So far be2net has been using BE3 in legacy mode. It now checks for native
mode capability and if available it sets it. In native mode, the RX_COMPL
structure is different from that in legacy mode.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lancer requires multicast capability flag set during IFACE_CREATE
for adding multicast filters.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Subramanian Seetharaman <subbu.seetharaman@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use hba_port_num for phy loopback and ethtool phy identification.
From: Suresh R <suresh.reddy@emulex.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to display temperature of ASIC via ethtool -S
From: Somnath K <somnath.kotur@emulex.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With transparent VLAN tagging, the ASIC wrongly indicates packets with VLAN ID.
Strip them off in the driver. The VLAN Tag to be stripped will be given to the host
as an async message.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New counters:
> jabber frame stats
> red drop stats
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be_cmd_pmac_add/del functions need to pass domain number to the firmware.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Key changes are:
- EQ ids are not assigned consecutively in Lancer. So, fix mapping of MSIx
vector to EQ-id.
- BAR mapping and some req locations different for Lancer.
- TCP,UDP,IP checksum fields must be compulsorily set in TX wrb for TSO in
Lancer.
- CEV_IST reg not present in Lancer; so, peek into event queue to check for
new entries
- cq_create and mcc_create cmd interface is different for Lancer; handle
accordingly
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following code and data are defined but never used in current
driver.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to use one of the priority codes allowed by CNA f/w for NIC traffic
from host. The driver gets the bit map of the priority codes allowed for
host traffic through a asynchronous message from the f/w that the driver
subscribes to.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds multiple RX queue support to be2net. There are
upto 4 extra rx-queues per port into which TCP/UDP traffic can be hashed into.
Some of the ethtool stats are now displayed on a per queue basis.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ONLINE registers can return 0xFFFFFFFF on more than one
occassion. On systems that care, reading these registers could
lead to problems.
So the new code decides that the ASIC has encountered and error
by reading the UE_STATUS_LOW/HIGH registers. AND them with
the mask values and a non-zero result indicates an error.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when the BE device becomes unresponsive, dump the registers to help debugging
Signed-off-by: Somnath K <somnathk@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes names of some variables.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be2net driver is currently not showing correct phy details in certain cases.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Patch adds support to enable PCI SRIOV in the driver and changes to handle initialization of PCI virtual functions.
- Function handler to change mac addresses for VF from its corresponding PF.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tx/mcc polling, napi_complete() is being incorrectly called
before reaping tx completions. This can cause tx compl processing
to be scheduled on another cpu concurrently which can result in a panic.
This if fixed by calling napi complete() after tx/mcc compl processing
but before re-enabling interrupts (via a cq notify).
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an MCC cmd is issued (via a netdev/ethtool op)
while the device is not open, the MCC CQ gets processed but the EQ
is not processed (as isr is not registered.) This can cause the EQ
to become full. So, while the device is not open, CQ must not be re-armed
to prevent EQ entries.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now flashing both BE2 and BE3 devices is supported.
From: Naresh G <nareshg@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug fix in be2net for newer generation of BladeEngine ASIC.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch implements a firmware command to fetch the eeprom data.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIC controller has to be set to an appropriate mode before doing a loopback
test. Test will fail otherwise.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for ethtool selftest.
From: Suresh R <sureshr@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for WOL using Magic Packet after suspend is done.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These cmds are issued to the fw in probe/resume and remove/suspend
paths to help fw execute some initialization and cleanup code.
This change needed the be_hw_up() code to be refactored as be_get_config().
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To send upto 64 addresses in the multicast-set cmd, the non-embeeded cmd format
that provides for a bigger buffer is used instead of an embedded format.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Please apply patch to update redboot section while firmware update. Code
checks if section needs to be updated before actually doing it.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/cdc_ether.c
All CDC ethernet devices of type USB_CLASS_COMM need to use
'&mbm_info'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Update ethtool get_settings function to:
- get current link speed settings from controller
- get port transceiver type from controller
- fill appropriate values for supported, phy_address
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MCC_STATUS_NOT_SUPPORTED should be decimal 66 not hex 66.
This patch fixes this typo. Patch against net-2.6 tree.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vtp bit in RX completion descriptor could be wrongly set in
some skews of BladEngine. Ignore this bit if vtm is not set.
Resending because the previous patch was against net-next tree.
This patch is against the net-2.6 tree.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All cmds issued to BE after the creation of mccq must now use the mcc-q
(and not mbox) to avoid a hw issue that results in mbox poll timeout.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to support flashing of the be2 network adapter using the
request_firmware() & ethtool infrastructure. The trigger to flash the device
will come from ethtool utility. The driver will invoke request_firmware()
to start the flash process. The file containing the flash image is expected
to be available in /lib/firmware/
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a bug fix to avoid system going into a bad state when
driver is loaded in context of kdump kernel. The patch fixes the issue
by performing a soft reset of pci function at probe time.
Signed-off-by: sarveshwarb <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be_mbox_db_ring() has been changed to be_mbox_notify() (to be consistent with
be_mcc_notify()) and struct be_mcc_cq_entry changed to be_mcc_compl
to be consistent with rx/tx_compl.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde