Setting GPIOs' SLPM value to 1 (WAKEUP_DISABLE) is seen to cause
increased power consumption in sleep/deep-sleep. So remove the code
which disables SLPM based on the wakeup settings and only ensure
it is on as needed.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Recent pinctrl discussions concluded that gpiolib APIs should in fact do
whatever is required to mux a GPIO onto pins, by calling pinctrl APIs if
required. This change implements this for the Tegra GPIO driver, and removes
calls to the Tegra-specific APIs from drivers and board files.
Cc: Chris Ball <cjb@laptop.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Chris Ball <cjb@laptop.org> # for sdhci-tegra.c
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
When a Tegra GPIO is used as an IRQ, it should be enabled as a GPIO (so
the pinmux module isn't driving it as an output) and configured as a GPIO
input (so the GPIO module isn't driving it as an output). Set this up
automatically whenever an IRQ is requested, so that users of IRQs don't
need to do this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Fixes the following warning when "SAMSUNG EXYNOS5" is not selected:
warning: ‘exynos5_gpios_1’ defined but not used [-Wunused-variable]
warning: ‘exynos5_gpios_2’ defined but not used [-Wunused-variable]
warning: ‘exynos5_gpios_3’ defined but not used [-Wunused-variable]
warning: ‘exynos5_gpios_4’ defined but not used [-Wunused-variable]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The variable 'bit' is uninitialized in the first iteration of for
loop. Fix it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The irqdomain api changed significantly in v3.4 which caused a build
failure for this driver.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Hans J. Koch <hjk@linutronix.de>
Cc: Torben Hohn <torbenh@linutronix.de>
The code in drivers/of/gpio.c isn't shared by any other subsystem since it
is all gpiolib specific. drivers/gpio is a better place to maintain these
functions.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
This patch converts the drivers in drivers/gpio/* to use
module_pci_driver() macro which makes the code smaller and a bit
simpler by having less boilerplate.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The Kconfig description and help text doesn't list all of the devices
supported by this driver. This patch adds the PCA957x devices.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The boot firmware might leave the registers configured causing interrupts
to happen even when no handler for them is yet registered. Fix this by
clearing the IRQ edge detect registers at init.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Since x86 is using SPARSE_IRQ by default nowadays it means that we need to
allocate IRQ descriptors dynamically using irq_alloc_descs() otherwise the
genirq code fails to convert our irq numbers to suitable descriptors.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Use devm_* helper functions where possible to make the error handling in
the probe function simpler.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Introduce new flags to automatically export GPIOs when using the convenience
functions gpio_request_one() or gpio_request_array(). This eases support for
custom boards where lots of GPIOs need to be exported for customer
applications.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When Tegra30 support was added to the Tegra GPIO driver, a few places
which iterated over all banks were not converted to use the variable
tegra_gpio_bank_count rather than hard-coding the bank count. Fix this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Tegra20 and Tegra30 share the same register layout within registers, but
the addresses of the registers is a little different. Fix the driver to
cope with this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Pull more ARM updates from Russell King.
This got a fair number of conflicts with the <asm/system.h> split, but
also with some other sparse-irq and header file include cleanups. They
all looked pretty trivial, though.
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (59 commits)
ARM: fix Kconfig warning for HAVE_BPF_JIT
ARM: 7361/1: provide XIP_VIRT_ADDR for no-MMU builds
ARM: 7349/1: integrator: convert to sparse irqs
ARM: 7259/3: net: JIT compiler for packet filters
ARM: 7334/1: add jump label support
ARM: 7333/2: jump label: detect %c support for ARM
ARM: 7338/1: add support for early console output via semihosting
ARM: use set_current_blocked() and block_sigmask()
ARM: exec: remove redundant set_fs(USER_DS)
ARM: 7332/1: extract out code patch function from kprobes
ARM: 7331/1: extract out insn generation code from ftrace
ARM: 7330/1: ftrace: use canonical Thumb-2 wide instruction format
ARM: 7351/1: ftrace: remove useless memory checks
ARM: 7316/1: kexec: EOI active and mask all interrupts in kexec crash path
ARM: Versatile Express: add NO_IOPORT
ARM: get rid of asm/irq.h in asm/prom.h
ARM: 7319/1: Print debug info for SIGBUS in user faults
ARM: 7318/1: gic: refactor irq_start assignment
ARM: 7317/1: irq: avoid NULL check in for_each_irq_desc loop
ARM: 7315/1: perf: add support for the Cortex-A7 PMU
...
Primarily gpio device driver changes with some minor side effects
under arch/arm and arch/x86. Also includes a few core changes such as
explicitly supporting (electrical) open source and open drain outputs
and some help for parsing gpio devicetree properties.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=BSW8
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull GPIO changes for v3.4 from Grant Likely:
"Primarily gpio device driver changes with some minor side effects
under arch/arm and arch/x86. Also includes a few core changes such as
explicitly supporting (electrical) open source and open drain outputs
and some help for parsing gpio devicetree properties."
Fix up context conflict due to Laxman Dewangan adding sleep control for
the tps65910 driver separately for gpio's and regulators.
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
gpio/ep93xx: Remove unused inline function and useless pr_err message
gpio/sodaville: Mark broken due to core irqdomain migration
gpio/omap: fix redundant decoding of gpio offset
gpio/omap: fix incorrect update to context.irqenable1
gpio/omap: fix incorrect context restore logic in omap_gpio_runtime_*
gpio/omap: fix missing dataout context save in _set_gpio_dataout_reg
gpio/omap: fix _set_gpio_irqenable implementation
gpio/omap: fix trigger type to unsigned
gpio/omap: fix wakeup_en register update in _set_gpio_wakeup()
gpio: tegra: tegra_gpio_config shouldn't be __init
gpio/davinci: fix enabling unbanked GPIO IRQs
gpio/davinci: fix oops on unbanked gpio irq request
gpio/omap: Fix section warning for omap_mpuio_alloc_gc()
ARM: tegra: export tegra_gpio_{en,dis}able
gpio/gpio-stmpe: Fix the value returned by _get_value routine
Documentation/gpio.txt: Explain expected pinctrl interaction
GPIO: LPC32xx: Add output reading to GPO P3
GPIO: LPC32xx: Fix missing bit selection mask
gpio/omap: fix wakeups on level-triggered GPIOs
gpio/omap: Fix IRQ handling for SPARSE_IRQ
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=onDl
-----END PGP SIGNATURE-----
Merge tag 'mfd_3.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
- 4 new drivers: Freescale i.MX on-chip Anatop, Ricoh's RC5T583 and
TI's TPS65090 and TPS65217.
- New variants support (8420, 8520 ab9540), cleanups and bug fixes for
the abx500 and db8500 ST-E chipsets.
- Some minor fixes and update for the wm8994 from Mark.
- The beginning of a long term TWL cleanup effort coming from the TI
folks.
- Various fixes and cleanups for the s5m, TPS659xx, pm860x, and MAX8997
drivers.
Fix up trivial conflicts due to duplicate patches and header file
cleanups (<linux/device.h> removal etc).
* tag 'mfd_3.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (97 commits)
gpio/twl: Add DT support to gpio-twl4030 driver
gpio/twl: Allocate irq_desc dynamically for SPARSE_IRQ support
mfd: Detach twl6040 from the pmic mfd driver
mfd: Replace twl-* pr_ macros by the dev_ equivalent and do various cleanups
mfd: Micro-optimization on twl4030 IRQ handler
mfd: Make twl4030 SIH SPARSE_IRQ capable
mfd: Move twl-core IRQ allocation into twl[4030|6030]-irq files
mfd: Remove references already defineid in header file from twl-core
mfd: Remove unneeded header from twl-core
mfd: Make twl-core not depend on pdata->irq_base/end
ARM: OMAP2+: board-omap4-*: Do not use anymore TWL6030_IRQ_BASE in board files
mfd: Return twl6030_mmc_card_detect IRQ for board setup
Revert "mfd: Add platform data for MAX8997 haptic driver"
mfd: Add support for TPS65090
mfd: Add some da9052-i2c section annotations
mfd: Build rtc5t583 only if I2C config is selected to y.
mfd: Add anatop mfd driver
mfd: Fix compilation error in tps65910.h
mfd: Add 8420 variant to db8500-prcmu
mfd: Add 8520 PRCMU variant to db8500-prcmu
...
This branch contains a handful of driver updates, mostly to
the LPC32xx platform but also for Samsung EXYNOS and Davinci.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=TkGm
-----END PGP SIGNATURE-----
Merge tag 'drivers2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: More SoC driver updates" from Olof Johansson:
"This branch contains a handful of driver updates, mostly to the
LPC32xx platform but also for Samsung EXYNOS and Davinci.
It had a few context conflicts against patches already merged through
fixes-non-critical. We should have resolved this early during the
development cycle by pulling them in as a dependency, instead I did it
after the fact this time."
* tag 'drivers2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
gpio/samsung: use ioremap() for EXYNOS4 GPIOlib
gpio/samsung: add support GPIOlib for EXYNOS5250
ARM: EXYNOS: add support GPIO for EXYNOS5250
ARM: LPC32xx: Ethernet support
ARM: LPC32xx: USB Support
ARM: davinci: dm644x evm: add support for VPBE display
ARM: davinci: dm644x: add support for v4l2 video display
ARM: EXYNOS: Hook up JPEG PD to generic PD infrastructure
ARM: EXYNOS: Hook up G2D PD to generic PD infrastructure
arm: lpc32xx: phy3250: add rtc & touch device
ARM: LPC32xx: clock.c: Clock registration fixes
ARM: LPC32xx: clock.c: jiffies wrapping
ARM: LPC32xx: clock.c: Missing header file
ARM: LPC32XX: Remove broken non-static declaration
ARM: LPC32xx: clock.c: Fix mutex lock issues
ARM: LPC32xx: clock.c: warning fix
ARM: LPC32xx: Added lpc32xx_defconfig
Pull ARM platform updates from Russell King:
"This covers platform stuff for platforms I have a direct interest in
(iow, I have the hardware). Essentially:
- as we no longer support any other Acorn platforms other than RiscPC
anymore, we can collect all that code into mach-rpc.
- convert Acorn expansion card stuff to use IRQ allocation functions,
and get rid of NO_IRQ from there.
- cleanups to the ebsa110 platform to move some private stuff out of
its header files.
- large amount of SA11x0 updates:
- conversion of private DMA implementation to DMA engine support
(this actually gives us greater flexibility in drivers over the old
API.)
- re-worked ucb1x00 updates - convert to genirq, remove sa11x0
dependencies, fix various minor issues
- move platform specific sa11x0 framebuffer data into platform files
in arch/arm instead of keeping this in the driver itself
- update sa11x0 IrDA driver for DMA engine, and allow it to use DMA
for SIR transmissions as well as FIR
- rework sa1111 support for genirq, and irq allocation
- fix sa1111 IRQ support so it works again
- use sparse IRQ support
After this, I have one more pull request remaining from my current
set, which I think is going to be the most problematical as it
generates 8 conflicts."
Fixed up the trivial conflict in arch/arm/mach-rpc/Makefile as per
Russell.
* 'platforms' of git://git.linaro.org/people/rmk/linux-arm: (125 commits)
ARM: 7343/1: sa11x0: convert to sparse IRQ
ARM: 7342/2: sa1100: prepare for sparse irq conversion
ARM: 7341/1: input: prepare jornada720 keyboard and ts for sa11x0 sparse irq
ARM: 7340/1: rtc: sa1100: include mach/irqs.h instead of asm/irq.h
ARM: sa11x0: remove unused DMA controller definitions
ARM: sa11x0: remove old SoC private DMA driver
USB: sa1111: add hcd .reset method
USB: sa1111: add OHCI shutdown methods
USB: sa1111: reorganize ohci-sa1111.c
USB: sa1111: get rid of nasty printk(KERN_DEBUG "%s: ...", __FILE__)
USB: sa1111: sparse and checkpatch cleanups
ARM: sa11x0: don't static map sa1111
ARM: sa1111: use dev_err() rather than printk()
ARM: sa1111: cleanup sub-device registration and unregistration
ARM: sa1111: only setup DMA for DMA capable devices
ARM: sa1111: register sa1111 devices with dmabounce in bus notifier
ARM: sa1111: move USB interface register definitions to ohci-sa1111.c
ARM: sa1111: move PCMCIA interface register definitions to sa1111_generic.c
ARM: sa1111: move PS/2 interface register definitions to sa1111p2.c
ARM: sa1111: delete unused physical GPIO register definitions
...
These are all specific to some driver. They are typically the platform
side of a change in the drivers directory, such as adding a new driver
or extending the interface to the platform. In cases where there is no
maintainer for the driver, or the maintainer prefers to have the
platform changes in the same branch as the driver changes, the patches
to the drivers are included as well.
A much smaller set of driver updates that depend on other branches
getting merged first will be sent later.
The new export of tegra_chip_uid conflicts with other changes in fuse.c.
In rtc-sa1100.c, the global removal of IRQF_DISABLED conflicts with
the cleanup of the interrupt handling of that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pQ3X
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: driver specific updates" from Arnd Bergmann:
"These are all specific to some driver. They are typically the
platform side of a change in the drivers directory, such as adding a
new driver or extending the interface to the platform. In cases where
there is no maintainer for the driver, or the maintainer prefers to
have the platform changes in the same branch as the driver changes,
the patches to the drivers are included as well.
A much smaller set of driver updates that depend on other branches
getting merged first will be sent later.
The new export of tegra_chip_uid conflicts with other changes in
fuse.c. In rtc-sa1100.c, the global removal of IRQF_DISABLED
conflicts with the cleanup of the interrupt handling of that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up aforementioned trivial conflicts.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: SAMSUNG: change the name from s3c-sdhci to exynos4-sdhci
mmc: sdhci-s3c: add platform data for the second capability
ARM: SAMSUNG: support the second capability for samsung-soc
ARM: EXYNOS: add support DMA for EXYNOS4X12 SoC
ARM: EXYNOS: Add apb_pclk clkdev entry for mdma1
ARM: EXYNOS: Enable MDMA driver
regulator: Remove bq24022 regulator driver
rtc: sa1100: add OF support
pxa: magician/hx4700: Convert to gpio-regulator from bq24022
ARM: OMAP3+: SmartReflex: fix error handling
ARM: OMAP3+: SmartReflex: fix the use of debugfs_create_* API
ARM: OMAP3+: SmartReflex: micro-optimization for sanity check
ARM: OMAP3+: SmartReflex: misc cleanups
ARM: OMAP3+: SmartReflex: move late_initcall() closer to its argument
ARM: OMAP3+: SmartReflex: add missing platform_set_drvdata()
ARM: OMAP3+: hwmod: add SmartReflex IRQs
ARM: OMAP3+: SmartReflex: clear ERRCONFIG_VPBOUNDINTST only on a need
ARM: OMAP3+: SmartReflex: Fix status masking in ERRCONFIG register
ARM: OMAP3+: SmartReflex: Add a shutdown hook
ARM: OMAP3+: SmartReflex Class3: disable errorgen before disable VP
...
Conflicts:
arch/arm/mach-tegra/Makefile
arch/arm/mach-tegra/fuse.c
drivers/rtc/rtc-sa1100.c
Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=o5Xl
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: global cleanups" from Arnd Bergmann:
"Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up trivial conflicts mainly due to #include's being changes on
both sides.
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (121 commits)
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
ARM: EXYNOS: Add clock register addresses for EXYNOS4X12 bus devfreq driver
ARM: EXYNOS: add clock registers for exynos4x12-cpufreq
PM / devfreq: update the name of EXYNOS clock registers that were omitted
PM / devfreq: update the name of EXYNOS clock register
ARM: EXYNOS: change the prefix S5P_ to EXYNOS4_ for clock
ARM: EXYNOS: use static declaration on regarding clock
ARM: EXYNOS: replace clock.c for other new EXYNOS SoCs
ARM: OMAP2+: Fix build error after merge
ARM: S3C24XX: remove call to s3c24xx_setup_clocks
...
Minor removal of an unused inline function and a useless pr_err message.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In preparation to convert SA1100 to sparse irq, set .nr_irqs for each machine
and explicitly include mach/irqs.h as needed.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sodaville driver doesn't build anymore due to the transition to
common irq_domain in the core code. It needs to be reworked, but
the rework isn't trivial. Since this is a new driver anyway for
v3.4, mark it as broken now and a fixup patch can re-enable it when
the rework change has been tested.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add the DT support for the I2C GPIO expander inside the twl4030.
Note: The pdata parameters still have to be properly adapted using
dedicated bindings.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Do not use the board pdata for irq_base, but allocate them dynamically
to allow a proper support of SPARSE_IRQ.
Fix an unneeded line wrap.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
twl4030 is using a two level irq controllers infrastruture.
So far, only the first level was using dynamic irq_desc allocation
to be able to have irq_domain support for device tree.
There is a need to allocate separate irq_descs for the SIH too to
avoid hacking the first level with interrupts from the second level.
Add an irq_base parameter to allow the caller to provide the base from
pdata or from dynamic allocation.
Affect TWL4030_NR_IRQS to the twl-core IRQs only.
Moreover that will allow the extraction of the of_node pointer for further
Device Tree conversion.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Pull powerpc merge from Benjamin Herrenschmidt:
"Here's the powerpc batch for this merge window. It is going to be a
bit more nasty than usual as in touching things outside of
arch/powerpc mostly due to the big iSeriesectomy :-) We finally got
rid of the bugger (legacy iSeries support) which was a PITA to
maintain and that nobody really used anymore.
Here are some of the highlights:
- Legacy iSeries is gone. Thanks Stephen ! There's still some bits
and pieces remaining if you do a grep -ir series arch/powerpc but
they are harmless and will be removed in the next few weeks
hopefully.
- The 'fadump' functionality (Firmware Assisted Dump) replaces the
previous (equivalent) "pHyp assisted dump"... it's a rewrite of a
mechanism to get the hypervisor to do crash dumps on pSeries, the
new implementation hopefully being much more reliable. Thanks
Mahesh Salgaonkar.
- The "EEH" code (pSeries PCI error handling & recovery) got a big
spring cleaning, motivated by the need to be able to implement a
new backend for it on top of some new different type of firwmare.
The work isn't complete yet, but a good chunk of the cleanups is
there. Note that this adds a field to struct device_node which is
not very nice and which Grant objects to. I will have a patch soon
that moves that to a powerpc private data structure (hopefully
before rc1) and we'll improve things further later on (hopefully
getting rid of the need for that pointer completely). Thanks Gavin
Shan.
- I dug into our exception & interrupt handling code to improve the
way we do lazy interrupt handling (and make it work properly with
"edge" triggered interrupt sources), and while at it found & fixed
a wagon of issues in those areas, including adding support for page
fault retry & fatal signals on page faults.
- Your usual random batch of small fixes & updates, including a bunch
of new embedded boards, both Freescale and APM based ones, etc..."
I fixed up some conflicts with the generalized irq-domain changes from
Grant Likely, hopefully correctly.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (141 commits)
powerpc/ps3: Do not adjust the wrapper load address
powerpc: Remove the rest of the legacy iSeries include files
powerpc: Remove the remaining CONFIG_PPC_ISERIES pieces
init: Remove CONFIG_PPC_ISERIES
powerpc: Remove FW_FEATURE ISERIES from arch code
tty/hvc_vio: FW_FEATURE_ISERIES is no longer selectable
powerpc/spufs: Fix double unlocks
powerpc/5200: convert mpc5200 to use of_platform_populate()
powerpc/mpc5200: add options to mpc5200_defconfig
powerpc/mpc52xx: add a4m072 board support
powerpc/mpc5200: update mpc5200_defconfig to fit for charon board
Documentation/powerpc/mpc52xx.txt: Checkpatch cleanup
powerpc/44x: Add additional device support for APM821xx SoC and Bluestone board
powerpc/44x: Add support PCI-E for APM821xx SoC and Bluestone board
MAINTAINERS: Update PowerPC 4xx tree
powerpc/44x: The bug fixed support for APM821xx SoC and Bluestone board
powerpc: document the FSL MPIC message register binding
powerpc: add support for MPIC message register API
powerpc/fsl: Added aliased MSIIR register address to MSI node in dts
powerpc/85xx: mpc8548cds - add 36-bit dts
...
In gpio_get(), _get_gpio_datain() and _get_gpio_dataout() get rid of
un-necessary operation to compute gpio mask. The gpio offset passed
to gpio_get() is sufficient to do that.
Here is Russell's original comment:
Can someone explain to me this:
static int _get_gpio_datain(struct gpio_bank *bank, int gpio)
{
void __iomem *reg = bank->base + bank->regs->datain;
return (__raw_readl(reg) & GPIO_BIT(bank, gpio)) != 0;
}
static int gpio_get(struct gpio_chip *chip, unsigned offset)
{
struct gpio_bank *bank = container_of(chip, struct gpio_bank, chip);
void __iomem *reg = bank->base;
int gpio = chip->base + offset;
u32 mask = GPIO_BIT(bank, gpio);
if (gpio_is_input(bank, mask))
return _get_gpio_datain(bank, gpio);
else
return _get_gpio_dataout(bank, gpio);
}
Given that bank->width on OMAP is either 32 or 16, and GPIO numbers for
any GPIO chip are always aligned to 32 or 16, why does this code bother
adding the chips base gpio number and then modulo the width?
Surely this means if - for argument sake - you registered a GPIO chip
with 8 lines followed by one with 16 lines, GPIO0..7 would be chip 0
bit 0..7, GPIO8..15 would be chip 1 bit 8..15, GPIO16..23 would be
chip 1 bit 0..7.
However, if you registered a GPIO chip with 16 lines first, it would
mean GPIO0..15 would be chip 0 bit 0..15, and GPIO16..31 would be
chip 1 bit 0..15.
Surely this kind of behaviour is not intended?
Is there a reason why the bitmask can't just be (1 << offset) where
offset is passed into these functions as GPIO number - chip->base ?
Reported-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In _enable_gpio_irqbank() when bank->regs->set_irqenable is TRUE,
gpio_mask can be directly set by writing to set_irqenable register
without overwriting current value. In order to ensure the same is
stored in context.irqenable1, we must avoid overwriting it with
gpio_mask at the end of the function. Instead, update irqenable1
appropriately by OR'ing with gpio_mask.
For the case where bank->regs->set_irqenable is FALSE, irqenable1
can be directly overwritten with 'l' which holds correct computed
value.
if (bank->regs->set_irqenable) {
reg += bank->regs->set_irqenable;
l = gpio_mask;
} else {
reg += bank->regs->irqenable;
l = __raw_readl(reg);
if (bank->regs->irqenable_inv)
l &= ~gpio_mask;
else
l |= gpio_mask;
}
Make similar change for _disable_gpio_irqbank().
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In omap_gpio_runtime_suspend/resume() the context save/restore should
be independent of bank->enabled_non_wakeup_gpios. This was preventing
context restore of GPIO lines which are not wakeup enabled.
Reported-by: Govindraj Raja <govindraj.raja@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
There are two functions, _set_gpio_dataout_reg() and _set_gpio_dataout_mask()
which writes to dataout register and the dataout context must be saved.
It is missing in the first function, _set_gpio_dataout_reg(). Fix this.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This function should be capable of both enabling and disabling interrupts
based upon the *enable* parameter. Right now the function only enables
the interrupt and *enable* is not used at all. So add the interrupt
disable capability also using the parameter.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The GPIO trigger parameter is of type unsigned.
enum {
IRQ_TYPE_NONE = 0x00000000,
IRQ_TYPE_EDGE_RISING = 0x00000001,
IRQ_TYPE_EDGE_FALLING = 0x00000002,
IRQ_TYPE_EDGE_BOTH = (IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING),
IRQ_TYPE_LEVEL_HIGH = 0x00000004,
IRQ_TYPE_LEVEL_LOW = 0x00000008,
IRQ_TYPE_LEVEL_MASK = (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_LEVEL_HIGH),
IRQ_TYPE_SENSE_MASK = 0x0000000f,
IRQ_TYPE_PROBE = 0x00000010,
...
};
Even though gpio_irq_type(struct irq_data *d, unsigned type) has the right type
of parameter, the subsequent called functions set_gpio_triggering() and
set_gpio_trigger() wrongly makes it signed integer. Fix this.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
There are two ways through which wakeup_en register can be programmed
using gpiolib APIs as shown below. It is seen that in the second case
in _set_gpio_wakeup(), even though bank->suspend_wakeup is updated
correctly, its value is not programmed in wakeup_en register. Fix this.
irq_set_type()->gpio_irq_type()->_set_gpio_triggering()->set_gpio_trigger()
irq_set_wake()->gpio_wake_enable()->_set_gpio_wakeup()
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This function is called from non-__init context, just like
tegra_gpio_enable()/disable(). Remove the __init annotation to avoid
section mismatch warnings during compile.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Initial board support for the GE IMP3A, a 3U compactPCI card with a p2020
processor.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The GE GPIO driver provides basic support (set direction, read/write state)
for the GPIO provided on some GE single board computers. This patch moves
the driver from the 86xx specific platform directrory to the GPIO subsystem
so that it can be used on non-86xx boards.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'next/soc-exynos5250-gpio' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (201 commits)
gpio/samsung: use ioremap() for EXYNOS4 GPIOlib
gpio/samsung: add support GPIOlib for EXYNOS5250
ARM: EXYNOS: add support GPIO for EXYNOS5250
(update to v3.3-rc7)
Conflicts:
arch/arm/mach-pxa/pxa25x.c
arch/arm/mach-pxa/pxa27x.c
The dummy clock for the pxa rtc in those files keeps getting added and
removed in various trees. Apparently removing is the correct solution.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'ep93xx-for-arm-soc' of git://github.com/RyanMallon/linux-2.6:
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
(update to v3.3-rc7)
Conflicts:
arch/arm/mach-s3c2440/common.h
This patch changes to use ioremap() for EXYNOS4210
so that we can drop the static mapping for EXYNOS
SoCs.
Note: Will be updated for all of Samsung GPIOlibs
to use ioremap() next time.
Signed-off-by: Sangsu Park <sangsu4u.park@samsung.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds gpio_chips for EXYNOS5250 and replaces
exynos4_xxx() with exynos_xxx() and variables to support
exynos4 and exynos5 together.
In addition, use ioreamp() for base address of gpios.
Signed-off-by: Sangsu Park <sangsu4u.park@samsung.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Move the pinmux setting of the EP93xx GPIOs to the core code. This
removes the need for the GPIO driver to have access to the system
controller registers.
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Hartley Sweeten <hsweeten@visionengravers.com>
Unbanked GPIO IRQ handling code made a copy of just
the irq_chip structure for GPIO IRQ lines which caused
problems after the generic IRQ chip conversion because
there was no valid irq_chip_type structure with the
right "regs" populated. irq_gc_mask_set_bit() was
therefore accessing random addresses.
Fix it by making a copy of irq_chip_type structure
instead. This will ensure sane register offsets.
Cc: <stable@vger.kernel.org> # v3.0.x+
Reported-by: Jon Povey <Jon.Povey@racelogic.co.uk>
Tested-by: Jon Povey <Jon.Povey@racelogic.co.uk>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Make omap_mpuio_alloc_gc() __devinit as omap_gpio_chip_init()
is __devinit. Otherwise we get:
WARNING: vmlinux.o(.devinit.text+0xa10): Section mismatch in reference
from the function omap_gpio_chip_init() to the function .init.text:omap_mpuio_alloc_gc()
The function __devinit omap_gpio_chip_init() references
a function __init omap_mpuio_alloc_gc().
If omap_mpuio_alloc_gc is only used by omap_gpio_chip_init then
annotate omap_mpuio_alloc_gc with a matching annotation.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
These two functions are used in drivers that can be
modules, so they need to be exported.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alan Ott <alan@signal11.us>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The present _get_value routine returns the contents of the GPIO Monitor Pin
Status Register(GPMR) starting from the bit whose value is requested to BIT 0
(irrelevant bits are replace by 0).
For e.g. if we request the value of GPIO 6 in the earlier implementation the
value returned is:
BIT6 followed by 6 0's
whereas it should just return BIT6.
This patch addresses the same.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The chip offers the function to detect the current state of output of the GPO
P3 pins. Useful for reading GPIO output state in Linux' GPIO API, e.g. via
sysfs.
Please note that this only reads back the currently programmed output state,
not the actual electrical level in terms of a GPI function. Finally, GPO3 is
still just an output.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add missing mask to pin bit selection in gpio-lpc32xx.c
(#define GPIO3_PIN_IN_SEL)
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
While both level- and edge-triggered GPIOs are capable of generating
interrupts, only edge-triggered GPIOs are capable of generating a
module-level wakeup to the PRCM (c.f. 34xx NDA TRM section 25.5.3.2.)
In order to ensure that devices using level-triggered GPIOs as
interrupts can also cause wakeups (e.g. from idle), this patch enables
edge-triggering for wakeup-enabled, level-triggered GPIOs when a GPIO
bank is runtime-suspended (which also happens during idle.)
This fixes a problem found in GPMC-connected network cards with GPIO
interrupts (e.g. smsc911x on Zoom3, Overo, ...) where network booting
with NFSroot was very slow since the GPIO IRQs used by the NIC were
not generating PRCM wakeups, and thus not waking the system from idle.
NOTE: until v3.3, this boot-time problem was somewhat masked because
the UART init prevented WFI during boot until the full serial driver
was available. Preventing WFI allowed regular GPIO interrupts to fire
and this problem was not seen. After the UART runtime PM cleanups, we
no longer avoid WFI during boot, so GPIO IRQs that were not causing
wakeups resulted in very slow IRQ response times.
Tested on platforms using level-triggered GPIOs for network IRQs using
the SMSC911x NIC: 3530/Overo and 3630/Zoom3.
Reported-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Adds support for boards which have an STMPE GPIO device without the
interrupt pin connected. This means that no interrupt can be received
but the GPIO pins can still be driven and read.
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Michel Jaouen <michel.jaouen@stericsson.com>
Signed-off-by: Chris Blair <chris.blair@stericsson.com>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The driver is still relying on internal OMAP IRQ defines that
are not relevant anymore if OMAP is built with SPARSE_IRQ.
Replace the defines with the proper IRQ base number.
Clean some comment style issue.
Remove some hidden and ugly cpu_class_is_omap1() inside the
gpio header.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Tested-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Adapt the GPIO driver to retrieve information from a DT file.
Allocate the irq_base dynamically and rename bank->virtual_irq_start
to bank->irq_base.
Change irq_base type to int instead of u16 to match irq_alloc_descs
output.
Add documentation for GPIO properties specific to OMAP.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Replace the regular kzalloc and ioremap with the devm_ equivalent
to simplify error handling.
Add the missing devm_request_mem_region to reserve the region used
by the driver.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
The driver does not need anymore any id to identify the GPIO instance.
Remove every occurence of the bank->id inside the driver.
Remove two trailing spaces.
Add a dev variable for better readability in probe.
Remove unused variable bank->pbase.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
I've seen users getting very confused by the WARN_ON()s for can_sleep
GPIOs in the atomic-safe paths, the discoverability of the non-atomic
version of the API seems to be hampered by the fact that it's defined
in a header file not the .c file where the warnings are.
Add a couple of comments next to the warnings to help people on their
way.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Adding support for the open source gpio on which client
can specify the open source property through GPIO flag
GPIOF_OPEN_SOURCE at the time of gpio request.
The open source pins are normally pulled low and it
cannot be driven to output with value of 0 and so
when client request for setting the pin to LOW, the
gpio will be set to input direction to make pin in tristate
and hence PULL-DOWN on pins will make the state to LOW.
The open source pin can be driven to HIGH by setting output
with value of 1.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Adding support for the open drain gpio on which client
can specify the open drain property through GPIO flag
GPIOF_OPEN_DRAIN at the time of gpio request.
The open drain pins are normally pulled high and it
cannot be driven to output with value of 1 and so
when client request for setting the pin to HIGH, the
gpio will be set to input direction to make pin in tristate
and hence PULL-UP on pins will make the state to HIGH.
The open drain pin can be driven to LOW by setting output
with value of 0.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tegra SoC driver support.
Some device tree conversions, some new drivers. and a fix for an issue
introduced in Grant Likely's irq_domain conversion in his tree. Because
of that, this branch depends on his branch to build (but not to merge):
git://git.secretlab.ca/git/linux-2.6.git irqdomain/next
* tag 'tegra-soc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra: (34 commits)
ARM: tegra: uncompress.h: Don't depend on kernel headers
gpio: tegra: Fix build issue due to irq_domain rework.
ARM: tegra: Remove duplicate PMU interrupt inversion code
ARM: tegra: Add a simple PMC driver
ARM: tegra: dma: not required to move requestor when stopping.
ARM: tegra: Fix EMC pdata initialization from registers
gpio: tegra: Parameterize the number of banks
gpio: tegra: Dynamically allocate IRQ base, and support DT
ARM: tegra: Remove use of TEGRA_GPIO_TO_IRQ
ARM: tegra: Pass uncompress.h UART selection to DEBUG_LL
ARM: tegra: uncompress.h: Choose a UART at runtime
ARM: tegra: uncompress.h: Store UART address in a variable
ARM: tegra: Introduce define DEBUG_UART_SHIFT
ARM: tegra: Support Tegra30 in decompressor UART setup
ARM: tegra: Pause DMA when reading transfer count
ARM: tegra: emc: device tree support
ARM: tegra: emc: convert tegra2_emc to a platform driver
ARM: tegra: fuse: add bct strapping reading
ARM: tegra: fuse: add functions to access chip revision
ARM: tegra: fuse: use apbio dma for register access
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/mach-omap1/gpio16xx.c
drivers/gpio/gpio-omap.c
Merge in the runtime-pm-cleanup branch from the gpio tree into
next/cleanup, this resolves a nonobvious merge conflict between
the two branches. Both branches move parts of the gpio-omap
driver into platform code, this takes the superset of both
changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 7da5a66 "irq_domain: Remove 'new' irq_domain in favour of the
ppc one" changed the set of available irq domain APIs. Update the Tegra
GPIO driver to account for those changes, to solve a build break.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This way we can remove omap_read/write call from the GPIO driver
and remove include to linux/io.h.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Lindgren <tony@atomide.com>
pl061 uses same routines for suspend/freeze/poweroff and resume/thaw/restore.
We are only saving and restoring register values on these routines.
During hibernation, in freeze() we take a snapshot of gpio registers. In thaw()
we don't actually need to restore these registers, as power was never shut down
till now. Similarly, in poweroff() we don't need to take snapshot of these
registers again, as it was done during freeze() and by now the image is already
saved on disk.
This patch passes poweroff() and thaw() routines as NULL to avoid this extra
work done.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch converts a number of the powerpc drivers to use the common library
of irq_domain xlate functions, dropping a bunch of lines in the process.
v5: - Remove tsi108 changes from patch
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
Each revmap type has different arguments for setting up the revmap.
This patch splits up the generator functions so that each revmap type
can do its own setup and the user doesn't need to keep track of how
each revmap type handles the arguments.
This patch also adds a host_data argument to the generators. There are
cases where the host_data pointer will be needed before the function returns.
ie. the legacy map calls the .map callback for each irq before returning.
v2: - Add void *host_data argument to irq_domain_add_*() functions
- fixed failure to compile
- Moved IRQ_DOMAIN_MAP_* defines into irqdomain.c
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
This patch drops the powerpc-specific irq_host structures and uses the common
irq_domain strucutres defined in linux/irqdomain.h. It also fixes all
the users to use the new structure names.
Renaming irq_host to irq_domain has been discussed for a long time, and this
patch is a step in the process of generalizing the powerpc virq code to be
usable by all architecture.
An astute reader will notice that this patch actually removes the irq_host
structure instead of renaming it. This is because the irq_domain structure
already exists in include/linux/irqdomain.h and has the needed data members.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
Tegra20's GPIO controller has 7 banks, and Tegra30's controller has 8
banks. Allow the number of banks to be configured at run-time by the
device tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Olof Johansson <olof@lixom.net>
Enhance the driver to dynamically allocate the base IRQ number, and
create an IRQ domain for itself. The use of an IRQ domain ensures that
any device tree node interrupts properties are correctly parsed.
Describe interrupt-related properties in the device tree binding docs,
and the contents of "child" node interrupts property.
Update tegra*.dtsi to specify the required interrupt-related properties.
Finally, remove the definition of TEGRA_GPIO_TO_IRQ; this macro no longer
gives correct results since the IRQ numbers for GPIOs are dynamically
allocated.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Olof Johansson <olof@lixom.net>
GPIO IP revisions such as those used in OMAP4 have a set_dataout
while the previous revisions used a single dataout register.
Depending on what is available restore the dataout settings
to the right register.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Setup the dataout register before restoring OE. This is to make
sure that we have valid data in dataout register which would be
made available in output pins as soon as OE is enabled. Else,
there is risk of unknown data getting out into gpio pins.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Setup the interrupt enable registers only after we have configured the
required edge and required configurations, not before, to prevent
spurious events as part of restore routine.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
GPIO debounce registers need to be saved and restored for proper functioning
of driver.
Signed-off-by: Nishanth Menon <nm@ti.com>
tarun.kanti@ti.com: Debounce context save is moved to _set_gpio_debounce()
as part of dynamic context save to remove overhead.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Context is now saved dynamically in respective functions whenever and
whichever registers are modified. This avoid overhead of saving all
registers context in the runtime suspend callback.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Enable debounce clock before writing/reading debounce registers.
Disable the clock at the end so that it is synchronized with the
pm_runtime_get/put_sync calls.
Enable debounce clock per module. This call is mandatory because
in omap_gpio_request() when *_runtime_get_sync() is called,
_gpio_dbck_enable() within runtime callbck fails to turn on dbck
because dbck_enable_mask used within _gpio_dbck_enable() is still
not initialized at that point. Therefore we have to enable dbck here.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The dbck_enable_mask indicates which all GPIOs within a bank have debounce
enabled and dbck is enabled/disabled based upon this. But there is no
mechanism to track the dbck state. In order to manage the dbck state we need
additional flag and logic so that turning off/on dbck is synchronized with
pm_runtime_put/get_sync calls.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Since *_prepare_for_idle() and *_resume_after_idle() are called
with interrupts disabled they should be kept as simple as possible.
So, moving most of the stuff to *_runtime_suspend/resume() callbacks.
To avoid invalid context restore happening in *_runtime_resume()
callback as a result of *_get_sync() call in *_gpio_probe(), update
bank->context_loss_count. This would make context restore condition
check false in the callback and skip restore until further
initialization take place. The workaround_enabled static variable
is now a member of struct gpio_bank.
Unlike most GPIO registers the OE has 0xffffffff as the default value.
To make sure invalid context is not restored, updating the OE context
with default value.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
There is no need to operate on all the banks every time the function is called.
Just operate on the current bank passed by the framework.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Call runtime pm APIs pm_runtime_get_sync() and pm_runtime_put()
for enabling/disabling clocks appropriately. Remove syscore_ops and
instead use SET_RUNTIME_PM_OPS macro.
There is no more need to call omap_device_disable_idle_on_suspend
since driver is PM runtime adapted now.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The only bank->type (method) used in the OMAP GPIO driver is MPUIO type as they
need to be handled separately. Identify the same using a flag and remove all
METHOD_* macros.
mpuio_init() function is defined under #ifdefs. It is required only in case
of MPUIO bank type and only when PM operations are supported by it.
This is applicable only in case of OMAP16xx SoC's MPUIO GPIO bank type.
For all the other cases it is a dummy function. Hence clean up the same
and remove all the OMAP SoC specific #ifdefs.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove un-necessary bit masking. Since the register are 4 byte aligned
and readl would work as is. The 'enabled' mask is already taking care
to mask for bank width.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Use regs->pinctrl field instead of using the macro OMAP1510_GPIO_PIN_CONTROL
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
With register offsets now defined for respective OMAP versions we can get rid
of cpu_class_* checks. This function now has common initialization code for
all OMAP versions. Initialization specific to OMAP16xx has been moved within
omap16xx_gpio_init().
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Getting rid of ifdefs within the function by adding register offset intctrl
and associating OMAPXXXX_GPIO_INT_CONTROL in respective SoC specific files.
Also, use wkup_status register consistently instead of referring to wakeup
clear and wakeup set register offsets. Get rid of cpu_is_xxxx checks in
set_gpio_trigger() using irqctrl.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
It is not required to use hard-coded offsets any more in context save and
restore functions and instead use the generic offsets which have been correctly
initialized during device registration.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
By adding level and edge detection register offsets and then initializing them
correctly according to OMAP versions during device registrations we can now remove
lot of revision checks in these functions.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Wakeup enable register offset initialized according to OMAP versions
during device registration. Use this to avoid version checks.
Starting with OMAP4, legacy registers should not be used in combination
with the updated regsiters. Use wkup_en register consistently for
all SoCs wherever applicable.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove cpu-is checks while enabling/disabling OMAP GPIO module during a gpio
request/free.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Non-wakeup GPIOs are available only in OMAP2. Avoid cpu_is checks by making
non_wakeup_gpios as part of pdata.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Modify omap_gpio_prepare_for_idle() & omap_gpio_resume_after_idle() functions
to handle save context & restore context respectively in the OMAP GPIO driver
itself instead of calling these functions from pm specific files.
For this, in gpio_prepare_for_idle(), call *_get_context_loss_count() and in
gpio_resume_after_idle() call it again. If the count is different, do restore
context.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Currently gpio_context array used to save gpio bank's context, is used only for
OMAP3 architecture. Move gpio_context as part of gpio_bank structure so that it
can be specific to each gpio bank and can be used for any OMAP architecture
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In omap3, save/restore context is implemented for GPIO banks 2-6 as GPIO bank1
is in wakeup domain. Instead of identifying bank's power domain by bank id,
use 'loses_context' flag which is filled by pwrdm_can_ever_lose_context()
during dev_init.
For getting the powerdomain pointer, omap_hwmod_get_pwrdm() is used.
omap_device_get_pwrdm() could not be used as the pwrdm information needs to be
filled in pdata, whereas omap_device_get_pwrdm() could be used only after
omap_device_build() call.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The gpio_bank_count is the count of number of GPIO devices in a SoC. Remove this
dependency from the driver by using list. Also remove the dependency on array of
pointers to gpio_bank struct of all GPIO devices.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The device tps65910/tps65911 supports the sleep
functionality in some of gpios. If gpio is configured
in output mode and sleep is enabled then during device
sleep state, the output of gpio becomes LOW regardless
of non-sleep output value.
Such gpio can be used to control regulator switch such
that output of regulator is off in device sleep state.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Sodaville has GPIO controller behind the PCI bus. To my suprissed it is
not the same as on PXA.
The interrupt & gpio chip can be referenced from the device tree like
from any other driver. Unfortunately the driver which uses the gpio
interrupt has to use irq_of_parse_and_map() instead of
platform_get_irq(). The problem is that the platform device (which is
created from the device tree) is most likely created before the
interrupt chip is registered and therefore irq_of_parse_and_map() fails.
In theory the driver works as module. In reality most of the irq
functions are not exported to modules and it is possible that _this_
module is unloaded while the provided irqs are still in use.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
[torbenh@linutronix.de: make it work after the irq namespace cleanup,
add some device tree entries.]
Signed-off-by: Torben Hohn <torbenh@linutronix.de>
[bigeasy@linutronix.de: convert to generic irq & gpio chip]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
[grant.likely@secretlab.ca: depend on x86 to avoid irq_domain breakage]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This bug was introduced by commit 54be5663
"gpio-ml-ioh: Support interrupt function" which adds a spinlock to struct
ioh_gpio but never init the spinlock.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This bug was introduced by commit d568a681
"gpio-pch: add spinlock in suspend/resume processing"
which adds a spinlock to struct pch_gpio but never init the spinlock.
Reported-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Commit 15c9a0acc3 (of: create of_phandle_args to simplify return of phandle
parsing data) modifies the parameter list of of_xlate function pointer declaration
in gpio_chip. Adapt the gpio specifier translate function for this change.
Reported-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Tested-by: Karol Lewandowski <k.lewandowsk@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
we only use the gpio function of mc9s08dz60 mcu chip, so just
add the gpio driver, as this mcu will never be used in other board.
Signed-off-by: Wu Guoxing <b39297@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In preparation to make mach/irqs.h optional and remove from asm/irq.h,
directly include mach/irq.h to get MMP_GPIO_TO_IRQ and PXA_GPIO_TO_IRQ.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
One of the GPIO names in drivers/gpio/gpio-lpc32xx.c
was bad. Renaming gpi000 -> gpio00
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Using the correct gpio offset for setting the initial value
of gpio when setting output direction.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This driver does an unconditional read of io space during module init which
causes a bad dereference on ARM. It looks to me like this is an x86 only
drivers, so restrict it to only compile on x86.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Denis Turischev <denis@compulab.co.il>
The __iomem annotation is to be used together with pointers used
in iowrite32() but not for pointers returned by kzalloc().
For more details see [1] and [2].
This patch will remove the following sparse warning (i.e. when
copiling with "make C=1"):
* warning: incorrect type in assignment (different address spaces)
References:
[1] A new I/O memory access mechanism (Sep 15, 2004)
http://lwn.net/Articles/102232/
[2] Being more anal about iospace accesses (Sep 15, 2004)
http://lwn.net/Articles/102240/
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch will remove the following sparse warning ("make C=1"):
* warning: Using plain integer as NULL pointer
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The __iomem annotation is to be used together with pointers used
as iowrite32() parameter. For more details see [1] and [2].
This patch will remove the following sparse warnings ("make C=1"):
* warning: incorrect type in assignment (different address spaces)
* warning: incorrect type in argument 1 (different address spaces)
* warning: incorrect type in argument 2 (different address spaces)
References:
[1] A new I/O memory access mechanism (Sep 15, 2004)
http://lwn.net/Articles/102232/
[2] Being more anal about iospace accesses (Sep 15, 2004)
http://lwn.net/Articles/102240/
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch will remove the following sparse warning ("make C=1"):
* warning: Using plain integer as NULL pointer
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The existing gpio_to_irq() implementation on sa1100 only translates
validly for internal GPIOs. Since this sub-arch enables GPIOLIB
support, this results in buggy translations for non-internal GPIOs.
Get rid of the private gpio_to_irq() implementation, replacing it
with the .to_irq method in the sa1100 gpio chip instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
rtc: max8925: Add function to work as wakeup source
mfd: Add pm ops to max8925
mfd: Convert aat2870 to dev_pm_ops
mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
mfd: Introduce missing kfree in 88pm860x probe routine
mfd: Add S5M series configuration
mfd: Add s5m series irq driver
mfd: Add S5M core driver
mfd: Improve mc13xxx dt binding document
mfd: Fix stmpe section mismatch
mfd: Fix stmpe build warning
mfd: Fix STMPE I2c build failure
mfd: Constify aat2870-core i2c_device_id table
gpio: Add support for stmpe variant 801
mfd: Add support for stmpe variant 801
mfd: Add support for stmpe variant 610
mfd: Add support for STMPE SPI interface
mfd: Separate out STMPE controller and interface specific code
misc: Remove max8997-muic sysfs attributes
mfd: Remove unused wm831x_irq_data_to_mask_reg()
...
Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (31 commits)
pinctrl: remove unnecessary max pin number
pinctrl: correct a offset while enumerating pins
pinctrl: some typo fixes
pinctrl: rename U300 and SIRF pin controllers
pinctrl: pass name instead of device to pin_config_*
pinctrl: add "struct seq_file;" to pinconf.h
pinctrl: conjure names for unnamed pins
pinctrl: add a group-specific hog macro
pinctrl: don't create a device for each pin controller
arm/u300: don't use PINMUX_MAP_PRIMARY*
pinctrl: implement PINMUX_MAP_SYS_HOG
pinctrl: add a pin config interface
pinctrl/coh901: driver to request its pins
pinctrl: u300-pinmux: register proper GPIO ranges
pinctrl: move the U300 GPIO driver to pinctrl
ARM: u300: localize GPIO assignments
pinctrl: make it possible to add multiple maps
pinctrl: make a copy of pinmux map
pinctrl: GPIO direction support for muxing
pinctrl: print pin range in GPIO range debugs
...
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vPhu
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Driver specific changes
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
ARM: sa1100: clean up of the clock support
ARM: pxa: add dummy clock for sa1100-rtc
RTC: sa1100: support sa1100, pxa and mmp soc families
RTC: sa1100: remove redundant code of setting alarm
RTC: sa1100: Clean out ost register
Input: zylonite-wm97xx - replace IRQ_GPIO() with gpio_to_irq()
pcmcia: pxa: replace IRQ_GPIO() with gpio_to_irq()
ARM: EXYNOS: Modified files for SPI consolidation work
ARM: S5P64X0: Enable SDHCI support
ARM: S5P64X0: Add lookup of sdhci-s3c clocks using generic names
ARM: S5P64X0: Add HSMMC setup for host Controller
ARM: EXYNOS: Add USB OHCI support to ORIGEN board
USB: Add Samsung Exynos OHCI diver
ARM: EXYNOS: Add USB OHCI support to SMDKV310 board
ARM: EXYNOS: Add USB OHCI device
net: macb: fix build break with !CONFIG_OF
i2c: tegra: Support DVC controller in device tree
i2c: tegra: Add __devinit/exit to probe/remove
net/at91_ether: use gpio_is_valid for phy IRQ line
ARM: at91/net: add macb ethernet controller in 9g45/9g20 DT
...
Both platforms had some initial device tree support, but this adds
much more to actually make it usable.
This is where the really nasty conflicts in the samsung platform
start, due to some files getting moved around and combined in the
'restart' branch that has already gone into mainline through
Russell's tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=XY2N
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Device tree conversions for samsung and tegra
Both platforms had some initial device tree support, but this adds
much more to actually make it usable.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
ARM: dts: Add intial dts file for EXYNOS4210 SoC, SMDKV310 and ORIGEN
ARM: EXYNOS: Add Exynos4 device tree enabled board file
rtc: rtc-s3c: Add device tree support
input: samsung-keypad: Add device tree support
ARM: S5PV210: Modify platform data for pl330 driver
ARM: S5PC100: Modify platform data for pl330 driver
ARM: S5P64x0: Modify platform data for pl330 driver
ARM: EXYNOS: Add a alias for pdma clocks
ARM: EXYNOS: Limit usage of pl330 device instance to non-dt build
ARM: SAMSUNG: Add device tree support for pl330 dma engine wrappers
DMA: PL330: Add device tree support
ARM: EXYNOS: Modify platform data for pl330 driver
DMA: PL330: Infer transfer direction from transfer request instead of platform data
DMA: PL330: move filter function into driver
serial: samsung: Fix build for non-Exynos4210 devices
serial: samsung: add device tree support
serial: samsung: merge probe() function from all SoC specific extensions
serial: samsung: merge all SoC specific port reset functions
ARM: SAMSUNG: register uart clocks to clock lookup list
serial: samsung: remove all uses of get_clksrc and set_clksrc
...
Fix up fairly trivial conflicts in arch/arm/mach-s3c2440/clock.c and
drivers/tty/serial/Kconfig both due to just adding code close to
changes.
STMPE801 is a GPIO expander. GPIO registers for 801 are slightly different from other
variants. This patch adds support for STMPE801 in stmpe gpio driver.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: (36 commits)
mfd: Clearing events requires event registers to be writable for da9052-core
mfd: Fix annotations in da9052-core
gpiolib: Mark da9052 driver broken
mfd: Declare da9052_regmap_config for the bus drivers
MFD: DA9052/53 MFD core module add SPI support v2
MFD: DA9052/53 MFD core module
regmap: Add irq_base accessor to regmap_irq
regmap: Allow drivers to reinitialise the register cache at runtime
regmap: Add trace event for successful cache reads
regmap: Allow regmap_update_bits() users to detect changes
regmap: Report if we actually handled an interrupt in regmap-irq
regmap: Fix rbtreee build when not using debugfs
regmap: Provide debugfs dump of the rbtree cache data
regmap: Do debugfs init before cache init
regmap: Suppress noop writes in regmap_update_bits()
regmap: Remove indexed cache type
regmap: Drop check whether a register is readable in regcache_read
regmap: Properly round cache_word_size
regmap: Add support for 10/14 register formating
regmap: Try cached read before checking if a hardware read is possible
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (53 commits)
Kconfig: acpi: Fix typo in comment.
misc latin1 to utf8 conversions
devres: Fix a typo in devm_kfree comment
btrfs: free-space-cache.c: remove extra semicolon.
fat: Spelling s/obsolate/obsolete/g
SCSI, pmcraid: Fix spelling error in a pmcraid_err() call
tools/power turbostat: update fields in manpage
mac80211: drop spelling fix
types.h: fix comment spelling for 'architectures'
typo fixes: aera -> area, exntension -> extension
devices.txt: Fix typo of 'VMware'.
sis900: Fix enum typo 'sis900_rx_bufer_status'
decompress_bunzip2: remove invalid vi modeline
treewide: Fix comment and string typo 'bufer'
hyper-v: Update MAINTAINERS
treewide: Fix typos in various parts of the kernel, and fix some comments.
clockevents: drop unknown Kconfig symbol GENERIC_CLOCKEVENTS_MIGR
gpio: Kconfig: drop unknown symbol 'CS5535_GPIO'
leds: Kconfig: Fix typo 'D2NET_V2'
sound: Kconfig: drop unknown symbol ARCH_CLPS7500
...
Fix up trivial conflicts in arch/powerpc/platforms/40x/Kconfig (some new
kconfig additions, close to removed commented-out old ones)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=9ugo
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Changes queued in gpio/next for the start of the 3.3 merge window
* tag 'gpio-for-linus-20120104' of git://git.secretlab.ca/git/linux-2.6:
gpio: Add decode of WM8994 GPIO configuration
gpio: Convert GPIO drivers to module_platform_driver
gpio: Fix typo in comment in Samsung driver
gpio: Explicitly index samsung_gpio_cfgs
gpio: Add Linus Walleij as gpio co-maintainer
of: Add device tree selftests
of: create of_phandle_args to simplify return of phandle parsing data
gpio/powerpc: Eliminate duplication of of_get_named_gpio_flags()
gpio/microblaze: Eliminate duplication of of_get_named_gpio_flags()
gpiolib: output basic details and consolidate gpio device drivers
pch_gpio: Change company name OKI SEMICONDUCTOR to LAPIS Semiconductor
pch_gpio: Support new device LAPIS Semiconductor ML7831 IOH
spi/pl022: make the chip deselect handling thread safe
spi/pl022: add support for pm_runtime autosuspend
spi/pl022: disable the PL022 block when unused
spi/pl022: move device disable to workqueue thread
spi/pl022: skip default configuration before suspending
spi/pl022: fix build warnings
spi/pl022: only enable RX interrupts when TX is complete
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (73 commits)
arm: fix up some samsung merge sysdev conversion problems
firmware: Fix an oops on reading fw_priv->fw in sysfs loading file
Drivers:hv: Fix a bug in vmbus_driver_unregister()
driver core: remove __must_check from device_create_file
debugfs: add missing #ifdef HAS_IOMEM
arm: time.h: remove device.h #include
driver-core: remove sysdev.h usage.
clockevents: remove sysdev.h
arm: convert sysdev_class to a regular subsystem
arm: leds: convert sysdev_class to a regular subsystem
kobject: remove kset_find_obj_hinted()
m86k: gpio - convert sysdev_class to a regular subsystem
mips: txx9_sram - convert sysdev_class to a regular subsystem
mips: 7segled - convert sysdev_class to a regular subsystem
sh: dma - convert sysdev_class to a regular subsystem
sh: intc - convert sysdev_class to a regular subsystem
power: suspend - convert sysdev_class to a regular subsystem
power: qe_ic - convert sysdev_class to a regular subsystem
power: cmm - convert sysdev_class to a regular subsystem
s390: time - convert sysdev_class to a regular subsystem
...
Fix up conflicts with 'struct sysdev' removal from various platform
drivers that got changed:
- arch/arm/mach-exynos/cpu.c
- arch/arm/mach-exynos/irq-eint.c
- arch/arm/mach-s3c64xx/common.c
- arch/arm/mach-s3c64xx/cpu.c
- arch/arm/mach-s5p64x0/cpu.c
- arch/arm/mach-s5pv210/common.c
- arch/arm/plat-samsung/include/plat/cpu.h
- arch/powerpc/kernel/sysfs.c
and fix up cpu_is_hotpluggable() as per Greg in include/linux/cpu.h
* 'amba-modalias' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
sound: aaci: Enable module alias autogeneration for AMBA drivers
watchdog: sp805: Enable module alias autogeneration for AMBA drivers
fbdev: amba: Enable module alias autogeneration for AMBA drivers
serial: pl011: Enable module alias autogeneration for AMBA drivers
serial: pl010: Enable module alias autogeneration for AMBA drivers
spi: pl022: Enable module alias autogeneration for AMBA drivers
rtc: pl031: Enable module alias autogeneration for AMBA drivers
rtc: pl030: Enable module alias autogeneration for AMBA drivers
mmc: mmci: Enable module alias autogeneration for AMBA drivers
input: ambakmi: Enable module alias autogeneration for AMBA drivers
gpio: pl061: Enable module alias autogeneration for AMBA drivers
dmaengine: pl330: Enable module alias autogeneration for AMBA drivers
dmaengine: pl08x: Enable module alias autogeneration for AMBA drivers
hwrng: nomadik: Enable module alias autogeneration for AMBA drivers
ARM: amba: Auto-generate AMBA driver module aliases during modpost
ARM: amba: Move definition of struct amba_id to mod_devicetable.h
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drivers should not have a dependency on NR_IRQS. Doing so may break with
SPARSE_IRQ enabled. As there are no in kernel users of the pl061 which
have multiple instances with their interrupts combined to a single parent
interrupt, remove this functionality. If this capability is needed later,
it could be supported more cleanly by just using a devicetree property.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Convert the pl061 irq_chip code to use the generic irq chip code.
This has the side effect of using 32-bit accesses rather than 8-bit
accesses to interrupt registers. The h/w TRM and testing seem to indicate
this is fine.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds 2 functions that allow managed devices to request GPIOs.
These GPIOs will then be managed by drivers/base/devres.c.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We don't want drivers using NO_IRQ, so remove its use. For now, 0 or
-1 means no irq until platforms are converted to use 0.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.ml.walleij@gmail.com>
Use chained_irq_enter/exit helper functions instead of direct pointer
accesses. This is needed for generic irq chip conversion.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.ml.walleij@gmail.com>
This patch adds the suspend and resume operations in the driver. The patch
ensures the data save and restore for the device registers during the
suspend and resume operations respectively.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This driver will be converted to a dual GPIO + pinctrl driver
since it supports biasing and driving control options. Hopefully
it can serve as an example.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reimplement a call to devm_request_mem_region followed by a call to ioremap
or ioremap_nocache by a call to devm_request_and_ioremap.
The semantic patch that makes this transformation is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@nm@
expression myname;
identifier i;
@@
struct platform_driver i = { .driver = { .name = myname } };
@@
expression dev,res,size;
expression nm.myname;
@@
-if (!devm_request_mem_region(dev, res->start, size,
- \(res->name\|dev_name(dev)\|myname\))) {
- ...
- return ...;
-}
... when != res->start
(
-devm_ioremap(dev,res->start,size)
+devm_request_and_ioremap(dev,res)
|
-devm_ioremap_nocache(dev,res->start,size)
+devm_request_and_ioremap(dev,res)
)
... when any
when != res->start
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
For the human reader.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Where appropriate factor out some boilerplate code for platform device
registration into module_platform_driver. Drivers that don't use the
standard module_init initcall haven't been converted.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Make it easier to follow the by number references into samsung_gpio_cfgs
by putting the indexes into the code initialising the array, improving
readability a bit. Ideally we wouldn't be using magic array indexes at all
but this is easier than coming up with a better way.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
As gpio chips get registered, a device tree node which represents the
gpio chip is searched and attached to it. A translate function is also
provided to convert the gpio specifier into actual platform settings
for pin function selection, pull up/down and driver strength settings.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
[kgene.kim@samsung.com: fixed build error]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The sysdev.h file should not be needed by any in-kernel code, so remove
the .h file from these random files that seem to still want to include
it.
The sysdev code will be going away soon, so this include needs to be
removed no matter what.
Cc: Jiandong Zheng <jdzheng@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: "Venkatesh Pallipadi
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
This patch is functionally tested on Samsung SMDKV6410.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
[grant.likely: don't create an unnecessary header file]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add a 5121-custom reject if an input-only pin is requested to be output
(see 18.3.1.1 in the refman). Also, rewrite mach-specific quirk setup to
consume less lines which scales better.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
[grant.likely: Fixed build error]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
These hooks will be needed by the general disabl/enable_irq();
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
GPIO's irq action's dev_id is set to the first struct ioh_gpio chip,
so when loop checking the 8 chips, the "chip" should be changed
according.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In adding DT binding support, the check for NULL platform_data got added
back in inadvertently, so remove it.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
A large chunk of qe_pin_request() is unnecessarily cut-and-paste
directly from of_get_named_gpio_flags(). This patch cuts out the
duplicate code and replaces it with a call to of_get_gpio().
v2: fixed compile error due to missing gpio_to_chip()
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
This patch adds a kernel message, containing GPIO range and device
name on successful device registration, and removes duplicate messages from the following drivers:
* gpio-adp5588
* gpio-bt8xx
* gpio-cs5535
* gpio-janz-ttl
* gpio-nomadik
* gpio-pcf857x
* gpio-xilinx
* drivers/of/gpio.c
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
[grant.likely@secretlab.ca: squashed 2 patches together]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
On October 1 in 2011,
OKI SEMICONDUCTOR Co., Ltd. changed the company name in to LAPIS Semiconductor Co., Ltd.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
ML7831 is companion chip for Intel Atom E6xx series.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
I screwed up by compiling that driver for the machine rather
than the arch. Correcting this fixes the build error.
Cc: Grant Likely <grant.likely@secretlab.ca>
Reported-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit af0c25c487 ("staging: remove obsoleted CS5535/CS5536 GPIO
driver") dropped CS5535_GPIO. So this last reference to CS5535_GPIO has
been an (inconsequential) nop since v3.1. Drop it too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It's not used outside of the driver so doesn't need to be exported, and
sparse notices this and complains about it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'gpio/merge' of git://git.secretlab.ca/git/linux-2.6:
gpio: pca953x: propagate the errno from the chip_init functions
gpio: pca953x: remove unneeded check for chip type
gpio/omap: check return value from irq_alloc_generic_chip
gpio/omap: replace MOD_REG_BIT macro with static inline
Support clk in gpio driver. There's no gpio clock in PXA25x and PXA27x.
So use dummy clk instead. And move the gpio edge initialization into
gpio driver for arch-mmp.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Use cpuid to recognize the gpio number and type. CPU_PXA26x is the
special case since we can't identify it by cpuid.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Avoid to define gpio_to_irq() and irq_to_gpio() for potential name
confliction since multiple architecture will be built together.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
GPIO0 and GPIO1 are linked to unique interrupt line in PXA series,
others are linked to another interrupt line. All GPIO are linked to one
interrupt line in MMP series.
Since gpio driver is shared between PXA series and MMP series, define
GPIO0 and GPIO1 as chained interrupt chip. So we can move out gpio code
from irq.c to gpio-pxa.c.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (106 commits)
powerpc/p3060qds: Add support for P3060QDS board
powerpc/83xx: Add shutdown request support to MCU handling on MPC8349 MITX
powerpc/85xx: Make kexec to interate over online cpus
powerpc/fsl_booke: Fix comment in head_fsl_booke.S
powerpc/85xx: issue 15 EOI after core reset for FSL CoreNet devices
powerpc/8xxx: Fix interrupt handling in MPC8xxx GPIO driver
powerpc/85xx: Add 'fsl,pq3-gpio' compatiable for GPIO driver
powerpc/86xx: Correct Gianfar support for GE boards
powerpc/cpm: Clear muram before it is in use.
drivers/virt: add ioctl for 32-bit compat on 64-bit to fsl-hv-manager
powerpc/fsl_msi: add support for "msi-address-64" property
powerpc/85xx: Setup secondary cores PIR with hard SMP id
powerpc/fsl-booke: Fix settlbcam for 64-bit
powerpc/85xx: Adding DCSR node to dtsi device trees
powerpc/85xx: clean up FPGA device tree nodes for Freecsale QorIQ boards
powerpc/85xx: fix PHYS_64BIT selection for P1022DS
powerpc/fsl-booke: Fix setup_initial_memory_limit to not blindly map
powerpc: respect mem= setting for early memory limit setup
powerpc: Update corenet64_smp_defconfig
powerpc: Update mpc85xx/corenet 32-bit defconfigs
...
Fix up trivial conflicts in:
- arch/powerpc/configs/40x/hcu4_defconfig
removed stale file, edited elsewhere
- arch/powerpc/include/asm/udbg.h, arch/powerpc/kernel/udbg.c:
added opal and gelic drivers vs added ePAPR driver
- drivers/tty/serial/8250.c
moved UPIO_TSI to powerpc vs removed UPIO_DWAPB support
* 'next/devel2' of git://git.linaro.org/people/arnd/arm-soc: (30 commits)
ARM: mmp: register internal sram bank
ARM: mmp: register audio sram bank
ARM: mmp: add sram allocator
gpio/samsung: Complain loudly if we don't know the SoC
ARM: S3C64XX: Fix SoC identification for S3C64xx devices
ARM: S3C2443: Remove redundant s3c_register_clocks call for init_clocks
ARM: S3C24XX: Add devname for hsmmc1 pclk
ARM: S3C24XX: use clk_get_rate to init fclk in common_setup_clocks
ARM: S3C2443: Accommodate cpufreq frequency scheme in armdiv
ARM: S3C2443: handle unset armdiv values gracefully
ARM: S3C2443: Add get_rate operation for clk_armdiv
ARM: S3C2416: Add comment describing the armdiv/armclk
ARM: S3C2443: Move clk_arm and clk_armdiv to common code
ARM: S3C24XX: Add infrastructure to transmit armdiv to common code
ARM: S3C2416: Add armdiv_mask constant
ARM: EXYNOS4: Add support for M-5MOLS camera on Nuri board
ARM: EXYNOS4: Enable MFC on ORIGEN
ARM: SAMSUNG: Add support s3c2416-adc for S3C2416/S3C2450
ARM: SAMSUNG: Add support s3c2443-adc for S3C2443
ARM: SAMSUNG: Allow overriding of adc device name for S3C24XX
...
* 'next/cleanup3' of git://git.linaro.org/people/arnd/arm-soc: (79 commits)
ARM: SAMSUNG: Move fimc plat. device from board files to plat-samsung
ARM: SAMSUNG: Cleanup resources by using macro
ARM: SAMSUNG: Cleanup plat-samsung/devs.c and devs.h
ARM: S5P: To merge devs.c files to one devs.c
ARM: S3C64XX: To merge devs.c files to one devs.c
ARM: S3C24XX: To merge s3c24xx devs.c files to one devs.c
ARM: S5P64X0: Add Power Management support
ARM: S5P: Make the sleep code common for S5P series SoCs
ARM: S5P: Make the common S5P PM code conditionally compile
ARM: SAMSUNG: Move S5P header files to plat-samsung
ARM: SAMSUNG: Move S3C24XX header files to plat-samsung
ARM: SAMSUNG: Moving each SoC support header files
ARM: SAMSUNG: Consolidate plat/pll.h
ARM: SAMSUNG: Consolidate plat/pwm-clock.h
ARM: SAMSUNG: Cleanup mach/clkdev.h
ARM: SAMSUNG: remove sdhci default configuration setup platform helper
ARM: EXYNOS4: Add FIMC device on SMDKV310 board
ARM: EXYNOS4: Add header file protection macros
ARM: EXYNOS4: Add usb ehci device to the SMDKV310
ARM: S3C2443: Add hsspi-clock from pclk and rename S3C2443 hsspi sclk
...
Fix up conflicts in
- arch/arm/mach-exynos4/{Kconfig,clock.c}
ARM_CPU_SUSPEND, various random device tables (gah!)
- drivers/gpio/Makefile
sa1100 gpio added, samsung gpio drivers merged
Interrupt handler in MPC8xxx GPIO driver is missing the call to PIC EOI
(end of interrupt) handler. As a result, at least on 85XX systems, GPIO
interrupt is delivered only once. This patch adds the missing EOI call.
Tested on custom P1022 board.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support MPC85xx platforms outside of MPC8572/MPC8536. The
MPC8572/MPC8536 have an erratum that is worked around based on having
"fsl,mpc8572-gpio" in the compatiable list. All other MPC85xx SoCs
don't require this workaround and thus utilize the 'fsl,pq3-gpio'
compatiable.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'for-next' of git://git.infradead.org/users/sameo/mfd-2.6: (80 commits)
mfd: Fix missing abx500 header file updates
mfd: Add missing <linux/io.h> include to intel_msic
x86, mrst: add platform support for MSIC MFD driver
mfd: Expose TurnOnStatus in ab8500 sysfs
mfd: Remove support for early drop ab8500 chip
mfd: Add support for ab8500 v3.3
mfd: Add ab8500 interrupt disable hook
mfd: Convert db8500-prcmu panic() into pr_crit()
mfd: Refactor db8500-prcmu request_clock() function
mfd: Rename db8500-prcmu init function
mfd: Fix db5500-prcmu defines
mfd: db8500-prcmu voltage domain consumers additions
mfd: db8500-prcmu reset code retrieval
mfd: db8500-prcmu tweak for modem wakeup
mfd: Add db8500-pcmu watchdog accessor functions for watchdog
mfd: hwacc power state db8500-prcmu accessor
mfd: Add db8500-prcmu accessors for PLL and SGA clock
mfd: Move to the new db500 PRCMU API
mfd: Create a common interface for dbx500 PRCMU drivers
mfd: Initialize DB8500 PRCMU regs
...
Fix up trivial conflicts in
arch/arm/mach-imx/mach-mx31moboard.c
arch/arm/mach-omap2/board-omap3beagle.c
arch/arm/mach-u300/include/mach/irqs.h
drivers/mfd/wm831x-spi.c
* 'next/devel' of git://git.linaro.org/people/arnd/arm-soc: (50 commits)
ARM: tegra: update defconfig
arm/tegra: Harmony: Configure PMC for low-level interrupts
arm/tegra: device tree support for ventana board
arm/tegra: add support for ventana pinmuxing
arm/tegra: prepare Seaboard pinmux code for derived boards
arm/tegra: pinmux: ioremap registers
gpio/tegra: Convert to a platform device
arm/tegra: Convert pinmux driver to a platform device
arm/dt: Tegra: Add pinmux node to tegra20.dtsi
arm/tegra: Prep boards for gpio/pinmux conversion to pdevs
ARM: mx5: fix clock usage for suspend
ARM i.MX entry-macro.S: remove now unused code
ARM i.MX boards: use CONFIG_MULTI_IRQ_HANDLER
ARM i.MX tzic: add handle_irq function
ARM i.MX avic: add handle_irq function
ARM: mx25: Add the missing IIM base definition
ARM i.MX avic: convert to use generic irq chip
mx31moboard: Add poweroff support
ARM: mach-qong: Add watchdog support
ARM: davinci: AM18x: Add wl1271/wlan support
...
Fix up conflicts in:
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-mx5/devices-imx53.h
arch/arm/plat-mxc/include/mach/memory.h
* 'next/fixes' of git://git.linaro.org/people/arnd/arm-soc: (28 commits)
ARM: pxa/cm-x300: properly set bt_reset pin
ARM: mmp: rename SHEEVAD to GPLUGD
ARM: imx: Fix typo 'MACH_MX31_3DS_MXC_NAND_USE_BBT'
ARM: i.MX28: shift frac value in _CLK_SET_RATE
plat-mxc: iomux-v3.h: implicitly enable pull-up/down when that's desired
ARM: mx5: fix clock usage for suspend
ARM: pxa: use correct __iomem annotations
ARM: pxa: sharpsl pm needs SPI
ARM: pxa: centro and treo680 need palm27x
ARM: pxa: make pxafb_smart_*() empty when not enabled
ARM: pxa: select POWER_SUPPLY on raumfeld
ARM: pxa: pxa95x is incompatible with earlier pxa
ARM: pxa: CPU_FREQ_TABLE is needed for CPU_FREQ
ARM: pxa: pxa95x/saarb depends on pxa3xx code
ARM: pxa: allow selecting just one of TREO680/CENTRO
ARM: pxa: export symbols from pxa3xx-ulpi
ARM: pxa: make zylonite_pxa*_init declaration match code
ARM: pxa/z2: fix building error of pxa27x_cpu_suspend() no longer available
ARM: at91: add defconfig for at91sam9g45 family
ARM: at91: remove dependency for Atmel PWM driver selector in Kconfig
...
A pending cleanup will mean that module.h won't be implicitly
everywhere anymore. Make sure the modular drivers in gpio
are actually calling out for <module.h> explicitly in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6:
h8300: Move gpio.h to gpio-internal.h
gpio: pl061: add DT binding support
gpio: fix build error in include/asm-generic/gpio.h
gpiolib: Ensure struct gpio is always defined
irq: Add EXPORT_SYMBOL_GPL to function of irq generic-chip
gpio-ml-ioh: Use NUMA_NO_NODE not GFP_KERNEL
gpio-pch: Use NUMA_NO_NODE not GFP_KERNEL
gpio: langwell: ensure alternate function is cleared
gpio-pch: Support interrupt function
gpio-pch: Save register value in suspend()
gpio-pch: modify gpio_nums and mask
gpio-pch: support ML7223 IOH n-Bus
gpio-pch: add spinlock in suspend/resume processing
gpio-pch: Delete invalid "restore" code in suspend()
gpio-ml-ioh: Fix suspend/resume issue
gpio-ml-ioh: Support interrupt function
gpio-ml-ioh: Delete unnecessary code
gpio/mxc: add chained_irq_enter/exit() to mx3_gpio_irq_handler()
gpio/nomadik: use genirq core to track enablement
gpio/nomadik: disable clocks when unused
Initializing the chips may return with an error, but this error gets
dropped in probe(). Propagate this further to the driver core. Also,
simplify returning the error in one of the init functions.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We can assume our own device_id table is correct, so remove checking if
the chip type is valid. (The check was bogus anyway: If it found an
invalid entry, it returned with 0!) This is in preparation for further
cleanups.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This adds devicetree binding support to the ARM pl061 driver removing the
platform_data dependency. When DT binding is used, the gpio numbering is
assigned dynamically. For now, interrupts are not supported with DT until
irqdomains learn dynamic irq assignment.
Rather than add another case of -1, updating the driver to use NO_IRQ.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We currently have two symbols to control compilation the MFD subsystem,
MFD_SUPPORT and MFD_CORE. The MFD_SUPPORT is actually not required
at all, it only hides the submenu when not set, with the effect that
Kconfig warns about missing dependencies when another driver selects
an MFD driver while MFD_SUPPORT is disabled. Turning the MFD submenu
back from menuconfig into a plain menu simplifies the Kconfig syntax
for those kinds of users and avoids the surprise when the menu
suddenly appears because another driver was enabled that selects this
symbol.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently, GFP_KERNEL is used as parameter of irq_alloc_descs like below.
irq_base = irq_alloc_descs(-1, IOH_IRQ_BASE, num_ports[j],
GFP_KERNEL);
This is not true.
So, this patch uses NUMA_NO_NODE not GFP_KERNEL.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: David Rientjes <rientjes@google.com>
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently, GFP_KERNEL is used as parameter of irq_alloc_descs like below.
irq_base = irq_alloc_descs(-1, IOH_IRQ_BASE, num_ports[j],
GFP_KERNEL);
This is not true.
So, this patch uses NUMA_NO_NODE not GFP_KERNEL.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: David Rientjes <rientjes@google.com>
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
If we don't know the SoC type then we won't add any chips which is rather
unfortunate as neither GPIO nor pinmux APIs will work, breaking lots of
different subsystems. Logging at least provides a hint to the user as to
what's gone wrong.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
v3: Make regs variable static. Remove empty init of tegra_gpio_banks.
v2: Retrieve IRQ and memory addresses from resources instead of hard-
coding them. Add back initialization of tegra_gpio_chip.of_node.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
[olof: switched probe routine to __devinit]
Signed-off-by: Olof Johansson <olof@lixom.net>
gpio_base was set to 0 if no system platform data or open firmware
platform data was provided. This led to conflicts, if any other gpiochip
with a gpiobase of 0 was instantiated already. Setting it to -1 will
automatically use the first one available.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
With commit f64ad1a0e2, "gpio/omap: cleanup _set_gpio_wakeup(), remove
ifdefs", access to build time conditionally omitted 'suspend_wakeup'
member of the 'gpio_bank' structure has been placed unconditionally in
function _set_gpio_wakeup(), which is always built. This resulted in the
driver compilation broken for certain OMAP1, i.e., non-OMAP16xx,
configurations.
Really required or not in previously excluded cases, define this
structure member unconditionally as a fix.
Tested with a custom OMAP1510 only configuration.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Kevin Hilman <khilman@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In drivers/gpio/gpio-samsung.c, there are certain structures
and functions which are not getting used if the particular
CPU is not selected. These code segments are moved under CPU
specific macros to remove compilation warnings.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Some of the gpio chips of exynos4 are assigned a default gpio config without
the exynos4 specific pull up/down callbacks which resulted in incorrect
setting of pull up/down configuration.
Fix this by adding two new exynos4 specific entries in the array of default
configs with set_pull and get_pull callbacks set to exynos4 specific callbacks
The new default gpio configs can then be used for exynos4 gpio chips.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Only register gpio banks provided by SoC instead of the maximum possible
to lessen confusion, get rid of a warning from gpiolib and stop it from
eating into the extra gpios for configs with S3C24XX_GPIO_EXTRA != 0.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Alternate function must be zero for the pin to act as
a GPIO.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently, when suspend is occurred, register im0/1 and gpio_use_sel are not
saved.
This patch modifies so that register im0/1 and gpio_use_sel are saved.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently, the number of GPIO pins is set fixed value(=12).
Also PIN MASK is set as '0xfff'.
However the pins differs by IOH.
This patch sets the value correctly.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently, some registers are not saved in case changing to suspend state.
This patch fixes the issue.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This register restore processing is unnecessary in suspend processing.
(The restore processing is already in resume processing)
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Commit 1b39d5f2cc introduced new common gpio driver for all Samsung GPIO
SoCs. The new driver use wrong configuration setup for all gpio pins on
S5PC100 and S5PV210 SoCs and external interrupt lines on Exynos4 SoCs.
This patch fixes this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Commit 1b39d5f2cc introduced new common gpio driver for all Samsung GPIO
SoCs. The new driver doesn't correctly register GPIO interrupts on
Samsung Exynos4 SoCs. This is caused by a typo in define name. This
patch fixes this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Commit 1b39d5f2cc introduced new common gpio driver for all Samsung GPIO
SoCs. The new driver doesn't work correctly on Samsung Exynos4 SoC. It
fails to set configuration for all but external interrupt pins. This
patch fixes this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The <mach/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per example from the other ARM boards, push the PXA
GPIO driver down to the GPIO subsystem so it can be consolidated.
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The <mach/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Cc: Ryan Mallon <rmallon@gmail.com>
Acked-by: Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This will eventually allow <mach/gpio.h> to be deleted. This mirrors
LinusW's recent equivalent work on various other ARM platforms.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the driver to the place where it is expected to be nowadays. Also
rename its CONFIG-name to match the rest and adapt the defconfigs.
Finally, move selection of REQUIRE_GPIOLIB or WANTS_OPTIONAL_GPIOLIB to
the platforms, because this option is per-platform and not per-driver.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The mx3_gpio_irq_handler() is also called on imx6q which has GIC as
the primary interrupt controller. As GIC implements the fasteoi flow
control, we need to add chained_irq_enter/exit() to
mx3_gpio_irq_handler() for signaling EOI, otherwise system will hang
whenever there is a gpio irq triggered.
v2: use chained_irq_{enter,exit}()
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds support for Samsung GPIOs with one gpio driver
and removes old GPIO drivers which are drivers/gpio-s3c24xx.c,
gpio-s3c64xx.c, gpio-s5p64x0.c, gpio-s5pc100.c, gpio-s5pv210.c,
gpio-exynos4.c, gpio-plat-samsung.c, plat-samsung/gpio-config.c
and gpio.c to support each Samsung SoCs before. Because the
gpio-samsung.c can replace old Samsung GPIO drivers.
Basically, the gpio-samsung.c has been made by their merging
and removing duplicated definitions.
Note: gpio-samsung.c includes some SoC dependent codes and it
will be replaced next time.
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
[kgene.kim@samsung.com: squash the removing and adding patches]
[kgene.kim@samsung.com: fixes bug during to register of gpio_chips]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Currently the Nomadik GPIO driver tracks enabled/disabled interrupt
status with a local variable, switch to using the interrupt core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The GPIO clock is required for register access and interrupt detection.
When interrupt detection is not required on any of the pin in a block,
the block's clock can be disabled when the registers are not being
accessed.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
[Adjust for new IRQ chip core code, use only local functions]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Building a kernel with hotplug disabled results in a link failure:
`bgpio_remove' referenced in section `___ksymtab_gpl+bgpio_remove' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
This is because of bgpio_remove() is exported. It is illegal to export
symbols which are discarded either at link time or as part of an
init/exit section.
Fix this by dropping the __devexit attributation from bgpio_remove().
Also drop the __devinit attributation from bgpio_init().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This rewrites the U300 GPIO so as to use gpiolib and
struct gpio_chip instead of just generic GPIO, hiding
all the platform specifics and passing in GPIO chip
variant as platform data at runtime instead of the
compiletime kludges.
As a result <mach/gpio.h> is now empty for U300 and
using just defaults.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Debian kernel maintainers <debian-kernel@lists.debian.org>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since commit 5093aec872
"arm: davinci: Cleanup irq chip code", the variable 'mask' and 'g'
are not being used.
This patch eliminate below unused variable warnings:
CC drivers/gpio/gpio-davinci.o
drivers/gpio/gpio-davinci.c: In function 'gpio_irq_type':
drivers/gpio/gpio-davinci.c:234: warning: unused variable 'mask'
drivers/gpio/gpio-davinci.c:233: warning: unused variable 'g'
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
irq_to_gpio is being removed. Replace the only use of that API by
the ARM Tegra sub-architecture.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure return value of irq_alloc_generic_chip() is checked before continuing
on to use it.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This macro is ugly and confusing, especially since it passes in most
arguments, but uses an implied 'base' from the caller.
Replace it with an equivalent static inline.
Signed-off-by: Kevin Hilman <khilman@ti.com>
As per example from the other ARM boards, push the SA100
GPIO driver down to the GPIO subsystem so it can be consolidated.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The <mach/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Barry Song <bs14@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per example from the other ARM boards, push the LPC32XX
GPIO driver down to the GPIO subsystem so it can be consolidated.
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Barry Song <bs14@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the ep93xx machine specific dependencies for gpio_to_irq() by
hooking up the callback in the driver and using __gpio_to_irq.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per example from the other ARM boards, push the DaVinci TNET
GPIO driver down to the GPIO subsystem so it can be consolidated.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per example from the other ARM boards, push the DaVinci GPIO
driver down to the GPIO subsystem so it can be consolidated.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The <mach/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Cc: zeal <zealcook@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: Daniel Silverstone <dsilvers@simtec.co.uk>
Acked-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per example from the other ARM boards, push the KS8695 GPIO
driver down to the GPIO subsystem so it can be consolidated.
Cc: zeal <zealcook@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: Daniel Silverstone <dsilvers@simtec.co.uk>
Acked-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The <mach/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The <[plat|mach]/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As irq_to_gpio() is only being used by gpio-mxs driver, it should be
moved from mach/gpio.h into gpio-mxs.c.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As irq_to_gpio() is only being used by gpio-mxc driver, it should be
moved from mach/gpio.h into gpio-mxc.c.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It adds .to_irq support for gpio chip, so that __gpio_to_irq in
gpiolib becomes usable.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Migrate the driver for the v7-based MSM chips into drivers/gpio. The
driver is unchanged, only moved.
Change-Id: I810db5b50b71cdca4e869aa0d0310f7f48781a55
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Migrate the driver for the v6-based MSM chips into drivers/gpio. The
driver is unchanged, only moved.
Change-Id: I03ba597b95b4d62b42da112a8efac88d67aa40f9
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
TPS65912 has five GPIOs that can be configured for different
purposes.
Signed-off-by: Margarita Olaya Cabrera <magi@slimlogic.co.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since 43cc71eed1 (platform: prefix MODALIAS
with "platform:"), the platform modalias is prefixed with "platform:".
This patch changes the MODULE_ALIAS to "platform:ab8500-gpio".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6: (61 commits)
gpio/mxc/mxs: fix build error introduced by the irq_gc_ack() renaming
mcp23s08: add i2c support
mcp23s08: isolate spi specific parts
mcp23s08: get rid of setup/teardown callbacks
gpio/tegra: dt: add binding for gpio polarity
mcp23s08: remove unused work queue
gpio/da9052: remove a redundant assignment for gpio->da9052
gpio/mxc: add device tree probe support
ARM: mxc: use ARCH_NR_GPIOS to define gpio number
gpio/mxc: get rid of the uses of cpu_is_mx()
gpio/mxc: add missing initialization of basic_mmio_gpio shadow variables
gpio: Move mpc5200 gpio driver to drivers/gpio
GPIO: DA9052 GPIO module v3
gpio/tegra: Use engineering names in DT compatible property
of/gpio: Add new method for getting gpios under different property names
gpio/dt: Refine GPIO device tree binding
gpio/ml-ioh: fix off-by-one for displaying variable i in dev_err
gpio/pca953x: Deprecate meaningless device-tree bindings
gpio/pca953x: Remove dynamic platform data pointer
gpio/pca953x: Fix IRQ support.
...
The following commit renames irq_gc_ack() to irq_gc_ack_set_bit(),
and makes gpio-mxc and gpio-mxs fail to build.
659fb32d1b
genirq: replace irq_gc_ack() with {set,clr}_bit variants (fwd)
The patch fixed a couple of typo of comma to semicolon.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add i2c bindings for the mcp230xx devices. This is quite a lot simpler
than the spi one as there's no funky sub addressing done (one struct
i2c_client per struct gpio_chip).
The mcp23s08_platform_data structure is reused for i2c, even though
only a single mcp23s08_chip_info structure is needed.
To use, simply fill out a platform_data structure and pass it in
i2c_board_info, E.G.:
static const struct mcp23s08_platform_data mcp23017_data = {
.chip[0] = {
.pullups = 0x00ff,
},
.base = 240,
};
static struct i2c_board_info __initdata i2c_devs[] = {
{ I2C_BOARD_INFO("mcp23017", 0x20),
.platform_data = &smartview_mcp23017_data, },
...
};
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Change spi member of struct mcp23s08 to be a ops-specific opaque data
pointer, and move spi specific knowledge out of mcp23s08_probe_one().
No functional change, but is needed to add i2c support.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
There's no in-tree users, and bus notifiers are more generic anyway.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The patch adds device tree probe support for gpio-mxc driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The patch removes all the uses of cpu_is_mx(). Instead, it utilizes
platform_device_id to distinguish the different gpio types, IMX1_GPIO
on i.mx1, IMX21_GPIO on i.mx21 and i.mx27, IMX31_GPIO on all other
i.mx SoCs.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The wrong bit was masked when acking langwell gpio interrupts.
Reason for maskig the wrong bit was probably because__ffs() and ffs() functions
return bit indexes differently (0..31 vs 1..32)
This fixes langwell based devices from hanging when a gpio interrupt is
triggered and undoes the breakage which occurred in change set
732063b92b
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The bgpio_init() function does not initialise the shadow register for
the GPIO direction register. Thus, when configuring the first GPIO with
gpio_set_direction() all other GPIOs of the same bank will be
configured as inputs. Since the bgpio layer cannot know whether the
register is readable, the initialisation should be done by the caller
of bgpio_init().
Also, the 'data' shadow variable that is used inside basic_mmio_gpio
to cache the current value of the GPIO_DR register is initialised from
the GPIO_PSR register within bgpio_init(). Thus when setting the
output value of a certain GPIO, the other GPIO outputs of the same
bank will be set or cleared depending on the pin state of the GPIO
inputs during bgpio_init().
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
GPIO drivers are getting consolidated into drivers/gpio. While at it,
change the driver name to mpc5200-gpio* to avoid collisions.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
DA9052 PMIC has 16 bit GPIO bus for peripheral control.
This patch add support for the GPIO pins on the DA9052.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Engineering names are more stable than marketing names. Hence, use them
for Device Tree compatible properties instead.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Many stupid corrections of duplicated includes based on the output of
scripts/checkincludes.pl.
Signed-off-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
with the "for (; i != 0; i--)" sytax, i-- will be executed after the iteration.
thus dev_err shows wrong i value.
Switch to "while(--i >= 0)" which is better in readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The property 'polarity' is handled by the GPIO core, and the 'gpio-base'
should be assigned automatically. It is meaningless in the device-tree,
since GPIO's are identified by the "chip-name"/offset pair.
This way, the whole pca953x_get_alt_pdata() can hopefully soon go away.
We still need to check whether we really want GPIO-interrupt functionality
by simply looking if the I2C node has an interrupts property defined, since
this property is not used for anything else.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In the case that we obtain device-tree data to fill in platform_data, the new
platform data struct was dynamically allocated, but the pointer to it was not
used everywhere it should. It seems easier to fix this issue by removing the
dynamic allocation altogether since its data is only used during driver
probing.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It seems that in the normal case, IRQ_NOREQUEST needs to be explicitly
cleared, otherwise claiming the interrupt fails.
In the case of sparse interrupts, the descriptor needs to be allocated
first.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Remove cpu_is_* checks from gpio_show_revision() by passing in the
revision address offset from platform data. SoCs with no revision
register (15xx, 7xx, and all MPUIOs) use -1 (actually, USHRT_MAX) to
signify no register.
While here, all GPIO banks are assumed to be the same revision, so fix
show_revision() to only show the revision for the first bank it finds.
This removes duplicate GPIO revision prints during boot.
Thanks to Charulatha V <charu@ti.com> for finding/fixing a few -1s
that were missed in the original patch.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Make _set_gpio_wakeup() generic by removing ifdefs. Code for the
various SoCs/bank-methods was already the same, except for the
non-wakeup GPIO checking. But that flag is set on a per-SoC basis, so
can be used for all SoCs.
While here, use dev_err() and remove GPIO bank calculation assumption
based on subtracting bank pointers.
Signed-off-by: Kevin Hilman <khilman@ti.com>
These functions are useless. They are only called in a few places,
and where they are called, the GPIO has already been converted from an
IRQ or masked, so these functions will never fail.
Signed-off-by: Kevin Hilman <khilman@ti.com>
MPUIO banks have their own dedicated IRQ chip interface, separate from
the "normal" GPIO banks. Convert the MPUIO IRQ chip over to using
the new generic IRQ chip interface.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cleanup GPIO IRQ enable/disable handling by removing SoC-specific
Also split enable/disable IRQ into separate functions for better
readability and also facilitate potentially moving to generic irq_chip
in the future.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cleanup IRQ status handling by passing IRQ status register offsets
via platform data.
Cleans up clearing of GPIO IRQ status and GPIO ISR handler.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add register offset fields to GPIO platform_data for registers.
This patch adds registers that control direction, input and output
data. Using these register offsets in the common driver allows
removal of #ifdefs and greatly improves readability.
Also create dedicated data out functions: one for banks with dedicated
set/clear registers, and another for banks with a single mask
register.
Signed-off-by: Kevin Hilman <khilman@ti.com>
The get_gpio_index() function, littered with cpu_is_* checks can be easily
replaced by using bitops based on the GPIO bank width. Do so.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Rather than having a file-global bank_width variable, move it into
struct gpio_bank so it can be bank-specific. Note the bank width
is already passed per-bank via platform_data, so current code would
be incorrect if any banks had different width.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove the OMAP1 #ifdef and MPUIO special case for _clear_gpio_irqbank()
The MPUIOs do not need a register access to ack/clear the IRQ status,
since reading the IRQ status clears it. In addition, the MPUIO
irq_chip has an empty ack method, so _clear_gpio_irqbank() is never
used for MPUIOs.
Signed-off-by: Kevin Hilman <khilman@ti.com>
In commit 78a1a6d341 (ARM: OMAP4: Update
the GPIO support) braces were mistakenly added to included the
register read-back inside the cpu_is_* checking.
Remove the braces, ensuring that a register read-back is done, even
when the IRQSTATUS2 register is not written.
Note that the register read-back might be IRQSTATUS1 or IRQSTATUS2
depending on the CPU, but a read-back of any register in that region
will cause a flush of the posted writes.
Signed-off-by: Kevin Hilman <khilman@ti.com>
If gpio pins from bank[2-5] are marked as wakeup enable and if the wake is
through gpio IO pad wakeup, then that wakeup gpio interrupt is lost.
In the current implementation, GPIO driver stores the context of DATAIN of
all the gpio in the bank. During GPIO resuming, it checks DATAIN with wakeup
enabled pins of gpio bank. If there is status change, then manually toggle
GPIO_LEVELDETECT to generate pseudo interrupt.
Reported-by: Philippe Mazet <p-mazet@ti.com>
Tested-by: Philippe Mazet <p-mazet@ti.com>
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
As part of the gpio driver consolidation, this patch moves the Tegra driver
into drivers/gpio
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
The 74x164 GPIO driver has a static inline helper called
gpio_to_chip which clashes with the gpiolib namespace if we
try to expose the function with the same name from gpiolib,
and it's still confusing even if we don't do that. So rename
it to gpio_to_74x164_chip().
Reported-by: H Hartley Sweeten <hartleys@visionengravers.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When calling gpio_get_value, the gpio number other than bit offset
should be passed as the argument.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Remove miscellaneous use of direct calculation by using resource_size().
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The mach-nomadik machine did not compile properly due to bad
ux500-specific functions being called. Introduce new state
variables to fix this up.
Reported-by: Axel Lin <axel.lin@gmail.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Prafulla Wadaskar <prafulla.wadaskar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This converts the gpio-ep93xx driver into a platform_driver and uses
the basic_mmio_gpio library.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When using nested threaded irqs, use handle_nested_irq(). This function
does not call the chip handler, so no handler is set.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The interrupt pin of the PCA953x is active low, and on the rising edge
no interrupt should be produced.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It seems that in the normal case, IRQ_NOREQUEST needs to be explicitly
cleared, otherwise claiming the interrupt fails.
In the case of sparse interrupts, the descriptor needs to be allocated
first.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
With this driver now being moved from arch/arm/mach-ep93xx/gpio.c to
drivers/gpio/gpio-ep93xx.c the prefix "ep93xx" is now redundant in the
pr_* output. Using KBUILD_MODNAME is sufficient.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The Samsung GPIO drivers are always built-in when the relevant
platform is selected. Change the Kconfig symbol to def_bool y
dependant on the platform.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The S3C_GPIO_PULL_UP macro value incorrectly maps to a reserved setting of GPIO
pull up/down registers on Exynos4 platform. Fix this incorrect mapping by adding
wrappers to the s3c_gpio_setpull_updown and s3c_gpio_getpull_updown functions.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The patch converts gpio-mxs driver to use generic irq chip.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The irq_high stuff was mistakenly copied from mxc gpio driver.
The mxs gpio controller has only one irq line for each 32-pin
gpio port. The patch remove irq_high related codes.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The gpio-mxs controller complies with basic_mmio_gpio library. This
patch converts the driver to use the library.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
_set_gpio_triggering uses read-modify-write on bank registers,
lock bank->lock around all calls to it to prevent register
corruption if two cpus access gpios in the same bank at the
same time.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Setting the IRQWAKEN bit was overwriting previous IRQWAKEN bits,
causing only the last bit set to take effect, resulting in lost
wakeups when the GPIO controller is in idle.
Replace direct writes to IRQWAKEN with MOD_REG_BIT calls to
perform a read-modify-write on the register.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
WARNING: arch/arm/plat-omap/built-in.o(.devinit.text+0x46c): Section mismatch in reference from the function omap_gpio_probe() to the function .init.text:omap_gpio_chip_init()
The function __devinit omap_gpio_probe() references
a function __init omap_gpio_chip_init().
If omap_gpio_chip_init is only used by omap_gpio_probe then
annotate omap_gpio_chip_init with a matching annotation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Sort the gpio makefile and enforce the naming convention gpio-*.c for
gpio drivers.
v2: cleaned up filenames in Kconfig and comment blocks
v3: fixup use of BASIC_MMIO to GENERIC_GPIO for mxc
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The interrupt pin of the PCA953x is active low, and on the rising edge
no interrupt should be produced.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The GPIO driver should reside in drivers/gpio.
v3: Change Kconfig option to def_bool y
v2: Make the Kconfig symbol a silent option, dependent on ARCH_EP93XX
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The gpio-mxc controller complies with basic_mmio_gpio library. The
patch convert the driver to use the library.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The patch makes necessary changes on gpio-mxc as below to turn it
into an upstanding gpio driver.
* Add a list to save all mx2 ports references, so that
mx2_gpio_irq_handler can walk through all interrupt status
registers
* Use readl/writel to replace mach-specific accessors
__raw_readl/__raw_writel
* Change mxc_gpio_init into mxc_gpio_probe function
* Move "struct mxc_gpio_port" into gpio-mxc.c, as it needs not to
be public at all, and also make some other cleanup on
plat-mxc/include/mach/gpio.h at the same time
And the patch then migrates mach-imx and mach-mx5 to the updated
driver by adding corresponding platform devices.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
GPIO drivers are getting moved to drivers/gpio for cleanup and
consolidation. This patch moves the plat-mxc driver. Follow up
patches will clean it up and make it a fine upstanding gpio driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The patch makes necessary changes on gpio-mxs as below to turn it
into an upstanding gpio driver.
* Clean up the gpio port definition stuff
* Use readl/writel to replace mach-specific accessors
__raw_readl/__raw_writel
* Change mxs_gpio_init into mxs_gpio_probe function
And it then migrates mach-mxs to the updated driver by adding
corresponding platform devices.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
GPIO drivers are getting moved to drivers/gpio for cleanup and
consolidation. This patch moves the mxs driver. Follow up patches
will clean it up and make it a fine upstanding example of a gpio
driver.
v2: Removed header file entirely and put struct definition directly
into driver. The struct isn't used anywhere else in the kernel.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
The Samsung GPIO drivers are always built-in when the relevant
platform is selected. Change the Kconfig symbol to def_bool y
dependant on the platform.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Remove the #define GEN_74X164_GPIO_COUNT since it's only used in
one place and it's meaning is obvious. Also remove the #define
GEN_74X164_DRIVER_NAME and use spi->modalias to set the gpio chip's
label and the string "74x164" for the driver name.
Reorder the code slightly to remove the need to prototype
gen_74x164_set_value.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
After the GPIO driver move, some symbols became selectable when they
shouldn't be. Tighten the dependencies.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We had a few drivers move from arch/arm into drivers/gpio, but they
don't actually compile without the ARM platform headers etc. As a
result they were messing up allyesconfig on x86.
Make them depend on ARM.
Reported-by: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6:
gpio/pch_gpio: Support new device ML7223
gpio: make gpio_{request,free}_array gpio array parameter const
GPIO: OMAP: move to drivers/gpio
GPIO: OMAP: move register offset defines into <plat/gpio.h>
gpio: Convert gpio_is_valid to return bool
gpio: Move the s5pc100 GPIO to drivers/gpio
gpio: Move the s5pv210 GPIO to drivers/gpio
gpio: Move the exynos4 GPIO to drivers/gpio
gpio: Move to Samsung common GPIO library to drivers/gpio
gpio/nomadik: add function to read GPIO pull down status
gpio/nomadik: show all pins in debug
gpio: move Nomadik GPIO driver to drivers/gpio
gpio: move U300 GPIO driver to drivers/gpio
langwell_gpio: add runtime pm support
gpio/pca953x: Add support for pca9574 and pca9575 devices
gpio/cs5535: Show explicit dependency between gpio_cs5535 and mfd_cs5535
Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
gpio_{request,free}_array should not (and do not) modify the passed gpio
array, so make the parameter const.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
GPIO 1 to 8 are added for TPS65911 chip version. The gpio driver
now handles more than one gpio lines. Subsequent versions of the
chip family can add new GPIO lines with minimal driver changes.
Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The GPIO driver should reside in drivers/gpio/ for better
organization.
Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Move the Samsung s5pc100 SoC GPIO driver to drivers/gpio
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Move the Samsung s5pv210 SoC GPIO driver to drivers/gpio
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Move the Samsung Exynos4 series SoCs GPIO driver to drivers/gpio
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It's common gpiolib for recent Samsung SoCs. Move to drivers/gpio
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Useful to check the status of the runtime pin muxing.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
[Squashed, modified to use chip-internal IRQ trigger state]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This moves the Nomadik GPIO driver out of arch/arm/plat-nomadik
and into the desired location indicated by the subsystem
maintainer.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[grant.likely: squashed with kconfig fixup]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This moves the U300 GPIO driver out of arch/arm/mach-u300 and into
the desired location indicated by the subsystem maintainer.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
While this is essentially a no-op for this driver, it has the
side effect of letting the PMU driver snoop D3 requests from
the PCI core for this driver.
This is only for langwell, not for whitney point.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
PCA957x is i2c gpio expander, and similar to PCA953x. Although register
configurations are different between PCA957x and PCA953x. They can share
a lot of components, such as IRQ handling, GPIO IN/OUT. So updating PCA953x
driver to support PCA957x chips.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
cs5535-gpio.c has been split into two, with various setup moved
into cs5535-mfd.c. Given that cs5535-gpio will not load without
the -mfd part, lets make that dependency explicit in Kconfig
Signed-off-by: Ed Wildgoose <kernel@wildgooses.com>
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6:
gpio/via: rename VIA local config struct
basic_mmio_gpio: split into a gpio library and platform device
gpio: remove some legacy comments in build files
gpio: add trace events for setting direction and value
gpio/pca953x: Use handle_simple_irq instead of handle_edge_irq
gpiolib: export gpiochip_find
gpio: remove redundant Kconfig depends on GPIOLIB
basic_mmio_gpio: convert to non-__raw* accessors
basic_mmio_gpio: support direction registers
basic_mmio_gpio: support different input/output registers
basic_mmio_gpio: detect output method at probe time
basic_mmio_gpio: request register regions
basic_mmio_gpio: allow overriding number of gpio
basic_mmio_gpio: convert to platform_{get,set}_drvdata()
basic_mmio_gpio: remove runtime width/endianness evaluation
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With the addition of a device platform mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Acked-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
alpha allmodconfig:
drivers/gpio/ml_ioh_gpio.c: In function 'ioh_gpio_probe':
drivers/gpio/ml_ioh_gpio.c:205: error: implicit declaration of function 'kzalloc'
drivers/gpio/ml_ioh_gpio.c:205: warning: assignment makes pointer from integer without a cast
also fix this:
drivers/gpio/ml_ioh_gpio.c:145: warning: 'ioh_gpio_save_reg_conf' defined but not used
drivers/gpio/ml_ioh_gpio.c:154: warning: 'ioh_gpio_restore_reg_conf' defined but not used
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alpha allmodconfig:
drivers/gpio/vx855_gpio.c: In function 'vx855gpio_probe':
drivers/gpio/vx855_gpio.c:233: error: implicit declaration of function 'kzalloc'
drivers/gpio/vx855_gpio.c:233: warning: assignment makes pointer from integer without a cast
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow GPIO_BASIC_MMIO_CORE to be used to provide an accessor library
for implementing GPIO drivers whilst abstracting the register access
detail. Based on a patch from Anton Vorontsov[1] and adapted to allow
bgpio_chip to be embedded in another structure.
Changes since v1:
- Register the gpio_chip in the platform device probe
1. https://lkml.org/lkml/2011/4/19/401
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The build files for drivers/gpio has some wording and comments
about the directory being reserved exclusively for GPIO expanders
(according to the gpio.txt file these are on external busses) and
this has been false for some time. We already have PL061 and
Xilinx drivers which are in silicon and now I'm moving more
silicon drivers here, so delete this and reword it a bit.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch allows to trace gpio operations using ftrace
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Make pca953x driver use the simple irq handler since no hardware control
is necessary and the driver lacks an irq_ack function. handle_edge_irq()
calls chip->irq_ack() which crashes since this function does not exist.
Signed-off-by: Erik Botö <erik.boto@pelagicore.com>
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Export function gpiochip_find so that modules can use it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Since all the drivers are in a 'if GPIOLIB/endif block', the depends on GPIOLIB
is redundant so remove them.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The __raw_* accessors don't include memory barriers and can cause
problems when writes get stuck in write buffers.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Most controllers require the direction of a GPIO to be set by writing to
a direction register. Add support for either an input direction
register or an output direction register.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Some controllers have separate input and output registers. For these
controllers, use "set" for the output and "dat" for the input.
Changes since v2: reuse "set" for output and "dat" for input rather than
adding a new "in" register.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Rather than detecting the output method each time in the .set()
callback, do it at probe time and set the appropriate callback.
Changes since v2: moved the reg_dat initialization into
bgpio_setup_io().
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Make sure that we get the register regions with request_mem_region()
before ioremap() to make sure we have exclusive access.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Some platforms may have a number of GPIO that is less than the register
width of the peripheral.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Use the platform drvdata helpers rather than working on the struct
device itself.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Remove endianness/width calculations at runtime by installing function
pointers for bit-to-mask conversion and register accessors.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Using C line continuation inside format strings is error prone.
Clean up the unintended whitespace introduced by misuse of \.
Neaten correctly used line continations as well for consistency.
drivers/scsi/arcmsr/arcmsr_hba.c has these errors as well,
but arcmsr needs a lot more work and the driver should likely be
moved to staging instead.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'spi/merge' of git://git.secretlab.ca/git/linux-2.6:
dt/fsldma: fix build warning caused by of_platform_device changes
spi: Fix race condition in stop_queue()
gpio/pch_gpio: Fix output value of pch_gpio_direction_output()
gpio/ml_ioh_gpio: Fix output value of ioh_gpio_direction_output()
gpio/pca953x: fix error handling path in probe() call
The pch_gpio_direction_output() function was missing a write to set the
desired output value. The function would properly set the GPIO
direction, but not the output value. The value would have to manually
be set with a follow up call to pch_gpio_set().
Add the missing write so that pch_gpio_direction_output() sets both the
GPIO direction and value.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The ioh_gpio_direction_output() function was missing a write to set the
desired output value. The function would properly set the GPIO
direction, but not the output value. The value would have to manually
be set with a follow up call to ioh_gpio_set().
Add the missing write so that ioh_gpio_direction_output() sets both the
GPIO direction and value.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
If the device fails to respond, then the error path tries to remove an
interrupt that never got registered, which causes an backtrace from the
interrupt handling code.
Fix this by ensuring that the cleanup path has two labels and use the
correct path as needed.
fixes the following error:
WARNING: at kernel/irq/manage.c:908 __free_irq+0x80/0x160()
Trying to free already-free IRQ 0
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This driver is broken in several aspects.
1) old style irq_chip functions. Sigh
2) Abuse of the unlock callback. That's not supposed to be a state
machine for evrything and some more.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To get rid of port expanders, the free GPIOs of ab8500
can be used. There are 42 GPIO pins. Out of which 16
are interrupt capable.This patch implements 16 virtual
IRQ mapped to 16 interrupt capable AB8500 GPIOs.
Signed-off-by: Bibek Basu <bibek.basu@stericsson.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
[Renamed header file as per MFD structure]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Converted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
LKML-Reference: <20110324212509.118888535@linutronix.de>
Converted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
LKML-Reference: <20110324212509.025730689@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
gpiolib plus two gpio implementations in arm fiddle in the guts of
irq_desc in a racy and buggy way. Remove the stuff. I already told the
gpio folks that we can provide that information in a proper way if
necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
LKML-Reference: <20110324212508.931638262@linutronix.de>
Almost the same driver for both Poulsbo and Tunnel Creek.
The difference is in quantity of GPIOs powered by the core power
rail and by suspend power supply, default values for some GPIOs, etc.
Detect actual hardware by platform device ID assigned in lpc_sch
and set configuration accordingly.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use mfd_data for passing information from mfd drivers to soc
clients. The mfd_cell's driver_data field is being phased out.
Clients that were using driver_data now access .mfd_data
via mfd_get_data().
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.
Note that the mfd's platform_data is marked __devinitdata. This
is still correct in all cases except for the timbgpio driver, whose
remove hook has been changed to no longer reference the pdata.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'spi/next' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
spi/dw_spi: move dw_spi.h into drivers/spi
spi/dw_spi: Fix missing header
gpio/langwell: Clear edge bit before handling
gpio/langwell: Simplify demux loop
gpio/langwell: Convert irq name space
gpio/langwell: Fix broken irq_eoi change.
gpio; Make Intel chipset gpio drivers depend on x86
gpio/cs5535-gpio: Fix section mismatch
spi/rtc-{ds1390,ds3234,m41t94}: Use spi_get_drvdata() for SPI devices
spi/davinci: Support DMA transfers larger than 65535 words
spi/davinci: Use correct length parameter to dma_map_single calls
gpio: Use __devexit at necessary places
gpio: add MODULE_DEVICE_TABLE to pch_gpio and ml_ioh_gpio
gpio/mcp23s08: support mcp23s17 variant
of_mmc_spi: add card detect irq support
spi/omap_mcspi: catch xfers of non-multiple SPI word size
spi/omap_mcspi: Off-by-one error in finding the right divisor
gpio/pca953x: Fix wrong pointer type
spi/pl022: rid dangling labels
spi: add support for SuperH SPI
...
I don't have the specs for this beast, but it looks a lot like the PXA
GPIO block. Though I bet it's the same IP and the driver should have
reused the PXA code.
Acknowleding the edge detect status after handling one or more gpio
interrupts looks wrong. We might lose an edge which came in while we
handled the previous one.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Alek Du <alek.du@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'defcfg' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6647/1: add Versatile Express defconfig
ARM: 6644/1: mach-ux500: update the U8500 defconfig
* 'drivers' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6764/1: pl011: factor out FIFO to TTY code
ARM: 6763/1: pl011: add optional RX DMA to PL011 v2
ARM: 6758/1: amba: support pm ops
ARM: amba: make amba_driver id_table const
ARM: amba: make internal ID table handling const
ARM: amba: make probe() functions take const id tables
ARM: 6662/1: amba: make amba_bustype non-static
ARM: mmci: add dmaengine-based DMA support
ARM: mmci: no need for separate host->data_xfered
ARM: mmci: avoid unnecessary switch to data available PIO interrupts
ARM: mmci: no need to call flush_dcache_page() with sg_miter API
ARM: mmci: avoid reporting too many completed bytes on fifo overrun
ALSA: AACI: make fifo variables more explanitory
ALSA: AACI: no need to call snd_pcm_period_elapsed() for each period
ALSA: AACI: use snd_pcm_lib_period_bytes()
ALSA: AACI: clean up AACI announcement printk
ALSA: AACI: fix channel mask selection
ALSA: AACI: fix number of channels for record
ALSA: AACI: fix multiple IRQ claiming
* 'cyberpro-next' of master.kernel.org:/home/rmk/linux-2.6-arm:
VIDEO: cyberpro: remove unused cyber2000fb_get_fb_var()
VIDEO: cyberpro: remove useless function extreg pointers
VIDEO: cyberpro: update handling of device structures
VIDEO: cyberpro: add support for video capture I2C
VIDEO: cyberpro: make 'reg_b0_lock' always present
VIDEO: cyberpro: add I2C support
VIDEO: cyberpro: select lowest multipler/divisor for PLL
Use __ffs() to find the pending interrupt source instead of looping 32
times.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Convert to the new irq function names.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 0766d20fd (langwell_gpio: modify EOI handling following change
of kernel irq subsystem) changes
- desc->chip->eoi(irq);
+
+ if (desc->chip->irq_eoi)
+ desc->chip->irq_eoi(irq_get_irq_data(irq));
+ else
+ dev_warn(pg->chip.dev, "missing EOI handler for irq %d\n", irq);
With the following explanation:
"Latest kernel has many changes in IRQ subsystem and its interfaces,
like adding irq_eoi" for struct irq_chip, this patch will make it
support both the new and old interface."
This is completely bogus.
#1) The changelog does not match the patch at all
#2) This driver relies on the assumption that it sits behind an eoi
capable interrupt line. If the implementation of the underlying
chip changes from eoi to irq_eoi then this driver has to follow
that change and not add a total bogosity.
#3) Just mechanically changing eoi to irq_eoi without checking the
background of that change is sloppy at best.
Remove the sillyness and retrieve the interrupt data from irq_desc
directly. No need to go through a sparse irq lookup.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Nothing outside of x86 can use that code.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix section mismatch by annotating using variable name suffix.
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Rabin Vincent