Add WMI support to send pdev_set_quiet_mode command to target.
This will be used for thermal mitigation purpose.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.2.4 firmware uses bitmask in wmi_resource_config to configure
10.2 firmware features like airtime fairness and rx batch mode instead
of maintaining separete bool entry. This allows new features that can be
configure during init time without breaking backward compatibility.
kvalo: use WMI op version, bump up FW API to 4 to not break older versions of
ath10k
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The internal firmware version doesn't tell much to the user, it's more
informative to use that field to print the wmi op version.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ATH10K_FW_FEATURE_WMI_10X should not be used for anymore as that's
now deprecated, instead use wmi op version.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To make it easier to manage firmware differences, we should not use
ATH10K_FW_FEATURE_WMI_10X outside ath10k_core_init_firmware_features(). To
achieve that create new field ar->max_num_vdevs and set it based on wmi op
version.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware doesn't allow precise tx rate control so
P2P wasn't entirely spec compliant (it was using
CCK rates in some cases).
The only way to make sure firmware doesn't use CCK
rates is to have a vdev with P2P subtype used for
scanning and tx. This can be done via a special
dedicated P2P device interface support.
This also removes the ancient hack from ath10k in
favor of p2pdev.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Per-vif bss_conf.ps should be used to configure
powersave.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Setting 0 ps timeout to firmware yields very poor
latency and traffic issues. This is the case when
multi-vif is active.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To comply with WMM-PS the device shouldn't wake up
with a NullFunc frame pair when tx-ing. Instead PM
bit on each tx frame should be used.
To make this work correctly firmware needs to be
told to use a different STA PS wake threshold when
u-APSD is enabled.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some firmware revisions need peer phymode to be
specified as MODE_11B when associating as station
to a 11b AP. Otherwise they can starve other
stations.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Setting fragmentation threshold has not been supported by
any of firmware versions, hence unregister the callback and
remove the function.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Pull MIPS updates from Ralf Baechle:
"This is an unusually large pull request for MIPS - in parts because
lots of patches missed the 3.18 deadline but primarily because some
folks opened the flood gates.
- Retire the MIPS-specific phys_t with the generic phys_addr_t.
- Improvments for the backtrace code used by oprofile.
- Better backtraces on SMP systems.
- Cleanups for the Octeon platform code.
- Cleanups and fixes for the Loongson platform code.
- Cleanups and fixes to the firmware library.
- Switch ATH79 platform to use the firmware library.
- Grand overhault to the SEAD3 and Malta interrupt code.
- Move the GIC interrupt code to drivers/irqchip
- Lots of GIC cleanups and updates to the GIC code to use modern IRQ
infrastructures and features of the kernel.
- OF documentation updates for the GIC bindings
- Move GIC clocksource driver to drivers/clocksource
- Merge GIC clocksource driver with clockevent driver.
- Further updates to bring the GIC clocksource driver up to date.
- R3000 TLB code cleanups
- Improvments to the Loongson 3 platform code.
- Convert pr_warning to pr_warn.
- Merge a bunch of small lantiq and ralink fixes that have been
staged/lingering inside the openwrt tree for a while.
- Update archhelp for IP22/IP32
- Fix a number of issues for Loongson 1B.
- New clocksource and clockevent driver for Loongson 1B.
- Further work on clk handling for Loongson 1B.
- Platform work for Broadcom BMIPS.
- Error handling cleanups for TurboChannel.
- Fixes and optimization to the microMIPS support.
- Option to disable the FTLB.
- Dump more relevant information on machine check exception
- Change binfmt to allow arch to examine PT_*PROC headers
- Support for new style FPU register model in O32
- VDSO randomization.
- BCM47xx cleanups
- BCM47xx reimplement the way the kernel accesses NVRAM information.
- Random cleanups
- Add support for ATH25 platforms
- Remove pointless locking code in some PCI platforms.
- Some improvments to EVA support
- Minor Alchemy cleanup"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (185 commits)
MIPS: Add MFHC0 and MTHC0 instructions to uasm.
MIPS: Cosmetic cleanups of page table headers.
MIPS: Add CP0 macros for extended EntryLo registers
MIPS: Remove now unused definition of phys_t.
MIPS: Replace use of phys_t with phys_addr_t.
MIPS: Replace MIPS-specific 64BIT_PHYS_ADDR with generic PHYS_ADDR_T_64BIT
PCMCIA: Alchemy Don't select 64BIT_PHYS_ADDR in Kconfig.
MIPS: lib: memset: Clean up some MIPS{EL,EB} ifdefery
MIPS: iomap: Use __mem_{read,write}{b,w,l} for MMIO
MIPS: <asm/types.h> fix indentation.
MAINTAINERS: Add entry for BMIPS multiplatform kernel
MIPS: Enable VDSO randomization
MIPS: Remove a temporary hack for debugging cache flushes in SMTC configuration
MIPS: Remove declaration of obsolete arch_init_clk_ops()
MIPS: atomic.h: Reformat to fit in 79 columns
MIPS: Apply `.insn' to fixup labels throughout
MIPS: Fix microMIPS LL/SC immediate offsets
MIPS: Kconfig: Only allow 32-bit microMIPS builds
MIPS: signal.c: Fix an invalid cast in ISA mode bit handling
MIPS: mm: Only build one microassembler that is suitable
...
Introduce a new wmi interface controls noise floor (NF) calibration
period via debugfs as firmware has introduced it on v10.2.
It allows users to modify frequency of NF calibration in millisecond
and changes RSSI reporting frequency consequently.
Short calibration period will trigger more frequent NF calibration,
so that RSSI reported in receive frames is more realistic.
Till now calibration was done at 30 seconds.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New pdev paramters have been added to firmware 10.2,
hence update wmi interfaces to sync with.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Latest main firmware branch introduced a new WMI
ABI called wmi-tlv. It is not a tlv strictly
speaking but something that resembles it because
it is ordered and may have duplicate id entries.
This prepares ath10k to support new hw.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some functions can be shared across different WMI
ABIs. Make them public so different WMI backends
can use them from different source files in the
future.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since the 10.x fw branch support was introduced it
became apparent ath10k will need to be able to
deal with different fw ABIs eventually.
The patch creates an abstraction for dealing with
command and event structures across different ABIs
and mostly gets rid of the
ATH10K_FW_FEATURE_WMI_10X flag usage.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This splits the actual event parsing into
intermediary structures to facilitate future
support of vastly different ABI WMI backends.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Instead of using feature flags, add new 32 bit variable for managing different
WMI versions. This makes it firmware interface tests a bit less convoluted,
especially when we add one more interface.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's easier to manage firmware version differences when we configure them in
one place. Rename ath10k_core_init_max_sta_count() to
ath10k_core_init_firmware_features() and start moving most of the firmware
version ("features") handling to that function.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the error handling style preferred in ath10k. Makes it easier to add
ath10k_init_firmware_features() function in the next patch.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will make it possible to easily support
different hardware with different uart pin
configuration.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes it easier to extend the list of
supported hardware.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will make it easier to extend and maintain
list of supported hardware.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds support for reading calibration data from Device Tree.
It looks for the calibration data in Device Tree if it can't find it
in a file. If there's no node in Device Tree, ath10k will try to find the
calibration data from OTP.
The node for the calibration data should be defined like this:
pci {
pcie@0 {
reg = <0 0 0 0 0>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
device_type = "pci";
ath10k@0,0 {
reg = <0 0 0 0 0>;
device_type = "pci";
qcom,ath10k-calibration-data = [ 01 02 03 ... ];
};
};
};
Signed-off-by: Toshi Kikuchi <toshik@chromium.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This reverts commit d32394fae9.
It has been reported to cause problems, Jeremiah writes:
On an Acer C720 laptop if a suspend is performed the screen
freezes, the machine locks up, and according to the indicator
lights it does not enter suspend. A hard reset is required to
get it running again.
Reported-by: Jeremiah Mahler <jmmahler@gmail.com>
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hardware doesn't place any restrictions on the buffer alignment,
consider this TODO resolved.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If card reset with firmware download executed, followed by reset
with use of firmware from build in flash, firmware download indication
remains in the hardware register.
When running firmware download flow,
the SW download indication is written by the driver to bit 0 in usage_6:
wil_fw_load(), "S(RGF_USER_USAGE_6, 1);"
This register, like all USER RGF, wasn't reset in SW reset flow.
Therefore the driver must clear it on SW reset flow.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the wil_tx_ring, error message printed when tx attempted
while vring has no space to accommodate all fragments of frame.
Normally, such situation handled by stopping tx queue.
But, if tx queue is by-passed (like pktgen does), this error
will be triggered at high rate and dmesg will be flooded with
this message. Whole system may become unstable and hang with
no possible recover except power cycle.
Rate-limit it to prevent dmesg flooding.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some compilation environments, result of pointer arithmetic interpreted as int
while in others it is long int. Force conversion to long.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow to configure VRING size for both Rx and Tx via module parameters:
rx_ring_order and tx_ring_order. Parameters are ring size orders, i.e.
ring size calculated as 1 << order.
Defaults for both Tx and Rx are order 9, i.e. size 512
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to obtain physical device through
wil->pdev->dev path, as it is done by this macro.
The same device already stored as wiphy's device, thus
wil_to_dev() returns the same device as wil_to_pcie_dev()
Remove unnecessary macros, this allows to drop dependency
by pci.h in the firmware download code.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Scan timeout treated as indication for firmware error;
and should be handled in the same way.
Recovery state machine does not perform as designed because
its state is not updated in case of scan timeout.
Fix is to set recovery state machine into the proper state.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX_HTRSH interrupt is handled in exactly the same manner
as RX_DONE interrupt - fetching accumulated packets from RX
ring. In addition there's a rate limitted warning message.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Propagate reason for the disconnect through the relevant call chains:
- report to cfg80211 reason as reported by the firmware
- provide to the firmware reason as requested by cfg80211
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of killing interrupts during reset when the first one happens,
kill them before issuing the reset.
This fixes an easy to reproduce crash with multiple cards sharing the
same IRQ.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IRQs are suppressed if ah == NULL and ATH_OP_INVALID being set in
common->op_flags. Close a short time window between those two.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Like with ath9k, ath5k queues also need to be ordered by priority.
queue_info->tqi_subtype already contains the correct index, so use it
instead of relying on the order of ath5k_hw_setup_tx_queue calls.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware queues are ordered by priority. Use queue index 0 for BK, which
has lower priority than BE.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver passes the desired hardware queue index for a WMM data queue
in qinfo->tqi_subtype. This was ignored in ath9k_hw_setuptxqueue, which
instead relied on the order in which the function is called.
Cc: stable@vger.kernel.org
Reported-by: Hubert Feurstein <h.feurstein@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix missing memory deallocation on error paths in wil_write_file_wmi()
and wil_write_file_txmgmt().
Reported-by: Ahmed Tamrawi <ahmedtamrawi@gmail.com>
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't bother with fancy arithmetic and just
hardcode the final values.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In theory it was possible to starve the system if
a tx/rx handler could implicitly trigger more
tx/rx pci events.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pass the eid argument via skbuff control buffer.
This will make it possible to work with queues of
HTC event buffers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This wasn't used since forever and there are no
plans on using it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The service bitmap can be used to determine
firmware capabilities.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This shouldn't really happen but take into account
the original service bitmap length when mapping
service ids.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The dump print uses sizeof() but since service_map
was a mere pointer the dump was too short.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Traces shouldn't modified passed data. This will
make it possible to pass const arguments to
traces.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Increase the rts threshold from the legacy value of 2347 to support higher
threshold limit.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the helper to get rid of the file operations per debugfs file. The
struct ath9k_softc pointer is set as device driver data to be obtained
in the seq_file read operation.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The debugfs files that are defined in debug.c which are read-only
and using a simple_open as .open file operation have been modified
to use the single_open seq_file API. This simplifies the read
functions defining the file contents.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The number of peers isn't directly translatable to
the number of stations because ath10k needs to
reserve a few extra peers for special cases like
multi-vif concurrency.
The previous limit was 126 and 15 stations in AP
mode for 10.x and main firmware branches
respectively. The limit is now 128 and 16 which
was the original intention.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The var was supposed to be protected by data_lock
but it wasn't so in all instances. It's actually
not necessary to have a spinlock protected
num_peers so drop it.
All instances of num_peers are already within
conf_mutex sections so use that.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This prevents warning spamming if peer creation
fails during sta_state in some cases.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add mem_val debugfs file for dumping the firmware (target) memory and also for
writing to the memory. The firmware memory is accessed through one file which
uses position of the file as the firmware memory address. For example, with dd
use skip parameter for the address.
Beucase target memory width is 32 bits it's strongly recommended to use
blocksize divisable with 4 when using this interface. For example, when using
dd use bs=4 to set the block size to 4 and remember to divide both count and
skip values with four.
To read 4 kB chunk from address 0x400000:
dd if=mem_value bs=4 count=1024 skip=1048576 | xxd -g1
To write value 0x01020304 to address 0x400400:
echo 0x01020304 | xxd -r | dd of=mem_value bs=4 seek=1048832
To read 4 KB chunk of memory and then write back after edit:
dd if=mem_value of=tmp.bin bs=4 count=1024 skip=1048576
emacs tmp.bin
dd if=tmp.bin of=mem_value bs=4 count=1024 seek=1048576
Signed-off-by: Yanbo Li <yanbol@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Debugfs files reg_addr and reg_val are used for reading and writing to the
firmware (target) registers. reg_addr contains the address to be accessed,
which also needs to be set first, and reg_value is when used for reading and
writing the actual value in ASCII.
To read a value from the firmware register 0x100000:
# echo 0x100000 > reg_addr
# cat reg_value
0x00100000:0x000002d3
To write value 0x2400 to address 0x100000:
# echo 0x100000 > reg_addr
# echo 0x2400 > reg_value
#
Signed-off-by: Yanbo Li <yanbol@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_tx_wep_key_work() acquires conf_mutex, so
cancelling it when conf_mutex is already taken
in ath10k_remove_interface() is incorrect, so
move it outside the lock.
Snippet from the lockdep report:
kernel: ======================================================
kernel: [ INFO: possible circular locking dependency detected ]
kernel: 3.18.0-rc5-wl-debug #34 Tainted: G O
kernel: -------------------------------------------------------
kernel: hostapd/451 is trying to acquire lock:
kernel: ((&arvif->wep_key_work)){+.+...}, at: [<ffffffff810872d5>] flush_work+0x5/0x290
kernel: but task is already holding lock:
kernel: (&ar->conf_mutex){+.+.+.}, at: [<ffffffffa0b99f00>] ath10k_remove_interface+0x40/0x290 [ath10k_core]
kernel: which lock already depends on the new lock.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
peer->keys needs to be protected by data_lock
since it is also accessed from the WMI path.
Both install() and clear() routines for peer
keys modify the key contents, so use the data_lock
to avoid races.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When static keys are used in shared WEP, when a
station is associated, message 3 is sent with an
encrypted payload. But, for subsequent
authentications that are triggered without a
deauth, the auth frame is decrypted by the HW.
To handle this, check if the WEP keys have already
been set for the peer and if so, mark the
frame as decrypted. This scenario can happen
when a station changes its default TX key and initiates
a new authentication sequence.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some firmware revisions don't seem to deilver
management frames with FCS error via WMI so narrow
down the HTT rule to not drop corrupted management
frames.
This basically increases number of frames ath10k
reports while sniffing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When mac80211 requests driver to cancel a hw roc
the driver must not call the expired() callback or
else roc will fail in some cases depending on how
things get scheduled.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With P2P concurrency requested hw roc duration
time can be very small. Some firmware revisions
refuse scan requests with too small channel dwell
time.
This prevents messages like, e.g. with connected
STA vif and performing P2P Find:
ath10k_pci 0000:00:05.0: failed to switch to channel for roc scan
ieee80211 phy3: failed to start next HW ROC (-110)
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New firmware revisions don't need peer creation
when doing offchannel tx. Earlier revisions would
queue and never release frames without a peer.
This prevent new firmware revisions from stopping
replenishing wmi-htc tx credits and improves
reliability of offchannel tx which would sometimes
silently fail.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Comment was out-of-date. The headroom is no longer
necessary because HTT Tx fragment list is stored
in dma pool item associated with each sk_buff.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When re-associating a station, the nss was set back to
maximum value even if user had configured small number
of tx chains. So, pay attention to user's config in
this case as well.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It appears it takes more than just setting the
hardware's chainmask to make things work well. Without
this patch, a vdev would only use 1x1 rates when chainmask
was set to 0x3.
Setting the 'nss' (number of spatial streams) on the vdev
helps the firmware's rate-control algorithm work properly.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add TPC capability to TX descriptor path. Cap per-packet TX power according to
TX power per-rate tables. Currently TPC is supported just by AR9003 based chips
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add TX power per-rate tables for different MIMO modes (e.g STBC) in order to
cap the maximum TX power value per-rate in the TX descriptor path.
Cap TX power for self generated frames (ACK, RTS/CTS).
Currently TPC is supported just by AR9003 based chips
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For FCC and JP, in one of the radar patterns, PPB and PRF seems to be
interchanged leading to frequent incorrect radar detections.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are not many of these messages producted by the
firmware, but they are generally fairly useful, so make it easy to print them
with a separate debug level.
kvalo: fix commit log, rename debug level
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are better ways to get the kernel information, use the
utsname and omit the version code entirely since it's duplicate.
The version magic is rather useless anyway
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
- Use config symbol defined in the driver instead of arch specific one for
conditional compilation.
- Rename the ATHEROS_AR231X config symbol to ATH25.
- Fix include (ar231x_platform.h -> ath25_platform.h).
- Some of AR231x SoCs (e.g. AR2315) have PCI bus support, so remove !PCI
dependency, which block AHB support build.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: linux-wireless@vger.kernel.org
Cc: ath5k-devel@lists.ath5k.org
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8248/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This reverts commit 093ec3c533.
AHB bus code has been removed, since we did not have support Atheros
AR231x SoC, required for building the AHB version of ath5k. Now that
support WiSoC chips added we can restore functionality back.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: linux-wireless@vger.kernel.org
Cc: ath5k-devel@lists.ath5k.org
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8247/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
another relatively large set of changes:
* TDLS off-channel support set from Arik/Liad, with some support
patches I did
* custom regulatory fixes from Arik
* minstrel VHT fix (and a small optimisation) from Felix
* add back radiotap vendor namespace support (myself)
* random MAC address scanning for cfg80211/mac80211/hwsim (myself)
* CSA improvements (Luca)
* WoWLAN Net Detect (wake on network found) support (Luca)
* and lots of other smaller changes from many people
-----BEGIN PGP SIGNATURE-----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=q4e6
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-11-20' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"It has been a while since my last pull request, so we accumulated
another relatively large set of changes:
* TDLS off-channel support set from Arik/Liad, with some support
patches I did
* custom regulatory fixes from Arik
* minstrel VHT fix (and a small optimisation) from Felix
* add back radiotap vendor namespace support (myself)
* random MAC address scanning for cfg80211/mac80211/hwsim (myself)
* CSA improvements (Luca)
* WoWLAN Net Detect (wake on network found) support (Luca)
* and lots of other smaller changes from many people"
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fragmented Rx wasn't reporting everything. With
the reworked Rx code it's very easy to fix it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes it more in line with the new Rx path.
It also makes the code more reusable because Rx
descriptor is more accessible.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The original fix has been moved into a different
place in the code.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This creates a single, common path for MSDU,
A-MSDU and fragmented Rx.
Hopefully this will make it easier to understand
Rx path and make it easier to work with.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make the rx_confused be handled by the rx
indication handlers instead of the buffer popping
function.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since htt_rx_mpdu_status isn't used anymore
(instead attention flags are used) simplify the
loop.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Instead of using manual sk_buff linking via ->next
use sk_buff_head. It's more robust, cleaner and
there's plenty of helper functions in kernel
already to manage sk_buff_head.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
currently ath9k_common depends on this components.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow drivers to support NL80211_SCAN_FLAG_RANDOM_ADDR with software
based scanning and generate a random MAC address for them for every
scan request with the flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, when a roc period expires, the offchannel
timer calls ieee80211_remain_on_channel_expired(), but
the roc state is cleared only when the queued work
to switch to the operating channel gets a chance to run.
This race is a problem because mac80211 can issue a
new roc request in this window. To avoid this, handle
roc completion in the offchannel timer itself.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In a GO/STA setup, when we switch to the STA context,
the channel context timer is scheduled with a period of
half the beacon interval. If a beacon is received in
this duration, the timer is adjusted to accommodate
TSF sync done by the HW.
But, if the actual channel switch is delayed for some
reason, we end up rearming the timer every time a new
beacon is received. Avoid this by doing the adjustment
only once.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If for some reason a beacon with a new NoA is
not sent out, then reset the mgd_prepare_tx flag.
Not doing this will result in a situation where
a GO will send a new NoA when it shouldn't.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes sure that pending roc/scan
operations are cancelled properly when a new
context is assigned/unassigned.
The flush_work() call to flush out any scheduled
channel context work is removed, instead, sc->mutex
is dropped to allow any pending work to get a chance
to complete by the channel scheduler. Also, increase
the timeout to allow a switch to an active GO.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a pending roc or scan operation is cancelled,
the offchannel operation is cleared, but the offchannel
state in the main scheduler is not cleared. This causes
problems since an active GO will try to process a stale
offchannel request that was deferred earlier. Fix this
by clearing the state when there is no pending offchannel
(roc/scan) operation.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The registers that control the on-chip thermometer
need to be programmed based on the chainmask that
the solution supports, not the chainmask that is
present in the eeprom.
Cc: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The base TSF is used for HW timers 0..7, but chips
in the AR9003 family and above can support more generic
timers. To use them, however, a second HW TSF needs to
be enabled. This patch allows usage of the extra
timers by starting the second TSF properly.
The extra set of HW timers is apparently also present
in AR9287, but we enable it only for the AR9003 family.
Cc: Kobi Cohen-Arazi <kobic@qti.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some x86 platforms, the LED gpio is active high
instead of active low. Identify such cards and modify
the GPIO usage to make sure LED works properly.
Cc: Russell Hu <rhu@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates the initvals for QCA953x v1.1 and v2.0
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan