We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from David Miller:
1) Use netif_rx_ni() when necessary in batman-adv stack, from Jussi
Kivilinna.
2) Fix loss of RTT samples in rxrpc, from David Howells.
3) Memory leak in hns_nic_dev_probe(), from Dignhao Liu.
4) ravb module cannot be unloaded, fix from Yuusuke Ashizuka.
5) We disable BH for too lokng in sctp_get_port_local(), add a
cond_resched() here as well, from Xin Long.
6) Fix memory leak in st95hf_in_send_cmd, from Dinghao Liu.
7) Out of bound access in bpf_raw_tp_link_fill_link_info(), from
Yonghong Song.
8) Missing of_node_put() in mt7530 DSA driver, from Sumera
Priyadarsini.
9) Fix crash in bnxt_fw_reset_task(), from Michael Chan.
10) Fix geneve tunnel checksumming bug in hns3, from Yi Li.
11) Memory leak in rxkad_verify_response, from Dinghao Liu.
12) In tipc, don't use smp_processor_id() in preemptible context. From
Tuong Lien.
13) Fix signedness issue in mlx4 memory allocation, from Shung-Hsi Yu.
14) Missing clk_disable_prepare() in gemini driver, from Dan Carpenter.
15) Fix ABI mismatch between driver and firmware in nfp, from Louis
Peens.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (110 commits)
net/smc: fix sock refcounting in case of termination
net/smc: reset sndbuf_desc if freed
net/smc: set rx_off for SMCR explicitly
net/smc: fix toleration of fake add_link messages
tg3: Fix soft lockup when tg3_reset_task() fails.
doc: net: dsa: Fix typo in config code sample
net: dp83867: Fix WoL SecureOn password
nfp: flower: fix ABI mismatch between driver and firmware
tipc: fix shutdown() of connectionless socket
ipv6: Fix sysctl max for fib_multipath_hash_policy
drivers/net/wan/hdlc: Change the default of hard_header_len to 0
net: gemini: Fix another missing clk_disable_unprepare() in probe
net: bcmgenet: fix mask check in bcmgenet_validate_flow()
amd-xgbe: Add support for new port mode
net: usb: dm9601: Add USB ID of Keenetic Plus DSL
vhost: fix typo in error message
net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init()
pktgen: fix error message with wrong function name
net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link mode
cxgb4: fix thermal zone device registration
...
syzbot is reporting hung task at nbd_ioctl() [1], for there are two
problems regarding TIPC's connectionless socket's shutdown() operation.
----------
#include <fcntl.h>
#include <sys/socket.h>
#include <sys/ioctl.h>
#include <linux/nbd.h>
#include <unistd.h>
int main(int argc, char *argv[])
{
const int fd = open("/dev/nbd0", 3);
alarm(5);
ioctl(fd, NBD_SET_SOCK, socket(PF_TIPC, SOCK_DGRAM, 0));
ioctl(fd, NBD_DO_IT, 0); /* To be interrupted by SIGALRM. */
return 0;
}
----------
One problem is that wait_for_completion() from flush_workqueue() from
nbd_start_device_ioctl() from nbd_ioctl() cannot be completed when
nbd_start_device_ioctl() received a signal at wait_event_interruptible(),
for tipc_shutdown() from kernel_sock_shutdown(SHUT_RDWR) from
nbd_mark_nsock_dead() from sock_shutdown() from nbd_start_device_ioctl()
is failing to wake up a WQ thread sleeping at wait_woken() from
tipc_wait_for_rcvmsg() from sock_recvmsg() from sock_xmit() from
nbd_read_stat() from recv_work() scheduled by nbd_start_device() from
nbd_start_device_ioctl(). Fix this problem by always invoking
sk->sk_state_change() (like inet_shutdown() does) when tipc_shutdown() is
called.
The other problem is that tipc_wait_for_rcvmsg() cannot return when
tipc_shutdown() is called, for tipc_shutdown() sets sk->sk_shutdown to
SEND_SHUTDOWN (despite "how" is SHUT_RDWR) while tipc_wait_for_rcvmsg()
needs sk->sk_shutdown set to RCV_SHUTDOWN or SHUTDOWN_MASK. Fix this
problem by setting sk->sk_shutdown to SHUTDOWN_MASK (like inet_shutdown()
does) when the socket is connectionless.
[1] https://syzkaller.appspot.com/bug?id=3fe51d307c1f0a845485cf1798aa059d12bf18b2
Reported-by: syzbot <syzbot+e36f41d207137b5d12f7@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the uses of fallthrough comments to fallthrough macro.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework the remaining setsockopt code to pass a sockptr_t instead of a
plain user pointer. This removes the last remaining set_fs(KERNEL_DS)
outside of architecture specific code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org> [ieee802154]
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple fixes which require no deep knowledge of the code.
Cc: Jon Maloy <jmaloy@redhat.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot found the following issue:
WARNING: CPU: 0 PID: 6808 at include/linux/thread_info.h:150 check_copy_size include/linux/thread_info.h:150 [inline]
WARNING: CPU: 0 PID: 6808 at include/linux/thread_info.h:150 copy_from_iter include/linux/uio.h:144 [inline]
WARNING: CPU: 0 PID: 6808 at include/linux/thread_info.h:150 tipc_msg_append+0x49a/0x5e0 net/tipc/msg.c:242
Kernel panic - not syncing: panic_on_warn set ...
This happens after commit 5e9eeccc58 ("tipc: fix NULL pointer
dereference in streaming") that tried to build at least one buffer even
when the message data length is zero... However, it now exposes another
bug that the 'mss' can be zero and the 'cpy' will be negative, thus the
above kernel WARNING will appear!
The zero value of 'mss' is never expected because it means Nagle is not
enabled for the socket (actually the socket type was 'SOCK_SEQPACKET'),
so the function 'tipc_msg_append()' must not be called at all. But that
was in this particular case since the message data length was zero, and
the 'send <= maxnagle' check became true.
We resolve the issue by explicitly checking if Nagle is enabled for the
socket, i.e. 'maxnagle != 0' before calling the 'tipc_msg_append()'. We
also reinforce the function to against such a negative values if any.
Reported-by: syzbot+75139a7d2605236b0b7f@syzkaller.appspotmail.com
Fixes: c0bceb97db ("tipc: add smart nagle feature")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_sendstream() may send zero length packet, then tipc_msg_append()
do not alloc skb, skb_peek_tail() will get NULL, msg_set_ack_required
will trigger NULL pointer dereference.
Reported-by: syzbot+8eac6d030e7807c21d32@syzkaller.appspotmail.com
Fixes: 0a3e060f34 ("tipc: add test for Nagle algorithm effectiveness")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid using kernel_setsockopt for the TIPC_IMPORTANCE option when we can
just use the internal helper. The only change needed is to pass a struct
sock instead of tipc_sock, which is private to socket.c
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When streaming in Nagle mode, we try to bundle small messages from user
as many as possible if there is one outstanding buffer, i.e. not ACK-ed
by the receiving side, which helps boost up the overall throughput. So,
the algorithm's effectiveness really depends on when Nagle ACK comes or
what the specific network latency (RTT) is, compared to the user's
message sending rate.
In a bad case, the user's sending rate is low or the network latency is
small, there will not be many bundles, so making a Nagle ACK or waiting
for it is not meaningful.
For example: a user sends its messages every 100ms and the RTT is 50ms,
then for each messages, we require one Nagle ACK but then there is only
one user message sent without any bundles.
In a better case, even if we have a few bundles (e.g. the RTT = 300ms),
but now the user sends messages in medium size, then there will not be
any difference at all, that says 3 x 1000-byte data messages if bundled
will still result in 3 bundles with MTU = 1500.
When Nagle is ineffective, the delay in user message sending is clearly
wasted instead of sending directly.
Besides, adding Nagle ACKs will consume some processor load on both the
sending and receiving sides.
This commit adds a test on the effectiveness of the Nagle algorithm for
an individual connection in the network on which it actually runs.
Particularly, upon receipt of a Nagle ACK we will compare the number of
bundles in the backlog queue to the number of user messages which would
be sent directly without Nagle. If the ratio is good (e.g. >= 2), Nagle
mode will be kept for further message sending. Otherwise, we will leave
Nagle and put a 'penalty' on the connection, so it will have to spend
more 'one-way' messages before being able to re-enter Nagle.
In addition, the 'ack-required' bit is only set when really needed that
the number of Nagle ACKs will be reduced during Nagle mode.
Testing with benchmark showed that with the patch, there was not much
difference in throughput for small messages since the tool continuously
sends messages without a break, so Nagle would still take in effect.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when a connection is in Nagle mode, we set the 'ack_required'
bit in the last sending buffer and wait for the corresponding ACK prior
to pushing more data. However, on the receiving side, the ACK is issued
only when application really reads the whole data. Even if part of the
last buffer is received, we will not do the ACK as required. This might
cause an unnecessary delay since the receiver does not always fetch the
message as fast as the sender, resulting in a large latency in the user
message sending, which is: [one RTT + the receiver processing time].
The commit makes Nagle ACK as soon as possible i.e. when a message with
the 'ack_required' arrives in the receiving side's stack even before it
is processed or put in the socket receive queue...
This way, we can limit the streaming latency to one RTT as committed in
Nagle mode.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the commit f73b12812a
("tipc: improve throughput between nodes in netns"), we're missing a check
to handle TIPC_DIRECT_MSG type, it's still using old sending mechanism for
this message type. So, throughput improvement is not significant as
expected.
Besides that, when sending a large message with that type, we're also
handle wrong receiving queue, it should be enqueued in socket receiving
instead of multicast messages.
Fix this by adding the missing case for TIPC_DIRECT_MSG.
Fixes: f73b12812a ("tipc: improve throughput between nodes in netns")
Reported-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 9546a0b7ce ("tipc: fix wrong connect() return code"), we
fixed the issue with the 'connect()' that returns zero even though the
connecting has failed by waiting for the connection to be 'ESTABLISHED'
really. However, the approach has one drawback in conjunction with our
'lightweight' connection setup mechanism that the following scenario
can happen:
(server) (client)
+- accept()| | wait_for_conn()
| | |connect() -------+
| |<-------[SYN]---------| > sleeping
| | *CONNECTING |
|--------->*ESTABLISHED | |
|--------[ACK]-------->*ESTABLISHED > wakeup()
send()|--------[DATA]------->|\ > wakeup()
send()|--------[DATA]------->| | > wakeup()
. . . . |-> recvq .
. . . . | .
send()|--------[DATA]------->|/ > wakeup()
close()|--------[FIN]-------->*DISCONNECTING |
*DISCONNECTING | |
| ~~~~~~~~~~~~~~~~~~> schedule()
| wait again
.
.
| ETIMEDOUT
Upon the receipt of the server 'ACK', the client becomes 'ESTABLISHED'
and the 'wait_for_conn()' process is woken up but not run. Meanwhile,
the server starts to send a number of data following by a 'close()'
shortly without waiting any response from the client, which then forces
the client socket to be 'DISCONNECTING' immediately. When the wait
process is switched to be running, it continues to wait until the timer
expires because of the unexpected socket state. The client 'connect()'
will finally get ‘-ETIMEDOUT’ and force to release the socket whereas
there remains the messages in its receive queue.
Obviously the issue would not happen if the server had some delay prior
to its 'close()' (or the number of 'DATA' messages is large enough),
but any kind of delay would make the connection setup/shutdown "heavy".
We solve this by simply allowing the 'connect()' returns zero in this
particular case. The socket is already 'DISCONNECTING', so any further
write will get '-EPIPE' but the socket is still able to read the
messages existing in its receive queue.
Note: This solution doesn't break the previous one as it deals with a
different situation that the socket state is 'DISCONNECTING' but has no
error (i.e. sk->sk_err = 0).
Fixes: 9546a0b7ce ("tipc: fix wrong connect() return code")
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current 'tipc_wait_for_connect()' function does a wait-loop for the
condition 'sk->sk_state != TIPC_CONNECTING' to conclude if the socket
connecting has done. However, when the condition is met, it returns '0'
even in the case the connecting is actually failed, the socket state is
set to 'TIPC_DISCONNECTING' (e.g. when the server socket has closed..).
This results in a wrong return code for the 'connect()' call from user,
making it believe that the connection is established and go ahead with
building, sending a message, etc. but finally failed e.g. '-EPIPE'.
This commit fixes the issue by changing the wait condition to the
'tipc_sk_connected(sk)', so the function will return '0' only when the
connection is really established. Otherwise, either the socket 'sk_err'
if any or '-ETIMEDOUT'/'-EINTR' will be returned correspondingly.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a socket is suddenly shutdown or released, it will reject all the
unreceived messages in its receive queue. This applies to a connected
socket too, whereas there is only one 'FIN' message required to be sent
back to its peer in this case.
In case there are many messages in the queue and/or some connections
with such messages are shutdown at the same time, the link layer will
easily get overflowed at the 'TIPC_SYSTEM_IMPORTANCE' backlog level
because of the message rejections. As a result, the link will be taken
down. Moreover, immediately when the link is re-established, the socket
layer can continue to reject the messages and the same issue happens...
The commit refactors the '__tipc_shutdown()' function to only send one
'FIN' in the situation mentioned above. For the connectionless case, it
is unavoidable but usually there is no rejections for such socket
messages because they are 'dest-droppable' by default.
In addition, the new code makes the other socket states clear
(e.g.'TIPC_LISTEN') and treats as a separate case to avoid misbehaving.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a user message is sent, TIPC will check if the socket has faced a
congestion at link layer. If that happens, it will make a sleep to wait
for the congestion to disappear. This leaves a gap for other users to
take over the socket (e.g. multi threads) since the socket is released
as well. Also, in case of connectionless (e.g. SOCK_RDM), user is free
to send messages to various destinations (e.g. via 'sendto()'), then
the socket's preformatted header has to be updated correspondingly
prior to the actual payload message building.
Unfortunately, the latter action is done before the first action which
causes a condition issue that the destination of a certain message can
be modified incorrectly in the middle, leading to wrong destination
when that message is built. Consequently, when the message is sent to
the link layer, it gets stuck there forever because the peer node will
simply reject it. After a number of retransmission attempts, the link
is eventually taken down and the retransmission failure is reported.
This commit fixes the problem by rearranging the order of actions to
prevent the race condition from occurring, so the message building is
'atomic' and its header will not be modified by anyone.
Fixes: 365ad353c2 ("tipc: reduce risk of user starvation during link congestion")
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scenario:
1. A client socket initiates a SYN message to a listening socket.
2. The send link is congested, the SYN message is put in the
send link and a wakeup message is put in wakeup queue.
3. The congestion situation is abated, the wakeup message is
pulled out of the wakeup queue. Function tipc_sk_push_backlog()
is called to send out delayed messages by Nagle. However,
the client socket is still in CONNECTING state. So, it sends
the SYN message in the socket write queue to the listening socket
again.
4. The listening socket receives the first SYN message and creates
first server socket. The client socket receives ACK- and establishes
a connection to the first server socket. The client socket closes
its connection with the first server socket.
5. The listening socket receives the second SYN message and creates
second server socket. The second server socket sends ACK- to the
client socket, but it has been closed. It results in connection
reset error when reading from the server socket in user space.
Solution: return from function tipc_sk_push_backlog() immediately
if there is pending SYN message in the socket write queue.
Fixes: c0bceb97db ("tipc: add smart nagle feature")
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function __tipc_shutdown(), the timeout value passed to
tipc_wait_for_cond() is not jiffies.
This commit fixes it by converting that value from milliseconds
to jiffies.
Fixes: 365ad353c2 ("tipc: reduce risk of user starvation during link congestion")
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tipc_sk_timeout() is executed but user space is grabbing
ownership, this function rearms itself and returns. However, the
socket reference counter is not reduced. This causes potential
unexpected behavior.
This commit fixes it by calling sock_put() before tipc_sk_timeout()
returns in the above-mentioned case.
Fixes: afe8792fec ("tipc: refactor function tipc_sk_timeout()")
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When initiating a connection message to a server side, the connection
message is cloned and added to the socket write queue. However, if the
cloning is failed, only the socket write queue is purged. It causes
memory leak because the original connection message is not freed.
This commit fixes it by purging the list of connection message when
it cannot be cloned.
Fixes: 6787927475 ("tipc: buffer overflow handling in listener socket")
Reported-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rhashtable_lookup_fast() internally calls rcu_read_lock() then,
calls rhashtable_lookup(). So if rcu_read_lock() is already held,
rhashtable_lookup() is enough.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
We introduce a feature that works like a combination of TCP_NAGLE and
TCP_CORK, but without some of the weaknesses of those. In particular,
we will not observe long delivery delays because of delayed acks, since
the algorithm itself decides if and when acks are to be sent from the
receiving peer.
- The nagle property as such is determined by manipulating a new
'maxnagle' field in struct tipc_sock. If certain conditions are met,
'maxnagle' will define max size of the messages which can be bundled.
If it is set to zero no messages are ever bundled, implying that the
nagle property is disabled.
- A socket with the nagle property enabled enters nagle mode when more
than 4 messages have been sent out without receiving any data message
from the peer.
- A socket leaves nagle mode whenever it receives a data message from
the peer.
In nagle mode, messages smaller than 'maxnagle' are accumulated in the
socket write queue. The last buffer in the queue is marked with a new
'ack_required' bit, which forces the receiving peer to send a CONN_ACK
message back to the sender upon reception.
The accumulated contents of the write queue is transmitted when one of
the following events or conditions occur.
- A CONN_ACK message is received from the peer.
- A data message is received from the peer.
- A SOCK_WAKEUP pseudo message is received from the link level.
- The write queue contains more than 64 1k blocks of data.
- The connection is being shut down.
- There is no CONN_ACK message to expect. I.e., there is currently
no outstanding message where the 'ack_required' bit was set. As a
consequence, the first message added after we enter nagle mode
is always sent directly with this bit set.
This new feature gives a 50-100% improvement of throughput for small
(i.e., less than MTU size) messages, while it might add up to one RTT
to latency time when the socket is in nagle mode.
Acked-by: Ying Xue <ying.xue@windreiver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, TIPC transports intra-node user data messages directly
socket to socket, hence shortcutting all the lower layers of the
communication stack. This gives TIPC very good intra node performance,
both regarding throughput and latency.
We now introduce a similar mechanism for TIPC data traffic across
network namespaces located in the same kernel. On the send path, the
call chain is as always accompanied by the sending node's network name
space pointer. However, once we have reliably established that the
receiving node is represented by a namespace on the same host, we just
replace the namespace pointer with the receiving node/namespace's
ditto, and follow the regular socket receive patch though the receiving
node. This technique gives us a throughput similar to the node internal
throughput, several times larger than if we let the traffic go though
the full network stacks. As a comparison, max throughput for 64k
messages is four times larger than TCP throughput for the same type of
traffic.
To meet any security concerns, the following should be noted.
- All nodes joining a cluster are supposed to have been be certified
and authenticated by mechanisms outside TIPC. This is no different for
nodes/namespaces on the same host; they have to auto discover each
other using the attached interfaces, and establish links which are
supervised via the regular link monitoring mechanism. Hence, a kernel
local node has no other way to join a cluster than any other node, and
have to obey to policies set in the IP or device layers of the stack.
- Only when a sender has established with 100% certainty that the peer
node is located in a kernel local namespace does it choose to let user
data messages, and only those, take the crossover path to the receiving
node/namespace.
- If the receiving node/namespace is removed, its namespace pointer
is invalidated at all peer nodes, and their neighbor link monitoring
will eventually note that this node is gone.
- To ensure the "100% certainty" criteria, and prevent any possible
spoofing, received discovery messages must contain a proof that the
sender knows a common secret. We use the hash mix of the sending
node/namespace for this purpose, since it can be accessed directly by
all other namespaces in the kernel. Upon reception of a discovery
message, the receiver checks this proof against all the local
namespaces'hash_mix:es. If it finds a match, that, along with a
matching node id and cluster id, this is deemed sufficient proof that
the peer node in question is in a local namespace, and a wormhole can
be opened.
- We should also consider that TIPC is intended to be a cluster local
IPC mechanism (just like e.g. UNIX sockets) rather than a network
protocol, and hence we think it can justified to allow it to shortcut the
lower protocol layers.
Regarding traceability, we should notice that since commit 6c9081a391
("tipc: add loopback device tracking") it is possible to follow the node
internal packet flow by just activating tcpdump on the loopback
interface. This will be true even for this mechanism; by activating
tcpdump on the involved nodes' loopback interfaces their inter-name
space messaging can easily be tracked.
v2:
- update 'net' pointer when node left/rejoined
v3:
- grab read/write lock when using node ref obj
v4:
- clone traffics between netns to loopback
Suggested-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many poll() handlers are lockless. Using skb_queue_empty_lockless()
instead of skb_queue_empty() is more appropriate.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk->sk_backlog.len can be written by BH handlers, and read
from process contexts in a lockless way.
Note the write side should also use WRITE_ONCE() or a variant.
We need some agreement about the best way to do this.
syzbot reported :
BUG: KCSAN: data-race in tcp_add_backlog / tcp_grow_window.isra.0
write to 0xffff88812665f32c of 4 bytes by interrupt on cpu 1:
sk_add_backlog include/net/sock.h:934 [inline]
tcp_add_backlog+0x4a0/0xcc0 net/ipv4/tcp_ipv4.c:1737
tcp_v4_rcv+0x1aba/0x1bf0 net/ipv4/tcp_ipv4.c:1925
ip_protocol_deliver_rcu+0x51/0x470 net/ipv4/ip_input.c:204
ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252
dst_input include/net/dst.h:442 [inline]
ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523
__netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5004
__netif_receive_skb+0x37/0xf0 net/core/dev.c:5118
netif_receive_skb_internal+0x59/0x190 net/core/dev.c:5208
napi_skb_finish net/core/dev.c:5671 [inline]
napi_gro_receive+0x28f/0x330 net/core/dev.c:5704
receive_buf+0x284/0x30b0 drivers/net/virtio_net.c:1061
virtnet_receive drivers/net/virtio_net.c:1323 [inline]
virtnet_poll+0x436/0x7d0 drivers/net/virtio_net.c:1428
napi_poll net/core/dev.c:6352 [inline]
net_rx_action+0x3ae/0xa50 net/core/dev.c:6418
read to 0xffff88812665f32c of 4 bytes by task 7292 on cpu 0:
tcp_space include/net/tcp.h:1373 [inline]
tcp_grow_window.isra.0+0x6b/0x480 net/ipv4/tcp_input.c:413
tcp_event_data_recv+0x68f/0x990 net/ipv4/tcp_input.c:717
tcp_rcv_established+0xbfe/0xf50 net/ipv4/tcp_input.c:5618
tcp_v4_do_rcv+0x381/0x4e0 net/ipv4/tcp_ipv4.c:1542
sk_backlog_rcv include/net/sock.h:945 [inline]
__release_sock+0x135/0x1e0 net/core/sock.c:2427
release_sock+0x61/0x160 net/core/sock.c:2943
tcp_recvmsg+0x63b/0x1a30 net/ipv4/tcp.c:2181
inet_recvmsg+0xbb/0x250 net/ipv4/af_inet.c:838
sock_recvmsg_nosec net/socket.c:871 [inline]
sock_recvmsg net/socket.c:889 [inline]
sock_recvmsg+0x92/0xb0 net/socket.c:885
sock_read_iter+0x15f/0x1e0 net/socket.c:967
call_read_iter include/linux/fs.h:1864 [inline]
new_sync_read+0x389/0x4f0 fs/read_write.c:414
__vfs_read+0xb1/0xc0 fs/read_write.c:427
vfs_read fs/read_write.c:461 [inline]
vfs_read+0x143/0x2c0 fs/read_write.c:446
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 7292 Comm: syz-fuzzer Not tainted 5.3.0+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
sk_add_backlog() callers usually read sk->sk_rcvbuf without
owning the socket lock. This means sk_rcvbuf value can
be changed by other cpus, and KCSAN complains.
Add READ_ONCE() annotations to document the lockless nature
of these reads.
Note that writes over sk_rcvbuf should also use WRITE_ONCE(),
but this will be done in separate patches to ease stable
backports (if we decide this is relevant for stable trees).
BUG: KCSAN: data-race in tcp_add_backlog / tcp_recvmsg
write to 0xffff88812ab369f8 of 8 bytes by interrupt on cpu 1:
__sk_add_backlog include/net/sock.h:902 [inline]
sk_add_backlog include/net/sock.h:933 [inline]
tcp_add_backlog+0x45a/0xcc0 net/ipv4/tcp_ipv4.c:1737
tcp_v4_rcv+0x1aba/0x1bf0 net/ipv4/tcp_ipv4.c:1925
ip_protocol_deliver_rcu+0x51/0x470 net/ipv4/ip_input.c:204
ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252
dst_input include/net/dst.h:442 [inline]
ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523
__netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5004
__netif_receive_skb+0x37/0xf0 net/core/dev.c:5118
netif_receive_skb_internal+0x59/0x190 net/core/dev.c:5208
napi_skb_finish net/core/dev.c:5671 [inline]
napi_gro_receive+0x28f/0x330 net/core/dev.c:5704
receive_buf+0x284/0x30b0 drivers/net/virtio_net.c:1061
virtnet_receive drivers/net/virtio_net.c:1323 [inline]
virtnet_poll+0x436/0x7d0 drivers/net/virtio_net.c:1428
napi_poll net/core/dev.c:6352 [inline]
net_rx_action+0x3ae/0xa50 net/core/dev.c:6418
read to 0xffff88812ab369f8 of 8 bytes by task 7271 on cpu 0:
tcp_recvmsg+0x470/0x1a30 net/ipv4/tcp.c:2047
inet_recvmsg+0xbb/0x250 net/ipv4/af_inet.c:838
sock_recvmsg_nosec net/socket.c:871 [inline]
sock_recvmsg net/socket.c:889 [inline]
sock_recvmsg+0x92/0xb0 net/socket.c:885
sock_read_iter+0x15f/0x1e0 net/socket.c:967
call_read_iter include/linux/fs.h:1864 [inline]
new_sync_read+0x389/0x4f0 fs/read_write.c:414
__vfs_read+0xb1/0xc0 fs/read_write.c:427
vfs_read fs/read_write.c:461 [inline]
vfs_read+0x143/0x2c0 fs/read_write.c:446
ksys_read+0xd5/0x1b0 fs/read_write.c:587
__do_sys_read fs/read_write.c:597 [inline]
__se_sys_read fs/read_write.c:595 [inline]
__x64_sys_read+0x4c/0x60 fs/read_write.c:595
do_syscall_64+0xcf/0x2f0 arch/x86/entry/common.c:296
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 7271 Comm: syz-fuzzer Not tainted 5.3.0+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Benefit from the fact that the generic netlink code can parse the attrs
for dumpit op and avoid need to parse it in the op callback.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The policy for handling the skb list locks on the send and receive paths
is simple.
- On the send path we never need to grab the lock on the 'xmitq' list
when the destination is an exernal node.
- On the receive path we always need to grab the lock on the 'inputq'
list, irrespective of source node.
However, when transmitting node local messages those will eventually
end up on the receive path of a local socket, meaning that the argument
'xmitq' in tipc_node_xmit() will become the 'ínputq' argument in the
function tipc_sk_rcv(). This has been handled by always initializing
the spinlock of the 'xmitq' list at message creation, just in case it
may end up on the receive path later, and despite knowing that the lock
in most cases never will be used.
This approach is inaccurate and confusing, and has also concealed the
fact that the stated 'no lock grabbing' policy for the send path is
violated in some cases.
We now clean up this by never initializing the lock at message creation,
instead doing this at the moment we find that the message actually will
enter the receive path. At the same time we fix the four locations
where we incorrectly access the spinlock on the send/error path.
This patch also reverts commit d12cffe932 ("tipc: ensure head->lock
is initialised") which has now become redundant.
CC: Eric Dumazet <edumazet@google.com>
Reported-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 517d7c79bd ("tipc: fix hanging poll() for stream sockets")
introduced a regression for clients using non-blocking sockets.
After the commit, we send EPOLLOUT event to the client even in
TIPC_CONNECTING state. This causes the subsequent send() to fail
with ENOTCONN, as the socket is still not in TIPC_ESTABLISHED state.
In this commit, we:
- improve the fix for hanging poll() by replacing sk_data_ready()
with sk_state_change() to wake up all clients.
- revert the faulty updates introduced by commit 517d7c79bd
("tipc: fix hanging poll() for stream sockets").
Fixes: 517d7c79bd ("tipc: fix hanging poll() for stream sockets")
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently have two levels of strict validation:
1) liberal (default)
- undefined (type >= max) & NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
- garbage at end of message accepted
2) strict (opt-in)
- NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
Split out parsing strictness into four different options:
* TRAILING - check that there's no trailing data after parsing
attributes (in message or nested)
* MAXTYPE - reject attrs > max known type
* UNSPEC - reject attributes with NLA_UNSPEC policy entries
* STRICT_ATTRS - strictly validate attribute size
The default for future things should be *everything*.
The current *_strict() is a combination of TRAILING and MAXTYPE,
and is renamed to _deprecated_strict().
The current regular parsing has none of this, and is renamed to
*_parse_deprecated().
Additionally it allows us to selectively set one of the new flags
even on old policies. Notably, the UNSPEC flag could be useful in
this case, since it can be arranged (by filling in the policy) to
not be an incompatible userspace ABI change, but would then going
forward prevent forgetting attribute entries. Similar can apply
to the POLICY flag.
We end up with the following renames:
* nla_parse -> nla_parse_deprecated
* nla_parse_strict -> nla_parse_deprecated_strict
* nlmsg_parse -> nlmsg_parse_deprecated
* nlmsg_parse_strict -> nlmsg_parse_deprecated_strict
* nla_parse_nested -> nla_parse_nested_deprecated
* nla_validate_nested -> nla_validate_nested_deprecated
Using spatch, of course:
@@
expression TB, MAX, HEAD, LEN, POL, EXT;
@@
-nla_parse(TB, MAX, HEAD, LEN, POL, EXT)
+nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression TB, MAX, NLA, POL, EXT;
@@
-nla_parse_nested(TB, MAX, NLA, POL, EXT)
+nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT)
@@
expression START, MAX, POL, EXT;
@@
-nla_validate_nested(START, MAX, POL, EXT)
+nla_validate_nested_deprecated(START, MAX, POL, EXT)
@@
expression NLH, HDRLEN, MAX, POL, EXT;
@@
-nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT)
+nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT)
For this patch, don't actually add the strict, non-renamed versions
yet so that it breaks compile if I get it wrong.
Also, while at it, make nla_validate and nla_parse go down to a
common __nla_validate_parse() function to avoid code duplication.
Ultimately, this allows us to have very strict validation for every
new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the
next patch, while existing things will continue to work as is.
In effect then, this adds fully strict validation for any new command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if the NLA_F_NESTED flag was introduced more than 11 years ago, most
netlink based interfaces (including recently added ones) are still not
setting it in kernel generated messages. Without the flag, message parsers
not aware of attribute semantics (e.g. wireshark dissector or libmnl's
mnl_nlmsg_fprintf()) cannot recognize nested attributes and won't display
the structure of their contents.
Unfortunately we cannot just add the flag everywhere as there may be
userspace applications which check nlattr::nla_type directly rather than
through a helper masking out the flags. Therefore the patch renames
nla_nest_start() to nla_nest_start_noflag() and introduces nla_nest_start()
as a wrapper adding NLA_F_NESTED. The calls which add NLA_F_NESTED manually
are rewritten to use nla_nest_start().
Except for changes in include/net/netlink.h, the patch was generated using
this semantic patch:
@@ expression E1, E2; @@
-nla_nest_start(E1, E2)
+nla_nest_start_noflag(E1, E2)
@@ expression E1, E2; @@
-nla_nest_start_noflag(E1, E2 | NLA_F_NESTED)
+nla_nest_start(E1, E2)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using TIPC_SOCK_RECVQ_DEPTH for getsockopt(), it returns the
number of buffers in receive socket buffer which is not so helpful
for user space applications.
This commit introduces the new option TIPC_SOCK_RECVQ_USED which
returns the current allocated bytes of the receive socket buffer.
This helps user space applications dimension its buffer usage to
avoid buffer overload issue.
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb free-ed in:
1/ condition 1: tipc_sk_filter_rcv -> tipc_sk_proto_rcv
2/ condition 2: tipc_sk_filter_rcv -> tipc_group_filter_msg
This leads to a "use-after-free" access in the next condition.
We fix this by intializing the variable at declaration, then it is safe
to check this variable to continue processing if condition matches.
syzbot report:
==================================================================
BUG: KASAN: use-after-free in tipc_sk_filter_rcv+0x2166/0x34f0
net/tipc/socket.c:2167
Read of size 4 at addr ffff88808ea58534 by task kworker/u4:0/7
CPU: 0 PID: 7 Comm: kworker/u4:0 Not tainted 5.0.0+ #61
Hardware name: Google Google Compute Engine/Google Compute Engine,
BIOS Google 01/01/2011
Workqueue: tipc_send tipc_conn_send_work
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
print_address_description.cold+0x7c/0x20d mm/kasan/report.c:187
kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317
__asan_report_load4_noabort+0x14/0x20 mm/kasan/generic_report.c:131
tipc_sk_filter_rcv+0x2166/0x34f0 net/tipc/socket.c:2167
tipc_sk_enqueue net/tipc/socket.c:2254 [inline]
tipc_sk_rcv+0xc45/0x25a0 net/tipc/socket.c:2305
tipc_topsrv_kern_evt+0x3b7/0x580 net/tipc/topsrv.c:610
tipc_conn_send_to_sock+0x43e/0x5f0 net/tipc/topsrv.c:283
tipc_conn_send_work+0x65/0x80 net/tipc/topsrv.c:303
process_one_work+0x98e/0x1790 kernel/workqueue.c:2269
worker_thread+0x98/0xe40 kernel/workqueue.c:2415
kthread+0x357/0x430 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
Reported-by: syzbot+e863893591cc7a622e40@syzkaller.appspotmail.com
Fixes: c55c8eda ("tipc: smooth change between replicast and broadcast")
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, a multicast stream may start out using replicast, because
there are few destinations, and then it should ideally switch to
L2/broadcast IGMP/multicast when the number of destinations grows beyond
a certain limit. The opposite should happen when the number decreases
below the limit.
To eliminate the risk of message reordering caused by method change,
a sending socket must stick to a previously selected method until it
enters an idle period of 5 seconds. Means there is a 5 seconds pause
in the traffic from the sender socket.
If the sender never makes such a pause, the method will never change,
and transmission may become very inefficient as the cluster grows.
With this commit, we allow such a switch between replicast and
broadcast without any need for a traffic pause.
Solution is to send a dummy message with only the header, also with
the SYN bit set, via broadcast or replicast. For the data message,
the SYN bit is set and sending via replicast or broadcast (inverse
method with dummy).
Then, at receiving side any messages follow first SYN bit message
(data or dummy message), they will be held in deferred queue until
another pair (dummy or data message) arrived in other link.
v2: reverse christmas tree declaration
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We move the check that prevents connecting service ranges to after
the RDM/DGRAM check, and move address sanity control to a separate
function that also validates the service range.
Fixes: 23998835be ("tipc: improve address sanity check in tipc_connect()")
Signed-off-by: Erik Hugne <erik.hugne@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nla_nest_start may fail. The fix check its status and returns
-EMSGSIZE in case it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix regression bug introduced in
commit 365ad353c2 ("tipc: reduce risk of user starvation during link
congestion")
Only signal -EDESTADDRREQ for RDM/DGRAM if we don't have a cached
sockaddr.
Fixes: 365ad353c2 ("tipc: reduce risk of user starvation during link congestion")
Signed-off-by: Erik Hugne <erik.hugne@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending multicast messages via blocking socket,
if sending link is congested (tsk->cong_link_cnt is set to 1),
the sending thread will be put into sleeping state. However,
tipc_sk_filter_rcv() is called under socket spin lock but
tipc_wait_for_cond() is not. So, there is no guarantee that
the setting of tsk->cong_link_cnt to 0 in tipc_sk_proto_rcv() in
CPU-1 will be perceived by CPU-0. If that is the case, the sending
thread in CPU-0 after being waken up, will continue to see
tsk->cong_link_cnt as 1 and put the sending thread into sleeping
state again. The sending thread will sleep forever.
CPU-0 | CPU-1
tipc_wait_for_cond() |
{ |
// condition_ = !tsk->cong_link_cnt |
while ((rc_ = !(condition_))) { |
... |
release_sock(sk_); |
wait_woken(); |
| if (!sock_owned_by_user(sk))
| tipc_sk_filter_rcv()
| {
| ...
| tipc_sk_proto_rcv()
| {
| ...
| tsk->cong_link_cnt--;
| ...
| sk->sk_write_space(sk);
| ...
| }
| ...
| }
sched_annotate_sleep(); |
lock_sock(sk_); |
remove_wait_queue(); |
} |
} |
This commit fixes it by adding memory barrier to tipc_sk_proto_rcv()
and tipc_wait_for_cond().
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit replaces schedule_timeout() with wait_woken()
in function tipc_wait_for_rcvmsg(). wait_woken() uses
memory barriers in its implementation to avoid potential
race condition when putting a process into sleeping state
and then waking it up.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 844cf763fb ("tipc: make macro tipc_wait_for_cond() smp safe")
replaced finish_wait() with remove_wait_queue() but still used
prepare_to_wait(). This causes unnecessary conditional
checking before adding to wait queue in prepare_to_wait().
This commit replaces prepare_to_wait() with add_wait_queue()
as the pair function with remove_wait_queue().
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warnings:
net/tipc/link.c:1125:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
net/tipc/socket.c:736:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
net/tipc/socket.c:2418:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski