We have so far ignored the memory errors, assuming that we have perfect
hardware and driver. Let us handle the memory errors reported by the
TMC ETR in status and truncate the buffer.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[Removed ASCII smiley face from changelog]
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20190829202842.580-6-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We now use refcounts for the etr_buf users. Let us initialize it
while we allocate it.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20190829202842.580-5-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for coresight CPU debug module on Qualcomm
Kryo CPUs. This patch adds the UCI entries for Kryo CPUs
found on MSM8996 which shares the same PIDs as ETMs.
Without this, below error is observed on MSM8996:
[ 5.429867] OF: graph: no port node found in /soc/debug@3810000
[ 5.429938] coresight-etm4x: probe of 3810000.debug failed with error -22
[ 5.435415] coresight-cpu-debug 3810000.debug: Coresight debug-CPU0 initialized
[ 5.446474] OF: graph: no port node found in /soc/debug@3910000
[ 5.448927] coresight-etm4x: probe of 3910000.debug failed with error -22
[ 5.454681] coresight-cpu-debug 3910000.debug: Coresight debug-CPU1 initialized
[ 5.487765] OF: graph: no port node found in /soc/debug@3a10000
[ 5.488007] coresight-etm4x: probe of 3a10000.debug failed with error -22
[ 5.493024] coresight-cpu-debug 3a10000.debug: Coresight debug-CPU2 initialized
[ 5.501802] OF: graph: no port node found in /soc/debug@3b10000
[ 5.512901] coresight-etm4x: probe of 3b10000.debug failed with error -22
[ 5.513192] coresight-cpu-debug 3b10000.debug: Coresight debug-CPU3 initialized
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20190829202842.580-4-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of overriding the peripheral id(PID) check in AMBA
by hardcoding them in DT, add the PIDs to the ETM4x driver.
Here we use Unique Component Identifier(UCI) for MSM8996
since the ETM and CPU debug module shares the same PIDs.
SDM845 does not support CPU debug module.
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20190829202842.580-3-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid an extra function call in two function implementations
by using a ternary operator instead of a conditional statement.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20190829202842.580-2-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While running the linux-next with CONFIG_DEBUG_LOCKS_ALLOC enabled,
I get the following splat.
BUG: key ffffcb5636929298 has not been registered!
------------[ cut here ]------------
DEBUG_LOCKS_WARN_ON(1)
WARNING: CPU: 1 PID: 53 at kernel/locking/lockdep.c:3669 lockdep_init_map+0x164/0x1f0
CPU: 1 PID: 53 Comm: kworker/1:1 Tainted: G W 5.2.0-next-20190712-00015-g00ad4634222e-dirty #603
Workqueue: events amba_deferred_retry_func
pstate: 60c00005 (nZCv daif +PAN +UAO)
pc : lockdep_init_map+0x164/0x1f0
lr : lockdep_init_map+0x164/0x1f0
[ trimmed ]
Call trace:
lockdep_init_map+0x164/0x1f0
__kernfs_create_file+0x9c/0x158
sysfs_add_file_mode_ns+0xa8/0x1d0
sysfs_add_file_to_group+0x88/0xd8
etm_perf_add_symlink_sink+0xcc/0x138
coresight_register+0x110/0x280
tmc_probe+0x160/0x420
[ trimmed ]
---[ end trace ab4cc669615ba1b0 ]---
Fix this by initialising the dynamically allocated attribute properly.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Fixes: bb8e370bdc ("coresight: perf: Add "sinks" group to PMU directory")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[Fixed a typograhic error in the changelog]
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20190801172323.18359-2-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Those are due to recent changes. Most of the issues
can be automatically fixed with:
$ ./scripts/documentation-file-ref-check --fix
The only exception was the sound binding with required
manual work.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add a helper to match the firmware node handle of a device and provide
wrappers for {bus/class/driver}_find_device() APIs to avoid proliferation
of duplicate custom match functions.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-usb@vger.kernel.org
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Joe Perches <joe@perches.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190723221838.12024-4-suzuki.poulose@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix Linus' merge error in the parent commit, causing:
drivers/hwtracing/coresight/coresight.c:1051:11: error: incompatible pointer types passing 'int (struct device *, void *)' to parameter of type 'int (*)(struct device *, const void *)' [-Werror,-Wincompatible-pointer-types]
coresight_device_fwnode_match);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/device.h:173:17: note: passing argument to parameter 'match' here
int (*match)(struct device *dev, const void *data));
^
due to missed header file fixup.
Fixes: f632a8170a ("Merge tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
[ Greg even sent this patch with his pull request, but I stupidly
thought it was the merge resolution fix I had already done as part of
the merge. But no, this was the extra fix for the header file
that goes with the definition I _had_ caught - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups. Because of this, there is going
to be some merge issues with your tree at the moment, I'll follow up
with the expected resolutions to make it easier for you.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups (will cause build warnings
with s390 and coresight drivers in your tree)
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse
easier due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of merge
issues that Stephen has been patient with me for. Other than the merge
issues, functionality is working properly in linux-next :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSgpnQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykcwgCfS30OR4JmwZydWGJ7zK/cHqk+KjsAnjOxjC1K
LpRyb3zX29oChFaZkc5a
=XrEZ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse easier
due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of
merge issues that Stephen has been patient with me for"
* tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (102 commits)
debugfs: make error message a bit more verbose
orangefs: fix build warning from debugfs cleanup patch
ubifs: fix build warning after debugfs cleanup patch
driver: core: Allow subsystems to continue deferring probe
drivers: base: cacheinfo: Ensure cpu hotplug work is done before Intel RDT
arch_topology: Remove error messages on out-of-memory conditions
lib: notifier-error-inject: no need to check return value of debugfs_create functions
swiotlb: no need to check return value of debugfs_create functions
ceph: no need to check return value of debugfs_create functions
sunrpc: no need to check return value of debugfs_create functions
ubifs: no need to check return value of debugfs_create functions
orangefs: no need to check return value of debugfs_create functions
nfsd: no need to check return value of debugfs_create functions
lib: 842: no need to check return value of debugfs_create functions
debugfs: provide pr_fmt() macro
debugfs: log errors when something goes wrong
drivers: s390/cio: Fix compilation warning about const qualifiers
drivers: Add generic helper to match by of_node
driver_find_device: Unify the match function with class_find_device()
bus_find_device: Unify the match callback with class_find_device
...
Coresight platform support assumes that a missing "cpu" phandle
defaults to CPU0. This could be problematic and unnecessarily binds
components to CPU0, where they may not be. In coresight etm and
cpu-debug drivers, abort the probe for such cases.
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/f1955ea19c714cf64ea54ec356a9aa85f3cd17b8.1562229018.git.saiprakash.ranjan@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on the following report from Smatch, fix the potential
NULL pointer dereference check.
The patch 743256e214e8: "coresight: tmc: Clean up device specific
data" from May 22, 2019, leads to the following Smatch complaint:
drivers/hwtracing/coresight/coresight-tmc-etr.c:625 tmc_etr_free_flat_buf()
warn: variable dereferenced before check 'flat_buf' (see line 623)
drivers/hwtracing/coresight/coresight-tmc-etr.c
622 struct etr_flat_buf *flat_buf = etr_buf->private;
623 struct device *real_dev = flat_buf->dev->parent;
^^^^^^^^^^
The patch introduces a new NULL check
624
625 if (flat_buf && flat_buf->daddr)
^^^^^^^^
but the existing code assumed it can be NULL.
626 dma_free_coherent(real_dev, flat_buf->size,
627 flat_buf->vaddr, flat_buf->daddr);
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20190621175205.24551-3-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on the following report from Smatch tool, make sure we have a
valid drvdata before we dereference it to find the real dev.
The patch 21d26b905c05: "coresight: etm: Clean up device specific
data" from May 22, 2019, leads to the following Smatch complaint:
./drivers/hwtracing/coresight/coresight-etm3x.c:460 etm_get_trace_id()
warn: variable dereferenced before check 'drvdata' (see line 458)
./drivers/hwtracing/coresight/coresight-etm3x.c
457 int trace_id = -1;
458 struct device *etm_dev = drvdata->csdev->dev.parent;
^^^^^^^^^
New dereference
459
460 if (!drvdata)
^^^^^^^^
Checked too late. Delete the check?
461 goto out;
462
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20190621175205.24551-2-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "drvdata->atclk" clock is optional, but if it gets set to an error
pointer then we're accidentally return an uninitialized variable instead
of success.
Fixes: 78e6427b4e ("coresight: funnel: Support static funnel")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190620221237.3536-6-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During a perf session we try to allocate buffers on the "node" associated
with the CPU the event is bound to. If it is not bound to a CPU, we
use the current CPU node, using smp_processor_id(). However this is unsafe
in a pre-emptible context and could generate the splats as below :
BUG: using smp_processor_id() in preemptible [00000000] code: perf/2544
Use NUMA_NO_NODE hint instead of using the current node for events
not bound to CPUs.
Fixes: 2997aa4063 ("coresight: etb10: implementing AUX API")
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: stable <stable@vger.kernel.org> # 4.6+
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20190620221237.3536-5-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During a perf session we try to allocate buffers on the "node" associated
with the CPU the event is bound to. If it is not bound to a CPU, we
use the current CPU node, using smp_processor_id(). However this is unsafe
in a pre-emptible context and could generate the splats as below :
BUG: using smp_processor_id() in preemptible [00000000] code: perf/2544
caller is tmc_alloc_etf_buffer+0x5c/0x60
CPU: 2 PID: 2544 Comm: perf Not tainted 5.1.0-rc6-147786-g116841e #344
Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno Development Platform, BIOS EDK II Feb 1 2019
Call trace:
dump_backtrace+0x0/0x150
show_stack+0x14/0x20
dump_stack+0x9c/0xc4
debug_smp_processor_id+0x10c/0x110
tmc_alloc_etf_buffer+0x5c/0x60
etm_setup_aux+0x1c4/0x230
rb_alloc_aux+0x1b8/0x2b8
perf_mmap+0x35c/0x478
mmap_region+0x34c/0x4f0
do_mmap+0x2d8/0x418
vm_mmap_pgoff+0xd0/0xf8
ksys_mmap_pgoff+0x88/0xf8
__arm64_sys_mmap+0x28/0x38
el0_svc_handler+0xd8/0x138
el0_svc+0x8/0xc
Use NUMA_NO_NODE hint instead of using the current node for events
not bound to CPUs.
Fixes: 2e499bbc1a ("coresight: tmc: implementing TMC-ETF AUX space API")
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: stable <stable@vger.kernel.org> # 4.7+
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20190620221237.3536-4-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During a perf session we try to allocate buffers on the "node" associated
with the CPU the event is bound to. If it is not bound to a CPU, we
use the current CPU node, using smp_processor_id(). However this is unsafe
in a pre-emptible context and could generate the splats as below :
BUG: using smp_processor_id() in preemptible [00000000] code: perf/1743
caller is tmc_alloc_etr_buffer+0x1bc/0x1f0
CPU: 1 PID: 1743 Comm: perf Not tainted 5.1.0-rc6-147786-g116841e #344
Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno Development Platform, BIOS EDK II Feb 1 2019
Call trace:
dump_backtrace+0x0/0x150
show_stack+0x14/0x20
dump_stack+0x9c/0xc4
debug_smp_processor_id+0x10c/0x110
tmc_alloc_etr_buffer+0x1bc/0x1f0
etm_setup_aux+0x1c4/0x230
rb_alloc_aux+0x1b8/0x2b8
perf_mmap+0x35c/0x478
mmap_region+0x34c/0x4f0
do_mmap+0x2d8/0x418
vm_mmap_pgoff+0xd0/0xf8
ksys_mmap_pgoff+0x88/0xf8
__arm64_sys_mmap+0x28/0x38
el0_svc_handler+0xd8/0x138
el0_svc+0x8/0xc
Use NUMA_NO_NODE hint instead of using the current node for events
not bound to CPUs.
Fixes: 22f429f19c ("coresight: etm-perf: Add support for ETR backend")
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: stable <stable@vger.kernel.org> # 4.20+
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20190620221237.3536-3-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During a perf session we try to allocate buffers on the "node" associated
with the CPU the event is bound to. If it's not bound to a CPU, we use
the current CPU node, using smp_processor_id(). However this is unsafe
in a pre-emptible context and could generate the splats as below :
BUG: using smp_processor_id() in preemptible [00000000] code: perf/1743
caller is alloc_etr_buf.isra.6+0x80/0xa0
CPU: 1 PID: 1743 Comm: perf Not tainted 5.1.0-rc6-147786-g116841e #344
Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno Development Platform, BIOS EDK II Feb 1 2019
Call trace:
dump_backtrace+0x0/0x150
show_stack+0x14/0x20
dump_stack+0x9c/0xc4
debug_smp_processor_id+0x10c/0x110
alloc_etr_buf.isra.6+0x80/0xa0
tmc_alloc_etr_buffer+0x12c/0x1f0
etm_setup_aux+0x1c4/0x230
rb_alloc_aux+0x1b8/0x2b8
perf_mmap+0x35c/0x478
mmap_region+0x34c/0x4f0
do_mmap+0x2d8/0x418
vm_mmap_pgoff+0xd0/0xf8
ksys_mmap_pgoff+0x88/0xf8
__arm64_sys_mmap+0x28/0x38
el0_svc_handler+0xd8/0x138
el0_svc+0x8/0xc
Use NUMA_NO_NODE hint instead of using the current node for events
not bound to CPUs.
Fixes: 855ab61c16 ("coresight: tmc-etr: Refactor function tmc_etr_setup_perf_buf()")
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190620221237.3536-2-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is an arbitrary difference between the prototypes of
bus_find_device() and class_find_device() preventing their callers
from passing the same pair of data and match() arguments to both of
them, which is the const qualifier used in the prototype of
class_find_device(). If that qualifier is also used in the
bus_find_device() prototype, it will be possible to pass the same
match() callback function to both bus_find_device() and
class_find_device(), which will allow some optimizations to be made in
order to avoid code duplication going forward. Also with that, constify
the "data" parameter as it is passed as a const to the match function.
For this reason, change the prototype of bus_find_device() to match
the prototype of class_find_device() and adjust its callers to use the
const qualifier in accordance with the new prototype of it.
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Kershner <david.kershner@unisys.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Harald Freudenberger <freude@linux.ibm.com>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Peter Oberparleiter <oberpar@linux.ibm.com>
Cc: Sebastian Ott <sebott@linux.ibm.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: rafael@kernel.org
Acked-by: Corey Minyard <minyard@acm.org>
Acked-by: David Kershner <david.kershner@unisys.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for the I2C parts
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When neither CONFIG_OF nor CONFIG_ACPI are set, we get a harmless
build warning:
drivers/hwtracing/coresight/coresight-platform.c:26:12: error: unused function 'coresight_alloc_conns'
[-Werror,-Wunused-function]
static int coresight_alloc_conns(struct device *dev,
^
drivers/hwtracing/coresight/coresight-platform.c:46:1: error: unused function 'coresight_find_device_by_fwnode'
[-Werror,-Wunused-function]
coresight_find_device_by_fwnode(struct fwnode_handle *fwnode)
As the code is useless in that configuration anyway, just add
a Kconfig dependency that only allows building when at least
one of the two is set.
This should not hinder compile-testing, as CONFIG_OF can be
enabled on any architecture.
Fixes: 20961aea98 ("coresight: platform: Use fwnode handle for device search")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for platform devices which do not appear on the AMBA
bus.
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for parsing the ACPI platform description
for CoreSight. The connections are encoded in a DSD graph
property with CoreSight specific variation of the property.
The ETMs are listed as the children device of the respective
CPU.
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stimulus base for STM device must be listed as the second memory
resource, followed by the programming base address as described in
"Section 2.3 Resources" in ACPI for CoreSightTM 1.0 Platform Design
documen (DEN0067).
Add support for parsing the information for ACPI.
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So far we have reused the name of the "platform" device for
the CoreSight device. But this is not very intuitive when
we move to ACPI. Also, the ACPI device names have ":" in them
(e.g, ARMHC97C:01), which the perf tool doesn't like very much.
This patch introduces a generic naming scheme, givin more intuitive
names for the devices that appear on the CoreSight bus.
The names follow the pattern "prefix" followed by "index" (e.g, etm5).
We maintain a list of allocated devices per "prefix" to make sure
we don't allocate a new name when it is reprobed (e.g, due to
unsatisifed device dependencies). So, we maintain the list
of "fwnodes" of the parent devices to allocate a consistent name.
All devices except the ETMs get an index allocated in the order
of probing. ETMs get an index based on the CPU they are attached to.
TMC devices are named using "tmc_etf", "tmc_etb", and "tmc_etr"
prefixes depending on the configuration of the device.
The replicators and funnels are not classified as dynamic/static
anymore. One could easily figure that out by checking the presence
of "mgmt" registers under sysfs.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We rely on the device names to find a CoreSight device on the
coresight bus. The device name however is obtained from the platform,
which is bound to the real platform/amba device. As we are about
to use different naming scheme for the coresight devices, we can't
rely on the platform device name to find the corresponding
coresight device. Instead we use the platform agnostic
"fwnode handle" of the parent device to find the devices.
We also reuse the same fwnode as the parent for the Coresight
device we create.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We match of_node while searching for a device. Make this
more generic in preparation for the ACPI support by using
fwnode_handle.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a helper to clean up the platform specific data provided
by the firmware. This will be later used for dropping the necessary
references when we switch to the fwnode handles for tracking
connections.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are about to introduce methods to clean up the platform data
as we switch to tracking the device reference from "name" to "fwnode
handles" for device connections. This requires us to drop the fwnode
handle references when the data is no longer required - i.e, when
the device probe fails or the device gets unregistered.
In order to consolidate the invocation of the cleanup, we delay the
platform probing to the very last minute, possibly before invoking
the coresight_register. Then, we leave the coresight core code to
do the clean up. i.e, if the coresight_register fails, it takes
care of freeing the data. Otherwise, coresight_unregister will
do the necessary operations.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The platform specific information describes the connections and
the ports of a given coresigh device. This information is also
recorded in the coresight device as separate fields. Let us reuse
the original platform description to streamline the handling
of the data.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a device is unregistered, we remove all connection
references to it, by searching the connection records of
all devices in the coresight bus, via coresight_remove_conns.
We could avoid searching if this device doesn't have an input
port (e.g, a source). Also document the purpose of the function.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are about to use a name independent of the parent AMBA device
name. As such, there is no need to have it in the platform description.
Let us move this to coresight description instead.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CPU field is only used by ETMs and there is a separate API
for fetching the same. So, let us use that instead of using
the common platform probing helper. Also, remove it from the
platform_data.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CoreSight components ETM and CPU-Debug are always associated
with CPUs. Replace the of_coresight_get_cpu() with a platform
agnostic helper, in preparation to add ACPI support.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So far we have hard coded the DT platform parsing code in
every driver. Introduce generic helper to parse the information
provided by the firmware in a platform agnostic manner, in preparation
for the ACPI support.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we prepare to add support for ACPI bindings, let us make sure we do
the compatible check only if we are sure we are dealing with a DT based
system.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename the of_coresight_alloc_memory() => coresight_alloc_conns()
as it is independent of the underlying firmware type. This is in
preparation for the ACPI support.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename the firmware handling file to a more generic
name, in preparation for adding ACPI support. Right now
we only support DT and we have all the platform handling
code in of_coresight.c. Let us rename the file to
coresight-platform.c in order to keep the platform handling
in a single place for DT and the upcoming ACPI support.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we are about to refactor the platform specific handling,
make the default buffer size probing generic.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we are about to refactor the platform specific handling
re-arrange some of the DT specific property handling.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we are about to refactor the platform specific handling,
move the DT property handling to generic helpers.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move to using the coresight device name instead of the parent
device name for SINK attribute for PMU.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Track the coresight device instead of the real device.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Track the coresight device instead of the real device.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Keep track of the STM coresight device which is a child device
of the AMBA device. Since we can get to the coresight_device
from the "device" instance, remove the explicit field.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to using the coresight device instead of the parent
amba device.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to using the CoreSight device instead of the real
amba device.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to use a consistent device naming scheme,
clean up the device link tracking in replicator driver.
Use the "coresight" device instead of the "real" parent device
for all internal purposes. All other requests (e.g, power management,
DMA operations) must use the "real" device which is the parent device.
Since the CATU driver also uses the TMC-SG infrastructure, update
the callers to ensure they pass the appropriate device argument
for the tables.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to use a consistent device naming scheme,
clean up the device link tracking in replicator driver.
Use the "coresight" device instead of the "real" parent device
for all internal purposes. All other requests (e.g, power management,
DMA operations) must use the "real" device which is the parent device.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to use a consistent device naming scheme,
clean up the device link tracking in funnel driver.
Use the "coresight" device instead of the "real" parent device
for all internal purposes. All other requests (e.g, power management,
DMA operations) must use the "real" device which is the parent device.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch avoids setting the truncated flag when operating in snapshot
mode since the trace buffer is expected to be truncated and discontinuous
from one snapshot to another. Moreover when the truncated flag is set
the perf core stops enabling the event, waiting for user space to consume
the data. In snapshot mode this is clearly not what we want since it
results in stale data.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When working in snapshot mode function perf_aux_output_begin()
does not set the handle->size because the size is expected to be
deduced by the placement of the "head" and "old" pointers in user
space. As such there is no point in trying to adjust the amount
of data to copy to the ring buffer.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unify amongst sink drivers how the AUX ring buffer head is communicated
to user space. That way the same algorithm in user space can be used to
determine where the latest data is and how much of it to access.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unify amongst sink drivers how the AUX ring buffer head is communicated
to user space. That way the same algorithm in user space can be used to
determine where the latest data is and how much of it to access.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unify amongst sink drivers how the AUX ring buffer head is communicated
to user space. That way the same algorithm in user space can be used to
determine where the latest data is and how much of it to access.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since CoreSight hardware topology can use a 'hidden' funnel in the
trace data path, this kind funnel doesn't have register for accessing
and is used by default from hardware design perspective. Below is an
example for related hardware topology:
+------+ +------+
| cpu0 |->| ETM |-\
+------+ +------+ \-> +--------+ +-----+
...... | Funnel |->| ETF |-\ Hidden funnel
+------+ +------+ /-> +--------+ +-----+ \ |
| cpu3 |->| ETM |-/ \ V
+------+ +------+ \-> +--------+
| Funnel |-> ...
+------+ +------+ /-> +--------+
| cpu4 |->| ETM |-\ /
+------+ +------+ \-> +--------+ +-----+ /
...... | Funnel |->| ETF |-/
+------+ +------+ /-> +--------+ +-----+
| cpu7 |->| ETM |-/
+------+ +------+
The CoreSight funnel driver only supports dynamic funnel with
registration register resource, thus it cannot support for the static
funnel case and it's impossible to create trace data path for this case.
This patch is to extend CoreSight funnel driver to support both for
static funnel and dynamic funnel. For the dynamic funnel it reuses the
code existed in the driver, for static funnel the driver will support
device probe if without providing register resource and the driver skips
registers accessing when detect the register base is NULL.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Wanglai Shi <shiwanglai@hisilicon.com>
Suggested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a device id for the new static replicator compatible
string; it changes the driver name from "coresight-replicator" to
"coresight-static-replicator" as well.
This patch also gives warning when use the replicator obsolete DT
binding.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for CPU-wide trace scenarios by making sure that
only the sources monitoring the same process have access to a common sink.
Because the sink is shared between sources, the first source to use the
sink switches it on while the last one does the cleanup. Any attempt to
modify the HW is overlooked for as long as more than one source is using
a sink.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for CPU-wide trace scenarios by making sure that
only the sources monitoring the same process have access to a common sink.
Because the sink is shared between sources, the first source to use the
sink switches it on while the last one does the cleanup. Any attempt to
modify the HW is overlooked for as long as more than one source is using
a sink.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for CPU-wide trace scenarios by making sure that
only the sources monitoring the same process have access to a common sink.
Because the sink is shared between sources, the first source to use the
sink switches it on while the last one does the cleanup. Any attempt to
modify the HW is overlooked for as long as more than one source is using
a sink.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch uses the PID of the process being traced to allocate and free
ETR memory buffers for CPU-wide scenarios. The implementation is tailored
to handle both N:1 and 1:1 source/sink HW topologies.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In CPU-wide scenarios with an N:1 source/sink topology, sources share
the same sink. In order to reuse the same sink for all sources an
IDR is needed to archive events that have already been accounted for.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds reference counting to struct etr_buf so that, in CPU-wide
trace scenarios, shared buffers can be disposed of when no longer used.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to support CPU-wide trace scenarios, introduce the notion
of process ID to ETR devices. That way events monitoring the same process
can use the same etr_buf, allowing multiple CPUs to use the same sink.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Buffer allocation is different when dealing with per-thread and
CPU-wide sessions. In preparation to support CPU-wide trace scenarios
simplify things by keeping allocation functions for both type separate.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactoring function tmc_etr_setup_perf_buf() so that it only deals
with the high level etr_perf_buffer, leaving the allocation of the
backend buffer (i.e etr_buf) to another function.
That way the backend buffer allocation function can decide if it wants
to reuse an existing buffer (CPU-wide trace scenarios) or simply create
a new one.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make struct perf_event available to sink buffer allocation functions in
order to use the pid they carry to allocate and free buffer memory along
with regimenting access to what source a sink can collect data for.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function free_event_data() is already busy and is bound to become
worse with the addition of CPU-wide trace scenarios. As such spin
off a new function to strickly take care of the sink buffers.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no point in allocating sink memory for a trace session if
there is not a way to free it once it is no longer needed. As such make
sure the sink API function to allocate and free memory have been
implemented before moving ahead with the establishment of a trace
session.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When operating in CPU-wide trace scenarios and working with an N:1
source/sink HW topology, update() functions need to be made atomic
in order to avoid racing with start and stop operations.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When disabling a sink the reference counter ensures the operation goes
through if nobody else is using it. As such if drvdata::mode is already
set do CS_MODE_DISABLED, it is an error and should be reported as such.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When operating in CPU-wide mode with an N:1 source/sink HW topology,
multiple CPUs can access a sink concurrently. As such reference counting
needs to happen when the device's spinlock is held to avoid racing with
other operations (start(), update(), stop()), such as:
session A Session B
----- -------
enable_sink
atomic_inc(refcount) = 1
...
atomic_dec(refcount) = 0 enable_sink
if (refcount == 0) disable_sink
atomic_inc()
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to handle device reference counting inside of the sink
drivers, add a return code to the sink::disable() operation so that
proper action can be taken if a sink has not been disabled.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Configure timestamps to be emitted at regular intervals in the trace
stream to temporally correlate instructions executed on different CPUs.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Resource selector pair 0 is always implemented and reserved. As such
it should not be explicitly programmed.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the proper bit in the configuration register when contextID tracing
has been requested by user space. That way PE_CONTEXT elements are
generated by the tracers when a process is installed on a CPU.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add to the capabilities the ITRACE property so that ITRACE START events
are generated when the PMU is switched on by the core.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the power only if we were successful in probing the device.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the power handle only if we were successful. Otherwise
the AMBA bus code would do the rest.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the power only when we have successfully probed. Otherwise
leave it to the amba probe to do the rest.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[Removed extra newline left after original modification]
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We drop the power before we complete the probe successfully. We
are supposed to drop it only when we are successful. Also, probing
the etb_buffer_length happens with the power turned up. So we don't
need to do that again in the helper.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With commit c2c729415b ("coresight: platform: Cleanup coresight
connection handling"), we switched to re-using coresight_connections
for the coresight_device. However, that introduced a mismatch in the
alloc/free of the connections. The allocation is made using devm_*,
while we use kfree() to release the memory when a device is released
(even though we don't support this at the moment). Fix this by leaving
it to the automatic freeing of the memory.
Fixes: c2c729415b ("coresight: platform: Cleanup coresight connection handling")
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge the drivers for the two varieties of replicators into
a singel one. The dynamic replicator has programming base
which can be programmed to filter the trace data. The driver
detects the type based on the "base" address value of the
device, which is NULL for the static device.
Also, while at it, remove the now obsolete DYNAMIC_REPLICATOR
config entry.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename the dynamic replicator specific routines for merging with the
replicator driver. Also re-arrange the probe routine to make it easier
to merge.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As a preparatory step to merge the separate drivers for static and
dynamic replicators, annotate the static replicator specific details.
Also refactor the probe routine to make it generic in order to merge
the drivers easily.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We fail to disable the clock in case of a failure during the
probe. Clean this up. Also, we are supposed to drop the pm reference
only when the probing is successful.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we failed to setup the DMA mask for TMC-ETR, report the
error before failing the probe.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix sparse warnings:
drivers/hwtracing/coresight/coresight-catu.c:488:35: warning:
symbol 'catu_helper_ops' was not declared. Should it be static?
drivers/hwtracing/coresight/coresight-catu.c:493:28: warning:
symbol 'catu_ops' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang points out a syntax error, as the etr_catu_buf_ops structure is
declared 'static' before the type is known:
In file included from drivers/hwtracing/coresight/coresight-tmc-etr.c:12:
drivers/hwtracing/coresight/coresight-catu.h:116:40: warning: tentative definition of variable with internal linkage has incomplete non-array type 'const struct etr_buf_operations' [-Wtentative-definition-incomplete-type]
static const struct etr_buf_operations etr_catu_buf_ops;
^
drivers/hwtracing/coresight/coresight-catu.h:116:21: note: forward declaration of 'struct etr_buf_operations'
static const struct etr_buf_operations etr_catu_buf_ops;
This seems worth fixing in the code, so replace pointer to the empty
constant structure with a NULL pointer. We need an extra NULL pointer
check here, but the result should be better object code otherwise,
avoiding the silly empty structure.
Fixes: 434d611cdd ("coresight: catu: Plug in CATU as a backend for ETR buffer")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[Fixed line over 80 characters]
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- An improvement from Ard Biesheuvel, who noted that the identity map
setup was taking a long time due to flush_cache_louis().
- Update a comment about dma_ops from Wolfram Sang.
- Remove use of "-p" with ld, where this flag has been a no-op since
2004.
- Remove the printing of the virtual memory layout, which is no longer
useful since we hide pointers.
- Correct SCU help text.
- Remove legacy TWD registration method.
- Add pgprot_device() implementation for mapping PCI sysfs resource
files.
- Initialise PFN limits earlier for kmemleak.
- Fix argument count to match macro definition (affects clang builds)
- Use unified assembler language almost everywhere for clang, and
other clang improvements (from Stefan Agner, Nathan Chancellor).
- Support security extension for noMMU and other noMMU cleanups
(from Vladimir Murzin).
- Remove unnecessary SMP bringup code (which was incorrectly copy'n'
pasted from the ARM platform implementations) and remove it from
the arch code to discourge further copys of it appearing.
- Add Cortex A9 erratum preventing kexec working on some SoCs.
- AMBA bus identification updates from Mike Leach.
- More use of raw spinlocks to avoid -RT kernel issues
(from Yang Shi and Sebastian Andrzej Siewior).
- MCPM hyp/svc mode mismatch fixes from Marek Szyprowski.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=U6og
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
- An improvement from Ard Biesheuvel, who noted that the identity map
setup was taking a long time due to flush_cache_louis().
- Update a comment about dma_ops from Wolfram Sang.
- Remove use of "-p" with ld, where this flag has been a no-op since
2004.
- Remove the printing of the virtual memory layout, which is no longer
useful since we hide pointers.
- Correct SCU help text.
- Remove legacy TWD registration method.
- Add pgprot_device() implementation for mapping PCI sysfs resource
files.
- Initialise PFN limits earlier for kmemleak.
- Fix argument count to match macro definition (affects clang builds)
- Use unified assembler language almost everywhere for clang, and other
clang improvements (from Stefan Agner, Nathan Chancellor).
- Support security extension for noMMU and other noMMU cleanups (from
Vladimir Murzin).
- Remove unnecessary SMP bringup code (which was incorrectly copy'n'
pasted from the ARM platform implementations) and remove it from the
arch code to discourge further copys of it appearing.
- Add Cortex A9 erratum preventing kexec working on some SoCs.
- AMBA bus identification updates from Mike Leach.
- More use of raw spinlocks to avoid -RT kernel issues (from Yang Shi
and Sebastian Andrzej Siewior).
- MCPM hyp/svc mode mismatch fixes from Marek Szyprowski.
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (32 commits)
ARM: 8849/1: NOMMU: Fix encodings for PMSAv8's PRBAR4/PRLAR4
ARM: 8848/1: virt: Align GIC version check with arm64 counterpart
ARM: 8847/1: pm: fix HYP/SVC mode mismatch when MCPM is used
ARM: 8845/1: use unified assembler in c files
ARM: 8844/1: use unified assembler in assembly files
ARM: 8843/1: use unified assembler in headers
ARM: 8841/1: use unified assembler in macros
ARM: 8840/1: use a raw_spinlock_t in unwind
ARM: 8839/1: kprobe: make patch_lock a raw_spinlock_t
ARM: 8837/1: coresight: etmv4: Update ID register table to add UCI support
ARM: 8836/1: drivers: amba: Update component matching to use the CoreSight UCI values.
ARM: 8838/1: drivers: amba: Updates to component identification for driver matching.
ARM: 8833/1: Ensure that NEON code always compiles with Clang
ARM: avoid Cortex-A9 livelock on tight dmb loops
ARM: smp: remove arch-provided "pen_release"
ARM: actions: remove boot_lock and pen_release
ARM: oxnas: remove CPU hotplug implementation
ARM: qcom: remove unnecessary boot_lock
ARM: 8832/1: NOMMU: Limit visibility for CONFIG_FLASH_{MEM_BASE,SIZE}
ARM: 8831/1: NOMMU: pmsa-v8: remove unneeded semicolon
...
Here is the big char/misc driver patch pull request for 5.1-rc1.
The largest thing by far is the new habanalabs driver for their AI
accelerator chip. For now it is in the drivers/misc directory but will
probably move to a new directory soon along with other drivers of this
type.
Other than that, just the usual set of individual driver updates and
fixes. There's an "odd" merge in here from the DRM tree that they asked
me to do as the MEI driver is starting to interact with the i915 driver,
and it needed some coordination. All of those patches have been
properly acked by the relevant subsystem maintainers.
All of these have been in linux-next with no reported issues, most for
quite some time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXH+dPQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym1fACgvpZAxjNzoRQJ6f06tc8ujtPk9rUAnR+tCtrZ
9e3l7H76oe33o96Qjhor
=8A2k
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver patch pull request for 5.1-rc1.
The largest thing by far is the new habanalabs driver for their AI
accelerator chip. For now it is in the drivers/misc directory but will
probably move to a new directory soon along with other drivers of this
type.
Other than that, just the usual set of individual driver updates and
fixes. There's an "odd" merge in here from the DRM tree that they
asked me to do as the MEI driver is starting to interact with the i915
driver, and it needed some coordination. All of those patches have
been properly acked by the relevant subsystem maintainers.
All of these have been in linux-next with no reported issues, most for
quite some time"
* tag 'char-misc-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (219 commits)
habanalabs: adjust Kconfig to fix build errors
habanalabs: use %px instead of %p in error print
habanalabs: use do_div for 64-bit divisions
intel_th: gth: Fix an off-by-one in output unassigning
habanalabs: fix little-endian<->cpu conversion warnings
habanalabs: use NULL to initialize array of pointers
habanalabs: fix little-endian<->cpu conversion warnings
habanalabs: soft-reset device if context-switch fails
habanalabs: print pointer using %p
habanalabs: fix memory leak with CBs with unaligned size
habanalabs: return correct error code on MMU mapping failure
habanalabs: add comments in uapi/misc/habanalabs.h
habanalabs: extend QMAN0 job timeout
habanalabs: set DMA0 completion to SOB 1007
habanalabs: fix validation of WREG32 to DMA completion
habanalabs: fix mmu cache registers init
habanalabs: disable CPU access on timeouts
habanalabs: add MMU DRAM default page mapping
habanalabs: Dissociate RAZWI info from event types
misc/habanalabs: adjust Kconfig to fix build errors
...
SDM845 has ETMv4.2 and can use the existing etm4x driver.
But the current etm driver checks only for ETMv4.0 and
errors out for other etm4x versions. This patch adds this
missing support to enable SoC's with ETMv4x to use same
driver by checking only the ETM architecture major version
number.
Without this change, we get below error during etm probe:
/ # dmesg | grep etm
[ 6.660093] coresight-etm4x: probe of 7040000.etm failed with error -22
[ 6.666902] coresight-etm4x: probe of 7140000.etm failed with error -22
[ 6.673708] coresight-etm4x: probe of 7240000.etm failed with error -22
[ 6.680511] coresight-etm4x: probe of 7340000.etm failed with error -22
[ 6.687313] coresight-etm4x: probe of 7440000.etm failed with error -22
[ 6.694113] coresight-etm4x: probe of 7540000.etm failed with error -22
[ 6.700914] coresight-etm4x: probe of 7640000.etm failed with error -22
[ 6.707717] coresight-etm4x: probe of 7740000.etm failed with error -22
With this change, etm probe is successful:
/ # dmesg | grep etm
[ 6.659198] coresight-etm4x 7040000.etm: CPU0: ETM v4.2 initialized
[ 6.665848] coresight-etm4x 7140000.etm: CPU1: ETM v4.2 initialized
[ 6.672493] coresight-etm4x 7240000.etm: CPU2: ETM v4.2 initialized
[ 6.679129] coresight-etm4x 7340000.etm: CPU3: ETM v4.2 initialized
[ 6.685770] coresight-etm4x 7440000.etm: CPU4: ETM v4.2 initialized
[ 6.692403] coresight-etm4x 7540000.etm: CPU5: ETM v4.2 initialized
[ 6.699024] coresight-etm4x 7640000.etm: CPU6: ETM v4.2 initialized
[ 6.705646] coresight-etm4x 7740000.etm: CPU7: ETM v4.2 initialized
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds macro to enable UCI entries to be added to AMBA ID tables.
Updates the ID register tables to contain a UCI entry for the A35 ETM
device to allow correct matching of driver in the amba bus code.
Signed-off-by: Mike Leach <mike.leach@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The CoreSight specification (ARM IHI 0029E), updates the ID register
requirements for components on an AMBA bus, to cover both traditional
ARM Primecell type devices, and newer CoreSight and other components.
The Peripheral ID (PID) / Component ID (CID) pair is extended in certain
cases to uniquely identify components. CoreSight components related to
a single function can share Peripheral ID values, and must be further
identified using a Unique Component Identifier (UCI). e.g. the ETM, CTI,
PMU and Debug hardware of the A35 all share the same PID.
Bits 15:12 of the CID are defined to be the device class.
Class 0xF remains for PrimeCell and legacy components.
Class 0x9 defines the component as CoreSight (CORESIGHT_CID above)
Class 0x0, 0x1, 0xB, 0xE define components that do not have driver support
at present.
Class 0x2-0x8,0xA and 0xD-0xD are presently reserved.
The specification futher defines which classes of device use the standard
CID/PID pair, and when additional ID registers are required.
This patch introduces the amba_cs_uci_id structure which will be used in
all coresight drivers for indentification via the private data pointer in
the amba_id structure.
Existing drivers that currently use the amba_id->data pointer for private
data are updated to use the amba_cs_uci_id->data pointer. Macros and
inline functions are added to simplify this code.
Signed-off-by: Mike Leach <mike.leach@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Currently, the address range calculation for file-based filters works as
long as the vma that maps the matching part of the object file starts
from offset zero into the file (vm_pgoff==0). Otherwise, the resulting
filter range would be off by vm_pgoff pages. Another related problem is
that in case of a partially matching vma, that is, a vma that matches
part of a filter region, the filter range size wouldn't be adjusted.
Fix the arithmetics around address filter range calculations, taking
into account vma offset, so that the entire calculation is done before
the filter configuration is passed to the PMU drivers instead of having
those drivers do the final bit of arithmetics.
Based on the patch by Adrian Hunter <adrian.hunter.intel.com>.
Reported-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Fixes: 375637bc52 ("perf/core: Introduce address range filtering")
Link: http://lkml.kernel.org/r/20190215115655.63469-3-alexander.shishkin@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This patch uses the information conveyed by perf_event::attr::config2
to select a sink to use for the session. That way a sink can easily be
selected to be used by more than one source, something that isn't currently
possible with the sysfs implementation.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a "sinks" directory entry so that users can see all the sinks
available in the system in a single place. Individual sink are added
as they are registered with the coresight bus.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When pmu::setup_aux() is called the coresight PMU needs to know which
sink to use for the session by looking up the information in the
event's attr::config2 field.
As such simply replace the cpu information by the complete perf_event
structure and change all affected customers.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/hwtracing/coresight/coresight-stm.c: In function 'stm_probe':
drivers/hwtracing/coresight/coresight-stm.c:796:9: warning:
variable 'res_size' set but not used [-Wunused-but-set-variable]
It never used since introduction in commit 237483aa5c ("coresight: stm:
adding driver for CoreSight STM component")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to add the AMBA device ID for CA73 CPU, so that CPU debug
module can be initialized successfully when a SoC contain CA73 CPUs.
This patch has been verified on 96boards Hikey960.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch uses the information conveyed by perf_event::attr::config2
to select a sink to use for the session. That way a sink can easily be
selected to be used by more than one source, something that isn't currently
possible with the sysfs implementation.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-s390@vger.kernel.org
Link: http://lkml.kernel.org/r/20190131184714.20388-4-mathieu.poirier@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add a "sinks" directory entry so that users can see all the sinks
available in the system in a single place. Individual sink are added
as they are registered with the coresight bus.
Committer tests:
Test built on a ubuntu 18.04 container with a cross build environment to
arm64, the new field is there, need to find a machine with this feature
to do further testing in the future.
root@d15263e5734a:/git/perf# grep CORESIGHT /tmp/build/v5.0-rc2+/.config
CONFIG_CORESIGHT=y
CONFIG_CORESIGHT_LINKS_AND_SINKS=y
CONFIG_CORESIGHT_LINK_AND_SINK_TMC=y
CONFIG_CORESIGHT_CATU=y
CONFIG_CORESIGHT_SINK_TPIU=y
CONFIG_CORESIGHT_SINK_ETBV10=y
CONFIG_CORESIGHT_SOURCE_ETM4X=y
CONFIG_CORESIGHT_DYNAMIC_REPLICATOR=y
CONFIG_CORESIGHT_STM=y
CONFIG_CORESIGHT_CPU_DEBUG=m
root@d15263e5734a:/git/perf#
root@d15263e5734a:/git/perf# file /tmp/build/v5.0-rc2+/drivers/hwtracing/coresight/*.o
.../coresight/coresight-catu.o: ELF 64-bit MSB relocatable, ARM aarch64, version 1 (SYSV), not stripped
.../coresight/coresight-cpu-debug.mod.o: ELF 64-bit MSB relocatable, ARM aarch64, version 1 (SYSV), not stripped
.../coresight/coresight-cpu-debug.o: ELF 64-bit MSB relocatable, ARM aarch64, version 1 (SYSV), not stripped
.../coresight/coresight-dynamic-replicator.o: ELF 64-bit MSB relocatable, ARM aarch64, version 1 (SYSV), not stripped
.../coresight/coresight-etb10.o: ELF 64-bit MSB relocatable, ARM aarch64, version 1 (SYSV), not stripped
.../coresight/coresight-etm-perf.o: ELF 64-bit MSB relocatable, ARM aarch64, version 1 (SYSV), not stripped
.../coresight/coresight-etm4x-sysfs.o: ELF 64-bit MSB relocatable, ARM aarch64, version 1 (SYSV), not stripped
.../coresight/coresight-etm4x.o: ELF 64-bit MSB relocatable, ARM aarch64, version 1 (SYSV), not stripped
.../coresight/coresight-funnel.o: ELF 64-bit MSB relocatable, ARM aarch64, version 1 (SYSV), not stripped
.../coresight/coresight-replicator.o: ELF 64-bit MSB relocatable, ARM aarch64, version 1 (SYSV), not stripped
.../coresight/coresight-stm.o: ELF 64-bit MSB relocatable, ARM aarch64, version 1 (SYSV), not stripped
.../coresight/coresight-tmc-etf.o: ELF 64-bit MSB relocatable, ARM aarch64, version 1 (SYSV), not stripped
.../coresight/coresight-tmc-etr.o: ELF 64-bit MSB relocatable, ARM aarch64, version 1 (SYSV), not stripped
.../coresight/coresight-tmc.o: ELF 64-bit MSB relocatable, ARM aarch64, version 1 (SYSV), not stripped
.../coresight/coresight-tpiu.o: ELF 64-bit MSB relocatable, ARM aarch64, version 1 (SYSV), not stripped
.../coresight/coresight.o: ELF 64-bit MSB relocatable, ARM aarch64, version 1 (SYSV), not stripped
.../coresight/of_coresight.o: ELF 64-bit MSB relocatable, ARM aarch64, version 1 (SYSV), not stripped
root@d15263e5734a:/git/perf#
root@d15263e5734a:/git/perf# pahole -C coresight_device /tmp/build/v5.0-rc2+/drivers/hwtracing/coresight/coresight.o
struct coresight_device {
struct coresight_connection * conns; /* 0 8 */
int nr_inport; /* 8 4 */
int nr_outport; /* 12 4 */
enum coresight_dev_type type; /* 16 4 */
union coresight_dev_subtype subtype; /* 20 8 */
/* XXX 4 bytes hole, try to pack */
const struct coresight_ops * ops; /* 32 8 */
struct device dev; /* 40 1408 */
/* XXX last struct has 7 bytes of padding */
/* --- cacheline 22 boundary (1408 bytes) was 40 bytes ago --- */
atomic_t * refcnt; /* 1448 8 */
bool orphan; /* 1456 1 */
bool enable; /* 1457 1 */
bool activated; /* 1458 1 */
/* XXX 5 bytes hole, try to pack */
struct dev_ext_attribute * ea; /* 1464 8 */
/* size: 1472, cachelines: 23, members: 12 */
/* sum members: 1463, holes: 2, sum holes: 9 */
/* paddings: 1, sum paddings: 7 */
};
root@d15263e5734a:/git/perf#
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-s390@vger.kernel.org
Link: http://lkml.kernel.org/r/20190131184714.20388-3-mathieu.poirier@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When pmu::setup_aux() is called the coresight PMU needs to know which
sink to use for the session by looking up the information in the
event's attr::config2 field.
As such simply replace the cpu information by the complete perf_event
structure and change all affected customers.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki Poulouse <suzuki.poulose@arm.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-s390@vger.kernel.org
Link: http://lkml.kernel.org/r/20190131184714.20388-2-mathieu.poirier@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
There is a spelling mistake in the dev_info error message, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch deals with the release of the CLAIM tag when the ETM is
operated from perf. Otherwise the tag is left asserted and subsequent
requests to use the device fail.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch moves access to the CLAIM tag so that no modification to the HW
happens before and after the CLAIM operation has been carried.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch rectifies the sequence of events in function
tmc_etb_disable_hw() by disabling the HW first and then releasing the
CLAIM tag. Otherwise we could be corrupting the configuration done by an
external agent that would have claimed the device after we have released
it.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Following in the footstep of what was done for other CoreSight devices,
add CLAIM tag support to ETB10 in order to synchronise access to the
HW between the kernel and an external agent.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use CLAIM tags to make sure the device is available for use.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_node_put and put_device has taken the null pointer check into account.
So it is safe to remove the duplicated check.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use CLAIM protocol to make sure the device is available for use.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the CLAIM protocol to grab the ownership of the component when
in use.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the CLAIM protocol to grab the ownership of the component.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the CLAIM tags to grab the device for self-hosted usage.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coresight architecture defines CLAIM tags for a device to negotiate
control of the components (external agent vs self-hosted). Each device
has a pair of registers (CLAIMSET & CLAIMCLR) for managing the CLAIM
tags. However, the protocol for the CLAIM tags is IMPLEMENTATION DEFINED.
PSCI has recommendations for the use of the CLAIM tags to negotiate
controls for external agent vs self-hosted use. This patch implements
the recommended protocol by PSCI.
The claim/disclaim operations are performed from the device specific
drivers. The disadvantage is that the calls are sprinkled in each driver,
but this makes the operation much simpler.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a replicator port is enabled, we block the traffic
on the other port and route all traffic to the new enabled
port. If there are two active trace sessions each targeting
the two different paths from the replicator, the second session
will disable the first session and route all the data to the
second path.
ETR
/
e.g, replicator
\
ETB
If CPU0 is operated in sysfs mode to ETR and CPU1 is operated
in perf mode to ETB, depending on the order in which the
replicator is enabled one device is blocked.
Ideally we need trace-id for the session to make the
right choice. That implies we need a trace-id allocation
logic for the coresight subsystem and use that to route
the traffic. The short term solution is to only manage
the "target port" and leave the other port untouched.
That leaves both the paths unaffected, except that some
unwanted traffic may be pushed to the paths (if the Trace-IDs
are not far enough), which is still fine and can be filtered
out while processing rather than silently blocking the data.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for reporting errors back from the SMP cross
function call for enabling ETM.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for handling errors in enabling the component.
The ETM is enabled via cross call to owner CPU. Make
necessary changes to report the error back from the cross
call.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare to handle errors in enabling the hardware and
report it back to the core driver.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure we honor the errors in CATU device and abort the operation.
While at it, delay setting the etr_buf for the session until we are
sure that we are indeed enabling the ETR.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor the tmc-etr enable operation to make it easier to
handle errors in enabling the hardware. We need to make
sure that the buffer is compatible with the ETR. This
patch re-arranges to make the error handling easier, by
deferring the hardware enablement until all the errors
are checked. This also avoids turning the CATU on/off
during a sysfs read session.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
coresight_enable_path() enables the components in a trace
path from a given source to a sink, excluding the source.
The operation is performed in the reverse order; the sink
first and then backwards in the list. However, if we encounter
an error in enabling any of the component, we simply disable
all the components in the given path irrespective of whether
we enabled some of the components in the enable iteration.
This could interfere with another trace session if one of the
link devices is turned off (e.g, TMC-ETF). So, we need to
make sure that we only disable those components which were
actually enabled from the iteration.
This patch achieves the same by refactoring the coresight_disable_path
to accept a "node" to start from in the forward order, which can
then be used from the error path of coresight_enable_path().
With this change, we don't issue a disable call back for a component
which didn't get enabled. This change of behavior triggers
a bug in coresight_enable_link(), where we leave the refcount
on the device and will prevent the device from being enabled
forever. So, we also drop the refcount in the coresight_enable_link()
if the operation failed.
Also, with the refactoring, we always start after the first node (which
is the "SOURCE" device) for disabling the entire path. This implies,
we must not find a "SOURCE" in the middle of the path. Hence, added
a WARN_ON() to make sure the paths we get are sane, rather than
simply ignoring them.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
>From the comment in the code, it claims the requirement for byte-address
alignment for RRP register: 'for 32-bit, 64-bit and 128-bit wide trace
memory, the four LSBs must be 0s. For 256-bit wide trace memory, the
five LSBs must be 0s'. This isn't consistent with the program, the
program sets five LSBs as zeros for 32/64/128-bit wide trace memory and
set six LSBs zeros for 256-bit wide trace memory.
After checking with the CoreSight Trace Memory Controller technical
reference manual (ARM DDI 0461B, section 3.3.4 RAM Read Pointer
Register), it proves the comment is right and the program does wrong
setting.
This patch fixes byte-address alignment for RRP by following correct
definition in the technical reference manual.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ETB dump function tmc_etb_dump_hw() it has nested loops. The second
level loop is to iterate index in the range [0 .. drvdata->memwidth);
but the index isn't really used in the code, thus the second level
loop is useless.
This patch is to remove the second level loop; the refactor also reduces
indentation and we can use 'break' to replace 'goto' tag.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For non-VHE systems host kernel runs at EL1 and jumps to EL2 whenever
hypervisor code should be executed. In this case ETM4x driver must
restrict configuration to EL1 when it setups kernel tracing.
However, there is no separate hypervisor privilege level when VHE
is enabled, the host kernel runs at EL2.
This patch fixes configuration of TRCACATRn register for VHE systems
so that ETM_EXLEVEL_NS_HYP bit is used instead of ETM_EXLEVEL_NS_OS
to on/off kernel tracing. At the same time, it moves common code
to new helper.
Signed-off-by: Tomasz Nowicki <tnowicki@caviumnetworks.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Up until now the relative simplicity of enabling the ETB made it
possible to accommodate processing for both sysFS and perf methods.
But work on claimtags and CPU-wide trace scenarios is adding some
complexity, making the current code messy and hard to maintain.
As such follow what has been done for ETF and ETR components and split
function etb_enable() so that processing for both API can be done
cleanly.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch moves the etb_drvdata::mode from a locat_t to a simple u32,
as it is for the ETF and ETR drivers. This streamlines the code and adds
commonality with the other drivers when dealing with similar operations.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for using TMC-ETR as backend for ETM perf tracing.
We use software double buffering at the moment. i.e, the TMC-ETR
uses a separate buffer than the perf ring buffer. The data is
copied to the perf ring buffer once a session completes.
The TMC-ETR would try to match the larger of perf ring buffer
or the ETR buffer size configured via sysfs, scaling down to
a minimum limit of 1MB.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In coresight perf mode, we need to prepare the sink before
starting a session, which is done via set_buffer call back.
We then proceed to enable the tracing. If we fail to start
the session successfully, we leave the sink configuration
unchanged. In order to make the operation atomic and to
avoid yet another call back to clear the buffer, we get
rid of the "set_buffer" call back and pass the buffer details
via enable() call back to the sink.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can always find the sink configuration for a given perf_output_handle.
Add a helper to retrieve the sink configuration for a given
perf_output_handle. This will be used to get rid of the set_buffer()
call back.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now we issue an update_buffer() and reset_buffer() call backs
in succession when we stop tracing an event. The update_buffer is
supposed to check the status of the buffer and make sure the ring buffer
is updated with the trace data. And we store information about the
size of the data collected only to be consumed by the reset_buffer
callback which always follows the update_buffer. This was originally
designed for handling future IPs which could trigger a buffer overflow
interrupt. This patch gets rid of the reset_buffer callback altogether
and performs the actions in update_buffer, making it return the size
collected. We can always add the support for handling the overflow
interrupt case later.
This removes some not-so pretty hack (storing the new head in the
size field for snapshot mode) and cleans it up a little bit.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert component enable/disable messages from dev_info to dev_dbg.
When used with perf, the components in the paths are enabled/disabled
during each schedule of the run, which can flood the dmesg with these
messages. Moreover, they are only useful for debug purposes. So,
convert such messages to dev_dbg() which can be turned on as
needed.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the ETR now uses mode specific buffers, we can reliably
provide the trace data captured in sysfs mode, even when the ETR
is operating in PERF mode.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the ETR could be driven either by SYSFS or by perf, it
becomes complicated how we deal with the buffers used for each
of these modes. The ETR driver cannot simply free the current
attached buffer without knowing the provider (i.e, sysfs vs perf).
To solve this issue, we provide:
1) the driver-mode specific etr buffer to be retained in the drvdata
2) the etr_buf for a session should be passed on when enabling the
hardware, which will be stored in drvdata->etr_buf. This will be
replaced (not free'd) as soon as the hardware is disabled, after
necessary sync operation.
The advantages of this are :
1) The common code path doesn't need to worry about how to dispose
an existing buffer, if it is about to start a new session with a
different buffer, possibly in a different mode.
2) The driver mode can control its buffers and can get access to the
saved session even when the hardware is operating in a different
mode. (e.g, we can still access a trace buffer from a sysfs mode
even if the etr is now used in perf mode, without disrupting the
current session.)
Towards this, we introduce a sysfs specific data which will hold the
etr_buf used for sysfs mode of operation, controlled solely by the
sysfs mode handling code.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We enable the trace path, before activating the source.
If we fail to enable the source, we must disable the path
to make sure it is available for another session.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the moment, if there is no CPU specified for a given
event, we use cpu_online_mask and try to build path for
each of the CPUs in the mask. This could prevent any CPU
that is turned online later to be used for the tracing.
This patch changes to use the cpu_present_mask and tries
to build path for as much CPUs as possible ignoring the
failures in building path for some of the CPUs. If ever
we try to trace on those CPUs, we fail the operation.
Based on a patch from Mathieu Poirier.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We create a coresight trace path for each online CPU when
we start the event. We rely on the number of online CPUs
and then go on to allocate an array matching the "number of
online CPUs" for holding the path and then uses normal
CPU id as the index to the array. This is problematic as
we could have some offline CPUs causing us to access beyond
the actual array size (e.g, on a dual SMP system, if CPU0 is
offline, CPU1 could be really accessing beyond the array).
The solution is to switch to per-cpu array for holding the path.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the ETB is already enabled in sysfs mode, the ETB reports
success even if a perf mode is requested. Fix this by checking
the requested mode.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The coresight components could be operated either in sysfs mode or in perf
mode. For some of the components, the mode of operation doesn't matter as
they simply relay the data to the next component in the trace path. But for
sinks, they need to be able to provide the trace data back to the user.
Thus we need to make sure that "mode" is handled appropriately. e.g,
the sysfs mode could have multiple sources driving the trace data, while
perf mode doesn't allow sharing the sink.
The coresight_enable_sink() however doesn't really allow this check to
trigger as it skips the "enable_sink" callback if the component is
already enabled, irrespective of the mode. This could cause mixing
of data from different modes or even same mode (in perf), if the
sources are different. Also, if we fail to enable the sink while
enabling a path (where sink is the first component enabled),
we could end up in disabling the components in the "entire"
path which were not enabled in this trial, causing disruptions
in the existing trace paths.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use ERR_CAT inlined function to replace the ERR_PTR(PTR_ERR). It
make the code more concise.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The coresight drivers relied on default bindings for graph
in DT, while reusing the "reg" field of the "ports" to indicate
the actual hardware port number for the connections. This can
cause duplicate ports with same addresses, but different
direction. However, with the rules getting stricter for the
address mismatch with the label, it is no longer possible to use
the port address field for the hardware port number.
This patch introduces new DT binding rules for coresight
components, based on the same generic DT graph bindings, but
avoiding the address duplication.
- All output ports must be specified under a child node with
name "out-ports".
- All input ports must be specified under a childe node with
name "in-ports".
- Port address should match the hardware port number.
The support for legacy bindings is retained, with a warning.
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The platform code parses the component connections and populates
a platform-description of the output connections in arrays of fields
(which is never freed). This is later copied in the coresight_register
to a newly allocated area, represented by coresight_connection(s).
This patch cleans up the code dealing with connections by making
use of the "coresight_connection" structure right at the platform
code and lets the generic driver simply re-use information provided
by the platform.
Thus making it reader friendly as well as avoiding the wastage of
unused memory.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a helper to check if the given endpoint is input.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When parsing the remote endpoint of an output port, we do :
rport = of_graph_get_remote_port(ep);
rparent = of_graph_get_remote_port_parent(ep);
and then parse the "remote_port" as if it was the remote endpoint,
which is wrong. The code worked fine because we used endpoint number
as the port number. Let us fix it and optimise a bit as:
remote_ep = of_graph_get_remote_endpoint(ep);
if (remote_ep)
remote_parent = of_graph_get_port_parent(remote_ep);
and then, parse the remote_ep for the port/endpoint details.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't drop the reference on the remote device while parsing the
connection, held by bus_find_device(). Fix this by duplicating the
device name and dropping the reference.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Kim Phillips <kim.phillips@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The coresight driver doesn't drop the references on the
remote endpoint/port nodes. Add the missing of_node_put()
calls.
Reported-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor the of graph endpoint parsing code, to make the error
handling easier.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6403587a930c ("coresight: use put_device() instead of kfree()")
fixes the double freeing of resources and ensures that the device
refcount is dropped properly. Add a comment to explain this to
help the readers and prevent people trying to "unfix" it again.
While at it, rename the labels for better readability.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Probing the TPIU driver under UBSan triggers an out-of-bounds shift
warning in coresight_timeout():
...
[ 5.677530] UBSAN: Undefined behaviour in drivers/hwtracing/coresight/coresight.c:929:16
[ 5.685542] shift exponent 64 is too large for 64-bit type 'long unsigned int'
...
On closer inspection things are exponentially out of whack because we're
passing a bitmask where a bit number should be. Amusingly, it seems that
both calls will find their expected values by sheer luck and appear to
succeed: 1 << FFCR_FON_MAN ends up at bit 64 which whilst undefined
evaluates as zero in practice, while 1 << FFSR_FT_STOPPED finds bit 2
(TCPresent) which apparently is usually tied high.
Following the examples of other drivers, define separate FOO and FOO_BIT
macros for masks vs. indices, and put things right.
CC: Robert Walker <robert.walker@arm.com>
CC: Mike Leach <mike.leach@linaro.org>
CC: Mathieu Poirier <mathieu.poirier@linaro.org>
Fixes: 11595db8e1 ("coresight: Fix disabling of CoreSight TPIU")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we can use a CATU with a scatter gather table, add support
for the TMC ETR to make use of the connected CATU in translate mode.
This is done by adding CATU as new buffer mode.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the support for setting up a SG table for use
by the CATU. We reuse the tmc_sg_table to represent the table/data
pages, even though the table format is different.
Similar to ETR SG table, CATU uses a 4KB page size for data buffers
as well as page tables. All table entries are 64bit wide and have
the following format:
63 12 1 0
x-----------------------------------x
| Address [63-12] | SBZ | V |
x-----------------------------------x
Where [V] -> 0 - Pointer is invalid
1 - Pointer is Valid
CATU uses only first half of the page for data page pointers.
i.e, single table page will only have 256 page pointers, addressing
upto 1MB of data. The second half of a table page contains only two
pointers at the end of the page (i.e, pointers at index 510 and 511),
which are used as links to the "Previous" and "Next" page tables
respectively.
The first table page has an "Invalid" previous pointer and the
next pointer entry points to the second page table if there is one.
Similarly the last table page has an "Invalid" next pointer to
indicate the end of the table chain.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the initial support for Coresight Address Translation Unit, which
augments the TMC in Coresight SoC-600 by providing an improved Scatter
Gather mechanism. CATU is always connected to a single TMC-ETR and
converts the AXI address with a translated address (from a given SG
table with specific format). The CATU should be programmed in pass
through mode and enabled even if the ETR doesn't use the translation
by CATU.
This patch provides mechanism to enable/disable the CATU always in the
pass through mode.
We reuse the existing ports mechanism to link the TMC-ETR to the
connected CATU.
i.e, TMC-ETR:output_port0 -> CATU:input_port0
Reference manual for CATU component is avilable in version r2p0 of :
"Arm Coresight System-on-Chip SoC-600 Technical Reference Manual".
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new coresight device type, which do not belong to any
of the existing types, i.e, source, sink, link etc. A helper
device could be connected to a coresight device, which could
augment the functionality of the coresight device.
This is intended to cover Coresight Address Translation Unit (CATU)
devices, which provide improved Scatter Gather mechanism for TMC
ETR. The idea is that the helper device could be controlled by
the driver of the device it is attached to (in this case ETR),
transparent to the generic coresight driver (and paths).
The operations include enable(), disable(), both of which could
accept a device specific "data" which the driving device and
the helper device could share. Since they don't appear in the
coresight "path" tracked by software, we have to ensure that
they are powered up/down whenever the master device is turned
on.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we fail to find the input / output port for a LINK component
while enabling a path, we should fail gracefully rather than
assuming port "0".
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We request for "CORESIGHT_BARRIER_PKT_SIZE" length and we should
be happy when we get that size.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The newly introduced code fails to build in some configurations
unless we include the right headers:
drivers/hwtracing/coresight/coresight-tmc-etr.c: In function 'tmc_free_table_pages':
drivers/hwtracing/coresight/coresight-tmc-etr.c:206:3: error: implicit declaration of function 'vunmap'; did you mean 'iounmap'? [-Werror=implicit-function-declaration]
Fixes: 79613ae8715a ("coresight: Add generic TMC sg table framework")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we can dynamically switch between contiguous memory and
SG table depending on the trace buffer size, provide the support
for selecting an appropriate buffer size.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the support for Scatter-Gather mode to the etr-buf layer.
Since we now have two different modes, we choose the backend
based on a set of conditions, documented in the code.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TMC-ETR can use the target trace buffer in two different modes.
Normal physically contiguous mode and a discontiguous list pages in
Scatter-Gather mode. Also we have dedicated Coresight component, CATU
(Coresight Address Translation Unit) to provide improved scatter-gather
mode in Coresight SoC-600. This complicates the management of the
buffer used for trace, depending on the mode in which ETR is configured.
So, this patch adds a transparent layer for managing the ETR buffer
which abstracts the basic operations on the buffer (alloc, free,
sync and retrieve the data) and uses the mode specific helpers to
do the actual operation. This also allows the ETR driver to choose
the best mode for a given use case and adds the flexibility to
fallback to a different mode, without duplicating the code.
The patch also adds the "normal" flat memory mode and switches
the sysfs driver to use the new layer.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for setting up an SG table used by the
TMC ETR inbuilt SG unit. The TMC ETR uses 4K page sized tables
to hold pointers to the 4K data pages with the last entry in a
table pointing to the next table with the entries, by kind of
chaining. The 2 LSBs determine the type of the table entry, to
one of :
Normal - Points to a 4KB data page.
Last - Points to a 4KB data page, but is the last entry in the
page table.
Link - Points to another 4KB table page with pointers to data.
The code takes care of handling the system page size which could
be different than 4K. So we could end up putting multiple ETR
SG tables in a single system page, vice versa for the data pages.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces a generic sg table data structure and
associated operations. An SG table can be used to map a set
of Data pages where the trace data could be stored by the TMC
ETR. The information about the data pages could be stored in
different formats, depending on the type of the underlying
SG mechanism (e.g, TMC ETR SG vs Coresight CATU). The generic
structure provides book keeping of the pages used for the data
as well as the table contents. The table should be filled by
the user of the infrastructure.
A table can be created by specifying the number of data pages
as well as the number of table pages required to hold the
pointers, where the latter could be different for different
types of tables. The pages are mapped in the appropriate dma
data direction mode (i.e, DMA_TO_DEVICE for table pages
and DMA_FROM_DEVICE for data pages). The framework can optionally
accept a set of allocated data pages (e.g, perf ring buffer) and
map them accordingly. The table and data pages are vmap'ed to allow
easier access by the drivers. The framework also provides helpers to
sync the data written to the pages with appropriate directions.
This will be later used by the TMC ETR SG unit and CATU.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are about to add the support for ETR builtin scatter-gather mode
for dealing with large amount of trace buffers. However, on some of
the platforms, using the ETR SG mode can lock up the system due to
the way the ETR is connected to the memory subsystem.
In SG mode, the ETR performs READ from the scatter-gather table to
fetch the next page and regular WRITE of trace data. If the READ
operation doesn't complete(due to the memory subsystem issues,
which we have seen on a couple of platforms) the trace WRITE
cannot proceed leading to issues. So, we by default do not
use the SG mode, unless it is known to be safe on the platform.
We define a DT property for the TMC node to specify whether we
have a proper SG mode.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: John Horley <john.horley@arm.com>
Cc: Robert Walker <robert.walker@arm.com>
Cc: devicetree@vger.kernel.org
Cc: frowand.list@gmail.com
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now we open code filling the trace buffer with synchronization
packets when the circular buffer wraps around in different drivers.
Move this to a common place. While at it, clean up the barrier_pkt
array to strip off the trailing '\0'.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't support ETR in perf mode yet. So, don't
even try to enable the hardware, even by mistake.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We zero out the entire trace buffer used for ETR before it is enabled,
for helping with debugging. With the addition of scatter-gather mode,
the buffer could be bigger and non-contiguous.
Get rid of this step; if someone wants to debug, they can always add it
as and when needed.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the moment we adjust the buffer pointers for reading the trace
data via misc device in the common code for ETF/ETB and ETR. Since
we are going to change how we manage the buffer for ETR, let us
move the buffer manipulation to the respective driver files, hiding
it from the common code. We do so by adding type specific helpers
for finding the length of data and the pointer to the buffer,
for a given length at a file position.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ETM PIDs of the Arm cortex-A CPUs to the white list of ETMs.
While at it add a helper macro to make it easier to add the new
entries.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As with ETM3x, the ETM4x tracers can trigger trace acquisition based on
contextID value, something that isn't useful when PID namespaces are
enabled. Indeed the PID value of a process has a different representation
in the kernel and the PID namespace, making the feature confusing and
potentially leaking internal kernel information.
As such simply return an error when the feature is being used from a
PID namespace other than the default one.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Kim Phillips <kim.phillips@arm.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tracers can trigger trace acquisition based on contextID value, something
that isn't useful when PID namespaces are enabled. Indeed the PID value
of a process has a different representation in the kernel and the PID
namespace, making the feature confusing and potentially leaking internal
kernel information.
As such simply return an error when the feature is being used from a
PID namespace other than the default one.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Kim Phillips <kim.phillips@arm.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver prints pcsr twice: the first time it uses specifier %px to
print hexadecimal pcsr value and the second time uses specifier %pS for
output kernel symbols.
As suggested by Kees, using %pS should be sufficient and %px isn't
necessary; the reason is if the pcsr is a kernel space address, we can
easily get to know the code line from %pS format, on the other hand, if
the pcsr value doesn't fall into kernel space range (e.g. if the CPU is
stuck in firmware), %pS also gives out pcsr hexadecimal value.
So this commit removes useless %px and update section "Output format"
in the document for alignment between the code and document.
Suggested-by: Kees Cook <keescook@chromium.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The simple removal of an extra newline, no change in functionality.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable 'paddr' can't be used if uninitialised but is nonetheless
confusing to some static checker. As such simply initialise it to zero.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While operating from sysFS the TMC-ETR driver needs to make sure it has
memory to work with but doesn't allocate memory uselessly either. Since
the main memory handle for this driver is drvdata::vaddr, use it throughout
function tmc_enable_etr_sink_sysfs() so that things are consistent.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moving all kernel side CoreSight framework and drivers to SPDX identifier.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Never directly free @dev after calling device_register(), even
if it returned an error. Always use put_device() to give up the
reference initialized.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of char/misc driver patches for 4.17-rc1.
There are a lot of little things in here, nothing huge, but all
important to the different hardware types involved:
- thunderbolt driver updates
- parport updates (people still care...)
- nvmem driver updates
- mei updates (as always)
- hwtracing driver updates
- hyperv driver updates
- extcon driver updates
- and a handfull of even smaller driver subsystem and individual
driver updates
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWsShSQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykNqwCfUbfvopswb1PesHCLABDBsFQChgoAniDa6pS9
kI8TN5MdLN85UU27Mkb6
=BzFR
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big set of char/misc driver patches for 4.17-rc1.
There are a lot of little things in here, nothing huge, but all
important to the different hardware types involved:
- thunderbolt driver updates
- parport updates (people still care...)
- nvmem driver updates
- mei updates (as always)
- hwtracing driver updates
- hyperv driver updates
- extcon driver updates
- ... and a handful of even smaller driver subsystem and individual
driver updates
All of these have been in linux-next with no reported issues"
* tag 'char-misc-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (149 commits)
hwtracing: Add HW tracing support menu
intel_th: Add ACPI glue layer
intel_th: Allow forcing host mode through drvdata
intel_th: Pick up irq number from resources
intel_th: Don't touch switch routing in host mode
intel_th: Use correct method of finding hub
intel_th: Add SPDX GPL-2.0 header to replace GPLv2 boilerplate
stm class: Make dummy's master/channel ranges configurable
stm class: Add SPDX GPL-2.0 header to replace GPLv2 boilerplate
MAINTAINERS: Bestow upon myself the care for drivers/hwtracing
hv: add SPDX license id to Kconfig
hv: add SPDX license to trace
Drivers: hv: vmbus: do not mark HV_PCIE as perf_device
Drivers: hv: vmbus: respect what we get from hv_get_synint_state()
/dev/mem: Avoid overwriting "err" in read_mem()
eeprom: at24: use SPDX identifier instead of GPL boiler-plate
eeprom: at24: simplify the i2c functionality checking
eeprom: at24: fix a line break
eeprom: at24: tweak newlines
eeprom: at24: refactor at24_probe()
...
This is a cosmetic patch that deals with the address filter structure's
ambiguous fields 'filter' and 'range'. The former stands to mean that the
filter's *action* should be to filter the traces to its address range if
it's set or stop tracing if it's unset. This is confusing and hard on the
eyes, so this patch replaces it with 'action' enum. The 'range' field is
completely redundant (meaning that the filter is an address range as
opposed to a single address trigger), as we can use zero size to mean the
same thing.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: Will Deacon <will.deacon@arm.com>
Link: http://lkml.kernel.org/r/20180329120648.11902-1-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
ctxid_pid and vmid_val in config are of type u64. When an integer
0xFF is being left shifted more than 32 bits, the behavior is
undefined. The fix is to specify 0xFF as an unsigned long.
Detected by Coverity scan: CID 37650, 37651 (Bad bit shift operation)
Signed-off-by: Bo Yan <byan@nvidia.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ad67b74d24 ("printk: hash addresses printed with %p") lets
printk specifier %p to hash all addresses before printing, this was
resulting in the high 32 bits of pcsr can only output zeros. So
module cannot completely print pc value and it's pointless for debugging
purpose.
This patch fixes this by using %px to print pcsr instead.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big pull request for char/misc drivers for 4.16-rc1.
There's a lot of stuff in here. Three new driver subsystems were added
for various types of hardware busses:
- siox
- slimbus
- soundwire
as well as a new vboxguest subsystem for the VirtualBox hypervisor
drivers.
There's also big updates from the FPGA subsystem, lots of Android binder
fixes, the usual handful of hyper-v updates, and lots of other smaller
driver updates.
All of these have been in linux-next for a long time, with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLuZw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynS4QCcCrPmwfD5PJwaF+q2dPfyKaflkQMAn0x6Wd+u
Gw3Z2scgjETUpwJ9ilnL
=xcQ0
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big pull request for char/misc drivers for 4.16-rc1.
There's a lot of stuff in here. Three new driver subsystems were added
for various types of hardware busses:
- siox
- slimbus
- soundwire
as well as a new vboxguest subsystem for the VirtualBox hypervisor
drivers.
There's also big updates from the FPGA subsystem, lots of Android
binder fixes, the usual handful of hyper-v updates, and lots of other
smaller driver updates.
All of these have been in linux-next for a long time, with no reported
issues"
* tag 'char-misc-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (155 commits)
char: lp: use true or false for boolean values
android: binder: use VM_ALLOC to get vm area
android: binder: Use true and false for boolean values
lkdtm: fix handle_irq_event symbol for INT_HW_IRQ_EN
EISA: Delete error message for a failed memory allocation in eisa_probe()
EISA: Whitespace cleanup
misc: remove AVR32 dependencies
virt: vbox: Add error mapping for VERR_INVALID_NAME and VERR_NO_MORE_FILES
soundwire: Fix a signedness bug
uio_hv_generic: fix new type mismatch warnings
uio_hv_generic: fix type mismatch warnings
auxdisplay: img-ascii-lcd: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
uio_hv_generic: add rescind support
uio_hv_generic: check that host supports monitor page
uio_hv_generic: create send and receive buffers
uio: document uio_hv_generic regions
doc: fix documentation about uio_hv_generic
vmbus: add monitor_id and subchannel_id to sysfs per channel
vmbus: fix ABI documentation
uio_hv_generic: use ISR callback method
...
Reuse the new generic helper, of_cpu_node_to_id() to map a
given CPU phandle to a logical CPU number.
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
These duplicate includes have been found with scripts/checkincludes.pl but
they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CoreSight TPIU should be disabled when tracing to other sinks to allow
them to operate at full bandwidth.
This patch fixes tpiu_disable_hw() to correctly disable the TPIU by
configuring the TPIU to stop on flush, initiating a manual flush, waiting
for the flush to complete and then waits for the TPIU to indicate it has
stopped.
Signed-off-by: Robert Walker <robert.walker@arm.com>
Tested-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix ptr_ret.cocci warnings:
drivers/hwtracing/coresight/coresight-tpiu.c:163:1-3: WARNING: PTR_ERR_OR_ZERO can be used
drivers/hwtracing/coresight/coresight-funnel.c:217:1-3: WARNING: PTR_ERR_OR_ZERO can be used
drivers/hwtracing/coresight/coresight-dynamic-replicator.c:166:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to reinvent the wheel, we have bus_find_device_by_name().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of char/misc and other driver subsystem patches for
4.15-rc1.
There are small changes all over here, hyperv driver updates, pcmcia
driver updates, w1 driver updats, vme driver updates, nvmem driver
updates, and lots of other little one-off driver updates as well. The
shortlog has the full details.
Note, there will be a merge conflict in drivers/misc/lkdtm_core.c when
merging to your tree as one lkdtm patch came in through the perf tree as
well as this one. The resolution is to take the const change that this
tree provides.
All of these have been in linux-next for quite a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWg2Lnw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymTUwCgwp46+I8yPlgDH8oe5TxyyJnpdHQAn1XW0i+a
sBi6WS87In5v1QO1Rgfc
=dH2a
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big set of char/misc and other driver subsystem patches
for 4.15-rc1.
There are small changes all over here, hyperv driver updates, pcmcia
driver updates, w1 driver updats, vme driver updates, nvmem driver
updates, and lots of other little one-off driver updates as well. The
shortlog has the full details.
All of these have been in linux-next for quite a while with no
reported issues"
* tag 'char-misc-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (90 commits)
VME: Return -EBUSY when DMA list in use
w1: keep balance of mutex locks and refcnts
MAINTAINERS: Update VME subsystem tree.
nvmem: sunxi-sid: add support for A64/H5's SID controller
nvmem: imx-ocotp: Update module description
nvmem: imx-ocotp: Enable i.MX7D OTP write support
nvmem: imx-ocotp: Add i.MX7D timing write clock setup support
nvmem: imx-ocotp: Move i.MX6 write clock setup to dedicated function
nvmem: imx-ocotp: Add support for banked OTP addressing
nvmem: imx-ocotp: Pass parameters via a struct
nvmem: imx-ocotp: Restrict OTP write to IMX6 processors
nvmem: uniphier: add UniPhier eFuse driver
dt-bindings: nvmem: add description for UniPhier eFuse
nvmem: set nvmem->owner to nvmem->dev->driver->owner if unset
nvmem: qfprom: fix different address space warnings of sparse
nvmem: mtk-efuse: fix different address space warnings of sparse
nvmem: mtk-efuse: use stack for nvmem_config instead of malloc'ing it
nvmem: imx-iim: use stack for nvmem_config instead of malloc'ing it
thunderbolt: tb: fix use after free in tb_activate_pcie_devices
MAINTAINERS: Add git tree for Thunderbolt development
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per coresight standards, PIDR2 register has the following format :
[2-0] - JEP106_bits6to4
[3] - JEDEC, designer ID is specified by JEDEC.
However some of the drivers only use mask of 0x3 for the PIDR2 leaving
bits [3-2] unchecked, which could potentially match the component for
a different device altogether. This patch fixes the mask and the
corresponding id bits for the existing devices.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The casting and other things here is odd, and causes sparse to
complain:
drivers/hwtracing/coresight/coresight-stm.c:279:35: warning: incorrect type in argument 1 (different address spaces)
drivers/hwtracing/coresight/coresight-stm.c:279:35: expected void [noderef] <asn:2>*addr
drivers/hwtracing/coresight/coresight-stm.c:279:35: got struct stm_drvdata *drvdata
drivers/hwtracing/coresight/coresight-stm.c:327:17: warning: incorrect type in argument 2 (different address spaces)
drivers/hwtracing/coresight/coresight-stm.c:327:17: expected void volatile [noderef] <asn:2>*addr
drivers/hwtracing/coresight/coresight-stm.c:327:17: got void *addr
drivers/hwtracing/coresight/coresight-stm.c:330:17: warning: incorrect type in argument 2 (different address spaces)
drivers/hwtracing/coresight/coresight-stm.c:330:17: expected void volatile [noderef] <asn:2>*addr
drivers/hwtracing/coresight/coresight-stm.c:330:17: got void *addr
drivers/hwtracing/coresight/coresight-stm.c:333:17: warning: incorrect type in argument 2 (different address spaces)
drivers/hwtracing/coresight/coresight-stm.c:333:17: expected void volatile [noderef] <asn:2>*addr
drivers/hwtracing/coresight/coresight-stm.c:333:17: got void *addr
>From what I can tell, we don't really need to treat ch_addr as
anything besides a pointer, and we can just do pointer math
instead of ORing in the bits of the offset and achieve the same
thing.
Also, we were passing a drvdata pointer to the
coresight_timeout() function, but we really wanted to pass the
address of the register base. Luckily the base is the first
member of the structure, so everything works out, but this is
quite unsafe if we ever change the structure layout. Clean this
all up so sparse stops complaining on this code.
Reported-by: Satyajit Desai <sadesai@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The coresight SoC 600 supports ETR save-restore which allows us
to restore a trace session by retaining the RRP/RWP/STS.Full values
when the TMC leaves the Disabled state. However, the TMC doesn't
have a scatter-gather unit in built.
Also, TMCs have different PIDs in different configurations (ETF,
ETB & ETR), unlike the previous generation.
While the DEVID exposes some of the features/changes in the TMC,
it doesn't explicitly advertises the new save-restore feature
as described above.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Coresight SoC 600 TMC ETR supports save-restore feature,
where the values of the RRP/RWP and STS.Full are retained
when it leaves the Disabled state. Hence, we must program the
RRP/RWP and STS.Full to a proper value. For now, set the RRP/RWP
to the base address of the buffer and clear the STS.Full register.
This can be later exploited for proper save-restore of ETR
trace contexts (e.g, perf).
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the ETR supports split cache encoding (i.e, separate bits for
read and write transfers) unlike the older version (where read
and write transfers use the same encoding in AXICTL[2-5]).
This feature is not advertised and has to be described by the
static mask associated with the device id.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch cleans up how we setup the AXICTL register on
TMC ETR. At the moment we don't set the CacheCtrl bits, which
drives the arcache and awcache bits on AXI bus specifying the
cacheablitiy. Set this to Write-back Read and Write-allocate.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TMC in Coresight SoC-600 advertises the AXI address width
in the device configuration register.
Bit 16 - AXIAW_VALID
0 - AXI Address Width not valid
1 - Valid AXI Address width in Bits[23-17]
Bits [23-17] - AXIAW. If AXIAW_VALID = b01 then
0x20 - 32bit AXI address bus
0x28 - 40bit AXI address bus
0x2c - 44bit AXI address bus
0x30 - 48bit AXI address bus
0x34 - 52bit AXI address bus
Use the address bits from the device configuration register, if
available. Otherwise, default to 40bit.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SG unit in the TMC has been removed in Coresight SoC-600.
This is however advertised by DEVID:Bit 24 = 0b1. On the
previous generation, the bit is RES0, hence we can rely on the
DEVID to detect the support.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With new version of TMC ETR, there are differing set of
features supported by the TMC. Add the capability of a
given TMC ETR for making safer decisions at runtime.
The device configuration register of the TMC (DEVID) lists
some of the capabilities. So, we can detect some of them at
probe. However, some of the features (or changes in behavior)
are not advertised and we have to depend on the PID to infer
the features. So we use a static description of the "unadvertised"
capabilities attached to the PID. Combining both, the static
and the dynamic capabilities, we maintain a bitmask of the
available features which can be later checked to take
appropriate actions.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coresight SoC 600 defines a new configuration for TMC, Embedded Trace
Streamer (ETS), indicated by 0x3 in MODE:CONFIG_TYPE. This would break
the existing driver which will treat anything other than ETR/ETB as an
ETF. Fix the driver to check the configuration type properly and also
add a warning if we encounter an unsupported configuration (ETS).
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coresight TMC splits 64bit registers into a pair of 32bit registers
(e.g DBA, RRP, RWP). Provide helpers to read/write to these registers.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new helpers for exposing coresight component registers,
choosing the 64bit variants for appropriate registers.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for reading a lower and upper 32bits of a register
as a single 64bit register. Also add simplified macros for
direct register accesses.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Linux coresight drivers define the programmable ATB replicator as
Qualcomm replicator, while this is designed by ARM. This can cause
confusion to a user selecting the driver. Cleanup all references to
make it explicitly clear. This patch :
1) Replace the compatible string for the replicator :
qcom,coresight-replicator1x => arm,coresight-dynamic-replicator
2) Changes the Kconfig symbol (since this is not part of any defconfigs)
CORESIGHT_QCOM_REPLICATOR => CORESIGHT_DYNAMIC_REPLICATOR
3) Improves the help message in the Kconfig.
4) Changes the name of the driver and the file :
coresight-replicator-qcom => coresight-dynamic-replicator
Cc: Pratik Patel <pratikp@codeaurora.org>
Cc: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: devicetree@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds handling to program the return stack option into ETMv4 hardware if
specified in the perf command line.
If option is not supported by the hardware then it will be ignored.
This allows capture to move between core/ETM combinations that have the
hardware support to those that do not.
Signed-off-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds handling to program the return stack option into PTM hardware if
specified in the perf command line.
If option is not supported by the hardware then it will be ignored.
This allows capture to move between core/ETM combinations that have the
hardware support to those that do not.
Signed-off-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return stack is a programmable option on some ETM and PTM hardware.
Adds the option flags to enable this from the perf event command line.
Signed-off-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
2573 288 296 3157 c55 coresight-etm-perf.o
File size After adding 'const':
text data bss dec hex filename
2613 224 296 3133 c3d coresight-etm-perf.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register ETMSYNCFR holds the number of by that need to be generated before
periodic synchronisation packets are inserted in the trace stream. By
zeroing out the config structure, the current code effectively disable
periodic synchronization.
This patch simply initialise the recommended value for this register as
specified in the technical reference manual.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function etb_disable_hw() is already taking care of unlocking and locking
the coresight access register and as such doesn't need to be placed
within the unlock/lock of function etb_update_buffer().
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a buffer overflow happens the synchronisation patckets usually
present at the beginning of the buffer are lost, a situation that
prevents the decoder from knowing the context of the traces being
decoded.
This patch adds a barrier packet to be used by sink IPs when a buffer
overflow condition is detected. These barrier packets are then used
by the decoding library as markers to force re-synchronisation.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Internal CoreSight components are rendering trace data in little-endian
format. As such there is no need to convert the data once more, hence
removing the extra step.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many conditions may cause synchronisation to be lost when updating
the perf ring buffer but the end result is still the same: synchronisation
is lost. As such there is no need to increment the lost count for each
condition, just once will suffice.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the "big" char/misc driver patchset for 4.13-rc1.
Lots of stuff in here, a large thunderbolt update, w1 driver header
reorg, the new mux driver subsystem, google firmware driver updates, and
a raft of other smaller things. Full details in the shortlog.
All of these have been in linux-next for a while with the only reported
issue being a merge problem with this tree and the jc-docs tree in the
w1 documentation area. The fix should be obvious for what to do when it
happens, if not, we can send a follow-up patch for it afterward.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpXKA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynLrQCdG9SxRjAbOd6pT9Fr2NAzpUG84YsAoLw+I3iO
EMi60UXWqAFJbtVMS9Aj
=yrSq
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the "big" char/misc driver patchset for 4.13-rc1.
Lots of stuff in here, a large thunderbolt update, w1 driver header
reorg, the new mux driver subsystem, google firmware driver updates,
and a raft of other smaller things. Full details in the shortlog.
All of these have been in linux-next for a while with the only
reported issue being a merge problem with this tree and the jc-docs
tree in the w1 documentation area"
* tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (147 commits)
misc: apds990x: Use sysfs_match_string() helper
mei: drop unreachable code in mei_start
mei: validate the message header only in first fragment.
DocBook: w1: Update W1 file locations and names in DocBook
mux: adg792a: always require I2C support
nvmem: rockchip-efuse: add support for rk322x-efuse
nvmem: core: add locking to nvmem_find_cell
nvmem: core: Call put_device() in nvmem_unregister()
nvmem: core: fix leaks on registration errors
nvmem: correct Broadcom OTP controller driver writes
w1: Add subsystem kernel public interface
drivers/fsi: Add module license to core driver
drivers/fsi: Use asynchronous slave mode
drivers/fsi: Add hub master support
drivers/fsi: Add SCOM FSI client device driver
drivers/fsi/gpio: Add tracepoints for GPIO master
drivers/fsi: Add GPIO based FSI master
drivers/fsi: Document FSI master sysfs files in ABI
drivers/fsi: Add error handling for slave
drivers/fsi: Add tracepoints for low-level operations
...
Coresight includes debug module and usually the module connects with CPU
debug logic. ARMv8 architecture reference manual (ARM DDI 0487A.k) has
description for related info in "Part H: External Debug".
Chapter H7 "The Sample-based Profiling Extension" introduces several
sampling registers, e.g. we can check program counter value with
combined CPU exception level, secure state, etc. So this is helpful for
analysis CPU lockup scenarios, e.g. if one CPU has run into infinite
loop with IRQ disabled. In this case the CPU cannot switch context and
handle any interrupt (including IPIs), as the result it cannot handle
SMP call for stack dump.
This patch is to enable coresight debug module, so firstly this driver
is to bind apb clock for debug module and this is to ensure the debug
module can be accessed from program or external debugger. And the driver
uses sample-based registers for debug purpose, e.g. when system triggers
panic, the driver will dump program counter and combined context
registers (EDCIDSR, EDVIDSR); by parsing context registers so can
quickly get to know CPU secure state, exception level, etc.
Some of the debug module registers are located in CPU power domain, so
this requires the CPU power domain stays on when access related debug
registers, but the power management for CPU power domain is quite
dependent on SoC integration for power management. For the platforms
which with sane power controller implementations, this driver follows
the method to set EDPRCR to try to pull the CPU out of low power state
and then set 'no power down request' bit so the CPU has no chance to
lose power.
If the SoC has not followed up this design well for power management
controller, the user should use the command line parameter or sysfs
to constrain all or partial idle states to ensure the CPU power
domain is enabled and access coresight CPU debug component safely.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is refactor to add function of_coresight_get_cpu(), so it's used to
retrieve CPU id for coresight component. Finally can use it as a common
function for multiple places.
Suggested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The of_get_coresight_platform_data iterates over the possible CPU nodes
to find a given cpu phandle. However it does not drop the reference
to the node pointer returned by the of_get_coresight_platform_data.
This patch also introduces another minor fix is to use
of_cpu_device_node_get() to replace of_get_cpu_node().
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[Leo: minor tweaks for of_get_coresight_platform_data]
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before making any DMA API calls, the ETR driver should really be setting
its masks to ensure that DMA is possible. Especially since it can
address more than the 32-bit default mask set by the AMBA bus code.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Delete a character in this description for a condition check.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Link: http://events.linuxfoundation.org/sites/events/files/slides/LCJ16-Refactor_Strings-WSang_0.pdf
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Almost low level functions from open firmware have used const to
qualify device_node structures, so add const for device_node
parameters in of_coresight related functions.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In current code the output logs are not well symmetric for sink and link
enabling and disabling. This patch is to fix that so can output paired
logs.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For software sources (i.e STM), there could be multiple agents
generating the trace data, unlike the ETMs. So we need to
properly do the accounting for the active number of users
to disable the device when the last user goes away. Right
now, the reference counting is broken for sources as we skip
the actions when we detect that the source is enabled.
This patch fixes the problem by adding the refcounting for
software sources, even when they are enabled.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Reported-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With a coresight tracing session, the components along the path
from the source to sink are disabled after the source is disabled.
However, if the source was not actually disabled due to active
users, we should not disable the components in the path.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
etm_probe4() holds get_online_cpus() while invoking
cpuhp_setup_state_nocalls().
cpuhp_setup_state_nocalls() invokes get_online_cpus() as well. This is
correct, but prevents the conversion of the hotplug locking to a percpu
rwsem.
Use cpuhp_setup_state_nocalls_cpuslocked() to avoid the nested
call. Convert *_online_cpus() to the new interfaces while at it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/20170524081547.983493849@linutronix.de
etm_probe() holds get_online_cpus() while invoking
cpuhp_setup_state_nocalls().
cpuhp_setup_state_nocalls() invokes get_online_cpus() as well. This is
correct, but prevents the conversion of the hotplug locking to a percpu
rwsem.
Use cpuhp_setup_state_nocalls_cpuslocked() to avoid the nested
call. Convert *_online_cpus() to the new interfaces while at it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/20170524081547.889092478@linutronix.de
Here is the big set of new char/misc driver drivers and features for
4.12-rc1.
There's lots of new drivers added this time around, new firmware drivers
from Google, more auxdisplay drivers, extcon drivers, fpga drivers, and
a bunch of other driver updates. Nothing major, except if you happen to
have the hardware for these drivers, and then you will be happy :)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWQvAgg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yknsACgzkAeyz16Z97J3UTaeejbR7nKUCAAoKY4WEHY
8O9f9pr9gj8GMBwxeZQa
=OIfB
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of new char/misc driver drivers and features for
4.12-rc1.
There's lots of new drivers added this time around, new firmware
drivers from Google, more auxdisplay drivers, extcon drivers, fpga
drivers, and a bunch of other driver updates. Nothing major, except if
you happen to have the hardware for these drivers, and then you will
be happy :)
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (136 commits)
firmware: google memconsole: Fix return value check in platform_memconsole_init()
firmware: Google VPD: Fix return value check in vpd_platform_init()
goldfish_pipe: fix build warning about using too much stack.
goldfish_pipe: An implementation of more parallel pipe
fpga fr br: update supported version numbers
fpga: region: release FPGA region reference in error path
fpga altera-hps2fpga: disable/unprepare clock on error in alt_fpga_bridge_probe()
mei: drop the TODO from samples
firmware: Google VPD sysfs driver
firmware: Google VPD: import lib_vpd source files
misc: lkdtm: Add volatile to intentional NULL pointer reference
eeprom: idt_89hpesx: Add OF device ID table
misc: ds1682: Add OF device ID table
misc: tsl2550: Add OF device ID table
w1: Remove unneeded use of assert() and remove w1_log.h
w1: Use kernel common min() implementation
uio_mf624: Align memory regions to page size and set correct offsets
uio_mf624: Refactor memory info initialization
uio: Allow handling of non page-aligned memory regions
hangcheck-timer: Fix typo in comment
...
Corrected to get the port numbering to allow programmable replicator driver
to operate correctly.
By convention, CoreSight devices number ports, not endpoints in
the .dts files:-
port {
reg<N>
endpoint {
}
}
Existing code read endpoint number - always 0x0, rather than the correct
port number.
Signed-off-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for adding more flags to perf AUX records, introduce a
separate API for setting the flags for a session, rather than appending
more bool arguments to perf_aux_output_end. This allows to set each
flag at the time a corresponding condition is detected, instead of
tracking it in each driver's private state.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: vince@deater.net
Link: http://lkml.kernel.org/r/20170220133352.17995-3-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When using the ETM4x tracers from the perf interface two trace options are
available: cycle accurate and timestamp.
Enabling the timestamp feature is done by setting TRCCONFIGR.TS (bit 11).
The position of the timestamp bit in that register coincidentally happens
to be the same as what was chosen to enable timestamping from the 'mode'
sysFS entry. The code does the right thing but the semantic is wrong.
This patch sets TRCCONFIGR.TS explicitly, as it is done from the sysFS
interface. That way timestamps are set the same way from both perf and
sysFS and there is no misunderstanding as to what is intended.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using perf record 'cyclacc' option in cs_etm event was not setting up cycle
accurate trace correctly.
Corrects bit set in TRCCONFIGR to enable cycle accurate trace.
Programs TRCCCCTLR with a valid threshold value as required by ETMv4 spec.
Signed-off-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suzuki K Poulose