Current code set platform drvdata to dspi. However, the code in dspi_suspend()
and dspi_resume() assumes the drvdata is the address of master.
Fix it by setting platform drvdata to master.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Amend the spi atmel pin controller to optionally take a pin control
handle and set the state of the pins to:
- "default" on boot, resume and before performing an spitransfer
- "sleep" on suspend()
This should make it possible to optimize energy usage for the pins
both for the suspend/resume cycle
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Zero length transfer becomes invalid since
"spi: core: Validate length of the transfers in message" commit,
but it should be valid to support an odd device, for example, which
requires long delay between chipselect and the first transfer, etc.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In the implementation of __spi_validate(), spi core will set transfer
bits_per_word and max speed as spi device default if it is not set for
this transfer. So we can remove the same logic in spi_xcomm_setup_transfer().
Also remove a redundant code to initialize is_first variable.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This controller only supports 8 bits word length.
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This controller only supports 8 bits word length.
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The 'ath79_spi_setup_cs' function initializes the chip
select line of a given SPI device in order to make sure
that the device is inactive.
If the SPI_CS_HIGH bit is set for a given device, it
means that the CS line of that device is active HIGH
so it must be set to LOW initially. In case of GPIO
CS lines, the 'ath79_spi_setup_cs' function does the
opposite of that due to the wrong GPIO flags.
Fix the code to use the correct GPIO flags.
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Set master->max_speed_hz then spi core will handle checking transfer speed.
So we can remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
spi core will handle validating transfer length since commit 4d94bd21b3
"spi: core: Validate length of the transfers in message".
So remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set master->max_speed_hz then spi core will handle checking transfer speed.
The behavior is different from current code when the speed_hz is greater than
the maximum transfer speed supported by the controller.
Unless there is other good reason, I think we had better make the behavior
consistent with what spi core does.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code uses struct octeon_spi_setup to store max_speed_hz, chip_select and
mode settings of current spi device.
We can always get the same settings in octeon_spi_do_transfer() by msg->spi.
So this patch removes struct octeon_spi_setup and octeon_spi_setup,
octeon_spi_cleanup functions.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
there are many SPI clients which use the following protocal:
step 1: send command bytes to clients(rx buffer is empty)
step 2: send data bytes to clients or receive data bytes from
clients.
SiRFprimaII provides a shortcut for this kind of SPI transfer.
when tx buf is less or equal than 4 bytes and rx buf is null
in a transfer, we think it as 'command' data and use hardware
command register for the transfer.
here we can save some CPU loading than doing both tx and rx
for a normal transfer.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In the implementation of __spi_validate(), spi core will set transfer
bits_per_word and max speed as spi device default if it is not set for
this transfer. So we can remove the same implementation in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
In the implementation of __spi_validate(), spi core will use spi device's max
speed as default transfer speed if it is not set for this transfer.
So we can remove the same logic in hspi_hw_setup().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
spi core will handle validating transfer length since commit 4d94bd21b3
"spi: core: Validate length of the transfers in message".
So remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
spi core will handle validating transfer length since commit 4d94bd21b3
"spi: core: Validate length of the transfers in message".
So remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_ioremap_resource() in order to make the code simpler,
and remove redundant return value check of platform_get_resource()
because the value is checked by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently, at module removal, one gets the following warnings:
------------[ cut here ]------------
WARNING: at drivers/clk/clk.c:780 clk_disable+0x18/0x24()
Modules linked in: spi_imx(-) [last unloaded: ev76c560]
CPU: 1 PID: 16337 Comm: rmmod Tainted: G W 3.10.17-80548-g90191eb-dirty #33
[<80013b4c>] (unwind_backtrace+0x0/0xf8) from [<800115dc>] (show_stack+0x10/0x14)
[<800115dc>] (show_stack+0x10/0x14) from [<800257b8>] (warn_slowpath_common+0x4c/0x68)
[<800257b8>] (warn_slowpath_common+0x4c/0x68) from [<800257f0>] (warn_slowpath_null+0x1c/0x24)
[<800257f0>] (warn_slowpath_null+0x1c/0x24) from [<803f60ec>] (clk_disable+0x18/0x24)
[<803f60ec>] (clk_disable+0x18/0x24) from [<7f02c9cc>] (spi_imx_remove+0x54/0x9c [spi_imx])
[<7f02c9cc>] (spi_imx_remove+0x54/0x9c [spi_imx]) from [<8025868c>] (platform_drv_remove+0x18/0x1c)
[<8025868c>] (platform_drv_remove+0x18/0x1c) from [<80256f60>] (__device_release_driver+0x70/0xcc)
[<80256f60>] (__device_release_driver+0x70/0xcc) from [<80257770>] (driver_detach+0xcc/0xd0)
[<80257770>] (driver_detach+0xcc/0xd0) from [<80256d90>] (bus_remove_driver+0x7c/0xc0)
[<80256d90>] (bus_remove_driver+0x7c/0xc0) from [<80068668>] (SyS_delete_module+0x144/0x1f8)
[<80068668>] (SyS_delete_module+0x144/0x1f8) from [<8000e080>] (ret_fast_syscall+0x0/0x30)
---[ end trace 1f5df9ad54996300 ]---
------------[ cut here ]------------
WARNING: at drivers/clk/clk.c:780 clk_disable+0x18/0x24()
Modules linked in: spi_imx(-) [last unloaded: ev76c560]
CPU: 1 PID: 16337 Comm: rmmod Tainted: G W 3.10.17-80548-g90191eb-dirty #33
[<80013b4c>] (unwind_backtrace+0x0/0xf8) from [<800115dc>] (show_stack+0x10/0x14)
[<800115dc>] (show_stack+0x10/0x14) from [<800257b8>] (warn_slowpath_common+0x4c/0x68)
[<800257b8>] (warn_slowpath_common+0x4c/0x68) from [<800257f0>] (warn_slowpath_null+0x1c/0x24)
[<800257f0>] (warn_slowpath_null+0x1c/0x24) from [<803f60ec>] (clk_disable+0x18/0x24)
[<803f60ec>] (clk_disable+0x18/0x24) from [<7f02c9e8>] (spi_imx_remove+0x70/0x9c [spi_imx])
[<7f02c9e8>] (spi_imx_remove+0x70/0x9c [spi_imx]) from [<8025868c>] (platform_drv_remove+0x18/0x1c)
[<8025868c>] (platform_drv_remove+0x18/0x1c) from [<80256f60>] (__device_release_driver+0x70/0xcc)
[<80256f60>] (__device_release_driver+0x70/0xcc) from [<80257770>] (driver_detach+0xcc/0xd0)
[<80257770>] (driver_detach+0xcc/0xd0) from [<80256d90>] (bus_remove_driver+0x7c/0xc0)
[<80256d90>] (bus_remove_driver+0x7c/0xc0) from [<80068668>] (SyS_delete_module+0x144/0x1f8)
[<80068668>] (SyS_delete_module+0x144/0x1f8) from [<8000e080>] (ret_fast_syscall+0x0/0x30)
---[ end trace 1f5df9ad54996301 ]---
Since commit 9e556dcc55, "spi: spi-imx: only
enable the clocks when we start to transfer a message", clocks are always
disabled except when transmitting messages. There is thus no need to
disable them at module removal.
Fixes: 9e556dcc55 (spi: spi-imx: only enable the clocks when we start to transfer a message)
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
hspi_cleanup() is doing nothing except print a non-useful debug message,
so remove it. Also remove unused hspi2info macro.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The only remaining feature of spi-bitbang used by this driver is the
chipselect() callback, which just does conditional GPIO.
This is handled fine by the SPI core's spi_set_cs(), hence switch the
driver to use the core message handling through our own transfer_one()
method.
As the (optional) GPIO CS is no longer deasserted at spi_master.setup()
time (through spi_bitbang_setup() and the spi_bitbang.chipselect()
callback), we now have to take care of that ourselves.
Remove the call to spi_master_put() in sh_msiof_spi_remove(), as our SPI
master is now registered using devm_spi_register_master()
(spi_bitbang_start() uses the non-managed version).
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set bits_per_word_mask so the spi core will reject transfers that attempt
to use an unsupported bits_per_word value.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move clock management and pin configuration from the bitbang chipselect()
method to the SPI core prepare_message() and unprepare_message() methods.
As spi_master.{,un}prepare_message() is guaranteed to be called in
matching pairs, the clock management synchronization is no longer needed.
As sh_msiof_spi_set_pin_regs() is no longer called at spi_master.setup()
time (through spi_bitbang_setup() and the spi_bitbang.chipselect()
callback), we now have to take care of that ourselves.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for the MSIOF variant in the R-Car H2 (r8a7790) and M2
(r8a7791) SoCs.
Binding documentation:
- Add future-proof "renesas,msiof-<soctype>" compatible values,
- The default for "renesas,rx-fifo-size" is 256 on R-Car H2 and M2,
- "renesas,tx-fifo-size" and "renesas,rx-fifo-size" are deprecated for
soctype-specific bindings,
- Add example bindings.
Implementation:
- MSIOF on R-Car H2 and M2 requires the transmission of dummy data if
data is being received only (cfr. "Set SICTR.TSCKE to 1" and "Write
dummy transmission data to SITFDR" in paragraph "Transmit and Receive
Procedures" of the Hardware User's Manual).
- As RX depends on TX, MSIOF on R-Car H2 and M2 also lacks the RSCR
register (Receive Clock Select Register), and some bits in the RMDR1
(Receive Mode Register 1) and TMDR2 (Transmit Mode Register 2)
registers.
- Use the recently introduced SPI_MASTER_MUST_TX flag to enable support
for dummy transmission in the SPI core, and to differentiate from other
MSIOF implementations in code paths that need this.
- New DT compatible values ("renesas,msiof-r8a7790" and
"renesas,msiof-r8a7791") are added, as well as new platform device
names ("spi_r8a7790_msiof" and "spi_r8a7791_msiof").
- The default RX FIFO size is 256 words on R-Car H2 and M2.
This is loosely based on a set of patches from Takashi Yoshii
<takasi-y@ops.dti.ne.jp>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
As different variants of MSIOF have different FIFO sizes, move the default
FIFO sizes to a new struct sh_msiof_chipdata, pointed to from the device
ID data.
[Moved ifdef to fix build -- broonie]
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
Documentation:
- Add missing "interrupt-parent", "#address-cells", "#size-cells", and
"clocks" properties,
- Add missing default values for "num-cs", "renesas,tx-fifo-size" and
"renesas,rx-fifo-size",
- Add a reference to the pinctrl documentation.
Implementation:
- As "num-cs" is marked optional, provide a sensible default.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for Dual/Quad SPI Transfers to the spidev API.
As this uses SPI mode bits that don't fit in a single byte, two new
ioctls (SPI_IOC_RD_MODE32 and SPI_IOC_WR_MODE32) are introduced.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
In commit f477b7fb13 ("spi: DUAL and QUAD
support"), spi_device.mode was enlarged from 8 to 16 bits.
However, the spidev code still only saved 8 bits of data. If a spidev
SPI_IOC_WR_MODE or SPI_IOC_WR_LSB_FIRST request failed, only the lower 8
bits of the SPI mode were restored, inadvertently clearing the upper 8
bits, possibly disabling Quad or Dual SPI transfers for the device.
Save up to 32 bits to fix this.
For SPI_IOC_WR_MODE this is probably not so important, as it doesn't allow
setting Quad or Dual mode anyway, but SPI_IOC_WR_LSB_FIRST is used to just
set or clear a single bit.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use SIMPLE_DEV_PM_OPS macro in order to make the code simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove unnecessary space in order to fix the following
checkpatch issues.
WARNING: Unnecessary space after function pointer name
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Mark Brown <broonie@linaro.org>
If during registering SPI master due to SPI device probing a SPI transfer
is issued the DMA buffers are not allocated yet.
This fixes the following oops:
pch_spi 0000:02:0c.1: enabling device (0000 -> 0002)
pch_spi 0000:02:0c.1: master is unqueued, this is deprecated
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<c125aa05>] pch_spi_handle_dma+0x15c/0x6f4
[...]
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code uses struct spi_qup_device to store spi->mode and spi->chip_select
settings. We can get these settings in spi_qup_transfer_one and spi_qup_set_cs
without using struct spi_qup_device. Refactor the code a bit to remove
spi_qup_setup(), spi_qup_cleanup(), and struct spi_qup_device.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
spi core will handle validating transfer length since commit 4d94bd21b3
"spi: core: Validate length of the transfers in message".
So remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The module version is unlikely to be updated, use kernel version should be
enough.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver uses writel_relaxed() which does not exist in x86, ppc, etc.
Make it depend on ARM && COMPILE_TEST to avoid below build error:
CC [M] drivers/spi/spi-qup.o
drivers/spi/spi-qup.c: In function 'spi_qup_set_state':
drivers/spi/spi-qup.c:180:3: error: implicit declaration of function 'writel_relaxed' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[2]: *** [drivers/spi/spi-qup.o] Error 1
make[1]: *** [drivers/spi] Error 2
make: *** [drivers] Error 2
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
use SET_SYSTEM_SLEEP_PM_OPS to initialize PM entries, this makes the codes
clean and also enable the ability of hibernation support for sirf SPI.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
sirf-dma driver enabled generic dt binding for dma channels.
see here we remove self-defined dma channel prop and move to
use generic dma_request_slave_channel.
related changes in dts is something like:
dmas = <&dmac1 9>,
<&dmac1 4>;
dma-names = "rx", "tx";
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix below build error when CONFIG_PM_RUNTIME=y:
C [M] drivers/spi/spi-qup.o
drivers/spi/spi-qup.c: In function 'spi_qup_pm_suspend_runtime':
drivers/spi/spi-qup.c:712:12: error: 'QUP_CLOCK_AUTO_GATE' undeclared (first use in this function)
drivers/spi/spi-qup.c:712:12: note: each undeclared identifier is reported only once for each function it appears in
drivers/spi/spi-qup.c: In function 'spi_qup_pm_resume_runtime':
drivers/spi/spi-qup.c:725:13: error: 'QUP_CLOCK_AUTO_GATE' undeclared (first use in this function)
make[2]: *** [drivers/spi/spi-qup.o] Error 1
make[1]: *** [drivers/spi] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fixes below checkpatch warning:
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(10);
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
fsl_spi_grlib_probe() may update mpc8xxx_spi->max_bits_per_word setting.
So set master->bits_per_word_mask after fsl_spi_grlib_probe().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
spi_bitbang requires custom setup_transfer() to be defined if there is a
custom txrx_bufs(). Thus keep the empty xilinx_spi_setup_transfer() function
in the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set master->max_speed_hz then spi core will handle checking transfer speed.
So we can remove the same checking in this driver.
Also remove checking spi->chip_select in spi_qup_setup(), the checking is done
by spi core.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver uses devm_spi_register_master() so don't explicitly call
spi_master_put() in spi_qup_remove().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
While normal Dual and Quad SPI Transfers are unidirectional, we must do
a bidirectional transfer if loopback mode is enabled, else rx_buf is not
filled.
With spidev it seemed to work, as spidev uses the same buffer for
tranmission and reception.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
If spi_master.cleanup() is not needed, it can be left unimplemented.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The older Allwinner SoCs (A10, A13, A10s and A20) all have the same SPI
controller.
Unfortunately, this SPI controller, even though quite similar, is significantly
different from the recently supported A31 SPI controller (different registers
offset, split/merged registers, etc.). Supporting both controllers in a single
driver would be unreasonable, hence the addition of a new driver.
Like its more recent counterpart, it supports DMA, but the driver only does PIO
until we have a dmaengine driver for this platform.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SPI_IMX is selected by imx_v6_v7_defconfig/imx_v4_v5_defconfig and we don't need
to have a default setting which depends on the IMX_HAVE_PLATFORM_SPI_IMX symbol.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In current implementation, CS is controlled by GPIO, which is passed
through spi->controller_data. However, the MSIOF HW module has a function
to output CS by itself, which is already enabled and actual switch will be
done by pinmux.
Store the GPIO number in the core cs_gpio field, and ignore it if it is
an invalid (negative) GPIO number.
Loosely based on a patch from Takashi Yoshii <takasi-y@ops.dti.ne.jp>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Both spi_transfer.speed_hz and spi_master.max_speed_hz are u32
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
DT doesn't instantiate SPI children if spi_master.dev.of_node is not set up
properly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
SPI transfer length should be multiple of SPI word size,
where SPI word size should be power-of-two multiple
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Convert to use default implementation of transfer_one_message() which provides
standard handling of delays and chip select management.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
Qualcomm Universal Peripheral (QUP) core is an AHB slave that
provides a common data path (an output FIFO and an input FIFO)
for serial peripheral interface (SPI) mini-core. SPI in master
mode supports up to 50MHz, up to four chip selects, programmable
data path from 4 bits to 32 bits and numerous protocol variants.
Cc: Alok Chauhan <alokc@codeaurora.org>
Cc: Gilad Avidov <gavidov@codeaurora.org>
Cc: Kiran Gunda <kgunda@codeaurora.org>
Cc: Sagar Dharia <sdharia@codeaurora.org>
Cc: dsneddon@codeaurora.org
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
bus_num might be asigned dynamically to e.g. 32766. In this case the
calculated DMA channel based on SPI bus number is bogus. Use SPI channel
number instead for calculation.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set master->max_speed_hz and master->min_speed_hz then spi core will handle
checking transfer speed. So we can remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For DT case, spi core will call of_alias_get_id() and set master->bus_num if it
was not set.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The purpose of commit 1e8a52e18c
"spi: By default setup spi_masters with 1 chipselect and dynamics bus number"
is to avoid setting default value for bus_num and num_chipselect in spi master
drivers. So let's remove the duplicate code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-By: David Daney <david.daney@cavium.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove some coding sytle not in standard in former code.
Signed-off-by: Chao Fu <b44548@freescale.com>
Reviewed-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Freescale DSPI module will have two endianess in different platform,
but ARM is little endian. So when DSPI in big endian, core in little endian,
readl and writel can not adjust R/W register in this condition.
This patch will remove general readl/writel, and import regmap mechanism.
Data endian will be transfered in regmap APIs.
Documents: dspi add bool "big-endian" in dts node if DSPI module
work in big endian.
Signed-off-by: Chao Fu <b44548@freescale.com>
Reviewed-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code in sun6i_spi_set_cs() actually clears CPHA and CPOL bits which is
obvious wrong. The define for SUN6I_TFR_CTL_CS_MASK is wrong. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
No need to return a 'fake' return value on platform_get_irq() failure.
Just return the error code itself instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
No need to return a 'fake' return value on platform_get_irq() failure.
Just return the error code itself instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
By setting master->max_speed_hz and master->min_speed_hz, spi core will handle
checking transfer speed. So we can remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set "master->max_speed_hz = PCH_MAX_BAUDRATE" then we can remove pch_spi_setup.
In additional, pspi->max_speed_hz will never be 0 because it's default value
will be set to master->max_speed_hz.
Also remove list_empty checking in pch_spi_transfer() because the checking is
done by spi core.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
By setting master->max_speed_hz and master->min_speed_hz, spi core will handle
checking transfer speed. So we can remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Mark Brown <broonie@linaro.org>
This checking is already done in the implementation of spi_setup().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
While backporting 33cf00e5 ("spi: attach/detach SPI device to the ACPI
power domain"), I noticed that the code changes were suboptimal:
* Why use &spi->dev when we have dev at hand?
* After fixing the above, spi is used only once, so we don't really
need a local variable for it.
This results in the following clean-up.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In spi_add_device(), we have the code to validate spi->chip_select.
So remove the duplicate code in various drivers.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
So it will be checked when spi device is added onto the spi bus.
spi_add_device() calls spi_setup() which then calls spi->master->setup().
No need to check it every time sc18is602_transfer_one() is called.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use master->max_speed_hz instead of tspi->spi_max_frequency, so spi core will
handle checking transfer speed.
In additional, since commit 052eb2d490 'spi: core: Set max_speed_hz of
spi_device default to max_speed_hz of controller',
spi core will also set default spi->max_speed_hz if it is not set.
So remove the duplicate code in tegra_slink_setup.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use master->max_speed_hz instead of tspi->spi_max_frequency, so spi core will
handle checking transfer speed.
In additional, since commit 052eb2d490 'spi: core: Set max_speed_hz of
spi_device default to max_speed_hz of controller',
spi core will also set default spi->max_speed_hz if it is not set.
So remove tegra_sflash_setup().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use master->max_speed_hz instead of tspi->spi_max_frequency, so spi core will
handle checking transfer speed.
In additional, since commit 052eb2d490 'spi: core: Set max_speed_hz of
spi_device default to max_speed_hz of controller',
spi core will also set default spi->max_speed_hz if it is not set.
So remove the duplicate code in tegra_spi_setup.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
By setting master->max_speed_hz and master->min_speed_hz, spi core will handle
checking transfer speed. Then we can remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Mark Brown <broonie@linaro.org>
In __spi_validate(), xfer->speed_hz is set to be spi->max_speed_hz if it is not
set for this transfer. However, if spi->max_speed_hz is also not set,
xfer->speed_hz is 0. Some drivers (e.g. au1550, tegra114, tegra20-sflash,
tegra20-slink, etc.) then use below code to avoid setting xfer->speed_hz to 0.
/* Set speed to the spi max fequency if spi device has not set */
spi->max_speed_hz = spi->max_speed_hz ? : tspi->spi_max_frequency;
Let's handle it in spi core.
If spi->max_speed_hz is not set, make it default to spi->master->max_speed_hz.
So In __spi_validate() if both xfer->speed_hz and spi->max_speed_hz are not set,
xfer->speed_hz will be set to spi->master->max_speed_hz.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 0079aae0f1 ("spi: omap2: Add build dependencies for
writel_relaxed()") added an optional Kconfig dependency on SH. That
Kconfig symbol doesn't exist. Apparently SUPERH was intended. Use that.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Calling init_completion() once is enough.
For the rest of the iterations, call reinit_completion() instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove unused devdata pointer 'spi100k' in function omap1_spi100k_txrx_pio().
Detected by Coverity: CID 1077869.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove functions that only had an effect when using S3C_DMA and inline
dmaengine_terminate_all() since it's pointless to have a function which
expands to a single function call.
Signed-off-by: Mark Brown <broonie@linaro.org>
All the platforms which use the old S3C_DMA API have now been converted to
dmaengine so we can remove the legacy code from the driver, simplifying
maintenance.
Signed-off-by: Mark Brown <broonie@linaro.org>
When using dmaengine allow the core to do the DMA mapping. We still need
local mapping code for the non-dmaengine case so this doesn't save us
anything for now.
Signed-off-by: Mark Brown <broonie@linaro.org>
We don't modify the list entry while iterating the transfer list.
So use list_for_each_entry instead of list_for_each_entry_safe.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit a2fd4f9fa3 'spi: Support transfer speed checking in the core',
the SPI core validates the desired speed of a given transfer against the
minimum and maximum speeds supported by the controller.
So we can remove the same code in this driver and let spi core handle checking
the desired speed of a given transfer.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove unused devdata pointer 'orion_spi' in function orion_spi_write_read().
Detected by Coverity: CID 1077860.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Mark Brown <broonie@linaro.org>
It's pointless to use of_match_ptr within CONFIG_OF guard.
Use of_match_ptr around davinci_spi_of_match when setting .of_match_table.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
spi_master_get_devdata() never returns NULL when spi_alloc_master() success,
so remove NULL test for dspi.
We have ensured master is not NULL before assigning it to dspi->bitbang.master.
So also remove NULL test for dspi->bitbang.master.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Allwinner A31 has a new SPI controller IP compared to the older Allwinner
SoCs.
It supports DMA, but the driver only does PIO for now, and DMA will be
supported eventually.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Otherwise, spi_setup() fails with unsupported mode bits message.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
We cannot unconditionally use dma_map_single() to map data for use with
SPI since transfers may exceed a page and virtual addresses may not be
provided with physically contiguous pages. Further, addresses allocated
using vmalloc() need to be mapped differently to other addresses.
Currently only the MXS driver handles all this, a few drivers do handle
the possibility that buffers may not be physically contiguous which is
the main potential problem but many don't even do that. Factoring this
out into the core will make it easier for drivers to do a good job so if
the driver is using the core DMA code then generate a scatterlist
instead of mapping to a single address so do that.
This code is mainly based on a combination of the existing code in the MXS
and PXA2xx drivers. In future we should be able to extend it to allow the
core to concatenate adjacent transfers if they are compatible, improving
performance.
Currently for simplicity clients are not allowed to use the scatterlist
when they do DMA mapping, in the future the existing single address
mappings will be replaced with use of the scatterlist most likely as
part of pre-verifying transfers.
This change makes it mandatory to use scatterlists when using the core DMA
mapping so update the s3c64xx driver to do this when used with dmaengine.
Doing so makes the code more ugly but it is expected that the old s3c-dma
code can be removed very soon.
Signed-off-by: Mark Brown <broonie@linaro.org>
It is fairly common for SPI devices to require that one or both transfer
directions is always active. Currently drivers open code this in various
ways with varying degrees of efficiency. Start factoring this out by
providing flags SPI_MASTER_MUST_TX and SPI_MASTER_MUST_RX. These will cause
the core to provide buffers for the requested direction if none are
specified in the underlying transfer.
Currently this is fairly inefficient since we actually allocate a data
buffer which may get large, support for mapping transfers using a
scatterlist will allow us to avoid this for DMA based transfers.
Signed-off-by: Mark Brown <broonie@linaro.org>
As of commit 5ce0ba8865 ("spi: rcar: add
Renesas QSPI support on RSPI") the rspi driver handles Renesas QSPI, too,
but this was not reflected in the Kconfig help text.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver core is now taking care of putting our pins into default
state at probe. Thus we can remove the redundant call for it in probe.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make use of clk_prepare_enable and clk_disable_unprepare to simplify
code. No functional change.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no meaningful code sharing between the PIO and DMA variants
(just the timeout calculation) so in order to make the code easier to
work with split the two cases.
Looking at the code it is not clear how the PIO version works for large
transmits, greater than FIFO size is only handled for RX.
Signed-off-by: Mark Brown <broonie@linaro.org>
The GPIO enable and disable is done in the core so does not need to be
replicated in the driver, delete the unneeded code. enable_cs() was not
referenced at all.
Signed-off-by: Mark Brown <broonie@linaro.org>
When used via spidev with more than one messages to tranfer via
SPI_IOC_MESSAGE the current implementation would return with
-EINVAL, since bits_per_word and speed_hz are set in all
transfer structs. And in the 2nd loop status will stay at
-EINVAL as its not overwritten again via fsl_spi_setup_transfer().
This patch changes this behavious by first checking if one of
the messages uses different settings. If this is the case
the function will return with -EINVAL. If not, the messages
are transferred correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the pointer-integer size mismatch warning below:
drivers/spi/spi-gpio.c: In function ‘spi_gpio_setup’:
drivers/spi/spi-gpio.c:252:8: warning: cast from pointer to integer of
different size [-Wpointer-to-int-cast]
cs = (unsigned int) spi->controller_data;
^
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
rspi_wait_for_interrupt() unconditionally enables interrupts, even when the
wait condition is already satisfied. This causes a high interrupt load (2
interrupts/byte for full-duplex Single SPI transfers, 1 interrupt/byte for
RSPI with TX Only mode, or QSPI in unidirectional Dual or Quad Transfer
mode).
Change this to return immediately when the wait condition is satisfied.
This dramatically reduces the interrupt load, especially in high-speed
Quad Transfer mode, and increases transfer speed, as no interrupts need to
be handled when there's space available in the output FIFO, or data
available in the input FIFO.
Benchmark results for QSPI on r8a7791 while reading 1 MiB from 30 MHz SPI
FLASH on the Koelsch development board:
Before:
Single SPI Dual SPI Quad SPI
Interrupts: 2096856 1048592 1048594
Mbps: 0.9 1.6 1.6
After:
Single SPI Dual SPI Quad SPI
Interrupts: 1048569 21295 8
Mbps: 0.7 10.8 12.9
I don't know why Single SPI slowed down a bit.
I've also verified functionality for RSPI-RZ on r7s72100, but don't have
benchmark results as there's no SPI FLASH connected to RSPI on the Genmai
development board. Unlike RSPI and QSPI, RSPI-RZ has separate interrupts
for RX and TX, which shows that Single SPI transfers now generate (mostly)
RX interrupts, as expected.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently a divide-by-2^n clock is used, causing a very coarse
clock selection, i.e. a 10MHz device will need to use a 6MHz
clock. The McSPI can also use a divide-by-n clock, this patch
adds support for selecting that when possible.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
spi_transfer->speed_hz and spi_transfer->bits_per_word used to only be set when
not using the default settings but are not set on every transfer, causing
omap2_mcspi_setup_transfer to be called on each transfer. This patch changes
the check to only call omap2_mcspi_setup_transfer if the settings needs to be
changed.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for 1 to 8 BPW to driver and removes
excess BPW validation since this is already checked by SPI core.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fixes an issue that the following build error happens when
the CONFIG_OF is not set:
drivers/spi/spi-rspi.c: In function 'rspi_probe':
drivers/spi/spi-rspi.c:1203:26: error: 'rspi_of_match' undeclared (first use in this function)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The process of DMA mapping buffers for SPI transfers does not vary between
devices so in order to save duplication of code in drivers this can be
factored out into the core, allowing it to be integrated with the work that
is being done on factoring out the common elements from the data path
including more sharing of dmaengine code.
In order to use this masters need to provide a can_dma() operation and while
the hardware is prepared they should ensure that DMA channels are provided
in tx_dma and rx_dma. The core will then ensure that the buffers are mapped
for DMA prior to calling transfer_one_message().
Currently the cleanup on error is not complete, this needs to be improved.
Signed-off-by: Mark Brown <broonie@linaro.org>
Don't wait indefinitely for transfers to complete but time out after 10ms
more than we expect the transfer to take on the wire.
Signed-off-by: Mark Brown <broonie@linaro.org>
For better readability, and then we can remove the comment for last transfer.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Trivial cleanup to avoid duplicate code in various bits_per_word cases.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The checking for spi->mode is done in the implementation of spi_setup().
Calling sc18is602_check_transfer(spi, NULL, 0) is pointless because
the code is equivent to checking if spi->max_speed_hz is 0.
Note, sc18is602_check_transfer actually allows spi->max_speed_hz is 0
if t->speed_hz is set. So return error in sc18is602_setup() when
spi->max_speed_hz is 0 does not make sense.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
When the driver was converted to clk_prepare() the suspend path didn't
have any changes made so the clock remains prepared throughout the runtime
of the driver. Unprepare it when suspended so that any savings that can be
made as a result are made.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since 93abe8e4 (clk: add non CONFIG_HAVE_CLK routines) code using clk.h
like this platform driver needs not depend on HAVE_CLK.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the platform_device id to uniquely identify each SPI master instance.
Cc: Jean-Hugues Deschenes <jean-hugues.deschenes@octasic.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for Quad and Dual SPI Transfers on the Renesas Quad Serial
Peripheral Interface, as found in R-Car Gen2 SoCs like R-Car H2 (r8a7790)
and R-Car M2 (r8a7791):
- Add unidirectional transfer methods for Quad/Dual SPI Transfers.
- Program the sequencer to handle SPI messages with multiple transfer
modes when Quad or Dual transfers are enabled for an SPI slave.
Up to 4 transfer modes per SPI message are supported by the hardware.
- Advertise the availability of Quad and Dual SPI modes on QSPI.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
<<
Switch mpc512x to the common clock framework and adapt mpc512x
drivers to use the new clock driver. Old PPC_CLOCK code is
removed entirely since there are no users any more.
>>
This reverts commit e120cc0dcf.
It causes a NULL pointer dereference with drivers using the generic
spi_transfer_one_message(), which always calls
spi_finalize_current_message(), which zeroes master->cur_msg.
Drivers implementing transfer_one_message() theirselves must always call
spi_finalize_current_message(), even if the transfer failed:
* @transfer_one_message: the subsystem calls the driver to transfer a single
* message while queuing transfers that arrive in the meantime. When the
* driver is finished with this message, it must call
* spi_finalize_current_message() so the subsystem can issue the next
* transfer
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
There's only one RSPI/QSPI clock, so we can use NULL as the clock ID
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Get the driver ready for the migration to the common clock framework by
calling clk_prepare_enable() and clk_disable_unprepare().
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for specifying loopback mode.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for the RSPI variant in the RZ/A1H (r7s72100) SoC.
Main differences with RSPI on SH are:
- Lack of TX only mode, hence we always have to use full duplex
transfers,
- The Data Register must be accessed used 8-bit operations.
RSPI on RZ is matched using the new "rspi-rz" platform device name.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for multiple interrupts, based on the SDK reference code.
This is needed for RZ/A1H, which supports 3 interrupts.
When using multiple interrupts, they must be called "rx" (SPRI) and "tx"
(SPTI). The error interrupt (SPEI) is not used, as it matters for slave
mode only.
When using a single interrupt, it may be called "mux". If it cannot be
found, the first interrupt in the device's resources will be used.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
qspi_send_pio() and qspi_receive_pio() are very similar: they both send
and receive full duplex data to/from the hardware, but ignore the data
stream in the unused direction.
Merge them into qspi_transfer_out_in(), now supporting real full duplex.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
rspi_send_pio() and rspi_receive_pio() are very similar:
- the former only sends data, using TX Only Mode,
- the latter sends and receives full duplex data to/from the hardware,
but uses dummy transmit data.
Merge them into rspi_transfer_out_in(), now supporting full duplex if
needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Split off qspi_transfer_one() (which doesn't support DMA yet) from
rspi_transfer_one().
Replace the abstraction of send_pio()/receive_pio() by the abstracrion of
transfer_one().
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add helpers rspi_data_{out,in,out_in}() to write, read, or write and
read data to/from the Data Register, taking care of waiting until data
or space is available in the buffers.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add rspi_{write,read}_data(), to abstract 8-bit (QSPI, and RSPI on RZ/A1H)
versus 16-bit (RSPI) Data Register access.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Let the generic SPI core handle SPI messages, calling into our
rspi_transfer_one() method.
rspi_assert_ssl() and rspi_negate_ssl() are absorbed into
rspi_prepare_message() and rspi_unprepare_message(), as they actually
enable/disable the whole SPI function, instead of just (de)asserting the
chip select line.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
A respun version of the merges for the pull request previously sent with
a few additional fixes. The last two merges were fixed up by hand since
the branches have moved on and currently have the prior merge in them.
Quite a busy release for the SPI subsystem, mostly in cleanups big and
small scattered through the stack rather than anything else:
- New driver for the Broadcom BC63xx HSSPI controller.
- Fix duplicate device registration for ACPI.
- Conversion of s3c64xx to DMAEngine (this pulls in platform and DMA
changes upon which the transiton depends).
- Some small optimisations to reduce the amount of time we hold locks
in the datapath, eliminate some redundant checks and the size of a
spi_transfer.
- Lots of fixes, cleanups and general enhancements to drivers,
especially the rspi and Atmel drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=CbUw
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A respun version of the merges for the pull request previously sent
with a few additional fixes. The last two merges were fixed up by
hand since the branches have moved on and currently have the prior
merge in them.
Quite a busy release for the SPI subsystem, mostly in cleanups big and
small scattered through the stack rather than anything else:
- New driver for the Broadcom BC63xx HSSPI controller
- Fix duplicate device registration for ACPI
- Conversion of s3c64xx to DMAEngine (this pulls in platform and DMA
changes upon which the transiton depends)
- Some small optimisations to reduce the amount of time we hold locks
in the datapath, eliminate some redundant checks and the size of a
spi_transfer
- Lots of fixes, cleanups and general enhancements to drivers,
especially the rspi and Atmel drivers"
* tag 'spi-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (112 commits)
spi: core: Fix transfer failure when master->transfer_one returns positive value
spi: Correct set_cs() documentation
spi: Clarify transfer_one() w.r.t. spi_finalize_current_transfer()
spi: Spelling s/finised/finished/
spi: sc18is602: Convert to use bits_per_word_mask
spi: Remove duplicate code to set default bits_per_word setting
spi/pxa2xx: fix compilation warning when !CONFIG_PM_SLEEP
spi: clps711x: Add MODULE_ALIAS to support module auto-loading
spi: rspi: Add missing clk_disable() calls in error and cleanup paths
spi: rspi: Spelling s/transmition/transmission/
spi: rspi: Add support for specifying CPHA/CPOL
spi/pxa2xx: initialize DMA channels to -1 to prevent inadvertent match
spi: rspi: Add more QSPI register documentation
spi: rspi: Add more RSPI register documentation
spi: rspi: Remove dependency on DMAE for SHMOBILE
spi/s3c64xx: Correct indentation
spi: sh: Use spi_sh_clear_bit() instead of open-coded
spi: bitbang: Grammar s/make to make/to make/
spi: sh-hspi: Spelling s/recive/receive/
spi: core: Improve tx/rx_nbits check comments
...
- ACPI core changes to make it create a struct acpi_device object for every
device represented in the ACPI tables during all namespace scans regardless
of the current status of that device. In accordance with this, ACPI hotplug
operations will not delete those objects, unless the underlying ACPI tables
go away.
- On top of the above, new sysfs attribute for ACPI device objects allowing
user space to check device status by triggering the execution of _STA for
its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating the
PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the code
"glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for the
DBG2 and PCCT tables to ACPICA, fixes some bugs and improves debug
facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization earlier.
That should allow us to use ACPI during the timekeeping initialization
and possibly to simplify the EFI initialization too. From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over from
Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in drivers
that uses _DSM to execute it via the new helper. From Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun Guo,
Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava, Rashika Kheria,
Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support, from
Dirk Brandewie and intel_pstate documentation from Ramkumar Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John Tobias,
Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC disabled
during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente Kurusa,
Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a cpupower
tool cleanup from One Thousand Gnomes.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=dRf6
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"As far as the number of commits goes, the top spot belongs to ACPI
this time with cpufreq in the second position and a handful of PM
core, PNP and cpuidle updates. They are fixes and cleanups mostly, as
usual, with a couple of new features in the mix.
The most visible change is probably that we will create struct
acpi_device objects (visible in sysfs) for all devices represented in
the ACPI tables regardless of their status and there will be a new
sysfs attribute under those objects allowing user space to check that
status via _STA.
Consequently, ACPI device eject or generally hot-removal will not
delete those objects, unless the table containing the corresponding
namespace nodes is unloaded, which is extremely rare. Also ACPI
container hotplug will be handled quite a bit differently and cpufreq
will support CPU boost ("turbo") generically and not only in the
acpi-cpufreq driver.
Specifics:
- ACPI core changes to make it create a struct acpi_device object for
every device represented in the ACPI tables during all namespace
scans regardless of the current status of that device. In
accordance with this, ACPI hotplug operations will not delete those
objects, unless the underlying ACPI tables go away.
- On top of the above, new sysfs attribute for ACPI device objects
allowing user space to check device status by triggering the
execution of _STA for its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating
the PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the
code "glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for
the DBG2 and PCCT tables to ACPICA, fixes some bugs and improves
debug facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization
earlier. That should allow us to use ACPI during the timekeeping
initialization and possibly to simplify the EFI initialization too.
From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over
from Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in
drivers that uses _DSM to execute it via the new helper. From
Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun
Guo, Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava,
Rashika Kheria, Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support,
from Dirk Brandewie and intel_pstate documentation from Ramkumar
Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz
Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark
Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John
Tobias, Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh
Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC
disabled during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf
Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente
Kurusa, Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a
cpupower tool cleanup from One Thousand Gnomes"
* tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (153 commits)
thermal: exynos: boost: Automatic enable/disable of BOOST feature (at Exynos4412)
cpufreq: exynos4x12: Change L0 driver data to CPUFREQ_BOOST_FREQ
Documentation: cpufreq / boost: Update BOOST documentation
cpufreq: exynos: Extend Exynos cpufreq driver to support boost
cpufreq / boost: Kconfig: Support for software-managed BOOST
acpi-cpufreq: Adjust the code to use the common boost attribute
cpufreq: Add boost frequency support in core
intel_pstate: Add trace point to report internal state.
cpufreq: introduce cpufreq_generic_get() routine
ARM: SA1100: Create dummy clk_get_rate() to avoid build failures
cpufreq: stats: create sysfs entries when cpufreq_stats is a module
cpufreq: stats: free table and remove sysfs entry in a single routine
cpufreq: stats: remove hotplug notifiers
cpufreq: stats: handle cpufreq_unregister_driver() and suspend/resume properly
cpufreq: speedstep: remove unused speedstep_get_state
platform: introduce OF style 'modalias' support for platform bus
PM / tools: new tool for suspend/resume performance optimization
ACPI: fix module autoloading for ACPI enumerated devices
ACPI: add module autoloading support for ACPI enumerated devices
ACPI: fix create_modalias() return value handling
...
This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep it
strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared with Mike
Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for multiplatform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3CcT
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep
it strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared
with Mike Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for
multiplatform"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h
ARM: mvebu: remove prototypes of non-existing functions from common.h
ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h
serial: sh-sci: Rework baud rate calculation
serial: sh-sci: Compute overrun_bit without using baud rate algo
serial: sh-sci: Remove unused GPIO request code
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
serial: sh-sci: Support resources passed through platform resources
serial: sh-sci: Don't check IRQ in verify port operation
serial: sh-sci: Set the UPF_FIXED_PORT flag
serial: sh-sci: Remove duplicate interrupt check in verify port op
serial: sh-sci: Simplify baud rate calculation algorithms
serial: sh-sci: Remove baud rate calculation algorithm 5
serial: sh-sci: Sort headers alphabetically
ARM: EXYNOS: Kill exynos_pm_late_initcall()
ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
ARM: at91: switch Calao QIL-A9260 board to DT
clk: at91: fix pmc_clk_ids data type attriubte
PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
...
master->transfer_one returns positive value is not a error.
So set ret to 0 when master->transfer_one returns positive value.
Otherwise, I hit "spi_master spi0: failed to transfer one message from queue"
error when my transfer_one callback returns 1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 543bb25 "spi: add ability to validate xfer->bits_per_word in SPI
core", the driver can set bits_per_word_mask for the master then the SPI core
will reject transfers that attempt to use an unsupported bits_per_word value.
So we can remove the bits_per_word checking in sc18is602_check_transfer() and
let SPI core handle the checking.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
The implementation in spi_setup() already set spi->bits_per_word = 8 when
spi->bits_per_word is 0 before calling spi->master->setup.
So we don't need to do it again in setup() callback.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
ACPI enumerated devices has ACPI style _HID and _CID strings,
all of these strings can be used for both driver loading and matching.
Currently, in Platform, I2C and SPI bus, the ACPI style driver matching
is supported by invoking acpi_driver_match_device() in bus .match() callback.
But, the module autoloading is still broken.
For example, there is any ACPI device with _HID "INTABCD" that is
enumerated to platform bus, and we have a driver that can probe it.
The driver exports its module_alias as "acpi:INTABCD" use the following code
static const struct acpi_device_id xxx_acpi_match[] = {
{ "INTABCD", 0 },
{ }
};
MODULE_DEVICE_TABLE(acpi, xxx_acpi_match);
But, unfortunately, the device' modalias is shown as "platform:INTABCD:00",
please refer to modalias_show() and platform_uevent() in
drivers/base/platform.c.
This results in that the driver will not be loaded automatically when the
device node is created, because their modalias do not match.
This also applies to I2C and SPI bus.
With this patch, the device' modalias will be shown as "acpi:INTABCD" as well.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CONFIG_PM will be set if either or both CONFIG_PM_SLEEP and
CONFIG_PM_RUNTIME is set. Compiling the driver with !CONFIG_PM_SLEEP causes
following compilation warning:
drivers/spi/spi-pxa2xx.c:1270:12: warning: ‘pxa2xx_spi_suspend’ defined but not used [-Wunused-function]
Fix this by using CONFIG_PM_SLEEP instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for specifying the SPI clock phase and polarity, based on the
SDK reference code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit cddb339bad (spi/pxa2xx: convert to dma_request_slave_channel_compat())
converted the driver to use ACPI provided DMA helpers but it forgot to
initialize the platform data for the channels to -1. Failing to do so will
result inadvertent match in the filter function because 0 is a valid
channel number.
Prevent this from happening by initializing both platform data channels
correctly to -1.
Fixes: cddb339bad (spi/pxa2xx: convert to dma_request_slave_channel_compat())
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
On ARM-based SHMOBILE, the rspi driver builds and works fine without the
DMA controller driver, hence relax the dependencies.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
We have a spi_sh_clear_bit() function, there's no reason not to use it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
- Rephrase the comments about tx/rx_nbits validity checks,
- Remove the stale comment about SPI_3WIRE (the code it refers to was
removed in commit 368ca4e0c7 ("spi:
Eliminate 3WIRE spi_transfer check")).
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver name in current code looks like a compatible string which is not
the naming convention for platform drivers.
Fix it and also add modalias since this driver can be built as a module.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make the unit of wlen to be byte, and simplify the code to avoid duplicate
code for different wlen cases.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We already has NULL test for master after calling spi_alloc_master().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
after device tree based clock lookup became available, the peripheral
driver need no longer construct clock names which include the PSC index,
remove the "psc%d_mclk" template and unconditionally use 'mclk'
acquire and release the 'ipg' clock item for register access as well
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-spi@vger.kernel.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch replaces gpio_request() with devm_ API.
As a result this simplifies error path and eliminates "remove"
function.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently we have similar code for (txp && rxp), (txp && !rxp), (!rxp & txp),
and (!txp && !rxp) cases. This patch refactors the code a bit to avoid
duplicate similar code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Replace the deprecated master->transfer with transfer_one_message()
and allow the SPI subsystem handle all the queuing of messages.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no need to force selection of TI EDMA DMA engine
driver when DaVinci SPI driver is selected. The driver
builds just fine even with CONFIG_TI_EDMA disabled.
Forcing this selection causes warnings of the sort:
warning: (ARCH_KEYSTONE && SPI_DAVINCI) selects TI_EDMA which has unmet direct dependencies (DMADEVICES && (ARCH_DAVINCI || ARCH_OMAP || ARCH_KEYSTONE))
This reverts commit b5f1433059.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit e13ac47bec (spi: Use stable dev_name for ACPI enumerated SPI
slaves) changed the SPI device naming to be based on ACPI device name
instead of carrying bus number and chip select for devices enumerated
from ACPI namespace.
In case of a buggy BIOS that lists multiple SPI devices sharing the same
chip select (even though they should use different) the current code fails
to detect that and allows the devices to be added to the bus.
Fix this by walking through the bus and comparing spi->chip_select instead
of device name. This should work regardless what the device name will be in
future.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
fiq.h contains only a function declaration and is not used by anyone
else. Move the declaration to the driver header file and remove the
unnecessary platform dependency from the driver.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The only speed available was max_speed (the maximum speed declared for a
device).
This patch adds the support for spi_tranfer->speed_hz parameter.
We can now set a different speed for each spi message.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make the modalias matches the driver name.
Seems the MODULE_ALIAS is copied from drivers/spi/spi-sh-spi.c.
So both spi-sh.ko and spi-sh-hspi.ko have the same alias. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
It's not necessary to free resources allocated with devm_*
and free them may lead to double free.
Fixes: 04f421e7b0 ('spi: dw: use managed resources')
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now platform_get_drvdata() returns the address of qspi rather than master.
Also drop unneeded spi_unregister_master() call in ti_qspi_remove() because
we use devm_spi_register_master() in probe.
commit cbcabb7a30 "spi/qspi: Fix qspi remove path" assumes
platform_get_drvdata() returns address of master. However,
commit 160a061301 "spi/qspi: set correct platform drvdata in ti_qspi_probe()"
pass qspi to platform_set_drvdata().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This corrects a problem in spi_pump_messages() that leads to an spi
message hanging forever when a call to transfer_one_message() fails.
This failure occurs in my MCP2210 driver when the cs_change bit is set
on the last transfer in a message, an operation which the hardware does
not support.
Rationale
Since the transfer_one_message() returns an int, we must presume that it
may fail. If transfer_one_message() should never fail, it should return
void. Thus, calls to transfer_one_message() should properly manage a
failure.
Fixes: ffbbdd2132 (spi: create a message queueing infrastructure)
Signed-off-by: Daniel Santos <daniel.santos@pobox.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Axel Lin