behavior
of gcc anyway.
This removes the following warning (W=1):
drivers/base/regmap/regcache-rbtree.c:36:1: warning: alignment 1 of 'struct regcache_rbtree_node' is less than 4 [-Wpacked-not-aligned]
Cc: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is bunch of devices with multiple logical blocks which
can generate interrupts. It's not a rare case that the interrupt
reason registers are arranged so that there is own status/ack/mask
register for each logical block. In some devices there is also a
'main interrupt register(s)' which can indicate what sub blocks
have interrupts pending.
When such a device is connected via slow bus like i2c the main
part of interrupt handling latency can be caused by bus accesses.
On systems where it is expected that only one (or few) sub blocks
have active interrupts we can reduce the latency by only reading
the main register and those sub registers which have active
interrupts. Support this with regmap-irq for simple cases where
main register does not require acking or masking.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If client have not provided the mask base register then do not
write into the mask register.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Jinyoung Park <jinyoungp@nvidia.com>
Signed-off-by: Venkat Reddy Talla <vreddytalla@nvidia.com>
Signed-off-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Do not return error if irq-type setting is requested for
controlloer which does not support this. This is how
regmap-irq has previously handled the undupported type
settings and existing drivers seem to be upset if failure
is now reported.
Fixes: 1c2928e3e3 ("regmap: regmap-irq/gpio-max77620: add level-irq support")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some interrupt controllers whose interrupts are acked on read will set
the status bits for masked interrupts without changing the state of
the IRQ line.
Some chips have an additional "feature" where if those set bits are
not cleared before unmasking their respective interrupts, the IRQ
line will change the state and we'll interpret this as an interrupt
although it actually fired when it was masked.
Add a new field to the irq chip struct that tells the regmap irq chip
code to always clear the status registers before actually changing the
irq mask values.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add level active IRQ support to regmap-irq irqchip. Change breaks
existing regmap-irq type setting. Convert the existing drivers which
use regmap-irq with trigger type setting (gpio-max77620) to work
with this new approach. So we do not magically support level-active
IRQs on gpio-max77620 - but add support to the regmap-irq for chips
which support them =)
We do not support distinguishing situation where HW supports rising
and falling edge detection but not both. Separating this would require
inventing yet another flags for IRQ types.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The common code should not set IRQ type. Read HW defaults to the
cache at startup instead of forcing type to EDGE_BOTH. If
default setting is needed this should be done via normal
mechanisms or by chip specific code if normal mechanisms are not
suitable for some reason. Common regmap-irq code should not have
defaults hard-coded but keep the HW/boot defaults untouched.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some interrupt controllers use separate bits for controlling rising
and falling edge interrupts in the mask register i.e. they have one
interrupt for rising edge and one for falling.
We already handle the case where we have a single interrupt in the
mask register and a separate type configuration register.
Add a new switch to regmap_irq_chip which tells the framework to use
the mask_base address for configuring the edge of the interrupts that
define type_falling/rising_mask values.
For such interrupts we never update the type_base bits. For interrupts
that don't define type masks or their regmap irq chip doesn't set the
type_in_mask to true everything stays the same.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the checking of the LOG_DEVICE into a function to reduce the
number of #ifdefs and ensure more of the code gets compiled/checked,
and make it easier to change this for internal debugging purposes
(such as checking >1 device).
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regmap API had a noinc_read function added for instances where devices
supported returning data from an internal FIFO in a single read.
This commit adds the noinc_write variant to allow writing to a non
incrementing register, this is used in devices such as the sx1301 for
loading firmware.
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Split regmap_config.use_single_rw into use_single_read and
use_single_write. This change enables drivers of devices which only
support bulk operations in one direction to use the regmap_bulk_*()
functions for both directions and have their bulk operation split into
single operations only when necessary.
Update all struct regmap_config instances where use_single_rw==true to
instead set both use_single_read and use_single_write. No attempt was
made to evaluate whether it is possible to set only one of
use_single_read or use_single_write.
Signed-off-by: David Frey <dpfrey@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some devices have individual registers that don't autoincrement the
register address during bulk reads but instead repeatedly read the same
value, for example for monitoring GPIOs or ADCs. Add support for these.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAltsE8YTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0DeLB/sHEWAdyUCz9dO9pDdpi6WfpnKXuCCd
ZFnx8VXBvzVLRCZYGXuMOUEzBQU2lTr2KPFDmE1k4FclyiWaI+hRIJ0s/x8FAl51
EFDoR4TM7t2n2aY0sPQCZKnoAhdQ9YPxlA9JjDUE57h0KoC76Dh8OB44dlAlxUAY
PUjkv64/7AtvkBX7UZPQxckaPOLKM00P/hXwCB9MZCkjqnSWkUGgNCWPgKn9j2yL
jiUQO0Wo9u8RkvYvndHPkh4NzgeH1sUFUdNys/Fopu6C2miIYBNKzvEo2OXhelHf
k5rsoMQXYdiPdy4vRbeaWFetyEeBjxKIAQHKD0WJviFPw8j+ET+2GNjx
=p0Mu
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAltsFCwTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0NcxB/wMqH+78D7GdJfMkxMKhCHFUxozfCe9
cgWgZ7+vlWpIwEGvM65FHMrFyc5ZrS3/vD6Hy8lqpsqGBVv6wS6Z0lsoOyj/QvTl
T8USWKvQnvtzlPY5lRZL0xuGiaGGtpGa0eaLKH2lY7uvoge0oHz8VV6ar5y7eA1S
1INBpgTdHJgCQLZoc1pFNOcZ0EMFl6ZAygIWJTpqIwoQlvPEgtCQ4wjPlMUKrevP
psJWd9obyM6+02mYFVMAlYpcMSoZ/MjPeMb7VGhLGwA1BA6dNcbiIeS7GCeH2r/i
/vxvarsEm38MfLBIyORW06onHyRhVwXdLoD1jblmvYtRlfW5ANjr5g/O
=mbi1
-----END PGP SIGNATURE-----
Merge tag 'regmap-noinc-read' into regmap-4.19
regmap: Support non-incrementing registers
Some devices have individual registers that don't autoincrement the
register address during bulk reads but instead repeatedly read the same
value, for example for monitoring GPIOs or ADCs. Add support for these.
The regmap API usually assumes that bulk read operations will read a
range of registers but some I2C/SPI devices have certain registers for
which a such a read operation will return data from an internal FIFO
instead. Add an explicit API to support bulk read without range semantics.
Some linux drivers use regmap_bulk_read or regmap_raw_read for such
registers, for example mpu6050 or bmi150 from IIO. This only happens to
work because when caching is disabled a single regmap read op will map
to a single bus read op (as desired). This breaks if caching is enabled and
reg+1 happens to be a cacheable register.
Without regmap support refactoring a driver to enable regmap caching
requires separate I2C and SPI paths. This is exactly what regmap is
supposed to help avoid.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix typos 's/wit/with/' in the comments and sort headers alphabetically
in order to avoid duplicate includes in future.
Fixes: bcf7eac3d9 ("regmap: add SCCB support")
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is an I2C subset.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAltPUrMTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0KODB/oDV+4c82VIUopoaXxK8PbBqDMn5n2r
EKyb1D/GFiT54x2666arRT1NymL/uk6/nK1hryd/4HE5zB1lUQnu/Z7HCHgF4N+/
iWHtAgFUSZtNlMTRT6DW/tcsNDGnH9vjNJUhOLH9Y21h3Q4BpOo5HQVR8ynN4TDh
2inSy5qgADyrosxRpW5mp0Nt0tpFTfvYOHoRaLTbQUbBnpb/MmqcTzkYHcVNqA8V
7+e9/SOVU0XXHQD5k28F7eB84Mk+TXQrZQ181RwNOKUf3je86Im6WfrFqKHqKP5N
UAq28AjsjRiBs1qwOYK0ytWR8gQvs39cZmdud507R1mLWEO4/++TruRt
=wkUm
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAltPUyETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0CJsB/oD+83KWX8V1Q4HhaO3e6BN2SPYphQr
jbImC9QUSRl/65+0ek6VjqLu4znY/LARRjNThN0l01wvWv7+h71DJBSKL67zK9en
h4Lr8ZoewBQ408YaC5zl7ilFXgRBMhfCanDWWHv8jAv1rk9VQU8q9uNGo518e0Ks
2Gg/zTmQYp7dNMHsVO4AEr3UQye1yZdGdP1q1yk3nbNgZbDq4xWWZWl1p4Iy+QG3
e4SY+OYenQC/+pafUQOzPoiG3I/f8RAQG9SAtne+gtIyF85+Q8mVizuU89GdtH3O
rKcaiNk/FpSbcBxAXEGb0qNy6PW6gnAbSznrOdc7MEj2V5E3KfoR7oVO
=VO/+
-----END PGP SIGNATURE-----
Merge tag 'regmap-sccb' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into regmap-4.19
regmap: Add support for SCCB
This is an I2C subset.
This adds Serial Camera Control Bus (SCCB) support for regmap API that
is intended to be used by some of Omnivision sensor drivers.
The ov772x and ov9650 drivers are going to use this SCCB regmap API.
The ov772x driver was previously only worked with the i2c controller
drivers that support I2C_FUNC_PROTOCOL_MANGLING, because the ov772x
device doesn't support repeated starts. After commit 0b964d183c
("media: ov772x: allow i2c controllers without
I2C_FUNC_PROTOCOL_MANGLING"), reading ov772x register is replaced with
issuing two separated i2c messages in order to avoid repeated start.
Using this SCCB regmap hides the implementation detail.
The ov9650 driver also issues two separated i2c messages to read the
registers as the device doesn't support repeated start. So it can
make use of this SCCB regmap.
Cc: Mark Brown <broonie@kernel.org>
Cc: Peter Rosin <peda@axentia.se>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SLIMbus supports upto 16 bytes in value management messages,
so add support to read/writes upto 16 bytes.
This also removes redundant single register reg_read/reg_write.
Also useful for paged register access on SLIMbus interfaced codecs.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
As per SLIMBus specs Value Elements and Information Elements
address map ranges from 0x000 - 0xFFF.
So allow register addresses up to 16 bits
Fixes: 7d6f7fb053 ("regmap: add SLIMbus support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Capability to attach an existing clk to a MMIO regmap was
introduced in 4.17rc1.
However, when using attached clk, regmap does not do the clk_get.
Therefore it should not do the clk_put when freeing the MMIO
regmap context.
There does not appear to be any users of attached clocks yet
so this would be a good time to make this change before anything
depends on the existing behaviour.
Signed-off-by: James Kelly <jamespeterkelly@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently when debugfs_create_dir() fails we receive a warning message
that provides no indication as to what was the directory entry that
failed to be created.
Improve the warning message by printing the directory name that failed
in order to help debugging.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Free map->debugfs_name when debugfs_create_dir() failed to avoid memory
leak.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When allocating dummy names we need to store a pointer to the string we
allocate so that we don't leak it on free.
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 9b947a13e7 ("regmap: use debugfs even when no device")
allows the usage of regmap debugfs even when there is no device
associated, which causes several warnings like this:
(NULL device *): Failed to create debugfs directory
This happens when the debugfs file name is 'dummy'.
The first dummy debugfs creation works fine, but subsequent creations
fail as they have all the same name.
Disambiguate the 'dummy' debugfs file name by adding a suffix entry,
so that the names become dummy0, dummy1, dummy2, etc.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
regmap_init_mmio_clk allows to specify a clock that needs to be enabled
while accessing the registers.
However, that clock is retrieved through its clock ID, which means it will
lookup that clock based on the current device that registers the regmap,
and, in the DT case, will only look in that device OF node.
This might be problematic if the clock to enable is stored in another node.
Let's add a function that allows to attach a clock that has already been
retrieved to a regmap in order to fix this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The handling for the first two cases in regmap_bulk_write is
essentially identical. The first case is just a better implementation of
the second, supporting 8 byte registers and doing the locking manually to
avoid bouncing the lock for each register. Drop some redundant code by
removing the second of these cases and allowing both situations to be
handled by the same code.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Raw writes may need to be split into small chunks if max_raw_write is
set. Tidy up the code implementing this, the new code is slightly
clearer, slightly shorter and slightly more efficient.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently regmap_bulk_write will split a write into chunks before
calling regmap_raw_write if max_raw_write is set. It is more logical
for this handling to be inside regmap_raw_write itself, as this
removes the need to keep re-implementing the chunking code, which
would be the same for all users of regmap_raw_write.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the case were the bulk transaction is split up into smaller chunks
data is passed directly to regmap_raw_write. However regmap_bulk_write
uses data in host endian and regmap_raw_write expects data in device
endian. As such if the host and device differ in endian the wrong data
will be written to the device. Correct this issue using a similar
approach to the single raw write case below it, duplicate the data
into a new buffer and use parse_inplace to format the data correctly.
Fixes: adaac45975 ("regmap: Introduce max_raw_read/write for regmap_bulk_read/write")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This registers regmaps with debugfs even when they do not have an
associated device. For example, this is common for syscon regmaps.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes a possible NULL pointer dereference oops in
regmap_name_read_file() when the regmap does not have a device
associated with it. For example syscon regmaps retrieved with
syscon_regmap_lookup_by_compatible() don't have a device.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Bulk reads may potentially read a lot of registers and regmap_read will
take and release the regmap lock for each register. Avoid bouncing
the lock so frequently by holding the lock locally and calling
_regmap_read instead. This also has the nice side-effect that all the
reads will be done atomically so no other threads can sneak a write in
during the regmap_bulk_read.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Raw reads may need to be split into small chunks if max_raw_read is
set. Tidy up the code implementing this, the new code is slightly
clearer, slightly shorter and slightly more efficient.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently regmap_bulk_read will split a read into chunks before
calling regmap_raw_read if max_raw_read is set. It is more logical for
this handling to be inside regmap_raw_read itself, as this removes the
need to keep re-implementing the chunking code, which would be the
same for all users of regmap_raw_read.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As a helper function exists for calculating register offsets lets use
that rather than open coding with the reg_stride.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A bulk read can be implemented either through regmap_raw_read, or
by reading each register individually using regmap_read. Both
regmap_read and regmap_bulk_read should return values in native
endian. In the individual case the current implementation calls
format_val to put the data into the output array, which can cause
endian issues. The regmap_read will have already converted the data
into native endian, if the hosts endian differs from the device then
format_val will switch the endian back again.
Rather than using format_val simply use the code that is called if
there is no format_val function. This code supports all cases except
24-bit but there don't appear to be any users of regmap_bulk_read for
24-bit. Additionally, it would have to be a big endian host for the
old code to actually function correctly anyway.
Fixes: 15b8d2c41f ("regmap: Fix regmap_bulk_read in BE mode")
Reported-by: David Rhodes <david.rhodes@cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The cache pointer points to the actual memory used by the cache, as the
comparison here is looking for the type of the cache it should check
against cache_type.
Fixes: 1ea975cf1e ("regmap: Add a function to check if a regmap register is cached")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current implementation is broken for regmaps that have a reg_stride,
since it doesn't take the stride into account. Correct this by using the
helper function to calculate the register offset.
Fixes: f01ee60fff ("regmap: implement register striding")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit message says that we are allowed to read and write up to 32
bytes but the code only allows us to write 31 bytes. In other words,
the ">=" should be changed to ">". But this is already checked in
regmap_raw_read()/write() so we can just remove the if statemetents.
Fixes: 29332534e2 ("regmap-i2c: Add smbus i2c block support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We're supposed to be checking that "val_len" is not too large but
instead we check if it is smaller than the max.
The only function affected would be regmap_i2c_smbus_i2c_write() in
drivers/base/regmap/regmap-i2c.c. Strangely that function has its own
limit check which returns an error if (count >= I2C_SMBUS_BLOCK_MAX) so
it doesn't look like it has ever been able to do anything except return
an error.
Fixes: c335931ed9 ("regmap: Add raw_write/read checks for max_raw_write/read sizes")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Here is the big pull request for char/misc drivers for 4.16-rc1.
There's a lot of stuff in here. Three new driver subsystems were added
for various types of hardware busses:
- siox
- slimbus
- soundwire
as well as a new vboxguest subsystem for the VirtualBox hypervisor
drivers.
There's also big updates from the FPGA subsystem, lots of Android binder
fixes, the usual handful of hyper-v updates, and lots of other smaller
driver updates.
All of these have been in linux-next for a long time, with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLuZw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynS4QCcCrPmwfD5PJwaF+q2dPfyKaflkQMAn0x6Wd+u
Gw3Z2scgjETUpwJ9ilnL
=xcQ0
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big pull request for char/misc drivers for 4.16-rc1.
There's a lot of stuff in here. Three new driver subsystems were added
for various types of hardware busses:
- siox
- slimbus
- soundwire
as well as a new vboxguest subsystem for the VirtualBox hypervisor
drivers.
There's also big updates from the FPGA subsystem, lots of Android
binder fixes, the usual handful of hyper-v updates, and lots of other
smaller driver updates.
All of these have been in linux-next for a long time, with no reported
issues"
* tag 'char-misc-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (155 commits)
char: lp: use true or false for boolean values
android: binder: use VM_ALLOC to get vm area
android: binder: Use true and false for boolean values
lkdtm: fix handle_irq_event symbol for INT_HW_IRQ_EN
EISA: Delete error message for a failed memory allocation in eisa_probe()
EISA: Whitespace cleanup
misc: remove AVR32 dependencies
virt: vbox: Add error mapping for VERR_INVALID_NAME and VERR_NO_MORE_FILES
soundwire: Fix a signedness bug
uio_hv_generic: fix new type mismatch warnings
uio_hv_generic: fix type mismatch warnings
auxdisplay: img-ascii-lcd: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
uio_hv_generic: add rescind support
uio_hv_generic: check that host supports monitor page
uio_hv_generic: create send and receive buffers
uio: document uio_hv_generic regions
doc: fix documentation about uio_hv_generic
vmbus: add monitor_id and subchannel_id to sysfs per channel
vmbus: fix ABI documentation
uio_hv_generic: use ISR callback method
...
All zero read and write masks in the regmap config are used to signal no
special mask is needed and the bus defaults are used. In some devices
all zero read/write masks are the special mask and bus defaults should
not be used. To signal this a new variable is added.
For example SPI often sets bit 7 in address to signal to the device a
read is requested. On TI AFE44xx parts with SPI interfaces no bit
needs to be set as registers are either read or write only and the
operation can be determined from the address only. For this case both
masks must be zero to not effect the address.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This makes the code slightly more readable and allows for cleaner
addition of functionality in later patches.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SoundWire bus provides sdw_read() and sdw_write() APIs for Slave
devices to program the registers. Provide support in regmap for
SoundWire bus.
Signed-off-by: Hardik T Shah <hardik.t.shah@intel.com>
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the hwlock id 0 is valid for hardware spinlock core, but now id 0
is treated as one invalid value for regmap. Thus we should add one extra
flag for regmap config to indicate if a hardware spinlock should be used,
then id 0 can be valid for regmap to request.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a follow-up to commit a5ba91c380 ("regmap: debugfs: emit a
debug message when locking is disabled"). I figured that a user may
see this message, grep the code, come to this place and he still won't
know why we actually disabled debugfs.
Add a comment explaining the reason.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
We currently silently omit creating the debugfs entries when regmap
locking is disabled. Users may not be aware of the reason for which
regmap files don't show up in debugfs. Add a dev_dbg() message
explaining that.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
The map->work_buf is a buffer preallocated in __regmap_init() with size
allowing it to store all 3 parts of a buffer - reg, pad and val. While
reg and val parts are always properly setup before each transaction, the
pad part is left at its default value (zeros). Until it is overwritten,
that is.
_regmap_bus_read(), when calling _regmap_raw_read() uses beginning of
work_buf as a place to store data read. Usually that is fine but if
val_bits > reg_bits && pad_bits > 0, padding area of work_buf() may get
overwritten. Since padding is not zeroed before each transaction,
garbage will be used on next calls.
This patch moves the val pointer used for _regmap_raw_read() to point
to a part of work_buf intended for storing value read.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support to read/write SLIMbus value elements.
Currently it only supports byte read/write. Adding this support in
regmap would give codec drivers more flexibility when there are more
than 2 control interfaces like SLIMbus, i2c.
Without this patch each codec driver has to directly call SLIMbus value
element apis, and this could would get messy once we want to add i2c
interface to it.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we just copy over the pointer passed to regmap_init() in
the regmap config struct. To be on the safe side: duplicate the string
with kstrdup_const() so that if an unaware user passes an address to
a stack-allocated buffer, we won't crash.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
The recently added support for disabling the regmap internal locking left
debugfs enabled for devices with the locking disabled. This is a problem
since debugfs allows userspace to do things like initiate reads from the
hardware which will use the scratch buffers protected by the regmap locking
so could cause data corruption.
For safety address this by just disabling debugfs for these devices. That
is overly conservative since some of the debugfs files just read internal
data structures but it's much simpler to implmement and less likely to
lead to problems with tooling that works with debugfs.
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Minor naming convention tweak.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have a use case in the at24 EEPROM driver (recently converted to
using regmap instead of raw i2c/smbus calls) where we read from/write
to the regmap in a loop, while protecting the entire loop with
a mutex.
Currently this implicitly makes us use two mutexes - one in the driver
and one in regmap. While browsing the code for similar use cases I
noticed a significant number of places where locking *seems* redundant.
Allow users to completely disable any locking mechanisms in regmap
config.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hwspinlock was changed to a bool by commit d048236dfd
("hwspinlock: Change hwspinlock to a bool"), so we do not need
the REGMAP_HWSPINLOCK config to select hwspinlock or not.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
After several quiet kernel releases we've got a couple of new features
in regmap, support for using hwspinlocks as the lock for the internal
data structures and a helper for polling on regmap_fields. The Kconfig
dependencies on hwspinlocks were annoyingly difficult to squash between
things behaving surprisingly and randconfig, I could've squashed those
commits down but might've have caused hassle with other trees trying to
use the new support.
- Support for using a hwspinlock to protect the regmap.
- An iopoll style helper for regmap_field.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAloJkKUTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0Nr7B/9XaAdcoGg1FbcNeKrQN88VqGX8pU4W
hcVMP4XdMxuBPmp/Rbkdkogvl8//MBGzn7jWnZBU59xkLnB0PfNB/JB5VdOrqT6w
k+TdPNbs7s7cxTYubRBguhhEmC85gu2hiNCl+zlurPNBqHIhXXSVq+dNqlw4g4zI
0cm0bTxSCLOppoBPXQXFxa4fAXopNPWeAF7Cg8+oMl6er8p7iILkxFK31JuafKjZ
95RU0ikdmPHhV3OXrcE914hXnhFBM2VQ56z9BI84pwNONdRwWd10wRkoQ7zj4WDN
qvNFY8mU/Bg6rHLI4Z2Ksj3zkLQs7VKBgdUL2dGPC/l3WElfFtF0sVkk
=FBMj
-----END PGP SIGNATURE-----
Merge tag 'regmap-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"After several quiet kernel releases we've got a couple of new features
in regmap, support for using hwspinlocks as the lock for the internal
data structures and a helper for polling on regmap_fields. The Kconfig
dependencies on hwspinlocks were annoyingly difficult to squash
between things behaving surprisingly and randconfig, I could've
squashed those commits down but might've have caused hassle with other
trees trying to use the new support.
- support for using a hwspinlock to protect the regmap
- an iopoll style helper for regmap_field"
* tag 'regmap-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Fix unused warning
regmap: Try to work around Kconfig exploding on HWSPINLOCK
regmap: Clean up hwspinlock on regmap exit
regmap: Also protect hwspinlock in error handling path
regmap: Add a config option for hwspinlock
regmap: Add hardware spinlock support
regmap: avoid -Wint-in-bool-context warning
regmap: add iopoll-like polling macro for regmap_field
regmap: constify regmap_bus structures
regmap: Avoid namespace collision within macro & tidy up
This patch fixes the warning of label 'err_map' defined but not used.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trying to work with hwspinlock from built in code is painful as it can
be built modular. Invert the test for REGMAP_HWSPINLOCK for now so we
end up requiring users to depend on HWSPINLOCK=y in order to turn on the
hwspinlock code.
Signed-off-by: Mark Brown <broonie@kernel.org>
The previous patch to allow the hwspinlock code to be disabled missed
handling the free in the error path, do so using the better IS_ENABLED()
pattern as suggested by Baolin. While we're at it also check that we have
a hardware spinlock before freeing it - the core code reports an error
when freeing an invalid lock.
Suggested-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Unlike other lock types hwspinlocks are optional and can be built
modular so we can't use them unconditionally in regmap so add a config
option that drivers that want to use hwspinlocks with regmap can select
which will ensure that hwspinlock is built in.
Signed-off-by: Mark Brown <broonie@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some platforms, when reading or writing some special registers through
regmap, we should acquire one hardware spinlock to synchronize between
the multiple subsystems. Thus this patch adds the hardware spinlock
support for regmap.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
These regmap_bus structures are only passed as the second argument to
__devm_regmap_init or __regmap_init, both of which are const, so the
regmap_bus structures can be const too.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: cc5d0db390 ("regmap: Add 1-Wire bus support")
Commit de0d6dbdbd ("w1: Add subsystem kernel public interface")
Fix place off w1.h header file
Cosmetic: Fix company name (local to international)
Signed-off-by: Alex A. Mihaylov <minimumlaw@rambler.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some irq controllers have writeonly/multipurpose register layouts. In
those cases we read invalid data back. Here we add the option
mask_writeonly as masking option.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The change makes possible to use regmap-irq interface within drivers
of simple interrupt controllers, which don't have an option to handle
different interrupt types and thus have one cell interrupt controllers
described in device tree bindings.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 2cbbb579bc ("regmap: Add the LZO cache support") added support
for LZO compression in regcache, but there were never any users added
afterwards. Since LZO support itself has its own size, it currently is
rather a deoptimization.
So make it optional by introducing a symbol that can be selected by
drivers wanting to make use of it.
Saves e.g. ~46 kB on MIPS (size of LZO support + regcache LZO code).
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
YueHaibing