Move all possible setups for pio into SoC level DTSI file mt7623.dtsi in
order to introduce more boards such as official MT7623A reference boards
without copy-n-pasting almost the same content of nodes in pio into every
new file.
So, it should be better to reuse those nodes by consolidating them into
the common file mt7623.dtsi from the current existent DTS and allow new
DTS files to refer to them.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Since those LEDs are parts of PMIC MT6323, it is reasonable to merge
those LEDs node definition back into mt6323.dtsi. This way can improve
the reusability of those nodes among different boards with the same PMIC.
And LED is very much board specific and thus the mt6323.dtsi only includes
the parent node here and leave these child nodes in the board specific
dts file.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
add BTIF, HSDMA and SPI-NOR device nodes and enable it on relevant boards
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Fix below a lot of Warnings (unit_address_vs_reg) that dtc complains so
much for
Node /oscillator@1 has a unit name, but no reg property
Node /oscillator@0 has a unit name, but no reg property
Node /pinctrl@10005000/cir@0 has a unit name, but no reg property
Node /pinctrl@10005000/i2c@0 has a unit name, but no reg property
Node /pinctrl@10005000/i2c@1 has a unit name, but no reg property
Node /pinctrl@10005000/i2s@0 has a unit name, but no reg property
Node /pinctrl@10005000/i2s@1 has a unit name, but no reg property
Node /pinctrl@10005000/keys@0 has a unit name, but no reg property
Node /pinctrl@10005000/leds@0 has a unit name, but no reg property
Node /pinctrl@10005000/pwm@0 has a unit name, but no reg property
Node /pinctrl@10005000/spi@0 has a unit name, but no reg property
Node /pinctrl@10005000/uart@0 has a unit name, but no reg property
Node /pinctrl@10005000/uart@1 has a unit name, but no reg property
Node /pinctrl@10005000/uart@2 has a unit name, but no reg property
Node /ethernet@1b100000/mdio-bus/switch@0/ports has a reg or ranges
property, but no unit name
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
There is 2GB DDR3 available on bananapi-r2 board as [1] specified.
[1] http://www.banana-pi.org/r2.html
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Below two wrong nodes in existing DTS files would cause a fail boot since
in fact the address 0 is not the correct place the memory device locates
at.
memory {
device_type = "memory";
reg = <0x0 0x0 0x0 0x0>;
};
memory@80000000 {
reg = <0x0 0x80000000 0x0 0x40000000>;
};
In order to avoid having a memory node starting at address 0, we can't
include file skeleton64.dtsi and instead need to explicitly manually
define a few of properties the DTS relies on such as #address-cells
and #size-cells in root node and device_type in the node memory@80000000.
Cc: stable@vger.kernel.org
Fixes: 31ac0d69a1 ("ARM: dts: mediatek: add MT7623 basic support")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch adds some device nodes for the PCIe function block and updates
related pinmux.
Moreover, we add interrupt-map properties in both parent and children as
the chip only has one IRQ per slot that is connected to all INTx and get
propagated through the bridges and it also represents the root ports own
interrupts.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
It should be good that no use "_" is in DT node name. Consequently,
those nodes in certain files which have an inappropriate name containing
"_" are all being replaced with "-".
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The property pinctrl-names is totally superfluous. It would be good to
remove the property to keep the node neatness. There is actually
unnecessary to set up any pins for data path TRGMII between main SoC and
MT7530. Furthermore, it's more reasonable for the pin setup of control
path MDIO bus is being placed inside the node of ethernet controller.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
On bpi-r2 board, totally there're four UARTs which we usually called
uart[0-3] helpful to extend slow-I/O devices. Among those ones, uart2 has
dedicated pin slot which is used to console log. uart[0-1] appear at the
40-pins connector and uart3 has no pinout, but just has test points (TP47
for TX and TP48 for RX, respectively) nearby uart2, but we don't enable
uart3 in the patch. The missing pinctrl is also being supplemented for
those newly added devices.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Both mmc devices on bananapi-r2 board should all use the fixed regulators
as their power source instead of PMIC MT6323 exports.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Fix that USB initialization fails as below runtime log is present during
booting on bananapi-r2 board by adding missing regulators the USB device
requires. Current regulators USB device uses are being updated with the
correct ones to reflect real configurations which are all from fixed
regulators rather than MT6323 one's output.
xhci-mtk 1a1c0000.usb: 1a1c0000.usb supply vbus not found, using dummy regulator
xhci-mtk 1a240000.usb: 1a240000.usb supply vbus not found, using dummy regulator
Cc: stable@vger.kernel.org
Fixes: f4ff257cd1 ("arm: dts: mt7623: add support for Bananapi R2 (BPI-R2) board")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
[mb: update kernel log in commit message]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Fix that bananapi-r2 booting from SD-card would fail since incorrect
polarity is applied to the previous setup with GPIO_ACTIVE_HIGH.
Cc: stable@vger.kernel.org
Fixes: 0eed8d0976 ("arm: dts: mt7623: Add SD-card and EMMC to bananapi-r2")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Dummy patch to sort nodes alphabetically and add some blank lines
for consistency.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The bananapi-r2 board has an SD-card controller and built-in
EMMC storage so enables those devices in the devicetree.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add support for the Bananapi R2 (BPI-R2) development board from
BIPAI KEJI. Detailed hardware information for BPI-R2 which could be
found on http://www.banana-pi.org/r2.html
The patch added nodes into the SoC-level file mt7623.dtsi such as CPU OPP
table and thermal zone treating CPU as one of cooling devices and also
added nodes into board-level file mt7623n-bananapi-bpi-r2.dts such as
MediaTek GMAC, MT7530 Switch, the crypto engine, USB, IR, I2S, I2C, UART,
SPI, PWM, GPIO keys, GPIO LEDs and PMIC LEDs. As to the other missing
hardware and peripherals, they would be added and integrated continuously.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Sean Wang