Many integrated QCA9984 WiFis in various IPQ806x platform routers
from various vendors (Netgear R7800, ZyXEL NBG6817, TP-LINK C2600,
etc.) have either blank, bogus or non-unique MAC-addresses in
their calibration data.
As a result, OpenWrt utilizes a discouraged binary calibration data
patching method that allows to modify the device's MAC-addresses right
at the source. This is because the ath10k' firmware extracts the MAC
address from the supplied radio/calibration data and issues a response
to the ath10k linux driver. Which was designed to take the main MAC in
ath10k_wmi_event_ready().
Part of the "setting an alternate MAC" issue was already tackled by a
patch from Brian Norris:
commit 9d5804662c
("ath10k: retrieve MAC address from system firmware if provided")
by allowing the option to specify an alternate MAC-address with the
established device_get_mac_address() function which extracts the right
address from DeviceTree/fwnode mac-address or local-mac-address
properties and saves it for later.
However, Ben Greear noted that the Qualcomm's ath10k firmware is liable
to not properly calculate its rx-bssid mask in this case. This can cause
issues in the popluar "multiple AP with a single ath10k instance"
configurations.
To improve MAC address handling, Felix Fietkau suggested to call
pdev_set_base_macaddr_cmdid before bringing up the first vif and
use the first vif MAC address there. Which is in ath10k_core_start().
This patch implement Felix Fietkau's request to
"call pdev_set_base_macaddr_cmdid before bringing up the first vif".
The pdev_set_base_macaddr_cmdid is already declared for all devices
and version. The driver just needed the support code for this
function.
Tested on:
QCA9880/CUS223, firmwares: 10.2.4.13-2, 10.2.4.70.44, 10.2.4-1.0-00041
QCA9887/MR33 firmware:10.2.4-1.0-00033
QCA4019/RT-AC58U firmware: 10.4-3.4-00104, 10.4-3.5.3-00057
QCA9984/R7800 firmware: Candela Technologies (CT) Firmware
BugLink: https://lists.openwrt.org/pipermail/openwrt-devel/2018-November/014595.html
Fixes: 9d5804662c ("ath10k: retrieve MAC address from system firmware if provided")
Cc: Brian Norris <briannorris@chromium.org>
Cc: Ben Greear <greearb@candelatech.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TLV based firmware ex. QCA6174, WCN3990 expects key cipher value
set to 9 while non-TLV firmware expects key cipher value set to 8
for enabling GCMP and GCMP-256 cipher suites.
To fix this problem, attach the key cipher suite values based on
wmi version.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Hostapd uses CCMP, GCMP & GCMP-256 as 'wpa_pairwise' option to run WPA3.
In WCN3990 firmware cipher suite numbers 9 to 11 are for CCMP,
GCMP & GCMP-256.
To enable CCMP, GCMP & GCMP-256 cipher suites in WCN3990 firmware,
host sets 'n_cipher_suites = 11' while initializing hardware parameters.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The series "[PATCH 0/2] mt76x0: initialize per-channel max_power" depends on
commit d04ca38386 ("mt76x0u: fix suspend/resume"), so merge wireless-drivers
into wireless-drivers-next to get that.
ath.git patches for 5.1. Major changes:
ath10k
* change QMI interface to support the new (and backwards incompatible)
interface from HL3.1 and used in recent HL2.0 branch firmware releases
ath
* add new country codes for US
This patch adds several country codes to the regd.h and regd_common.h
files in order to support devices like the Linksys EA6350v3, whose
country codes are not present in the original list. Without this patch,
all devices whose manufacturer programmed any of these code in their
EEPROM will not work.
The values for CTRY_UNITED_STATES2 and CTRY_UNITED_STATES3 were taken
from a post by Sven Eckelmann <sven.eckelmann@openmesh.com>:
<http://lists.infradead.org/pipermail/ath10k/2017-August/010014.html>
Signed-off-by: Oever Gonzalez <notengobattery@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
as you are already in a tasklet, it is unnecessary to call
spin_lock_bh, because softirq already disable BH.
Signed-off-by: Zhiwei Jiang <qq282012236@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, they can now return error values if
something went wrong. If that happens, return a NULL as a *dentry to
the relay core instead of passing it an illegal pointer.
The relay core should be able to handle an illegal pointer, but add this
check to be safe.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware sends the tx_duration for each in HTT_T2H_MSG_TYPE_PEER_STATS
msg. Fill the tx_duration sent by firmware in the tx stats information
per STA.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1,
WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware advertises the LDPC support information for HT in
HT capability info in the wmi service ready event. To provide
granularity, firmware now advertises WMI_HT_CAP_RX_LDPC and
WMI_HT_CAP_TX_LDPC separately. To support LDPC, host should
also check for WMI_HT_CAP_RX_LDPC and WMI_HT_CAP_TX_LDPC in HT
capabilities.
Add a condition to existing logic in host to know whether firmware
supports LDPC or not.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1,
WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reduce the transmit MSDU count for SDIO, to match with the descriptors
as used by the firmware. This also acts as a high watermark level for
transmit. Too many packets to the firmware results in transmit overflow
interrupt.
It only affect SDIO chip, it will not cause functionaly changes to
other hardware.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, they can now return error values if
something went wrong. If that happens, return a NULL as a *dentry to
the relay core instead of passing it an illegal pointer.
The relay core should be able to handle an illegal pointer, but add this
check to be safe.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: ath10k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath10k/snoc.c: In function 'ath10k_snoc_tx_pipe_cleanup':
drivers/net/wireless/ath/ath10k/snoc.c:681:22: warning:
variable 'ar_snoc' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
sdio_register_driver() doesn't do this for us, unlike (for example)
platform_driver_register(). This is important for helping track
module-to-device relationships.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The swap box flag of firmware is not set before htc ready, then it
will not set swap box flag in ath10k driver, and it will let swap
box setting not same between firmware and ath10k driver, then it
will trigger firmware assert failure.
Check the flag and set swap box after htc ready will fix the firmware
assert failure.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The hw-restart crash inject mode is a special mode, where
there is no crash generated in the firmware, but instead
the driver restarts the firmware. In order to restart WCN3990
firmware, the driver needs to send qmi_wlan_disable message
followed by the qmi_wlan_enable message to the WCN3990 firmware.
Currently the qmi_wlan_disable message is not sent to
the WCN3990 firmware when hw-restart crash is injected,
which causes the firmware to crash when the driver sends
qmi_wlan_enable message during ath10k_restart.
Send qmi_wlan_disable to the WCN3990 firmware when the
hw-restart crash is injected via debugfs.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The management frames transmitted are dma mapped with
direction TO_DEVICE, but incorrectly mapped with
direction FROM_DEVICE during tx complete and error cases.
Fix the direction of dma during dma unmap of the
transmitted management frames.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Fixes: 38a1390e02 ("ath10k: dma unmap mgmt tx buffer if wmi cmd send fails")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 sends tx completion of multiple management
frames bundled together in a single event, if the
host driver exposes the support to handle this
bundled tx completion event. This reduces the number
of WMI events which are sent to the host driver by
the target.
Set the BUNDLE_TX_COMPL flag in the host capability
flags when host sends the wmi init command, to indicate
the host capability to handle bundled tx completion for
management frames.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 supports sending tx completion for multiple
management frames bundled together in a single event.
Add support to handle the bundled tx completion
event for WCN3990.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HOST capability interface data structures are updated
in HL3.1 fw version. Update the qmi host capability
members for compatibility across different firmware
versions.
Since this change breaks backward compatibility with
HL2.0 fw, HL2.0 fw upgrade to WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
or later version is required.
Testing:
Tested on QCS404 platform(WCN3990 HW).
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1,
WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 5.1. Lots of new features in various drivers
but nothing really special standing out.
Major changes:
brcmfmac
* DMI nvram filename quirk for PoV TAB-P1006W-232 tablet
rsi
* support for hardware scan offload
iwlwifi
* support for Target Wakeup Time (TWT) -- a feature that allows the AP
to specify when individual stations can access the medium
* support for mac80211 AMSDU handling
* some new PCI IDs
* relicense the pcie submodule to dual GPL/BSD
* reworked the TOF/CSI (channel estimation matrix) implementation
* Some product name updates in the human-readable strings
mt76
* energy detect regulatory compliance fixes
* preparation for MT7603 support
* channel switch announcement support
mwifiex
* support for sd8977 chipset
qtnfmac
* support for 4addr mode
* convert to SPDX license identifiers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcWoRZAAoJEG4XJFUm622bOm4H/j2Tt6qS5yz3ioH2I7R+f7e/
8C2JJia+uQs8iChdyCjCFcDymmjB2l5u72JvupwCdERzp3okv/xmJiLW5wFW2z4x
B3Nrd4FV2EMIdsRXg1RWbwZHC4wIY6lFhL1OcUcuNwpb5ab1ppvQFHmH5logd7DC
euFSe02g8xmXdUMciRDKGUdiSiDIApmx9dUfguaqYtepqeW3hmDEEkeDicaf2fjq
cM5qAvssIAgUTqwIImEQQEU7j7A2TgMYkRBNzwv2QG47jy6OlgXkZVByvtq59irg
v4BFNtG6uRWTugxQ/FwYWeqsrnjegFNKm5MFbS6BDxbe05M7QzeK8zm55fE9ZGk=
=cHbd
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-02-06' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.1
First set of patches for 5.1. Lots of new features in various drivers
but nothing really special standing out.
Major changes:
brcmfmac
* DMI nvram filename quirk for PoV TAB-P1006W-232 tablet
rsi
* support for hardware scan offload
iwlwifi
* support for Target Wakeup Time (TWT) -- a feature that allows the AP
to specify when individual stations can access the medium
* support for mac80211 AMSDU handling
* some new PCI IDs
* relicense the pcie submodule to dual GPL/BSD
* reworked the TOF/CSI (channel estimation matrix) implementation
* Some product name updates in the human-readable strings
mt76
* energy detect regulatory compliance fixes
* preparation for MT7603 support
* channel switch announcement support
mwifiex
* support for sd8977 chipset
qtnfmac
* support for 4addr mode
* convert to SPDX license identifiers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Change snprintf to scnprintf. There are generally two cases where using
snprintf causes problems.
1) Uses of size += snprintf(buf, SIZE - size, fmt, ...) In this case,
if snprintf would have written more characters than what the buffer
size (SIZE) is, then size will end up larger than SIZE. In later uses
of snprintf, SIZE - size will result in a negative number, leading to
problems. Note that size might already be too large by using size =
snprintf before the code reaches a case of size += snprintf.
2) If size is ultimately used as a length parameter for a copy back to
user space, then it will potentially allow for a buffer overflow and
information disclosure when size is greater than SIZE. When the size is
used to index the buffer directly, we can have memory corruption. This
also means when size = snprintf... is used, it may also cause problems
since size may become large. Copying to userspace is mitigated by the
HARDENED_USERCOPY kernel configuration.
The solution to these issues is to use scnprintf which returns the number
of characters actually written to the buffer, so the size variable will
never exceed SIZE.
Cc: Willy Tarreau <w@1wt.eu>
Cc: Silvio Cesare <silvio.cesare@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HTT aggr message parameter in HL2.0 fw are different in comparison
to legacy fw version. Fill correct HTT aggr msg parameter for
targets using HL2.0 firmware.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After system entering S5 (shut down but system still
providing power to QCA9377) on Ubuntu platform, power
consumption of QCA9377 is 69mA, which is too high.
The root cause is pci_soft_reset is not set for QCA9377
during pci probe.
To fix this issue, set 'pci_soft_reset' to 'th10k_pci_warm_reset',
and then the power consumption drops to a normal value(10mA).
Verified on Dell Ubuntu platform with firmware:
WLAN.TF.1.0-00002-QCATFSWPZ-5
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 is a 37-bit target but can address memory range
only upto 35 bits. The 36th bit is used to control the
smmu/iommu translation and the 37th bit is used by the
internal bus masters to access the wifi subsystem internal
SRAM. With the DMA mask set to 37i-bit, the host driver
can get 37-bit dma address, which leads to incorrect
address access in the target.
Hence the host driver can used addresses upto 35-bit
for WCN3990. Fix the dma mask for wcn3990 to 35-bit,
instead of 37-bit.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 is SNOC, not PCI. This prevents probing WCN3990.
Fixes: 367c899f62 ("ath10k: add bus type check in ath10k_init_hw_params")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath6kl_wmi_cmd_send could fail, so let's return its error code upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath9k_of_init() function[0] was initially written on the assumption that
if someone had an explicit ath9k OF node that "there must be something
wrong, why would someone add an OF node if everything is fine"[1]
(Quoting Martin Blumenstingl <martin.blumenstingl@googlemail.com>)
"it turns out it's not that simple. with your requirements I'm now aware
of two use-cases where the current code in ath9k_of_init() doesn't work
without modifications"[1]
The "your requirements" Martin speaks of is the result of the fact that I
have a device (PowerCloud Systems CR5000) has some kind of default - not
unique mac address - set and requires to set the correct MAC address via
mac-address devicetree property, however:
"some cards come with a physical EEPROM chip [or OTP] so "qca,no-eeprom"
should not be set (your use-case). in this case AH_USE_EEPROM should be
set (which is the default when there is no OF node)"[1]
The other use case is:
the firmware on some PowerMac G5 seems to add a OF node for the ath9k
card automatically. depending on the EEPROM on the card AH_NO_EEP_SWAP
should be unset (which is the default when there is no OF node). see [3]
After this patch to ath9k_of_init() the new behavior will be:
if there's no OF node then everything is the same as before
if there's an empty OF node then ath9k will use the hardware EEPROM
(before ath9k would fail to initialize because no EEPROM data was
provided by userspace)
if there's an OF node with only a MAC address then ath9k will use
the MAC address and the hardware EEPROM (see the case above)
with "qca,no-eeprom" EEPROM data from userspace will be requested.
the behavior here will not change
[1]
Martin provides additional background on EEPROM swapping[1].
Thanks to Christian Lamparter <chunkeey@gmail.com> for all his help on
troubleshooting this issue and the basis for this patch.
[0]https://elixir.bootlin.com/linux/v4.20-rc7/source/drivers/net/wireless/ath/ath9k/init.c#L615
[1]https://github.com/openwrt/openwrt/pull/1645#issuecomment-448027058
[2]https://github.com/openwrt/openwrt/pull/1613
[3]https://patchwork.kernel.org/patch/10241731/
Fixes: 138b41253d ("ath9k: parse the device configuration from an OF node")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
-----BEGIN PGP SIGNATURE-----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=TRdW
-----END PGP SIGNATURE-----
Merge tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"This is the main pull request for block/storage for 4.21.
Larger than usual, it was a busy round with lots of goodies queued up.
Most notable is the removal of the old IO stack, which has been a long
time coming. No new features for a while, everything coming in this
week has all been fixes for things that were previously merged.
This contains:
- Use atomic counters instead of semaphores for mtip32xx (Arnd)
- Cleanup of the mtip32xx request setup (Christoph)
- Fix for circular locking dependency in loop (Jan, Tetsuo)
- bcache (Coly, Guoju, Shenghui)
* Optimizations for writeback caching
* Various fixes and improvements
- nvme (Chaitanya, Christoph, Sagi, Jay, me, Keith)
* host and target support for NVMe over TCP
* Error log page support
* Support for separate read/write/poll queues
* Much improved polling
* discard OOM fallback
* Tracepoint improvements
- lightnvm (Hans, Hua, Igor, Matias, Javier)
* Igor added packed metadata to pblk. Now drives without metadata
per LBA can be used as well.
* Fix from Geert on uninitialized value on chunk metadata reads.
* Fixes from Hans and Javier to pblk recovery and write path.
* Fix from Hua Su to fix a race condition in the pblk recovery
code.
* Scan optimization added to pblk recovery from Zhoujie.
* Small geometry cleanup from me.
- Conversion of the last few drivers that used the legacy path to
blk-mq (me)
- Removal of legacy IO path in SCSI (me, Christoph)
- Removal of legacy IO stack and schedulers (me)
- Support for much better polling, now without interrupts at all.
blk-mq adds support for multiple queue maps, which enables us to
have a map per type. This in turn enables nvme to have separate
completion queues for polling, which can then be interrupt-less.
Also means we're ready for async polled IO, which is hopefully
coming in the next release.
- Killing of (now) unused block exports (Christoph)
- Unification of the blk-rq-qos and blk-wbt wait handling (Josef)
- Support for zoned testing with null_blk (Masato)
- sx8 conversion to per-host tag sets (Christoph)
- IO priority improvements (Damien)
- mq-deadline zoned fix (Damien)
- Ref count blkcg series (Dennis)
- Lots of blk-mq improvements and speedups (me)
- sbitmap scalability improvements (me)
- Make core inflight IO accounting per-cpu (Mikulas)
- Export timeout setting in sysfs (Weiping)
- Cleanup the direct issue path (Jianchao)
- Export blk-wbt internals in block debugfs for easier debugging
(Ming)
- Lots of other fixes and improvements"
* tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block: (364 commits)
kyber: use sbitmap add_wait_queue/list_del wait helpers
sbitmap: add helpers for add/del wait queue handling
block: save irq state in blkg_lookup_create()
dm: don't reuse bio for flushes
nvme-pci: trace SQ status on completions
nvme-rdma: implement polling queue map
nvme-fabrics: allow user to pass in nr_poll_queues
nvme-fabrics: allow nvmf_connect_io_queue to poll
nvme-core: optionally poll sync commands
block: make request_to_qc_t public
nvme-tcp: fix spelling mistake "attepmpt" -> "attempt"
nvme-tcp: fix endianess annotations
nvmet-tcp: fix endianess annotations
nvme-pci: refactor nvme_poll_irqdisable to make sparse happy
nvme-pci: only set nr_maps to 2 if poll queues are supported
nvmet: use a macro for default error location
nvmet: fix comparison of a u16 with -1
blk-mq: enable IO poll if .nr_queues of type poll > 0
blk-mq: change blk_mq_queue_busy() to blk_mq_queue_inflight()
blk-mq: skip zero-queue maps in blk_mq_map_swqueue
...
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcG9TEAAoJEG4XJFUm622byW8H/1vMVJhXwgIZbHeoUKNa47Yp
Z7Jv5vW8IGXu+lp7DyoedDCbq4+lskNSlDV1DmysNChLgDnApU/3oCd/jH8EiGPV
JAFUHb85HuVLTTpPpNHtnYz3IzL7r098TNVxOU0VD+xILM0Mf0aCeXztgmFWpGaY
/rfHkId8oKUezIjdu6Dc96mqITrT6WRNtnOMfjr6dZPjClRTS44Hyz3Ga3rXABBL
/n8BCkl0GpKGrL3mBy2CCR5mVY8zfxMB4Aj2zx7bccZ8i2i2QjrGlXCHyB6ImNrR
lv4L1fUVXZWVdeOe8EbpftY7zEsPrX+XNm6h1kckdB7UyuBROpQLsVb+yxlLh9g=
=mhAw
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-12-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wmi configuration cmd to configure base band(BB) power amplifier(PA)
off timing values in hardware. The default PA off timings were fine tuned
to make proper DFS radar detection in QCA reference design. If ODM uses
different PA in their design, then the same default PA off timing values
cannot be used, it requires different settling time to detect radar pulses
very sooner and avoid radar detection problems. In that case it provides
provision to select proper PA off timing values based on the PA hardware used.
The PA component is part of FEM hardware and new device tree entry
"ext-fem-name" is used to indentify the FEM hardware. And this wmi configuration
cmd is enabled via wmi service flag "WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT".
Other way is to apply these values through calibration data, but recalibration
of all boards out there might not be feasible.
This change tested on firmware ver 10.2.4-1.0-00042 in QCA988X chipset.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Memory of tx_stats was allocated when a STA was added. But it's not freed
if the STA failed to be added to driver. This issue could be seen in MDK3
attack case when STA number reached the limit.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There was a race condition in SMP that an ath10k_peer was created but its
member sta was null. Following are procedures of ath10k_peer creation and
member sta access in peer statistics path.
1. Peer creation:
ath10k_peer_create()
=>ath10k_wmi_peer_create()
=>ath10k_wait_for_peer_created()
...
# another kernel path, RX from firmware
ath10k_htt_t2h_msg_handler()
=>ath10k_peer_map_event()
=>wake_up()
# ar->peer_map[id] = peer //add peer to map
#wake up original path from waiting
...
# peer->sta = sta //sta assignment
2. RX path of statistics
ath10k_htt_t2h_msg_handler()
=>ath10k_update_per_peer_tx_stats()
=>ath10k_htt_fetch_peer_stats()
# peer->sta //sta accessing
Any access of peer->sta after peer was added to peer_map but before sta was
assigned could cause a null pointer issue. And because these two steps are
asynchronous, no proper lock can protect them. So both peer and sta need to
be checked before access.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The "survey" pointer is the address of an array element. We know that
it can't be NULL so this check can be removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During driver load below warn logs are printed in the console.
Since driver may not implement all wmi events sent by fw and
all of them are non-fatal, move this log to debug level to
remove un-necessary warn message on console.
[ 361.887230] ath10k_snoc a000000.wifi: Unknown eventid: 16393
[ 361.907037] ath10k_snoc a000000.wifi: Unknown eventid: 237569
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The devm_memremap() function doesn't return NULLs, it returns error
pointers.
Fixes: ba94c753cc ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All the necessary patches to make wifi running (over SNOC)
are merged and tested on SDM845/QCS404 platform with WCN3990
wifi module, hence remove work in progress debug from snoc
driver and Kconfig.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some hardwares variants (QCA99x0) are limiting msdu deaggregation with
some threshold value(default limit in QCA99x0 is 64 msdus), it was introduced to
avoid excessive MSDU-deaggregation in error cases. When number of sub frames
exceeds the limit, target hardware will send all msdus starting from present
msdu in RAW format as a single msdu packet and it will be indicated with
error status bit "RX_MSDU_END_INFO0_MSDU_LIMIT_ERR" set in rx descriptor.
This msdu frame is a partial raw MSDU and does't have first msdu and ieee80211
header. It caused below warning message.
[ 320.151332] ------------[ cut here ]------------
[ 320.155006] WARNING: CPU: 0 PID: 3 at drivers/net/wireless/ath/ath10k/htt_rx.c:1188
In our issue case, MSDU limit error happened due to FCS error and generated
this warning message.
This fixes the warning by handling the MSDU limit error. If msdu limit error
happens, driver adds first MSDU's ieee80211 header and sets A-MSDU present bit
in QOS header so that upper layer processes this frame if it is valid or drop it
if FCS error set. And removed the warning message, hence partial msdus without
first msdu is expected in msdu limit error cases.
Tested on QCA9984, Firmware 10.4-3.6-00104
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently in 10.4 FW, all the received 4addr frames are processed for
source port learning which is enabled by default. This learning can't be
disabled by default in FW since it breaks backward compatibility.
Since ath10k uses mac80211 based 4addr mode, source port learning done in
10.4 FW is redundant and also causes issues when 3addr frames are
transmitted/received for a 4addr station.
One such visible functional impact is when GTK rekey frame from
hostapd based AP to 4addr STA is dropped in AP's 10.4 FW. This is since
GTK rekey EAPOL frame is 3addr frame on AP interface and STA enabled
with 4addr is already allowed for receiving 3addr EAPOL frames.
Source port learning implementation in 10.4 FW drops this 3addr GTK rekey
frame in AP destinated for 4addr STA causing disassociation and
re-association for every GTK rekey session. GTK rekey issue is not seen
when learning is disabled in FW.
To prevent such issues without breaking backward compatibility, FW
advertises new service bit making the source port learning configurable and
this learning is being currently disabled during ath10k vdev creation.
* Tested HW: QCA9984
* Tested FW: 10.4-3.6.0.1-00004
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Mesh path metric needs tx rate information from ieee80211_tx_status()
call but in ath10k there is no mechanism to report tx rate information
via ieee80211_tx_status(), the tx rate is only accessible via
sta_statiscs() op.
Per peer tx stats has tx rate info available, Tx rate is available
to ath10k driver after every 4 PPDU sent in the air. For each PPDU,
ath10k driver updates rate informattion to mac80211 using
ieee80211_tx_rate_update().
Per peer txrate information is updated through per peer statistics
and is available for QCA9888/QCA9984/QCA4019/QCA998X only
Tested on QCA9984 with firmware-5.bin_10.4-3.5.3-00053
Tested on QCA998X with firmware-5.bin_10.2.4-1.0-00036
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When processing HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND, if the length of a msdu
is larger than the tailroom of the rx skb, skb_over_panic issue will happen
when calling skb_put. In monitor mode, amsdu will be handled in this path, and
msdu_len of the first msdu_desc is the length of the entire amsdu, which might
be larger than the maximum length of a skb, in such case, it will hit the issue
upon.
To fix this issue, process msdu list separately for monitor mode.
Successfully tested with:
QCA6174 (FW version: RM.4.4.1.c2-00057-QCARMSWP-1).
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
[kvalo@codeaurora.org: cosmetic cleanup]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This issue arise in a race condition between ath10k_sta_state() and
ath10k_htt_fetch_peer_stats(), explained in below scenario
Steps:
1. In ath10k_sta_state(), arsta->tx_stats get deallocated before peer deletion
when the station moves from IEEE80211_STA_NONE to IEEE80211_STA_NOTEXIST
state.
2. Meanwhile ath10k receive HTT_T2H_MSG_TYPE_PEER_STATS message.
In ath10k_htt_fetch_peer_stats(), arsta->tx_stats get accessed after
the peer validation check.
Since arsta->tx_stats get freed before the peer deletion [1].
ath10k_htt_fetch_peer_stats() ended up in "use after free" situation.
Fixed this issue by moving the arsta->tx_stats free handling after the
peer deletion. so that ath10k_htt_fetch_peer_stats() will not end up in
"use after free" situation.
Kernel Panic:
Unable to handle kernel NULL pointer dereference at virtual address 00000286
pgd = d8754000
[00000286] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
...
CPU: 0 PID: 6245 Comm: hostapd Not tainted
task: dc44cac0 ti: d4a38000 task.ti: d4a38000
PC is at kmem_cache_alloc+0x7c/0x114
LR is at ath10k_sta_state+0x190/0xd58 [ath10k_core]
pc : [<c02bdc50>] lr : [<bf916b78>] psr: 20000013
sp : d4a39b88 ip : 00000000 fp : 00000001
r10: 00000000 r9 : 1d3bc000 r8 : 00000dc0
r7 : 000080d0 r6 : d4a38000 r5 : dd401b00 r4 : 00000286
r3 : 00000000 r2 : d4a39ba0 r1 : 000080d0 r0 : dd401b00
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5787d Table: 5a75406a DAC: 00000015
Process hostapd (pid: 6245, stack limit = 0xd4a38238)
Stack: (0xd4a39b88 to 0xd4a3a000)
...
[<c02bdc50>] (kmem_cache_alloc) from [<bf916b78>] (ath10k_sta_state+0x190/0xd58 [ath10k_core])
[<bf916b78>] (ath10k_sta_state [ath10k_core]) from [<bf870d4c>] (sta_info_insert_rcu+0x418/0x61c [mac80211])
[<bf870d4c>] (sta_info_insert_rcu [mac80211]) from [<bf88634c>] (ieee80211_add_station+0xf0/0x134 [mac80211])
[<bf88634c>] (ieee80211_add_station [mac80211]) from [<bf83f3c4>] (nl80211_new_station+0x330/0x36c [cfg80211])
[<bf83f3c4>] (nl80211_new_station [cfg80211]) from [<bf6c4040>] (extack_doit+0x2c/0x74 [compat])
[<bf6c4040>] (extack_doit [compat]) from [<c05c285c>] (genl_rcv_msg+0x274/0x30c)
[<c05c285c>] (genl_rcv_msg) from [<c05c1d98>] (netlink_rcv_skb+0x58/0xac)
[<c05c1d98>] (netlink_rcv_skb) from [<c05c25d4>] (genl_rcv+0x20/0x34)
[<c05c25d4>] (genl_rcv) from [<c05c1750>] (netlink_unicast+0x11c/0x204)
[<c05c1750>] (netlink_unicast) from [<c05c1be0>] (netlink_sendmsg+0x30c/0x370)
[<c05c1be0>] (netlink_sendmsg) from [<c0587e90>] (sock_sendmsg+0x70/0x84)
[<c0587e90>] (sock_sendmsg) from [<c058970c>] (___sys_sendmsg.part.3+0x188/0x228)
[<c058970c>] (___sys_sendmsg.part.3) from [<c058a594>] (__sys_sendmsg+0x4c/0x70)
[<c058a594>] (__sys_sendmsg) from [<c0208c80>] (ret_fast_syscall+0x0/0x44)
Code: ebfffec1 e1a04000 ea00001b e5953014 (e7940003)
ath10k_pci 0000:01:00.0: SWBA overrun on vdev 0, skipped old beacon
Hardware tested: QCA9984
Firmware tested: 10.4-3.6.0.1-00004
Fixes: a904417fc ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath10k/mac.c: In function 'ath10k_sta_state':
drivers/net/wireless/ath/ath10k/mac.c:6238:7: warning:
variable 'num_tdls_vifs' set but not used [-Wunused-but-set-variable]
'num_tdls_vifs' not used any more after
9a993cc1ea ("ath10k: fix the logic of limiting tdls peer counts")
Also, remove the single called function ath10k_mac_tdls_vifs_count
and ath10k_mac_tdls_vifs_count_iter.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/wil6210/main.c: In function '_wil6210_disconnect':
drivers/net/wireless/ath/wil6210/main.c:407:23: warning:
variable 'wdev' set but not used [-Wunused-but-set-variable]
It never used since commit ("e1b43407c034 wil6210: refactor disconnect flow")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is not an unexpected condition, so we don't need to be shouting to the
world about it.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When ath6kl was reworked to share code between regular and scheduled scans
in commit 3b8ffc6a22 ("ath6kl: Configure probed SSID list consistently"),
probed SSID entry changed from 1-index to 0-indexed. However,
ath6kl_cfg80211_scan_complete_event() was missed in that change. Fix its
indexing so that we correctly clear out the probed SSID list.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit dd45b7598f ("ath6kl: Include match ssid list in scheduled scan")
merged the probed and matched SSID lists before sending them to the
firmware. In the process, it assumed match set support is always available
in ath6kl_set_probed_ssids, which breaks scans for hidden SSIDs. Now, check
that the firmware supports matching SSIDs in scheduled scans before setting
MATCH_SSID_FLAG.
Fixes: dd45b7598f ("ath6kl: Include match ssid list in scheduled scan")
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HL2.0 firmware does not support setting quiet mode. If the host driver sends
the quiet mode setting command to the HL2.0 firmware, it crashes with the below
signature.
fatal error received: err_qdi.c:456:EX:wlan_process:1:WLAN RT:207a:PC=b001b4f0
The quiet mode command support is exposed by the firmware via thermal throttle
wmi service. Enable ath10k thermal support if thermal throttle wmi service bit
is set. 10.x firmware versions support this feature by default, but
unfortunately do not advertise the support via service flags, hence have to
manually set the service flag in ath10k_core_compat_services().
Tested on QCA988X with 10.2.4.70.9-2. Also tested on WCN3990.
Co-developed-by: Govind Singh <govinds@codeaurora.org>
Co-developed-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Prevent a namespace conflict as in following patches as skbuff.h will
include the crypto API.
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sagi Grimberg <sagi@lightbitslabs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
First set of patches for 4.21. Most notable here is support for
Quantenna's QSR1000/QSR2000 chipsets and more flexible ways to provide
nvram files for brcmfmac.
Major changes:
brcmfmac
* add support for first trying to get a board specific nvram file
* add support for getting nvram contents from EFI variables
qtnfmac
* use single PCIe driver for all platforms and rename
Kconfig option CONFIG_QTNFMAC_PEARL_PCIE to CONFIG_QTNFMAC_PCIE
* add support for QSR1000/QSR2000 (Topaz) family of chipsets
ath10k
* add support for WCN3990 firmware crash recovery
* add firmware memory dump support for QCA4019
wil6210
* add firmware error recovery while in AP mode
ath9k
* remove experimental notice from dynack feature
iwlwifi
* PCI IDs for some new 9000-series cards
* improve antenna usage on connection problems
* new firmware debugging infrastructure
* some more work on 802.11ax
* improve support for multiple RF modules with 22000 devices
cordic
* move cordic macros and defines to a public header file
* convert brcmsmac and b43 to fully use cordic library
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcATmGAAoJEG4XJFUm622bk9kH/1RWa2z7Gmjr2wBSLHryvRAH
3FAUSJ4GJPH6MJ5X824srkcVsx2Y1RVt2i+bLXRXLq35aZkrFswohTXVM2h5dU7T
Uy2SL+q9pBUcS7fyv9bE7XV7KsFBJly/5p/wciVRZMnEK6X/w6KkBx/vGvlm5I/C
q196KazbVAYcl6s7KMrfFOYt0Wsto/gdEeesSVBkmcCTEkiKUjjJ4WEDVvAKK+qB
AiwgSdioqYmmEiUuredm6bhVqZG3K2mScoCy95N3jXkiDaKkaYgVtBuAU4Cdju/t
WgLIc9EnUYxXZtwnt889X62P1OkDOtKlj/mjdsGyF0Vrs1W+kErDO0NocOvu2Tk=
=9bL7
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-11-30' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
First set of patches for 4.21. Most notable here is support for
Quantenna's QSR1000/QSR2000 chipsets and more flexible ways to provide
nvram files for brcmfmac.
Major changes:
brcmfmac
* add support for first trying to get a board specific nvram file
* add support for getting nvram contents from EFI variables
qtnfmac
* use single PCIe driver for all platforms and rename
Kconfig option CONFIG_QTNFMAC_PEARL_PCIE to CONFIG_QTNFMAC_PCIE
* add support for QSR1000/QSR2000 (Topaz) family of chipsets
ath10k
* add support for WCN3990 firmware crash recovery
* add firmware memory dump support for QCA4019
wil6210
* add firmware error recovery while in AP mode
ath9k
* remove experimental notice from dynack feature
iwlwifi
* PCI IDs for some new 9000-series cards
* improve antenna usage on connection problems
* new firmware debugging infrastructure
* some more work on 802.11ax
* improve support for multiple RF modules with 22000 devices
cordic
* move cordic macros and defines to a public header file
* convert brcmsmac and b43 to fully use cordic library
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211 may call us with vif == NULL, if the station is not currently
active (e.g., not associated). It is trivially easy to reproduce a crash
by suspending the system when not connected to an AP:
[ 65.533934] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
...
[ 65.574521] pc : ath10k_flush+0x30/0xd0 [ath10k_core]
[ 65.574538] lr : __ieee80211_flush_queues+0x180/0x244 [mac80211]
[ 65.599680] Process kworker/u12:1 (pid: 57, stack limit = 0x(____ptrval____))
[ 65.599682] Call trace:
[ 65.599695] ath10k_flush+0x30/0xd0 [ath10k_core]
[ 65.642064] __ieee80211_flush_queues+0x180/0x244 [mac80211]
[ 65.642079] ieee80211_flush_queues+0x34/0x40 [mac80211]
[ 65.642095] __ieee80211_suspend+0xfc/0x47c [mac80211]
[ 65.658611] ieee80211_suspend+0x30/0x3c [mac80211]
[ 65.658627] wiphy_suspend+0x15c/0x3a8 [cfg80211]
[ 65.672810] dpm_run_callback+0xf0/0x1f0
[ 65.672814] __device_suspend+0x3ac/0x4f8
[ 65.672819] async_suspend+0x34/0xbc
[ 65.684096] async_run_entry_fn+0x54/0x104
[ 65.684099] worker_thread+0x4cc/0x72c
[ 65.684102] kthread+0x134/0x13c
[ 65.684105] ret_from_fork+0x10/0x18
Fixes: 9de4162f09 ("ath10k: add peer flush in ath10k_flush for STATION")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We tried to revert commit d9c52fd17c ("ath9k: fix tx99 with monitor
mode interface") but accidentally missed part of the locking change.
The lock has to be held earlier so that we're holding it when we do
"sc->tx99_vif = vif;" and also there in the current code there is a
stray unlock before we have taken the lock.
Fixes: 6df0580be8 ("ath9k: add back support for using active monitor interfaces for tx99")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove experimental tag from dynack Kconfig entry since it has
been tested on outdoor 25Km links
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to make propagation time estimation faster,
use current sample as ewma output value during 'late ack'
tracking
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Check da->enabled flag first in ath_dynack_sample_tx_ts and
ath_dynack_sample_ack_ts routines in order to avoid useless
processing
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move debug log in ath_dynack_sample_tx_ts and ath_dynack_sample_ack_ts
after timestamp buffer head/tail increments in order to make debugging
more user friendly
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to properly support dynack in ad-hoc mode running
wpa_supplicant, take into account authentication frames for
'late ack' detection. This patch has been tested on devices
mounted on offshore high-voltage stations connected through
~24Km link
Reported-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Not all devices using this driver are backed by a PCI device, so it's
not fair to assume 'to_pci_dev()' is valid. Fortunately, we only were
using this to convert straight back to a bare 'device', which means we
were only doing no-op pointer arithmetic, and not actually accessing
potentially out-of-bounds memory. But this is still bad practice.
Just use 'ar->dev' directly, since that's really all we're looking for.
Fixes: 209b2a68de ("ath10k: add platform regulatory domain support")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 2ea9f12cef ("ath10k: add new cipher suite support") added a new
n_cipher_suites HW param with a fallback value and a warning log. Commit
03a72288c5 ("ath10k: wmi: add hw params entry for wcn3990") later
added WCN3990 HW entries, but it missed the n_cipher_suites.
Rather than seeing this warning every boot
ath10k_snoc 18800000.wifi: invalid hw_params.n_cipher_suites 0
let's provide the appropriate value.
Cc: Rakesh Pillai <pillair@qti.qualcomm.com>
Cc: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
They're provided as callbacks in ath10k_hif_ops and should be accessed
that way, if needed outside of snoc.c, and anyway, they're currently
unused outside snoc.c.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Similar to regulator error handling, we should only start tearing down
the 'i - 1' clock when clock 'i' fails to enable. Otherwise, we might
end up with an unbalanced clock, where we never successfully enabled the
clock, but we try to disable it anyway.
Fixes: a6a793f987 ("ath10k: vote for hardware resources for WCN3990")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
I rarely see drivers specify precise voltage requirements like this, but
if we really have to...let's at least give a little wiggle room. Board
designs (and accompanying device trees) may not provide exactly the
voltage listed here, and we shouldn't fail to probe just because of
this.
Round these ranges down to the nearest volt, and provide a 0.05V margin.
The regulator should provide its own supported ranges, which will
helpfully intersect with these ranges.
I would just as well remove these ranges entirely, but if I understand
correctly, there's some reason that QCOM SoC's like to set zero /
non-zero voltages.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If a regulator fails to set its voltage, we end up with an unbalanced
call to regulator_disable(), because the error path starts with the
current regulator (which was never enabled).
Factor out the "on" function to perform (and unwind if failed) a single
regulator at a time, and then main loop (ath10k_snoc_vreg_on()) can just
worry about unwinding the regulators that were already enabled.
It also helps to factor out the "off" function, to avoid repeating some
code here.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_wcn3990_clk_info and ath10k_wcn3990_vreg_info are not
WCN3990-specific structures. They hold generic data. So don't name them
with wcn3990 specifics.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Switch from spin_lock to spin_lock_irqsave, because
wmi_ev_lock is used inside interrupt handler.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After being associated with some EDMA rx traffic, upon "down" driver
doesn't free all skbs in the rx ring.
Modify wil_move_all_rx_buff_to_free_list to loop on active list of rx
buffers, unmap the physical memory and free the skb.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rx buffers in EDMA mode are initialized to 4 bytes aligned size.
Remove the unnecessary alignment code applied on rx buffer size.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
RGF_CAF_ICR register location has changed in Talyn-MB.
Add RGF_CAF_ICR_TALYN_MB to support the new address.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
L2 RX status errors should not be treated as a bitmap and the actual
error values should be checked.
Print L2 errors as wil_err_ratelimited for easier debugging
when such errors occurs.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All wil6210 device memory access should be 4 bytes aligned. In io
blob wil6210 did not force alignment for read function, this caused
alignment fault on some platforms.
Fixing that by accessing all 4 lower bytes and return to host the
requested data.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Initialize unset variable, and verify that mid is valid.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wil6210 used to notify cfg80211_del_sta on every fw disconnect event.
In disable_ap_sme mode the userspace manages the protocol SME and
FW sends disconnect event only due to link loss.
In disable_ap_sme mode, indicate CQM packet loss to let the host
control the connection and disconnect the link if needed.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Separate sending command to the fw from the event handling function to
simplify the disconnect flow and track the from_event flag correctly.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A successful call to wil_tx_ring takes skb reference so
it will only be freed in wil_tx_complete. Consume the skb
in wil_find_tx_bcast_2 to prevent memory leak.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AP configuration is stored by the driver. Upon FW error, disconnect
notification is sent to user space for any associated stations. AP is
then internally restarted with the stored configuration.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When enlarging rx_ring_order module param, wil6210 fails to load
because there are not enough Rx buffers.
Fix this by enlarging number of Rx buffers at startup, if needed based
on rx_ring_order.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In Talyn-MB, the 11ad throughput is higher and performance drops
may occur in the current RX configuration due to unavailability
of Rx buffers.
Increase the RX descriptor ring, RX status ring and number of RX
buffers to stabilize the performance in high throughput.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With current reset flow, Talyn sometimes get stuck causing PCIe
enumeration to fail. Fix this by removing some reset flow operations
that are not relevant for Talyn.
Setting bit 15 in RGF_HP_CTRL is WBE specific and is not in use for
all wil6210 devices.
For Sparrow, BIT_HPAL_PERST_FROM_PAD and BIT_CAR_PERST_RST were set
as a WA an HW issue.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Setting the same fake hash to all skbs prevents
distributing different flows to different CPU cores.
Signed-off-by: Hamad Kadmany <hkadmany@codeaurora.org>
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1056534 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 201383 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
new_flags is not used after setting its value. It is safe to remove
the unused variable.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1056532 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1056532 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1056532 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath10k/wmi-tlv.c: In function 'ath10k_wmi_tlv_op_gen_config_pno_start':
drivers/net/wireless/ath/ath10k/wmi-tlv.c:3455:6: warning:
variable 'tlv_len' set but not used [-Wunused-but-set-variable]
It never used since inroduction in commit
ce834e280f ("ath10k: support NET_DETECT WoWLAN feature")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to some spelling mistakes in ath10k_err and ath10k_dbg
messages:
"capablity" -> "capability"
"registed" -> "registered"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
I had a couple concerns with this code. First, we definitely need to
set the error code if the kzalloc() fails. Secondly, I was worried that
if we didn't set "arsta->tx_stats" to NULL after freeing it, then it
looks to me like it might lead to a use after free. I can't test that,
but it's harmless to set it to NULL so I did.
Fixes: a904417fc8 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The host driver currently expects the channel info event to be
received in pairs for all the channels, i.e. the first
chan_info event for a particular channel will not have the
COMPLETE flag set and the second chan_info event for the
same channel will have the COMPLETE flag set.
The HL2.0 firmware sends only one channel info event per channel
which is scanned without the COMPLETE flag set. After sending the
chan_info_event for all the channels, the HL2.0 firmware sends a
chan_info_event with COMPLETE flag set to indicate the completion
of the channel info event.
The firmware does not indicate this behavior with any service bitmap
and hence a new firmware feature flag is used to handle the modified
parsing of the channel info events, in the host driver, for the
firmware which sends single channel info event per scanned channel.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Co-developed-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The return value from devm_memremap() is not checked correctly.
The test is done against a wrong variable. This patch fix it.
Fixes: ba94c753cc ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ar->target_version is same for QCA99x0, QCA4019, QCA9888
and QCA9984, this ended up in assigning the wrong hw_mem_layouts.
This patch adds additional hw_rev check to assign correct
hw_mem_layouts.
Tested on:
QCA4019 firmware 10.4-3.2.1.1-00017
QCA9984 firmware 10.4-3.5.3-00057
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds firmware crash memory dump support for QCA4019.
Tested on:
QCA4019 firmware 10.4-3.2.1.1-00017
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds the tx statistics pkts/bytes dump
in rate table format.
Dump format table is similar to http://mcsindex.com/
Tested on QCA9984/QCA4019/QCA988x
Firmware: 10.4-3.5.3-00057
10.2.4-1.0-00037
command:
cat /sys/kernel/debug/ieee80211/phy0/netdev\:wlan0/
stations/<MACADDR>/tx_stats
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Christian Lamparter