The mms114 binding [1] specifies that the 'x' and 'y' should be
called respectively 'touchscreen-size-x' and 'touchscreen-size-y'
in coherence with the touchscreen [2] binding.
Update the mms114 node for trats2 and trats dts according to the
binding.
[1] Documentation/devicetree/bindings/input/touchscreen/mms114.txt
[2] Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
There are 3 scaler devices in Exynos5420 SoCs, all are a part of MSCL
power domain. MSCL power domain and SYSMMU controllers (two per each
scaler device) have been already added to exynos5420.dtsi earlier,
so bind them to newly added devices.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The DTC was warning a lot about unit names etc, I think I fixed
them all. Stopping to include skeleton.dtsi fixes the last one.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The NAS4220B has the second ATA interface up and running.
Activate it in the device tree.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These machines need to be booted from very specific harddisk
partitions (as the D-Link DNS-313 boots specifically from
partition 4). Add the proper bootargs so that everything works
smoothly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The flash on the DNS-313 needs to be probed as JEDEC, it does
not conform to the common CFI standard.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Using the blue LED for disk read and the orange LED for
disk write gives a better user experience.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We just used one LED for "disk activity" but using the green
LED for disk read and the red LED for disk write gives a way
better user experience.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This new syntax is slightly better designed & uses "compatible" string.
For details see Documentation/devicetree/bindings/mtd/partition.txt .
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add MT7623N reference board with eMMC. On the board, there is additional
external PHY ICPlus IP1001 transceiver available by port 5 on the MDIO
bus connectted with GMAC2.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Suggested-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add MT7623A reference board with eMMC and NAND, respectively.
The both boards compared against MT7623N BPI-R2, we could see there are
UART[0-1] and USB2 being removed, I2C2 and SPI1 being added, I2C1, UART2
owning distinct pin usage and an extra WM8960 codec chip plugged into the
I2C1 offering the functionality of audio player and recorder through
SoC audio front-end engine (AFE).
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Suggested-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a common file for MT7623A SoC level DTS, indicating MT7623A only
has a specific definition for power domain. That causes we need to change
related consumers devices such as audio, ethernet, crypto, NAND, and USB
controller to grasp its own power domain it should belong to.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Move all possible setups for pio into SoC level DTSI file mt7623.dtsi in
order to introduce more boards such as official MT7623A reference boards
without copy-n-pasting almost the same content of nodes in pio into every
new file.
So, it should be better to reuse those nodes by consolidating them into
the common file mt7623.dtsi from the current existent DTS and allow new
DTS files to refer to them.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Since those LEDs are parts of PMIC MT6323, it is reasonable to merge
those LEDs node definition back into mt6323.dtsi. This way can improve
the reusability of those nodes among different boards with the same PMIC.
And LED is very much board specific and thus the mt6323.dtsi only includes
the parent node here and leave these child nodes in the board specific
dts file.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
add BTIF, HSDMA and SPI-NOR device nodes and enable it on relevant boards
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Fix below a lot of Warnings (unit_address_vs_reg) that dtc complains so
much for
Node /oscillator@1 has a unit name, but no reg property
Node /oscillator@0 has a unit name, but no reg property
Node /pinctrl@10005000/cir@0 has a unit name, but no reg property
Node /pinctrl@10005000/i2c@0 has a unit name, but no reg property
Node /pinctrl@10005000/i2c@1 has a unit name, but no reg property
Node /pinctrl@10005000/i2s@0 has a unit name, but no reg property
Node /pinctrl@10005000/i2s@1 has a unit name, but no reg property
Node /pinctrl@10005000/keys@0 has a unit name, but no reg property
Node /pinctrl@10005000/leds@0 has a unit name, but no reg property
Node /pinctrl@10005000/pwm@0 has a unit name, but no reg property
Node /pinctrl@10005000/spi@0 has a unit name, but no reg property
Node /pinctrl@10005000/uart@0 has a unit name, but no reg property
Node /pinctrl@10005000/uart@1 has a unit name, but no reg property
Node /pinctrl@10005000/uart@2 has a unit name, but no reg property
Node /ethernet@1b100000/mdio-bus/switch@0/ports has a reg or ranges
property, but no unit name
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
There is 2GB DDR3 available on bananapi-r2 board as [1] specified.
[1] http://www.banana-pi.org/r2.html
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Below two wrong nodes in existing DTS files would cause a fail boot since
in fact the address 0 is not the correct place the memory device locates
at.
memory {
device_type = "memory";
reg = <0x0 0x0 0x0 0x0>;
};
memory@80000000 {
reg = <0x0 0x80000000 0x0 0x40000000>;
};
In order to avoid having a memory node starting at address 0, we can't
include file skeleton64.dtsi and instead need to explicitly manually
define a few of properties the DTS relies on such as #address-cells
and #size-cells in root node and device_type in the node memory@80000000.
Cc: stable@vger.kernel.org
Fixes: 31ac0d69a1 ("ARM: dts: mediatek: add MT7623 basic support")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The latest DTC throws warnings for character '_' in the node names.
Warning (node_name_chars_strict): /pmu_a15: Character '_' not recommended in node name
Warning (node_name_chars_strict): /pmu_a7: Character '_' not recommended in node name
The general recommendation is to use character '-' for all the node names.
This patch fixes the warnings following the recommendation.
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Commit 2cff6dba57 ("ARM: dts: vexpress: fix node name unit-address presence warnings")
removed the unit address as there was no associated reg property in
these sysreg nodes.
Also the latest DTC throws warnings for character '_' in the node names.
Warning (node_name_chars_strict): /sysreg@10000/sys_led: Character '_' not recommended in node name
Warning (node_name_chars_strict): /sysreg@10000/sys_mci: Character '_' not recommended in node name
Warning (node_name_chars_strict): /sysreg@10000/sys_flash: Character '_' not recommended in node name
The correct way to fix this as well as the original unit-address presence
warnings is to use the standard gpio controller binding and specify the
reg properties as per the hardware as it was before.
However note that Vexpress sysreg MFD driver will still continue to use
the hardcoded values for compatibility reasons.
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Suggested-by: Rob Herring <robh@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add SY8106A regulator to r_i2c bus and enable the r_i2c bus on
Orange Pi PC, then set the power supply of the ARM cores to this
regulator, in order to enable DVFS.
Signed-off-by: Ondrej Jirman <megous@megous.com>
[Icenowy: Enable DVFS in this patch, slight changes and change commit
message]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Tronsmart MXIII Plus is an Android TV box which uses the Amlogic
S812 (Meson8m2) SoC. It uses a Realtek RTL8211F RGMII Ethernet PHY as
well as a Ricoh RN5T618 system power controller. It also comes with an
Ampak AP6330 SDIO wifi/Bluetooth combo chip (support for wifi and
Bluetooth is currently not added because the Linux drivers currently
only support one MMC controller and that is used for the SD card).
Signed-off-by: Oleg Ivanov <balbes-150@yandex.ru>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds the pins for uart_A, which is used to connect to the Bluetooth
module on some devices.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds a meson8m2.dtsi which simply inherits meson8.dtsi as both SoCs
share most peripherals.
The known differences are:
- Meson8m2's hardware video decoder additionally supports H.265 decoding
- Meson8m2 has the same Gigabit MAC as Meson8b (instead of the 10/100M
MAC that Meson8 uses)
- Meson8m2 uses the same watchdog register layout/bits as Meson8b (using
the Meson8 watchdog compatible leads to an infinite hang when
rebooting the machine)
- Meson8m2 uses the same SAR ADC register layout/bits as Meson8b.
However, it uses the temperature sensor calibration formula (and
registers) Meson8b which differ from Meson8. This however is currently
not supported by the meson-saradc driver yet.
- the pin controller is mostly compatible with Meson8, Meson8m2 has
an additional function on eight pins and removes the "VGA" function.
So there's a total of 10 pins which are slightly changed, which is why
there's a separate compatible for the pin controller
- a separate compatible for the clock controller is used because at
least the Mali clock tree (not supported yet) is the same as on GXBB
while Meson8 and Meson8b have a reduced/older version of the Mali
clock tree.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Many node labels in the device tree (like serial0, serial1, etc) are being
redefined, so let's modernize the device tree by using phandles to
extend the existing nodes. This helps reduce the whitespace.
Signed-off-by: Adam Ford <aford173@gmail.com>
[nsekhar@ti.com: drop tps6507x related changes]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The Odroid-C1 comes with an IR receiver. It is connected to the GPIOAO_7
pin and thus using the SoC's internal IR decoder.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This makes it easier to find existing nodes. No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This matches licensing used by other BCM5301X files and is preferred as:
1) GPL 2.0+ makes is clearly compatible with Linux kernel
2) MIT is also permissive but preferred over ISC
This file were created and ever touched by a group of three people only:
Álvaro, Hauke and me.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It's an access point based on BCM47094 SoC with two BCM4366E wireless
chipsets.
Signed-off-by: Dan Haab <dan.haab@luxul.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Luxul XWR-3150 is a wireless router similar to the XWR-3100 except:
1) It has more RAM
2) Its NAND controller in running in BCH8 mode
3) LAN ports LEDs are hardware controlled
Signed-off-by: Dan Haab <dan.haab@luxul.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It is a bit unorthodox to just include a file in the middle of a another
DTS file, it breaks the pattern from other device trees and also makes
it really hard to reference things across the files with phandles.
Restructure the include for the Versatile Express motherboards to happen
at the top of the file, reference the target nodes directly, and indent
the motherboard .dtsi files to reflect their actual depth in the
hierarchy.
This is a purely syntactic change that result in the same DTB files from
the DTS/DTSI files.
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add the use of enable-method property for SMP support which allows
to handle the SMP support for this specific SoC.
This commit adds enable-method properties to all CPU nodes.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The R_CPUCFG is a collection of registers needed for SMP bringup
on clusters and cluster's reset.
For the moment, documentation about this register is found in
Allwinner's code only.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
As we found in sun9i-a80, CPUCFG is a collection of registers that are
mapped to the SoC's signals from each individual processor core and
associated peripherals.
These registers are used for SMP bringup and CPU hotplugging.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Same EEPROM as on Koelsch, et al.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit d50f4630c2 ("arm: dts: Remove p1010-flexcan compatible from imx
series dts") removed the fallback compatible "fsl,p1010-flexcan" from
the imx device trees. As the flexcan cores on i.MX25, i.MX35 and i.MX53
are identical, introduce the first as fallback for the two latter ones.
Fixes: d50f4630c2 ("arm: dts: Remove p1010-flexcan compatible from imx series dts")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.16
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Remove the usage of skeleton.dtsi to fix the DTC warnings:
arch/arm/boot/dts/s3c6410-mini6410.dtb: Warning (unit_address_vs_reg):
/memory: node has a reg or ranges property, but no unit name
arch/arm/boot/dts/s3c6410-smdk6410.dtb: Warning (unit_address_vs_reg):
/memory: node has a reg or ranges property, but no unit name
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Remove the usage of skeleton.dtsi to fix the DTC warning:
arch/arm/boot/dts/s3c2416-smdk2416.dtb: Warning (unit_address_vs_reg):
/memory: node has a reg or ranges property, but no unit name
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
As per ARM documentation
PPI(0) ID27 - global timer interrupt is rising-edge sensitive.
set IRQ triggering type to IRQ_TYPE_EDGE_RISING for ARM Global timers.
Fixes: c9ad7bc5fe ("ARM: dts: Enable Broadcom Cygnus SoC")
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This matches licensing used by other BCM5301X files and is preferred as:
1) GPL 2.0+ makes is clearly compatible with Linux kernel
2) MIT is also permissive but preferred over ISC
These files were created and ever touched by a group of four people
only: Felix, INAGAKI, Hauke and me.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Felix Fietkau <nbd@nbd.name>
Acked-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Currently the following error is seen from the CAAM driver:
caam 30900000.caam: device ID = 0x0a16030000000000 (Era -524)
Pass the 'fsl,sec-era' property to properly describe the
era information.
This error happens because the 'fsl,sec-era' is not passed via
device tree.
The era information is used in various places inside drivers/crypto/caam,
so pass the correct version via device tree.
Fixes: 0eeabcad7d ("ARM: dts: imx7s: add CAAM device node")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 66AK2G evm has support for dcan.
Add nodes and pinmuxes for dcan0 and dcan1.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Commit 4c9a27a6c6 ("ARM: tegra: Fix ULPI regression on Tegra20") changed
"ulpi-link" clock from CDEV2 to PLL_P_OUT4. Turned out that PLL_P_OUT4 is
the parent of CDEV2 clock and original clock setup of "ulpi-link" was
correct. The reverted patch was fixing USB for one board and broke the
other, now Tegra's clk driver correctly sets parent for the CDEV2 clock
and hence patch could be reverted safely, restoring USB for all of the
boards.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Marcel Ziswiler <marcel@ziswiler.com>
Tested-by: Marcel Ziswiler <marcel@ziswiler.com>
Tested-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The U8540 was an evolved version of the U8500, but it was never
mass produced or put into products, only reference designs exist.
The upstream support was never completed and it is unlikely that
this will happen so drop the support for now to simplify
maintenance of the U8500.
Cc: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
LPTimer pwm cells should be updated to 3, to allow initialization of
channel, period and polarity.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add display support on the stm32f469-disco board.
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
In the stm32f4 family, mipi dsi is only supported on stm32f469.
So add a new stm32f469 dtsi file & add mipi dsi support inside.
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Since commit 83a86fbb5b ("irqchip/gic: Loudly complain about
the use of IRQ_TYPE_NONE"), a warning is raised if IRQ_TYPE_NONE is used.
So we use IRQ_TYPE_LEVEL_HIGH for usart nodes instead of IRQ_TYPE_NONE.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Tested-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Fix DTC warnings for stm32mp157:
Warning (unit_address_vs_reg): /soc/pin-controller: node has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): /soc/pin-controller/uart4@0: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /soc/pin-controller-z: node has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds flash nor on qspi. Each flash is
connected in quad mode and has its own chip select.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds qspi support on stm32mp157c,
read in memory mapped, write in indirect mode.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add support for USBH (USB Host) to STM32MP157C SoC.
USBH is a USB Host controller supporting the standard registers used for
full- and low-speed (OHCI controller) and high-speed (EHCI controller).
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
This patch enables USBPHYC (USB PHY Controller) on stm32mp157c-ev1.
This enables the two usbphyc usb2 ports.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add support for USBPHYC (USB PHY Controller) to STM32MP157C SoC.
It manages two usb2 ports.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add support for the display controller ltdc.
Signed-off-by: yannick fertre <yannick.fertre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
These files were created and ever touched by a group of three people
only: Dan, Hauke and me. They were licensed under GNU/GPL or ISC.
Introducing and discussing SPDX-License-Identifier resulted in a
conclusion that ISC is a not recommended license (see also a
license-rules.rst). Moveover an old e-mail from Alan Cox was pointed
which explained that dual licensing is a safer solution than depending
on a common compatibility belief.
This commit switches most of BCM5301X DTS files to dual licensing using:
1) GPL 2.0+ to make sure they are compatible with Linux kernel
2) MIT to allow sharing with more permissive projects
Both licenses belong to the preferred ones (see LICENSES/preferred/).
An attempt to relicense remaining files will be made separately and will
require approve from more/other developers.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Dan Haab <dan.haab@luxul.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find arch/arm/boot/dts -type f \( -iname "*.dts" -o -iname "*.dtsi" \) -exec sed -i \
-e "s/@\([0-9a-fA-FxX\.;:#]\+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 \
{/g" -e "s/@0\+\(.\+\) {/@\1 {/g" {} +
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace: https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve also a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
[krzk: Rerun the command to include few more changes, adjust the commit msg]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
While the supported UHS mode can be obtained from CAPA2
register, SD Host Controller Standard Specification
doesn't define bits for MMC's HS200 and DDR mode capability.
Add properties to indicate MMC HS200 and DDR speed mode capability in
dt node.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use sdhci-omap programming model based on the generic sdhci
library for programming the eMMC/SD/SDIO controller.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for WLAN using wilink8 module. On dra76-evm, MMC4 is
used for connecting to wilink8 module.
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The wilink module is a combo wireless connectivity sdio
card based on Texas Instrument's wl18xx solution. It is a
4-wire, 1.8V, embedded sdio wlan device with an external
irq line and is power-controlled by a gpio-based fixed
regulator.
Add pinmux configuration and IODelay values for MMC4.
On dra7-evm, MMC4 is used for connecting to wilink module.
IODelay data credits to : Vishal Mahaveer <vishalm@ti.com>
and Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On TI's DRA74x EVM, EVM_3V6 is connected is connected to the VBAT line
of the wilink card. Model it here so that it can be used while adding
wilink8 WLAN support.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Wilink8 module is a combo wireless connectivity card based
on Texas Instrument's wl18xx solution.
Add support for the wlan capabilities of this module by muxing
the relevant mmc lines, and setting the required device-tree
data.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
[nsekhar@ti.com: drop WLAN_EN pinmux. It should be done by bootloader.
Also, some commit message adjustments]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IO lines of MMC2 in am57xx-beagle-x15/am57xx-idk is connected to
3.3v. Use "ddr_3_3v" instead of "ddr_1_8v" to indicate DDR mode
works in 3.3v on these boards.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Include dra76x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for am574x SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am574x-idk.dts.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit 0e43884cca ("ARM: dts: dra71-evm: Select pull
down for mmc1_clk line in default mode") modified mmc1_pins_default
pinctrl group in dra71-evm.dts to change the CLK line to
PIN_INPUT_PULLDOWN. However instead of changing the pinctrl group,
use the new pinctrl group "mmc1_pins_default_no_clk_pu" in
dra7-mmc-iodelay.dtsi added specifically to be used for CLK line
without external pull up.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit 18aa0f4bca ("ARM: dts: am57xx-idk: Select pull down
for mmc1_clk line in default mode") modified mmc1_pins_default
pinctrl group in am57xx-idk-common.dtsi in order to change the CLK
line to PIN_INPUT_PULLDOWN. However instead of modifying the pinctrl
group, use the new pinctrl group "mmc1_pins_default_no_clk_pu" in
dra7-mmc-iodelay.dtsi added specifically to be used for CLK line without
external pull up.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
During a short period when the bus voltage is switched from 3.3v to 1.8v,
(to enumerate UHS mode), the mmc module is disabled and the mmc IO lines
are kept in a state according to the programmed pad mux pull type.
According to 4.2.4.2 Timing to Switch Signal Voltage in "SD Specifications
Part 1 Physical Layer Specification Version 5.00 February 22, 2016", the
host should hold CLK low for at least 5ms.
In order to keep the card line low during voltage switch, the pad mux of
mmc1_clk line should be configured to pull down.
Add a new pinctrl group for clock line without pullup to be used in boards
where mmc1_clk line is not connected to an external pullup.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add "vqmmc-supply" property for mmc2 to indicate the supply connected
to the IO lines.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
mmc specific pinmux is selected from dra72x-mmc-iodelay.dtsi, so remove
it from dra72-evm-common.dtsi.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The missing "compatible" entries are needed by drivers/clk/ti/clkctrl.c,
and without them the structures initialized in drivers/clk/ti/clk-814x.c
are not passed to configuration code. The result is a "not found from
clkctrl data" error message, although boot proceeds anyway.
The reason why the compatible is not found is because the board specific
files override the SoC compatible without including it. This did not
cause any issues until with the clkctrl nodes got introduced.
Very lightly tested on a (lurching) AM3874 design that's in the middle
of a kernel upgrade from TI's abandoned 2.6.37 tree.
Also tested on j5eco-evm and hp-t410 to verify the clkctrl clocks are
found.
Fixes: bb30465b59 ("ARM: dts: dm814x: add clkctrl nodes")
Fixes: 80a06c0d83 ("ARM: dts: dm816x: add clkctrl nodes")
Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
[tony: updated to fix for 8168-evm, updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
These definitions are hex, and the old value (decimal 40) doesn't make
sense in the context. I do not have a T410 and cannot test if this makes
any practical difference.
Fixes: f24f1bdc02 ("ARM: dts: Enable emmc on hp t410")
signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Turns out the compatible "nvidia,tegra124-hsuart" does not (yet) exist
and everybody else also uses it only in conjunction with
"nvidia,tegra30-hsuart".
Reported-by: Martin Šafařík <msafarik@retia.cz>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Exynos5440 (quad-core A15 with GMAC, PCIe, SATA) was targeting
server platforms but it did not make it to the market really. There are
no development boards with it and probably there are no real products
neither. The development for Exynos5440 ended in 2013 and since then
the platform is in maintenance mode.
Remove all Device Tree sources for Exynos5440, as first step of removal
of the platform to simplify the code and drivers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andi Shyti <andi@etezian.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Add support for DAC (Digital to Analog Converter) to STM32MP157C.
STM32MP157C DAC has two output channels.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add LPtimer definitions, depending on features they provide:
- lptimer1 & 2 can act as PWM, trigger and encoder/counter
- lptimer3 can act as PWM and trigger
- lptimer4 & 5 can act as PWM
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
stm32mp157c has vrefbuf regulator that can provide analog reference
voltage from 1500mV to 2500mV.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Enable timer 6 on stm32mp157c-ed1 that can serve as trigger for
ADC for instance.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
stm32mp157c evaluation board has TIM2_CH4, TIM8_CH4 and TIM12_CH1
available on GPIO expansion connector.
Add PWM and associated triggers (for ADC/DAC) on these timers.
Keep them disabled so these pins can be used as GPIOs by default.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
On i.MX6SX SabreAuto board, there is external 24MHz clock
source for analog clock2, add this clock source to clock tree
and remove "clocks" container for all input clocks.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Trivial fix to spelling mistake in status text string
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Convert boilerplate license statement into proper SPDX identifier style.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The canonical compatible string is "atmel,maxtouch", let's use it. Also,
change the node name to be "touchscreen" rather than driver name.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add CAAM support on i.MX6UL.
Also, since CAAM is not available on i.MX6ULL the CAAM node
needs to be deleted in the imx6ull.dtsi.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The gpio_keys node does not have an address and thus does not need
address-cells or address size-properties.
This is flagged by dtc as follows:
# make dtbs W=1
arch/arm/boot/dts/emev2-kzm9d.dtb: Warning (avoid_unnecessary_addr_size): /gpio_keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
The vin port node does not have an address and thus does not need
address-cells or address size-properties.
This is flagged by dtc as follows:
# make dtbs W=1
arch/arm/boot/dts/r8a7794-silk.dtb: Warning (avoid_unnecessary_addr_size): /soc/video@e6ef0000/port: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
The vin port node does not have an address and thus does not need
address-cells or address size-properties.
This is flagged by dtc as follows:
# make dtbs W=1
arch/arm/boot/dts/r8a7794-alt.dtb: Warning (avoid_unnecessary_addr_size): /soc/video@e6ef0000/port: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
The vin port nodes does not have an address and thus does not need
address-cells or address size-properties.
This is flagged by dtc as follows:
# make dtbs W=1
arch/arm/boot/dts/r8a7791-koelsch.dtb: Warning (avoid_unnecessary_addr_size): /soc/video@e6ef0000/port: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
arch/arm/boot/dts/r8a7791-koelsch.dtb: Warning (avoid_unnecessary_addr_size): /soc/video@e6ef1000/port: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
The vin port nodes does not have an address and thus does not need
address-cells or address size-properties.
This is flagged by dtc as follows:
# make dtbs W=1
arch/arm/boot/dts/r8a7793-gose.dtb: Warning (avoid_unnecessary_addr_size): /soc/video@e6ef0000/port: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
arch/arm/boot/dts/r8a7793-gose.dtb: Warning (avoid_unnecessary_addr_size): /soc/video@e6ef1000/port: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
The vin port node does not have an address and thus does not need
address-cells or address size-properties.
This is flagged by dtc as follows:
# make dtbs W=1
arch/arm/boot/dts/r8a7791-porter.dtb: Warning (avoid_unnecessary_addr_size): /soc/video@e6ef0000/port: unnecessary #address-cells/#size-cells without
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
The vin port node does not have an address and thus does not need
address-cells or address size-properties.
This is flagged by dtc as follows:
# make dtbs W=1
arch/arm/boot/dts/r8a7790-lager.dtb: Warning (avoid_unnecessary_addr_size): /soc/video@e6ef1000/port: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
The pinmux controllers do not themselves need references to
'pinctrl-names' or 'pinctrl-0'
This patch removes some unnecessary typos.
Fixes: 89077c7145 ("ARM: dts: Add HSUSB2 EHCI Support to Logic PD DM37xx
SOM-LV")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- The n810 uses tlv320aic33 codec.
- GPIO118 is used as reset GPIO for the codec, which was missing.
- The MCLK of the codec is connected to the SYS_CLKOUT2 of omap2420. The
SYS_CLKOUT2 needs to be running at 12MHz.
- Add the pinctrl entries to configure the pins for GPIO118 and SYS_CLKOUT2
- Set DMIC clk mode for GPIO1
- Set DMIC data in for GPIO2
- Select 2V for the DMIC bias
- Add fixed regulators for the codec
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McBSP2 is used with the tlv320aic33 codec for audio.
Pin mux change is needed to get the needed signals in/out from the SoC.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the documentation the interrupt line is active low.
The patch will silence the warning from gic_irq_domain_translate():
"Make it clear that broken DTs are... broken"
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the documentation the interrupt line is active low.
The patch will silence the warning from gic_irq_domain_translate():
"Make it clear that broken DTs are... broken"
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the documentation the interrupt line is active low.
The patch will silence the warning from gic_irq_domain_translate():
"Make it clear that broken DTs are... broken"
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the documentation the interrupt line is active low.
The patch will silence the warning from gic_irq_domain_translate():
"Make it clear that broken DTs are... broken"
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
PocketBeagle is an ultra-tiny-yet-complete open-source USB-key-fob computer.
This board family can be indentified by the A335PBGL in the at24 eeprom:
A2: [aa 55 33 ee 41 33 33 35 50 42 47 4c 30 30 41 32 |.U3.A335PBGL00A2|]
http://beagleboard.org/pockethttps://github.com/beagleboard/pocketbeagle
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Drew Fustini <drew@beagleboard.org>
CC: Peter Robinson <pbrobinson@redhat.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
am335x-evm, am335x-evmsk and am335x-beaglebone are currently relying on
pinmux set by the bootloader to set the correct value for mmc1. Fix
this by adding pinmux data for the same in kernel.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board uses 26MHz oscillator for the twl4030 HFCLK.
This way we will not depend on the bootloader to configure the
CFG_BOOT:HFCLK_FREQ
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board uses 26MHz oscillator for the twl4030 HFCLK.
This way we will not depend on the bootloader to configure the
CFG_BOOT:HFCLK_FREQ
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board uses 26MHz oscillator for the twl4030 HFCLK.
This way we will not depend on the bootloader to configure the
CFG_BOOT:HFCLK_FREQ
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP35 and DM3730 SOM-LV contains a TSC2004 touch screen
controller connected to I2C3. This patch adds support for this
controller.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Audio has worked, but the mute pin has a weak pulldown which alows
some of the audio signal to pass very quietly. This patch fixes
that so the mute pin is actively driven high for mute or low for normal
operation.
Fixes: ab8dd3aed0 ("ARM: DTS: Add minimal Support for Logic
PD DM3730 SOM-LV")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The VAUX3 rail from the PMIC powers a clock driver which clocks
the WL127x. This corrects a bug which did not correctly associate
the vin-supply with the proper power rail.
This also fixes a typo in the pinmuxing to properly configure the
interrupt pin.
Fixes: ab8dd3aed0 ("ARM: DTS: Add minimal Support for Logic PD
DM3730 SOM-LV")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 5d3b50d3c0 ("ARM: dts: renesas: r8a7790: Add FDP1 instances")
introduced the FDP1 for the r8a7790, but broke the sort ordering of the
device tree nodes.
Move the last VSP up to it's peers to correct the ordering.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the iW-RainboW-G23S board dependent part of the
EtherAVB device node.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77470 part of the EtherAVB device node.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
There is a random number generator that updates a register in the SCU
every second. This is compatible with the timeriomem rng driver in the
kernel.
From the timeriomem_rng bindings:
quality: estimated number of bits of true entropy per 1024 bits read
from the rng. Defaults to zero which causes the kernel's default
quality to be used instead. Note that the default quality is usually
zero which disables using this rng to automatically fill the kernel's
entropy pool.
As to the recommended value for us to use:
Rick Altherr <raltherr@google.com> wrote:
> Quality is #bit of entropy per 1000 bits read. 100 is a
> conservative value that was suggested by those in the know.
Signed-off-by: Joel Stanley <joel@jms.id.au>
The "dp-controller" node is not a bus and it does not have children with
reg/ranges properties so remove address-cells and size-cells properties.
This fixes warnings for all Exynos5 boards:
arch/arm/boot/dts/exynos5250-arndale.dtb: Warning (avoid_unnecessary_addr_size):
/soc/dp-controller@145b0000: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
exynos4412-midas.dtsi is base for galaxy-s3.dtsi and n710x.dts. All of
them contain fixed regulators named "voltage-regulator-X". Their
indexes got mixed up while splitting common code in commit c769eaf7a8
("ARM: dts: exynos: Split Trats2 DTS in preparation for Midas boards").
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Consistently put fixed regulators directly below root node, instead of
artificial "regulators" node in Exynos4210 Origen and Exynos4412 N710x.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The children of gpio_keys node do not have reg/ranges properties so remove
address-cells and size-cells properties. This fixes warnings for
Exynos4210 Origen:
arch/arm/boot/dts/exynos4210-origen.dtb: Warning (avoid_unnecessary_addr_size):
/gpio_keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The children of regulators node do not have reg/ranges properties. Move the
children up one level, get rid of regulators node and remove
address-cells and size-cells properties. This fixes warnings for
Exynos4412 Midas family boards:
arch/arm/boot/dts/exynos4412-i9300.dtb: Warning (avoid_unnecessary_addr_size):
/regulators: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
arch/arm/boot/dts/exynos4412-i9305.dtb: Warning (avoid_unnecessary_addr_size):
/regulators: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
arch/arm/boot/dts/exynos4412-n710x.dtb: Warning (avoid_unnecessary_addr_size):
/regulators: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Enable the performance monitor unit on Meson8b.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the performance monitor unit on Meson8.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add PWM and trigger support to stm32mp157c.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Fix a build regression with split object directories reported by Russell
and fix range sizes for omap4 cm2 and prm modules.
-----BEGIN PGP SIGNATURE-----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=5SNP
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.17/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Pull "Two fixes for v4.17-rc cycle" from Tony Lindgren:
Fix a build regression with split object directories reported by Russell
and fix range sizes for omap4 cm2 and prm modules.
* tag 'omap-for-v4.17/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix build when using split object directories
ARM: dts: Fix cm2 and prm sizes for omap4
The DTS file for the NAS4220B had the pin config for the
ethernet interface set to the pins in the SL3512 SoC while
this system is using SL3516. Fix it by referencing the
right SL3516 pins instead of the SL3512 pins.
Cc: stable@vger.kernel.org
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Reported-by: Andreas Fiedler <andreas.fiedler@gmx.net>
Reported-by: Roman Yeryomin <roman@advem.lv>
Tested-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds a device tree file for the H2+ version of the Libre
Computer Board ALL-H3-CC. It is the same board first introduced in
commit 6ca358645d ("ARM: dts: sun8i: h3: Add dts file for Libre
Computer Board ALL-H3-CC H3 ver."), with the H3 SoC replaced with
the H2+ SoC, and has only two 2Gb DDR3 chips instead of four.
The device tree utilizes the common board design file for ALL-H3-CC,
providing just the model strings and SoC specifics.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The dtb entry for the Banana Pi M2 Zero in the device tree makefile
somehow ended up in between two Orange Pi boards.
Move it so the list is properly sorted.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Since the libretech-all-h3-cc can use either the H2+, H3 or H5, move the
content of the dts file to a common dtsi file to be included by the H3
variant and in a following patch the H5 variant.
By the way, update the SPDX licence tag position.
Suggested-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The voltage of the VCC-1V2 regulator on the ALL-H3-CC H3 ver. should be
1.2V, not the 3.3V currently defined in the device tree.
Fix the voltage in the device tree.
Fixes: 6ca358645d ("ARM: dts: sun8i: h3: Add dts file for Libre
Computer Board ALL-H3-CC H3 ver.")
Cc: <stable@vger.kernel.org> # 4.16.x
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Nintendo NES/SuperNES features an R16 already well supported in
mainline.
The console over UART0 may be wired on two ports of the R16, both
available on the NES Classic PCB.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The r8a7790 has three FDP1 instances.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe SCIF ports in the R8A77470 device tree.
Also it fixes the CPG clock index ZS from 6 to 5.
Fixes: 6929dfc591 ("ARM: dts: r8a77470: Initial SoC device tree")
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the watchdog, so the board can be restarted by a watchdog
timeout.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the watchdog, so the board can be restarted by a watchdog
timeout.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the watchdog, so the board can be restarted by a watchdog
timeout.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the watchdog, so the board can be restarted by a watchdog
timeout.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the watchdog, so the board can be restarted by a watchdog
timeout.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the watchdog, so the board can be restarted by a watchdog
timeout.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the watchdog, so the board can be restarted by a watchdog
timeout.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the watchdog, so the board can be restarted by a watchdog
timeout.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Watchdog Timer (WDT) controller on the Renesas
R-Car M2-N (r8a7793) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Watchdog Timer (WDT) controller on the Renesas
R-Car V2H (r8a7792) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables the watchdog from within the iwg20m SoM dtsi.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables the watchdog from within the iwg20m SoM dtsi.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This commit adds watchdog support to the r8a7794 dtsi.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This commit adds watchdog support to the r8a7791 dtsi.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This commit adds watchdog support to the r8a7790 dtsi.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds watchdog support to the r8a7745 SoC dtsi.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds watchdog support to the r8a7743 SoC dtsi.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adjusts the definition of the SMP routine size according
to the latest changes made by commit:
"ARM: shmobile: Add watchdog support"
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adjusts the definition of the SMP routine size according
to the latest changes made by commit:
"ARM: shmobile: Add watchdog support"
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adjusts the definition of the SMP routine size according
to the latest changes made by commit:
"ARM: shmobile: Add watchdog support"
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adjusts the definition of the SMP routine size according
to the latest changes made by commit:
"ARM: shmobile: Add watchdog support"
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adjusts the definition of the SMP routine size according
to the latest changes made by commit:
"ARM: shmobile: Add watchdog support"
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adjusts the definition of the SMP routine size according
to the latest changes made by commit:
"ARM: shmobile: Add watchdog support"
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adjusts the definition of the SMP routine size according
to the latest changes made by commit:
"ARM: shmobile: Add watchdog support"
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a7794 has one FDP1 instance.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a7793 has two FDP1 instances.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a7791 has two FDP1 instances.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
After moving all nodes under "soc" node in commit 5d99cc59a3 ("ARM:
dts: exynos: Move Exynos5250 and Exynos5420 nodes under soc"), the i2c20
alias in Peach Pit and Peach Pi stopped pointing to proper node:
arch/arm/boot/dts/exynos5420-peach-pit.dtb: Warning (alias_paths):
/aliases:i2c20: aliases property is not a valid node (/spi@12d40000/cros-ec@0/i2c-tunnel)
arch/arm/boot/dts/exynos5800-peach-pi.dtb: Warning (alias_paths):
/aliases:i2c20: aliases property is not a valid node (/spi@12d40000/cros-ec@0/i2c-tunnel)
Fixes: 5d99cc59a3 ("ARM: dts: exynos: Move Exynos5250 and Exynos5420 nodes under soc")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add syscon-phy-mode property specifying a phandle of system controller
to each ethernet node.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The GIO clock/reset, Another MAC clock, and the PHY clock are required
for the ethernet of Pro4 SoC.
And add clock-names and reset-names to the ethernet node of PXs2 since
we need to distinguish clocks and resets now.
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Using 'at' or 'at24' as the <manufacturer> part of the compatible
string is now deprecated. Use a correct value: 'atmel,<model>'.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Remove unused #address-cells and #size-cells from pinmux
node. This fixes W=1 warnings of the type:
arch/arm/boot/dts/da850-lcdk.dtb: Warning (avoid_unnecessary_addr_size): /soc@1c00000/pinmux@14120: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Tested on DA850 LCDK by checking output of:
/sys/kernel/debug/pinctrl/1c14120.pinmux-pinctrl-single/pins
before and after the change.
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add unit name for memory node to squash the W=1 warning:
arch/arm/boot/dts/da850-lcdk.dtb: Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name
While at it, drop the device_type property from memory
node since its provided by da850.dtsi already.
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
skeleton.dtsi is deprecated. Drop its usage in da850.dtsi
and move the nodes and properties included by it directly
to keep the dtb same.
The memory node has been changed to get rid of warnings
(see below). It contains the memory base address as that is
fixed for DA850 SoCs. But the size needs to be added by
bootloader or a board specific dts.
This gets rid of the following W=1 warnings:
arch/arm/boot/dts/da850-enbw-cmc.dtb: Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name
arch/arm/boot/dts/da850-evm.dtb: Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name
arch/arm/boot/dts/da850-lego-ev3.dtb: Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The ALL-H3-CC has a fixed VDD-CPUX voltage at 1.2V, which is supplied
by a regulator.
Set the CPU's cpu-supply property to the VDD-CPUX regulator.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[wens@csie.org: Fix device node ordering]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The VDD-CPUX voltage of ALL-H3-CC H3 ver should be 1.2V, not the 3.3V
currently defined in the device tree.
Fix the voltage in the device tree.
Fixes: 6ca358645d ("ARM: dts: sun8i: h3: Add dts file for Libre Computer Board ALL-H3-CC H3 ver.")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Cc: <stable@vger.kernel.org> # 4.16.x
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Raspberry Pi 3 B+ has the following major differences compared
to the model 3 B:
* Microchip LAN7515 (Gigabit Ethernet with integrated USB 2.0 HUB)
* Cypress CYW43455 (802.11n/ac and BT 4.2)
We need to add the USB LAN chip so the bootloader can add the MAC address.
This is necessary because there ain't an EEPROM or a valid OTP.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
After commit a98d90e7d5 ("gpio: raspberrypi-exp: Driver for RPi3 GPIO
expander via mailbox service") we are able to control the rest of the
GPIOs of the RPi 3. So add all the missing parts (ACT LED,
Wifi & BT control, HDMI detect) to the DT.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
All RPi 1 and 2 boards used the PWM (audio out) on pin 40 and 45.
So it was easy to define them in bcm2835-rpi.dtsi. Starting with RPi 3
this wont work anymore, because it uses pin 40 and 41. Furthermore the
Zero variants doesn't have audio out.
This patch fixes this pin conflict by moving the PWM node to the board-level.
Change summary:
RPi 3 B: PWM1 45 -> 41
Zero, Zero W: PWM disabled
all other: no functional change
Reported-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
The internal LVDS encoder now has DT bindings separate from the DU. Port
the device tree over to the new model.
Fixes: c6a27fa41f ("drm: rcar-du: Convert LVDS encoder code to bridge driver")
Fixes: bff8f8c2fe ("ARM: dts: r8a7793: add soc node")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The internal LVDS encoder now has DT bindings separate from the DU. Port
the device tree over to the new model.
Fixes: c6a27fa41f ("drm: rcar-du: Convert LVDS encoder code to bridge driver")
Fixes: bb21803ea4 ("ARM: dts: r8a7791: add soc node")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The internal LVDS encoder now has DT bindings separate from the DU. Port
the device tree over to the new model.
Fixes: c6a27fa41f ("drm: rcar-du: Convert LVDS encoder code to bridge driver")
Fixes: 4bdb7aa7dc ("ARM: dts: r8a7790: add soc node")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This touchscreen is present instead of the RMI4 touch on some SKUs of
the RDU2. Keep it disabled by default, the bootloader will enable it
instead of the RMI4 touch when running on one of those units.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This downclocks the shader domain from 720MHz to 594MHz, which gets rid
of brown-outs due to excessive current draw on the PMIC switchers. The
board has an unchanged power tree from the Quad design, which isn't able
to cope with higher current needs of the QuadPlus GPU at full speed.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This bumps the SoC/PU domain operating points by 25mV, giving a total
of 75mV margin to the minimum required voltages. This gets rid of
brown-outs seen due to voltage drop-out on the board.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 'bus-format-override' property is not documented nor used
anywhere else, so just remove it.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The previous implementation has had a detrimental effect on devices using
high bitrates (bluetooth), as the fifo being non-empty for a single check
would result in a 10 µs delay.
Limit the change to devices with the new "marvell,armada-38x-uart"
compatible string. Also update the code to allow the first 1000 retries
to not perform a delay.
The maximum duration of retries has been increased to cover a worst-case
seen on the Armada 385 SoC. "dmesg ; resize", will fill the buffer with
text to output before doing a resize. At 9600 baud this took up to 13 ms
to flush all characters and avoid some getting lost.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some displays on sun4i devices wouldn't properly stay on unless
'clk_ignore_unused' is used.
Change the duplicate clocks to the probably intended ones.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pascal Roeleven <dev@pascalroeleven.nl>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The PMU node is the actual block responsible for power management,
including typical Exynos on/off/restart procedures. Therefore the
syscon poweroff and restart nodes logically belong to it.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
The Asus Tinker Board uses serial 2 with 115,200 baud by default for
communication in U-Boot. The same value is also chosen for other RK3288
boards.
So let us set the same value in the Tinker Board device tree.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Orange Pi One board has a SY8113B regulator, which is controlled via
GPIO and capable of outputing 1.1V when the PL6 GPIO is set to output 0
or 1.3V when the PL6 GPIO is set to input or output 1, and the output is
the power supply of the ARM cores in H3 SoC.
Add the device tree node of this regulator and set the cpu's cpu-supply
property to it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[wens@csie.org: rename regulator node name and label]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Orange Pi Zero board has a SY8113B regulator, which is controlled via
GPIO and capable of outputing 1.1V when the PL6 GPIO is set to output 0
or 1.3V when the PL6 GPIO is set to input or output 1, and the output is
the power supply of the ARM cores in H2+ SoC.
Add the device tree node of this regulator and set the cpu's cpu-supply
property to it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
[wens@csie.org: rename regulator node name and label]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The CPU on Allwinner H3 can do dynamic frequency scaling.
Add a DVFS table based on the one shipped with Allwinner's H3 SDK. The
voltage-frequency relationship seems to be conservative, and Armbian has
another DVFS table which uses lower voltage at a certain frequency.
However, the official one is chosen for safety.
Frequencies higher than 1008MHz are temporarily dropped in the table, as
they may lead to over voltage on boards without proper regulator
settings or over temperature on boards with proper regulator settings.
They will be added back once regulator settings are ready and thermal
sensor driver is merged.
In order to satisfy all different regulators (SY8106A which is 50mV per
level, SY8113B which have two states: 1.1V and 1.3V, and some board with
non-tweakable regulators), all the OPPs are defined with a range which has
the target value as the minimum allowed value, and 1.3V (the highest
VDD-CPUX voltage suggested by the datasheet) as the maximum allowed value.
It's proven to work well with a board with SY8113B.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Allwinner H3/H5 SoCs have an I2C controller at PL GPIO bank.
Add support for it in the device tree.
Signed-off-by: Ondrej Jirman <megous@megous.com>
[Icenowy: Change to use r_ccu and change pinmux node name]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
H3/H5 SoCs contain an I2C controller optionally available
on the PL0 and PL1 pins. This patch adds pinmux configuration
for this controller.
Signed-off-by: Ondrej Jirman <megous@megous.com>
[Icenowy: change commit message, node name and function name]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Allwinner a83t has a 1 KB sid block with efuse for security rootkey and thermal
calibration data, add node to describe it.
a83t-sid is not currently supported by nvmem/sunxi-sid, but it is
supported in an external driver for FreeBSD.
Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The iMX6ULL UART5_RX_DATA_SELECT_INPUT DAISY Register has some different
bit definitions to that same register in the iMX6UL.
The bits for the iMX6UL:
000 CSI_DATA00_ALT8 — Selecting Pad: CSI_DATA00 for Mode: ALT8
001 CSI_DATA01_ALT8 — Selecting Pad: CSI_DATA01 for Mode: ALT8
010 GPIO1_IO04_ALT8 — Selecting Pad: GPIO1_IO04 for Mode: ALT8
011 GPIO1_IO05_ALT8 — Selecting Pad: GPIO1_IO05 for Mode: ALT
100 UART5_TX_DATA_ALT0 — Selecting Pad: UART5_TX_DATA for Mode: ALT
101 UART5_RX_DATA_ALT0 — Selecting Pad: UART5_RX_DATA for Mode: ALT
But for the iMX6ULL:
000 CSI_DATA00_ALT8 — Selecting Pad: CSI_DATA00 for Mode: ALT8
001 CSI_DATA01_ALT8 — Selecting Pad: CSI_DATA01 for Mode: ALT8
010 GPIO1_IO04_ALT8 — Selecting Pad: GPIO1_IO04 for Mode: ALT8
011 GPIO1_IO05_ALT8 — Selecting Pad: GPIO1_IO05 for Mode: ALT
100 UART1_TX_DATA_ALT9 — Selecting Pad: UART1_TX_DATA for Mode: ALT9
101 UART1_RX_DATA_ALT9 — Selecting Pad: UART1_RX_DATA for Mode: ALT9
110 UART5_TX_DATA_ALT0 — Selecting Pad: UART5_TX_DATA for Mode: ALT0
111 UART5_RX_DATA_ALT0 — Selecting Pad: UART5_RX_DATA for Mode: ALT0
Specifically for a board I am working on with the serial console on UART5
I need to be able to enable UART5_RX_DATA_ALT0 mode. There is no definition
for the iMX6ULL version of that in imx6ul-pinfunc.h or imx6ull-pinfunc.h.
Add definitions for the missing UART5 input select register bits of the
iMX6ULL.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.CoreM6 1.5 is an another i.CoreM6 QDL cpu modules which can be connected
to EDIMM starter kit design with eMMC and MIPI-CSI interfaces suitable for
Android and video capture application.
notable features:
CPU NXP i.MX6 S/DL/D/Q, Up to 4 x Cortex-A9@800MHz
Memory Up to 2 GB DDR3-1066
Video Interfaces Up to 1 Parallel Up to 2 LVDS HDMI 1.4
port 8 bit CSI INPUT MIPI-CSI INPUT
1 x 10/100 Ethernet interface, 2 x USB, 1 x PCIe, 1 x I2S etc
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch to use koe_tx31d200vm0baa LVDS timings from
panel-simple instead hard coding the same in dts.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Handling of special clock operations on power domain on/off sequences
has been moved to respective Exynos clock controller drivers and clock
properties have been marked as deprecated. Remove all clock properties
from existing Exynos power domain nodes, as they are no longer used.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Modify audio related nodes to reflect the actual usage in binding documents.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In commit f0842bc563 ("ARM: dts: sun8i: h3: Enable HDMI output on H3
boards"), the hunk that enabled HDMI for the Orange Pi One did not add a
status = "okay";
line for the HDMI node, inadvertenly using the one for the EMAC. This
resulted in the EMAC now being disabled. Whether this was due to a
rebase error or some other mishap is unknown.
This patch re-enables the EMAC by adding the status line to its node.
Fixes: f0842bc563 ("ARM: dts: sun8i: h3: Enable HDMI output on H3 boards")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This new syntax is slightly better designed & uses "compatible" string.
For details see Documentation/devicetree/bindings/mtd/partition.txt .
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch adds the missing interrupt property to the RNG block
of BCM283x.
Link: https://github.com/raspberrypi/linux/issues/2195
CC: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add 'chosen' node with 'stdout-path' property to instruct kernel which
serial driver should be used for kernel console/logs. This allows to
enable earlycon messages by adding just 'earlycon' parameter to kernel
command line.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add support for USB OTG port on Insignal Origen Exynos4210-based evaluation
board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The size of these modules is 0x2000, not 0x3000. The extra 0x1000
after 0x2000 is for the interconnect target agent which is a separate
device.
Fixes: 7415b0b4c6 ("ARM: dts: omap4: add minimal l4 bus layout with
control module support")
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for the DH i.MX6 Quad based SoM and a PDK2 evaluation board.
The evaluation board features three serial ports, USB OTG, USB host with
an USB hub, Fast or Gigabit ethernet, eMMC, uSD, SD, mSATA, analog audio,
PCIe and HDMI video output.
All of the aforementioned features are supported by this patch.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The r8a7792 Wheat board has two ADV7513 devices sharing a single I2C
bus, however in low power mode the ADV7513 will reset it's slave maps to
use the hardware defined default addresses.
The ADV7511 driver was adapted to allow the two devices to be registered
correctly - but it did not take into account the fault whereby the
devices reset the addresses.
This results in an address conflict between the device using the default
addresses, and the other device if it is in low-power-mode.
Repair this issue by moving both devices away from the default address
definitions.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Fixes: f6eea82a87 ("ARM: dts: wheat: add DU support")
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for iWave iW-RainboW-G23S single board computer based on
RZ/G1C.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The initial R8A77470 SoC device tree including CPU0, GIC, timer, SYSC, RST,
CPG, and the required clock descriptions.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sort the subnodes of the soc node to improve maintainability.
The sort has been done alphabetically with the node name as the key.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The current practice is to not group clocks under a "clocks" subnode,
but just put them together with the other on-SoC devices.
As per updates for R-Car Gen2 SoCs by Geert Uytterhoeven.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort the subnodes of the soc node to improve maintainability.
The sort key is the address on the bus with instances of the same
IP block grouped together and sorted alphabetically.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add soc node to represent the bus and move all nodes with a base address
into this node. This is consistent with handling of R-Car Gen3 and Gen2
SoCs in mainline. It is intended to migrate other Renesas ARM-based
SoCs to this scheme.
The ordering is derived from simply moving each node with an address up to
before any nodes without a base address that occur before the soc node. To
improve maintainability follow-up patches will sort subnodes of both the
new soc node and the root node.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Move tempmon node from soc node to root node.
tempmon node does not have any register properties and thus
shouldn't be placed on the bus.
This fixes the following build warning with W=1:
arch/arm/boot/dts/imx7d-cl-som-imx7.dtb: Warning (simple_bus_reg): Node /soc/aips-bus@30000000/tempmon missing or empty reg/ranges property
Fixes: de25b9bb4a ("ARM: dts: imx7s: add temperature monitor support")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Andi Shyti