Originally there were several implementations of PHY operations for the
several different PHYs used on Falcon boards. But Falcon is now in a
separate driver, and all sfc NICs since then have had MCDI-managed PHYs.
Thus, there is no need to indirect through function pointers in
efx->phy_op; we can simply call the efx_mcdi_phy_* functions directly.
This also hooks up these functions for EF100, which was previously using
the dummy_phy_ops.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dev_close(), by way of ef100_net_stop(), already brings down the filter
table, so there's no need to do it again (which just causes lots of
WARN_ONs).
Similarly, don't bring it up ourselves, as dev_open() -> ef100_net_open()
will do it, and will fail if it's already been brought up.
Fixes: a9dc3d5612 ("sfc_ef100: RX filter table management and related gubbins")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/dnet.c: In function dnet_start_xmit
drivers/net/ethernet/dnet.c:511:15: warning: variable ‘len’ set but not used [-Wunused-but-set-variable]
commit 4796417417 ("dnet: Dave DNET ethernet controller driver (updated)")
involved this unused variable, remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Because clk_prepare_enable() and clk_disable_unprepare() already checked
NULL clock parameter, so the additional checks are unnecessary, just
remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Because clk_prepare_enable() and clk_disable_unprepare() already checked
NULL clock parameter, so the additional checks are unnecessary, just
remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Because clk_prepare_enable() and clk_disable_unprepare() already checked
NULL clock parameter, so the additional checks are unnecessary, just
remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Because clk_prepare_enable() and clk_disable_unprepare() already checked
NULL clock parameter, so the additional checks are unnecessary, just
remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov says:
====================
net: bridge: mcast: initial IGMPv3/MLDv2 support (part 1)
This patch-set implements the control plane for initial IGMPv3/MLDv2
support which takes care of include/exclude sets and state transitions
based on the different report types.
Patch 01 arranges the structure better by moving the frequently used
fields together, patch 02 factors out the port group deletion code which is
used in a few places. Patches 03 and 04 add support for source lists and
group modes per port group which are dumped. Patch 05 adds support for
group-and-source specific queries required for IGMPv3/MLDv2. Then patch 06
adds support for group and group-and-source query retransmissions via a new
rexmit timer. Patches 07 and 08 make use of the already present mdb fill
functions when sending notifications so we can have the full mdb entries'
state filled in (with sources, mode etc). Patch 09 takes care of port group
expiration, it switches the group mode to include and deletes it if there
are no sources with active timers. Patches 10-13 are the core changes which
add support for IGMPv3/MLDv2 reports and handle the source list set
operations as per RFCs 3376 and 3810, all IGMPv3/MLDv2 report types with
their transitions should be supported after these patches. I've used RFCs
3376, 3810 and FRR as a reference implementation. The source lists are
capped at 32 entries, we can remove that limitation at a later point which
would require a better data structure to hold them. IGMPv3 processing is
hidden behind the bridge's multicast_igmp_version option which must be set
to 3 in order to enable it. MLDv2 processing is hidden behind the bridge's
multicast_mld_version which must be set to 2 in order to enable it.
Patch 14 improves other querier processing a bit (more about this below).
And finally patch 15 transforms the src gc so it can be used with all mcast
objects since now we have multiple timers that can be running and we
need to make sure they have all finished before freeing the objects.
This is part 1, it only adds control plane support and doesn't change
the fast path. A following patch-set will take care of that.
Here're the sets that will come next (in order):
- Fast path patch-set which adds support for (S, G) mdb entries needed
for IGMPv3/MLDv2 forwarding, entry add source (kernel, user-space etc)
needed for IGMPv3/MLDv2 entry management, entry block mode needed for
IGMPv3/MLDv2 exclude mode. This set will also add iproute2 support for
manipulating and showing all the new state.
- Selftests patches which will verify all state transitions and forwarding
- Explicit host tracking patch-set, needed for proper fast leave and
with it fast leave will be enabled for IGMPv3/MLDv2
Not implemented yet:
- Host IGMPv3/MLDv2 filter support (currently we handle only join/leave
as before)
- Proper other querier source timer and value updates
- IGMPv3/v2 MLDv2/v1 compat (I have a few rough patches for this one)
v4: move old patch 05 to 02 (group del patch), before src lists
patch 02: set pg's fast leave flag when deleting due to fast leave
patch 03: now can use the new port del function
add igmpv2/mldv1 bool which are set when the entry is
added in those modes (later will be passed as update_timer)
patch 10: rename update_timer to igmpv2_mldv1 and use the passed
value from br_multicast_add_group's callers
v3: add IPv6/MLDv2 support, most patches are changed
v2:
patches 03-04: make src lists RCU friendly so they can be traversed
when dumping, reduce limit to a more conservative 32
src group entries for a start
patches 11-13: remove helper and directly do bitops
patch 15: force mcast gc on bridge port del to make sure port
group timers have finished before freeing the port
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since each entry type has timers that can be running simultaneously we need
to make sure that entries are not freed before their timers have finished.
In order to do that generalize the src gc work to mcast gc work and use a
callback to free the entries (mdb, port group or src).
v3: add IPv6 support
v2: force mcast gc on port del to make sure all port group timers have
finished before freeing the bridge port
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When an IGMPv3/MLDv2 query is received and we're operating in such mode
then we need to avoid updating group timers if the suppress flag is set.
Also we should update only timers for groups in exclude mode.
v3: add IPv6/MLDv2 support
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We already have all necessary helpers, so process IGMPV3/MLDv2
BLOCK_OLD_SOURCES as per the RFCs.
v3: add IPv6/MLDv2 support
v2: directly do flag bit operations
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to process IGMPV3/MLDv2 CHANGE_TO_INCLUDE/EXCLUDE report types we
need new helpers which allow us to mark entries based on their timer
state and to query only marked entries.
v3: add IPv6/MLDv2 support, fix other_query checks
v2: directly do flag bit operations
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to process IGMPV3/MLDv2_MODE_IS_INCLUDE/EXCLUDE report types we
need some new helpers which allow us to set/clear flags for all current
entries and later delete marked entries after the report sources have been
processed.
v3: add IPv6/MLDv2 support
v2: drop flag helpers and directly do flag bit operations
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds handling for the ALLOW_NEW_SOURCES IGMPv3/MLDv2 report
types and limits them only when multicast_igmp_version == 3 or
multicast_mld_version == 2 respectively. Now that IGMPv3/MLDv2 handling
functions will be managing timers we need to delay their activation, thus
a new argument is added which controls if the timer should be updated.
We also disable host IGMPv3/MLDv2 handling as it's not yet implemented and
could cause inconsistent group state, the host can only join a group as
EXCLUDE {} or leave it.
v4: rename update_timer to igmpv2_mldv1 and use the passed value from
br_multicast_add_group's callers
v3: Add IPv6/MLDv2 support
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If an expired port group is in EXCLUDE mode, then we have to turn it
into INCLUDE mode, remove all srcs with zero timer and finally remove
the group itself if there are no more srcs with an active timer.
For IGMPv2 use there would be no sources, so this will reduce to just
removing the group as before.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We have to use mdb and port entries when sending mdb notifications in
order to fill in all group attributes properly. Before this change we
would've used a fake br_mdb_entry struct to fill in only partial
information about the mdb. Now we can also reuse the mdb dump fill
function and thus have only a single central place which fills the mdb
attributes.
v3: add IPv6 support
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This change is in preparation for using the mdb port group entries when
sending a notification, so their full state and additional attributes can
be filled in.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We need to be able to retransmit group-specific and group-and-source
specific queries. The new timer takes care of those.
v3: add IPv6 support
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allows br_multicast_alloc_query to build queries with the port group's
source lists and sends a query for sources over and under lmqt when
necessary as per RFCs 3376 and 3810 with the suppress flag set
appropriately.
v3: add IPv6 support
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Support per port group src list (address and timer) and filter mode
dumping. Protected by either multicast_lock or rcu.
v3: add IPv6 support
v2: require RCU or multicast_lock to traverse src groups
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Initial functions for group source lists which are needed for IGMPv3
and MLDv2 include/exclude lists. Both IPv4 and IPv6 sources are supported.
User-added mdb entries are created with exclude filter mode, we can
extend that later to allow user-supplied mode. When group src entries
are deleted, they're freed from a workqueue to make sure their timers
are not still running. Source entries are protected by the multicast_lock
and rcu. The number of src groups per port group is limited to 32.
v4: use the new port group del function directly
add igmpv2/mldv1 bool to denote if the entry was added in those
modes, it will later replace the old update_timer bool
v3: add IPv6 support
v2: allow src groups to be traversed under rcu
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to avoid future errors and reduce code duplication we should
factor out the port group del sequence. This allows us to have one
function which takes care of all details when removing a port group.
v4: set pg's fast leave flag when deleting due to fast leave
move the patch before adding source lists
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before this patch we'd need 2 cache lines for fast-path, now all used
fields are in the first cache line.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This switches the RTL8366RB over to using phylink callbacks
instead of .adjust_link(). This is a pretty template
switchover. All we adjust is the CPU port so that is why
the code only inspects this port.
We enhance by adding proper error messages, also disabling
the CPU port on the way down and moving dev_info() to
dev_dbg().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the commit fdeba99b1e
("tipc: fix use-after-free in tipc_bcast_get_mode"), we're trying
to make sure the tipc_net_finalize_work work item finished if it
enqueued. But calling flush_scheduled_work() is not just affecting
above work item but either any scheduled work. This has turned out
to be overkill and caused to deadlock as syzbot reported:
======================================================
WARNING: possible circular locking dependency detected
5.9.0-rc2-next-20200828-syzkaller #0 Not tainted
------------------------------------------------------
kworker/u4:6/349 is trying to acquire lock:
ffff8880aa063d38 ((wq_completion)events){+.+.}-{0:0}, at: flush_workqueue+0xe1/0x13e0 kernel/workqueue.c:2777
but task is already holding lock:
ffffffff8a879430 (pernet_ops_rwsem){++++}-{3:3}, at: cleanup_net+0x9b/0xb10 net/core/net_namespace.c:565
[...]
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(pernet_ops_rwsem);
lock(&sb->s_type->i_mutex_key#13);
lock(pernet_ops_rwsem);
lock((wq_completion)events);
*** DEADLOCK ***
[...]
v1:
To fix the original issue, we replace above calling by introducing
a bit flag. When a namespace cleaned-up, bit flag is set to zero and:
- tipc_net_finalize functionial just does return immediately.
- tipc_net_finalize_work does not enqueue into the scheduled work queue.
v2:
Use cancel_work_sync() helper to make sure ONLY the
tipc_net_finalize_work() stopped before releasing bcbase object.
Reported-by: syzbot+d5aa7e0385f6a5d0f4fd@syzkaller.appspotmail.com
Fixes: fdeba99b1e ("tipc: fix use-after-free in tipc_bcast_get_mode")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Hoang Huu Le <hoang.h.le@dektech.com.au>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Setting F2 block size to 128 bytes for BCM4329 allows to significantly
improve RX throughput on NVIDIA Tegra20. Before this change the throughput
was capped to 30 Mbit/s on Tegra, now throughput is at 40 Mbit/s, which is
a maximum throughput for the BCM4329 chip. The F2 block size is borrowed
from the downstream BCMDHD driver. The comment in the BCMDHD driver says
that 128B improves throughput and turns out that it works for the brcmfmac
as well.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200830191439.10017-4-digetx@gmail.com
The chip ID was already printed out at the time when debug message about
the changed F2 watermark is printed, hence let's drop the unnecessary part
of the debug messages. This cleans code a tad and also allows to re-use
the F2 watermark debug messages by multiple chips.
Suggested-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200830191439.10017-3-digetx@gmail.com
This patch fixes SDHCI CRC errors during of RX throughput testing on
BCM4329 chip if SDIO BUS is clocked above 25MHz. In particular the
checksum problem is observed on NVIDIA Tegra20 SoCs. The good watermark
value is borrowed from downstream BCMDHD driver and it's matching to the
value that is already used for the BCM4339 chip, hence let's re-use it
for BCM4329.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200830191439.10017-2-digetx@gmail.com
These variables only used in sdio.c, move them to .c file
can silence these warnings:
In file included from drivers/net/wireless/marvell/mwifiex//main.h:59:0,
from drivers/net/wireless/marvell/mwifiex//cfp.c:24:
drivers/net/wireless/marvell/mwifiex//sdio.h:705:41: warning: ‘mwifiex_sdio_sd8801’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8801 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:689:41: warning: ‘mwifiex_sdio_sd8987’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8987 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:674:41: warning: ‘mwifiex_sdio_sd8887’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8887 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:658:41: warning: ‘mwifiex_sdio_sd8997’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8997 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:642:41: warning: ‘mwifiex_sdio_sd8977’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8977 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:627:41: warning: ‘mwifiex_sdio_sd8897’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8897 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:612:41: warning: ‘mwifiex_sdio_sd8797’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8797 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:597:41: warning: ‘mwifiex_sdio_sd8787’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8787 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:582:41: warning: ‘mwifiex_sdio_sd8786’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8786 = {
^~~~~~~~~~~~~~~~~~~
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200902141155.30144-1-yuehaibing@huawei.com
In file included from drivers/net/wireless/marvell/mwifiex//cmdevt.c:26:0:
drivers/net/wireless/marvell/mwifiex//wmm.h:41:17: warning: ‘tos_to_tid_inv’ defined but not used [-Wunused-const-variable=]
static const u8 tos_to_tid_inv[] = {
^~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//wmm.h:34:18: warning: ‘mwifiex_1d_to_wmm_queue’ defined but not used [-Wunused-const-variable=]
static const u16 mwifiex_1d_to_wmm_queue[8] = { 1, 0, 0, 1, 2, 2, 3, 3 };
^~~~~~~~~~~~~~~~~~~~~~~
move the variables definition to .c file, and leave declarations
in the header file to fix these warnings.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200902140846.29024-1-yuehaibing@huawei.com
Remove function return type const in rtw8821c_get_swing_index().
This is unused, and unnecessary to be const.
All warnings (new ones prefixed by >>):
>> drivers/net/wireless/realtek/rtw88/rtw8821c.c:71:8: warning: type
qualifiers ignored on function return type [-Wignored-qualifiers]
71 | static const u8 rtw8821c_get_swing_index(struct rtw_dev *rtwdev)
| ^~~~~
Fixes: f745eb9ca5 ("rtw88: 8821c: Add 8821CE to Kconfig and Makefile")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200902053402.12839-1-yhchuang@realtek.com
A new warning in clang points out when macro expansion might result in a
GNU C statement expression. There is an instance of this in the mwifiex
driver:
drivers/net/wireless/marvell/mwifiex/cmdevt.c:217:34: warning: '}' and
')' tokens terminating statement expression appear in different macro
expansion contexts [-Wcompound-token-split-by-macro]
host_cmd->seq_num = cpu_to_le16(HostCmd_SET_SEQ_NO_BSS_INFO
^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex/fw.h:519:46: note: expanded from
macro 'HostCmd_SET_SEQ_NO_BSS_INFO'
(((type) & 0x000f) << 12); }
^
This does not appear to be a real issue. Removing the braces and
replacing them with parentheses will fix the warning and not change the
meaning of the code.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/1146
Reported-by: Andy Lavr <andy.lavr@gmail.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200901070834.1015754-1-natechancellor@gmail.com
The wrappers in include/linux/pci-dma-compat.h should go away.
The patch has been generated with the coccinelle script below and has been
hand modified to replace GFP_ with a correct flag.
It has been compile tested.
When memory is allocated in 'vnic_dev_classifier()', 'vnic_dev_fw_info()',
'vnic_dev_notify_set()' and 'vnic_dev_stats_dump()' (vnic_dev.c) GFP_ATOMIC
must be used because its callers take a spinlock before calling these
functions.
When memory is allocated in '__enic_set_rsskey()' and 'enic_set_rsscpu()'
GFP_ATOMIC must be used because they can be called with a spinlock.
The call chain is:
enic_reset <-- takes 'enic->enic_api_lock'
--> enic_set_rss_nic_cfg
--> enic_set_rsskey
--> __enic_set_rsskey <-- uses dma_alloc_coherent
--> enic_set_rsscpu <-- uses dma_alloc_coherent
When memory is allocated in 'vnic_dev_init_prov2()' GFP_ATOMIC must be used
because a spinlock is hidden in the ENIC_DEVCMD_PROXY_BY_INDEX macro, when
this function is called in 'enic_set_port_profile()'.
When memory is allocated in 'vnic_dev_alloc_desc_ring()' GFP_KERNEL can be
used because it is only called from 5 functions ('vnic_dev_init_devcmd2()',
'vnic_cq_alloc()', 'vnic_rq_alloc()', 'vnic_wq_alloc()' and
'enic_wq_devcmd2_alloc()'.
'vnic_dev_init_devcmd2()': already uses GFP_KERNEL and no lock is taken
in the between.
'enic_wq_devcmd2_alloc()': is called from ' vnic_dev_init_devcmd2()'
which already uses GFP_KERNEL and no lock is taken in the between.
'vnic_cq_alloc()', 'vnic_rq_alloc()', 'vnic_wq_alloc()': are called
from 'enic_alloc_vnic_resources()'
'enic_alloc_vnic_resources()' has only 2 call chains:
1) enic_probe
--> enic_dev_init
--> enic_alloc_vnic_resources
'enic_probe()' is a probe function and no lock is taken in the between
2) enic_set_ringparam
--> enic_alloc_vnic_resources
'enic_set_ringparam()' is a .set_ringparam function (see struct
ethtool_ops). It seems to only take a mutex and no spinlock.
So all paths are safe to use GFP_KERNEL.
@@
@@
- PCI_DMA_BIDIRECTIONAL
+ DMA_BIDIRECTIONAL
@@
@@
- PCI_DMA_TODEVICE
+ DMA_TO_DEVICE
@@
@@
- PCI_DMA_FROMDEVICE
+ DMA_FROM_DEVICE
@@
@@
- PCI_DMA_NONE
+ DMA_NONE
@@
expression e1, e2, e3;
@@
- pci_alloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3;
@@
- pci_zalloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3, e4;
@@
- pci_free_consistent(e1, e2, e3, e4)
+ dma_free_coherent(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_single(e1, e2, e3, e4)
+ dma_map_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_single(e1, e2, e3, e4)
+ dma_unmap_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4, e5;
@@
- pci_map_page(e1, e2, e3, e4, e5)
+ dma_map_page(&e1->dev, e2, e3, e4, e5)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_page(e1, e2, e3, e4)
+ dma_unmap_page(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_sg(e1, e2, e3, e4)
+ dma_map_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_sg(e1, e2, e3, e4)
+ dma_unmap_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+ dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_device(e1, e2, e3, e4)
+ dma_sync_single_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+ dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+ dma_sync_sg_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2;
@@
- pci_dma_mapping_error(e1, e2)
+ dma_mapping_error(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_dma_mask(e1, e2)
+ dma_set_mask(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_consistent_dma_mask(e1, e2)
+ dma_set_coherent_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It's nice if the phy is online before we register the netdev
so try to do that first.
Stop trying to do "second tried" to register the phy, it
works perfectly fine the first time.
Stop remvoving the phy in uninit. Remove it when the
driver is remove():d, symmetric to where it is added, in
probe().
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This implements the missing MTU setting for the RTL8366RB
switch.
Apart from supporting jumboframes, this rids us of annoying
boot messages like this:
realtek-smi switch: nonfatal error -95 setting MTU on port 0
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BLOCK_PRIV is never used after it was introduced.
So better to remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
DIGITAL_NFC_DEP_REQ_RES_TAILROOM is never used after it was introduced.
DIGITAL_NFC_DEP_REQ_RES_HEADROOM is no more used after below
commit e8e7f42175 ("NFC: digital: Remove useless call to skb_reserve()")
Remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove SRVL_CTRL_PKT_SIZE which is defined more than once.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 0da4c3d393 ("net: phy: add Lynx PCS module") added the files in
./drivers/net/pcs/, but the new LYNX PCS MODULE section refers to
./drivers/net/phy/.
Hence, ./scripts/get_maintainer.pl --self-test=patterns complains:
warning: no file matches F: drivers/net/phy/pcs-lynx.c
Repair the LYNX PCS MODULE section by referring to the right location.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Florian Fainelli says:
====================
net: dsa: bcm_sf2: Ensure MDIO diversion is used
Changes in v2:
- export of_update_property() to permit building bcm_sf2 as a module
- provided a better explanation of the problem being solved after
explaining it to Andrew during the v1 review
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Registering our slave MDIO bus outside of the OF infrastructure is
necessary in order to avoid creating double references of the same
Device Tree nodes, however it is not sufficient to guarantee that the
MDIO bus diversion is used because of_phy_connect() will still resolve
to a valid PHY phandle and it will connect to the PHY using its parent
MDIO bus which is still the SF2 master MDIO bus. The reason for that is
because BCM7445 systems were already shipped with a Device Tree blob
looking like this (irrelevant parts omitted for simplicity):
ports {
#address-cells = <1>;
#size-cells = <0>;
port@1 {
phy-mode = "rgmii-txid";
phy-handle = <&phy0>;
reg = <1>;
label = "rgmii_1";
};
...
mdio@403c0 {
...
phy0: ethernet-phy@0 {
broken-turn-around;
device_type = "ethernet-phy";
max-speed = <0x3e8>;
reg = <0>;
compatible = "brcm,bcm53125", "ethernet-phy-ieee802.3-c22";
};
};
There is a hardware issue with chip revisions (Dx) that lead to the
development of the following commits:
461cd1b03e ("net: dsa: bcm_sf2: Register our slave MDIO bus")
536fab5bf5 ("net: dsa: bcm_sf2: Do not register slave MDIO bus with OF")
b8c6cd1d31 ("net: dsa: bcm_sf2: do not use indirect reads and writes for 7445E0")
There should have been an internal MDIO bus node created for the chip
revision (Dx) that suffers from this problem, but it did not happen back
then.
Had that happen, that we should have correctly parented phy@0 (bcm53125
below) as child node of the internal MDIO bus, but the production Device
Tree blob that was shipped with the firmware targeted the fixed version
of the chip, despite both the affected and corrected chips being shipped
into production.
The problem is that of_phy_connect() for port@1 will happily resolve the
'phy-handle' from the mdio@403c0 node, which bypasses the diversion
completely. This results in this double programming that the diversion
refers to and aims to avoid. In order to force of_phy_connect() to fail,
and have DSA call to dsa_slave_phy_connect(), we must deactivate
ethernet-phy@0 from mdio@403c0, and the best way to do that is by
removing the phandle property completely.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We will need to remove some OF properties in drivers/net/dsa/bcm_sf2.c
with a subsequent commit. Export of_remove_property() to modules so we
can keep bcm_sf2 modular and provide an empty stub for when CONFIG_OF is
disabled to maintain the ability to compile test.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Edward Cree says:
====================
sfc: TXQ refactor
Refactor and unify partner-TXQ handling in the EF100 and legacy drivers.
The main thrust of this series is to remove from the legacy (Siena/EF10)
driver the assumption that a netdev TX queue has precisely two hardware
TXQs (checksummed and unchecksummed) associated with it, so that in
future we can have more (e.g. for handling inner-header checksums) or
fewer (e.g. to free up hardware queues for XDP usage).
Changes from v1:
* better explain patch #1 in the commit message, and rename
xmit_more_available to xmit_pending
* add new patch #2 applying the same approach to ef100, for consistency
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use efx_for_each_channel_tx_queue() rather than efx_tx_queue_partner().
Make some related simplifications of efx_nic_tx_is_empty() to remove
entry points that aren't used.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of open-coding the calculation with efx_tx_queue_partner(), use
the functions that iterate over numbers of queues other than 2 with
efx_for_each_channel_tx_queue().
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As in the Siena/EF10 case, it minimises cacheline ping-pong between
the TX and completion paths.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Edward Cree