If rfkill is on il_grab_nic_access() fail and we can not write to the
various registers during stop procedure. Write to those registers
unconditionally instead.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The same data can be gathered using monitor mode.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unneeded structure and cleanup temperature calibration routines
a bit.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handers belongs logically into 4965-mac.c file.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
That change will save us some CPU cycles at run time. Having
port-based I/O seems to be not possible for PCIe devices.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wmb(), rmb() are not needed when writel(), readl() are used as
accessors for MMIO. We use them indirectly via iowrite32(),
ioread32().
What is needed mmiowb(), for synchronizing writes coming from
different CPUs on PCIe bridge (see in patch comments). This
fortunately is not needed on x86, where mmiowb() is just
defined as compiler barrier. As iwlegacy devices are most likely
not used on anything other than x86, this is not so important
fix.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before we write to the device register always check if
_il_grap_nic_access() was successful.
Change type return type _il_grap_nic_access() to bool, and
add likely()/unlikely() statements.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Print dump stack when the device is not responding. This should give
some more clue about the reason of failure. Also change the message we
print, since "MAC in deep sleep" is kinda confusing.
On the way add unlikely(), as fail to gain NIC access is hmm ...
unlikely.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Define RTL8190_MAX_RAW_FIRMWARE_CODE_SIZE which represents the
maximimum possible firmware file size. Use it in the definition
of the buffer which receives the firmware file data.
Set RTL8190_MAX_RAW_FIRMWARE_CODE_SIZE closer to the actual size of
the firmware file, e.g., 90000 (down from hard coded 164000). The current
size of rtlwifi/rtl8192sefw.bin is 88856.
Set max_fw_size to RTL8190_MAX_RAW_FIRMWARE_CODE_SIZE for the size limit
check. Fix the error case where max_fw_size is not cleared if the size
limit check fails.
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sdio driver part uses firmware name brcmfmac.bin. With addition
of usb this name is too generic. This patch renames the filename
to brcmfmac-sdio.bin.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch extends the use of the brcmfmac driver with support for
chipsets with a USB host interface. The first chipsets supported are
the bcm43235, bcm43236, and bcm43238 for which firmware has been
submitted.
This driver change has been successfully built for x86, x86_64,
ppc64, arm_le, and mips_be.
It has been tested successfully on x86 and x86_64.
Cc: M. Lambert <lambertm@westman.wave.ca>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Kan Yan <kanyan@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function is executed within irq context. The call spin_unlock_irq
does enable interrupts which is not desired in the irq context. This patch
replaces them using the spin_loc_irqsave and spin_unlock_irqrestore
functions.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Kan Yan <kanyan@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As the function is called from atomic context it should not do the
kzalloc call with GFP_KERNEL.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Kan Yan <kanyan@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bus state is updated in the sdio bus init function, but it is
better to do it when the brcmf_bus_start() function is completed
successfully. The brcmf_netdev_open() function will return -EAGAIN
until the state is updated instead of calling brcmf_bus_start() to
avoid reentering that function.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function brcmf_sdbrcm_bus_init() always returned success except for
firmware download failure. However, also when enabling SDIO function 2
is failing the function should return failure. This patch fixes that.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The module_init/exit functions are moved to dhd_linux.c to prepare
for supporting multiple host interface types.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fields bus_priv and drvr are defined as void pointer. It is
preferred to have specific types for compiler type checking. To
prepare for other bus types the bus_priv field is defined as a
union containing the sdio bus private structure reference.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
INIT_WORK only gets called after brcmf_proto_attach returns
success. This dependency should be annotated in brcmf_detach to
avoid any error.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch resolves the following smatch issues:
wl_cfg80211.c +1377 brcmf_cfg80211_connect(65) warn: min_t truncates
here '(sme->ssid_len)' (4294967295 vs 9223372036854775807)
dhd_sdio.c +1275 brcmf_sdbrcm_rxglom(156) warn: min_t truncates here
'(pfirst->len)' (2147483647 vs 4294967295)
dhd_sdio.c +1457 brcmf_sdbrcm_rxglom(338) warn: min_t truncates here
'(pfirst->len)' (2147483647 vs 4294967295)
bcmsdh_sdmmc.c +300 brcmf_sdioh_request_buffer(10) warn: variable
dereferenced before check 'pkt' (see line 295)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The A-MPDU code checked against a retry limit, but it was using
the wrong variable to do so. This patch fixes this to assure
proper retry mechanism.
This problem had a side-effect causing the mac80211 flush callback
to remain waiting forever as well. That side effect has been fixed
by commit by Stanislaw Gruszka:
commit f96b08a7e6
Date: Tue Jan 17 12:38:50 2012 +0100
brcmsmac: fix tx queue flush infinite loop
Reference:
https://bugzilla.kernel.org/show_bug.cgi?id=42576
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function wlc_phy_txpwrctrl_pwr_setup_nphy() does assign a local
variable target_pwr_qtrdbm in several code paths, but in the end all
code paths are coming to an assignment of that variable which does
override all previous. So those early and redundant assignments have
been removed.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The radio initialization for 2057 rev 5 was using the incorrect
register table for the initialization. This patch fixes that.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch correct some typos in a comment.
Signed-off-by: Tristan Pourcelot <tristan.pourcelot@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Devendra Naga <devendra.aaru@gmail.com> submitted a patch for rtl8192c_common
to change the tests in _rtl92c_store_pwrIndex_diffrate_offset(). This patch
improves on those changes and applies similar modifications to drivers rtl8192se
and rtl8192de.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: John Li <chen-yang.li@mediatek.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: John Li <chen-yang.li@mediatek.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
in _rtl92c_phy_calculate_bit_shift everytime the right shifted bitmask
is AND with 1 and compared against 1. i.e.
if ((bitmask >> i) & 0x1 == 1)
break;
which in the if condition is anyway becomes a 1 or 0.
Signed-off-by: Devendra.Naga <devendra.aaru@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rate control algorithms are supposed to stop processing when they
encounter a rate with the index -1. Checking for rate->count not being
zero is not enough.
Allowing a rate with negative index leads to memory corruption in
ath_debug_stat_rc().
One consequence of the bug is discussed at
https://bugzilla.redhat.com/show_bug.cgi?id=768639
Signed-off-by: Pavel Roskin <proski@gnu.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver maintains different flags for WEP, WPA, WPA2 security modes.
Appropriate flag is set using security information provided in
connect request. mwifiex_is_network_compatible() routine uses them
to check if driver's setting is compatible with AP. Association is
aborted if the routine fails.
For some corner cases, it is observed that association is failed
even for valid security information based on association history.
This patch fixes the problem by clearing previous security setting
during each association.
We should set WEP key provided in connect request as default tx key.
This missing change is also added here.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"ret" has already been checked at this point, and we don't need to check
it again. This was left around from a previous patch 49d750ca14
"wl12xx: 1281/1283 support - New radio structs and functions".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Delete the global wl->vif (and the checks on it),
so multiple vifs could be added.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Enter forced psm when changing fw, in order to make the
sta a bit more disconnection-persistent.
(DPM doesn't know about the incoming recovery, so it
won't enter psm by itself)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
wl12xx uses different fw for single-role and multi-role
scenarios (due to lack of space, some of the fw advanced
features are disabled in the multi-role fw).
Add checks on add_interfae and remove_interface in order
to determine whether a fw switch is needed (and initiate
recovery in this case).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Stanislaw Gruszka