Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Change enic driver description to "Cisco VIC Ethernet NIC Driver"
2) Fix tab space
3) Update MAINTAINERS list
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware does not honor vlan filters from the host and so the driver does
not need to advertise this.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces dev->mc_count in all drivers (hopefully I didn't miss
anything). Used spatch and did small tweaks and conding style changes when
it was suitable.
Jirka
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEFINE_PCI_DEVICE_TABLE() so we get place PCI ids table into correct section
in every case.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some misc changes to cleanup whitespace issues and fix/remove some #define
HW defintions.
1) fix some whitespace issues
2) more verbose err msg when resources aren't available to configure vnic
3) remove unused #define
4) fix RSS #define rss hash types
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only rx_usec and tx_usec options for ethtool -C are settable as those
are the only settings that make sense to HW. Adds driver reporting of
intr coalescing timer value in usec units rather than HW units.
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In set_multicast(), only push pkt filter changes down to firmware if
pkt filter actually changes.
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During dev->open(), make sure we get at least one skb on the Rx ring.
Otherwise abort the interface load. Also, if we get skb allocation
failures in NAPI poll while trying to replenish the ring, try again
later so we don't end up starving out the Rx ring completely.
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix dev->stop shutdown bug where driver was stopping xmit queue and then
disabling intrs. Fix is to disable intrs first and then stop the xmit
queue, otherwise an interrupt could cause the queue to be rewoken. Also,
no need to explicitly do queue servicing because queues are cleaned and
reset back to initial state at end of dev->stop. Servicing queues also
had the side-effect of also rewakening the xmit queue, which is not what
we want.
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To unclutter probe() a little bit, put all device initialization code
in one spot and device deinit code in another spot. Also remove unused
rq->buf_index variable/func.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nic firmware can return zero for port MTU, so check for non-zero value
before checking for change in port MTU.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provision for multiple Rx/Tx queues. Max of 8 WQs and 8 RQs. Max for
completion queue is 8+8=16 and max for interrupt resources is 8+8+2.
Add driver/firmware interface for setting up RSS secret key and indirection
table.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug fix: included MAC drops in rx_dropped netstat. Also track Rx trunctations
stat at the MAC
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some driver -> nic firmware calls weren't guarded with a spinlock, exposing
the call i/f to a race between two threads
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enic WQ desc supports a maximum 16K buf size, so split any send fragments
larger than 16K into several descs.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A0 revision ASIC has an erratum on the RQ desc cache on chip where the
cache can become corrupted causing pkt buf writes to wrong locations. The s/w
workaround is to post a dummy RQ desc in the ring every 32 descs, causing a
flush of the cache. A0 parts are not production, but there are enough of
these parts in the wild in test setups to warrant including workaround. A1
revision ASIC parts fix erratum.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nic firmware can place resources (queues, intrs, etc) on multiple BARs, so
allow driver to discover/map resources beyond BAR0.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to put ethtool_ops in data, they should be const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a couple of cases collapse some extra code like:
int retval = NETDEV_TX_OK;
...
return retval;
into
return NETDEV_TX_OK;
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Followup of commits 9d21493b4b
and 08baf56108
(net: tx scalability works : trans_start)
(net: txq_trans_update() helper)
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Multi queue drivers can
avoid one cache miss (on dev->trans_start) in their start_xmit()
handler.
Exceptions are NETIF_F_LLTX drivers (vxge & tehuti)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_40BIT_MASK macro with DMA_BIT_MASK(40)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tx_timeout reset path needs to re-init dev and re-apply nic cfg to
enable vlan stripping.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report all bad FCS errs as frames errs. This includes frames with bad
FCS on wire detected by MAC and frames which may be truncated due to
ingress FIFO overruns. No longer print a driver msg on bad FCS err.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return notify intr credits after notify intr from firmware. This is
especially important for legacy PCI intr mode, where not returning
credits would cause PBA to remain asserted which would get us right
back into the ISR.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers lost the ability to set ethernet address accidently
during the net_device_ops conversion.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable ethtool support for get/set_flags so LRO can be turned on/off
by fwding drivers such as the bridge driver. LRO is not compatible
with fwding drivers.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.
Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert this driver to network device ops. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Drivers need not do it any more.
Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: David S. Miller <davem@davemloft.net>
2.6.27-git2 kernel build fails with allyesconfig on powerpc with
build error
<introduced by commit 01f2e4ead2c51226ed1283ef6a8388ca6f4cff8f>
CC drivers/net/enic/enic_main.o
drivers/net/enic/enic_main.c: In function âenic_queue_wq_skb_tsoâ:
drivers/net/enic/enic_main.c:576: error: implicit declaration of function âcsum_ipv6_magicâ
make[3]: *** [drivers/net/enic/enic_main.o] Error 1
<introduced by commit c4e84bde1d595d857d3c74b49b9c45cc770df792>
drivers/net/qlge/qlge_main.c: In function âql_tsoâ:
drivers/net/qlge/qlge_main.c:1862: error: implicit declaration of function âcsum_ipv6_magicâ
make[3]: *** [drivers/net/qlge/qlge_main.o] Error 1
<introduced by commit 95252236e73e789dd186ce796a2abc60b3a61ebe>
drivers/net/jme.c: In function âjme_tx_tsoâ:
drivers/net/jme.c:1784: error: implicit declaration of function âcsum_ipv6_magicâ
make[2]: *** [drivers/net/jme.o] Error 1
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug fix: don't set netdev->name early before netdev registration. Setting
netdev->name early with dev_alloc_name() would occasionally cause netdev
registration to fail returning error that device was already registered.
Since we're using netdev->name to name MSI-X vectors, we now need to
move the request_irq after netdev registartion, so move it to ->open.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bug fix: Free MSI intr with correct data handle
Use davem proposed naming for MSI-X tx/rx vectors (ethX-tx-0, ethX-rx-0)
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fixes for review items from Ben Hutchings:
- use netdev->net_stats rather than private net_stats
- use ethtool op .get_sset_count rather than .get_stats_count
- err out if setting Tx/Rx csum or TSO using ethtool and setting is
not enabled for device.
- pass in jiffies + constant to round_jiffies
- return err if new MTU is out-of-bounds
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
LRO is only applied to IPv4 pkts, so don't use the LRO indication functions
for anything other IPv4 pkts. Every non-IPv4 pkt is indicated using non-
LRO functions.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>