* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
not overwriting file_lock structure after GET_LK
cifs: Fix a kernel BUG with remote OS/2 server (try #3)
[CIFS] initialize nbytes at the beginning of CIFSSMBWrite()
[CIFS] Add mmap for direct, nobrl cifs mount types
Back in commit 04a0551c87
("loopback: Drop obsolete ip_summed setting") we stopped
setting CHECKSUM_UNNECESSARY in the loopback xmit.
This is because such a setting was a lie since it implies that the
checksum field of the packet is properly filled in.
Instead what happens normally is that CHECKSUM_PARTIAL is set and
skb->csum is calculated as needed.
But this was only happening for TCP data packets (via the
skb->ip_summed assignment done in tcp_sendmsg()). It doesn't
happen for non-data packets like ACKs etc.
Fix this by setting skb->ip_summed in the common non-data packet
constructor. It already is setting skb->csum to zero.
But this reminds us that we still have things like ip_output.c's
ip_dev_loopback_xmit() which sets skb->ip_summed to the value
CHECKSUM_UNNECESSARY, which Herbert's patch teaches us is not
valid. So we'll have to address that at some point too.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commits 5051ebd275 and
5051ebd275 ("ipv[46]: udp: optimize unicast RX
path") broke some programs.
After upgrading a L2TP server to 2.6.33 it started to fail, tunnels going up an
down, after the 10th tunnel came up. My modified rp-l2tp uses a global
unconnected socket bound to (INADDR_ANY, 1701) and one connected socket per
tunnel after parameter negotiation.
After ten sockets were open and due to mixed parameters to
udp[46]_lib_lookup2() kernel started to drop packets.
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Timo Teräs <timo.teras@iki.fi>
Happens because CONFIG_XFRM_SUB_POLICY is not enabled, and one of
the helper functions I used did unexpected things in that case.
Signed-off-by: David S. Miller <davem@davemloft.net>
When we fetch the hot regs and rewind to the nth caller, it
might happen that we dereference a frame pointer outside the
kernel stack boundaries, like in this example:
perf_trace_sched_switch+0xd5/0x120
schedule+0x6b5/0x860
retint_careful+0xd/0x21
Since we directly dereference a userspace frame pointer here while
rewinding behind retint_careful, this may end up in a crash.
Fix this by simply using probe_kernel_address() when we rewind the
frame pointer.
This issue will have a much more proper fix in the next version of the
perf_arch_fetch_caller_regs() API that will only need to rewind to the
first caller.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: David Miller <davem@davemloft.net>
Cc: Archs <linux-arch@vger.kernel.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: Fix accesses at LBA28 boundary (old bug, but nasty) (v2)
Most drives from Seagate, Hitachi, and possibly other brands,
do not allow LBA28 access to sector number 0x0fffffff (2^28 - 1).
So instead use LBA48 for such accesses.
This bug could bite a lot of systems, especially when the user has
taken care to align partitions to 4KB boundaries. On misaligned systems,
it is less likely to be encountered, since a 4KB read would end at
0x10000000 rather than at 0x0fffffff.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-2.6:
ide: Fix IDE taskfile with cfq scheduler
ide: Must hold queue lock when requeueing
ide: Requeue request after DMA timeout
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI / PM: Move ACPI video resume to a PM notifier
ACPI: Reduce ACPI resource conflict message to KERN_WARNING, printk cleanup
ACPI: battery drivers should call power_supply_changed()
ACPI: battery: Fix CONFIG_ACPI_SYSFS_POWER=n
PNPACPI: truncate _CRS windows with _LEN > _MAX - _MIN + 1
ACPI: Don't send KEY_UNKNOWN for random video notifications
ACPI: NUMA: map pxms to low node ids
ACPI: use _HID when supplied by root-level devices
ACPI / ACPICA: Do not check reference counters in acpi_ev_enable_gpe()
ACPI: fixes a false alarm from lockdep
ACPI dock: support multiple ACPI dock devices
ACPI: EC: Allow multibyte access to EC
Using a regular timer results in poll times < 1 jiffie with small
buffers, so we loaded the timer with the actual jiffie value. We can
be more accurate using a hrtimer. Also, we have to call
snd_pcm_period_elapsed after playing period_bytes and not
runtime->period_size (which is in samples and not in bytes).
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When checking if we are DMA capable we have to check for the
IMX_SSI_DMA flag which is already set from platform_data instead
of setting it again when we want to do DMA.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@Slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
generic setattr not longer responsible for quota transfer.
use udf_setattr for all udf's inodes.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jan Kara <jack@suse.cz>
bloc->logicalBlockNum is unsigned so it's never less than zero.
When I saw that, it made me worry that "bloc->logicalBlockNum + count"
could overflow. That's why I changed the check for less than zero
to an overflow check. (The test works because "count" is also
unsigned.)
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
- max_config_dev loadable parameter is set to 0xFF by default. Pass correct
number of VFs value to pci_sriov_enable() if max_config_dev is set to its
default value.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@exar.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Allow all instances of the driver be loaded when multiple pci functions are
enumerated. The max_config_dev driver loadable option limits the driver
load instances if required. The X3100's function configuration of single/multi
function, SR and MR IOV allows the user to select the number of pci functions.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@exar.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix a possible memory leak in vxge_hw_device_initialize(). Free hldev if
vxge_hw_device_reg_addr_get() fails.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@exar.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix rx_pause management in myri10ge_set_pauseparam().
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix coding style errors and warnings output while running checkpatch.pl
on the files net/core/ethtool.c and include/linux/ethtool.h
Signed-off-by: chavey <chavey@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable BIG bit in the network configuration register, so the MAC
doesn't reject big frames (E.G. when vlans are used).
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current documentation for hardware time stamping does not
correctly specify the available kernel functions since the
implementation was changed later on.
Signed-off-by: Patrick Loschmidt <Patrick.Loschmidt@oeaw.ac.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resource size should be calculated as end - start + 1 because we start
counting at zero. I changed the code to resource_size() to do the
calculation.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current X.25 code has some bugs in throughput negotiation:
1. It does negotiation in all cases, usually there is no need
2. It incorrectly attempts to negotiate the throughput class in one
direction only. There are separate throughput classes for input
and output and if either is negotiated both mist be negotiates.
This is bug https://bugzilla.kernel.org/show_bug.cgi?id=15681
This bug was first reported by Daniel Ferenci to the linux-x25 mailing
list on 6/8/2004, but is still present.
The current (2.6.34) x.25 code doesn't seem to know that the X.25
throughput facility includes two values, one for the required
throughput outbound, one for inbound.
This causes it to attempt to negotiate throughput 0x0A, which is
throughput 9600 inbound and the illegal value "0" for inbound
throughput.
Because of this some X.25 devices (e.g. Cisco 1600) refuse to connect
to Linux X.25.
The following patch fixes this behaviour. Unless the user specifies a
required throughput it does not attempt to negotiate. If the user
does not specify a throughput it accepts the suggestion of the remote
X.25 system. If the user requests a throughput then it validates both
the input and output throughputs and correctly negotiates them with
the remote end.
Signed-off-by: John Hughes <john@calva.com>
Tested-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is a patch to stop X.25 examining fields beyond the end of the packet.
For example, when a simple CALL ACCEPTED was received:
10 10 0f
x25_parse_facilities was attempting to decode the FACILITIES field, but this
packet contains no facilities field.
Signed-off-by: John Hughes <john@calva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IGMP3 report parsing is looking at the wrong address for
group records. This patch fixes it.
Reported-by: Banyeer <banyeer@yahoo.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA API is preferred.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Vladislav Zolotarov <vladz@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move sg structure off stack and into virtnet_info structure.
This helps remove extra sg_init_table calls as well as reduce
stack usage.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
benet driver wrongly assumes that zero is an invalid dma address
(calls dma_unmap_page for only non zero dma addresses). Zero is a
valid dma address on some architectures. The dma length can be used
here.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA API is preferred.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver attempts to select an IRQ for the NIC automatically by
testing which of the supported IRQs are available and then probing
each available IRQ with probe_irq_{on,off}(). There are obvious race
conditions here, besides which:
1. The test for availability is done by passing a NULL handler, which
now always returns -EINVAL, thus the device cannot be opened:
<http://bugs.debian.org/566522>
2. probe_irq_off() will report only the first ISA IRQ handled,
potentially leading to a false negative.
There was another bug that meant it ignored all error codes from
request_irq() except -EBUSY, so it would 'succeed' despite this
(possibly causing conflicts with other ISA devices). This was fixed
by ab08999d60 'WARNING: some
request_irq() failures ignored in el2_open()', which exposed bug 1.
This patch:
1. Replaces the use of probe_irq_{on,off}() with a real interrupt handler
2. Adds a delay before checking the interrupt-seen flag
3. Disables interrupts on all failure paths
4. Distinguishes error codes from the second request_irq() call,
consistently with the first
Compile-tested only.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
cnic_service_bnx2x() irq handler can be called during chip reset from
MTU change. Need to check that the cnic's device state is up before
handling the irq.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
hvc_console: Fix race between hvc_close and hvc_remove
virtio: disable multiport console support.
virtio: console makes incorrect assumption about virtio API
virtio: console: Fix early_put_chars usage
MAINTAINERS: Put the virtio-console entry in correct alphabetical order
I don't claim to understand the tty layer, but it seems like hvc_open and
hvc_close should be balanced in their kref reference counting.
Right now we get a kref every call to hvc_open:
if (hp->count++ > 0) {
tty_kref_get(tty); <----- here
spin_unlock_irqrestore(&hp->lock, flags);
hvc_kick();
return 0;
} /* else count == 0 */
tty->driver_data = hp;
hp->tty = tty_kref_get(tty); <------ or here if hp->count was 0
But hvc_close has:
tty_kref_get(tty);
if (--hp->count == 0) {
...
/* Put the ref obtained in hvc_open() */
tty_kref_put(tty);
...
}
tty_kref_put(tty);
Since the outside kref get/put balance we only do a single kref_put when
count reaches 0.
The patch below changes things to call tty_kref_put once for every
hvc_close call, and with that my machine boots fine.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Move MULTIPORT feature and related config changes
out of exported headers, and disable the feature
at runtime.
At this point, it seems less risky to keep code around
until we can enable it than rip it out completely.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The get_buf() API sets the second arg to the number of bytes *written*
by the other side; in this case it should be zero as these are output buffers.
lguest gets this right (obviously kvm's console doesn't), resulting in
continual buildup of console writes.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Amit Shah <amit.shah@redhat.com>
Currently early_put_chars is not used by virtio_console because it can
only be used once a port has been found, at which point it's too late
because it is no longer needed. This patch should fix it.
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Move around the entry for virtio-console to keep the file sorted.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
If interface is down, mac address request are not sent to fw
but it is getting add in driver mac list.
Driver mac list should be in sync with fw i.e addresses communicated
to fw.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported in <https://bugzilla.kernel.org/show_bug.cgi?id=15355>, r6040_
multicast_list currently crashes. This is due a wrong maximum of multicast
entries. This patch fixes the following issues with multicast:
- number of maximum entries if off-by-one (4 instead of 3)
- the writing of the hash table index is not necessary and leads to invalid
values being written into the MCR1 register, so the MAC is simply put in a non
coherent state
- when we exceed the maximum number of mutlticast address, writing the
broadcast address should be done in registers MID_1{L,M,H} instead of
MID_O{L,M,H}, otherwise we would loose the adapter's MAC address
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I don't think this can be abused in this case but do things properly.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
write is optional for a tty device. Check that we have a write op rather
than calling NULL.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed by Randy Dunlap, we must include linux/proc_fs.h in
net/core/dev_addr_lists.c, regardless of CONFIG_PROC_FS
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>,
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds