For RK3399's GRF module, if we want to operate the graphic related grf
registers, we need to enable the pclk_vio_grf which supply power for VIO
GRF IOs, so it's better to introduce an optional grf clock in driver.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
The hardware IC designed that VOP must output the RGB10 video format to
eDP contoller, and if eDP panel only support RGB8, then eDP contoller
should cut down the video data, not via VOP contoller, that's why we need
to hardcode the VOP output mode to RGA10 here.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Rockchip VOP couldn't output YUV video format for eDP controller, so
when driver detect connector support YUV video format, we need to hack
it down to RGB888.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Some boards don't need to declare a panel device node, like the
display interface is DP monitors, so it's necessary to make the
panel detect to an optional action.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
RK3399 and RK3288 shared the same eDP IP controller, only some light
difference with VOP configure and GRF configure.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
eDP controller need to declare which vop provide the video source,
and it's defined in GRF registers.
But different chips have different GRF register address, so we need to
create a device data to declare the GRF messages for each chips.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Currently the driver calls drm_dev_register() directly after allocating
the DRM device and then continues with further initialization. This is
incorrect, because drm_dev_register() is supposed to be called after all
initialization is done. This problem was masked by the fact that
drm_dev_register() did not use to do anything special before, but
recently it started to call drm_connector_register_all(), which leads to
a crash if the driver is not fully initialized.
This patch fixes the problem by moving the call to drm_dev_register() to
the end of the initialization sequence and also removing the, now
unnecessary, call to drm_connector_register_all() from driver code.
Fixes: f706974a69 ("drm/rockchip: Drop drm_driver.load/unload callbacks")
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
[danvet: Fix up cleanup labels a bit.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466483254-35373-1-git-send-email-tfiga@chromium.org
drm_plane_helper_check_update() needs to account for the plane rotation
for correct clipping/scaling calculations. Do so.
There was an earlier attempt [1] to add this into
intel_check_primary_plane() but I requested that it'd be put into the
helper instead. An updated patch never materialized AFAICS, so I went
ahead and cooked one up myself.
v2: Deal with new drm_plane_helper_check_update() callers
[1] https://patchwork.freedesktop.org/patch/65177/
Cc: Nabendu Maiti <nabendu.bikash.maiti@intel.com>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466172790-10025-1-git-send-email-ville.syrjala@linux.intel.com
The rockchip drm driver started using drm_gem_cma_vm_ops, but that might
not be part of the kernel, causing the link to fail:
drivers/gpu/built-in.o:(.data+0xb234): undefined reference to `drm_gem_cma_vm_ops'
This adds a Kconfig 'select' statement to enable it like the other
user do.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 80f67cd80a ("drm/rockchip: Use cma gem vm ops")
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160616122800.1174015-1-arnd@arndb.de
The DP needs to have resumed once the DRM driver calls
drm_atomic_helper_resume, otherwise the DP clock is still disabled when
the DRM core enables the DP bridge.
Would be nice to use device_pm_wait_for_dev to synchronize these
devices, but the DRM device doesn't know what specific implementation
this bridge has.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Caesar Wang <wxt@rock-chips.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465224813-7359-2-git-send-email-tomeu.vizoso@collabora.com
This driver was still using the old legacy helpers and that caused a few
NULL dereferences when trying to call empty callbacks.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Caesar Wang <wxt@rock-chips.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465224813-7359-1-git-send-email-tomeu.vizoso@collabora.com
This is now handled by the core, drivers can totally ignore lifetime
issues of drm events.
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Mark yao <mark.yao@rock-chips.com>
Tested-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465388359-8070-11-git-send-email-daniel.vetter@ffwll.ch
With the various bits fixed rockchip now has an atomic compliant
handling/signalling of crtc_state->event, which means we can just
switch over to the new nonblocking helpers and remove some code.
v2: Fixes from Tomeu.
v3: Send out vblank events correctly when shutting down a crtc for
good. This is part of the atomic interface contract.
v4: Properly protect vop->event.
v5: Add more WARN_ON to check vop->event isn't clobbered.
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Mark yao <mark.yao@rock-chips.com>
Tested-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
It's not permissible to look at plane->state from interrupt context,
since doing that would need the irq handler to acquire the
plane->mutex lock.
The other problem is that if we pipeline updates using the new
nonblocking atomic helpers new state gets commit before the irq
handler fires, resulting in a lost event.
Fix both issues by caching the necessary values in vop_win, protected
by dev->event_lock.
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Mark yao <mark.yao@rock-chips.com>
Tested-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465388359-8070-19-git-send-email-daniel.vetter@ffwll.ch
With atomic helpers there's no need to track the enabled state of a pipe
any more, because atomic helpers track this accurately already.
Just disable the early returns, since the debug checks might be useful.
v2: Don't call drm_helper_disable_unused_functions, it blows up
without this check. At least explains why rockchip still needed this
old legacy-style state tracing - to work around issues from calling
other legacy style functions!
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Mark yao <mark.yao@rock-chips.com>
Tested-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465388359-8070-18-git-send-email-daniel.vetter@ffwll.ch
Rockchip DRM does not yet build properly for ARM64, but we might as well
get the printf formatting correct now, to avoid the following warnings:
drivers/gpu/drm/rockchip/rockchip_drm_fbdev.c: In function 'rockchip_drm_fbdev_create':
drivers/gpu/drm/rockchip/rockchip_drm_fbdev.c:111:2: warning: format '%d' expects argument of type 'int', but argument 8 has type 'size_t' [-Wformat=]
DRM_DEBUG_KMS("FB [%dx%d]-%d kvaddr=%p offset=%ld size=%d\n",
^
drivers/gpu/drm/rockchip/rockchip_drm_gem.c: In function 'rockchip_gem_alloc_buf':
drivers/gpu/drm/rockchip/rockchip_drm_gem.c:41:3: warning: format '%x' expects argument of type 'unsigned int', but argument 2 has type 'size_t' [-Wformat=]
DRM_ERROR("failed to allocate %#x byte dma buffer", obj->size);
^
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465494392-92489-1-git-send-email-briannorris@chromium.org
As promised, piles of prep work all around:
- drm_atomic_state rework, prep for nonblocking commit helpers
- fence patches from Gustavo and Christian to prep for atomic fences and
some cool work in ttm/amdgpu from Christian
- drm event prep for both nonblocking commit and atomic fences
- Gustavo seems on a crusade against the non-kms-native version of the
vblank functions.
- prep work from Boris to nuke all the silly ->best_encoder
implementations we have (we really only need that for truly dynamic
cases like dvi-i vs dvi-d or dp mst selecting the right transcoder on
intel)
- prep work from Laurent to rework the format handling functions
- and few small things all over
* tag 'topic/drm-misc-2016-06-07' of git://anongit.freedesktop.org/drm-intel: (47 commits)
drm/dsi: Implement set tear scanline
drm/fb_cma_helper: Implement fb_mmap callback
drm/qxl: Remove useless drm_fb_get_bpp_depth() call
drm/ast: Remove useless drm_fb_get_bpp_depth() call
drm/atomic: Fix remaining places where !funcs->best_encoder is valid
drm/core: Change declaration for gamma_set.
Documentation: add fence-array to kernel DocBook
drm/shmobile: use drm_crtc_vblank_{get,put}()
drm/radeon: use drm_crtc_vblank_{get,put}()
drm/qxl: use drm_crtc_vblank_{get,put}()
drm/atmel: use drm_crtc_vblank_{get,put}()
drm/armada: use drm_crtc_vblank_{get,put}()
drm/amdgpu: use drm_crtc_vblank_{get,put}()
drm/virtio: use drm_crtc_send_vblank_event()
drm/udl: use drm_crtc_send_vblank_event()
drm/qxl: use drm_crtc_send_vblank_event()
drm/atmel: use drm_crtc_send_vblank_event()
drm/armada: use drm_crtc_send_vblank_event()
drm/doc: Switch to sphinx/rst fixed-width quoting
drm/doc: Drop kerneldoc for static functions in drm_irq.c
...
Now a drm_pending_event can either send a real drm_event or signal a
fence, or both. It allow us to signal via fences when the buffer is
displayed on the screen. Which in turn means that the previous buffer
is not in use anymore and can be freed or sent back to another driver
for processing.
v2: Comments from Daniel Vetter
- call fence_signal in drm_send_event_locked()
- remove unneeded !e->event check
v3: Remove drm_pending_event->destroy to fix a leak when e->file_priv
is not set.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> (v2)
[danvet: fix one e->destroy in arcpgu due to rebasing.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1464818821-5736-13-git-send-email-daniel.vetter@ffwll.ch
This was added in
commit 0a3e67a4ca
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Tue Sep 30 12:14:26 2008 -0700
drm: Rework vblank-wait handling to allow interrupt reduction.
to stay backwards-compatible with old UMS code that didn't even tell
the kernel when it did a modeset, so that the kernel could
save/restore vblank counters. At worst this means vblanks will be
somewhat funky on a setup that very likely no one still runs.
So let's just nuke it.
Plan B would be to set it unconditionally in drm_vblank_init for kms
drivers, instead of in each driver separately. So if this patch breaks
anything please only restore the hunks in drmP.h and drm_irq.c, plus
add a check for DRIVER_MODESET in drm_vblank_init.
Stumbled over this in a discussion on irc with Chris.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It's unused, and really this helper should only look at the state
structure and nothing else.
v2: Rebase on top of rockchip changes
v3: Drop unrelated hunk, spotted by Laurent.
v4: Rebase onto mtk driver merge.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Mark Yao <mark.yao@rock-chips.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1462804451-15318-1-git-send-email-daniel.vetter@ffwll.ch
drm_gem_object_lookup() has never required the drm_device for its file
local translation of the user handle to the GEM object. Let's remove the
unused parameter and save some space.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: dri-devel@lists.freedesktop.org
Cc: Dave Airlie <airlied@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
[danvet: Fixup kerneldoc too.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ofc I promise just a few leftovers for drm-misc and somehow it's the
biggest pull. But really mostly trivial stuff:
- MAINTAINERS updates from Emil
- rename async to nonblock in atomic_commit to avoid the confusion between
nonblocking ioctl and async flip (= not vblank synced), from Maarten.
Needs to be regened with newer drivers, but probably only after -rc1 to
catch them all.
- actually lockless gem_object_free, plus acked driver conversion patches.
All the trickier prep stuff already is in drm-next.
- Noralf's nice work for generic defio support in our fbdev emulation.
Keeps the udl hack, and qxl is tested by Gerd.
* tag 'topic/drm-misc-2016-05-04' of git://anongit.freedesktop.org/drm-intel: (47 commits)
drm: Fixup locking WARN_ON mistake around gem_object_free_unlocked
drm/etnaviv: Use lockless gem BO free callback
drm/imx: Use lockless gem BO free callback
drm/radeon: Use lockless gem BO free callback
drm/amdgpu: Use lockless gem BO free callback
drm/gem: support BO freeing without dev->struct_mutex
MAINTAINERS: Add myself for the new VC4 (RPi GPU) graphics driver.
MAINTAINERS: Add a bunch of legacy (UMS) DRM drivers
MAINTAINERS: Add a few DRM drivers by Dave Airlie
MAINTAINERS: List the correct git repo for the Renesas DRM drivers
MAINTAINERS: Update the files list for the Renesas DRM drivers
MAINTAINERS: Update the files list for the Armada DRM driver
MAINTAINERS: Update the files list for the Rockchip DRM driver
MAINTAINERS: Update the files list for the Exynos DRM driver
MAINTAINERS: Add maintainer entry for the VMWGFX DRM driver
MAINTAINERS: Add maintainer entry for the MSM DRM driver
MAINTAINERS: Add maintainer entry for the Nouveau DRM driver
MAINTAINERS: Update the files list for the Etnaviv DRM driver
MAINTAINERS: Remove unneded wildcard for the i915 DRM driver
drm/atomic: Add WARN_ON when state->acquire_ctx is not set.
...
After async atomic_commit callback, drm_atomic_clean_old_fb will
clean all old fb, but because async, the old fb may be also on
the vop hardware, dma will access the old fb buffer, clean old
fb will cause iommu page fault.
Reference the fb and unreference it when the fb actuall swap out
from vop hardware.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Some rockchip vop not support iommu, need use non-iommu
buffer for it. And if we get iommu issues, we can compare
the issues with non-iommu path, that would help the debug.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
We need to take care of the vop status when use
rockchip_drm_crtc_mode_config, if vop is disabled,
the function would failed, that is terrible.
Save output_type and output_mode into rockchip_crtc_state,
it's nice to make them into atomic.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Tested-by: John Keeping <john@metanate.com>
We were accidentally returning PTR_ERR(NULL) which means success when we
wanted to return a negative error code.
Fixes: 412d4ae6b7 ('drm/rockchip: hdmi: add Innosilicon HDMI support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Yakir Yang <ykk@rock-chips.com>
arm_iommu_attach_device() takes its own reference to the mapping we give
it. Since we do not keep a reference to the mapping ourselves, we must
release it before returning.
Also fix the error path, which fails to release the mapping if it has
called arm_iommu_detach_device() since that clears archdata.mapping.
Signed-off-by: John Keeping <john@metanate.com>
The call to arm_iommu_detach_device() on the previous line sets
dev->archdata.mapping to NULL so this call is always a no-op.
Signed-off-by: John Keeping <john@metanate.com>
This pull request want to land the analogix_dp driver into drm/bridge directory,
which reused the Exynos DP code, and add Rockchip DP support. And those
patches have been:
* 'drm-next-analogix-dp-v2' of github.com:yakir-Yang/linux:
drm: bridge: analogix/dp: Fix the possible dead lock in bridge disable time
drm: bridge: analogix/dp: add panel prepare/unprepare in suspend/resume time
drm: bridge: analogix/dp: add edid modes parse in get_modes method
drm: bridge: analogix/dp: move hpd detect to connector detect function
drm: bridge: analogix/dp: try force hpd after plug in lookup failed
drm: bridge: analogix/dp: add max link rate and lane count limit for RK3288
drm: bridge: analogix/dp: add some rk3288 special registers setting
dt-bindings: add document for rockchip variant of analogix_dp
drm: rockchip: dp: add rockchip platform dp driver
ARM: dts: exynos/dp: remove some properties that deprecated by analogix_dp driver
dt-bindings: add document for analogix display port driver
drm: bridge: analogix/dp: dynamic parse sync_pol & interlace & dynamic_range
drm: bridge: analogix/dp: remove duplicate configuration of link rate and link count
drm: bridge: analogix/dp: fix some obvious code style
drm: bridge: analogix/dp: rename register constants
drm/exynos: dp: rename implementation specific driver part
drm: bridge: analogix/dp: split exynos dp driver to bridge directory
Rockchip have three clocks for dp controller, we leave pclk_edp
to analogix_dp driver control, and keep the sclk_edp_24m and
sclk_edp in platform driver.
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Rockchip dw_hdmi driver just called platform_set_drvdata() to get
your hopes up that maybe, somehow, you'd be able to retrieve the 'struct
rockchip_hdmi' from a pointer to the 'struct device'. You can't. When
we call dw_hdmi_bind() the main driver calls dev_set_drvdata(), which
clobbers our setting.
Let's just remove the platform_set_drvdata() to avoid dashing people's
hopes.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
This fixes a few problems in the vop crtc cleanup (handling error
paths and cleanup upon exit):
* The vop_create_crtc() error path had an unsafe version of the
iterator used for iterating over all planes (though it was
destroying planes in the iterator so should have used the safe
version)
* vop_destroy_crtc() - wasn't calling vop_plane_destroy(), which made
slub_debug unhappy, at least if we ended up running this due to a
deferred probe.
* In vop_create_crtc() if we were missing the "port" device tree node
we would fail but not return an error (found by code inspection).
Fix these problems.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
The drm_encoder_cleanup() was missing both from the error path of
dw_hdmi_rockchip_bind(). This caused a crash when slub_debug was
enabled and we ended up deferring probe of HDMI at boot.
This call isn't needed from unbind() because if dw_hdmi_bind() returns
no error then it takes over the job of freeing the encoder (in
dw_hdmi_unbind).
Signed-off-by: Douglas Anderson <dianders@chromium.org>
When a VOP is re-enabled, it will start scanning right away the
framebuffers that were configured from the last time, even if those have
been destroyed already.
To prevent the VOP from trying to access freed memory, disable all its
windows when the CRTC is being disabled, then each window will get a
valid framebuffer address before it's enabled again.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Link: http://lkml.kernel.org/g/CAAObsKAv+05ih5U+=4kic_NsjGMhfxYheHR8xXXmacZs+p5SHw@mail.gmail.com
When closing the DRM device while a vblank is pending, we access
file_priv after it has been free'd, which gives:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
PC is at __list_add+0x5c/0xe8
LR is at send_vblank_event+0x54/0x1f0
...
[<c02952e8>] (__list_add) from [<c031a7b4>] (send_vblank_event+0x54/0x1f0)
[<c031a760>] (send_vblank_event) from [<c031a9c0>] (drm_send_vblank_event+0x70/0x78)
[<c031a950>] (drm_send_vblank_event) from [<c031a9f8>] (drm_crtc_send_vblank_event+0x30/0x34)
[<c031a9c8>] (drm_crtc_send_vblank_event) from [<c0339ad8>] (vop_isr+0x224/0x28c)
[<c03398b4>] (vop_isr) from [<c0081780>] (handle_irq_event_percpu+0x12c/0x3e4)
This can be triggered somewhat reliably with:
modetest -M rockchip -v -s ...
Add a preclose hook to the driver so that we can discard any pending
vblank events when the device is closed.
Signed-off-by: John Keeping <john@metanate.com>
If the geometry of a crtc is changing in an atomic update then we must
validate the plane size against the new state of the crtc and not the
current size, otherwise if the crtc size is increasing the plane will be
cropped at the previous size and will not fill the screen.
Signed-off-by: John Keeping <john@metanate.com>
- Add and make use of drm_of_active_endpoint helpers
- Silence a noisy dev_info into a dev_dbg
- Stop touching primary fb on pageflips
- Track flip state explicitly
- Keep GEM buffer objects referenced while scanout is active
- Implement fence sync by deferring flips to a workqueue for
dma-bufs with pending fences
- Actually disable vblank IRQs while they are not needed
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ufbY
-----END PGP SIGNATURE-----
Merge tag 'imx-drm-next-20160301' of git://git.pengutronix.de/git/pza/linux into drm-next
imx-drm vblank IRQ control, fence support, and of endpoint helpers
- Add and make use of drm_of_active_endpoint helpers
- Silence a noisy dev_info into a dev_dbg
- Stop touching primary fb on pageflips
- Track flip state explicitly
- Keep GEM buffer objects referenced while scanout is active
- Implement fence sync by deferring flips to a workqueue for
dma-bufs with pending fences
- Actually disable vblank IRQs while they are not needed
* tag 'imx-drm-next-20160301' of git://git.pengutronix.de/git/pza/linux:
drm/imx: only enable vblank IRQs when needed
drm/imx: implement fence sync
drm/imx: keep GEM object referenced as long as scanout is active
drm/imx: track flip state explicitly
drm/imx: don't touch primary fb on pageflip
drm/imx: ipuv3 plane: Replace dev_info with dev_dbg if a plane's CRTC changes
gpu: ipu-v3: ipu-dc: Simplify display controller microcode setup
drm/rockchip: remove rockchip_drm_encoder_get_mux_id
drm/imx: remove imx_drm_encoder_get_mux_id
drm: add drm_of_encoder_active_endpoint helpers
It is replaced by drm_of_encoder_active_endpoint_id.
Suggested-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Yakir Yang <ykk@rock-chips.com>
[for dw_hdmi-rockchip]
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The Innosilicon HDMI is a low power HDMI 1.4 transmitter
IP, and it have been integrated on some rockchip CPUs
(like RK3036, RK312x).
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
If DRM_FBDEV_EMULATION is not selected in the config then we can save a
bit of space by not including the framebuffer code.
Signed-off-by: John Keeping <john@metanate.com>
args->pitch and args->size may not be set by userspace, sometimes
userspace only malloc args and not memset args to zero, then
args->pitch and args->size is random, it is very danger to use
pitch/size on gem.
pitch's type is u32, and min_pitch's type is int, example,
pitch is 0xffffffff, then pitch < min_pitch return true, then gem will
alloc very very big bufffer, it would eat all the memory and cause kernel
crash.
Stop using pitch/size from args, calc them from other args.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
As commented in drm_atomic_helper_wait_for_vblanks(), userspace relies
on cursor ioctls being unsynced. Converting the rockchip driver to
atomic has significantly impacted cursor performance by making every
cursor update wait for vblank.
By skipping the vblank sync when the framebuffer has not changed (as is
done in drm_atomic_helper_wait_for_vblanks()) we can avoid this for the
common case of moving the cursor and only need to delay the cursor ioctl
when the cursor icon changes.
We cannot add the check on legacy_cursor_update since that results in
the cursor bo being unreferenced while the hardware may still be reading
it. Fully supporting unsynced cursor updates is left for the future
when the atomic helper framework supports async updates.
Signed-off-by: John Keeping <john@metanate.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
The function can return negative value so it should be assigned to signed
variable.
The problem has been detected using patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Commit dbb3d94 (drm/rockchip: vop: move interrupt registers into
vop_data) introduced new macros for updating the interrupt control
registers but these always use the mask from the register definition
without refining it for the particular bits that are being changed.
This means that whenever we enable/disable a particular interrupt we end
up disabling all of the others as a side effect.
Signed-off-by: John Keeping <john@metanate.com>
Now rockchip_drm_vop.c is build into rockchipdrm.ko, so
no need to export following symbol anymore:
rockchip_drm_dma_attach_device
rockchip_drm_dma_detach_device
rockchip_drm_dma_attach_device
rockchip_drm_dma_detach_device
rockchip_register_crtc_funcs
rockchip_unregister_crtc_funcs
rockchip_fb_get_gem_obj
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
rockchip_drm_vop's module init had moved to rockchip_vop_reg.c
so no need to build rockchip_drm_vop.ko
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Add support for Synopsys DesignWare MIPI DSI controller which is
embedded in the rk3288 SoCs.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Since the mipi dsi driver need to use the clock of vop to make the
calculation of Blanking. But sometimes the clock driver can not set a
accurate clock_rate for vop, get it by clk_round_rate before mode_set,
so we can get the true value.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Fixes: a67719d182 ("drm/rockchip: vop: spilt register related into rockchip_reg_vop.c")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
RK3036 registers layout is quite difference with rk3288 layout,
The IC design with different framework, rk3036 vop is VOP LITE,
and rk3288 is VOP FULL.
RK3036 support two overlay plane and one hwc plane, max output
resolution is 1080p. it support IOMMU, and its IOMMU same as
rk3288's.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
There are two version scale control register found on vop,
scale full version found on rk3288, support extension registers.
and scale little version found on rk3036, only support common scale.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Both connecter gate and out_mode are not conflict with mode set
configure. Direct setting connecter gate and out_mode, that allow
connector do rockchip_drm_crtc_mode_config after mode set.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
If drm core requests a async commit, rockchip_drm_atomic_commit
will schedule a work task to update later.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Rk3288 vop timing registers is immediately register, when configure
timing on display active time, will cause tearing. use dclk reset is
not a good idea to avoid this tearing. we can avoid tearing by using
standby register.
Vop standby register will take effect at end of current frame, and
go back to work immediately when exit standby.
So we can use standby register to protect this context.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Rockchip vop not support hw vblank counter, needed check the committed
register if it's really take effect.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
For vop, power by enable/disable is more suitable then legacy dpms
function, and enable/disable more closely to the new atomic API.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
No functional update, drm_vblank_* is the legacy version of
drm_crtc_vblank_*. and use new api make driver more clean.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
The following code pattern exists in some DRM drivers:
ddev = drm_dev_alloc(&driver, parent_dev);
drm_dev_set_unique(ddev, dev_name(parent_dev));
(Sometimes dev_name(ddev->dev) is used, which is the same.)
As suggested in
http://lists.freedesktop.org/archives/dri-devel/2015-December/096441.html,
the unique name of a new DRM device can be set as dev_name(parent_dev)
when parent_dev is not NULL (vgem is a special case).
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_dev_set_unique() uses a format string to define the unique name of a
device. This feature is not used as currently all the calls to this
function either use "%s" as a format string or directly use
dev_name().
Even though this second kind of call does not introduce security
problems, because there cannot be "%" characters in dev_name() results,
gcc issues a warning when building with -Wformat-security flag
("warning: format string is not a string literal (potentially
insecure)"). This warning is useful to find real bugs like the one
fixed by commit 3958b79266 ("configfs: fix kernel infoleak through
user-controlled format string"). False positives which do not bring
an extra value make the work of finding real bugs harder.
Therefore remove the format-string feature from drm_dev_set_unique().
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1449829228-4425-1-git-send-email-nicolas.iooss_linux@m4x.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Done with coccinelle for the most part. However, it thinks '...' is
part of the semantic patch, so I put an 'int DOTDOTDOT' placeholder
in its place and got rid of it with sed afterwards.
@@
identifier dev, encoder, funcs;
@@
int drm_encoder_init(struct drm_device *dev,
struct drm_encoder *encoder,
const struct drm_encoder_funcs *funcs,
int encoder_type
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, encoder, funcs;
@@
int drm_encoder_init(struct drm_device *dev,
struct drm_encoder *encoder,
const struct drm_encoder_funcs *funcs,
int encoder_type
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4;
@@
drm_encoder_init(E1, E2, E3, E4
+ ,NULL
)
v2: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670818-2966-1-git-send-email-ville.syrjala@linux.intel.com
Done with coccinelle for the most part. It choked on
msm/mdp/mdp5/mdp5_plane.c like so:
"BAD:!!!!! enum drm_plane_type type;"
No idea how to deal with that, so I just fixed that up
by hand.
Also it thinks '...' is part of the semantic patch, so I put an
'int DOTDOTDOT' placeholder in its place and got rid of it with
sed afterwards.
I didn't convert drm_plane_init() since passing the varargs through
would mean either cpp macros or va_list, and I figured we don't
care about these legacy functions enough to warrant the extra pain.
@@
typedef uint32_t;
identifier dev, plane, possible_crtcs, funcs, formats, format_count, type;
@@
int drm_universal_plane_init(struct drm_device *dev,
struct drm_plane *plane,
unsigned long possible_crtcs,
const struct drm_plane_funcs *funcs,
const uint32_t *formats,
unsigned int format_count,
enum drm_plane_type type
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, plane, possible_crtcs, funcs, formats, format_count, type;
@@
int drm_universal_plane_init(struct drm_device *dev,
struct drm_plane *plane,
unsigned long possible_crtcs,
const struct drm_plane_funcs *funcs,
const uint32_t *formats,
unsigned int format_count,
enum drm_plane_type type
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4, E5, E6, E7;
@@
drm_universal_plane_init(E1, E2, E3, E4, E5, E6, E7
+ ,NULL
)
v2: Split crtc and plane changes apart
Pass NUL for no-name instead of ""
Leave drm_plane_init() alone
v3: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670795-2853-1-git-send-email-ville.syrjala@linux.intel.com
Done with coccinelle for the most part. However, it thinks '...' is
part of the semantic patch, so I put an 'int DOTDOTDOT' placeholder
in its place and got rid of it with sed afterwards.
I didn't convert drm_crtc_init() since passing the varargs through
would mean either cpp macros or va_list, and I figured we don't
care about these legacy functions enough to warrant the extra pain.
@@
identifier dev, crtc, primary, cursor, funcs;
@@
int drm_crtc_init_with_planes(struct drm_device *dev,
struct drm_crtc *crtc,
struct drm_plane *primary, struct drm_plane *cursor,
const struct drm_crtc_funcs *funcs
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, crtc, primary, cursor, funcs;
@@
int drm_crtc_init_with_planes(struct drm_device *dev,
struct drm_crtc *crtc,
struct drm_plane *primary, struct drm_plane *cursor,
const struct drm_crtc_funcs *funcs
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4, E5;
@@
drm_crtc_init_with_planes(E1, E2, E3, E4, E5
+ ,NULL
)
v2: Split crtc and plane changes apart
Pass NULL for no-name instead of ""
Leave drm_crtc_init() alone
v3: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670771-2751-1-git-send-email-ville.syrjala@linux.intel.com
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWZMgaAAoJEHm+PkMAQRiGGcIH+gNS/hbN2DKW7wphl1QuaV7C
1fror8AvpwbGa/o0yuxovaVuZzAR0TF31vn+gAemF4U/hnM25xqxEHXYZEVv8OWw
mbz4/z+jbVk3SiS5AiZPIZgL4W6RZnG5QYfiTVGPlBHuBznW2ITlNlClBOmBL45o
uhb3bjTzi70AZ7Gh6i9sHgJoHg6D9u/ZxLaLcWnM79BzyTMHTf2t0wnrQmh66lEE
hp7Rn9wXv9bk/e3iH7CVUb97P4IWhhkmfqcoturqAg9+C/M26b0VmvQp9Sy8S6Pd
FVQ+SUIZllj5ZDKe9mOcs37czlxTr0keEFqzWeMh/7y4iuI3RaRp/qb+7mX5sIE=
=WGZ1
-----END PGP SIGNATURE-----
Back merge tag 'v4.4-rc4' into drm-next
We've picked up a few conflicts and it would be nice
to resolve them before we move onwards.
Passing -1 as the pipe for vblank events now triggers a WARN_ON, but had
previously made multi-screen unusable anyway. Pass the correct pipe to
the event-send function, and use the new API to make this a bit easier
for us.
Fixes WARN present since cc1ef118fc for every pageflip event sent:
[ 209.549969] ------------[ cut here ]------------
[ 209.554592] WARNING: CPU: 3 PID: 238 at drivers/gpu/drm/drm_irq.c:924 drm_vblank_count_and_time+0x80/0x88 [drm]()
[ 209.564832] Modules linked in: [...]
[ 209.612401] CPU: 3 PID: 238 Comm: irq/41-ff940000 Tainted: G W 4.3.0-rc6+ #71
[ 209.620647] Hardware name: Rockchip (Device Tree)
[ 209.625348] [<c001bb80>] (unwind_backtrace) from [<c001615c>] (show_stack+0x20/0x24)
[ 209.633079] [<c001615c>] (show_stack) from [<c02b2c50>] (dump_stack+0x8c/0x9c)
[ 209.640289] [<c02b2c50>] (dump_stack) from [<c0052e88>] (warn_slowpath_common+0x94/0xc4)
[ 209.648364] [<c0052e88>] (warn_slowpath_common) from [<c0052f74>] (warn_slowpath_null+0x2c/0x34)
[ 209.657139] [<c0052f74>] (warn_slowpath_null) from [<bf17dc30>] (drm_vblank_count_and_time+0x80/0x88 [drm])
[ 209.666875] [<bf17dc30>] (drm_vblank_count_and_time [drm]) from [<bf17e484>] (drm_send_vblank_event+0x74/0x7c [drm])
[ 209.677385] [<bf17e484>] (drm_send_vblank_event [drm]) from [<bf4c1144>] (vop_win_state_complete+0x4c/0x70 [rockchip_drm_vop])
[ 209.688757] [<bf4c1144>] (vop_win_state_complete [rockchip_drm_vop]) from [<bf4c3bdc>] (vop_isr_thread+0x170/0x1d4 [rockchip_drm_vop])
[ 209.700822] [<bf4c3bdc>] (vop_isr_thread [rockchip_drm_vop]) from [<c00ab93c>] (irq_thread_fn+0x2c/0x50)
[ 209.710284] [<c00ab93c>] (irq_thread_fn) from [<c00abcac>] (irq_thread+0x13c/0x188)
[ 209.717927] [<c00abcac>] (irq_thread) from [<c00723c8>] (kthread+0xec/0x104)
[ 209.724965] [<c00723c8>] (kthread) from [<c0011638>] (ret_from_fork+0x14/0x3c)
[ 209.732171] ---[ end trace 0690bc604f5d535d ]---
Signed-off-by: Daniel Stone <daniels@collabora.com>
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Tested-By: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Thierry Reding <treding@nvidia.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
VOP_WINx_DSP_ST does not require subtracting 1 from the values written to
it. It actually causes the screen to be shifted by one pixel.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Tested-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dominik Behr <dbehr@chromium.org>
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Commit 371f0f085f ("ARM: 8426/1: dma-mapping: add missing range check
in dma_mmap()") introduced offset-checking for mappings, which collides
with the fake-offset the drm sets for gems.
Other drm-drivers set this offset to 0 before doing the mapping, so
this looks like the correct way to go for rockchip as well.
Fixes: 371f0f085f ("ARM: 8426/1: dma-mapping: add missing range check in dma_mmap()")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
When doing the initial setup both the hclk and the aclk need to be
enabled otherwise the board will simply hang. This only occurs when
building the vop driver as a module, when its built-in the initial setup
happens to run before the clock framework shuts of unused clocks
(including the aclk).
While there also switch to doing prepare and enable in one step rather
then separate steps to reduce the amount of code required.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Tested-by: Yakir Yang <ykk@rock-chips.com>
Tested-by: Romain Perier <romain.perier@gmail.com>
Drivers shouldn't clobber the passed in addfb ioctl parameters.
i915 was doing just that. To prevent it from happening again,
pass the struct around as const, starting all the way from
internal_framebuffer_create().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 52f5eb6094.
Rockchip drm can't work with generic drm_of_component_probe now
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Since
commit 131e663bd6
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jul 9 23:32:33 2015 +0200
drm/gem: rip out drm vma accounting for gem mmaps
there is no need for this any more.
v2: Fixup compile noise spotted by 0-day build.
Link: http://mid.gmane.org/1444894601-5200-9-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
drm_vblank_count() returns the software counter. We should not pretend
it's the hw counter since we use the hw counter to figuere out what the
software counter value should be. So instead provide a new function
drm_vblank_no_hw_counter() for drivers that don't have a real hw
counter. The new function simply returns 0, which is about the only
thing it can do.
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>
[danvet: s/int pipe/unsigned int pipe/ to follow Thierry's interface
change.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This continues the pattern started in commit cc1ef118fc ("drm/irq:
Make pipe unsigned and name consistent"). This is applied to the public
APIs and driver callbacks, so pretty much all drivers need to be updated
to match the new prototypes.
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Jianwei Wang <jianwei.wang.chn@gmail.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The registers will be reset to default values when whole
power domain off, so restore registers from regsbak.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Win2/3 support multiple area function, but we haven't found
a suitable way to use it yet, so let's just use them as other windows
with only area 0 enabled.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
vir_stride need number words of the virtual width, and fb->pitches
save bytes_per_pixel, so just div 4 switch to stride.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Since David Herrmann's mmap vma manager rework we don't need to grab
dev->struct_mutex any more to prevent races when looking up the mmap
offset. Drop it and instead don't forget to use the unref_unlocked
variant (since the drm core still cares).
Aside: I stumbled over the mmap handler which directly does a
dma_mmap_attrs. But totally fails to grab a reference on the
underlying object and hence looks like it happily just leaks the ptes
since there's no guarantee the mmap isn't still around when
gem_free_object is called. Which the kerneldoc of dma_mmap_attrs
explicitly forbids.
v2: Fixup compile fail 0-day spotted.
Cc: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Use the newly created wrapper drm_fb_helper functions instead of calling
core fbdev functions directly. They also simplify the fb_info creation.
This is an effort to create a top level drm fbdev emulation option.
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ok next attempt at drm-fixes pull. Big thing really is just the compat32
one for addfb2.1.
* tag 'topic/drm-fixes-2015-07-16' of git://anongit.freedesktop.org/drm-intel:
drm: Provide compat ioctl for addfb2.1
Documentation: drm: Fix tablulation in KMS properties table
drm: add a check for x/y in drm_mode_setcrtc
drm/rockchip: use drm_gem_mmap helpers
hardware cursor windows only have some fixed size, and not support
width virtual, when move hardware cursor windows outside of left,
the display would be wrong, so this window can't for cursor now.
And Tag hardware cursor window as a overlay is wrong, will make
userspace wrong behaviour.
So just remove the hardware cursor window
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Window 1 support scale and yuv format, it's waste use it for a
cursor, use window 3 is enough.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Rather than (incompletely [0]) re-implementing drm_gem_mmap() and
drm_gem_mmap_obj() helpers, call them directly from the rockchip mmap
routines.
Once the core functions return successfully, the rockchip mmap routines
can still use dma_mmap_attrs() to simply mmap the entire buffer.
[0] Previously, we were performing the mmap() without first taking a
reference on the underlying gem buffer. This could leak ptes if the gem
object is destroyed while userspace is still holding the mapping.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Add a check for the presence of fb_helper to rockchip_drm_output_poll_changed()
to only call drm_fb_helper_hotplug_event if there is actually a fb_helper
available. Without this check I see NULL pointer dereferences when the
hdmi hotplug irq fires before the fb_helper got initialized.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
VOP can support BGR formats in all windows thanks to red/blue swap option
provided in WINx_CTRL0 registers. This patch enables support for
ABGR8888, XBGR8888, BGR888 and BGR565 formats by using this feature.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Rather than (incompletely [0]) re-implementing drm_gem_mmap() and
drm_gem_mmap_obj() helpers, call them directly from the rockchip mmap
routines.
Once the core functions return successfully, the rockchip mmap routines
can still use dma_mmap_attrs() to simply mmap the entire buffer.
[0] Previously, we were performing the mmap() without first taking a
reference on the underlying gem buffer. This could leak ptes if the gem
object is destroyed while userspace is still holding the mapping.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These files are built off of a tristate Kconfig option and also contain
modular function calls so they should explicitly include module.h to
avoid compile breakage during header shuffles done in the future.
Cc: David Airlie <airlied@linux.ie>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
platform_get_irq() can return negative error values and we already test for
these. Therefore the variable holding this value should be signed to not
loose possible error values.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-By: Daniel Kurtz <djkurtz@chromium.org>
This set of patches adjust the setup of the HDMI CTS/N values for audio
support to be compliant with the work-around given in the iMX6 errata
documentation as part of the preparation for integrating audio support
for this driver, and also update the HDMI phy configuration for Rockchip
devices to improve the HDMI eye pattern.
* 'drm-dwhdmi-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm: rockchip/dw_hdmi-rockchip: improve for HDMI electrical test
drm: bridge/dw_hdmi: separate VLEVCTRL settting into platform driver
drm: bridge/dw_hdmi: fixed codec style
drm: bridge/dw_hdmi: adjust n/cts setting order
drm: bridge/dw_hdmi: protect n/cts setting with a mutex
drm: bridge/dw_hdmi: combine hdmi_set_clock_regenerator_n() and hdmi_regenerate_cts()
Conflicts:
drivers/gpu/drm/imx/dw_hdmi-imx.c
Convert all drm callers that use of_graph_get_next_endpoint to loop over
of-graph endpoints to the newly introduced for_each_endpoint_of_node
helper macro.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=la2O
-----END PGP SIGNATURE-----
Merge tag 'of-graph-drm-2015-04-08' of git://git.pengutronix.de/git/pza/linux into drm-next
drm: Use of-graph helpers to loop over endpoints
Convert all drm callers that use of_graph_get_next_endpoint to loop over
of-graph endpoints to the newly introduced for_each_endpoint_of_node
helper macro.
* tag 'of-graph-drm-2015-04-08' of git://git.pengutronix.de/git/pza/linux:
drm/rockchip: use for_each_endpoint_of_node macro, drop endpoint reference on break
drm/rcar-du: use for_each_endpoint_of_node macro
drm/imx: use for_each_endpoint_of_node macro in imx_drm_encoder_get_mux_id
drm: use for_each_endpoint_of_node macro in drm_of_find_possible_crtcs
of: Explicitly include linux/types.h in of_graph.h
dt-bindings: brcm: rationalize Broadcom documentation naming
of/unittest: replace 'selftest' with 'unittest'
Documentation: rename of_selftest.txt to of_unittest.txt
Documentation: update the of_selftest.txt
dt: OF_UNITTEST make dependency broken
MAINTAINERS: Pantelis Antoniou device tree overlay maintainer
of: Add of_graph_get_port_by_id function
of: Add for_each_endpoint_of_node helper macro
of: Decrement refcount of previous endpoint in of_graph_get_next_endpoint
Using the for_each_... macro should make the code a bit shorter and
easier to read. Also, when breaking out of the loop, the endpoint node
reference count needs to be decremented.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
drm/rockchip already has support for disabling all displays on suspend
and enabling them on resume.
Disable automatic VT switching on suspend by the pm console tracking
layer.
Tested on veyron, used `echo mem > sys/power/state`
=> verified no VT switch
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Register connectors with userspace after all components are bound.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Dominik Behr <dbehr@chromium.org>
drm_connector_get_name -> connector->name
This patch is necessary to make X11 see screens it seems.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The function disables the dclk at the beginning, so don't simply return
when an error happens, but instead enable the clock again, so that
enable and disable calls are balanced.
ret_clk is introduced to hold the clk_enable result and not mangle the
original error code.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
When pixel clock less than 148.5MHz, make sloopboost=2 tklvl=20
cklvl=13 increase rasing/falling time and increase data & clock
voltage driver.
When pixel clock less than 74.25MHz, make sloopboost=0 tklvl=19
cklvl=18, increase data and clock voltage driver.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Because of iMX6 & Rockchip have differnet mpll config parameter,
the VLEVCTRL parameter would be different. In this case we should
separate VLEVCTRL setting from the common dw_hdmi driver, config
this parameter in platform driver(dw_hdmi-imx and dw_hdmi-rockchip)
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
rockchip fixes.
* 'drm_next' of https://github.com/markyzq/kernel-drm-rockchip:
drm/rockchip: vop: power off until vop standby take effect
drm/rockchip: vop: set vop enabled after enable iommu
drm/rockchip: vop use is_enabled instead of dpms mode
drm/rockchip: vop: fix vop vsync/hsync polarity
drm/rockchip: Only alloc a kmap for fbdev gem object
Vop standby will take effect at end of current frame,
if dsp_hold_valid_irq happen, it means vop standby complete.
we must wait standby complete when we want to disable aclk,
if not, memory bus maybe dead.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
there is a Bug that:
vop_enable()->drm_vblank_on, drm_vblank_on may call vop
enable vblank. if it happen, vblank enable would failed,
then cause irq status error. because is_enabled value is set
after drm_vblank_on.
after enable vop clocks and iommu regs, we can sure that
R/W vop regs and do vop plane flip is safe, so place
is_enabled = true after enable iommu is suitable.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
drm dpms have many power modes: ON,OFF,SUSPEND,STANDBY, etc.
but vop only have enable/disable mode, maybe case such bug:
--> DRM_DPMS_ON: power on vop
--> DRM_DPMS_SUSPEND: power off vop
--> DRM_DPMS_OFF: already power off at SUSPEND, crash
so use a bool val is more suitable.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Vop set wrong vsync/hsync polarity, it may cause some
display problem. known problem is that caused HDMI hdcp
authenticate failed, caused pixel offset with hdmi display.
the polarity description at RK3288 TRM doc:
dsp_vsync_pol
VSYNC polarity
1'b0 : negative
1'b1 : positive
dsp_hsync_pol
HSYNC polarity
1'b0 : negative
1'b1 : positive
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
In general, the data in drm/rockchip GEM objects is never accessed by
the kernel. The objects are either accessed by a GPU, by display
controller DMA, or by mmap'ing them to user space. Thus, these
buffers need not be mapped into kernel address space.
The only exception is the fbdev framebuffer(s), which may be written
in-kernel by fbcon.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
What is passed to drm_fb_helper_fill_var() should be fb_width/fb_height,
rather than the surface size.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When the reset controller subsystem is disabled, this driver
fails to build:
drivers/gpu/drm/rockchip/rockchip_drm_vop.c: In function 'vop_initial':
drivers/gpu/drm/rockchip/rockchip_drm_vop.c:1267:2: error: implicit declaration of function 'devm_reset_control_get' [-Werror=implicit-function-declaration]
The easiest solution is to add a dependency in Kconfig to avoid
that case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Airlie <airlied@gmail.com>
commit 765d5b9c2b ("fbdev: fbcon: select VT_HW_CONSOLE_BINDING")
made FRAMEBUFFER_CONSOLE always select VT_HW_CONSOLE_BINDING, but forgot
to remove
select VT_HW_CONSOLE_BINDING if FRAMEBUFFER_CONSOLE
from the individual drivers' sections that already did this before.
Remove it, also from new drivers.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
dma_alloc_attrs() returns NULL if it cannot allocate a dma buffer (or
mapping), not a negative error code.
Rerported-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
To build the rockchip dw_hdmi driver as a module, the
rockchip_drm_encoder_get_mux_id and rockchip_drm_crtc_mode_config
functions need to be exported.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Rockchip RK3288 hdmi is compatible with dw_hdmi
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This patch adds the basic structure of a DRM Driver for Rockchip Socs.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Peter Chen