The return value from the call to cht_wc_leds_find_freq() is int.
However, the return value is being assigned to an unsigned
int variable 'ctrl', so making it an int.
Eliminate the following warning:
drivers/leds/leds-cht-wcove.c:236 cht_wc_leds_set_effect() warn: unsigned 'ctrl' is never less than zero.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=5341
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230531020238.102684-1-yang.lee@linux.alibaba.com
The desired default behavior of LED1 / the charge LED is breathing
while charging and on/solid when full. Since triggers cannot select
breathing, blink_set() gets called when charging. Use breathing
when the default "charging-blink-full-solid" trigger is used to
achieve the desired default behavior.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230430195952.862527-6-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
The hw-blinking of the LED controller in the Whiskey Cove PMIC can also
be used for a hw-breathing effect.
As discussed during review of v2 of the submission of the new
leds-cht-wcove driver, the LED subsystem already supports breathing mode
on several other LED controllers using the hw_pattern interface.
Implement a pattern_set callback to implement breathing mode modelled
after the breathing mode supported by the SC27xx breathing light and
Crane EL15203000 LED drivers. The Whiskey Cove PMIC's breathing mode
is closer to the EL15203000 one then to the SC27xx one since it does
not support staying high / low for a specific time, it only supports
rise and fall times.
As such the supported hw_pattern and the documentation for this is almost
a 1:1 copy of the pattern/docs for the EL15203000 breathing mode.
Suggested-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Link: https://lore.kernel.org/all/6beed61c-1fc6-6525-e873-a8978f5fbffb@gmail.com/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230430195952.862527-4-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
When LED1 is showing the tablet is charging and then the device gets
suspended followed by unplugging the charger, then it will incorrectly
still show it is charging.
To avoid this turn both LEDs off on suspend, just like the PMIC always
turns them off when the tablet is powered off (even if the tablet is
charging). If hw-control is supported for LED1, then restore the
initial hw-control settings to let the hw control LED1 while suspended.
To restore the state the LEDs had before suspending, save it before
turning the LEDs off and restore it on resume.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230430195952.862527-3-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
Add support for LEDs connected to the Intel Cherry Trail Whiskey Cove
PMIC. Charger and general-purpose LEDs are supported. Hardware blinking
is implemented, breathing is not.
This driver was tested with Lenovo Yoga Book notebook.
Changes by Hans de Goede (in response to review of v2):
- Since the PMIC is connected to the battery any changes we make to
the LED settings are permanent, even surviving reboot / poweroff.
Save LED1 register settings on probe() and if auto-/hw-control was
enabled on probe() restore the settings on remove() and shutdown().
- Delay switching LED1 to software control mode to first brightness write.
- Use dynamically allocated drvdata instead of a global drvdata variable.
- Ensure the LED is on when activating blinking.
- Fix CHT_WC_LED_EFF_BREATHING val ((3 << 1) rather then BIT(3)).
Link: https://lore.kernel.org/r/20190212205901.13037-2-jekhor@gmail.com
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Co-developed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230430195952.862527-2-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
Jiapeng Chong