* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
staging: zram: fix data corruption issue
Staging: Comedi: Fix a few NI module dependencies
Staging: comedi: Add MODULE_LICENSE and similar to NI modules
staging: brcm80211: bugfix for softmac crash on multi cpu configurations
staging: sst: Fix for dmic capture on v2 pmic
staging: hv: Enable sending GARP packet after live migration
In zram_read() and zram_write() we were not incrementing the
index number and thus were reading/writing values from/to
incorrect sectors on zram disk, resulting in data corruption.
Signed-off-by: Nitin Gupta <ngupta@vflare.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ni_tio and ni_tio modules do not depend on the 8255 module, but the
ni_atmio, ni_mio_cs and ni_pcimio modules do need the 8255 module. The
ni_pcimio module also needs the comedi_fc module.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As mentioned by W. Trevor King on the devel@linuxdriverproject.org list
on "Thu, 27 Jan 2011 18:52:15 -0500", "Message-ID:
<20110127235214.GA5107@thialfi.dhcp.drexel.edu>", the ni_pcimio module
is missing module metadata, including a license.
This patch adds module metadata to all the NI comedi driver modules. It
also removes a duplicate MODULE_LICENSE("GPL") line from the "mite"
module.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: W. Trevor King <wking@drexel.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'media_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] fix saa7111 non-detection
[media] rc/streamzap: fix reporting response times
[media] mceusb: really fix remaining keybounce issues
[media] rc: use time unit conversion macros correctly
[media] rc/ir-lirc-codec: add back debug spew
[media] ir-kbd-i2c: improve remote behavior with z8 behind usb
[media] lirc_zilog: z8 on usb doesn't like back-to-back i2c_master_send
[media] hdpvr: fix up i2c device registration
[media] rc/mce: add mappings for missing keys
[media] gspca - zc3xx: Discard the partial frames
[media] gspca - zc3xx: Fix bad images with the sensor hv7131r
[media] gspca - zc3xx: Bad delay when given by a table
Solved a locking issue that resulted in driver crashes with the 43224 and 43225
chips. The problem has been reported on several fora. Root cause was two fold:
hardware was being manipulated by two unsynchronized threads, and a scan
operation could interfere with an ongoing dynamic calibration process. Fix was
to invoke a lock on wl_ops_config() operation and to set internal flags when a
scan operation is started and stopped.
Please add this to the staging-linus branch.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Roland Vossen <rvossen@broadcom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
currently capture through dmic captures only silence
This patch configurs the dmic registers to capture properly
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The hv_netvsc gets RNDIS_STATUS_MEDIA_CONNECT event after the VM
is live migrated. Adding call to netif_notify_peers() for this event
to send GARP (Gratuitous ARP) to notify network peers. Otherwise,
the VM's network connection may stop after a live migration.
This patch should also be applied to stable kernel 2.6.32 and later.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Hank Janssen <hjanssen@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (26 commits)
staging: r8712u: Add new device IDs
staging: brcm80211: fix suspend/resume issue in brcmsmac
staging: brcm80211: remove assert to avoid panic since 2.6.37 kernel
Staging: iio: Aditional fixpoint formatted output bugfix
staging: usbip: vhci: use urb->dev->portnum to find port
staging: usbip: vhci: handle EAGAIN from SO_RCVTIMEO
staging: usbip: vhci: friendly log messages for connection errors
staging: usbip: vhci: refuse to enqueue for dead connections
staging: usbip: vhci: give back URBs from in-flight unlink requests
staging: usbip: vhci: update reference count for usb_device
staging: usbip: stub: update refcounts for devices and interfaces
staging: tidspbridge: replace mbox callback with notifier_call
staging: comedi: ni_labpc: Use shared IRQ for PCMCIA card
Staging: speakup: &&/|| confusion in silent_store()
iio: Fixpoint formatted output bugfix
staging: rt2860: Fix incorrect netif_stop_queue usage warning
staging: r8712u: Fix memory leak in firmware loading
staging: tidspbridge: configure full L1 MMU range
staging: rt2870sta: Add ID for Linksys WUSB100v2
Staging: xgfib: put parenthesis in the right place
...
Both the HD-PVR and HVR-1950, driven by the hdpvr and pvrusb2 drivers
respectively, have a zilog z8 chip exposed via i2c. These are both
usb-connected devices, and on both of them, back-to-back i2c_master_send
calls that work fine with a z8 on a pci card fail with a -EIO, as the
chip isn't yet ready from the prior command. To cope with that, add a
delay and retry loop where necessary.
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The -rt patches change the console_semaphore to console_mutex. As a
result, a quite large chunk of the patches changes all
acquire/release_console_sem() to acquire/release_console_mutex()
This commit makes things use more neutral function names which dont make
implications about the underlying lock.
The only real change is the return value of console_trylock which is
inverted from try_acquire_console_sem()
This patch also paves the way to switching console_sem from a semaphore to
a mutex.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: make console_trylock return 1 on success, per Geert]
Signed-off-by: Torben Hohn <torbenh@gmx.de>
Cc: Thomas Gleixner <tglx@tglx.de>
Cc: Greg KH <gregkh@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds several new device ids to the r8712u staging driver.
The new ids were retrieved from latest vendor driver (v2.6.6.0.20101111)
downloadable from www.realtek.com.tw
Signed-off-by: Axel Koellhofer <AxelKoellhofer@web.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org> [2.6.37]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI PM suspend callback took down the interface and resume brought
it back up. In the mac80211 context this is done in subsequent calls.
Rework implementation so that suspend only stores config, and sets
PCI power state. The resume return to full power state (D0), restores
the config, and brings hardware back up. Full bringup is done by
subsequent mac80211 calls.
Reviewed-by: Brett Rudley <brudley@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver assumed it would receive skb packets from MAC80211 which
are not cloned. To guard this assumption an assert was placed in
the transmit routine. As of kernel 2.6.37 it turns out MAC80211 does
pass skb packets that are cloned. The assert is also not needed as
it does not lead to a failure state in our driver when the packet is
cloned. Therefore the assert can safely be removed.
> commit f8a0a78148
> Author: Felix Fietkau <nbd@openwrt.org>
> Date: Sat Dec 18 19:30:50 2010 +0100
>
> mac80211: fix potentially redundant skb data copying
>
> When an skb is shared, it needs to be duplicated, along with its data
> If the skb does not have enough headroom, using skb_copy might cause t
> buffer to be copied twice (once by skb_copy and once by pskb_expand_he
> Fix this by using skb_clone initially and letting ieee80211_skb_resize
> out the rest.
>
> Signed-off-by: Felix Fietkau <nbd@openwrt.org>
> Signed-off-by: John W. Linville <linville@tuxdriver.com>
>
Acked-by: Brett Rudley <brudley@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
iio: Additional fixpoint formatted output bugfixes
Fix some ADC/DAC drivers' _scale interface to correct fixpoint formatted output
This patch adds the fixes to ad7887_core.c and ad5446.c
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The access to pending_port was racy when two devices
were being attached at the same time.
Signed-off-by: Max Vozeler <max@vozeler.com>
Tested-by: Mark Wehby <MWehby@luxotticaRetail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If there is a receive timeout without any active
requests, we can tell the connection was idle and
ignore the timeout.
If there are active requests for which we expect
to receive a reply we close the connection.
This makes it possible to set an upper bound on
the time a usbip device may be unresponsive.
This is a workaround for the lack of heart-beat
messages in the USBIP protocol.
Extending the protocol would break compatibility
with all previous stub versions, so this seems like
the lesser evil.
Signed-off-by: Max Vozeler <max@vozeler.com>
Tested-by: Mark Wehby <MWehby@luxotticaRetail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Also changes the event on connection close to be
VDEV_EVENT_DOWN - no functional change.
Signed-off-by: Max Vozeler <max@vozeler.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There can be requests to enqueue URBs while we are shutting
down a connection.
Signed-off-by: Max Vozeler <max@vozeler.com>
Tested-by: Mark Wehby <MWehby@luxotticaRetail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we never received a RET_UNLINK because the TCP
connection broke the pending URBs still need to be
unlinked and given back.
Previously processes would be stuck trying to kill
the URB even after the device was detached.
Signed-off-by: Max Vozeler <max@vozeler.com>
Tested-by: Mark Wehby <MWehby@luxotticaRetail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Lately, mailbox callbacks have been replaced by notifier block
call chains, this needs to be changed in the users of mailbox,
otherwise compilation will break due to missing parameters.
For this new change to work, io_mbox_msg needs to be compatible
with the notifier_call definition.
Reported-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ni_labpc driver module only requests a shared IRQ for PCI devices,
requesting a non-shared IRQ for non-PCI devices.
As this module is also used by the ni_labpc_cs module for certain
National Instruments PCMCIA cards, it also needs to request a shared IRQ
for PCMCIA devices, otherwise you get a IRQ mismatch with the CardBus
controller.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The TX queues are allocated inside register_netdev.
It doesn't make any sense to stop the queue before
allocation.
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
IVA MMU can manage up to 4GB of address space through its page tables,
given that it's L1 is divided into 1MB sections it requires at least
16KB for its table which represents 4096 entries of 32 bits each.
Previously, only 1GB was being handled by setting the page table size
to 4KB, any virtual address beyond of the L1 size used, would fall
into memory that does not belong to L1 translation tables, leading to
unpredictable results.
So, set the L1 table size to cover the entire MMU range (4GB) whether
is meant to be used or not.
Reported-by: Felipe Contreras <felipe.contreras@nokia.com>
Signed-off-by: Fernando Guzman Lugo <fernando.lugo@ti.com>
Signed-off-by: Felipe Contreras <felipe.contreras@nokia.com>
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This device was tested with rt2870sta by setting new_id.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Brian Ormond <brian.ormond@oit.edu>
Cc: Stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the original code the parenthesis are in the wrong position, so the
conditions are always true.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The original code called input_free_device(rmi4_data->input_dev) after
input_unregister_device(rmi4_data->input_dev) and that's a double free.
This is described in the comments to input_unregister_device().
The normal way to handle this is to make input_register_device() the
last function in the probe which can fail. That way you can avoid the
call to input_unregister_device() entirely.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Off by one
Signed-off-by: Phillip Simbwa <simbwa at gmail dot com>
Signed-off-by: Vipin Mehta <vmehta@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removed the call to netif_stop_queue() in netvsc_probe() as
the queue is not initialized at that point and further call
to it after queue initialization is really not necessary.
This change was prompted after an upstream change went into
2.6.37 (netif_tx_stop_queue) that now checks if netif_stop_queue
is called before register with netdev is done.
This will eliminate the warning message to the log when hv_netvsc
driver starts up.
Signed-off-by: Abhishek Kane <v-abkane@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Hank Janssen <hjanssen@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The channel callbacks are called directly from vmbus_event_dpc
which runs in tasklet context. These callbacks need to use
GFP_ATOMIC.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16701
Cc: Hank Janssen <hjanssen@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The block device does not create the proper symlink in sysfs because we
forgot to set up the gendisk structure properly. This patch fixes the
issue.
Signed-off-by: K. Y. Srinivasan <ksrinivasan@novell.com>
Cc: Hank Janssen <hjanssen@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the lirc drivers were converted over to using memdup_user, I
mistakenly also removed corresponding calls to kfree. Add those back. I
also screwed up on the allocation error check in lirc_serial, using if
(PTR_ERR()) instead of if (IS_ERR()), which broke transmit.
Reported-by: Jiri Fojtasek <jiri.fojtasek@hlohovec.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ir_command() function is a do-nothing stub; remove it.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver is now structured so that it must handle an IR Tx unit
for a Z8 IR chip, or it refuses to handle that Z8 IR chip. This
allows us to assume that ir->tx != NULL in a few places in the driver,
and also allows us to always report Tx is available to userspace.
Get rid of unneeded tests for ir->tx == NULL and always report that
Tx is available.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The IR Rx polling thread was originally a kernel_thread long ago,
and had only been minimally converted to a kthread. This patch
finishes that conversion by
- cleaning up all the unneeded completions
- destroying the kthread properly by calling kthread_stop()
- changing lirc_thread() to test kthread_should_stop() just before
every point where it may sleep
- reorganizing the lirc_thread() function so it uses fewer lines
- modifying the name of the kthread from "lirc_zilog" to
"zilog-rx-i2c-N", so ps will show which kthread polls
which Zilog Z8 IR unit.
Also some minor tweaks were made to logging emitted by the
ir_probe() function.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is an extensive rework of the ir_probe() and ir_remove() functions.
It removes all the double binding and allocation problems on module load.
It removes almost all the memory leaks on module exit and on device
instantiation failure. Proper destruction of the Rx polling kthread still
needs investigation and more work, but it is no worse than it already was.
This rework also had side effects that include:
- encapsulation of the ir_devices[] array
- serialization of access to the ir_devices[] array
- semantic change of the module parameter "disable_rx" to "tx_only"
If tx_only is true, the module does not claim the i2c_client for the IR Rx
function, and only claims and handles the i2c_client for the IR Tx function.
This is a first step in providing the option of letting ir-kbd-i2c.c handle
IR Rx function, while lirc_zilog handles the IR Tx function.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't make private copies of the i2c clients provided by the I2C
subsystem, don't change the client address field, and don't probe
the client addresses - the bridge driver already did that. This
moves us to the proper I2C and binding model.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change is a mostly mechanical break of the main struct IR
data structure into common, Rx, and Tx structures. There were some
small logical changes required as well, such as eliminating "is_hdpvr",
to accomplish this.
This change is an intiial step in reworking lirc_zilog to decouple the
Rx and Tx handling as much as possible to fit with the new I2C
binding model. This change actually makes lirc_zilog a little more
broken than it already was - memory deallocation in particular got worse.
However, this change makes the remaining problems easier to see and address.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The only reason to use the lirc_zilog module is for IR Tx, so remove
the possibility of disabling IR Tx. If the user needs only IR Rx,
then the ir-kbd-i2c module works just fine, and doesn't require a
"firmware" image.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean Delvare <khali@linux-fr.org> suggested this better
format for debug output in ir_probe().
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Linus Torvalds