I2S always has two LRCLK phases and both CH1 and CH2 of the RX
must be enabled (corresponding to the low and high phases of LRCLK.)
The selection of the valid data channels is done by setting the DAC
CHA_SEL and CHB_SEL. CHA_SEL is always the first (left) channel,
CHB_SEL depends on the number of active channels.
Previously for mono ASP CH2 was not enabled, the result was playing
mono data would not produce any audio output.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 621d65f3b8 ("ASoC: cs42l42: Provide finer control on playback path")
Link: https://lore.kernel.org/r/20210805161111.10410-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The lowest valid SCLK corresponds to 44.1 kHz at 16-bit. Sample
rates less than this would produce SCLK below the minimum when using
a normal I2S frame. A constraint must be applied to prevent this.
The constraint is not applied if the machine driver sets SCLK, to
allow setups where the host generates additional bits per LRCLK
phase to increase the SCLK frequency. In these cases the machine
driver would always have to inform this driver of the actual SCLK,
and it must select a legal SCLK.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210805161111.10410-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
An I2S frame starts on the falling edge of LRCLK so ASP_STP must
be 0.
At the same time, move other format settings in the same register
from cs42l42_pll_config() to cs42l42_set_dai_fmt() where you'd
expect to find them, and merge into a single write.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20210805161111.10410-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Both SCLK and PLL clocks must be running to drive the glitch-free mux
behind MCLK_SRC_SEL and complete the switchover.
This patch moves the writing of MCLK_SRC_SEL to when the PLL is started
and stopped, so that it only transitions while the PLL is running.
The unconditional write MCLK_SRC_SEL=0 in cs42l42_mute_stream() is safe
because if the PLL is not running MCLK_SRC_SEL is already 0.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 43fc357199 ("ASoC: cs42l42: Set clock source for both ways of stream")
Link: https://lore.kernel.org/r/20210805161111.10410-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver was defining two ALSA controls that both change the same
register field for the wind noise filter corner frequency. The filter
response has two corners, at different frequencies, and the duplicate
controls most likely were an attempt to be able to set the value using
either of the frequencies.
However, having two controls changing the same field can be problematic
and it is unnecessary. Both frequencies are related to each other so
setting one implies exactly what the other would be.
Removing a control affects user-side code, but there is currently no
known use of the removed control so it would be best to remove it now
before it becomes a problem.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20210803160834.9005-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The underlying register field has inverted sense (0 = enabled) so
the control definition must be marked as inverted.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20210803160834.9005-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
An I2S frame always has a left and right channel slot even if mono
data is being sent. So if channels==1 the actual bitclock frequency
is 2 * snd_soc_params_to_bclk(params).
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2cdba9b045 ("ASoC: cs42l42: Use bclk from hw_params if set_sysclk was not called")
Link: https://lore.kernel.org/r/20210729170929.6589-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver has no support for left-justified protocol so it should
not have been allowing this to be passed to cs42l42_set_dai_fmt().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20210729170929.6589-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ADC volume is a signed 8-bit number with range -97 to +12,
with -97 being mute. Use a SOC_SINGLE_S8_TLV() to define this
and fix the DECLARE_TLV_DB_SCALE() to have the correct start and
mute flag.
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210729170929.6589-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Jack must be connected before reporting button events and
if the jack is disconnected button release must be reported
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Message-Id: <20210525090822.64577-4-tanureal@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Add support for 2.4MHz clock source
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Message-Id: <20210525090822.64577-3-tanureal@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Add support for 24bits, 2 channels, 48k Sample rate bit clock
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Message-Id: <20210525090822.64577-2-tanureal@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
The 16 Bits, 2 channels, 48K sample rate use case needs
to configure a safer pll_divout during the start of PLL
After 800us from the start of PLL the correct pll_divout
can be set
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Message-Id: <20210525090822.64577-1-tanureal@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
HSBIAS_SENSE_EN configures HSBIAS output current sense through
the external 2.21-k resistor. HSBIAS_SENSE is hardware feature to reduce
the potential pop noise during the headset plug out slowly. But on some
platforms ESD voltage will affect it causing test to fail, especially
with CTIA headset type. For different hardware setups, a designer might
want to tweak default behavior.
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210511145220.125760-1-vitalyr@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cs42l42 does not support standard burst transfers so the use_single_read
and use_single_write flags must be set in the regmap config.
Because of this bug, the patch:
commit 0a0eb567e1 ("ASoC: cs42l42: Minor error paths fixups")
broke cs42l42 probe() because without the use_single_* flags it causes
regmap to issue a burst read.
However, the missing use_single_* could cause problems anyway because the
regmap cache can attempt burst transfers if these flags are not set.
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210511132855.27159-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre requested I have a look at some cppcheck warnings in the cs42l42
driver, since it is reassigning the ret variable without ever checking
the result. Looking a bit more broadly this happens in quite a few
legacy Cirrus parts, as they all use the same process to read the ID,
factor out a small helper so they can all share the same code. Whilst
in there fix up a couple of other trivial error path issues as well.
Thanks,
Charles
Charles Keepax (10):
ASoC: cirrus: Add helper function for reading the device ID
ASoC: cs35l32: Minor error paths fixups
ASoC: cs35l33: Minor error paths fixups
ASoC: cs35l34: Minor error paths fixups
ASoC: cs35l35: Minor error paths fixups
ASoC: cs35l35: Correct errata handling
ASoC: cs42l42: Minor error paths fixups
ASoC: cs42l73: Minor error paths fixups
ASoC: cs43130: Minor error paths fixups
ASoC: cs53l30: Minor error paths fixups
sound/soc/codecs/cirrus_legacy.h | 21 +++++++++++++++++++++
sound/soc/codecs/cs35l32.c | 34 ++++++++++++++++++----------------
sound/soc/codecs/cs35l33.c | 15 +++++++++------
sound/soc/codecs/cs35l34.c | 39 ++++++++++++++++++++++-----------------
sound/soc/codecs/cs35l35.c | 21 ++++++++++-----------
sound/soc/codecs/cs35l35.h | 1 +
sound/soc/codecs/cs42l42.c | 18 ++++++++----------
sound/soc/codecs/cs42l73.c | 30 +++++++++++++++++-------------
sound/soc/codecs/cs43130.c | 31 +++++++++++++++++++------------
sound/soc/codecs/cs53l30.c | 22 +++++++++++-----------
10 files changed, 136 insertions(+), 96 deletions(-)
create mode 100644 sound/soc/codecs/cirrus_legacy.h
--
2.11.0
Correct some unchecked re-allocations of ret whilst reading the device
ID and ensure the hardware state is returned to off on the error
paths.
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210510131357.17170-8-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the device_property APIs so that the code will work on devicetree
and ACPI systems.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210426155303.853236-2-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the internal jack creation by set_jack call, so users can map
buttons in their machine driver
Also only enable jack detection IRQ after set_jack call
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210426155303.853236-1-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The PLL is only needed for sclk < 11289600 Hz and cs42l42_pll_config()
will not configure it for higher rates. So it must only be enabled
when it is needed.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210306185553.62053-15-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There must be a delay of at least 150us after writing SCLK_PRESENT
before issuing another I2C write.
This is done using struct reg_sequence because it can specify a delay
after the write and the whole sequence is written atomically.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210306185553.62053-14-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for reading the source clock from snd_soc_params_to_bclk
so the machine driver is not required to call cs42l42_set_sysclk
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210306185553.62053-13-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Report the Jack events to the user space through ALSA.
Also moves request_threaded_irq() to component_probe so it don't get
interrupts before the initialization the struct snd_soc_jack.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210306185553.62053-12-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This delay is part of the power-up sequence defined in the datasheet.
A runtime_resume is a power-up so must also include the delay.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210305173442.195740-6-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver was setting bit clock polarity opposite to intended polarity.
Also simplify the code by grouping ADC and DAC clock configurations into
a single field.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210305173442.195740-2-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_digital_mute() is internally using both
mute_stream() (1) or digital_mute() (2), but the difference between
these 2 are only handling direction.
We can merge digital_mute() into mute_stream
int snd_soc_dai_digital_mute(xxx, int direction)
{
...
else if (dai->driver->ops->mute_stream)
(1) return dai->driver->ops->mute_stream(xxx, direction);
else if (direction == SNDRV_PCM_STREAM_PLAYBACK &&
dai->driver->ops->digital_mute)
(2) return dai->driver->ops->digital_mute(xxx);
...
}
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/87r1tlwiwe.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to use snd_soc_component_read()
instead of snd_soc_component_read32()
This patch renames _read32() to _read()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87a7134mc4.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure is only stored in the ops field of a snd_soc_dai_driver
structure. That field is declared const, so snd_soc_dai_ops structures
that have this property can be declared as const also.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The gpiod API checks for NULL descriptors, so there is no need to
duplicate the check in the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/cs42l42.c:1972:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: James Schulman <james.schulman@cirrus.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for Cirrus Logic CS42L42 codec. SoundWire support
is not enabled. Features support for I2C control and I2S audio.
Signed-off-by: James Schulman <james.schulman@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Richard Fitzgerald