We failed to initialize n_banks for spi-nor-generic flashes, which
caused a devide by zero when computing the bank_size.
By default we consider that all chips have a single bank. Initialize
the default number of banks for spi-nor-generic flashes. Even if the
bug is fixed with this simple initialization, check the n_banks value
before dividing so that we make sure this kind of bug won't occur again
if some other struct instance is created uninitialized.
Suggested-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Reported-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217448
Fixes: 9d6c5d64f0 ("mtd: spi-nor: Introduce the concept of bank")
Link: https://lore.kernel.org/all/20230516225108.29194-1-todd.e.brandt@intel.com/
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Tested-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230518085440.2363676-1-tudor.ambarus@linaro.org
* dt-bindings: Drop unneeded quotes
* mtdblock: Tolerate corrected bit-flips
* Use of_property_read_bool() for boolean properties
* Avoid magic values
* Avoid printing error messages on probe deferrals
* Prepare mtd_otp_nvmem_add() to handle -EPROBE_DEFER
* Fix error path for nvmem provider
* Fix nvmem error reporting
* Provide unique name for nvmem device
MTD device changes:
* lpddr_cmds: Remove unused words variable
* bcm63xxpart: Remove MODULE_LICENSE in non-modules
SPI NOR core changes:
* Introduce Read While Write support for flashes featuring several banks
* Set the 4-Byte Address Mode method based on SFDP data
* Allow post_sfdp hook to return errors
* Parse SCCR MC table and introduce support for multi-chip devices
SPI NOR manufacturer drivers changes:
* macronix: Add support for mx25uw51245g with RWW
* spansion:
- Determine current address mode at runtime as it can be changed in a
non-volatile way and differ from factory defaults or from what SFDP
advertises.
- Enable JFFS2 write buffer mode for few ECC'd NOR flashes: S25FS256T,
s25hx and s28hx
- Add support for s25hl02gt and s25hs02gt
Raw NAND core changes:
* Convert to platform remove callback returning void
* Fix spelling mistake waifunc() -> waitfunc()
Raw NAND controller driver changes:
* imx: Remove unused is_imx51_nfc and imx53_nfc functions
* omap2: Drop obsolete dependency on COMPILE_TEST
* orion: Use devm_platform_ioremap_resource()
* qcom:
- Use of_property_present() for testing DT property presence
- Use devm_platform_get_and_ioremap_resource()
* stm32_fmc2: Depends on ARCH_STM32 instead of MACH_STM32MP157
* tmio: Remove reference to config MTD_NAND_TMIO in the parsers
Raw NAND manufacturer driver changes:
* hynix: Fix up bit 0 of sdr_timing_mode
SPI-NAND changes:
* Add support for ESMT F50x1G41LB
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmRANmIACgkQJWrqGEe9
VoRU2QgAl8XFkLs1h88wGi6ln/MSK0cQJZWUzteGgWuaBQCMNfgGFzqPHyJ7ygO9
l4U4O1L/IvACvJx5QHm/lH5Mig23jym9J8YfV1Kf9aVYOlBKRNysbi+DdktESGG9
6HmpS0nQfkC84qA8ouInOp+AZYjFEPRrBfp5UWkSRHiQJvcYnt2iS2oOLk3LNY6y
zduBOno3mric2ZlBbg+ZCURhQzrr3k8c4VXV+LHSslqsmH/2sOFlg78hLJx922Y+
FTfYnx82iLIvFAJttRi2bXWKuE1Yr2XWJ3iEHKxmOA2vPmYi6mDBHTYhnikGSpm+
GhARHH+JhW7qzLbaq5ZC3HGH58aC/g==
=aYlo
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"Core MTD changes:
- dt-bindings: Drop unneeded quotes
- mtdblock: Tolerate corrected bit-flips
- Use of_property_read_bool() for boolean properties
- Avoid magic values
- Avoid printing error messages on probe deferrals
- Prepare mtd_otp_nvmem_add() to handle -EPROBE_DEFER
- Fix error path for nvmem provider
- Fix nvmem error reporting
- Provide unique name for nvmem device
MTD device changes:
- lpddr_cmds: Remove unused words variable
- bcm63xxpart: Remove MODULE_LICENSE in non-modules
SPI NOR core changes:
- Introduce Read While Write support for flashes featuring several
banks
- Set the 4-Byte Address Mode method based on SFDP data
- Allow post_sfdp hook to return errors
- Parse SCCR MC table and introduce support for multi-chip devices
SPI NOR manufacturer drivers changes:
- macronix: Add support for mx25uw51245g with RWW
- spansion:
- Determine current address mode at runtime as it can be changed
in a non-volatile way and differ from factory defaults or from
what SFDP advertises.
- Enable JFFS2 write buffer mode for few ECC'd NOR flashes:
S25FS256T, s25hx and s28hx
- Add support for s25hl02gt and s25hs02gt
Raw NAND core changes:
- Convert to platform remove callback returning void
- Fix spelling mistake waifunc() -> waitfunc()
Raw NAND controller driver changes:
- imx: Remove unused is_imx51_nfc and imx53_nfc functions
- omap2: Drop obsolete dependency on COMPILE_TEST
- orion: Use devm_platform_ioremap_resource()
- qcom:
- Use of_property_present() for testing DT property presence
- Use devm_platform_get_and_ioremap_resource()
- stm32_fmc2: Depends on ARCH_STM32 instead of MACH_STM32MP157
- tmio: Remove reference to config MTD_NAND_TMIO in the parsers
Raw NAND manufacturer driver changes:
- hynix: Fix up bit 0 of sdr_timing_mode
SPI-NAND changes:
- Add support for ESMT F50x1G41LB"
* tag 'mtd/for-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (55 commits)
mtd: nand: Convert to platform remove callback returning void
mtd: onenand: omap2: Drop obsolete dependency on COMPILE_TEST
mtd: spi-nor: spansion: Add support for s25hl02gt and s25hs02gt
mtd: spi-nor: spansion: Add a new ->ready() hook for multi-chip device
mtd: spi-nor: spansion: Rework cypress_nor_quad_enable_volatile() for multi-chip device support
mtd: spi-nor: spansion: Rework cypress_nor_get_page_size() for multi-chip device support
mtd: spi-nor: sfdp: Add support for SCCR map for multi-chip device
mtd: spi-nor: Extract volatile register offset from SCCR map
mtd: spi-nor: Allow post_sfdp hook to return errors
mtd: spi-nor: spansion: Rename method to cypress_nor_get_page_size
mtd: spi-nor: spansion: Enable JFFS2 write buffer for S25FS256T
mtd: spi-nor: spansion: Enable JFFS2 write buffer for Infineon s25hx SEMPER flash
mtd: spi-nor: spansion: Enable JFFS2 write buffer for Infineon s28hx SEMPER flash
mtd: spi-nor: spansion: Determine current address mode
mtd: spi-nor: core: Introduce spi_nor_set_4byte_addr_mode()
mtd: spi-nor: core: Update flash's current address mode when changing address mode
mtd: spi-nor: Stop exporting spi_nor_restore()
mtd: spi-nor: Set the 4-Byte Address Mode method based on SFDP data
mtd: spi-nor: core: Make spi_nor_set_4byte_addr_mode_brwr public
mtd: spi-nor: core: Update name and description of spi_nor_set_4byte_addr_mode
...
Infineon(Cypress) SEMPER NOR flash family has on-die ECC and its program
granularity is 16-byte ECC data unit size. JFFS2 supports write buffer
mode for ECC'd NOR flash. Provide a way to clear the MTD_BIT_WRITEABLE
flag in order to enable JFFS2 write buffer mode support.
A new SNOR_F_ECC flag is introduced to determine if the part has on-die
ECC and if it has, MTD_BIT_WRITEABLE is unset.
In vendor specific driver, a common cypress_nor_ecc_init() helper is
added. This helper takes care for ECC related initialization for SEMPER
flash family by setting up params->writesize and SNOR_F_ECC.
Fixes: c3266af101 ("mtd: spi-nor: spansion: add support for Cypress Semper flash")
Suggested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/d586723f6f12aaff44fbcd7b51e674b47ed554ed.1680760742.git.Takahiro.Kuwano@infineon.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Make the method public, as it will be used as a last resort to enable
4byte address mode when we can't determine the address mode at runtime.
Update the addr_nbytes and current address mode while exiting the 4byte
address mode too, as it may be used in the future by manufacturer
drivers. No functional change. spi_nor_restore didn't update the address
mode nbytes, but updating them now doesn't harm as the method is called
in the driver's remove and shutdown paths.
Link: https://lore.kernel.org/r/20230331074606.3559258-10-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
The bug was obswerved while reading code. There are not many users of
addr_mode_nbytes. Anyway, we should update the flash's current address
mode when changing the address mode, fix it. We don't care for now about
the set_4byte_addr_mode(nor, false) from spi_nor_restore(), as it is
used at driver remove and shutdown.
Fixes: d7931a2150 ("mtd: spi-nor: core: Track flash's internal address mode")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230331074606.3559258-9-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Some SPI NOR controllers that used this method were moved to
drivers/spi/. We don't accept new support for the existing SPI NOR
controllers drivers under drivers/mtd/spi-nor/controllers/ and we
encourage their owners to move the drivers under drivers/spi/.
Make spi_nor_restore() private as we're going to use it just in core.c.
Link: https://lore.kernel.org/r/20230331074606.3559258-8-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
JESD216 SFDP defines in BFPT methods to enter and exit the
4-Byte Address Mode. The flash parameters and settings that are
retrieved from SFDP have higher precedence than the static
initialized ones, because they should be more accurate and less
error prone than those initialized statically. Parse and favor the
BFPT-parsed set_4byte_addr_mode methods.
Some regressions may be introduced by this patch, because the
params->set_4byte_addr_mode method that was set either in
spi_nor_init_default_params() or later overwritten in default_init()
hooks, are now be overwritten with a different value based on the
BFPT data. If that's the case, the fix is to introduce a post_bfpt
fixup hook where one should fix the wrong BFPT info.
Link: https://lore.kernel.org/r/20230331074606.3559258-7-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
This method can be retrieved at BFPT parsing time. The method is
described in JESD216 BFPT[SFDP_DWORD(16)], BIT(28) and BIT(20).
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20230331074606.3559258-6-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Rename method to spi_nor_set_4byte_addr_mode_en4b_ex4b and extend its
description. This method is described in JESD216 BFPT[SFDP_DWORD(16)],
BIT(31) and BIT(23).
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20230331074606.3559258-5-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Rename method to spi_nor_set_4byte_addr_mode_brwr and extend its
description. This method is described in JESD216 BFPT[SFDP_DWORD(16)],
BIT(28) and BIT(20).
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20230331074606.3559258-4-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Rename method to spi_nor_set_4byte_addr_mode_wren_en4b_ex4b and extend
its description. This method is described in JESD216 BFPT[SFDP_DWORD(16)],
BIT(30) and BIT(22).
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20230331074606.3559258-3-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Bank size is derived from the chip's size, which in
spi_nor_init_default_params() can still be zero if the flash size is
not specified at flash declaration. Let the flash size be updated
by parsing SFDP and do the initialization of the bank size in
spi_nor_late_init_params(). Flashes that don't define the SFDP tables
must specify the flash size at declaration.
Fixes: 9d6c5d64f0 ("mtd: spi-nor: Introduce the concept of bank")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230331194620.839899-1-miquel.raynal@bootlin.com
[ta: drop superfluous initialization in spi_nor_init_default_params(),
reword commit message, add Fixes tag.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
On devices featuring several banks, the Read While Write (RWW) feature
is here to improve the overall performance when performing parallel
reads and writes at different locations (different banks). The following
constraints have to be taken into account:
1#: A single operation can be performed in a given bank.
2#: Only a single program or erase operation can happen on the entire
chip (common hardware limitation to limit costs)
3#: Reads must remain serialized even though reads crossing bank
boundaries are allowed.
4#: The I/O bus is unique and thus is the most constrained resource, all
spi-nor operations requiring access to the spi bus (through the spi
controller) must be serialized until the bus exchanges are over. So
we must ensure a single operation can be "sent" at a time.
5#: Any other operation that would not be either a read or a write or an
erase is considered requiring access to the full chip and cannot be
parallelized, we then need to ensure the full chip is in the idle
state when this occurs.
All these constraints can easily be managed with a proper locking model:
1#: Is enforced by a bitfield of the in-use banks, so that only a single
operation can happen in a specific bank at any time.
2#: Is handled by the ongoing_pe boolean which is set before any write
or erase, and is released only at the very end of the
operation. This way, no other destructive operation on the chip can
start during this time frame.
3#: An ongoing_rd boolean allows to track the ongoing reads, so that
only one can be performed at a time.
4#: An ongoing_io boolean is introduced in order to capture and serialize
bus accessed. This is the one being released "sooner" than before,
because we only need to protect the chip against other SPI accesses
during the I/O phase, which for the destructive operations is the
beginning of the operation (when we send the command cycles and
possibly the data), while the second part of the operation (the
erase delay or the programmation delay) is when we can do something
else in another bank.
5#: Is handled by the three booleans presented above, if any of them is
set, the chip is not yet ready for the operation and must wait.
All these internal variables are protected by the existing lock, so that
changes in this structure are atomic. The serialization is handled with
a wait queue.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230328154105.448540-8-miquel.raynal@bootlin.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Introduce a new (no SFDP) flag for the feature that we are about to
support: Read While Write. This means, if the chip has several banks and
supports RWW, once a page of data to write has been transferred into the
chip's internal SRAM, another read operation happening on a different
bank can be performed during the tPROG delay.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230328154105.448540-7-miquel.raynal@bootlin.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
This commit alone just introduces two new "prepare and lock" pairs of
helpers which do the exact same thing as before. They will soon be
improved in a followup commit which actually brings the logic, but I
figured out it was more readable to do it this way.
One new pair is suffixed _pe which stands for "program and erase" and
hence is being called by spi_nor_write() and spi_nor_erase().
The other pair is suffixed _rd which stands for "read" and hence is
being called by spi_nor_read().
One note however, these extra helpers will need to know the operation
range, so they come with two new parameters to define it. Otherwise
there is no functional change.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230328154105.448540-6-miquel.raynal@bootlin.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
While this operation will remain a single function call in the end,
let's extract the logic of the [un]prepare calls within their own static
helper. We will soon add new flavors of the *_[un]prepare_and_[un]lock()
helpers, having the preparation logic outside will save us from duplicating
code over and over again.
There is no functional change.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230328154105.448540-5-miquel.raynal@bootlin.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
The ->prepare()/->unprepare() hooks are now legacy, we no longer accept
new drivers supporting them. The only remaining controllers using them
acquires a per-chip mutex, which should not interfere with the rest of
the operation done in the core. As a result, we should be safe to
reorganize these helpers to first perform the preparation, before
acquiring the core locks. This is necessary in order to be able to
improve the locking mechanism in the core (coming next). No side effects
are expected.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230328154105.448540-4-miquel.raynal@bootlin.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
SPI NOR chips are made of pages, which gathered in small groups make
(erase) sectors. Sectors, gathered together, make banks inside the
chip. Until now, there was only one bank per device supported, but we
are about to introduce support for new chips featuring several banks (up
to 4 so far) where different operations may happen in parallel.
Let's allow describing these additional bank parameters, and let's do
this independently of any other value (like the number of sectors) with
an absolute value.
By default we consider that all chips have a single bank.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20230328154105.448540-2-miquel.raynal@bootlin.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To solve this, remove the
lookup and create the directory on the first device found, and then
remove it when the module is unloaded.
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: Pratyush Yadav <pratyush@kernel.org>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20230208160230.2179905-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sort headers alphabetically - it helps locating duplicates, and makes it
easier to figure out where to insert new headers. Alphabetic order should
also prove that each header is self-contained, i.e. can be included without
prerequisites.
Link: https://lore.kernel.org/r/20230202144628.14443-1-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
spi_nor_set_erase_type() was used either to set or to mask out an erase
type. When we used it to mask out an erase type a shift-out-of-bounds
was hit:
UBSAN: shift-out-of-bounds in drivers/mtd/spi-nor/core.c:2237:24
shift exponent 4294967295 is too large for 32-bit type 'int'
The setting of the size_{shift, mask} and of the opcode are unnecessary
when the erase size is zero, as throughout the code just the erase size
is considered to determine whether an erase type is supported or not.
Setting the opcode to 0xFF was wrong too as nobody guarantees that 0xFF
is an unused opcode. Thus when masking out an erase type, just set the
erase size to zero. This will fix the shift-out-of-bounds.
Fixes: 5390a8df76 ("mtd: spi-nor: add support to non-uniform SFDP SPI NOR flash memories")
Cc: stable@vger.kernel.org
Reported-by: Alexander Stein <Alexander.Stein@tq-group.com>
Signed-off-by: Louis Rannou <lrannou@baylibre.com>
Tested-by: Alexander Stein <Alexander.Stein@tq-group.com>
Link: https://lore.kernel.org/r/20230203070754.50677-1-tudor.ambarus@linaro.org
[ta: refine changes, new commit message, fix compilation error]
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
spi-nor/core.c needs to include linux/delay.h,
or it would raise below compile warning:
drivers/mtd/spi-nor/core.c: In function ‘spi_nor_soft_reset’:
drivers/mtd/spi-nor/core.c:2779:2: error: implicit declaration of function ‘usleep_range’ [-Werror=implicit-function-declaration]
2779 | usleep_range(SPI_NOR_SRST_SLEEP_MIN, SPI_NOR_SRST_SLEEP_MAX);
| ^~~~~~~~~~~~
Fixes: d73ee7534c ("mtd: spi-nor: core: perform a Soft Reset on shutdown")
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20220923031457.56103-1-zengheng4@huawei.com
* Add support for flash reset using the dt reset-gpios property.
* Update hwcaps.mask to include 8D-8D-8D read and page program ops
when xSPI profile 1.0 table is defined.
* Bypass zero erase size in spi_nor_find_best_erase_type().
* Fix select_uniform_erase to skip 0 erase size
* Add generic flash driver. If a flash is not found in the flash_info
array, fall back to the generic flash driver which is described solely
by the flash's SFDP tables.
* Fix the number of bytes for the dummy cycles in
spi_nor_spimem_check_readop().
* Introduce SPI_NOR_QUAD_PP flag, as PP_1_1_4 is not SFDP discoverable.
SPI NOR manufacturer drivers changes:
* Spansion:
- use PARSE_SFDP for s28hs512t,
- add support for s28hl512t, s28hl01gt, and s28hs01gt.
* Gigadevice: Replace default_init() with post_bfpt() for gd25q256.
* Micron - ST: Enable locking for mt25qu256a.
* Winbond: Add support for W25Q512NW-IQ.
* ISSI: Use PARSE_SFDP and SPI_NOR_QUAD_PP.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmOJ59AACgkQS1VPR6WN
FOnzOQf/WLBTNFtPcJoS7cdjlh4fuGySDUKuLifOX+Tmk/ki3XFCZR98cESgb5m+
hCyFDeER/qfdOK9ObT3K1GBS6x7zx8YkskbucjAU0vlIsr2ZHCjNpNiAHrADsKjR
579N0Xwh2ibh7uVJ1xvsPwObdAc8P/tjGHHWF6hGEZzIPYXJVce+qDktkkLfbZ/P
Fik6+y3h68wW/0kDNt/gNmNcb5Z3fjxySs21Np5sy7bUtVVBjHWLo0OpjNadDH9M
m6AkhFA5h9OVl5E4jHBpxc4NvlAa5f6520vESpieseNJiIMWo0W/eSkVsframFew
ILdtXCHjkbS6kgvSpUViobMFsgCjaA==
=Yi2q
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-6.2' into mtd/next
SPI NOR core changes:
* Add support for flash reset using the dt reset-gpios property.
* Update hwcaps.mask to include 8D-8D-8D read and page program ops
when xSPI profile 1.0 table is defined.
* Bypass zero erase size in spi_nor_find_best_erase_type().
* Fix select_uniform_erase to skip 0 erase size
* Add generic flash driver. If a flash is not found in the flash_info
array, fall back to the generic flash driver which is described solely
by the flash's SFDP tables.
* Fix the number of bytes for the dummy cycles in
spi_nor_spimem_check_readop().
* Introduce SPI_NOR_QUAD_PP flag, as PP_1_1_4 is not SFDP discoverable.
SPI NOR manufacturer drivers changes:
* Spansion:
- use PARSE_SFDP for s28hs512t,
- add support for s28hl512t, s28hl01gt, and s28hs01gt.
* Gigadevice: Replace default_init() with post_bfpt() for gd25q256.
* Micron - ST: Enable locking for mt25qu256a.
* Winbond: Add support for W25Q512NW-IQ.
* ISSI: Use PARSE_SFDP and SPI_NOR_QUAD_PP.
Fix merge conflict in the jedec,spi-nor bindings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SFDP table of some flash chips do not advertise support of Quad Input
Page Program even though it has support. Use flags and add hardware
cap for these chips.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@sifive.com>
[tudor.ambarus@microchip.com: move pp setting in spi_nor_init_default_params]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220920184808.44876-2-sudip.mukherjee@sifive.com
The number of bytes used by spi_nor_spimem_check_readop() may be
incorrect for the dummy cycles. Since nor->read_dummy is not initialized
before spi_nor_spimem_adjust_hwcaps().
We use both mode and wait state clock cycles instead of nor->read_dummy.
Fixes: 0e30f47232 ("mtd: spi-nor: add support for DTR protocol")
Co-developed-by: Bayi Cheng <bayi.cheng@mediatek.com>
Signed-off-by: Bayi Cheng <bayi.cheng@mediatek.com>
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Dhruva Gole <d-gole@ti.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20221031124633.13189-1-allen-kh.cheng@mediatek.com
Our SFDP parsing is everything we need to support all basic operations
of a flash device. If the flash isn't found in our in-kernel flash
database, gracefully fall back to a driver described solely by its SFDP
tables.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-7-michael@walle.cc
4bait will set the erase size to 0 if there is no corresponding
opcode for the 4byte erase. Fix spi_nor_select_uniform_erase to skip
the 0 erase size to avoid mtd device registration failure cases.
Reported-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-6-michael@walle.cc
At the moment, we print the JEDEC ID that is stored in our database. The
generic flash support won't have such an entry in our database. To find
out the JEDEC ID later we will have to cache it. There is also another
advantage: If the flash is found in the database, the ID could be
truncated because the ID of the entry is used which can be shorter. Some
flashes still holds valuable information in the bytes after the JEDEC ID
and come in handy during debugging of when coping with INFO6() entries.
These are not accessible for now.
Save a copy of the ID bytes after reading and display it via debugfs.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-4-michael@walle.cc
Erase can be zeroed in spi_nor_parse_4bait() or
spi_nor_init_non_uniform_erase_map(). In practice it happened with
mt25qu256a, which supports 4K, 32K, 64K erases with 3b address commands,
but only 4K and 64K erase with 4b address commands.
Fixes: dc92843159 ("mtd: spi-nor: fix erase_type array to indicate current map conf")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211119081412.29732-1-alexander.sverdlin@nokia.com
Add an error message when failing to exit the 4-byte address mode. Do not
stop the execution and go through the spi_nor_soft_reset() method if used,
in the hope that the flash will default to 3-byte address mode after the
reset.
Suggested-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220728030159.68680-1-tudor.ambarus@microchip.com
Add support for spi-nor flash reset via GPIO controller by reading the
reset-gpio property. If there is a valid GPIO specifier then reset will
be performed by asserting and deasserting the GPIO using gpiod APIs
otherwise it will not perform any operation.
Signed-off-by: Sai Krishna Potthuri <sai.krishna.potthuri@amd.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220908064428.2962-3-sai.krishna.potthuri@amd.com
The Intel SPI-NOR controller does not support the 4-byte address opcode
so ->set_4byte_addr_mode() ends up returning -ENOTSUPP and the SPI flash
chip probe fail like this:
[ 12.291082] spi-nor: probe of spi0.0 failed with error -524
Whereas previously before commit 08412e72af ("mtd: spi-nor: core:
Return error code from set_4byte_addr_mode()") it worked just fine.
Fix this by ignoring -ENOTSUPP in spi_nor_init().
Fixes: 08412e72af ("mtd: spi-nor: core: Return error code from set_4byte_addr_mode()")
Cc: stable@vger.kernel.org
Reported-by: Hongyu Ning <hongyu.ning@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220923093441.3178-1-mika.westerberg@linux.intel.com
For erase operations, reg_proto must be used as indicated in
struct spi_nor description in spi-nor.h.
This issue was found when DT property spi-tx-bus-width is set to 4.
In this case the spi_mem_op->addr.buswidth is set to 4 for erase command
which is not correct.
Tested on stm32mp157c-ev1 board with mx66l51235f spi-nor.
Fixes: 0e30f47232 ("mtd: spi-nor: add support for DTR protocol")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
[ta: use nor->reg_proto in spi_nor_controller_ops_erase()]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220629133013.3382393-1-patrice.chotard@foss.st.com
The prams->set_4byte_addr_mode returns error code but is not handled
in spi_nor_init(). Handle the return code from set_4byte_addr_mode().
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220725092505.446315-5-tudor.ambarus@microchip.com
At the SFDP parsing time we should not change members of struct spi_nor,
but instead fill members of struct spi_nor_flash_parameters which could
later on be used by callers. The caller will then decide if SFDP params
should be used and more importantly when they should be used. Clean the
code flow and don't initialize nor->addr_nbytes at SFDP parsing time.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220725092505.446315-4-tudor.ambarus@microchip.com
Address width was an unfortunate name, as it means the number of IO lines
used for the address, whereas in the code it is used as the number of
address bytes. s/addr_width/addr_nbytes throughout the entire SPI NOR
framework.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220725092505.446315-2-tudor.ambarus@microchip.com
The SECT_4K_PMC flag will set a device specific opcode for the 4k sector
erase. Instead of handling it in the core, we can move it to a
late_init(). In that late init, loop over all erase types, look for the
4k size and replace the opcode.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220418112650.2791459-1-michael@walle.cc
There is no way to gather all information to verify support for a new
flash chip. Also if you want to convert an existing flash chip to the
new SFDP parsing, there is not enough information to determine if the
flash will work like before. To ease this development, expose internal
parameters via the debugfs.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220429102018.2361038-2-michael@walle.cc
The "Extended Address Register" is winbond specific. If the flash is
larger than 16MiB and is used in 3 byte address mode, it is used to set
the remaining address bits. Move the write_ear() function, the opcode
macros and the spimem op template into the winbond module and rename
them accordingly.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220429100153.2338501-1-michael@walle.cc
Clean the op declaration and hide the details of each op. With this it
results a cleanner, easier to read code. No functional change expected.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Michael Walle <michael@walle.cc>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220420103427.47867-10-tudor.ambarus@microchip.com
There are manufacturers that use registers indexed by address. Some of
them support "read/write any register" opcodes. Provide core methods that
can be used by all manufacturers. SPI NOR controller ops are intentionally
not supported as we intend to move all the SPI NOR controller drivers
under the SPI subsystem.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Tested-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-7-tudor.ambarus@microchip.com
RDID is used in the core to auto detect the flash, but also by some
manufacturer drivers that contain flashes that support Octal DTR mode,
so that they can read the flash ID after the switch to Octal DTR was made
to test if the switch was successful. Introduce a core method for RDID op
to avoid code duplication.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-5-tudor.ambarus@microchip.com
In case spi_nor_match_name() returned NULL, the auto detection was
issued twice. There's no reason to try to detect the same chip twice,
do the auto detection only once.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-4-tudor.ambarus@microchip.com
Similar to spi_nor_match_name() extend the search of flash_info through
all the manufacturers, this time doing the match by ID. There's no reason
to limit the search per manufacturer yet, do it globally, search the flash
in all the parts of all manufacturers in a single method.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-3-tudor.ambarus@microchip.com
The method is matching a flash_info entry by searching by name. Rename
the method for better clarity.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-2-tudor.ambarus@microchip.com
Read back Status Register 1 to ensure that the written byte match the
received value and return -EIO if read back test failed.
Without this patch, spi_nor_write_16bit_sr_and_check() only check the
second half of the 16bit. It causes errors like spi_nor_sr_unlock()
return success incorrectly when spi_nor_write_16bit_sr_and_check()
doesn't write SR successfully.
Fixes: 39d1e3340c ("mtd: spi-nor: Fix clearing of QE bit on lock()/unlock()")
Signed-off-by: Chen-Tsung Hsieh <chentsung@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220126073227.3401275-1-chentsung@chromium.org
Even if SPI_NOR_NO_ERASE was set, one could still send erase opcodes
to the flash. It is not recommended to send unsupported opcodes to
flashes. Fix the logic and do not set mtd->_erase when SPI_NOR_NO_ERASE
is specified. With this users will not be able to issue erase opcodes to
flashes and instead they will recive an -ENOTSUPP error.
Fixes: b199489d37 ("mtd: spi-nor: add the framework for SPI NOR")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220228163334.277730-1-tudor.ambarus@microchip.com
Tudor Ambarus