The host makes direct calls into phy using ufs_qcom_phy_*()
APIs. These APIs are only defined for 20nm qcom-ufs-qmp phy
which is not being used by any architecture as yet. Future
architectures too are not going to use 20nm ufs phy.
So remove these ufs_qcom_phy_*() calls from host to let further
change declare the 20nm phy as broken.
Also remove couple of stale enum defines for ufs phy.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use actual bit position instead of UFS_BIT() macro. This patch also
changes bit-17 to meaningful #define.
This change is as per discussion here [1]
[1] -> https://lkml.org/lkml/2017/8/28/786
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change testbus default config, dump additional testbus registers along
with other debug vendor specific registers. These additional info are
useful in debugging link related failures.
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The maximum value PA_SaveConfigTime is 250 (10us) but this is not enough
for some vendors. Gear switch from PWM to HS may fail even with this
max. PA_SaveConfigTime. Gear switch can be issued by host controller as
an error recovery and any software delay will not help on this case so
we need to increase PA_SaveConfigTime to >32us as per vendor
recommendation. This change adds a quirk to increase the
PA_SaveConfigTime parameter.
Reviewed-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This change adds printouts of testbus and debug registers.
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
New revisions of UFS host controller supports the new UniPro
hardware controller (referred as QUniPro). This patch adds
the support to enable this new UniPro controller hardware.
This change also adds power optimization for bus scaling feature,
as well as support for HS-G3 power mode.
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adds support for configuring and reading the test bus and debug
registers. This change also adds another vops in order to print the
debug registers.
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some implementation of UFS host controller HW might have some non-standard
behaviours (quirks) when compared to behaviour specified by UFSHCI
specification. This patch add support to allow specifying all such quirks
to standard UFS host controller driver so standard driver takes them into
account.
In this change a UFSHCD_QUIRK_DELAY_BEFORE_DME_CMDS is introduced,
where a minimum delay of 1ms is required before DME commands for
stability purposes.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Sometimes, specific information about the UFS controller revision is
required in order to determine certain operations or execute
controller dependent quirks.
In order to avoid reading the controller revision multiple times,
we simply read it once and save this information in internal structure.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This change adds support for Qualcomm Technologies Inc platforms that
use UFS driver. for example, it adds :
- PM specific operations during hibern8, suspend, resume, clock setup
- qcom-ufs generic phy driver initialization, calibration,
power-on/off sequence, etc.
- UFS Controller specific configuration
- Rate, Gear, Mode negotiation between device and controller
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Dov Levenglick <dovl@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Vivek Gautam