These are all the driver updates for SoC specific drivers. There
are a couple of subsystems with individual maintainers picking up
their patches here:
- The reset controller subsystem add support for a few new SoC
variants to existing drivers, along with other minor improvements
- The OP-TEE subsystem gets a driver for the ARM FF-A transport
- The memory controller subsystem has improvements for Tegra,
Mediatek, Renesas, Freescale and Broadcom specific drivers.
- The tegra cpuidle driver changes get merged through this
tree this time. There are only minor changes, but they depend
on other tegra driver updates here.
- The ep93xx platform finally moves to using the drivers/clk/
subsystem, moving the code out of arch/arm in the process.
This depends on a small sound driver change that is included
here as well.
- There are some minor updates for Qualcomm and Tegra specific
firmware drivers.
The other driver updates are mainly for drivers/soc, which contains
a mixture of vendor specific drivers that don't really fit elsewhere:
- Mediatek drivers gain more support for MT8192, with new support for
hw-mutex and mmsys routing, plus support for reset lines in the
mmsys driver.
- Qualcomm gains a new "sleep stats" driver, and support for
the "Generic Packet Router" in the APR driver.
- There is a new user interface for routing the UARTS on ASpeed
BMCs, something that apparently nobody else has needed so far.
- More drivers can now be built as loadable modules, in particular
for Broadcom and Samsung platforms.
- Lots of improvements to the TI sysc driver for better suspend/resume
support
Finally, there are lots of minor cleanups and new device IDs for
amlogic, renesas, tegra, qualcomm, mediateka, samsung, imx, layerscape,
allwinner, broadcom, and omap.
-----BEGIN PGP SIGNATURE-----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=tUuj
-----END PGP SIGNATURE-----
Merge tag 'drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are all the driver updates for SoC specific drivers. There are a
couple of subsystems with individual maintainers picking up their
patches here:
- The reset controller subsystem add support for a few new SoC
variants to existing drivers, along with other minor improvements
- The OP-TEE subsystem gets a driver for the ARM FF-A transport
- The memory controller subsystem has improvements for Tegra,
Mediatek, Renesas, Freescale and Broadcom specific drivers.
- The tegra cpuidle driver changes get merged through this tree this
time. There are only minor changes, but they depend on other tegra
driver updates here.
- The ep93xx platform finally moves to using the drivers/clk/
subsystem, moving the code out of arch/arm in the process. This
depends on a small sound driver change that is included here as
well.
- There are some minor updates for Qualcomm and Tegra specific
firmware drivers.
The other driver updates are mainly for drivers/soc, which contains a
mixture of vendor specific drivers that don't really fit elsewhere:
- Mediatek drivers gain more support for MT8192, with new support for
hw-mutex and mmsys routing, plus support for reset lines in the
mmsys driver.
- Qualcomm gains a new "sleep stats" driver, and support for the
"Generic Packet Router" in the APR driver.
- There is a new user interface for routing the UARTS on ASpeed BMCs,
something that apparently nobody else has needed so far.
- More drivers can now be built as loadable modules, in particular
for Broadcom and Samsung platforms.
- Lots of improvements to the TI sysc driver for better
suspend/resume support"
Finally, there are lots of minor cleanups and new device IDs for
amlogic, renesas, tegra, qualcomm, mediateka, samsung, imx,
layerscape, allwinner, broadcom, and omap"
* tag 'drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (179 commits)
optee: Fix spelling mistake "reclain" -> "reclaim"
Revert "firmware: qcom: scm: Add support for MC boot address API"
qcom: spm: allow compile-testing
firmware: arm_ffa: Remove unused 'compat_version' variable
soc: samsung: exynos-chipid: add exynosautov9 SoC support
firmware: qcom: scm: Don't break compile test on non-ARM platforms
soc: qcom: smp2p: Add of_node_put() before goto
soc: qcom: apr: Add of_node_put() before return
soc: qcom: qcom_stats: Fix client votes offset
soc: qcom: rpmhpd: fix sm8350_mxc's peer domain
dt-bindings: arm: cpus: Document qcom,msm8916-smp enable-method
ARM: qcom: Add qcom,msm8916-smp enable-method identical to MSM8226
firmware: qcom: scm: Add support for MC boot address API
soc: qcom: spm: Add 8916 SPM register data
dt-bindings: soc: qcom: spm: Document qcom,msm8916-saw2-v3.0-cpu
soc: qcom: socinfo: Add PM8150C and SMB2351 models
firmware: qcom_scm: Fix error retval in __qcom_scm_is_call_available()
soc: aspeed: Add UART routing support
soc: fsl: dpio: rename the enqueue descriptor variable
soc: fsl: dpio: use an explicit NULL instead of 0
...
This patch extends sparx5 driver to support also the lan966x. The
process to reset the switch is the same only it has different offsets.
Therefore make the driver more generic and add support for lan966x.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Steen Hegelund <steen.hegelund@microchip.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20211018091522.1113510-3-horatiu.vultur@microchip.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The early reset driver doesn't ever probe, which causes consuming
devices to be unable to probe. Add an empty driver to set this device
as available, allowing consumers to probe.
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Link: https://lore.kernel.org/r/20210920124141.1166544-4-pan@semihalf.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The return value from tegra_bpmp_transfer indicates the success or
failure of the IPC transaction with BPMP. If the transaction
succeeded, we also need to check the actual command's result code.
Add code to do this.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Link: https://lore.kernel.org/r/20210915085517.1669675-2-mperttunen@nvidia.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
After the retirement of MACH_PISTACHIO, the Pistachio Reset Driver is no
longer auto-enabled when building a kernel for Pistachio systems.
Worse, the driver cannot be enabled by the user at all (unless
compile-testing), as the config symbol is invisible.
Fix this partially by making the symbol visible again when compiling for
MIPS, and dropping the useless default. The user still has to enable
the driver manually when building a kernel for Pistachio systems,
though.
Fixes: 104f942b28 ("MIPS: Retire MACH_PISTACHIO")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Link: https://lore.kernel.org/r/2c399e52540536df9c4006e46ef93fbccdde88db.1631610825.git.geert+renesas@glider.be
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The readl_poll_timeout() should complete when the status bit
is a 1, not 0.
Fixes: 4cf176e523 ("reset: Add Broadcom STB RESCAL reset controller")
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210914221122.62315-1-f.fainelli@gmail.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
These are updates for drivers that are tied to a particular SoC,
including the correspondig device tree bindings:
- A couple of reset controller changes for unisoc, uniphier, renesas
and zte platforms
- memory controller driver fixes for omap and tegra
- Rockchip io domain driver updates
- Lots of updates for qualcomm platforms, mostly touching their
firmware and power management drivers
- Tegra FUSE and firmware driver updateѕ
- Support for virtio transports in the SCMI firmware framework
- cleanup of ixp4xx drivers, towards enabling multiplatform
support and bringing it up to date with modern platforms
- Minor updates for keystone, mediatek, omap, renesas.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iD8DBQBhLz215t5GS2LDRf4RAjlHAJ473D0PymaTzv68EuPHThG+DEPifQCdGjLq
QGBB6JidIP8rtEdC+LWBB8I=
=M5+N
-----END PGP SIGNATURE-----
Merge tag 'drivers-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are updates for drivers that are tied to a particular SoC,
including the correspondig device tree bindings:
- A couple of reset controller changes for unisoc, uniphier, renesas
and zte platforms
- memory controller driver fixes for omap and tegra
- Rockchip io domain driver updates
- Lots of updates for qualcomm platforms, mostly touching their
firmware and power management drivers
- Tegra FUSE and firmware driver updateѕ
- Support for virtio transports in the SCMI firmware framework
- cleanup of ixp4xx drivers, towards enabling multiplatform support
and bringing it up to date with modern platforms
- Minor updates for keystone, mediatek, omap, renesas"
* tag 'drivers-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (96 commits)
reset: simple: remove ZTE details in Kconfig help
soc: rockchip: io-domain: Remove unneeded semicolon
soc: rockchip: io-domain: add rk3568 support
dt-bindings: power: add rk3568-pmu-io-domain support
bus: ixp4xx: return on error in ixp4xx_exp_probe()
soc: renesas: Prefer memcpy() over strcpy()
firmware: tegra: Stop using seq_get_buf()
soc/tegra: fuse: Enable fuse clock on suspend for Tegra124
soc/tegra: fuse: Add runtime PM support
soc/tegra: fuse: Clear fuse->clk on driver probe failure
soc/tegra: pmc: Prevent racing with cpuilde driver
soc/tegra: bpmp: Remove unused including <linux/version.h>
dt-bindings: soc: ti: pruss: Add dma-coherent property
soc: ti: Remove pm_runtime_irq_safe() usage for smartreflex
soc: ti: pruss: Enable support for ICSSG subsystems on K3 AM64x SoCs
dt-bindings: soc: ti: pruss: Update bindings for K3 AM64x SoCs
firmware: arm_scmi: Use WARN_ON() to check configured transports
firmware: arm_scmi: Fix boolconv.cocci warnings
soc: mediatek: mmsys: Fix missing UFOE component in mt8173 table routing
soc: mediatek: mmsys: add MT8365 support
...
This patch changes the data type of the variable 'val' from
int to u32.
Addresses-Coverity: argument of type "int *" is incompatible with parameter of type "u32 *"
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/925cebbe4eb73c7d0a536da204748d33c7100d8c.1624448778.git.michal.simek@xilinx.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The ZTE platform support in the simple reset driver has been
removed but the comment in the help wasn't removed so clean
this up too.
Fixes: 89d4f98ae9 ("ARM: remove zte zx platform")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210821094528.294579-1-pbrobinson@gmail.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add support for RZ/G2L USBPHY Control driver. It mainly controls
reset and power down of the USB/PHY.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210719121938.6532-5-biju.das.jz@bp.renesas.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The Microchip Sparx5 switch reset block is only present on Microchip
Sparx5 SoCs. Hence add a dependency on ARCH_SPARX5, to prevent asking
the user about this driver when configuring a kernel without Sparx5
support.
Fixes: 453ed4283b ("reset: mchp: sparx5: add switch reset driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/6e08f6f46123d0712397e901716b48f13fa5dc48.1624627657.git.geert@linux-m68k.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add PDC Global reset signals for Wireless Processor Subsystem (WPSS)
on SC7280 SoCs.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/1619693465-5724-5-git-send-email-sibis@codeaurora.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
- Reset controllers: Adding support for Microchip Sparx5 Switch.
- Memory controllers: ARM Primecell PL35x SMC memory controller
driver cleanups and improvements.
- i.MX SoC drivers: Power domain support for i.MX8MM and i.MX8MN.
- Rockchip: RK3568 power domains support + DT binding updates,
cleanups.
- Qualcomm SoC drivers: Amend socinfo with more SoC/PMIC details,
including support for MSM8226, MDM9607, SM6125 and SC8180X.
- ARM FFA driver: "Firmware Framework for ARMv8-A", defining
management interfaces and communication (including bus model)
between partitions both in Normal and Secure Worlds.
- Tegra Memory controller changes, including major rework to deal
with identity mappings at boot and integration with ARM SMMU
pieces.
-----BEGIN PGP SIGNATURE-----
iQJDBAABCgAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAmDokgYPHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3looP/20uQAjRadPJFdV/B2mpZYqXMI4dIN9g7KJ1
6uEoaGurzYWQQreDXswQ5vFUcQfIudEJ9Im9IF+9BUsFQ2uvPTJ4I+HDN++WH70B
cIsmwwBr7Q4JUVP+O7T2WGtBY69jvHTpJrCCVtyHtwEyL4a1uyfelsAJXbxqaqis
w1lmXNkkSqx5c67H3maNNDRnbutyLL2gO0TYdiBapOcc5V03OYKNnMbDqRTddqyt
4UH4eYkFkNai8UJ476BXHU9ldlWzEkRBib/OKwF9k3oPj9W3kdQ/vd2IKK5a1fTX
jIbOPSRRC8K/9Bxn1KEtdoU0Yy+rlm3xd7DtQl5RyGTD+tHVq3dN55WjoXBY83Yh
r37y7uII9i09tPg5+APSX/jgodsIt4c46dKwvYuWXvB7ziomfsKxQiRanApJG6UX
qS5NCUrlfYWlL302JOTvEtDBePXXiXQ065GuRjM948WMnVzXwEKwYUakGhvXQWMS
jXCcOGW7GhnbY3+Ipn9chyhydHpKSxIb8oBk4cMRJU9jlN2GmjHgW8RMvT2WM6VF
1F8acyMvf6en5tV6f23cjbW+iIMTS5egKNfqi8tdjGVxbowypyJYzjYOhaqk6veJ
jHOmpglTXas0QD3ZRU7vGVlrvHqik8XyRsq3N9CQjVenRCbsQLKZRi1gTbIuspcR
rejqH3Fs
=kPg8
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Olof Johansson:
- Reset controllers: Adding support for Microchip Sparx5 Switch.
- Memory controllers: ARM Primecell PL35x SMC memory controller driver
cleanups and improvements.
- i.MX SoC drivers: Power domain support for i.MX8MM and i.MX8MN.
- Rockchip: RK3568 power domains support + DT binding updates,
cleanups.
- Qualcomm SoC drivers: Amend socinfo with more SoC/PMIC details,
including support for MSM8226, MDM9607, SM6125 and SC8180X.
- ARM FFA driver: "Firmware Framework for ARMv8-A", defining management
interfaces and communication (including bus model) between partitions
both in Normal and Secure Worlds.
- Tegra Memory controller changes, including major rework to deal with
identity mappings at boot and integration with ARM SMMU pieces.
* tag 'arm-drivers-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (120 commits)
firmware: turris-mox-rwtm: add marvell,armada-3700-rwtm-firmware compatible string
firmware: turris-mox-rwtm: show message about HWRNG registration
firmware: turris-mox-rwtm: fail probing when firmware does not support hwrng
firmware: turris-mox-rwtm: report failures better
firmware: turris-mox-rwtm: fix reply status decoding function
soc: imx: gpcv2: add support for i.MX8MN power domains
dt-bindings: add defines for i.MX8MN power domains
firmware: tegra: bpmp: Fix Tegra234-only builds
iommu/arm-smmu: Use Tegra implementation on Tegra186
iommu/arm-smmu: tegra: Implement SID override programming
iommu/arm-smmu: tegra: Detect number of instances at runtime
dt-bindings: arm-smmu: Add Tegra186 compatible string
firmware: qcom_scm: Add MDM9607 compatible
soc: qcom: rpmpd: Add MDM9607 RPM Power Domains
soc: renesas: Add support to read LSI DEVID register of RZ/G2{L,LC} SoC's
soc: renesas: Add ARCH_R9A07G044 for the new RZ/G2L SoC's
dt-bindings: soc: rockchip: drop unnecessary #phy-cells from grf.yaml
memory: emif: remove unused frequency and voltage notifiers
memory: fsl_ifc: fix leak of private memory on probe failure
memory: fsl_ifc: fix leak of IO mapping on probe failure
...
st32mp1 RCC reset driver was moved into stm32mp1 RCC clock driver.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Link: https://lore.kernel.org/r/20210617051814.12018-7-gabriel.fernandez@foss.st.com
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Make reset-berlin driver to be tristate module, support to build as
a module, this is useful for GKI.
Partially reverts commit ed4dba99ca ("reset: berlin: make it
explicitly non-modular")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20210607181015.5b8d3711@xhacker.debian
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Abort instead of returning a new reset control for a reset controller
device that is going to have its module unloaded.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: 61fc413176 ("reset: Add reset controller API")
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210607082615.15160-1-p.zabel@pengutronix.de
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
In case of error, the function devm_platform_get_and_ioremap_resource()
returns ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Fixes: 453ed4283b ("reset: mchp: sparx5: add switch reset driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210519141638.3052456-1-weiyongjun1@huawei.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 77750bc089 ("reset: Add Broadcom STB SW_INIT reset controller driver")
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1620789283-15048-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The driver defined of_device_id table but did not use it with
of_match_table. This prevents usual matching via devicetree and causes
a W=1 warning:
drivers/reset/reset-a10sr.c:111:34: warning:
‘a10sr_reset_of_match’ defined but not used [-Wunused-const-variable=]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 6270068202 ("reset: Add Altera Arria10 SR Reset Controller")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210507112803.20012-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The Intel Gateway reset controller is only present on Intel Gateway
platforms. Hence add a dependency on X86, to prevent asking the user
about this driver when configuring a kernel without Intel Gateway
support.
Fixes: c9aef213e3 ("reset: intel: Add system reset controller driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The Broadcom STB RESCAL reset controller is only present on Broadcom
BCM7216 platforms. Hence add a dependency on ARCH_BRCMSTB, to prevent
asking the user about this driver when configuring a kernel without
BCM7216 support.
Also, merely enabling CONFIG_COMPILE_TEST should not enable additional
code, and thus should not enable this driver by default.
Fixes: 4cf176e523 ("reset: Add Broadcom STB RESCAL reset controller")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Fixes a checkpatch error:
ERROR: Macros with complex values should be enclosed in parentheses
#23: FILE: drivers/reset/reset-uniphier.c:23:
+#define UNIPHIER_RESET_ID_END (unsigned int)(-1)
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Fixes a checkpatch warning:
WARNING: Possible comma where semicolon could be used
#156: FILE: drivers/reset/sti/reset-syscfg.c:156:
+ rc->rst.ops = &syscfg_reset_ops,
+ rc->rst.of_node = dev->of_node;
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The to_ti_syscon_reset_data macro currently only works if the
parameter passed into it is called 'rcdev'.
Fixes a checkpatch --strict issue:
CHECK: Macro argument reuse 'rcdev' - possible side-effects?
#53: FILE: drivers/reset/reset-ti-syscon.c:53:
+#define to_ti_syscon_reset_data(rcdev) \
+ container_of(rcdev, struct ti_syscon_reset_data, rcdev)
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Fixes a checkpatch warning:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
#55: FILE: drivers/reset/reset-berlin.c:55:
+ unsigned offset, bit;
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Fixes checkpatch issues:
CHECK: Alignment should match open parenthesis
#87: FILE: drivers/reset/core.c:87:
+static int of_reset_simple_xlate(struct reset_controller_dev *rcdev,
+ const struct of_phandle_args *reset_spec)
CHECK: Lines should not end with a '('
#540: FILE: drivers/reset/core.c:540:
+static struct reset_control *__reset_control_get_internal(
CHECK: Alignment should match open parenthesis
#603: FILE: drivers/reset/core.c:603:
+struct reset_control *__of_reset_control_get(struct device_node *node,
+ const char *id, int index, bool shared,
CHECK: Alignment should match open parenthesis
#781: FILE: drivers/reset/core.c:781:
+struct reset_control *__devm_reset_control_get(struct device *dev,
+ const char *id, int index, bool shared,
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The Sparx5 Switch SoC has a number of components that can be reset
indiviually, but at least the Switch Core needs to be in a well defined
state at power on, when any of the Sparx5 drivers starts to access the
Switch Core, this reset driver is available.
The reset driver is loaded early via the postcore_initcall interface, and
will then be available for the other Sparx5 drivers (SGPIO, SwitchDev etc)
that are loaded next, and the first of them to be loaded can perform the
one-time Switch Core reset that is needed.
The driver has protection so that the system busses, DDR controller, PCI-E
and ARM A53 CPU and a few other subsystems are not touched by the reset.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Fixes a checkpatch warning:
WARNING: It's generally not useful to have the filename in the file
#3: FILE: drivers/reset/reset-oxnas.c:3:
+ * drivers/reset/reset-oxnas.c
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Fixes checkpatch issues:
ERROR: code indent should use tabs where possible
#86: FILE: drivers/reset/reset-zynqmp.c:86:
+ .reset_id = 0,$
WARNING: please, no spaces at the start of a line
#86: FILE: drivers/reset/reset-zynqmp.c:86:
+ .reset_id = 0,$
ERROR: code indent should use tabs where possible
#87: FILE: drivers/reset/reset-zynqmp.c:87:
+ .num_resets = VERSAL_NR_RESETS,$
WARNING: please, no spaces at the start of a line
#87: FILE: drivers/reset/reset-zynqmp.c:87:
+ .num_resets = VERSAL_NR_RESETS,$
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
We use reset-simple in this patch so that pcie driver can use
devm_reset_control_get() to get this reset data structure and use
reset_control_deassert() to deassert pcie_power_up_rst_n.
Link: https://lore.kernel.org/r/20210504105940.100004-3-greentime.hu@sifive.com
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Stephen Boyd <sboyd@kernel.org>
No surprises in this development cycle, and most of works are about
the fixes and the improvements of the existing code, while a new LED
control layer and a few new drivers have been introduced.
Here are some highlights:
Core:
- A common mute-LED framework was introduced;
used by HD-audio for now, more adaption will follow later.
The former "Mic Mute-LED Mode" mixer control has been replaced with
the corresponding sysfs now.
- User-control management was changed to count consumed bytes instead
of capping by number of elements;
this will allow more controls in the normal usage pattern while
avoiding the possible memory exhaustion DoS
ASoC:
- Continued refactoring and cleanups in ASoC core and generic card
drivers
- Wide range of small cppcheck and warning fixes
- New drivers for Freescale i.MX DMA over rpmsg, Mediatek MT6358
accessory detection, and Realtek RT1019, RT1316, RT711 and RT715
USB-audio:
- Continued improvements and fixes of the implicit feedback mode,
including better support for Pioneer and Roland/BOSS devices
HD-audio:
- Default back to non-buffer preallocation on x86
- Cirrus codec improvements, more quirks for Realtek codecs
Others:
- New virtio sound driver
- FireWire Bebob updates
Note that this PR includes a couple of changes in reset and SPI
drivers, too, and some merge conflicts might happen.
-----BEGIN PGP SIGNATURE-----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=YT3U
-----END PGP SIGNATURE-----
Merge tag 'sound-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"No surprises in this development cycle, and most of work is about the
fixes and the improvements of the existing code, while a new LED
control layer and a few new drivers have been introduced.
Here are some highlights:
Core:
- A common mute-LED framework was introduced. It is used by HD-audio
for now, more adaption will follow later. The former "Mic Mute-LED
Mode" mixer control has been replaced with the corresponding sysfs
now.
- User-control management was changed to count consumed bytes instead
of capping by number of elements; this will allow more controls in
the normal usage pattern while avoiding the possible memory
exhaustion DoS
ASoC:
- Continued refactoring and cleanups in ASoC core and generic card
drivers
- Wide range of small cppcheck and warning fixes
- New drivers for Freescale i.MX DMA over rpmsg, Mediatek MT6358
accessory detection, and Realtek RT1019, RT1316, RT711 and RT715
USB-audio:
- Continued improvements and fixes of the implicit feedback mode,
including better support for Pioneer and Roland/BOSS devices
HD-audio:
- Default back to non-buffer preallocation on x86
- Cirrus codec improvements, more quirks for Realtek codecs
Others:
- New virtio sound driver
- FireWire Bebob updates"
* tag 'sound-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (587 commits)
ALSA: hda/conexant: Re-order CX5066 quirk table entries
ALSA: hda/realtek: Remove redundant entry for ALC861 Haier/Uniwill devices
ALSA: hda/realtek: Re-order ALC662 quirk table entries
ALSA: hda/realtek: Re-order remaining ALC269 quirk table entries
ALSA: hda/realtek: Re-order ALC269 Lenovo quirk table entries
ALSA: hda/realtek: Re-order ALC269 Sony quirk table entries
ALSA: hda/realtek: Re-order ALC269 ASUS quirk table entries
ALSA: hda/realtek: Re-order ALC269 Dell quirk table entries
ALSA: hda/realtek: Re-order ALC269 Acer quirk table entries
ALSA: hda/realtek: Re-order ALC269 HP quirk table entries
ALSA: hda/realtek: Re-order ALC882 Clevo quirk table entries
ALSA: hda/realtek: Re-order ALC882 Sony quirk table entries
ALSA: hda/realtek: Re-order ALC882 Acer quirk table entries
ALSA: usb-audio: Remove redundant assignment to len
ALSA: hda/realtek: Add quirk for Intel Clevo PCx0Dx
ALSA: virtio: fix kernel-doc
ALSA: hda/cirrus: Use CS8409 filter to fix abnormal sounds on Bullseye
ALSA: hda/cirrus: Set Initial DMIC volume for Bullseye to -26 dB
ALSA: sb: Fix two use after free in snd_sb_qsound_build
ALSA: emu8000: Fix a use after free in snd_emu8000_create_mixer
...
The major and big addition this time is to support modularisation of
individual SCMI protocols thus enabling to add support for vendors'
custom SCMI protocol. This changes the interface provided by the SCMI
driver to all the users of SCMI and hence involved changes in various
other subsystem SCMI drivers. The change has been split with a bit of
transient code to preserve bisectability and avoiding one big patch bomb
changing all the users.
This also includes SCMI IIO driver(pulled from IIO tree) and support for
per-cpu DVFS.
-----BEGIN PGP SIGNATURE-----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=WLTW
-----END PGP SIGNATURE-----
Merge tag 'scmi-updates-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/drivers
ARM SCMI updates for v5.13
The major and big addition this time is to support modularisation of
individual SCMI protocols thus enabling to add support for vendors'
custom SCMI protocol. This changes the interface provided by the SCMI
driver to all the users of SCMI and hence involved changes in various
other subsystem SCMI drivers. The change has been split with a bit of
transient code to preserve bisectability and avoiding one big patch bomb
changing all the users.
This also includes SCMI IIO driver(pulled from IIO tree) and support for
per-cpu DVFS.
* tag 'scmi-updates-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux: (41 commits)
firmware: arm_scmi: Add dynamic scmi devices creation
firmware: arm_scmi: Add protocol modularization support
firmware: arm_scmi: Rename non devres notify_ops
firmware: arm_scmi: Make notify_priv really private
firmware: arm_scmi: Cleanup events registration transient code
firmware: arm_scmi: Cleanup unused core transfer helper wrappers
firmware: arm_scmi: Cleanup legacy protocol init code
firmware: arm_scmi: Make references to handle const
firmware: arm_scmi: Remove legacy scmi_voltage_ops protocol interface
regulator: scmi: Port driver to the new scmi_voltage_proto_ops interface
firmware: arm_scmi: Port voltage protocol to new protocols interface
firmware: arm_scmi: Port systempower protocol to new protocols interface
firmware: arm_scmi: Remove legacy scmi_sensor_ops protocol interface
iio/scmi: Port driver to the new scmi_sensor_proto_ops interface
hwmon: (scmi) port driver to the new scmi_sensor_proto_ops interface
firmware: arm_scmi: Port sensor protocol to new protocols interface
firmware: arm_scmi: Remove legacy scmi_reset_ops protocol interface
reset: reset-scmi: Port driver to the new scmi_reset_proto_ops interface
firmware: arm_scmi: Port reset protocol to new protocols interface
firmware: arm_scmi: Remove legacy scmi_clk_ops protocol interface
...
Link: https://lore.kernel.org/r/20210331100657.ilu63i4swnr3zp4e@bogus
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Patches from Krzysztof Kozlowski the cleans up and consolidate support for
SoCFPGA platforms
- Rename ARCH_SOCFPGA into ARCH_INTEL_SOCFPGA
- Consolidate ARCH_STRATIX10 into ARCH_INTEL_SOCFPGA
- Consolidate ARCH_AGILEX into ARCH_INTEL_SOCFPGA
- Consolidate ARCH_N5X into ARCH_INTEL_SOCFPGA
-----BEGIN PGP SIGNATURE-----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=EWtt
-----END PGP SIGNATURE-----
Merge tag 'socfpga_update_for_v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/drivers
SoCFPGA updates for v5.13
- Patches from Krzysztof Kozlowski the cleans up and consolidate support for
SoCFPGA platforms
- Rename ARCH_SOCFPGA into ARCH_INTEL_SOCFPGA
- Consolidate ARCH_STRATIX10 into ARCH_INTEL_SOCFPGA
- Consolidate ARCH_AGILEX into ARCH_INTEL_SOCFPGA
- Consolidate ARCH_N5X into ARCH_INTEL_SOCFPGA
* tag 'socfpga_update_for_v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: socfpga: drop ARCH_SOCFPGA
reset: socfpga: use ARCH_INTEL_SOCFPGA also for 32-bit ARM SoCs
i2c: altera: use ARCH_INTEL_SOCFPGA also for 32-bit ARM SoCs
fpga: altera: use ARCH_INTEL_SOCFPGA also for 32-bit ARM SoCs
dmaengine: socfpga: use ARCH_INTEL_SOCFPGA also for 32-bit ARM SoCs
clk: socfpga: use ARCH_INTEL_SOCFPGA also for 32-bit ARM SoCs (and compile test)
clk: socfpga: allow compile testing of Stratix 10 / Agilex clocks
arm64: socfpga: merge Agilex and N5X into ARCH_INTEL_SOCFPGA
EDAC: altera: merge ARCH_SOCFPGA and ARCH_STRATIX10
clk: socfpga: merge ARCH_SOCFPGA and ARCH_STRATIX10
clk: socfpga: build together Stratix 10, Agilex and N5X clock drivers
net: stmmac: merge ARCH_SOCFPGA and ARCH_STRATIX10
mfd: altera: merge ARCH_SOCFPGA and ARCH_STRATIX10
ARM: socfpga: introduce common ARCH_INTEL_SOCFPGA
clk: socfpga: allow building N5X clocks with ARCH_N5X
Link: https://lore.kernel.org/r/20210330110430.558182-1-dinguyen@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Port the scmi reset driver to the new SCMI reset interface based on
protocol handles and common devm_get_ops().
Link: https://lore.kernel.org/r/20210316124903.35011-22-cristian.marussi@arm.com
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
ARCH_SOCFPGA is being renamed to ARCH_INTEL_SOCFPGA so adjust the
32-bit ARM drivers to rely on new symbol.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Agilex, N5X and Stratix 10 share all quite similar arm64 hard cores and
SoC-part. Up to a point that N5X uses the same DTSI as Agilex. From
the Linux kernel point of view these are flavors of the same
architecture so there is no need for three top-level arm64
architectures. Simplify this by merging all three architectures into
ARCH_INTEL_SOCFPGA and dropping the other ARCH* arm64 Kconfig entries.
The side effect is that the INTEL_STRATIX10_SERVICE will now be
available for both 32-bit and 64-bit Intel SoCFPGA, even though it is
used only for 64-bit.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Use devm_rpi_firmware_get() so as to make sure we release RPi's firmware
interface when unbinding the device.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Follow the clock and regulator subsystems' lead and add a bulk API
for reset controls.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210314154459.15375-5-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
I have a handful of new RISC-V related patches for this merge window:
* A check to ensure drivers are properly using uaccess. This isn't
manifesting with any of the drivers I'm currently using, but may catch
errors in new drivers.
* Some preliminary support for the FU740, along with the HiFive
Unleashed it will appear on.
* NUMA support for RISC-V, which involves making the arm64 code generic.
* Support for kasan on the vmalloc region.
* A handful of new drivers for the Kendryte K210, along with the DT
plumbing required to boot on a handful of K210-based boards.
* Support for allocating ASIDs.
* Preliminary support for kernels larger than 128MiB.
* Various other improvements to our KASAN support, including the
utilization of huge pages when allocating the KASAN regions.
We may have already found a bug with the KASAN_VMALLOC code, but it's
passing my tests. There's a fix in the works, but that will probably
miss the merge window.
-----BEGIN PGP SIGNATURE-----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=CutX
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.12-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
"A handful of new RISC-V related patches for this merge window:
- A check to ensure drivers are properly using uaccess. This isn't
manifesting with any of the drivers I'm currently using, but may
catch errors in new drivers.
- Some preliminary support for the FU740, along with the HiFive
Unleashed it will appear on.
- NUMA support for RISC-V, which involves making the arm64 code
generic.
- Support for kasan on the vmalloc region.
- A handful of new drivers for the Kendryte K210, along with the DT
plumbing required to boot on a handful of K210-based boards.
- Support for allocating ASIDs.
- Preliminary support for kernels larger than 128MiB.
- Various other improvements to our KASAN support, including the
utilization of huge pages when allocating the KASAN regions.
We may have already found a bug with the KASAN_VMALLOC code, but it's
passing my tests. There's a fix in the works, but that will probably
miss the merge window.
* tag 'riscv-for-linus-5.12-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (75 commits)
riscv: Improve kasan population by using hugepages when possible
riscv: Improve kasan population function
riscv: Use KASAN_SHADOW_INIT define for kasan memory initialization
riscv: Improve kasan definitions
riscv: Get rid of MAX_EARLY_MAPPING_SIZE
soc: canaan: Sort the Makefile alphabetically
riscv: Disable KSAN_SANITIZE for vDSO
riscv: Remove unnecessary declaration
riscv: Add Canaan Kendryte K210 SD card defconfig
riscv: Update Canaan Kendryte K210 defconfig
riscv: Add Kendryte KD233 board device tree
riscv: Add SiPeed MAIXDUINO board device tree
riscv: Add SiPeed MAIX GO board device tree
riscv: Add SiPeed MAIX DOCK board device tree
riscv: Add SiPeed MAIX BiT board device tree
riscv: Update Canaan Kendryte K210 device tree
dt-bindings: add resets property to dw-apb-timer
dt-bindings: fix sifive gpio properties
dt-bindings: update sifive uart compatible string
dt-bindings: update sifive clint compatible string
...
Updates for SoC specific drivers include a few subsystems that
have their own maintainers but send them through the soc tree:
SCMI firmware:
- add support for a completion interrupt
Reset controllers:
- new driver for BCM4908
- new devm_reset_control_get_optional_exclusive_released()
function
Memory controllers:
- Renesas RZ/G2 support
- Tegra124 interconnect support
- Allow more drivers to be loadable modules
TEE/optee firmware:
- minor code cleanup
The other half of this is SoC specific drivers that do not
belong into any other subsystem, most of them living in
drivers/soc:
- Allwinner/sunxi power management work
- Allwinner H616 support
- ASpeed AST2600 system identification support
- AT91 SAMA7G5 SoC ID driver
- AT91 SoC driver cleanups
- Broadcom BCM4908 power management bus support
- Marvell mbus cleanups
- Mediatek MT8167 power domain support
- Qualcomm socinfo driver support for PMIC
- Qualcomm SoC identification for many more products
- TI Keystone driver cleanups for PRUSS and elsewhere
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=I2Zn
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Updates for SoC specific drivers include a few subsystems that have
their own maintainers but send them through the soc tree:
SCMI firmware:
- add support for a completion interrupt
Reset controllers:
- new driver for BCM4908
- new devm_reset_control_get_optional_exclusive_released() function
Memory controllers:
- Renesas RZ/G2 support
- Tegra124 interconnect support
- Allow more drivers to be loadable modules
TEE/optee firmware:
- minor code cleanup
The other half of this is SoC specific drivers that do not belong into
any other subsystem, most of them living in drivers/soc:
- Allwinner/sunxi power management work
- Allwinner H616 support
- ASpeed AST2600 system identification support
- AT91 SAMA7G5 SoC ID driver
- AT91 SoC driver cleanups
- Broadcom BCM4908 power management bus support
- Marvell mbus cleanups
- Mediatek MT8167 power domain support
- Qualcomm socinfo driver support for PMIC
- Qualcomm SoC identification for many more products
- TI Keystone driver cleanups for PRUSS and elsewhere"
* tag 'arm-drivers-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (89 commits)
soc: aspeed: socinfo: Add new systems
soc: aspeed: snoop: Add clock control logic
memory: tegra186-emc: Replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE
memory: samsung: exynos5422-dmc: Correct function names in kerneldoc
memory: ti-emif-pm: Drop of_match_ptr from of_device_id table
optee: simplify i2c access
drivers: soc: atmel: fix type for same7
tee: optee: remove need_resched() before cond_resched()
soc: qcom: ocmem: don't return NULL in of_get_ocmem
optee: sync OP-TEE headers
tee: optee: fix 'physical' typos
drivers: optee: use flexible-array member instead of zero-length array
tee: fix some comment typos in header files
soc: ti: k3-ringacc: Use of_device_get_match_data()
soc: ti: pruss: Refactor the CFG sub-module init
soc: mediatek: pm-domains: Don't print an error if child domain is deferred
soc: mediatek: pm-domains: Add domain regulator supply
dt-bindings: power: Add domain regulator supply
soc: mediatek: cmdq: Remove cmdq_pkt_flush()
soc: mediatek: pm-domains: Add support for mt8167
...
The ZTE ZX set-top-box SoC platform was added in 2015 by Jun Nie, with
Baoyou Xie and Shawn Guo subsequently becoming maintainers after the
addition of the 64-bit variant.
However, the only machines that were ever supported upstream are the
reference designs, not actual set-top-box devices that would benefit
from this support. All ZTE set-top-boxes from the past few years seem
to be based on third-party SoCs. While there is very little information
about zx296702 and zx296718 on the web, I found some references to other
chips from the same family, such as zx296716 and zx296719, which were
never submitted for upstream support. Finally, there is no support for
the GPU on either of them, with the lima and panfrost device drivers
having been added after work on the zx platform had stopped.
Shawn confirmed that he has not seen any interest in this platform for
the past four years, and that it can be removed.
Thanks to Jun and Shawn for maintaining this platform over the past
five years.
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add a reset controller driver for the Canaan Kendryte K210 SoC. This
driver relies on its syscon compatible parent node (sysctl) for its
register mapping. Default this driver compilation to y when the
SOC_CANAAN option is selected.
The MAINTAINERS file is updated, adding the entry "CANAAN/KENDRYTE K210
SOC RESET CONTROLLER DRIVER" with myself listed as maintainer for this
driver.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
A function has a different name between their prototype
and its kernel-doc markup:
../drivers/reset/core.c:888: warning: expecting prototype for device_reset(). Prototype was for __device_reset() instead
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Linus Torvalds