The code currently uses variables to store and never modify the bit masks
of interrupts. This is legacy code from an early version of the driver
that supported MIPS based SoCs where the IRQ bits depended on the actual
SoC. As the bits are the same for all ARM based SoCs using this driver we
can remove the intermediate variables.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was originally written for MIPS based SoC. These required the
IRQ mask register to be read after writing it to ensure that the content
was actually applied. As this version only works on ARM based SoCs, we can
safely remove the 2 reads as they are no longer required.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms, syncing a buffer for DMA is expensive. Rather than
sync the whole 2K receive buffer, only synchronise the length of the
frame, which will typically be the MTU, or a much smaller TCP ACK.
For an IMX6Q, this gives around 6% increased TCP receive performance,
which is cache operations bound and reduces CPU load for TCP transmit.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When setting spoofing, both VLAN and MAC need to be set together.
This change resolves an issue where MAC-VLANs on the VF fail to pass
traffic due to spoofed packets.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update ixgbe_ethtool_get_ts_info() to show that x550 supports hardware
timestamping of all packets.
Reported-by: Guy Harris <guy@alum.mit.edu>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
alloc_workqueue replaces deprecated create_workqueue().
A dedicated workqueue has been used since the workitem (viz
fm10k_service_task, which manages and runs other subtasks) is involved in
normal device operation and requires forward progress under memory
pressure.
create_workqueue has been replaced with alloc_workqueue with max_active
as 0 since there is no need for throttling the number of active work
items.
Since network devices may be used in memory reclaim path,
WQ_MEM_RECLAIM has been set to guarantee forward progress.
flush_workqueue is unnecessary since destroy_workqueue() itself calls
drain_workqueue() which flushes repeatedly till the workqueue
becomes empty. Hence the call to flush_workqueue() has been dropped.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Properly stop the extra workqueue items and ensure that we resume
cleanly. This is better than using igb_ptp_init and igb_ptp_stop since
these functions destroy the PHC device, which will cause other problems
if we do so. Since igb_ptp_reset now re-schedules the work-queue item we
don't need an equivalent igb_ptp_resume in the resume workflow.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make igb_ptp_stop take advantage of this new function to reduce code
duplication.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Modify igb_ptp_init to take advantage of igb_ptp_reset, and remove
duplicated work that was occurring in both igb_ptp_reset and
igb_ptp_init.
In total, resetting the TSAUXC register, and resetting the system time
both happen in igb_ptp_reset already. igb_ptp_reset now also takes care
of starting the delayed work item for overflow checks, as well.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't continue to use complex MAC type checks for handling various cases
where we have overflow check code. Make this code more obvious by
introducing a flag which is enabled for hardware that needs these
checks.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Upcoming patches will introduce new PTP specific flags. To avoid
cluttering the normal flags variable, introduce PTP specific "ptp_flags"
variable for this purpose, and move IGB_FLAG_PTP to become
IGB_PTP_ENABLED.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For u32 classifier filters, avoid overwriting existing filter
in a hardware location without removing it first, to clean up
inconsistencies due to duplicate values for filter location.
Verified with the following filters:
Create child hash tables:
handle 1: u32 divisor 1
handle 2: u32 divisor 1
Link to the child hash table from parent hash table:
handle 800:0:11 u32 ht 800: link 1: \
offset at 0 mask 0f00 shift 6 plus 0 eat \
match ip protocol 6 ff match ip dst 15.0.0.1/32
handle 800:0:12 u32 ht 800: link 2: \
offset at 0 mask 0f00 shift 6 plus 0 eat \
match ip protocol 17 ff match ip dst 16.0.0.1/32
Add filter into child hash table:
handle 1:0:3 u32 ht 1: \
match tcp src 22 ffff action drop
Add another filter to the same location:
handle 2:0:3 u32 ht 2: \
match tcp src 33 ffff action drop
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On deleting filters which are links to a child hash table, the filters
in the child hash table must be cleared from the hardware if there
is no link between the parent and child hash table.
Verified with the following filters:
Create a child hash table:
handle 1: u32 divisor 1
Link to the child hash table from parent hash table:
handle 800:0:10 u32 ht 800: link 1: \
offset at 0 mask 0f00 shift 6 plus 0 eat \
match ip protocol 6 ff match ip dst 15.0.0.1/32
Add filters into child hash table:
handle 1:0:2 u32 ht 1: \
match tcp src 22 ffff action drop
handle 1:0:3 u32 ht 1: \
match tcp src 33 ffff action drop
Delete link filter from parent hash table:
handle 800:0:10 u32
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Users report that under VMWare, er32(TIMINCA) returns zero.
This causes division by zero at init time as follows:
==> incvalue = er32(TIMINCA) & E1000_TIMINCA_INCVALUE_MASK;
for (i = 0; i < E1000_MAX_82574_SYSTIM_REREADS; i++) {
/* latch SYSTIMH on read of SYSTIML */
systim_next = (cycle_t)er32(SYSTIML);
systim_next |= (cycle_t)er32(SYSTIMH) << 32;
time_delta = systim_next - systim;
temp = time_delta;
====> rem = do_div(temp, incvalue);
This change makes kernel survive this, and users report that
NIC does work after this change.
Since on real hardware incvalue is never zero, this should not affect
real hardware use case.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The index calculated when looping through the indir array passed to
fm10k_write_reta was incorrectly calculated as the first part i needs to
be multiplied by 4.
Fixes: 0cfea7a65738 ("fm10k: fix possible null pointer deref after kcalloc", 2016-04-13)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While reviewing the i40e driver changes to support page based receive I
realized that I had overlooked the fact that the fm10k hardware required a
512 byte alignment for Rx buffers. This patch is meant to address that by
changing the alignment for Rx buffers to 512 bytes instead of allowing it
to be L1 cache aligned.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The FM10K_MAX_DATA_PER_TXD is really just using a bitshift as a power of
2 operation in an efficient manner. We shouldn't represent this as a BIT()
because that obscures the intention of the operation.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now ixgbevf_write/read_posted_mbx use -IXGBE_ERR_MBX as the initiative
return value, but it's incorrect, cause in ixgbevf_vlan_rx_add_vid(),
it use err == IXGBE_ERR_MBX, the err returned from mac.ops.set_vfta,
and in ixgbevf_set_vfta_vf, it return from write/read_posted. so we
should initialize err with IXGBE_ERR_MBX, instead of -IXGBE_ERR_MBX.
With this fix, the other functions that called it also can work well,
cause they only care about if err is 0 or not.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The bit in the e1000 driver that mentions explicitly that the hardware
has no support for separate RX/TX VLAN accel toggling rings true for
e1000e as well, and thus both NETIF_F_HW_VLAN_CTAG_RX and
NETIF_F_HW_VLAN_CTAG_TX need to be kept in sync.
Revert a portion of commit 889ad45666 ("e1000e: keep VLAN interfaces
functional after rxvlan off") since keeping the bits in sync resolves
the original issue.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-06-27
This series contains updates to i40e and i40evf only.
Mitch provides several changes, first adds functions to enable and disable
VSI on a VEB, which allows for configuration of limited promiscuous mode
specifically for bridging purposes. Sets the RSS Hash Enable registers by
default now that VF RSS is configured by the PF driver. Fixed a issue
where we could overflow the buffer, by checking the address count and bail
out of the loop at the appropriate time. Removed the need for a reset
when the device enters limited promiscuous mode, since this was causing
heartburn for people who were using VFs and bridging.
Catherine adds a call to set the client interface down when we put the VSI
down. Fixed an issue where RSS queues was being limited to the number
of CPUs, so if a user wants to use more queues than CPUs, we want to
trust they know what they are doing and let them.
Greg cleans up the driver suspend routine to ensure we are calling
synchronize_irq() before freeing IRQ vectors and explicitly free the other
causes interrupt resources and shut down the MSIX interrupt.
Serey fixes i40e_set_settings() to not fail when a Direct Attach (DA)
cable is used.
Avinash fixes a supported link bug by removing code which was not allowing
100BaseT to show up in the supported link modes for 10GBaseT PHYs.
Shannon adds a bit of information to the error messages to help determine
the source of error by adding VSI info to macaddr messages.
Tushar Dave fixes error received when turning off TSO on some systems,
which was caused by enabling FD_SB without checking availability of
MSIx vectors, so add the check.
Neerav fixes a possible panic when LLDP/DCBX change happens and the
driver tried to notify the client(s) for each of the PF VSIs, which would
panic when it reached a VSI that did not have any netdev associated with
it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SPQ doorbell is currently protected with the compilation barrier. Under the
stress scenarios, we may get into a state where (due to the weak ordering)
several ramrod doorbells were written to the BAR with an out-of-order
producer values. Need to change the barrier type to a write barrier to make
sure that the write buffer is flushed after each doorbell.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Static checker warnings:
drivers/net/ethernet/qlogic/qede/qede_ethtool.c:435 qede_get_coalesce()
warn: passing casted pointer '&coal->rx_coalesce_usecs' to
'edev->ops->common->get_coalesce()' 32 vs 16.
The u32 pointer is being typecasted to u16 which may fail for big-endian
platforms.
Fixes: d552fa84cb ("qede: Add support for coalescing config read/update.")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've got a bug report about an e1000e interface, where a VLAN interface is
set up on top of it:
$ ip link add link ens1f0 name ens1f0.99 type vlan id 99
$ ip link set ens1f0 up
$ ip link set ens1f0.99 up
$ ip addr add 192.168.99.92 dev ens1f0.99
At this point, I can ping another host on vlan 99, ip 192.168.99.91.
However, if I do the following:
$ ethtool -K ens1f0 rxvlan off
Then no traffic passes on ens1f0.99. It comes back if I toggle rxvlan on
again. I'm not sure if this is actually intended behavior, or if there's a
lack of software VLAN stripping fallback, or what, but things continue to
work if I simply don't call e1000e_vlan_strip_disable() if there are
active VLANs (plagiarizing a function from the e1000 driver here) on the
interface.
Also slipped a related-ish fix to the kerneldoc text for
e1000e_vlan_strip_disable here...
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a static checker warning here "warn: mask and shift to zero"
and the code sets "ring" to zero every time. From looking at how
QLCNIC_FETCH_RING_ID() is used in qlcnic_83xx_process_rcv_ring() the
qlcnic_83xx_hndl() should be removed.
Fixes: 4be41e92f7 ('qlcnic: 83xx data path routines')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we will remove items off the list using list_del() we need
to use a safe version of the list_for_each() macro aptly named
list_for_each_safe().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
TL4 calculation for a given SQ of secondary Qsets is incorrect
and goes out of bounds and also for some SQ's TL4 chosen will
transmit data via a different BGX interface and not same as
primary Qset's interface.
This patch fixes this issue.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for SMU RX local/remote faults along with SPU LINK
status. Otherwise at times link is UP at our end but DOWN
at link partner's side. Also due to an issue in BGX it's
rarely seen that initialization doesn't happen properly
and SMU RX reports faults with everything fine at SPU.
This patch tries to reinitialize LMAC to fix it.
Also fixed LMAC disable sequence to properly bring down link.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Tao Wang <tao.wang@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Categorize and reorganize ethtool statistics counters by renaming to
"rx_*" and "tx_*" and removing redundant and duplicated counters, this
way they are easier to grasp and more user friendly.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Number of PFC counters used to count only number of priorities with PFC
enabled, but each priority has more than one counter, hence the need to
multiply it by the number of PFC counters per priority.
Fixes: cf678570d5 ('net/mlx5e: Add per priority group to PPort counters')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not allow the same vxlan udp port to be added to the device more than
once.
Fixes: b3f63c3d5e ("net/mlx5e: Add netdev support for VXLAN tunneling")
Signed-off-by: Matthew Finlay <matt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous to this patch mapping was always set to write combining without
checking whether BlueFlame is supported in the device.
Fixes: 0ba422410b ('net/mlx5: Fix global UAR mapping')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change MLX5E_STATE_ASYNC_EVENTS_ENABLE to
MLX5E_STATE_ASYNC_EVENTS_ENABLED since it represent a state and not an
operation.
Fixes: acff797cd1 ('net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the upcoming ConnectX-5 PCIe 4.0 device to the list of
supported devices by the mlx5 driver.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add command string for MODIFY_FLOW_TABLE which is used by the driver.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TI CPDMA currently uses a bitmap for tracking descriptors alloactions
allocations, but The genalloc already handles the same and can be used
as with special memory (SRAM) as with DMA cherent memory chank
(dma_alloc_coherent()). Hence, switch to using genalloc and add
desc_num property for each channel for limitation of max number of
allowed descriptors for each CPDMA channel. This patch do not affect
on net throuput.
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use "ti,cpsw-mdio" to enable PM runtime auto-suspend on supported
platforms, where MDIO is implemented as part of TI CPSW.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davinci MDIO is always used as slave device which services
read/write requests from MDIO/PHY core. It doesn't use IRQ also.
As result, It's possible to relax PM runtime constraints for Davinci
MDIO and enable it on demand, instead of powering it during probe
and powering off during removal.
Hence, implement PM runtime autosuspend for Davinci MDIO, but keep it
disabled by default, because Davinci MDIO is integrated in big set of
TI devices and not all of them expected to work corectly with RPM
autosuspend enabled:
- expected to work on SoCs where MDIO is part of TI CPSW
(cpsw.c DRA7/am57x, am437x, am335x, dm814x)
- not verified on Keystone 2 and other SoCs where MDIO is used with TI EMAC IP
(davinci_emac.c: dm6467-emac, am3517-emac, dm816-emac).
Davinci MDIO RPM autosuspend can be enabled through sysfs:
echo 100 > /sys/devices/../48484000.ethernet/48485000.mdio/power/autosuspend_delay_ms
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PM runtime .runtime_suspend()/.runtime_resume() callbacks and
perform Davinci MDIO enabling/disabling from these callbacks. This
allows to reuse pm_runtime_force_suspend/resume() APIs during System
suspend and required for further implementation of PM runtime
autosuspend.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Davinci MDIO MDIO_CONTROL.CLKDIV can be calculated only once
during probe, hence split __davinci_mdio_reset() on
davinci_mdio_init_clk() and davinci_mdio_enable(). Initialize and
save CLKDIV in .probe(). Then just use saved value.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not expected Davinci MDIO to be accessible after its suspend
callbacks have been called:
- all consumers of Davinci MDIO will stop/disconnect phys at Device
suspend stage;
- all phys are expected to be suspned already by PHY/MDIO core;
- MDIO locking is done by MDIO Bus code.
Hence, it's safe to drop "suspended" and "lock" fields from mdio_data.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PM runtime is disabled when Davinci MDIO .suspend_late() and
.resume_early() callbacks are called. As result, any PM runtime calls here will
be just a nop and can be removed.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do PM runtime initialization later in probe - this allows to simplify
error handling a bit.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPSW might be suspended by RPM if all ethX interfaces are down,
but it still could be accesible through net_device_ops interfce. In
this case net_device_ops operations requiring registers access will
cause L3 errors and CPSW crash.
Hence, fix it by adding RPM get/put calls in net_device_ops callbacks
which need to access CPSW registers: .ndo_set_mac_address(),
.ndo_vlan_rx_add_vid(), .ndo_vlan_rx_kill_vid().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPSW might be suspended by RPM if all ethX interfaces are down,
but it still could be accesible through ethtool interfce. In this case
ethtool operations, requiring registers access, will cause L3 errors and
CPSW crash.
ethtool callbcaks which need to access CPSW registers now:
.set_coalesce(), .get_ethtool_stats(), .set_pauseparam(), .get_regs()
Hence, fix it by adding .begin()/.complete() ethtool callbacks, which
will be called before/after each ethtool operation runs, and do CPSW
RPM handling in these callbacks. That way CPSW will be active while
handling ethtool requests.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PM runtime is properly handled in cpsw_ndo_open/stop(), as result it
isn't required to duplicate these calls in .suspend()/.resume()
callbacks. Moreover, it might cause unnecessary RPM resume of CPSW
during System suspend in the case it's already suspended because
all ethX interfaces are down already, before System suspend started.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missed check of return code from PM runtime get() calls.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw_suspend() could trigger L3 error and CPSW will stop
functioning if System enters suspend when all ethX net-devices are
down - in this case CPSW could be already suspended by PM runtime, but
cpsw_suspend() will try to call soft_reset_slave() unconditionally
and access CPSW registers.
Hence, fix it by moving soft_reset_slave() from cpsw_suspend() to
cpsw_slave_stop(). This way slave ports will be reset when CPSW is
active and will be in proper state during Suspend.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of SGMII more, for example when a MAC2MAC connection
is needed, the port selection bits (inside the MAC configuration
registers) have to be programmed according to the link selected.
So the patch adds a new DT parameter to pass the port selection
and to programmed related PCS and CORE to use it.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, all gmac cores disable the PCS block and always
enable the PMT.
Note that this is done in a different way by 3.x and 4.x cores.
With this rework, PCS and PMT interrupt masks can be driven by
parameters now moved inside the mac_device_info structure
and the settings follow what the HW capability register reports.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 3.xx and 4.xx synopsys gmacs have a very similar
PCS embedded module and they share almost the same registers:
for example:
AN_Control, AN_Status, AN_Advertisement, AN_Link_Partner_Ability,
AN_Expansion, TBI_Extended_Status.
Just the RGMII/SMII Control/Status register differs.
So This patch aims to reorganize and enhance the PCS support.
It removes the existent support from the dwmac1000/dwmac4_core.c
moving basic PCS functions inside a new file called: stmmac_pcs.h.
The patch also reviews the available APIs to be better shared among
different hardware and easily enhanced to support new features.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 311c7c71c9 ("net/mlx5e: Allocate DMA coherent memory on
reader NUMA node") introduced mlx5_*_alloc_node() but missed changing
some calling and warn messages. This patch introduces 2 changes:
* Use mlx5_buf_alloc_node() instead of mlx5_buf_alloc() in
mlx5_wq_ll_create()
* Update the failure warn messages with _node postfix for
mlx5_*_alloc function names
Fixes: 311c7c71c9 ("net/mlx5e: Allocate DMA coherent memory on reader NUMA node")
Signed-off-by: Wang Sheng-Hui <shhuiw@foxmail.com>
Acked-By: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bgmac_open() calls phy_start() to initialize the PHY state machine,
which will set the interface's carrier state accordingly, no need to
force that as this could be conflicting with the PHY state determined by
PHYLIB.
Fixes: dd4544f054 ("bgmac: driver for GBit MAC core on BCMA bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver does not start the transmit queue in bgmac_open(). If the
queue was stopped prior to closing then re-opening the interface, we
would never be able to wake-up again.
Fixes: dd4544f054 ("bgmac: driver for GBit MAC core on BCMA bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are checking for the Start of Frame bit in the ctl1 word, while this
bit is set in the ctl0 word instead. Read the ctl0 word and update the
check to verify that.
Fixes: 9cde94506e ("bgmac: implement scatter/gather support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When LLDP/DCBX change happens the i40e driver code flow tried to
notify the client(s) for each of the PF VSIs. This resulted into
kernel panic on the first VSI that didn't have any netdev
associated to it.
The DCB change notification to the client(s) should be done only
once for the PF/LAN VSI where the client(s) instances have been
added to. Also, move the notification call after the PF driver has
made changes related to the updated DCB configuration.
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Tested-by: Ronald J Bynoe <ronald.j.bynoe@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On systems with 128 CPUs, turning off TSO results in errors,
i40e 0000:03:00.0: failed to get tracking for 1 vectors for VSI 400, err=-12
i40e 0000:03:00.0: Couldn't create FDir VSI
i40e 0000:03:00.0: i40e_ptp_init: PTP not supported on eth0
i40e 0000:03:00.0: couldn't add VEB, err I40E_ERR_ADMIN_QUEUE_ERROR aq_err I40E_AQ_RC_ENOENT
i40e 0000:03:00.0: rebuild of switch failed: -1, will try to set up simple PF connection
i40e 0000:03:00.0 eth0: adding 00:10:e0:8a:24:b6 vid=0
Enabling FD_SB without checking availability of MSI-X vector is the
root cause. This change adds necessary check.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the macaddr add and delete happens asynchronously, error
messages don't easily get associated to the actual request. Here
we add a bit of information to the error messages to help
determine the source of the error.
Change-ID: Id2d6df5287141c3579677d72d8bd21122823d79f
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the need for a reset when the device enters limited promiscuous
mode. This was causing heartburn for people who were using VFs and
bridging, since this would require all of the VFs to undergo a reset
each time the PF changed its promiscuity.
Change-ID: I0a83495c5e4d68112bbc7a7a076d20fa8dd3b61c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Always add MAC address at the tail of the MAC filter list. Since the
device's "real" MAC address is added first, it will always be at the
beginning of the list. This prevents an issue where the "real" MAC
filter might not get added if too many other filters are added before
bringing the interface up.
Change-ID: I34a8aeebeb0cb87a44b24118adc4176c7b943c1c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Limiting qcount to pf->num_lan_msix, effectively limits the RSS queues
to only use the number of CPUs, and ignore all other queues. We don't
want to do this. If the user has changed the RSS settings to use more
queues then CPUS, we want to trust they know what they are doing and
let them. More importantly, if we tell them that is what we did, we want
to actually do it and allow traffic into all of the queues we have
allocated. This does not change the default setting to initially
allocate only the number of CPUS of queue pairs.
Change-ID: Ie941a96e806e4bcd016addb4e17affb46770ada5
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Removing this code which wasn't allowing 100BaseT to show up in the supported
link modes for 10GBaseT PHYs.
Change-ID: Iada2eafa7ef6b4bac9a2a1380ff533ae5de51e1d
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a Direct Attach (DA) cable is used, if the i40e_set_settings
function is called it would return an error. Add the DA type so
the function won't fail.
Change-ID: I2b802f27a5d91cfefa72fd1f852acb4d74647a8e
Signed-off-by: Serey Kong <serey.kong@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_suspend() function was failing to save PCI state
and this would result in a kernel stack trace from a WARN_ONCE in the
pci_legacy_suspend() function.
Add a call to pci_save_state() to fix that problem.
Change-ID: I4736e62bb660966bd208cc8af617a14cb07fc4bd
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_suspend() function calls another function that preps the device
for the power save and resume by freeing all the Tx/Rx resources and
interrupts but that function does not free the "other" causes interrupt
vector and IRQ. It also fails to call synchronize_irq() before freeing
the IRQ vectors. This sometimes may result in some AER errors on those
systems with that PCIe error reporting feature enabled.
Call synchronize_irq() before freeing IRQ vectors and explicitly free
the other causes interrupt resources and shut down that MSIX interrupt.
Change-ID: Ib88e4536756518a352446da0232189716618ad81
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the user adds an obscene amount of MAC addresses, the driver will run
into the situation where it has too many address requests to fit into a
single PF message. The driver checks for this case, and calculates the
maximum number of messages that it can send. Then it completely ignores
this count and overflows the buffer.
Fix this by checking the address count and bailing out of the loop at
the appropriate time.
Change-ID: If8dcbb04602c75941dc0cd8309065e1de9ca791c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were failing to set the client interface down when we put the VSI
down. Add this call so that the client doesn't get an open called with
no close.
Also remove an un-needed delay. The VF should not be affected at all by
i40e_down.
Change-ID: I1135dffef534bf84e6fed57cf51bcf590e6cfaf7
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that VF RSS is configured by the PF driver, it needs to set the RSS
Hash Enable registers by default. Without this, no packets will be
hashed and they'll all end up on queue 0.
Change-ID: I38e425f40ddb81e3b19a951cfbb939fa5b1123f1
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This function uses the i40e_hw struct all over the place, so why doesn't
it keep a pointer to the struct? Add this pointer as a local variable
and use it consistently throughout the function.
Change-ID: I10eb688fe40909433fcb8ac7ac891cef67445d72
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add functions to enable and disable default VSI on a VEB. This allows
for configuration of limited promiscuous mode specifically for bridging
purposes.
Change-ID: I0cc5bd68b31c500fdff4d47e1f15d50d2739faf4
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
By default, mdiobus_alloc() sets the PHYs to polling mode, but a
pointer size memcpy means that a couple IRQs end up being overwritten
with a value of 0. This means that PHY_POLL is disabled and results
in unpredictable behavior depending on the PHY's location on the
MDIO bus. Remove that memcpy and the now unused phy_irq member to
force the SMSC911x PHYs into polling mode 100% of the time.
Fixes: e7f4dc3536 ("mdio: Move allocation of interrupts into core")
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
trivial fixes to spelling mistakes of the words "excessive collisions"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
trivial fixes to spelling mistakes of the word "descriptors"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous to this patch auto negotiation was reported off although it was
on by default in hardware. This patch reports the correct information to
ethtool and allows the user to toggle it on/off.
Added another parameter to set port proto function in order to pass
the auto negotiation field to the hardware.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new get/set link ksettings and remove get/set settings legacy
callbacks.
This allows us to use bitmasks longer than 32 bit for supported and
advertised link modes and use modes that were previously not supported.
Signed-off-by: Gal Pressman <galp@mellanox.com>
CC: Ben Hutchings <bwh@kernel.org>
CC: David Decotigny <decot@googlers.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MLX5E_50GBASE_SR2 as ETHTOOL_LINK_MODE_50000baseSR2_Full_BIT.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Cc: Ben Hutchings <bwh@kernel.org>
Cc: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a dedicated function to toggle port link. It should be called only
after setting a port register.
Toggle will set port link to down and bring it back up in case that it's
admin status was up.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this mode the moderation timer will restart upon
new completion (CQE) generation rather than upon interrupt
generation.
The outcome is that for bursty traffic the period timer will never
expire and thus only the moderation frames counter will dictate
interrupt generation, thus the interrupt rate will be relative
to the incoming packets size.
If the burst seizes for "moderation period" time then an interrupt
will be issued immediately.
CQE based moderation is off by default and can be controlled
via ethtool set_priv_flags.
Performance tested on ConnectX4-Lx 50G.
Less packet loss in netperf UDP and TCP tests, with no bw degradation,
for both single and multi streams, with message sizes of
64, 1024, 1472 and 32768 byte.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Gil Rockah <gilr@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce an infrastructure for getting/setting private net device
flags.
Currently a 'nop' priv flag is added, following patches will override
the flag will actual feature specific flags.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement set_maxrate ndo.
Use the rate index from the hardware table to attach to channel SQ/TXQ.
In case of failure to configure new rate, the queue remains with
unlimited rate.
We save the configuration on priv structure and apply it each time
Send Queues are being reinitialized (after open/close) operations.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuring and managing HW rate limit tables.
The HW holds a table of rate limits, each rate is
associated with an index in that table.
Later a Send Queue uses this index to set the rate limit.
Multiple Send Queues can have the same rate limit, which is
represented by a single entry in this table.
Even though a rate can be shared, each queue is being rate
limited independently of others.
The SW shadow of this table holds the rate itself,
the index in the HW table and the refcount (number of queues)
working with this rate.
The exported functions are mlx5_rl_add_rate and mlx5_rl_remove_rate.
Number of different rates and their values are derived
from HW capabilities.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates year and company name in the copyright markings in the
be2net source files.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On SR-IOV profiles, when the user connects a Linux Bridge or OVS to a BE3
vport, they suffer the "broadcast/multicast echo" problem. BE3 EVB echoes
broadcast and multicast packets back to PF's vport confusing the
Linux bridge. BE3 relies on the src-mac addr being programmed on the
interface to avoid sending back an echo of a broadcast or multicast packet
on a vPort. When a Linux bridge is connected to a BE3, the mac-addr of the
VM behind the bridge doesn't get configured on the vPort and so echo
cancellation doesn't work.
This patch worksaround this problem by disabling the EVB initially
and re-enabling it *only* when SR-IOV is enabled by the user. For the
driver fix to work, the BE3 FW version must be >= 11.1.84.0.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be2net so far supported creation of RX/TX queues only in pairs.
On configs where rx and tx queue counts are different, creation of only
the lesser number of queues has been supported.
This patch now allows a combination of RX/TX-only channels along with
combined channels. N TX-queues and M RX-queues can be created with the
following cmds:
ethtool -L ethX combined N rx M-N (when N < M)
ethtool -L ethX combined M tx N-M (when M < N)
Setting both RX-only and TX-only channels is still not supported.
It is mandatory to create atleast one combined channel.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EQs available on a function are shared between NIC and RoCE.
The be_max_eqs() macro was so far being used to refer to the max number of
EQs available for NIC. This has caused some confusion in the code. To fix
this confusion this patch introduces a new macro called be_max_nic_eqs()
to refer to the max number of EQs avialable for NIC only and renames
be_max_eqs() to be_max_func_eqs().
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX6UL is a member in i.MX series family, the SOC FEC inherits from
i.MX6SX but removes some IP features, lets define a new type for fec
device.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different i.MX SOC FEC support different features like :
- i.MX6Q/DL FEC does not support AVB and interrupt coalesc
- i.MX6SX/i.MX7D supports AVB and interrupt coalesc
- i.MX6UL/ULL does not support AVB, but support interrupt coalesc
So, add new quirk flag to judge the supported features.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add constants and callback functions for the dwmac on rk3228/rk3229 socs.
As can be seen, the base structure is the same, only registers and the
bits in them moved slightly.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for ddr_timeout during device init.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for private flags for the driver.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch has minor changes for proper ptp info retreival.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for host driver support for new Xaui
interfaces.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds extensive support of statistics for data path,
control path and firmware.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch has new tx/rx interrupt moderation defaults of
count/timer for better throughput and utilisation.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves the order of chip reset while destroying
the resources by postoponing soft reset in destroy resources
function until all queues are removed properly.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds new state so that the ctrl packets are not sent
to firmware during unload time and only rx packets are allowed.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch has firmware image related changes for: firmware
release upon failure, support latest firmware version and
firmware download in 4MB chunks.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This Patch adds tx buffer handling to Napi along with RX
traffic. Also separate spinlocks are introduced for handling
iq posting and buffer reclaim so that tx path and tx interrupt
do not compete against each other.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds supports for Vlan filtering for liquidio driver.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for vlan offloads for the driver and
receive header structures are also modified appropriately. Also
requestID will not be used in reveive header any more.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch increases the limits of soft command buffer size and
num command buffers. This patch also has changes for queue macros
and limit related changes for new chips.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue comes when there are multiple threads attempting to use the
mailbox facility at the same time. The issue is the for the Virtual
Function Driver, the only way to get the Virtual Interface statistics
is to issue mailbox commands to ask the firmware for the VI Stats.
And, because the VI Stats command can only retrieve a smallish number of
stats per mailbox command, we have to issue three mailbox commands in quick
succession. When ethtool or netstat command to get interface stats and
interface up/down is run in a loop for every 0.1 sec, we observed
mailbox collisions. And out of the two commands one would fail with
the present code, since we don't queue the second command.
To overcome the above issue, added a queue to access the mailbox.
Whenever a mailbox command is issued add it to the queue. If its at the
head issue the mailbox command, else wait for the existing command to
complete. Usually command takes less than a milli-second to complete.
Also timeout from the loop, if the command under execution takes
long time to run.
In reality, the number of mailbox access collisions is going to be very
rare since no one runs such abusive script.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for configuring the device tx/rx coalescing
timeout values in the order of micro seconds. It also adds APIs for
upper layer drivers for reading/updating the coalescing values.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for reading and updating priority flow
control (PFC) attributes in the driver via netlink.
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dual MAC devices don't necessarily have both MACs wired up, so ignore
those that are disabled.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we do have pci_request_mem_regions() and pci_release_mem_regions()
at hand, use it in the ethernet drivers.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
CC: Jay Cliburn <jcliburn@gmail.com>
CC: Chris Snook <chris.snook@gmail.com>
CC: David S. Miller <davem@davemloft.net>
Now that we do have pci_request_mem_regions() and pci_release_mem_regions()
at hand, use it in the Intel ethernet drivers.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: David S. Miller <davem@davemloft.net>
Currently, the SRQ API uses the obsolete mlx5_*_srq_mbox_{in,out}
structs which limit the ability to pass the SRQ attributes between
net and IB parts of the driver.
This patch changes the SRQ API so as to use auto-generated structs
and provides a better way to pass attributes which will be in use by
coming features.
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In order to support RSS QPs, we need to create Ethernet based objects.
This is done by create_rq, destroy_rq, create_rqt and destroy_rqt
mlx5_core functions. We export these functions.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This allows a clean shutdown, even if some netdev clients do not
release their reference from this netdev. It is enough to release
the HW resources only as the kernel is shutting down.
Fixes: 2ba5fbd62b ('net/mlx4_core: Handle AER flow properly')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify mlx4_en_vlan_rx_[add/kill]_vid to return error value in case of
failure.
Fixes: 8e586137e6 ('net: make vlan ndo_vlan_rx_[add/kill]_vid return error value')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For debug purposes, it's useful to know the order in which the driver
responds to changes in the topology of its upper devices.
Add debug prints to signal these events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are situations in which a vPort is destroyed while still holding
references to device's resources such as FIDs and FDB records. This can
happen, for example, when a VLAN device is deleted while still being
bridged.
Instead of trying to make sure vPort destruction is invoked when it no
longer uses device's resources, just free them upon destruction. This
simplifies the code, as we no longer need to take different situations
into account when events are received - cleanup is taken care of in one
place.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FDB entries are learned using {Port / LAG ID, FID} and therefore should
be flushed whenever a port (vPort) leaves its FID (vFID).
However, when the bridge port is a LAG device (or a VLAN device on top),
then FDB flushing is conditional. Ports removed from such LAG
configurations must not trigger flushing, as other ports might still be
members in the LAG and therefore the bridge port is still active.
The decision whether to flush or not was previously computed in the
netdevice notification block, but in order to flush the entries when a
port leaves its FID this decision should be computed there.
Strip the notification block from this logic and instead move it to one
FDB flushing function that is invoked from both the FID / vFID leave
functions.
When port isn't member in LAG, FDB flushing should always occur.
Otherwise, it should occur only when the last port (vPort) member in the
LAG leaves the FID (vFID).
This will allow us - in the next patch - to simplify the cleanup code
paths that are hit whenever the topology above the port netdevs changes.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all vPorts will have FIDs assigned to them, so make sure functions
first test for FID presence.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As previously explained, not all vPorts will be assigned FIDs, so instead
of returning the FID index of a vPort, return a pointer to its FID
struct. This will allow us to know whether it's legal to access the
vPort's FID parameters such as index and device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When L3 interfaces will be introduced a vPort won't necessarily have a
FID assigned to it. This can happen if it's not member in a bridge (in
which case it's assigned a vFID) or doesn't have an IP address (in which
case it's assigned an rFID).
Therefore, instead check the VID parameter to test whether a port is a
vPort or not.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a very similar way to the vFIDs, make the first 4K FIDs - used in the
VLAN-aware bridge - use the new FID struct.
Upon first use of the FID by any of the ports do the following:
1) Create the FID
2) Setup a matching flooding entry
3) Create a mapping for the FID
Unlike vFIDs, upon creation of a FID we always create a global
VID-to-FID mapping, so that ports without upper vPorts can use it
instead of creating an explicit {Port, VID} to FID mapping.
When a port leaves a FID the reverse is performed. Whenever the FID's
reference count reaches zero the FID is deleted along with the global
mapping.
The per-FID struct will later allow us to configure L3 interfaces on top
of the VLAN-aware bridge.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a vPort is created or when it joins a bridge we always do the same
set of operations:
1) Create the vFID, if not already created
2) Setup flooding for the vFID
3) Map the {Port, VID} to the vFID
When a vPort is destroyed or when it leaves a bridge the reverse is
performed.
Encapsulate the above in join / leave functions and simplify the code.
FIDs and rFIDs will use a similar set of functions.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we had a dedicated struct only for vFIDs, but before
introducing support for L3 interfaces we need to make it generic and
use it for all three types of FIDs:
1) FIDs - 0..4K-1, used for the VLAN-aware bridge
2) vFIDs - 4K..15K-1, used for VLAN-unaware bridges
3) rFIDs - 15K..16K-1, used to direct traffic to / from the router in
the device. Will be introduced later in the series.
The three types of L3 interfaces - Router InterFaces, RIFs - that will
be introduced correspond to the three types of FIDs and are configured
using them. Therefore, we'll need to store the links between them as
well as a reference count on the underlying FID, so that the
corresponding RIF will be destroyed when it reaches zero.
Note that the lower 0.5K vFIDs are currently used for for non-bridged
netdevs, so that traffic could be flooded to the CPU port. However, when
rFIDs will be introduced we'll no longer need these and they too will be
used for VLAN-unaware bridges.
Make the vFID struct generic by renaming it and some of its fields. FIDs
will be converted to use it later in the series.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a FID index instead of vFID and ease the transition towards a
generic FID struct.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A FID used by a vPort (vFID, but also rFID later in the series) is
always mapped using {Port, VID} and not only VID as with the 4K FIDs of
the VLAN-aware bridge.
Instead of specifying all the arguments each time, just wrap this
operation using a dedicated function and simplify the code.
As before, the function takes FID as its argument in preparation for a
generic FID struct.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code and use only one function for vFID creation /
destruction.
Unlike before, the function receives a FID index as its argument and not
a vFID index. Instead of passing 0, now one would need to pass 4K, which
is the first vFID.
This is the first step in creating a generic FID struct that will be
used for all three types of FIDs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In all call sites 'only_uc' is set to false, so strip it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a macro to do this kind of declarations, so use it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We hold a reference count on the number of ports member in the
VLAN-aware bridge, as we only support one.
Instead of always incrementing / decrementing the reference count after
joining / leaving the bridge, simply do this accounting in the join /
leave functions.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The argument 'br_dev' is never used, so remove it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When responding to unlinking CHANGEUPPER notifications we shouldn't
return any value, as it's not checked by upper layers.
In addition, there's nothing the driver can do in case of failure, so it
should simply continue and try to free as much resources as possible and
not stop on first error.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of checking for a condition and then issue the warning, just do
it in one go and simplify the code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When upper device of a VLAN device changes we already made sure it's
a bridge device in PRECHANGEUPPER, so no need to check it's a master
device in CHANGEUPPER.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port netdev is put under LAG it cannot have VLAN upper devices,
so forbid that. The LAG device itself can have VLAN upper devices.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently only support the following upper devices for port netdevs:
1) Bridge
2) LAG (bond / team)
3) VLAN
Any other device is forbidden, so return an error.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of checking the error value and returning NOTIFY_BAD, just use
notifier_from_errno() and simplify the code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enable/disable tso, the driver tries to access the hardware register,
but this operation will cause the port unavalible when there is traffic.
This patch tries to enable TSO when initialize, then control tso through
TSE bit in transmit descriptor.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default coalesce timeout is 3us, which is will cause CPU
usage is too high. This patch change it to 50us in order to reduce
CPU usage and the value makes sure network latency also meets requirement.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default sbm config parameter leaves little buffer when there is heavy
traffic, which will cause packets drop. This patch changes them to make
enough buffers for handling packets.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hns_nic_poll_rx_skb alloc skb fail, it will break receive cycle and
read new fbd_num to start new receive cycle. It recomputes cycle num is
fbd_num minus clean_count, actually this cycle num is too big because
it drop out receive cycle. It brings about the port unavailable.
So we will goto out when alloc skb fail to fix this bug.
Signed-off-by: Jun He <hjat2005@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default driver sets anchor led bit to 0 when link down,
actually, the anchor bit should be set to 1, so fixes it when
link status is down.
Secondly, change the return value of cpld_set_led_id to 0, which
means leave the cpld to control led blink frequece other than the
driver itself.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When network interface is enabled, the ring enable operation is
conducted twice. This patch deletes the redundancy code of ring enable,
and integrates hnae_ae_ops.toggle_queue_status other functions to
hns_ae_start.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds get_coalesce_range api for hns, it shows
range of coalesce usecs and frames that can be set on
this interface.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver stores the high bit value of tcam data register
to the tcam data low element, stores the low bit value of tcam data
register to tcam data high element, this patch fixes this bug.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds spin lock for tcam table operation,
there maybe a race condition happens when more than
one thread try to change the tcam talbe entries.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For SoC hip06, PFC pause handled in dsaf, while hip05 in XGMAC,
so change the statistics of pfc pause in dsaf and remove the old
pfc pause frame statistics.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For debug-ports,there are two non-synchronized processes:
Speed-Auto-Negotiation and Link-Update-Status. The two
processes are towed by two different state machines.
Bond reads the speed when link up, but the speed maybe
not update the right value at that time.That make for bond's
wrong speed. Thus only one state machine should be used and
if phy_state_machine is used, it does not need to do
hns_nic_update_link_status().
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When run ethtool cmd(ethtool -t ethx) again and again for a long
time, it will be probabilistically fail. The PHYs' registers may
be on different pages, so it must be switch to the right page
before setting PHYs' registers.
And __lb_up() calls phy_start() to startup the PHYs device, but
this function may change Copper Control Register(Page 0, Register 0)
to an other value. It would cause phy loopback test fail. if we
remove phy_start(), we have to remove the relative phy_stop(),
phy_disconnect() when doing phy loopback to keep the phy stay in
right status.
Reported-by: hejun <hjat2005@huawei.com>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Hilink3 and Hilink4 use the same xge training and xge u adaptor for
HNSv2, it needs to select which Hilink to be set before relative serdes
being configed. The hilink_access_sel is the register to do that.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error info should be printed as "set mask to 64bit fail!" instead of
"set mask to 32bit fail!" in dma_set_mask_and_coherent().
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses devm_ioremap_resource, it will unmap the map
automatically, remove the unnecessary the resource free.
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The annotation info for hns_nic_reset_subtask() should be
"for resetting subtask" instead of "for resetting suntask".
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS receives a packet without doing anything, but it should call
skb_reset_mac_header() to initialize the header before using
eth_hdr().
Fixes: 0d6b425a37
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For service port, hns dsaf v1 support to close tx_pause.
However, the port will be invalid when it run command
ethtool to close tx_pause. This patch will fix it.
Signed-off-by: Qianqian Xie <xieqiaqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bit fileds of PPE reset register are different between HNS v1 and
HNS v2, but the current procedure just only match HNS v1. Here is a
patch to fix it.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'MODULE_FIBER' value replaced several other FIBER values
in newer management firmware images, so existing code would
fail to properly reflect its mode.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver has 2 sets of entries for handling ramrod configurations
toward firmware - a regular pre-allocated set of entires and a
possible 'unlimited' list of additional pending entries.
In most scenarios the 'unlimited' list would not be used, but
when it does the handling of the ramrod completion doesn't
properly handle the release of the entry.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several user APIs can cause driver to perform an inner-reload.
Currently, doing this would cause the HW/FW statistics of the
adapter to reset, which isn't the expected behavior [statistics
should only reset on explicit unloads].
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Internal loopback in driver is based on two things - first
is the willingness of transmitter to use it [in case of VFs,
this can be forced based on VEPA/VEB] and secondly on another
vport classification configuration which should match the
packet's destination.
Current code allows non-linux VFs to configure a 'promisc'
mode on Tx, meaning all traffic sent by VF would be loopbacked
internally by firmware; This isn't considered a valid mode and
as such should be prevented by PF.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When no vlan filter is configured, firmware has a configurable
default on whether to pass only untagged packets or all packets
regardless of their tagging. Driver currently doesn't set this
field in the necessary ramrod, causing the default to always be
'receive all'.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conversion to the 64-bit time based ptp methods left two instances
of 'struct timespec' in place. This is harmless because 64-bit
architectures define timespec64 as timespec, and this driver is
not used on 32-bit machines.
However, using 'struct timespec64' directly is obviously the right
thing to do, and will help us remove 'struct timespec' in the future.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b9acf24f77 ("ptp: tilegx: convert to the 64 bit get/set time methods.")
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop the SW TX counter from counting the TX header bytes
since they are not being sent out.
Fixes: e577516b9d ("mlxsw: Fix use-after-free bug in mlxsw_sx_port_xmit")
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop the SW TX counter from counting the TX header bytes
since they are not being sent out.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason in rx_descs property because davinici_cpdma
driver splits pool of descriptors equally between tx and rx channels.
That is, if number of descriptors 256, 128 of them are for rx
channels. While receiving, the descriptor is freed to the pool and
then allocated with new skb. And if in DT the "rx_descs" is set to
64, then 128 - 64 = 64 descriptors are always in the pool and cannot
be used, for tx, for instance. It's not correct resource usage,
better to set it to half of pool, then the rx pool can be used in
full. It will not have any impact on performance, as anyway, the
"redundant" descriptors were unused.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable i was declared but was never used and we were getting a
build warning for that.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change replaces the network device operations for adding or removing a
VXLAN port with operations that are more generically defined to be used for
any UDP offload port but provide a type. As such by just adding a line to
verify that the offload type is VXLAN we can maintain the same
functionality.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch goes through and combines the notifiers for VXLAN and GENEVE
into a single function for each action. So there is now one combined
function for getting ports, one for adding the ports, and one for deleting
the ports.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change replaces the network device operations for adding or removing a
VXLAN port with operations that are more generically defined to be used for
any UDP offload port but provide a type. As such by just adding a line to
verify that the offload type is VXLAN we can maintain the same
functionality.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change replaces the network device operations for adding or removing a
VXLAN port with operations that are more generically defined to be used for
any UDP offload port but provide a type. As such by just adding a line to
verify that the offload type is VXLAN we can maintain the same
functionality.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change replaces the network device operations for adding or removing a
VXLAN port with operations that are more generically defined to be used for
any UDP offload port but provide a type. As such by just adding a line to
verify that the offload type is VXLAN we can maintain the same
functionality.
In addition I updated the socket address family check so that instead of
excluding IPv6 we instead abort of type is not IPv4. This makes much more
sense as we should only be supporting IPv4 outer addresses on this
hardware.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change replaces the network device operations for adding or removing a
VXLAN port with operations that are more generically defined to be used for
any UDP offload port but provide a type. As such by just adding a line to
verify that the offload type is VXLAN we can maintain the same
functionality.
In addition I updated the socket address family check so that instead of
excluding IPv6 we instead abort of type is not IPv4. This makes much more
sense as we should only be supporting IPv4 outer addresses on this
hardware.
The last change is that I pulled the rtnl_lock/unlock into the conditional
statement for IXGBE_FLAG2_VXLAN_REREG_NEEDED. The motivation behind this
is to avoid unneeded bouncing of the mutex which will just slow down the
handling of this call anyway.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch goes through and combines the notifiers for VXLAN and GENEVE
into a single function for each action. So there is now one combined
function for getting ports, one for adding the ports, and one for deleting
the ports.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change replaces the network device operations for adding or removing a
VXLAN port with operations that are more generically defined to be used for
any UDP offload port but provide a type. As such by just adding a line to
verify that the offload type if VXLAN we can maintain the same
functionality.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change replaces the network device operations for adding or removing a
VXLAN port with operations that are more generically defined to be used for
any UDP offload port but provide a type. As such by just adding a line to
verify that the offload type if VXLAN we can maintain the same
functionality.
I have also gone though and removed the BE2NET_VXLAN config option since it
no longer relies on the VXLAN code anyway.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port number for GENEVE is hard coded into the bnxt driver. This is the
kind of thing we want to avoid going forward. For now I will integrate
this back into the port notifier so that we can change the GENEVE port
number if we need to in the future.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ends up doing several things. First it updates the driver to
make use of the new unified UDP tunnel offload notifier functions. In
addition I updated the code so that we can work around the bits that were
checking for if VXLAN was enabled since we are now using a notifier based
setup.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch goes through and combines the notifiers for VXLAN and GENEVE
into a single function for each action. So there is now one combined
function for getting ports, one for adding the ports, and one for deleting
the ports.
I also went through and dropped the BNX2X VXLAN and GENEVE specific build
flags.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modern C standards expect the '__inline__' keyword to come before the return
type in a declaration, and we get a warning for this with "make W=1":
drivers/net/ethernet/freescale/gianfar.c:2278:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were using an incorrect define to get the irq vector number.
NFP_NET_CFG_LSC is a control BAR offset, LSC interrupt vector
index is called NFP_NET_IRQ_LSC_IDX. For machines with less
than 30 CPUs this meant that we were disabling/enabling IRQ 0.
For bigger hosts we were just playing with the 31st RX/TX
interrupt.
Fixes: 0ba40af963 ("nfp: move link state interrupt request/free calls")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get a warning for tlan_handle_tx_eoc when building with "make W=1"
drivers/net/ethernet/ti/tlan.c: In function 'tlan_handle_tx_eoc':
drivers/net/ethernet/ti/tlan.c:1647:59: error: parameter 'host_int' set but not used [-Werror=unused-but-set-parameter]
static u32 tlan_handle_tx_eoc(struct net_device *dev, u16 host_int)
This is harmless, but removing the unused assignment lets us avoid
the warning with no downside.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get a warning for qlcnic_83xx_get_mac_address when building with
"make W=1":
drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c: In function 'qlcnic_83xx_get_mac_address':
drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c:2156:8: error: parameter 'function' set but not used [-Werror=unused-but-set-parameter]
Clearly this is harmless, but there is also no point for setting
the variable, so we can simply remove the assignment.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx4e driver does not support more than one port for VXLAN offload. As
such expecting the hardware to offload other ports is invalid since it
appears the parsing logic is used to perform Tx checksum and segmentation
offloads. Use the vxlan_port number to determine in which cases we can
apply the offload and in which cases we can not.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building with -Wextra, we get a harmless warning from the
EFX_EXTRACT_OWORD32 macro:
ethernet/sfc/farch.c: In function 'efx_farch_test_registers':
ethernet/sfc/farch.c:119:30: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
ethernet/sfc/farch.c:124:144: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
ethernet/sfc/farch.c:124:392: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
ethernet/sfc/farch.c:124:731: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
The macro and the caller are both correct, but we can avoid the
warning by changing the index variable to a signed type.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When suspending the machine, do not shutdown the external PHY by cutting
its regulator in the mac platform driver suspend code if Wake-on-Lan is enabled,
else it cannot wake us up.
In order to do this, split the suspend/resume callbacks from the
init/exit callbacks, so we can condition the power-down on the lack of
need to wake-up from the LAN but do it unconditionally when unloading the
module.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let the stmmac platform drivers provide dedicated suspend and resume
callbacks rather than always re-using the init and exits callbacks.
If the driver does not provide the suspend or resume callback, we fall
back to the old behavior trying to use exit or init.
This allows a specific platform to perform only a partial power-down on
suspend if Wake-on-Lan is enabled but always perform the full shutdown
sequence if the module is unloaded.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If vPort has VLAN_RESTRICT flag, VLAN tagged traffic will not be
delivered without corresponding Rx filters which may be proxied to and
moderated by hypervisor.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If should be done after net_dev->hw_features initialization, to keep the
feature there to be able to enable it later using ethtool.
VLAN filtering is enforced and fixed if vPort requires usage of VLAN
filters to receive tagged traffic.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If it is not supported we simply disable the feature.
For the feature to work we need firmware filter support for
OUTER_VID + LOC_MAC and for OUTER_VID + LOC_MAC_IG.
The low-latency firmware can match on OUTER_VID + LOC_MAC but not on
OUTER_VID + LOC_MAC_IG.
For the capture packet firmware it is the other way around.
Only the full-feature variant can match on both combinations.
Incorporates a fix by Andrew Rybchenko <Andrew.Rybchenko@oktetlabs.ru>
in the net_dev->[hw_]features handling.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filter match flags are not unique criteria to be mapped to priority
because of both unknown unicast and unknown multicast are mapped to
LOC_MAC_IG. So, local MAC is required to map filter to priority.
MCDI filter flags is unique criteria to find filter priority.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nearly every time we call efx_ef10_filter_remove_unsafe, we first check
for EFX_EF10_FILTER_ID_INVALID, in which case we do nothing. So move
that check into the function, simplifying all the call sites.
Also, change the return type to void, since none of the callers check it.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to enslave an SFC interface to a bond the following BUG_ON was
hit:
kernel BUG [in ef10.c]!
CPU: 0 PID: 4383 Comm: ifenslave Tainted: G
...
Call Trace:
efx_ef10_filter_add_vlan+0x121/0x180 [sfc]
efx_ef10_filter_table_probe+0x2a2/0x4f0 [sfc]
efx_ef10_set_mac_address+0x370/0x6d0 [sfc]
efx_set_mac_address+0x7d/0x120 [sfc]
dev_set_mac_address+0x43/0xa0
bond_enslave+0x337/0xea0 [bonding]
This comes from function efx_ef10_filter_vlan_sync_rx_mode.
To solve the bug we ensure the mac_lock is taken before calling
efx_ef10_filter_add_vlan. But to avoid a priority inversion mac_lock must
be taken before filter_sem.
To satisfy these requirements we end up taking mac_lock in
efx_ef10_vport_set_mac_address, efx_ef10_set_mac_address,
efx_ef10_sriov_set_vf_vlan and efx_probe_filters.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supports HW VLAN filtering, en/disabled using ethtool.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now it contains dummy VLAN entry with unspecified VID only.
The entry is used for the case when HW VLAN filtering is not used.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These flags are built when address cache is updated.
The information will be required when VLAN filtering is added and address
cache is used without re-sync.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a step to support VLAN filtering in HW.
Until then, there is only one struct efx_ef10_filter_vlan per struct
efx_ef10_filter_table, with no VLAN information yet.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is required to remove setting of filter IDs to invalid from multicast
and unicast addresses caching functions.
Add initialization to invalid when filter table is created.
Add paranoid checks to track consistency.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on a patch by Andrew Rybchenko <Andrew.Rybchenko@oktetlabs.ru>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It allows to change set of fixed features on datapath reset.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is used for EF10 only and logically belongs to EF10 filter table state.
It is OK that it is reset to false on filter table recreation since all
filters are removed on destruction.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for new instruction header for octeon2/octeon3(ih) and
corresponding changes.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch decoupled the firmware side ifidx and host side interface
number. It also has some minor name change for linkinfo sturct field.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is for new driver/firmware control command structure
(octnic_packet_params and octnic_cmd_setup ) and resultant code changes.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to refactor packet size calculations to support PTP enabled
for 66xx and 68xx cards and also other cards that do not support PTP.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add page based buffers for receive side descriptors of
the driver and separate free routines for rx and tx buffers.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to allocate rx queue's memory based on numa node and also use
page based buffers for rx traffic improvements.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to allocate and manage scatter gather lists per
input queue(iq's) and remove queue's interdependence.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to allocate the input queues based on Numa node in tx path
and queue mapping changes based on the mapping info provided by firmware.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to resolve the double free issue by checking proper return
values from soft command.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if interface is in Promiscuous mode/Allmulti mode synchronize
MAC addresses.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement callback in the driver for the new PCI bus driver
interface that allows the user to enable/disable SR-IOV
virtual functions in a device via the sysfs interface.
Deprecate module parameter used to configure SRIOV
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When is_kdump_kernel() is true, Forcing cxgb4 driver as Master so we can
reinitialize the Firmware/Chip. Also reduce memory usage by disabling
offload.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DT support to the Cirrus Logic CS89x0 driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maciej Żenczykowski reported lockdep warning a spinlock
was not registered before being held in mlx4_cmd_wake_completions()
cmd.context_lock initialization is not at the right place.
1) mlx4_cmd_use_events() can be called multiple times.
Calling spin_lock_init() on a live spinlock can lead
to hangs.
2) mlx4_cmd_wake_completions() can be called while lock
has not been initialized.
Lockdep complains, and current logic is not race prone.
It seems better to move the initialization earlier in
mlx4_load_one()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Maciej Żenczykowski <maze@google.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the patchset about adding support of ACPI (commit id is 6343488)
being applied, HNS does not depend on OF. It depends on OF or ACPI, so
the Kconfig file needs to be updated.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To fully support 25G and 50G link settings.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some cards do not support autoneg. The current code does not prevent the
user from enabling autoneg with ethtool on such cards, causing confusion.
Firmware provides the autoneg capability information and we just need to
store it in the support_auto_speeds field in bnxt_link_info struct.
The ethtool set_settings() call will check this field before proceeding
with autoneg.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add bnxt_gro_func_5731x() to handle GRO packets for this chip. The
completion structures used in the new chip have new data to help determine
the header offsets. The offsets can be off by 4 if the packet is an
internal loopback packet (e.g. from one VF to another VF). Some additional
logic is added to adjust the offsets if it is a loopback packet.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer chips require different logic to handle GRO packets. So refactor
the code so that we can call different functions depending on the chip.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define all the supported chip numbers and chip categories. Store the
chip_num returned by firmware. If the call to get the version and chip
number fails, we should abort.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NPAR type is read from bnxt_hwrm_func_qcfg. Do not allow changing link
parameters if in NPAR mode sinc ethe port is shared among multiple
partitions. The link parameters are set up by firmware.
Signed-off-by: Satish Baddipadige <sbaddipa@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the VF driver gets this event, the VF configuration has changed (such
as default VLAN). The VF driver will initiate a silent reset to pick up
the new configuration.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a default VLAN is added to the VF, the VF driver needs to reset to
pick up the default VLAN ID. We can use the same tx timeout reset logic
to do that, without the debug output. This new function, with the
silent parameter to suppress debug output will now serve both purposes.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF can setup a default VLAN for a VF. The default VLAN tag is
automatically inserted and stripped without the knowledge of the
stack running on the VF. The VF driver needs to know that default
VLAN is enabled as VLAN acceleration on the RX side is no longer
supported. Call netdev_update_features() to fix up the VLAN features
as necessary. Also, VLAN strip mode must be enabled to strip out
the default VLAN tag.
Only allow VF default VLAN to be set if the firmware spec is >= 1.2.1.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move the enic driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 26c5f03 uses a new skb allocator to avoid the RFD overflow
issue.
But from debugging without datasheet, we found the error always
happen when the DMA RX address is set to 0x....fc0, which is very
likely to be a HW/silicon problem.
So one idea is instead of adding a new allocator, why not just
hitting the right target by avaiding the error-prone DMA address?
This patch will actually
* Remove the commit 26c5f03
* Apply rx skb with 64 bytes longer space, and if the allocated skb
has a 0x...fc0 address, it will use skb_resever(skb, 64) to
advance the address, so that the RX overflow can be avoided.
In theory this method should also apply to atl1c driver, which
I can't find anyone who can help to test on real devices.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=70761
Signed-off-by: Feng Tang <feng.tang@intel.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Tested-by: Ole Lukoie <olelukoie@mail.ru>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason to destroy channels that are destroyed while
cpdma_ctlr destroy. In this case no need to remember how much
channels where created and destroy them by one, as cpdma_ctlr
destroys all of them.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since msleep is based on jiffies the PHY reset could take longer
than expected. So use msleep for values greater than 20 msec otherwise
usleep_range.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i.MX6 Q/DL has an erratum (ERR006687) that prevents the FEC from
waking the CPUs when they are in wait(unclocked) state. As the hardware
workaround isn't applicable to all boards, disable the deeper idle state
when the workaround isn't present and the FEC is in use.
This allows to safely run a kernel with CPUidle enabled on all i.MX6
boards.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: David S. Miller <davem@davemloft.net> (for network changes)
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Commit 7f854420fb
("phy: Add API for {un}registering an mdio device to a bus.")
broke PHY detection on this driver with a copy-paste bug:
The code is looking 32 times for a PHY at address 0.
Fixes ethernet on AMD DB1100/DB1500/DB1550 boards which have
their (autodetected) PHYs at address 31.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7f854420fb
("phy: Add API for {un}registering an mdio device to a bus.")
broke PHY detection on this driver with a copy-paste bug:
The code is looking 32 times for a PHY at address 0.
Fixes ethernet on AMD DB1100/DB1500/DB1550 boards which have
their (autodetected) PHYs at address 31.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code checks if the queue should be stopped because we are below the
threshold of free descriptors only to check if it should be started again.
If we do end up in a state where we are at the threshold limit, it makes
more sense to just stop the queue and wait for the next IRQ to trigger the
TX housekeeping again. There is no rush in enqueuing the next packet, it
needs to wait for all the others in the queue to be dispatched first
anyway.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code unconditionally wakes up the queue at the end of each
tx_poll action. Change the code to only wake up the queues if any of
them have actually been stopped before.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX ring setup has an off by one error causing it to not utilise all
descriptors. This has the side effect that we need to reset the next
pointer at runtime to make it work. Fix the off by one and remove the
code fixing the ring at runtime.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
During stress testing, after reducing the threshold value, we have seen
TX timeouts that were caused by the watchdog_timeo value being too low.
Increase the value to 5 * HZ which is a value commonly used by many other
drivers.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic to calculate the threshold value for stopping the TX queue is
bad. Currently it will always use 1/2 of the rings size, which is way too
much. Set the threshold to MAX_SKB_FRAGS. This makes sure that the queue
is stopped when there is not enough room to accept an additional segment.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code only disables those IRQs that we will later use. To
ensure that we have a predefined state, we really want to disable all IRQs.
Change the code to disable all IRQs to achieve this.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QDMA engine can fail to update the register pointing to the next TX
descriptor if this bit does not get set in the QDMA configuration register.
Not setting this bit can result in invalid values inside the TX rings
registers which will causes TX stalls.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two places inside mtk_poll_rx where rx_dropped is not being
incremented properly. Fix this by adding the missing code to increment
the counter.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lookup of the tx_buffer in the error path inside mtk_tx_map() uses the
wrong descriptor pointer. This looks like a copy & paste error. Change the
code to use the correct pointer.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scratch memory gets allocated in mtk_init_fq_dma() but the corresponding
code to free it is missing inside mtk_dma_free() causing a memory leak.
With this patch applied, we can run ifconfig up/down several thousand
times without any problems.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code fails to check if the scratch memory was properly allocated. Add
this check and return with an error if the allocation failed.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/sched/act_police.c
net/sched/sch_drr.c
net/sched/sch_hfsc.c
net/sched/sch_prio.c
net/sched/sch_red.c
net/sched/sch_tbf.c
In net-next the drop methods of the packet schedulers got removed, so
the bug fixes to them in 'net' are irrelevant.
A packet action unload crash fix conflicts with the addition of the
new firstuse timestamp.
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_workqueue replaces deprecated create_workqueue().
A dedicated workqueue has been used since the workqueue
mlxsw_wq is used for FDB notif. processing with workitems that are
involved in normal device operation && because it's a network device
which can be depended upon during memory reclaim.
Workitems &trans->timeout_dw and &mlxsw_sp->fdb_notify.dw,
map to mlxsw_sp_fdb_notify_work (processes FDB notifications from the
underlying device and resolves the netdev to which the entry points to
and notifies the bridge using the switchdev notifier) and
mlxsw_emad_trans_timeout_work (provides async EMAD register access)
respectively. They require forward progress under memory pressure and
hence, WQ_MEM_RECLAIM has been set.
Since there are only a fixed number of work items, explicit concurrency
limit is unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_workqueue replaces deprecated create_workqueue().
A dedicated workqueue has been used since the workitem viz
(&lio->txq_status_wq.wk.work which maps to octnet_poll_check_txq_status)
is involved in a brief poll routine for checking transmit queue status
and is an intergral part of normal device operation.
WQ_MEM_RECLAIM has been set to guarantee forward progress under memory
pressure, which is a requirement here.
Since there are only a fixed number of work items, explicit concurrency
limit is unnecessary.
flush_workqueue is unnecessary since destroy_workqueue() itself calls
drain_workqueue() which flushes repeatedly till the workqueue
becomes empty.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4 RSS is limited to spread incoming packets to a power of two number
of queues.
An uniformly distibuted traffic would be split on queues 0 to N-1, N
being a power of two, each queue having a 1/N weight.
If number of RX queues is not a power of two, upper RX queues do not
receive traffic.
ethtool -x is lying, because it pretends some queues have higher weight.
Before patch:
lpaa24:~# ethtool -L eth1 rx 24
lpaa24:~# ethtool -x eth1
RX flow hash indirection table for eth1 with 24 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 8 9 10 11 12 13 14 15
16: 0 1 2 3 4 5 6 7
RSS hash key:
e0:7c:3a:89:07:55:b6:58:69:cc:f4:e5:24:62:e3:25:88:6c:42:5b:d2:cb:9a:d2:e0:06:e1:dc:f9:09:a1:89:0f:a0:30:43:73:6f:0c:b6
If this information was correct, user space tools could expect queues 0
to 7 to receive twice more traffic than queues 8 to 15
After patch :
lpaa24:~# ethtool -L eth1 rx 24
lpaa24:~# ethtool -x eth1
RX flow hash indirection table for eth1 with 24 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 8 9 10 11 12 13 14 15
RSS hash key:
da:7b:09:60:f1:ac:67:b4:d0:72:d4:ec:a2:e5:80:0a:ad:50:22:1a:f8:f9:66:54:5f:22:45:c3:88:f4:57:82:c1:c1:90:ed:70:cb:40:ce
lpaa24:~# ethtool -X eth1 equal 8
lpaa24:~# ethtool -x eth1
RX flow hash indirection table for eth1 with 24 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 0 1 2 3 4 5 6 7
RSS hash key:
da:7b:09:60:f1:ac:67:b4:d0:72:d4:ec:a2:e5:80:0a:ad:50:22:1a:f8:f9:66:54:5f:22:45:c3:88:f4:57:82:c1:c1:90:ed:70:cb:40:ce
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Maciej Żenczykowski <maze@google.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Cc: Wei Wang <weiwan@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac4_set_umac_addr() takes a struct mac_device_info as
the first parameter, but is being passed a ioaddr instead from
dwmac4_set_filter(). Fix the warning/bug by changing the first
parameter.
drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c:159:46: warning: incorrect type in argument 1 (different address spaces)
drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c:159:46: expected struct mac_device_info *hw
drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c:159:46: got void [noderef] <asn:2>*ioaddr
Note, only compile tested this as do not have any
hardware with it in.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a few netdev statistics to report transmitted and received bytes and
packets and a few obvious errors.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read the statistics from the BGMAC's builtin MAC and return them to
user-space using the standard ethtool helpers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing different helpers to be utilized against
network devices created by the bgmac driver, make sure that we bind the
net_device with core->dev.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I am not sure mlx4_en_netpoll() is doing anything useful right now.
mlx4 has different NAPI structures for RX and TX, and netpoll only wants
to drain TX queues.
Lets schedule NAPI polls on TX, not RX.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Blue flame is a latency enhancement feature that allows the driver to
write the packet data directly to the NIC's registers thus making the
read of the packet data from host memory redundant.
We maintain a quota for the blue flame which is reloaded whenever we
identify that the hardware is processing send requests and processes
them fast enough so by the time we post the next send request it was
able to process all the pending ones. This indicates that the hardware
is capable of processing more blue flame requests efficiently. The blue
flame quota is decremented whenever we send using blue flame.
The current code erroneously clears the budget if we did not use blue
flame for the current post send operation and we fix it here.
Fixes: 88a85f99e5 ('net/mlx5e: TX latency optimization to save DMA reads')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation copies the flow of ndo_stop instead of
calling it explicitly, Fixed it.
Fixes: 5fc7197d3a ("net/mlx5: Add pci shutdown callback")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the mc_promisc flag also in the case of adding new mc address to
existing allmulti vport.
Fixes: a35f71f27a ('net/mlx5: E-Switch, Implement promiscuous rx modes vf request handling')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In RoCE, the RDMA-CM needs the node guid to establish connection
between nodes.
Today, the node guid exposed to mlx5 Ethernet VFs is zero, therefore
RDMA-CM on the VF is broken.
Whenever the administrator sets a MAC for a VF, derive the node guid
from it and set it as well in the following way:
MAC: e4:1d:2d:b3:f4:01 -> node_guid: e4:1d:2d:ff:fe:b3:f4:01
Fixes: 77256579c6 ('net/mlx5: E-Switch, Introduce Vport...')
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reorder vport enable flow to mark the vport as enabled before calling
the vport change handler which was modified to handle the case for
when vport is not enabled.
This fixes the case for when the PF netdev is open before sriov is
enabled, once sriov is enabled at esw_enable_vport,
esw_vport_change_handle_locked didn't read the PF context since it
thought the PF vport was not enabled.
When we enable the vport, arming for events is not required anymore,
since it's done on the vport change handle
Fixes: 586cfa7f1d ('net/mlx5: E-Switch, Use vport event handler for vport cleanup')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx5 flow-steering API (mlx5_create_flow_table/group/rule) never
returns null pointer on error. Even if it was doing that, checking
for IS_ERR_OR_NULL(p) and then returning PTR_ERR(p) would have cause
bugs, since PTR_ERR(NULL) --> success, crash.
To make things more robust and protect against related future bugs,
convert all IS_ERR_OR_NULL checks on returned values to IS_ERR.
Fixes: 5742df0f7d ('net/mlx5: E-Switch, Introduce VST vport ingress/egress ACLs')
Fixes: 86d722ad2c ('net/mlx5: Use flow steering infrastructure for mlx5_en')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must use kvfree() for something that could have been allocated with vzalloc(),
do that.
Fixes: 5742df0f7d ('net/mlx5: E-Switch, Introduce VST vport ingress/egress ACLs')
Fixes: 86d722ad2c ('net/mlx5: Use flow steering infrastructure for mlx5_en')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing capabilities check for E-Switch FDB and ACLs flow
tables before creating their namespace in flow steering.
Fixes: efdc810ba3 ('net/mlx5: Flow steering, Add vport ACL support')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow steering infrastructure is currently used only on link layer
ethernet, therefore the driver should initialize the flow steering
when the device link layer is ethernet.
In addition, add missing capability check before initializing the
namespace of NIC RX flow tables.
Fixes: 2530236303 ('net/mlx5_core: Flow steering tree initialization')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we destroy the last flow table we need to update
the root_ft to NULL.
It fixes an issue for when the last flow table is destroyed
and recreated again, root_ft pointer will not be updated,
as a result traffic will be dropped.
Fixes: 2cc43b494a ('net/mlx5_core: Managing root flow table')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mask the reserved bits when reading the number of newly
created XRCD.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When rtnl_fill_ifinfo() is called for a certain netdevice it queries its
various parameters such as switch id and physical port name. The
function might get called in an atomic context, which means the
underlying driver must not sleep during the query operation.
Don't query the device and sleep during ndo_get_phys_port_name(), but
instead store the needed parameters in port creation time.
Fixes: 2bf9a58675 ("mlxsw: spectrum: Add support for physical port names")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is created following a split / unsplit we need to map it to
the correct module and lane, enable it and then continue to initialize
its various parameters such as MTU and VLAN filters.
Under certain conditions, such as trying to split ports at the bottom
row of the front panel by four, we get firmware errors.
After evaluating this with the firmware team it was decided to alter the
split / unsplit flow, so that first all the affected ports are mapped,
then enabled and finally each is initialized separately.
Fix the split / unsplit flow by first mapping and enabling all the
affected ports. Newer firmware versions will support both flows.
Fixes: 18f1e70c41 ("mlxsw: spectrum: Introduce port splitting")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXVJo5AAoJEHm+PkMAQRiGjioH/3H8Q26FP83Bprhrh3y5EYmz
QSWbq5f5XHGVp4sqc45qdozklh11PrMPkNJQPT2HCTgmtzgeTX5EW9TFaQM/Ubrm
NeYnBW0tTcLP2PhfOyOIJOjE3R1oEYIRQ7zzdOZleViYaqAW2g0frYK0l8AY/KAv
z9mJ8s7xieqSzNTyKNfDPIciT/mO2KMbEHu92EiAkjeCfhuVxUO6PR4wLeZb/85H
I/cOFupU1166xeOZUR0lltvPMz8JznOUB0pg2Ma67TqsNGsPPfsmxEPFlALTTJk/
0V/hVyL4BgvO22LXwMoIxnUcwq/F3ZtlDJRhubeX7m5aS9x2Pb5mQ/g1ko0CXJA=
=5hXk
-----END PGP SIGNATURE-----
Backmerge tag 'v4.7-rc2' into drm-next
Daniel has a pull request that relies on stuff in fixes that are in rc2.
7000-series SFC NICs connected with an SFP+ module currently fail to
report any supported link speeds.
Reported-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the interfaces for ieee/cee dcbnl callbacks and registers
them with the kernel.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the implementation for both cee/ieee dcbnl callbacks by
using the qed query/config APIs.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Query API reads the dcbx data from the device shared memory and return it
to the caller. The config API configures the user provided dcbx values on
the device, and initiates the dcbx negotiation with the peer.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current code "ent_per_page" could be more than "conn_num" making
"conn_num" negative after the subtraction. In the next iteration
through the loop then the negative is treated as a very high positive
meaning we don't put a limit on "ent_num". It could lead to memory
corruption.
Fixes: dbb799c397 ('qed: Initialize hardware for new protocols')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we do not distribute queue resources to enable RSS for VFs
in multi-channel/partition configurations.
Fix this by having each PF(SRIOV capable) calculate it's share of the
15 RSS Policy Tables available per port before provisioning resources for
all the VFs.
This proportional share calculation is done based on division of the
PF's MAX VFs with the Total MAX VFs on that port. It also needs to
learn about the no: of NIC PFs on the port and subtract that from
the 15 RSS Policy Tables on the port.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Skyhawk does support wake-up from ACPI shutdown state - S5, provided the
platform supports it (like Auxiliary power source etc). The changes listed
below are done to fix this.
1) There's no need to defer the HW configuration of WOL to be_suspend().
Remove this in be_suspend() and move it to be_set_wol() ethtool function
so it is configured directly in the context of ethtool. This automatically
takes care of the shutdown case.
2) The driver incorrectly uses WOL_CAP field in the FW response to
get_acpi_wol_cap() command, to determine if WOL is enabled. Instead the
driver must rely on the macaddr field in the response to infer WOL state.
3) In be_get_config() during init, if we find that WOL is enabled in FW,
call pci_enable_wake() to enable pmcsr.pme_en bit. This is needed to
support persistent WOL configuration provided by the FW in some platforms.
4) Remove code in be_set_wol() that writes to PCICFG_PM_CONTROL_OFFSET
to set pme_en bit; pci_enable_wake() sets that.
Fixes: 028991e49 ("Enabling Wake-on-LAN is not supported in S5 state")
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the PF driver provisions resources for VFs, it currently only looks
at max RSS queues available to calculate the number of VF queue pairs.
This logic breaks when there are less number of TX-queues than RSS-queues.
This patch fixes this problem by using the max-TXQs available in the
PF-pool in the calculations. As a part of this change the
be_calculate_vf_qs() routine is renamed as be_calculate_vf_res() and the
code that calculates limits on other related resources is moved here to
contain all resource calculation code inside one routine.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
trivial fix to spelling mistakes and add missing newline in pr_err
messages
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since both CTAG and STAG rx acceleration must be enabled together, we
only need to check one feature flag (NETIF_F_HW_VLAN_CTAG_RX) before
calling __vlan_hwaccel_put_tag().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware can only be set to strip or not strip both the VLAN CTAG and
STAG. It cannot strip one and not strip the other. Add logic to
bnxt_fix_features() to toggle both feature flags when the user is toggling
one of them.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the is_push flag in the software BD before the tx data is pushed to
the chip. It is possible to get the tx interrupt as soon as the tx data
is pushed. The tx handler will not handle the event properly if the
is_push flag is not set and it will crash.
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a future VF would send the PF an unknown message, the PF today would
not send a reply. This would have 2 bad effects:
a. VF would have to timeout on the request.
b. If VF were to send an additional message to PF, firmware would mark
it as malicious.
Instead, if there's some valid reply-address on the message - let the PF
answer and tell the VF it doesn't know the message.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only limitation relating to MACs the PF enforce today on its VFs
is in case it has a forced-unicast MAC address for them, in which case
they can't configure other unicast addresses.
Specifically, the PF isn't enforcing the number of MAC addresse a VF can
configure regardless of the nubmer of such filters agreed upon by PF and
VF during the acquisition process.
PF's shadow-config is now extended to also contain information about its
VFs' unicast addresses configuration, allowing such enforcement.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today, the VF is aware of its queues context-ids, and calculates the
doorbell address when opening its queues on its own.
The configuration of doorbells in HW can sometime in the future be changed
by the PF [hw has several configurable features that might affect doorbell
addresses, e.g., dpm support], this would break compatibility with older
VFs as their calculated doorbell addresses would be incorrect for such a
configuration.
In order to avoid such a backward compatibility failure, let the PF make
the calculation of the doorbell offset based on the context-id, and pass
that to the VF.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several requests the VF can make toward the PF which the driver
would pass to firmware without checking the validity first - specifically,
opening queues and updating vports. Such configurations might cause the
firmware to assert.
This adds validation of the legality of said configurations on the PF side
before passing it onward via ramrod to firmware.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the goals of the vf's first message to the PF [acquire]
is to learn about the number of resources available to it [macs, vlans,
etc.]. This is done via negotiation - the VF requires a set of resources,
which the PF either approves or disaproves and sends a smaller set of
resources as alternative. In this later case, the VF is then expected to
either abort the probe or re-send the acquire message with less
required resources.
While this infrastructure exists since the initial submision of qed
SRIOV support, it's in fact completely inoperational - PF isn't really
looking into the resources the VF has asked for and is never going to
reply to the VF that it lacks resources.
This patch addresses this flow, fixing it and allowing the PF and VF
to actually agree on a set of resources.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver require an exact match between VF and PF storm firmware;
Any difference would fail the VF acquire message, causing the VF probe
to be aborted.
While there's still dependencies between the two, the recent FW submission
has relaxed the match requirement - instead of an exact match, there's now
a 'fastpath' HSI major/minor scheme, where VFs and PFs that match in their
major number can co-exist even if their minor is different.
In order to accomadate this change some changes in the vf-start init flow
had to be made, as the VF start ramrod now has to be sent only after PF
learns which fastpath HSI its VF is requiring.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_workqueue replaces deprecated create_workqueue().
A dedicated workqueue has been used since the workitem viz
(&db_wq->wk.work which maps to check_db_timeout) is involved
in normal device operation. WQ_MEM_RECLAIM has been set to guarantee
forward progress under memory pressure, which is a requirement here.
Since there are only a fixed number of work items, explicit concurrency
limit is unnecessary.
flush_workqueue is unnecessary since destroy_workqueue() itself calls
drain_workqueue() which flushes repeatedly till the workqueue
becomes empty.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_workqueue replaces deprecated create_workqueue().
A dedicated workqueue has been used since the workitem viz
(&cwq->wk.work which maps to oct_poll_req_completion) is involved
in normal device operation. WQ_MEM_RECLAIM has been set to guarantee
forward progress under memory pressure, which is a requirement here.
Since there are only a fixed number of work items, explicit concurrency
limit is unnecessary.
flush_workqueue is unnecessary since destroy_workqueue() itself calls
drain_workqueue() which flushes repeatedly till the workqueue
becomes empty. Hence the call to flush_workqueue() has been dropped.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since implementing VLAN filtering in commit 05cc5a39dd
("bnx2x: add vlan filtering offload") bnx2x refuses to add a VLAN while
the interface is down:
# ip link add link enp3s0f0 enp3s0f0_10 type vlan id 10
RTNETLINK answers: Bad address
and in dmesg (with bnx2x.debug=0x20):
bnx2x: [bnx2x_vlan_rx_add_vid:12941(enp3s0f0)]Ignoring VLAN
configuration the interface is down
Other drivers have no problem with this.
Fix this peculiar behavior in the following way:
- Accept requests to add/kill VID regardless of the device state.
Maintain the requested list of VIDs in the bp->vlan_reg list.
- If the device is up, try to configure the VID list into the hardware.
If we run out of VLAN credits or encounter a failure configuring an
entry, fall back to accepting all VLANs.
If we successfully configure all entries from the list, turn the
fallback off.
- Use the same code for reconfiguring VLANs during NIC load.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enet needs to get configration parameter by acpi. This patch
adds support of ACPI for enet. The configuration parameter will
be configed in BIOS.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The miscellaneous operation is implemented in BIOS, the kernel can call
_DSM method help to call the implementation in ACPI case. Here is a patch
to do that.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ACPI case, there is no interface to register phy device to mdio-bus.
Phy device has to be registered itself to mdio-bus, and then enet can
get the phy device's info so that it can config the phy-device to help
to trasmit and receive data.
HNS hardware topology is as below. The MDIO controller may control several
PHY-devices, and each PHY-device connects to a MAC device. PHY-devices
will register when each mac find PHY device in initial sequence.
cpu
|
|
-------------------------------------------
| | |
| | |
| dsaf |
MDIO | MDIO
| --------------------------- |
| | | | | |
| | | | | |
| MAC MAC MAC MAC |
| | | | | |
---- |-------- |-------- | | --------
|| || || ||
PHY PHY PHY PHY
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dsaf needs to get configuration parameter by ACPI, so this patch add
support of ACPI.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The misc operation for different hw platform may be different, if using
current implementation, it will add a new branch on each function for
every new hw platform, so we add a method for this operation.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As device_node is only used by DT case, HNS needs to treat the other
cases including ACPI. It needs to use uniform ways to handle both of
DT and ACPI. This patch chooses phy_device, and of_phy_connect and
of_phy_attach are only used by DT case. It needs to use uniform interface
to handle that sequence by both DT and ACPI.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As device_node is only used by DT case, it is expected to find uniform
ways. So fwnode_handle is the suitable method.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As irq_of_parse_and_map is only used by DT case, it is excepted to use
a uniform interface. So it is used platform_get_irq() instead.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OF series functions can be used only for DT case. Use unified
device property function instead to support both DT and ACPI.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns-mdio needs to register itself to mii-bus. The info of the device can
be read by both DT and ACPI.
HNS tries to call Linux PHY driver to help access PHY-devices, the HNS
hardware topology is as below. The MDIO controller may control several
PHY-devices, and each PHY-device connects to a MAC device. The MDIO will
be registered to mdiobus, then PHY-devices will register when each mac
find PHY device.
cpu
|
|
-------------------------------------------
| | |
| | |
| dsaf |
MDIO | MDIO
| --------------------------- |
| | | | | |
| | | | | |
| MAC MAC MAC MAC |
| | | | | |
---- |-------- |-------- | | --------
|| || || ||
PHY PHY PHY PHY
And the driver can handle reset sequence by _RST method in DSDT in ACPI
case.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hns-mdio only supports DT case now. do some cleanup to prepare
for introducing other cases later, no functional change.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RoCE and iSCSI would require some added/changed hw configuration in order
to properly run; The biggest single change being the requirement of
allocating and mapping host memory for several HW blocks that aren't being
used by qede [SRC, QM, TM, etc.].
In addition, whereas qede is only using context memory for HW blocks, the
new protocol would also require task memories to be added.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds in the ecore 2 new personalities in addition to
QED_PCI_ETH - QED_PCI_ISCSI and QED_PCI_ETH_ROCE.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the qed portion of the RoCE & iSCSI firmware HSI,
as well as adding several new common HSI files which would be required
by both qed and qed* protocols.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RoCE driver is going to need a 32-bit chain [current chain implementation
for qed* currently supports only 16-bit producer/consumer chains].
This patch adds said support, as well as doing other slight tweaks and
modifications to qed's chain API.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an external Gigabit PHY is connected to either of the MACs we need to
be able to tell the PHY to use a delay. Not doing so will result in heavy
packet loss and/or data corruption when using PHYs such as the IC+ IP1001.
We tell the PHY which MII delay mode to use via the devictree.
The ethernet driver needs to be adapted to handle all 3 rgmii-*id modes
in the same way as normal rgmii when setting up the MAC.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MT7623 SoC has a builtin gigabit switch. If we want to use it, GMAC1
needs to be configured using a fixed link speed and flow control settings.
The easiest way to do this is to used the fixed-phy driver, allowing us to
reuse the existing mdio polling code to setup the MAC.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code will not setup the PHYs advertisement features correctly.
Fix this and properly advertise Gigabit features and properly handle
asymmetric pause frames.
Signed-off-by: Sean Wang <keyhaede@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently uses kfree() to clear the mii_bus. This is not the
correct way to clear the memory and mdiobus_free() should be used instead.
This patch fixes the two instances where this happens in the driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason in this lock. At least for now.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx-usecs shouldn't be changed while interface down/up.
Currently, for instance, if it's set to 100us, after interface
down/up it's 500us. It's a hidden bug that can lead to lavish
interrupt pacing time increasing while "down/up" up to max value.
Steps to reproduce:
- set rx-usecs to be 100us
- down/up interface
- read new unexpected rx-usecs
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the transmit hardware timestamping is enabled, an additional
TxBD would be added and would be set as the last TxBD with TXBD_LAST
and TXBD_INTERRUPT. However this has been broken by a patch recently.
This made the software couldn't get transmit hardware timestamps and
resulted in call trace. So, this patch is to fix this issue.
Fixes: 48963b4492 ("gianfar: Remove redundant ops for do_tstamp
from xmit()")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The New QED firmware contains several fixes, including:
- Wrong classification of packets in 4-port devices.
- Anti-spoof interoperability with encapsulated packets.
- Tx-switching of encapsulated packets.
It also slightly improves Tx performance of the device.
In addition, this firmware contains the necessary logic for
supporting iscsi & rdma, for which we plan on pushing protocol
drivers in the imminent future.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_workqueue replaces deprecated create_workqueue().
A dedicated workqueue has been used since the workitems are involved
in normal device operation. Workitems &priv->rx_work and &priv->tx_work,
map to w5100_rx_work and w5100_tx_work respectively and are involved in
receiving and transmitting packets. Forward progress under
memory pressure is a requirement here.
create_workqueue has been replaced with alloc_workqueue with max_active
as 0 since there is no need for throttling the number of active work
items.
Since the driver may be used in memory reclaim path,
WQ_MEM_RECLAIM has been set to guarantee forward progress.
flush_workqueue is unnecessary since destroy_workqueue() itself calls
drain_workqueue() which flushes repeatedly till the workqueue
becomes empty. Hence the call to flush_workqueue() has been dropped.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac_mdio_reset() has been updated to use msleep rather udelay
(as some PHY requires a one second delay there).
It called from stmmac_resume() within the spin_lock_irqsave block
atomic context triggering 'scheduling while atomic'.
The stmmac_priv lock usage is not fully documented, but it seems
to protect the access to the MAC registers / DMA structures rather
than the MDIO bus or the PHY (which have separate locking),
so we can push the spin_lock after the stmmac_mdio_reset call.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Writing a non-zero value to the manual PAUSE frame register (MPR) starts
the transmission of a PAUSE frame.
A PAUSE frame is sent in ravb_emac_init(), but it is not expected behavior.
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc warns about qed_fill_link possibly accessing uninitialized data:
drivers/net/ethernet/qlogic/qed/qed_main.c: In function 'qed_fill_link':
drivers/net/ethernet/qlogic/qed/qed_main.c:1170:35: error: 'link_caps' may be used uninitialized in this function [-Werror=maybe-uninitialized]
While this warning is only about the specific case of CONFIG_QED_SRIOV
being disabled but the function getting called for a VF (which should
never happen), another possibility is that qed_mcp_get_*() fails without
returning data.
This rearranges the code so we bail out in either of the two cases
and print a warning instead of accessing the uninitialized data.
The qed_link_output structure remains untouched in this case, but
all callers first call memset() on it, so at least we are not leaking
stack data then.
As discussed, we also use a compile-time check to ensure we never
use any of the VF code if CONFIG_QED_SRIOV is disabled, and the
PCI device table is updated to no longer bind to virtual functions
in that configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
priv is assigned to NULL however some of the early error exit paths to
label 'free' dereference priv, causing a null pointer dereference.
Move the label 'free' to just the free_netdev statement, and add a new
exit path 'free2' for the error cases were clk_disable_unprepare needs
calling before the final free.
Fixes issue found by CoverityScan, CID#113260
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's not much point, except compile test, enabling the stmmac
platform drivers unless their actual SoC is enabled. They're not
useful without it.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use SET_RUNTIME_PM_OPS macro instead of assigning a member of
dev_pm_ops directly.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The H/W manual recommends B'10 or B'11 in a value of the separation
filtering select bits in the receive configuration register (RCR.ESF).
When B'10 is set, frames from non-matching streams are discarded.
When B'11 is set, frames from non-matching streams are processed in
reception queue 0 (best effort).
This patch sets B'11 in ESF.
[ykaneko0929@gmail.com: revised this commit message]
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drm-intel-next-2016-05-22:
- cmd-parser support for direct reg->reg loads (Ken Graunke)
- better handle DP++ smart dongles (Ville)
- bxt guc fw loading support (Nick Hoathe)
- remove a bunch of struct typedefs from dpll code (Ander)
- tons of small work all over to avoid casting between drm_device and the i915
dev struct (Tvrtko&Chris)
- untangle request retiring from other operations, also fixes reset stat corner
cases (Chris)
- skl atomic watermark support from Matt Roper, yay!
- various wm handling bugfixes from Ville
- big pile of cdclck rework for bxt/skl (Ville)
- CABC (Content Adaptive Brigthness Control) for dsi panels (Jani&Deepak M)
- nonblocking atomic commits for plane-only updates (Maarten Lankhorst)
- bunch of PSR fixes&improvements
- untangle our map/pin/sg_iter code a bit (Dave Gordon)
drm-intel-next-2016-05-08:
- refactor stolen quirks to share code between early quirks and i915 (Joonas)
- refactor gem BO/vma funcstion (Tvrtko&Dave)
- backlight over DPCD support (Yetunde Abedisi)
- more dsi panel sequence support (Jani)
- lots of refactoring around handling iomaps, vma, ring access and related
topics culmulating in removing the duplicated request tracking in the execlist
code (Chris & Tvrtko) includes a small patch for core iomapping code
- hw state readout for bxt dsi (Ramalingam C)
- cdclk cleanups (Ville)
- dedupe chv pll code a bit (Ander)
- enable semaphores on gen8+ for legacy submission, to be able to have a direct
comparison against execlist on the same platform (Chris) Not meant to be used
for anything else but performance tuning
- lvds border bit hw state checker fix (Jani)
- rpm vs. shrinker/oom-notifier fixes (Praveen Paneri)
- l3 tuning (Imre)
- revert mst dp audio, it's totally non-functional and crash-y (Lyude)
- first official dmc for kbl (Rodrigo)
- and tons of small things all over as usual
* 'drm-intel-next' of git://anongit.freedesktop.org/drm-intel: (194 commits)
drm/i915: Revert async unpin and nonblocking atomic commit
drm/i915: Update DRIVER_DATE to 20160522
drm/i915: Inline sg_next() for the optimised SGL iterator
drm/i915: Introduce & use new lightweight SGL iterators
drm/i915: optimise i915_gem_object_map() for small objects
drm/i915: refactor i915_gem_object_pin_map()
drm/i915/psr: Implement PSR2 w/a for gen9
drm/i915/psr: Use ->get_aux_send_ctl functions
drm/i915/psr: Order DP aux transactions correctly
drm/i915/psr: Make idle_frames sensible again
drm/i915/psr: Try to program link training times correctly
drm/i915/userptr: Convert to drm_i915_private
drm/i915: Allow nonblocking update of pageflips.
drm/i915: Check for unpin correctness.
Reapply "drm/i915: Avoid stalling on pending flips for legacy cursor updates"
drm/i915: Make unpin async.
drm/i915: Prepare connectors for nonblocking checks.
drm/i915: Pass atomic states to fbc update functions.
drm/i915: Remove reset_counter from intel_crtc.
drm/i915: Remove queue_flip pointer.
...
Pull networking fixes from David Miller:
1) Fix negative error code usage in ATM layer, from Stefan Hajnoczi.
2) If CONFIG_SYSCTL is disabled, the default TTL is not initialized
properly. From Ezequiel Garcia.
3) Missing spinlock init in mvneta driver, from Gregory CLEMENT.
4) Missing unlocks in hwmb error paths, also from Gregory CLEMENT.
5) Fix deadlock on team->lock when propagating features, from Ivan
Vecera.
6) Work around buffer offset hw bug in alx chips, from Feng Tang.
7) Fix double listing of SCTP entries in sctp_diag dumps, from Xin
Long.
8) Various statistics bug fixes in mlx4 from Eric Dumazet.
9) Fix some randconfig build errors wrt fou ipv6 from Arnd Bergmann.
10) All of l2tp was namespace aware, but the ipv6 support code was not
doing so. From Shmulik Ladkani.
11) Handle on-stack hrtimers properly in pktgen, from Guenter Roeck.
12) Propagate MAC changes properly through VLAN devices, from Mike
Manning.
13) Fix memory leak in bnx2x_init_one(), from Vitaly Kuznetsov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (62 commits)
sfc: Track RPS flow IDs per channel instead of per function
usbnet: smsc95xx: fix link detection for disabled autonegotiation
virtio_net: fix virtnet_open and virtnet_probe competing for try_fill_recv
bnx2x: avoid leaking memory on bnx2x_init_one() failures
fou: fix IPv6 Kconfig options
openvswitch: update checksum in {push,pop}_mpls
sctp: sctp_diag should dump sctp socket type
net: fec: update dirty_tx even if no skb
vlan: Propagate MAC address to VLANs
atm: iphase: off by one in rx_pkt()
atm: firestream: add more reserved strings
vxlan: Accept user specified MTU value when create new vxlan link
net: pktgen: Call destroy_hrtimer_on_stack()
timer: Export destroy_hrtimer_on_stack()
net: l2tp: Make l2tp_ip6 namespace aware
Documentation: ip-sysctl.txt: clarify secure_redirects
sfc: use flow dissector helpers for aRFS
ieee802154: fix logic error in ieee802154_llsec_parse_dev_addr
net: nps_enet: Disable interrupts before napi reschedule
net/lapb: tuse %*ph to dump buffers
...
Otherwise we get confused when two flows on different channels get the
same flow ID.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x_init_bp() allocates memory with bnx2x_alloc_mem_bp() so if we
fail later in bnx2x_init_one() we need to free this memory
with bnx2x_free_mem_bp() to avoid leakages. E.g. I'm observing memory
leaks reported by kmemleak when a failure (unrelated) happens in
bnx2x_vfpf_acquire().
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If dirty_tx isn't updated, then dma_unmap_single
can be called twice.
This fixes a
[ 58.420980] ------------[ cut here ]------------
[ 58.425667] WARNING: CPU: 0 PID: 377 at /home/schurig/d/mkarm/linux-4.5/lib/dma-debug.c:1096 check_unmap+0x9d0/0xab8()
[ 58.436405] fec 2188000.ethernet: DMA-API: device driver tries to free DMA memory it has not allocated [device address=0x0000000000000000] [size=66 bytes]
encountered by Holger
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Tested-by: <holgerschurig@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since NAPI works by shutting down event interrupts when theres
work and turning them on when theres none, the net driver must
make sure that interrupts are disabled when it reschedules polling.
By calling napi_reschedule, the driver switches to polling mode,
therefor there should be no interrupt interference.
Any received packets will be handled in nps_enet_poll by polling the HW
indication of received packet until all packets are handled.
Signed-off-by: Elad Kanfi <eladkan@mellanox.com>
Acked-by: Noam Camus <noamca@mellanox.com>
Tested-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently 100g devices don't support minimum/maximum BW configurations,
yet link flaps might cause the driver to attempt to do such a
configuration. Prevent this just as we do for the maximum BW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapter can support 100g in both MSIx and INTa, but not in MSI.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the HW configurations are currently missing for 100g devices.
This can cause various classification issues, as well as prevent device
from fully reaching line-rate.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When DCBx re-negotiation is occurring, the PF's configurations for
maximum and minimum bandwidth guarantees are currently lost.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 39651abd28 ("qed: add support for dcbx") is re-configuring
the QM hw-block as part of its sequence. This is done in attention
handling context which is non-sleepable, yet memory is allocated in
this flow using GFP_KERNEL.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PFs and VFs differ in their registered ethtool operations,
but they're using a common function for get_sset_count().
As a result, `ethtool -i' for a VF would indicate it supports
selftest, although that's not the case.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since driver is using a FW-based GRO implementation, this has some
effects on its ability to cope with GRO enablement/disablement.
As a result, driver must perform an inner-reload as a result of a state
change in the offload configuration of said feature.
[Failure to do so means network stack would continue to receive
aggregated packets even though user requested the feature to be disabled].
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF is currently ignoring the minimum provided by the API,
mistakenly using the maximum for minimum as well.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We simply can use the standard net_device stats.
We do not need to clear fields that are already 0.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4 uses a private struct net_device_stats in a vain attempt
to avoid races.
This is buggy because multiple cpus could call mlx4_en_get_stats()
at the same time, so ret_stats can not guarantee stable results.
To fix this, we need to switch to ndo_get_stats64() as this
method provides per-thread storage.
This allows to reduce mlx4_en_priv bloat.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en_clear_stats() clears about everything but few TX ring
fields are missing :
- queue_stopped, wake_queue, tso_packets, xmit_more
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) mlx4_en_xmit() can increment priv->stats.tx_dropped, but this variable
is overwritten in mlx4_en_DUMP_ETH_STATS().
2) This increment was not SMP safe, as a port might have many TX queues.
Add a per TX ring tx_dropped to fix these issues.
This is u32 as mlx4_en_DUMP_ETH_STATS() will add a 32bit field.
So lets avoid bugs with SNMP agents having to cope with partial
overwraps. (One of these agents being bond_fold_stats())
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Willem de Bruijn <willemb@google.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a typo in the driver, replace comma with a semicolon at the end
of statement. While using comma is a legal C here and probably does
not even generate compiler warning, it was unlikely the intention.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Caesar Wang <wxt@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memcpy() currently copies mdio_bus_data into new_bus->irq, which
makes no sense, since the mdio_bus_data structure contains more than
just irqs. The code was likely supposed to copy mdio_bus_data->irqs
into the new_bus->irq instead, so fix this.
Fixes: e7f4dc3536 ("mdio: Move allocation of interrupts into core")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch follows Eric Dumazet's commit 7b70176421 for Atheros
atl1c driver to fix one exactly same bug in alx driver, that the
network link will be lost in 1-5 minutes after the device is up.
My laptop Lenovo Y580 with Atheros AR8161 ethernet device hit the
same problem with kernel 4.4, and it will be cured by Jarod Wilson's
commit c406700c for alx driver which get merged in 4.5. But there
are still some alx devices can't function well even with Jarod's
patch, while this patch could make them work fine. More details on
https://bugzilla.kernel.org/show_bug.cgi?id=70761
The debug shows the issue is very likely to be related with the RX
DMA address, specifically 0x...f80, if RX buffer get 0x...f80 several
times, their will be RX overflow error and device will stop working.
For kernel 4.5.0 with Jarod's patch which works fine with my
AR8161/Lennov Y580, if I made some change to the
__netdev_alloc_skb
--> __alloc_page_frag()
to make the allocated buffer can get an address with 0x...f80,
then the same error happens. If I make it to 0x...f40 or 0x....fc0,
everything will be still fine. So I tend to believe that the
0x..f80 address cause the silicon to behave abnormally.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=70761
Cc: Eric Dumazet <edumazet@google.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Tested-by: Ole Lukoie <olelukoie@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise, if we fail to allocate new PIO buffers, our TXQs will try to
use the old ones, which aren't there any more.
Fixes: 183233bec8 "sfc: Allocate and link PIO buffers; map them with write-combining"
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The spinlock used by the hwbm functions must be initialized by the
network driver. This commit fixes this lack and the following erros when
lockdep is enabled:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
[<c010ff80>] (unwind_backtrace) from [<c010bd08>] (show_stack+0x10/0x14)
[<c010bd08>] (show_stack) from [<c032913c>] (dump_stack+0xb4/0xe0)
[<c032913c>] (dump_stack) from [<c01670e4>] (__lock_acquire+0x1f58/0x2060)
[<c01670e4>] (__lock_acquire) from [<c0167dec>] (lock_acquire+0xa4/0xd0)
[<c0167dec>] (lock_acquire) from [<c06f6650>] (_raw_spin_lock_irqsave+0x54/0x68)
[<c06f6650>] (_raw_spin_lock_irqsave) from [<c058e830>] (hwbm_pool_add+0x1c/0xdc)
[<c058e830>] (hwbm_pool_add) from [<c043f4e8>] (mvneta_bm_pool_use+0x338/0x490)
[<c043f4e8>] (mvneta_bm_pool_use) from [<c0443198>] (mvneta_probe+0x654/0x1284)
[<c0443198>] (mvneta_probe) from [<c03b894c>] (platform_drv_probe+0x4c/0xb0)
[<c03b894c>] (platform_drv_probe) from [<c03b7158>] (driver_probe_device+0x214/0x2c0)
[<c03b7158>] (driver_probe_device) from [<c03b72c4>] (__driver_attach+0xc0/0xc4)
[<c03b72c4>] (__driver_attach) from [<c03b5440>] (bus_for_each_dev+0x68/0x9c)
[<c03b5440>] (bus_for_each_dev) from [<c03b65b8>] (bus_add_driver+0x1a0/0x218)
[<c03b65b8>] (bus_add_driver) from [<c03b79cc>] (driver_register+0x78/0xf8)
[<c03b79cc>] (driver_register) from [<c01018f4>] (do_one_initcall+0x90/0x1dc)
[<c01018f4>] (do_one_initcall) from [<c0900de4>] (kernel_init_freeable+0x15c/0x1fc)
[<c0900de4>] (kernel_init_freeable) from [<c06eed90>] (kernel_init+0x8/0x114)
[<c06eed90>] (kernel_init) from [<c0107910>] (ret_from_fork+0x14/0x24)
Fixes: baa11ebc0c ("net: mvneta: Use the new hwbm framework")
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the coding error in determining the enable flag for
the application/protocol. The enable flag should be set for all protocols
but the eth.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One timer, whose handler keeps reading on MMIO register for EEH
core to detect error in time, is started when the PCI device driver
is loaded. MMIO register can't be accessed during PE reset in EEH
recovery. Otherwise, the unexpected recursive error is triggered.
The timer isn't closed that time if the interface isn't brought
up. So the unexpected recursive error is seen during EEH recovery
when the interface is down.
This avoids the unexpected recursive EEH error by closing the timer
in qlge_io_error_detected() before EEH PE reset unconditionally. The
timer is started unconditionally after EEH PE reset in qlge_io_resume().
Also, the timer should be closed unconditionally when the device is
removed from the system permanently in qlge_io_error_detected().
Reported-by: Shriya R. Kulkarni <shriyakul@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"priority" needs to be signed for the error handling to work.
Fixes: 39651abd28 ('qed: add support for dcbx.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the statement
assert(priv || priv->ae_handle);
the right side of || is only evaluated if priv is null.
v2:
As suggested by David Leight and David Miller the assert
statements are removed.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull sparc updates from David Miller:
"Some 32-bit kgdb cleanups from Sam Ravnborg, and a hugepage TLB flush
overhead fix on 64-bit from Nitin Gupta"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Reduce TLB flushes during hugepte changes
aeroflex/greth: fix warning about unused variable
openprom: fix warning
sparc32: drop superfluous cast in calls to __nocache_pa()
sparc32: fix build with STRICT_MM_TYPECHECKS
sparc32: use proper prototype for trapbase
sparc32: drop local prototype in kgdb_32
sparc32: drop hardcoding trap_level in kgdb_trap
Pull networking fixes and more updates from David Miller:
1) Tunneling fixes from Tom Herbert and Alexander Duyck.
2) AF_UNIX updates some struct sock bit fields with the socket lock,
whereas setsockopt() sets overlapping ones with locking. Seperate
out the synchronized vs. the AF_UNIX unsynchronized ones to avoid
corruption. From Andrey Ryabinin.
3) Mount BPF filesystem with mount_nodev rather than mount_ns, from
Eric Biederman.
4) A couple kmemdup conversions, from Muhammad Falak R Wani.
5) BPF verifier fixes from Alexei Starovoitov.
6) Don't let tunneled UDP packets get stuck in socket queues, if
something goes wrong during the encapsulation just drop the packet
rather than signalling an error up the call stack. From Hannes
Frederic Sowa.
7) SKB ref after free in batman-adv, from Florian Westphal.
8) TCP iSCSI, ocfs2, rds, and tipc have to disable BH in it's TCP
callbacks since the TCP stack runs pre-emptibly now. From Eric
Dumazet.
9) Fix crash in fixed_phy_add, from Rabin Vincent.
10) Fix length checks in xen-netback, from Paul Durrant.
11) Fix mixup in KEY vs KEYID macsec attributes, from Sabrina Dubroca.
12) RDS connection spamming bug fixes from Sowmini Varadhan
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (152 commits)
net: suppress warnings on dev_alloc_skb
uapi glibc compat: fix compilation when !__USE_MISC in glibc
udp: prevent skbs lingering in tunnel socket queues
bpf: teach verifier to recognize imm += ptr pattern
bpf: support decreasing order in direct packet access
net: usb: ch9200: use kmemdup
ps3_gelic: use kmemdup
net:liquidio: use kmemdup
bpf: Use mount_nodev not mount_ns to mount the bpf filesystem
net: cdc_ncm: update datagram size after changing mtu
tuntap: correctly wake up process during uninit
intel: Add support for IPv6 IP-in-IP offload
ip6_gre: Do not allow segmentation offloads GRE_CSUM is enabled with FOU/GUE
RDS: TCP: Avoid rds connection churn from rogue SYNs
RDS: TCP: rds_tcp_accept_worker() must exit gracefully when terminating rds-tcp
net: sock: move ->sk_shutdown out of bitfields.
ipv6: Don't reset inner headers in ip6_tnl_xmit
ip4ip6: Support for GSO/GRO
ip6ip6: Support for GSO/GRO
ipv6: Set features for IPv6 tunnels
...
Fix following warning:
aeroflex/greth.c:1326:11: warning: unused variable 'phy' [-Wunused-variable]
The variable was unused - remove it.
It looks like this warning has been there forever - was found by an
allyesconfig build of sparc32.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Kristoffer Glembo <kristoffer@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kmemdup when some other buffer is immediately copied into allocated
region. It replaces call to allocation followed by memcpy, by a single
call to kmemdup.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kmemdup when some other buffer is immediately copied into allocated
region. It replaces call to allocation followed by memcpy, by a single
call to kmemdup.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for offloading IPXIP6 type packets that represent
either IPv4 or IPv6 encapsulated inside of an IPv6 outer IP header. In
addition with this change we should also be able to support FOU
encapsulated traffic with outer IPv6 headers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch defines two new GSO definitions SKB_GSO_IPXIP4 and
SKB_GSO_IPXIP6 along with corresponding NETIF_F_GSO_IPXIP4 and
NETIF_F_GSO_IPXIP6. These are used to described IP in IP
tunnel and what the outer protocol is. The inner protocol
can be deduced from other GSO types (e.g. SKB_GSO_TCPV4 and
SKB_GSO_TCPV6). The GSO types of SKB_GSO_IPIP and SKB_GSO_SIT
are removed (these are both instances of SKB_GSO_IPXIP4).
SKB_GSO_IPXIP6 will be used when support for GSO with IP
encapsulation over IPv6 is added.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Updates to the new Intel X722 iWARP driver
- Updates to the hfi1 driver
- Fixes for the iw_cxgb4 driver
- Misc core fixes
- Generic RDMA READ/WRITE API addition
- SRP updates
- Misc ipoib updates
- Minor mlx5 updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=e+Zv
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"Primary 4.7 merge window changes
- Updates to the new Intel X722 iWARP driver
- Updates to the hfi1 driver
- Fixes for the iw_cxgb4 driver
- Misc core fixes
- Generic RDMA READ/WRITE API addition
- SRP updates
- Misc ipoib updates
- Minor mlx5 updates"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (148 commits)
IB/mlx5: Fire the CQ completion handler from tasklet
net/mlx5_core: Use tasklet for user-space CQ completion events
IB/core: Do not require CAP_NET_ADMIN for packet sniffing
IB/mlx4: Fix unaligned access in send_reply_to_slave
IB/mlx5: Report Scatter FCS device capability when supported
IB/mlx5: Add Scatter FCS support for Raw Packet QP
IB/core: Add Scatter FCS create flag
IB/core: Add Raw Scatter FCS device capability
IB/core: Add extended device capability flags
i40iw: pass hw_stats by reference rather than by value
i40iw: Remove unnecessary synchronize_irq() before free_irq()
i40iw: constify i40iw_vf_cqp_ops structure
IB/mlx5: Add UARs write-combining and non-cached mapping
IB/mlx5: Allow mapping the free running counter on PROT_EXEC
IB/mlx4: Use list_for_each_entry_safe
IB/SA: Use correct free function
IB/core: Fix a potential array overrun in CMA and SA agent
IB/core: Remove unnecessary check in ibnl_rcv_msg
IB/IWPM: Fix a potential skb leak
RDMA/nes: replace custom print_hex_dump()
...
Driver incorrectly uses dma_unmap_addr_set() to set
a variable which is in truth a dma_addr_t
[i.e not defined using DEFINE_DMA_UNMAP_ADDR()] and is
being used by the driver flows other than unmapping
physical addresses. This patch fixes driver fastpath
where CONFIG_NEED_DMA_MAP_STATE is not set.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many developers already know that field for reference count of the
struct page is _count and atomic type. They would try to handle it
directly and this could break the purpose of page reference count
tracepoint. To prevent direct _count modification, this patch rename it
to _refcount and add warning message on the code. After that, developer
who need to handle reference count will find that field should not be
accessed directly.
[akpm@linux-foundation.org: fix comments, per Vlastimil]
[akpm@linux-foundation.org: Documentation/vm/transhuge.txt too]
[sfr@canb.auug.org.au: sync ethernet driver changes]
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Manish Chopra <manish.chopra@qlogic.com>
Cc: Yuval Mintz <yuval.mintz@qlogic.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
page_reference manipulation functions are introduced to track down
reference count change of the page. Use it instead of direct
modification of _count.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(a && a > 0) is equivalent to (a > 0).
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ehea_get_port may return NULL. Do not dereference NULL value.
Fixes: 8c4877a412 ("ehea: Use the standard logging functions")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function bgx_lmac_handler only use a member of
lmac after checking it is not null.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, we've fired all our completion callbacks straight from
our ISR.
Some of those callbacks were lightweight (for example, mlx5 Ethernet
napi callbacks), but some of them did more work (for example,
the user-space RDMA stack uverbs' completion handler). Besides that,
doing more than the minimal work in ISR is generally considered wrong,
it could even lead to a hard lockup of the system. Since when a lot
of completion events are generated by the hardware, the loop over
those events could be so long, that we'll get into a hard lockup by
the system watchdog.
In order to avoid that, add a new way of invoking completion events
callbacks. In the interrupt itself, we add the CQs which receive
completion event to a per-EQ list and schedule a tasklet. In the
tasklet context we loop over all the CQs in the list and invoke the
user callback.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The current logic around the 'use_dac' module parameter prevents the
r81969 driver from being loadable on 64-bit systems without any RAM
below 4 GB when the parameter is left at its default value.
So introduce a new default value -1 which indicates that 64-bit DMA
should be enabled on sufficiently recent PCIe chips, i.e., versions
RTL_GIGA_MAC_VER_18 or later. Explicit param values of 0 or 1 retain
the existing behavior of unconditionally enabling/disabling 64-bit DMA
on 64-bit architectures (i.e., regardless of the type and version of the
chip)
Since PCIe chips do not need to CPlusCmd Dual Address Cycle to be set,
make that conditional on the device type as well.
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem is that fib_info->nh is [0] so the struct fib_info
allocation size depends on number of nexthops. If we just copy fib_info,
we do not copy the nexthops info and driver accesses memory which is not
ours.
Given the fact that fib4 does not defer operations and therefore it does
not need copy, just pass the pointer down to drivers as it was done
before.
Fixes: 850d0cbc91 ("switchdev: remove pointers from switchdev objects")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ethernet devices, net_device.name will be eth%d before
register_netdev() is called. Don't print the net_device name until
the format string is replaced.
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: Marcel Ziswiler <marcel@ziswiler.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Barry Song <Baohua.Song@csr.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the necessary driver support for Management Firmware to
configure the device/firmware with the dcbx results. Management Firmware
is responsible for communicating the DCBX and driving the negotiation,
but the driver has responsibility of receiving async notification and
configuring the results in hw/fw. This patch also adds the dcbx support for
future protocols (e.g., FCoE) as preparation to their imminent submission.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When reopening the network device on ra7795/salvator-x, e.g. after a
DHCP timeout:
IP-Config: Reopening network devices...
genirq: Flags mismatch irq 139. 00000000 (eth0:ch0:rx_be) vs. 00000000 (ravb e6800000.ethernet eth0: cannot request IRQ eth0:ch0:rx_be
IP-Config: Failed to open eth0
IP-Config: No network devices available
The "mismatch" is due to requesting an IRQ that is already in use,
while IRQF_PROBE_SHARED wasn't set.
However, the real cause is that ravb_close() doesn't release any of the
R-Car Gen3-specific secondary IRQs.
Add the missing free_irq() calls to fix this.
Fixes: f51bdc236b ("ravb: Add dma queue interrupt support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This line was indented more than it should be.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2016-05-16
This series contains 2 fixes to ixgbe only.
Emil fixes transmit hangs when enabling SRIOV by swapping the parameters
in GENMASK in order to generate the correct mask.
Alex fixes his previous patch b83e30104b ("ixgbe/ixgbevf: Add support
for GSO partial") where he somehow transposed the location of setting
the VLAN features in netdev->features and the configuration of the
vlan_features.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Backmerge request by Jani to get at
commit 249c4f538b
Author: Deepak M <m.deepak@intel.com>
Date: Wed Mar 30 17:03:39 2016 +0300
drm: Add new DCS commands in the enum list
Some simple conflicts in intel_dp.c.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f748be531d ("stmmac: support new GMAC4") reverted a previous fix
by mistake. This commit re-applies said fix:
commit dec2165ff3
Author: Sonic Zhang <sonic.zhang@analog.com>
Date: Thu Jan 22 14:55:57 2015 +0800
stmmac: hardware TX COE doesn't work when force_thresh_dma_mode is set
Clear the TX COE bit when force_thresh_dma_mode is set even hardware
dma capability says support.
Tested on BF609.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested on LPC4350 Hitex board.
Fixes: f748be531d ("stmmac: support new GMAC4")
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like at some point I somehow transposed the location of setting
the VLAN features in netdev->features and the configuration of the
vlan_features. As a result the driver is now generating a warning about
vlan_features being setup incorrectly.
This patch corrects that by placing the update of netdev->features to
include the VLAN features so that it is after the point where we write
netdev->features into netdev->vlan_features.
Fixes: b83e30104b ("ixgbe/ixgbevf: Add support for GSO partial")
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Swap the parameters in GENMASK in order to generate the correct mask.
This change fixes Tx hangs when enabling SRIOV.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VF's probe might log that it has no PM capability in its PCI configuration
space. As this is a valid configuration, silence such prints.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In multi-function modes, PFs are currently limited to using 16 VFs -
But that limitation would also currently apply in case there's a single
PCI function exposed, where no such restriction should have existed.
This lifts the restriction for the default mode; User should be able
to start the maximum number of VFs as appear in the PCI config space.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PF updates its VFs' bulletin boards with link configurations whenever
the physical carrier changes or whenever hyper-user explicitly requires
some setting of the VFs link via the hypervisor's PF.
Since the bulletin board is getting cleaned as part of the IOV disable
flow on the PF side, re-enabling sriov would lead to a VF that sees the
carrier as 'down', until an event causing the PF to re-fill the bulletin
with the link configuration would occur.
To fix this we simply refelect the link state during the flows, giving
the later VFs a default reflecting the PFs link state.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During FLR flow, need to make sure HW is no longer capable of writing to
host memory as part of its interrupt mechanisms.
While we're at it, unify the logic cleaning the driver's status-blocks
into using a single API function for both PFs and VFs.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seems like something broke in commit 1408cc1fa4 ("qed: Introduce VFs")
and the function no longer verifies that the vf is indeed a valid one.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent using uninitialized or negative index when handling
steering entries.
Fixes: b12d93d63c ('mlx4: Add support for promiscuous mode in the new steering model.')
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support to specify the MAC address by 'mac-address' or
'local-mac-address' properties in the device tree. These are common
properties for the Ethernet controller.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Mike Sinkovsky <msink@permonline.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This increases TX timeout period from one second to 5 seconds which is
the default value if the driver doesn't explicitly set
net_device->watchdog_timeo.
The one second timeout is too short for W5100 with SPI interface mode
which doesn't support burst READ/WRITE processing in the SPI transfer.
If the packet is transmitted while RX packets are being received at a
very high rate, the TX transmittion work in the workqueue is delayed
and the watchdog timer is expired.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Mike Sinkovsky <msink@permonline.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
W5500 has different bit position for MAC filter in Socket n mode
register from W5100 and W5200.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Mike Sinkovsky <msink@permonline.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The is_w5200() function is not used anymore by the commit which adds
the W5500 support.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Mike Sinkovsky <msink@permonline.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce support in updating statistics of offloaded TC flower
classifiers. Currently only the DROP action is supported.
Signed-off-by: Amir Vadai <amirva@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a counter has the aging flag set when created, it is added to a list
of counters that will be queried periodically from a workqueue. query
result and last use timestamp are cached.
add/del counter must be very efficient since thousands of such
operations might be issued in a second.
There is only a single reference to counters without aging, therefore
no need for locks.
But, counters with aging enabled are stored in a list. In order to make
code as lockless as possible, all the list manipulation and access to
hardware is done from a single context - the periodic counters query
thread.
The hardware supports multiple counters per FTE, however currently we
are using one counter for each FTE.
Signed-off-by: Amir Vadai <amirva@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding a flow steering rule with a counter, need to supply a
destination of type MLX5_FLOW_DESTINATION_TYPE_COUNTER, with a pointer
to a struct mlx5_fc.
Also, MLX5_FLOW_CONTEXT_ACTION_COUNT bit should be set in the action.
Signed-off-by: Amir Vadai <amirva@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Getting packet/byte statistics on flows is done through flow counters.
Implement the firmware commands to alloc, free and query flow counters.
Signed-off-by: Amir Vadai <amirva@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the pxa168_eth driver to use the dma_rmb/wmb calls instead of the
full barriers in order to improve performance: reduced 97ns/39ns on
average in tx/rx path on Marvell BG4CT platform.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since appropriate memory barriers are already there, use the relaxed
version to improve performance a bit.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-05-14
This series contains updates to i40e and i40evf.
Kevin adds support to disable link on all ports and changes bits set
for telling firmware the PHY needs to be modified by the driver.
Anjali adds a feature to enable/disable all multicast for a trusted
VF. Added priv-flag knob to configure global true promiscuous
support.
Shannon adds the support code for calling the admin queue API call
aq_set_switch_config().
Mitch modifies the VF, to log a message if an untrusted VF attempts to
configure promiscuous mode, but lies to it and returns everything is ok
instead of returning an error. Corrects the logic for reporting the
receive packet hash. Fixed the adding of a broadcast filter for VFs,
since that all VSIs are configured to receive broadcasts as default,
so do not need to add a filter.
Catherine refactors the ethtool get_settings to report the possible
supported link modes from what we know about the current PHY type and
that with the firmware supported PHY types.
Jacob changes the driver to use WARN_ONCE in order to highlight the
issue, but do not display a warning every time when receive hang
message is received.
Akeem corrects receive ptype payload layer for non_tunneled IPv6, when
it should be layer 4 for UDP, instead of layer 3.
Dan Carpenter fixes an uninitialized variable bug.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the weaker but more appropriate dma_rmb() to order the reading of
the completion ring.
Suggested-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code is more complicated than necessary and can only report
unsupported SFP+ module if it is plugged in after the device is up.
Rename bnxt_port_module_event() to bnxt_get_port_module_status(). We
already have the current module_status in the link_info structure, so
just check that and report any unsupported SFP+ module status. Delete
the unnecessary last_port_module_event. Call this function at the
end of bnxt_open to report unsupported module already plugged in.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The len value in the hwrm error message is wrong. Use the properly adjusted
value in the variable len.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code has 2 problems:
1. The maximum wait time is not long enough. It is about 60% of the
duration specified by the firmware. It is calling usleep_range(600, 800)
for every 1 msec we are supposed to wait.
2. The granularity of the delay is too coarse. Many simple firmware
commands finish in 25 usec or less.
We fix these 2 issues by multiplying the original 1 msec loop counter by
40 and calling usleep_range(25, 40) for each iteration.
There is also a second delay loop to wait for the last DMA word to
complete. This delay loop should be a very short 5 usec wait.
This change results in much faster bring-up/down time:
Before the patch:
time ip link set p4p1 up
real 0m0.120s
user 0m0.001s
sys 0m0.009s
After the patch:
time ip link set p4p1 up
real 0m0.030s
user 0m0.000s
sys 0m0.010s
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip supports 4K/8K/64K page sizes for the rings and we try to
match it to the CPU PAGE_SIZE. The current page size limits for the rings
are based on 4K/8K page size. If the page size is 64K, these limits are
too large. Reduce them appropriately.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to log a message during driver load indicating PCIe link
speed and width.
The log message will look like this:
bnxt_en 0000:86:00.0 eth0: PCIe: Speed 8.0GT/s Width x8
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to fetch the SFP EEPROM settings from the firmware
and display it via the ethtool -m command. We support SFP+ and QSFP
modules.
v2: Fixed a bug in bnxt_get_module_eeprom() found by Ben Hutchings.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there is only 1 MSI-X vector or in INTA mode, tx and rx pre-set
max channel parameters are shown incorrectly in ethtool -l. With only 1
vector, bnxt_get_max_rings() will return -ENOMEM. bnxt_get_channels
should check this return value, and set max_rx/max_tx to 0 if it is
non-zero.
Signed-off-by: Satish Baddipadige <sbaddipa@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_conntrack_core.c fix in 'net' is not relevant in 'net-next'
because we no longer have a per-netns conntrack hash.
The ip_gre.c conflict as well as the iwlwifi ones were cases of
overlapping changes.
Conflicts:
drivers/net/wireless/intel/iwlwifi/mvm/tx.c
net/ipv4/ip_gre.c
net/netfilter/nf_conntrack_core.c
Signed-off-by: David S. Miller <davem@davemloft.net>
John Crispin