qla4_82xx_rom_lock() spins on a certain hardware state until it is
updated. At the end of each spin, if in_interrupt() is true, it does 20
loops of cpu_relax(). Otherwise, it yields the CPU.
While in_interrupt() is ill-defined and does not provide what the name
suggests, it is not needed here: qla4_82xx_rom_lock() is always called
from process context. Below is an analysis of its callers:
- ql4_nx.c: qla4_82xx_rom_fast_read(), all process context callers:
=> ql4_nx.c: qla4_82xx_pinit_from_rom(), GFP_KERNEL allocation
=> ql4_nx.c: qla4_82xx_load_from_flash(), msleep() in a loop
- ql4_nx.c: qla4_82xx_pinit_from_rom(), earlier discussed
- ql4_nx.c: qla4_82xx_rom_lock_recovery(), bound to "isp_operations"
->rom_lock_recovery() hook, which has one process context caller,
qla4_8xxx_device_bootstrap(), with callers:
=> ql4_83xx.c: qla4_83xx_need_reset_handler(), process, msleep()
=> ql4_nx.c: qla4_8xxx_device_state_handler(), multiple msleep()s
- ql4_nx.c: qla4_82xx_read_flash_data(), has cond_resched()
Remove the in_interrupt() check. Mark, qla4_82xx_rom_lock(), and the
->rom_lock_recovery() hook, with "Context: task, can sleep".
Change qla4_82xx_rom_lock() implementation to sleep 20ms, instead of a
schedule(), for each spin. This is more deterministic, and it matches
the other implementations bound to ->rom_lock_recovery().
Link: https://lore.kernel.org/r/20201126132952.2287996-9-bigeasy@linutronix.de
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Manish Rangankar <mrangankar@marvell.com>
Cc: <GR-QLogic-Storage-Upstream@marvell.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qla4_82xx_idc_lock() spins on a certain hardware state until it is
updated. At the end of each spin, if in_interrupt() is true, it does 20
loops of cpu_relax(). Otherwise, it yields the CPU.
While in_interrupt() is ill-defined and does not provide what the name
suggests, it is not needed here: qla4_82xx_idc_lock() is always called from
process context. Below is an analysis of its callers:
- ql4_nx.c: qla4_82xx_need_reset_handler(), 1-second msleep() in a
loop.
- ql4_nx.c: qla4_82xx_isp_reset(), calls
qla4_8xxx_device_state_handler(), which has multiple msleep()s.
Beside direct calls, qla4_82xx_idc_lock() is also bound to isp_operations
->idc_lock() hook. Other functions which are bound to the same hook,
e.g. qla4_83xx_drv_lock(), also have an msleep(). For completeness, below
is an analysis of all callers of that hook:
- ql4_83xx.c: qla4_83xx_need_reset_handler(), has an msleep()
- ql4_83xx.c: qla4_83xx_isp_reset(), calls
qla4_8xxx_device_state_handler(), which has multiple msleep()s.
- ql4_83xx.c: qla4_83xx_disable_pause(), all process context callers:
=> ql4_mbx.c: qla4xxx_mailbox_command(), msleep(), mutex_lock()
=> ql4_os.c: qla4xxx_recover_adapter(), schedule_timeout() in loop
=> ql4_os.c: qla4xxx_do_dpc(), workqueue context
- ql4_attr.c: qla4_8xxx_sysfs_write_fw_dump(), sysfs bin_attribute
->write() hook, process context
- ql4_mbx.c: qla4xxx_mailbox_command(), earlier discussed
- ql4_nx.c: qla4_8xxx_device_bootstrap(), callers:
=> ql4_83xx.c: qla4_83xx_need_reset_handler(), process, msleep()
=> ql4_nx.c: qla4_8xxx_device_state_handler(), earlier discussed
- ql4_nx.c: qla4_8xxx_need_qsnt_handler(), callers:
=> ql4_nx.c: qla4_8xxx_device_state_handler(), multiple msleep()s
=> ql4_os.c: qla4xxx_do_dpc(), workqueue context
- ql4_nx.c: qla4_8xxx_update_idc_reg(), callers:
=> ql4_nx.c: qla4_8xxx_device_state_handler(), earlier discussed
=> ql4_os.c: qla4_8xxx_error_recovery(), only called by
qla4xxx_pci_slot_reset(), which is bound to PCI ->slot_reset()
process-context hook
- ql4_nx.c: qla4_8xxx_device_state_handler(), earlier discussed
- ql4_os.c: qla4xxx_recover_adapter(), earlier discussed
- ql4_os.c: qla4xxx_do_dpc(), earlier discussed
Remove the in_interrupt() check. Mark, qla4_82xx_idc_lock(), and the
->idc_lock() hook itself, with "Context: task, can sleep".
Change qla4_82xx_idc_lock() implementation to sleep 100ms, instead of a
schedule(), for each spin. This is more deterministic, and it matches other
PCI HW locking functions in the driver.
Link: https://lore.kernel.org/r/20201126132952.2287996-8-bigeasy@linutronix.de
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Manish Rangankar <mrangankar@marvell.com>
Cc: <GR-QLogic-Storage-Upstream@marvell.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
All files in this driver directory contain the following notice:
See LICENSE.qla4xxx for copyright and licensing details.
LICENSE.qla4xxx can be found in Documentation/scsi/. The file contains:
- A copyright notice
This copyright notice is redundant as all files contain the same
copyright notice already
- A license notice
You may modify and redistribute the device driver code under the
GNU General Public License (a copy of which is attached hereto as
Exhibit A) published by the Free Software Foundation (version 2).
- The full GPLv2 license text
This can be replaced with the corresponding SPDX license identifier
(GPL-2.0-only) in the source files which reference this license
file.
- The full GPLv2 license text
A redundant copy of LICENSES/preferred/GPL-2.0
Remove the notices and add the SPDX license identifier GPL-2.0-only to the
source files.
Finally remove the now redundant LICENSE.qla4xxx file.
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A system crashes when continuously removing/re-adding the storage
controller.
Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Spotted while preparing qla2xxx changes as the symbols exist in both
drivers (sigh..).
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
And simplify the MSI-X logic in general - just request the two vectors
directly instead of going through an indirection table.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Nilesh Javali <nilesh.javali@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
vmalloc.h used to be included from include/net/inet_hashtables.h
but it is no longer the case.
Fixes: 095dc8e0c3 ("tcp: fix/cleanup inet_ehash_locks_alloc()")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Eric Dumazet <edumzet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issue:
modprobe qla4xxx is killed by systemd due to timeout.
Solution:
The exporting of sysfs DDBs from qla4xxx_probe_adapter added delay of
approximately 15s due to which system-udevd killed the modprobe of the
driver. Added fix to export the sysfs DDBs from the DPC handler.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Issue:
minidump data collection fails as driver reports data mismatch
Fix:
When the driver encounters a new entry type that it cannot process,
it should just skip the entry and adjust the total buffer size by
subtracting the skipped bytes from it. This is to ensure that there
is no data mismatch because of the new entries.
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
Pending IO wait does not complete after triggering Graceful reset,
causing ack timeout and call traces.
Fix:
1. Reducing the IO command wait timeout before triggering reset,
as logically also timeout should be less than reset timeout (10sec).
2. Moving the abort IO after chip reset, because only after
chip reset, driver owns the IO otherwise it is with firmware and can
still revert back with response.
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
qla4xxx Unable to clear DDB indices when logout fails due to
failure of connection close mbox command.
Root cause:
If login to session fail, iscsiadm make call to destroy_session.
qla4xxx driver does not free ddb index map before free_ddb()
Fix:
Clear DDB Index map before free_ddb in "destroy_session"
in case of connection close mailbox command failure with 4005h.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Removed AF_83XX_NO_FWDUMP flag and directly checking IDC_CTRL bit1
while taking minidump, to check for graceful reset.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added support for Diagnostics MBOX command via BSG Vendor HST_VENDOR
interface. This command provides various tests for validating hardware
functionality.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Earlier logic for driver created iscsi_session->discovery_parent_idx
was to store ram index of a sendtarget entry, but driver frees
sendtarget ram index as soon as firmware is done with discovery,
which is available for further use. So changing the logic to point
iscsi_session->discovery_parent_idx to store sendtarget flashnode index.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
While loopback diagnostic is in progress, disable the ACB which resets
all the active connections to target. Disable ACB would filter out all
the DHCP multicast and broadcast packets which otherwise cause the
diagnostic test to take longer time to complete or failures in some
other cases.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If logout is performed on a failed session entry then that session
should be gracefully removed.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch allows iscsiadm to manage iSCSI target information stored on
qla4xxx adapter flash on per host basis.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Boot from SAN fails in some cases where boot target login response
is slow. In this case, probe finishes early and triggers init, which
doesn't find remote disk to mount root which leads to BFS failure.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Problem:
QLA4xxx firmware may assert if given more IOCBs than it can handle.
Solution:
The driver was updated to throttle the number of active IOCBs based
on the total number of IOCB buffers received from get_firmware_status
mbx_sts[2].
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Quiesce all different activities performed by driver upon the link events
while loopback diagnostics is in progress.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
Mailbox command timed out after switching from polling mode to interrupt mode.
Events:-
1. Mailbox interrupts are disabled
2. FW generates AEN and at same time driver enables Mailbox Interrupt
3. Driver issues new mailbox to Firmware
In above case driver will not get AEN interrupts generated by FW in step #2 as
FW generated this AEN when interrupts are disabled. During the same time
driver enabled the mailbox interrupt, so driver will not poll for interrupt.
Driver will never process AENs generated in step #2 and issues new mailbox to
FW, but now FW is not able to post mailbox completion as AENs generated before
are not processed by driver.
Fix:
Enable Mailbox / AEN interrupts before initializing FW in case of ISP83XX.
This will make sure we process all Mailbox and AENs in interrupt mode.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In qla4xxx_ep_connect(), qla_ep->dst_addr and dst_addr are type
struct sockaddr. We are copying sizeof(struct sockaddr_in6) bytes
from dst_addr to qla_ep->dst_addr which is 12 bytes larger. This
will cause memory corruption. So we change qla_ep->dst_addr to
struct sockaddr_storage which is of 128 byte, large enough to
hold sizeof(struct sockaddr_in6).
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added support to capture dump (Minidump) which allows us to
catpure a snapshot of the firmware/hardware states at the time
of firmware failure
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch will allow iscsiadm to create multiple session
for the same target on per host.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For offload iSCSI like qla4xxx CHAP entries are stored in FLASH.
This patch adds support to list CHAP entries stored in FLASH and
delete specified CHAP entry from FLASH using iscsi tools.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added ping support for network connection diagnostics.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added support to post kernel host event to application using
netlink interface.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added debug print with error code in case of firmware error.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During watchdog, need to monitor temperature of ISP82XX core
and set device state to FAILED when temperature reaches
"Panic" level.
Signed-off-by: Mike Hernandez <michael.hernandez@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Check for firmware alive and do premature completion of
mbox commands in case of FW hung before doing chip_reset
Signed-off-by: Shyam Sunder <shyam.sunder@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
With open-iscsi support, target entries persisted in the FLASH were not
login. Added support in the qla4xxx driver to do the login on probe
time to the target entries saved in the FLASH by user.
With this changes upgrade to the new kernel with open-iscsi support in
qla4xxx will ensure users original target entries login on driver load
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When sendtargets response is greater then max receive data segment length,
the passthrough IOCB failed with data overrun status. Solution is to
allocate space for iSCSI header in the IOCB response buffer.
JIRA Key: UPSISCSI-147
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
QLogic applications store the CHAP information in FLASH. During login,
authentication information is provided using an index into the CHAP region.
In order to support QLogic applications along with iscsiadm, updated the
LLD to not add duplicate CHAP entries in the CHAP region and preserve the
existing CHAP info in the CHAP region in FLASH.
This allows QLogic applications to pre-write the CHAP entries in the
CHAP region.
With iscsiadm, when the CHAP authentication information is sent to the LLD, the
LLD searches for the entry in CHAP region in FLASH, if exists then do not add.
If CHAP entry does not exist then add the CHAP entry in the CHAP region.
JIRA Key: UPSISCSI-146
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Driver was not setting the bidirectional CHAP bit correctly in
the DDB entry.
JIRA Key: UPSISCSI-108
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Ahmed S. Darwish