The tlv320aic31xx driver relies on regcache_sync() to restore the register
contents after going to _BIAS_OFF, for example during system suspend. This
does not work for the jack detection configuration since that is configured
via the same register that status is read back from so the register is
volatile and not cached. This can also cause issues during init if the jack
detection ends up getting set up before the CODEC is initially brought out
of _BIAS_OFF, we will reset the CODEC and resync the cache as part of that
process.
Fix this by explicitly reapplying the jack detection configuration after
resyncing the register cache during power on.
This issue was found by an engineer working off-list on a product
kernel, I just wrote up the upstream fix.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210723180200.25105-1-broonie@kernel.org
Cc: stable@vger.kernel.org
Currently the tlv320aic31xx driver has regulator support but does not
enable the regulators during probe, deferring this until something causes
ASoC to make the card active. It does put the device into cache only mode
but only when the component level probe is called, however if interrupts
are in use the driver will access the regmap before then which if the
regulators are not powered on would cause I/O problems.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210707160234.16253-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200719153822.59788-1-grandmaster@al2klimov.de
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_digital_mute() is internally using both
mute_stream() (1) or digital_mute() (2), but the difference between
these 2 are only handling direction.
We can merge digital_mute() into mute_stream
int snd_soc_dai_digital_mute(xxx, int direction)
{
...
else if (dai->driver->ops->mute_stream)
(1) return dai->driver->ops->mute_stream(xxx, direction);
else if (direction == SNDRV_PCM_STREAM_PLAYBACK &&
dai->driver->ops->digital_mute)
(2) return dai->driver->ops->digital_mute(xxx);
...
}
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/874kqhxxhz.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Chip supports soft stepping of volume changes and it is enabled by
default.
This patch adds a control for it, so it could be either made slower
(two sample periods per step instead of one), or disabled.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Link: https://lore.kernel.org/r/20191129132719.11603-1-nikita.yoush@cogentembedded.com
Signed-off-by: Mark Brown <broonie@kernel.org>
HP output driver has two parameters that can be configured to reduce
pop noise: power-on delay and ramp-up step time. Two new kcontrols
have been added to set these parameters.
Also have to alter timeout in aic31xx_dapm_power_event() because default
timeout does fire when higher supported power-on delay are configured.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Link: https://lore.kernel.org/r/20191128135447.26458-1-nikita.yoush@cogentembedded.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The tlv320aic31xx devices allow to adjust the output common-mode voltage
for best analog performance. The datasheet states that the common mode
voltage should be set to be <= AVDD/2.
This changes allows to configure the output common-mode voltage via a DT
property. If the property is absent the voltage is automatically chosen
as the highest voltage below/equal to AVDD/2.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20191118151207.28576-1-l.stach@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/tlv320aic31xx.c:261:29: warning:
cm_m_enum defined but not used [-Wunused-const-variable=]
It is never used, so can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190815091738.21680-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Both the supplies and reset GPIO might need a probe deferral for the
resource to be available. Don't print a error message in that case, as
it is a normal operating condition.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Andrew F. Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20190719143637.2018-1-l.stach@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This device can optionally detect headset or microphone button presses.
Add support for this by passing this event to the jack layer.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This device can detect the insertion/removal of headphones and headsets.
Enable reporting this status by enabling this interrupt and forwarding
this to upper-layers if a jack has been defined.
This jack definition and the resulting operation from a jack detection
event must currently be defined by sound card platform code until CODEC
outputs to jack mappings can be defined generically.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Regulator notifiers, that were registered during codec driver probing,
must be unregistered during driver release, or device managed versions
have to be used. This patch fixes codec drivers, that weren't explicitly
unregistering notifiers and simplifies those, that did that manually.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The return statement is indented too much by one level, fix this by
removing an extraneous tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Similar to short circuit detection, when the ADC/DAC is saturated and
overflows poor audio quality can result and should be reported to the
user. This device support Automatic Dynamic Range Compression (DRC)
to reduce this but it is not enabled currently in this driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These devices support detecting and reporting short circuits across
the output stages. Add support for reporting these issue. Do this
by registering an interrupt if available and enabling this error
to trigger that interrupt in the device.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With P0 R29, Bit2 set the I2S clocks will be running when the DAC/ADC is
powered down, but still the codec need to be powered up by needing at least
one complete DAPM path for the stream.
If the AIF is not needed (analog loopback for example) the I2S clocks will
not run as they are not needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Suggested-by: Stefan Müller-Klieser <s.mueller-klieser@phytec.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The audio interface is not really the DAC input. Use more generic name for
it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the reset state of the codec we do not have complete playback or capture
routes.
The audio playback/capture will not work due to missing clock signals on
the I2S bus if PLL, MDAC/NDAC/DAC MADC/NADC/ADC is powered down.
To make sure that even if all output/input is disconnected the codec is
generating clocks, we need to have valid DAPM route in every case to power
up the must needed parts of the codec.
I have verified that switching DAC (during playback) or ADC (during
capture) will stop the I2S clocks, so the only solution is to connect the
'Off' routes as well to output/input.
The routes will be only added if the codec is clock master. In case the
role changes runtime, the applied routes are removed.
Tested on am43x-epos-evm with aic3111 codec in master mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a reset function that toggles the reset line if available or uses
the software reset command otherwise. Use this in power up to ensure the
registers are in a sane state. This is useful when the driver module
is reloaded, or after Kexec, warm-reboots, etc..
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use fwnode_* API instead of of_*, the results are the same but
fwnode_* is cleaner and we get ACPI support.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use of gpiod_* needs <linux/gpio/consumer.h>, add this here.
Fixes: b6b247cd5e ("ASoC: tlv320aic31xx: Switch GPIO handling to use gpiod_* API")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently BCLK inverting is only handled when the DAI format is
DSP, but the BCLK may be inverted in any supported mode. Without
this using this CODEC in any other mode than DSP with the BCLK
inverted leads to bad sampling timing and very poor audio quality.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This CODEC supports being the WCLK and/or BCLK slave, add
support for this here.
Also make the alert into an error as alert is more urgent
than needed here and is rarely used.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If our set_sysclk DAI callback has not been called yet p_div will be 0
and dividing by this will cause an error. Print an error message and
leave before this.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move to using newer gpiod_* GPIO handling functions. This simplifies
the code and eases dropping platform data in the next patch. Also
remember GPIO are active low, so set "1" to reset.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function aic31xx_device_init() is only called from probe and
does nothing that logically shouldn't be in probe, remove this
unneeded function call and move its code into probe where it was called.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simple non-functional changes including:
* Fix spelling errors
* Reformat code for easier reading
* Remove unneeded code
* Remove assignments that are always overridden
* Normalize function return paths
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The return value is not checked, and even if it was there is nothing
we could do about it and messages are already printed.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix header copyright tags, while we are here, also switch to SPDX
and fixup MODULE tags to match.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The correct DT property for specifying a GPIO used for reset
is "reset-gpios", fix this here.
[Retitled for accuracy -- broonie]
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1195220
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare snd_soc_codec_driver structures as const as they are only passed
as an argument to the function snd_soc_register_codec. This argument is
of type const, so declare the structures with this property as const.
In file codecs/sn95031.c, snd_soc_codec_driver structure is also used in
a copy operation along with getting passed to snd_soc_register_codec.
So, it can be made const too.
Done using Coccinelle:
@match disable optional_qualifier@
identifier s;
position p;
@@
static struct snd_soc_codec_driver s@p={...};
@good1@
identifier match.s;
position p;
@@
snd_soc_register_codec(...,&s@p,...)
@bad@
identifier match.s;
position p!={match.p,good1.p};
@@
s@p
@depends on !bad disable optional_qualifier@
identifier match.s;
@@
static
+const
struct snd_soc_codec_driver s={...};
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAC3101 is mostly identical to DAC3100 with the exception that it has
stereo speaker AMP instead of mono used in DAC3100.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The compatible table was not updated when the support for DAC3100 was added.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This hardware supports only 2-channel DAI, even mono ADC digital output
has two channels with the same data.
Having min_channels=1 results in broken playback of mono files in setups
where CPU DAI supports mono.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
tlv320dac31xx is a subset of tlv320aic31xx:
- it does not have MIC inputs and ADC, thus capture is not supported,
- it has analog inputs AIN1/AIN2 that can be mixed into output.
Although tlv320dac31xx does work with tlv320aic31xx driver, this setup
does register non-existent widgets and non-existent capture stream.
Thus userspace lists non-existent objects in user interfaces, an can
access these, causing operations with device registers that are
declared as "reserved" in tlv320dac31xx datasheet.
This patch fixes this situation by separating controls/widgets/routes
into common, aic31xx-specific, and dac31xx-specific parts. Only parts
that match actual hardware (as declared in "compatible" device tree
property) are registered.
Changes from v1:
- update device tree binding documentation,
- rebased on top of "ASoC: codec duplicated callback function goes to
component on tlv320aic31xx" commit.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
codec driver and component driver has duplicated callback functions,
and codec side functions are just copied to component side when
register timing. This was quick-hack, but no longer needed.
This patch moves these functions from codec driver to component driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Lenovo 100S netbook has a codec controller for which there is a
driver, but doesn't know how to access the device. This adds the
necessary ACPI table for the driver to find the device.
Device (TTLV)
{
Name (_ADR, Zero) // _ADR: Address
Name (_HID, "10TI3100") // _HID: Hardware ID
Name (_CID, "10TI3100") // _CID: Compatible ID
Name (_DDN, "TI TLV320AIC3100 Codec Controller ") // _DDN: DOS Device Name
Name (_UID, One) // _UID: Unique ID
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Jan Schmidt <jan@centricular.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_dai_ops variables are not modified after initialization in
these drivers, so make them const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to
codec->dapm.bias_level with snd_soc_codec_get_bias_level() and replace all
other manual access to codec->dapm with snd_soc_codec_get_dapm().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
All drivers have the same line at the end of the set_bias_level callback to
update the bias_level state. Move this update into
snd_soc_dapm_force_bias_level() and remove them from the drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown