Some panels need to be configured with commands sent over the MIPI link,
which they will do in the prepare hook. Call this after the PHY has
been initialized so that we are able to send commands to the panel.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-12-john@metanate.com
By dereferencing the MIPI command buffer as a u32* we rely on it being
correctly aligned on ARM, but this may not be the case. Copy it into a
stack variable that will be correctly aligned.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-11-john@metanate.com
Requesting the HS clock from the PHY before we initialize it causes an
invalid signal to be sent out since the input clock is not yet
configured. The PHY databook suggests only asserting this signal when
performing HS transfers, so let's do that.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-10-john@metanate.com
Instead of always sending commands in LP mode, respect the
MIPI_DSI_MSG_USE_LPM flag to decide how to send each message. Also
request acks if MIPI_DSI_MSG_REQ_ACK is set.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-9-john@metanate.com
We want to check that both the GEN_CMD_EMPTY and GEN_PLD_W_EMPTY bits
are set so we can't just check "val & mask" because that will be true if
either bit is set.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-6-john@metanate.com
In a couple of places here we use "val" for the value that is about to
be written to a register but then reuse the same variable for the value
of a status register before we get around to writing it. Rename the
value to be written to so that we write the value we intend to and not
what we have just read from the status register.
Signed-off-by: John Keeping <john@metanate.com>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-5-john@metanate.com
This is not needed since we can access the mode via the CRTC from the
enable hook. Also remove the "mode" field that is no longer used.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-4-john@metanate.com
This shows that we only use the mode from the enable function and
prepares us to remove the "mode" field and the mode_set hook in the next
commit.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-3-john@metanate.com
With atomic modesetting the hardware will be powered off when the
mode_set function is called. We should configure the hardware in the
enable function, which is the atomic version of "commit" so let's use
the enable hook rather than commit while we're at it.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-2-john@metanate.com
Misc fixes for the 4.11 merge window.
- vmwgfx drm_control node compat patch
- rockchip&zte fix
- compat32 support for dma-buf ioctl (cc: stable ofc, since this is a
massive fumble. oops)
* tag 'drm-misc-next-fixes-2017-02-27' of git://anongit.freedesktop.org/git/drm-misc:
dma-buf: add support for compat ioctl
drm/vmwgfx: Work around drm removal of control nodes
drm/rockchip: cdn-dp: Fix error handling
drm/rockchip: add extcon dependency for DP
drm: zte: fix static checker warning on variable 'fmt'
Backmerge the main pull request to sync up with all the newly landed
drivers. Otherwise we'll have chaos even before 4.12 started in
earnest.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
It is likely that both 'clk_disable_unprepare()' should be called if
'pm_runtime_get_sync()' fails.
Add a new label for that, because 'err_set_rate' is not meaningful in this
case.
Add a missing call to 'pm_runtime_put()'.
Fixes: 1a0f7ed3ab ("drm/rockchip: cdn-dp: add cdn DP support for rk3399")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170220070815.23096-1-christophe.jaillet@wanadoo.fr
The newly added DP driver links against the extcon core, which fails when
extcon is a module and this driver is not:
drivers/gpu/drm/rockchip/cdn-dp-core.o: In function `cdn_dp_get_port_lanes':
cdn-dp-core.c:(.text.cdn_dp_get_port_lanes+0x24): undefined reference to `extcon_get_state'
cdn-dp-core.c:(.text.cdn_dp_get_port_lanes+0x44): undefined reference to `extcon_get_property'
Let's make Kconfig enforce correct behavior with a dependency.
Fixes: 1a0f7ed3ab ("drm/rockchip: cdn-dp: add cdn DP support for rk3399")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170214213215.2888509-1-arnd@arndb.de
Rockchip DRM used the arm special API, arm_iommu_*(), to attach
iommu for ARM32 SoCs. This patch convert to common iommu API
so it would support ARM64 like RK3399.
Since previous patch added support for direct IOMMU address space
management, there is no need to use DMA API anymore and this patch wires
things to use the new method.
Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
The API is not suitable for subsystems consisting of multiple devices
and requires severe hacks to use it. To mitigate this, this patch
implements allocation and address space management locally by using
helpers provided by DRM framework, like other DRM drivers do, e.g.
Tegra.
This patch should not introduce any functional changes until the driver
is made to attach subdevices into an IOMMU domain with the generic IOMMU
API, which will happen in following patch. Based heavily on GEM
implementation of Tegra DRM driver.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: rjan Eide <orjan.eide@arm.com>
The drm_mode_config helper private field points to a structure of
function pointers that don't need to be modified at runtime. Make it
const.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Acked-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170102091613.6310-1-laurent.pinchart@ideasonboard.com
Core code already makes drm_driver.get_vblank_counter hook optional by
letting drm_vblank_no_hw_counter be the default implementation for the
function hook. So the drm_vblank_no_hw_counter assignment in the driver
code becomes redundant and can be removed now.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1486458995-31018-3-git-send-email-shawnguo@kernel.org
Noticed that everyone duplicates the same logic here and we could safe
a few lines per driver. Yay for lots of drivers to make such tiny
refactors worth-while!
v2: Forgot to git add everything :(
v3: Actually remove release_fbi (Sean, Emil, Chris) ...
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207161603.17611-1-daniel.vetter@ffwll.ch
fix warning:
drivers/gpu/drm/rockchip/cdn-dp-reg.c:632:24: warning:
'val[1]' may be used uninitialized in this function [-Wmaybe-uninitialized]
msa_misc = 2 * val[0] + 32 * val[1] +
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
rockchip CDN-DP support.
* 'drm-rockchip-next-2017-02-05' of https://github.com/markyzq/kernel-drm-rockchip:
drm/rockchip: cdn-dp: don't configure hardware in mode_set
drm/rockchip: cdn-dp: retry to check sink count
drm/rockchip: cdn-dp: Move mutex_init to probe
drm/rockchip: cdn-dp: do not use drm_helper_hpd_irq_event
drm/rockchip: cdn-dp: Do not run worker while suspended
drm/rockchip: cdn-dp: Load firmware if no monitor connected
drm/rockchip: cdn-dp: add cdn DP support for rk3399
drm/rockchip: return ERR_PTR instead of NULL
drm/rockchip: vop: make vop register setting take effect
With atomic modesetting the hardware will be powered off when the
mode_set function is called. We should configure the hardware in the
enable function.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Sometimes the Dock is disconnected, but cdn_dp_encoder_disable is not
triggered by DRM. For example, unplug the Dock in console mode, and
re-plug it again, the cdn_dp_event_work will try to get the sink count
of Dock, since the DP is still active. But the Dock has been powered
down, it need re-power on, and wait for a while until it is ready to
DPCD communication.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
We're trying to lock mutex when cdn-dp shutdown, so we need to make
sure the mutex is inited in cdn-dp's probe.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
The cdn_dp_pd_event_work is using drm_helper_hpd_irq_event to update the
connector status, this function is used to update all connectors of
drm_device. Therefore, the detect of other connector will be call, when
cdn_dp_pd_event_work is triggered, every time. It is not necessary, and
it may cause system crash. replace drm_helper_hpd_irq_event with
drm_kms_helper_hotplug_event, only update cdn-dp status.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
If the driver is in suspended mode, the dp block may be disabled, and
chip registers may not be accessible. Yet, the worker may be triggered
in this situation by an extcon event. If that happens, the following crash
will be seen.
cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work] *ERROR* Enable dp failed -19
cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work] Connected, not enabled. Enabling cdn
Bad mode in Error handler detected, code 0xbf000002 -- SError
CPU: 1 PID: 10357 Comm: kworker/1:2 Not tainted 4.4.21-05903-ge0514ea #1
Hardware name: Google Kevin (DT)
Workqueue: events cdn_dp_pd_event_work
task: ffffffc0cda67080 ti: ffffffc0b9b80000 task.ti: ffffffc0b9b80000
PC is at cdn_dp_clock_reset+0x30/0xa8
LR is at cdn_dp_enable+0x1e0/0x69c
...
Call trace:
[<ffffffc0005a7e24>] cdn_dp_pd_event_work+0x58/0x3f4
[<ffffffc0002397f0>] process_one_work+0x240/0x424
[<ffffffc00023a28c>] worker_thread+0x2fc/0x424
[<ffffffc00023f5fc>] kthread+0x10c/0x114
[<ffffffc000203dd0>] ret_from_fork+0x10/0x40
Problem is two-fold: The worker should not run while suspended, and the
suspend function should not call cdn_dp_disable() while the worker is
running.
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
If no monitor is connected, suspend/resume cycles result in firmware
load errors because the driver attempts to load the firmware while
the system is in suspend state. This results in a kernel warning and
traceback.
Loading the firmware during boot fixes the problem. Note that we can not
just call schedule_work conditionally in cdn_dp_pd_event() if the insertion
status changed. The problem would still be seen if a monitor is connected
for the first time during suspend.
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Add support for cdn DP controller which is embedded in the rk3399
SoCs. The DP is compliant with DisplayPort Specification,
Version 1.3, This IP is compatible with the rockchip type-c PHY IP.
There is a uCPU in DP controller, it need a firmware to work,
please put the firmware file to /lib/firmware/rockchip/dptx.bin. The
uCPU in charge of aux communication and link training, the host use
mailbox to communicate with the ucpu.
The dclk pin_pol of vop must not be invert for DP.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
[seanpaul fixed up some races between the worker and modeset]
[seanpaul squashed ~15 commits from chromium.org gerrit]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
[groeck fixed compilation errors when building as module]
Signed-off-by: Guenter Roeck <groeck@chromium.org>
rockchip_drm_framebuffer_init is only used in one case, in
rockchip_drm_fbdev.c, where its return value is tested using IS_ERR. To
enable propagating the reason for the error, change the definition so that
it returns an ERR_PTR value.
Problem found with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
The setting of vop registers need a reg_done writing to take effect.
In vop_enable the vop return to work by by restoring registers, but the
registers do not take effect immediately, it should a vop_cfg_done
after it. The same thing is needed by windows_disabled in
vop_crtc_disable.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Instead of receiving the num_crts as a parameter, we can read it
directly from the mode_config structure. I audited the drivers that
invoke this helper and I believe all of them initialize the mode_config
struct accordingly, prior to calling the fb_helper.
I used the following coccinelle hack to make this transformation, except
for the function headers and comment updates. The first and second
rules are split because I couldn't find a way to remove the unused
temporary variables at the same time I removed the parameter.
// <smpl>
@r@
expression A,B,D,E;
identifier C;
@@
(
- drm_fb_helper_init(A,B,C,D)
+ drm_fb_helper_init(A,B,D)
|
- drm_fbdev_cma_init_with_funcs(A,B,C,D,E)
+ drm_fbdev_cma_init_with_funcs(A,B,D,E)
|
- drm_fbdev_cma_init(A,B,C,D)
+ drm_fbdev_cma_init(A,B,D)
)
@@
expression A,B,C,D,E;
@@
(
- drm_fb_helper_init(A,B,C,D)
+ drm_fb_helper_init(A,B,D)
|
- drm_fbdev_cma_init_with_funcs(A,B,C,D,E)
+ drm_fbdev_cma_init_with_funcs(A,B,D,E)
|
- drm_fbdev_cma_init(A,B,C,D)
+ drm_fbdev_cma_init(A,B,D)
)
@@
identifier r.C;
type T;
expression V;
@@
- T C;
<...
when != C
- C = V;
...>
// </smpl>
Changes since v1:
- Rebased on top of the tip of drm-misc-next.
- Remove mention to sti since a proper fix got merged.
Suggested-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170202162640.27261-1-krisman@collabora.co.uk
There's no need to duplicate identical code in multiple drivers (two at
the moment, one more to come soon). Move it to the dw-hdmi core where it
can be shared. If resource allocation ever becomes device-specific later
we'll always have the option of splitting it out again.
While it at pass the platform device to the bind function to avoid
having to cast struct device to struct platform_device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-8-laurent.pinchart+renesas@ideasonboard.com
The master argument isn't used. The data argument, a void pointer, is
used by the bind function only where it's cast to a drm_device pointer,
which can easily be obtained from the encoder argument instead. Remove
them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-3-laurent.pinchart+renesas@ideasonboard.com
Many drivers (21 to be exact) create connectors that are always
connected (for instance to an LVDS or DSI panel). Instead of forcing
them to implement a dummy .detect() handler, make the callback optional
and consider the connector as always connected in that case.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Vincent Abriou <vincent.abriou@st.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[seanpaul fixed small conflict in rcar-du/rcar_du_lvdscon.c]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Convert DT component matching to use component_match_add_release().
Acked-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/E1bwo6l-0005Io-Q1@rmk-PC.armlinux.org.uk
These GPU drivers only depend on the RESET_CONTROLLER config
option to fix build issues that existed when there weren't stub
reset APIs for reset controller consumers. Given that these
drivers aren't providing any reset controllers themselves, they
don't actually depend on the API to build (just to function) so
they don't need to depend on it. Remove the dependency to fix
recursive build errors like the following:
drivers/usb/Kconfig:39:error: recursive dependency detected!
drivers/usb/Kconfig:39: symbol USB is selected by MOUSE_APPLETOUCH
drivers/input/mouse/Kconfig:187: symbol MOUSE_APPLETOUCH depends on INPUT
drivers/input/Kconfig:8: symbol INPUT is selected by VT
drivers/tty/Kconfig:12: symbol VT is selected by FB_STI
drivers/video/fbdev/Kconfig:674: symbol FB_STI depends on FB
drivers/video/fbdev/Kconfig:5: symbol FB is selected by DRM_KMS_FB_HELPER
drivers/gpu/drm/Kconfig:42: symbol DRM_KMS_FB_HELPER is selected by DRM_KMS_CMA_HELPER
drivers/gpu/drm/Kconfig:98: symbol DRM_KMS_CMA_HELPER is selected by DRM_IMX
drivers/gpu/drm/imx/Kconfig:1: symbol DRM_IMX depends on IMX_IPUV3_CORE
drivers/gpu/ipu-v3/Kconfig:1: symbol IMX_IPUV3_CORE depends on RESET_CONTROLLER
drivers/reset/Kconfig:4: symbol RESET_CONTROLLER is selected by USB_CHIPIDEA
drivers/usb/chipidea/Kconfig:1: symbol USB_CHIPIDEA depends on USB_EHCI_HCD
drivers/usb/host/Kconfig:84: symbol USB_EHCI_HCD depends on USB
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: <dri-devel@lists.freedesktop.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Mark Yao <mark.yao@rock-chips.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: robdclark@gmail.com
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161018205719.20575-1-stephen.boyd@linaro.org
There's no point in enabling PSR when the panel doesn't support it.
This also avoids a problem when PSR gets enabled when a CRTC is being
disabled, because sometimes in that situation the DSP_HOLD_VALID_INTR
interrupt on which we wait will never arrive. This was observed on
RK3288 with a panel without PSR (veyron-jaq Chromebook).
It's very easy to reproduce by running the kms_rmfb test in IGT a few
times.
Cc: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1474639600-30090-2-git-send-email-tomeu.vizoso@collabora.com
We get 2 warnings when building kernel with W=1:
drivers/gpu/drm/rockchip/rockchip_drm_drv.c:309:6: warning: no previous prototype for 'rockchip_drm_fb_suspend' [-Wmissing-prototypes]
drivers/gpu/drm/rockchip/rockchip_drm_drv.c:318:6: warning: no previous prototype for 'rockchip_drm_fb_resume' [-Wmissing-prototypes]
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
So this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1474789388-3284-1-git-send-email-baoyou.xie@linaro.org
We get 2 warnings when building kernel with W=1:
drivers/gpu/drm/rockchip/rockchip_drm_fbdev.c:130:5: warning: no previous prototype for 'rockchip_drm_fbdev_init' [-Wmissing-prototypes]
drivers/gpu/drm/rockchip/rockchip_drm_fbdev.c:173:6: warning: no previous prototype for 'rockchip_drm_fbdev_fini' [-Wmissing-prototypes]
In fact, these functions are declared
in drivers/gpu/drm/rockchip/rockchip_drm_fbdev.h,
so this patch adds missing header dependencies.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1474789109-22010-1-git-send-email-baoyou.xie@linaro.org
I've included some improvements to PSR from myself, as well as a great
series from Tomasz to clean up and tighten up vblank/flip handling.
The last patch is one from Tomeu that has been floating around for a
while, and since rockchip is one of the beneficiaries, I figured this
would be a good place to pick it up.
* 'for-next' of ssh://people.freedesktop.org/~seanpaul/dogwood:
drm/rockchip: Balance irq refcount on failure
drm/rockchip: Kill vop_plane_state
drm/rockchip: Always signal event in next vblank after cfg_done
drm/rockchip: Do not enable vblank without event
drm/rockchip: Replace custom wait_for_vblanks with helper
drm/rockchip: Unreference framebuffers from flip work
drm/rockchip: Avoid race with vblank count increment
drm/rockchip: Get rid of some unnecessary code
drm/rockchip: Clear interrupt status bits before enabling
drm/rockchip: Fix up bug in psr state machine
drm/bridge: analogix_dp: Remove duplicated code
drm/rockchip: Reduce psr flush time to 100ms
drm/rockchip: Don't key off vblank for psr
There are many reasons other than ENOMEM that drm_dev_init() can
fail. Return ERR_PTR rather than NULL to be able to distinguish
these in the caller.
Signed-off-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20160921145919.13754-2-teg@jklm.no
If create_crtc fails in vop bind, ensure the irq refcount is zeroed
back out before exiting.
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
After changes introduced by last patches, there is no useful data stored
in vop_plane_state struct. Let's remove it and make the driver use
generic plane state alone.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
This patch makes the driver send the pending vblank event in next vblank
following the commit, relying on vblank signalling improvements done in
previous patches. This gives us vblank events that always represent the
real moment of changes hitting on the screen (which was the case only
for complete FB changes before) and lets us remove the manual window
update check.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Originally we needed to enable vblank for any atomic commit to kick the
PSR machine, but that was changed and we no longer need to do so from
a vblank interrupt. Let's return to original behavior of enabling
vblank only if it is really necessary.
This essentially reverts commit 5b6804034a ("drm/rockchip: Enable
vblank without event").
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Currently the driver uses a custom function to wait for flip to complete
after an atomic commit. It was needed before because of two problems:
- there is no hardware vblank counter, so the original helper would
have a race condition with the vblank interrupt,
- the driver didn't support unreferencing cursor framebuffers
asynchronously to the commit, which was what the helper expected.
Since both problems have been solved by previous patches, we can now
make the driver use the generic helper and remove custom waiting code.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Currently the driver waits for vblank and then unreferences old
framebuffers from atomic commit code path. This is however breaking the
legacy cursor API, which requires the updates to be fully asynchronous.
Instead of just adding a special case for cursor, we can have actually
smaller amount of code to unreference any changed framebuffer from a
flip work.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Since VOP does not have a hardware vblank count register, the ongoing
commit might be racing with a requested vblank interrupt, which would
increment the software vblank counter before the changes being committed
actually happen.
To avoid this, we can extend .atomic_flush(), so after it sets cfg_done
bit, it polls the vblank interrupt bit until it's inactive to make sure
that any old vblank interrupt gets to the handler and then uses
synchronize_irq(vop->irq) to make sure the handler finishes running.
The polling case should happen very rarely, but even if, the total wait
time should be relatively low and in practice almost equal to the vop
hardirq handler running time.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Current code implements prepare_fb and cleanup_fb callbacks only to
grab/release fb references, which is already done by atomic framework
when creating/destryoing plane state. Let's remove these
unused bits.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
The enable register only masks the raw status bits to signal CPU
interrupt only for enabled interrupts. The status bits are activated
regardless of the enable register. This means that we might have an old
interrupt event queued, which we are not interested in. To avoid getting
a spurious interrupt signalled, we have to clear the old bit before we
update the enable register.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
The ->set() callback would always be called when transitioning
from FLUSH->DISABLE since we assign state to psr->state right
above the skip condition.
Reported-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
3 seconds is a bit too conservative, drop this to 100ms for
better power savings.
Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Instead of keying off vblank for psr, just flush every time
we get an atomic update. This ensures that cursor updates
will properly disable psr (without turning vblank on/off),
and unifies the paths between fb_dirty and atomic psr
enable/disable.
Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
More -misc stuff
- moar drm_crtc.c split up&documentation
- some fixes for the simple kms helpers (Andrea)
- I included all the dri1 patches from David - we're not removing any code
or drivers, and it seems to have worked as a wake-up call to motivate a
few more people to upstream kms conversions for these. Feel free to
revert if you disagree strongly.
- a few other single patches
* tag 'topic/drm-misc-2016-08-31' of git://anongit.freedesktop.org/drm-intel: (24 commits)
drm: drm_probe_helper: Fix output_poll_work scheduling
drm: bridge/dw-hdmi: Fix colorspace and scan information registers values
drm/doc: Polish docs for drm_property&drm_property_blob
drm: Unify handling of blob and object properties
drm: Extract drm_property.[hc]
drm: move drm_mode_legacy_fb_format to drm_fourcc.c
drm/doc: Polish docs for drm_mode_object
drm: Remove drm_mode_object->atomic_count
drm: Extract drm_mode_object.[hc]
drm/doc: Polish kerneldoc for encoders
drm: Extract drm_encoder.[hc]
drm/fb-helper: don't call remove_conflicting_framebuffers for FB=m && DRM=y
drm/atomic-helper: Add NO_DISABLE_AFTER_MODESET flag support for plane commit
drm/atomic-helper: Disable appropriate planes in disable_planes_on_crtc()
drm/atomic-helper: Add atomic_disable CRTC helper callback
drm: simple_kms_helper: add support for bridges
drm: simple_kms_helper: make connector optional at init time
drm/bridge: introduce bridge detaching mechanism
drm/simple-helpers: Always add planes to the state update
drm: reduce GETCLIENT to a minimum
...
Drivers may set the NO_DISABLE_AFTER_MODESET flag in the 'flags' parameter
of the helper drm_atomic_helper_commit_planes() if the relevant display
controllers(e.g., IPUv3 for imx-drm) require to disable a CRTC's planes
when the CRTC is disabled. The helper would skip the ->atomic_disable
call for a plane if the CRTC of the old plane state needs a modesetting
operation. Of course, the drivers need to disable the planes in their CRTC
disable callbacks since no one else would do that.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1472461923-14364-1-git-send-email-gnuiyl@gmail.com
This pull request contains the following rockchip drm changes:
- Introduce support for rk3399 vop/crtc
- Add PSR framework to the rockchip driver
- Implement PSR in the rockchip analogix edp driver
- Fix panel on/off in analogix to avoid damaging panels
- Some miscellaneous fixes to clean up logs and code readability
* 'for-next' of git://people.freedesktop.org/~seanpaul/dogwood:
drm/rockchip: analogix_dp: drop unnecessary probe deferral "error" print
drm/rockchip: Enable vblank without event
drm/rockchip: Improve analogix-dp psr handling
drm/rockchip: A couple small fixes to psr
drm/rockchip: Use a spinlock to protect psr state
drm/rockchip: Don't use a delayed worker for psr state changes
drm/rockchip: Convert psr_list_mutex to spinlock and use it
drm/rockchip: analogix_dp: implement PSR function
drm/bridge: analogix_dp: add the PSR function support
drm/rockchip: add an common abstracted PSR driver
drm/rockchip: vop: export line flag function
drm/bridge: analogix_dp: Ensure the panel is properly prepared/unprepared
dt-bindings: add compatible strings for big/little rockchip vops
dt-bindings: sort Rockchip vop compatible by chip's number
drm/rockchip: vop: add rk3399 vop support
drm/rockchip: vop: introduce VOP_REG_MASK
drm/rockchip: sort registers define by chip's number
This driver is the only user of of_drm_find_panel() which prints an
error before doing probe deferral, yielding messages like this on boot,
before eventually succeeding:
[ 2.234271] [drm:rockchip_dp_probe] *ERROR* failed to find panel
...
[ 4.797539] [drm:rockchip_dp_probe] *ERROR* failed to find panel
...
Let's just drop the message.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
vblank should be enabled regardless of whether an event
is expected back. This is especially important for a cursor
plane.
Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Tested-by: Yakir Yang <ykk@rock-chip.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Remove the delayed worker, opting instead for the non-delayed
variety. Also introduce a lock to ensure we don't have races
with the worker and psr_state. Finally, cancel and wait for
the worker to finish when disabling the bridge.
Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
A few things that need tidying up, no functional changes.
Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
The handling of psr state is racey, shore that up with
a per-psr driver lock.
Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
The delayed worker isn't needed and is racey. Remove it and do
the state change in line.
Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
This patch converts the psr_list_mutex to a spinlock and locks
all access to psr_list to avoid races (however unlikely they
were).
Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Alway enable the PSR function for Rockchip analogix_dp driver. If panel
don't support PSR, then the core analogix_dp would ignore this setting.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
The PSR driver have exported four symbols for specific device driver, and
it's safe to call them in interrupt context:
- rockchip_drm_psr_register()
- rockchip_drm_psr_unregister()
- rockchip_drm_psr_enable()
- rockchip_drm_psr_disable()
- rockchip_drm_psr_flush()
Encoder driver should call the register/unregister interfaces to hook
itself into common PSR driver, encoder have implement the 'psr_set'
callback which use the set PSR state in hardware side.
Crtc driver would call the enable/disable interfaces when vblank is
enable/disable, after that the common PSR driver would call the encoder
registered callback to set the PSR state.
Fb driver would call the flush interface in 'fb->dirty' callback, this
helper function would force all PSR enabled encoders to exit from PSR
for 3 seconds.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
[seanpaul removed leftover psr_enabled/psr_work kruft from drm_vop.c]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
VOP have integrated a hardware counter which indicate the exact display
line that vop is scanning. And if we're interested in a specific line,
we can set the line number to vop line_flag register, and then vop would
generate a line_flag interrupt for it.
For example eDP PSR function is interested in the vertical blanking
period, then driver could set the line number to zero.
This patch have exported a symbol that allow other driver to listen the
line flag event with given timeout limit:
- rockchip_drm_wait_line_flag()
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
There are two VOP in rk3399 chip, respectively VOP_BIG and VOP_LIT.
most registers layout of this two vop is same, their framework are both
VOP_FULL, the Major differences of this two is that:
VOP_BIG max output resolution is 4096x2160.
VOP_LIT max output resolution is 2560x1600
VOP_BIG support four windows.
VOP_LIT only support two windows.
RK3399 vop register layout is similar with rk3288, so some feature
can reuse with rk3288.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Some new vop register support mask, bit[16-31] is mask,
bit[0-15] is value, the mask is correspond to the value.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
[seanpaul masked 'v' per tfiga's review comments]
Reviewed-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
No functional changes, sort the vop registers to make
code more readable.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
[seanpaul resolved conflict with name change from _3066 to _3036]
Reviewed-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
The drivers have to modify the atomic plane state during the prepare_fb
callback so they track allocations, reservations and dependencies for
this atomic operation involving this fb. In particular, how else do we
set the plane->fence from the framebuffer!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160818180017.20508-1-chris@chris-wilson.co.uk
Replace the use of drm_plane_helper_check_update() with
drm_plane_helper_check_state() since we have a plane state.
Rockchip looks to handling plane clipping rather well already
(unlikje most arm drm drivers) so there are no function changes
here.
Cc: Yao <mark.yao@rock-chips.com>
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1469549224-1860-8-git-send-email-ville.syrjala@linux.intel.com
The dma-mapping core and the implementations do not change the DMA
attributes passed by pointer. Thus the pointer can point to const data.
However the attributes do not have to be a bitfield. Instead unsigned
long will do fine:
1. This is just simpler. Both in terms of reading the code and setting
attributes. Instead of initializing local attributes on the stack
and passing pointer to it to dma_set_attr(), just set the bits.
2. It brings safeness and checking for const correctness because the
attributes are passed by value.
Semantic patches for this change (at least most of them):
virtual patch
virtual context
@r@
identifier f, attrs;
@@
f(...,
- struct dma_attrs *attrs
+ unsigned long attrs
, ...)
{
...
}
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
and
// Options: --all-includes
virtual patch
virtual context
@r@
identifier f, attrs;
type t;
@@
t f(..., struct dma_attrs *attrs);
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
Link: http://lkml.kernel.org/r/1468399300-5399-2-git-send-email-k.kozlowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Salter <msalter@redhat.com> [c6x]
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> [cris]
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> [drm]
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Fabien Dessenne <fabien.dessenne@st.com> [bdisp]
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> [vb2-core]
Acked-by: David Vrabel <david.vrabel@citrix.com> [xen]
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [xen swiotlb]
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [s390]
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no> [avr32]
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arc]
Acked-by: Robin Murphy <robin.murphy@arm.com> [arm64 and dma-iommu]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Suddenly everyone shows up with their trivial patch series!
- piles of if (!ptr) check removals from Markus Elfring
- more of_node_put fixes from Peter Chen
- make fbdev support really optional in all drivers (except vmwgfx),
somehow this fell through the cracks when we did all the hard prep work
a while ago. Patches from Tobias Jakobi.
- leftover patches for the connector reg/unreg cleanup (required that I
backmerged drm-next) from Chris
- last vgem fence patch from Chris
- fix up warnings in the new sphinx gpu docs build
- misc other small bits
* tag 'topic/drm-misc-2016-07-22' of git://anongit.freedesktop.org/drm-intel: (57 commits)
GPU-DRM-Exynos: Delete an unnecessary check before the function call "vunmap"
GPU-DRM-sun4i: Delete an unnecessary check before drm_fbdev_cma_hotplug_event()
drm/atomic: Delete an unnecessary check before drm_property_unreference_blob()
drm/rockchip: analogix_dp: add missing clk_disable_unprepare() on error
drm: drm_connector->s/connector_id/index/ for consistency
drm/virtio: Fix non static symbol warning
drm/arc: Remove redundant dev_err call in arcpgu_load()
drm/arc: Fix some sparse warnings
drm/vgem: Fix non static symbol warning
drm/doc: Spinx leftovers
drm/dp-mst: Missing kernel doc
drm/dp-mst: Remove tx_down_in_progress
drm/doc: Fix missing kerneldoc for drm_dp_helper.c
drm: Extract&Document drm_irq.h
drm/doc: document all the properties in drm_mode_config
drm/drm-kms.rst: Remove unused drm_fourcc.h include directive
drm/doc: Add kerneldoc for @index
drm: Unexport drm_connector_unregister_all()
drm/sun4i: Remove redundant call to drm_connector_unregister_all()
drm/ttm: Delete an unnecessary check before the function call "ttm_tt_destroy"
...
Add the missing clk_disable_unprepare() before return in the
error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Backmerge drm-next to be able to apply Chris' connector_unregister_all
cleanup (need latest i915 and sun4i state for that).
Also there's a trivial conflict in ttm_bo.c that git rerere fails to
remember.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Because we are using a custom crtc_state structure, we must override the
reset helper to allocate the correct amount of memory.
Cc: stable@vger.kernel.org
Fixes: 4e257d9eee ("drm/rockchip: get rid of rockchip_drm_crtc_mode_config")
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
The drm_gem_object_unreference_unlocked() function tests whether
its argument is NULL and then returns immediately.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
The priv->crtc_funcs[] array has ROCKCHIP_MAX_CRTC elements so > should
be >= here.
Fixes: 2048e3286f ('drm: rockchip: Add basic drm driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
When the input color format is YUV, we need to do some external scale
for CBCR. Like,
* In YUV420 data format:
cbcr_xscale = dst_w / src_w * 2;
cbcr_yscale = dst_h / src_h * 2;
* In YUV422 data format:
cbcr_xscale = dst_w / src_w * 2;
cbcr_yscale = dst_h / src_h;
* In YUV444 data format
cbcr_xscale = dst_w / src_w;
cbcr_yscale = dst_h / src_h;
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
The WIN0 of RK3036 VOP could support YUV data format, but driver
forget to add the uv_vir register field for it.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
This fixes the following sparse warnings:
drivers/gpu/drm/rockchip/rockchip_drm_fb.c:32:23: warning: symbol 'rockchip_fb_get_gem_obj' was not declared. Should it be static?
drivers/gpu/drm/rockchip/rockchip_drm_fb.c:315:24: warning: symbol 'rockchip_drm_framebuffer_init' was not declared. Should it be static?
drivers/gpu/drm/rockchip/rockchip_drm_fb.c:329:6: warning: symbol 'rockchip_drm_mode_config_init' was not declared. Should it be static?
Signed-off-by: John Keeping <john@metanate.com>
The drm_gem_object_unreference_unlocked() function tests whether
its argument is NULL and then returns immediately.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/b66399ed-278b-b85d-4a21-b34164936ef6@users.sourceforge.net
Please consider merging this tag, which contains the v4 misc fixes and add RK3399 eDP support patches[0] I sent on 2016-06-29, rebased onto v4.7-rc5.
* 'upstream/analogix-dp-20160705' of git://github.com/yakir-Yang/linux:
dt-bindings: analogix_dp: rockchip: correct the wrong compatible name
drm/rockchip: analogix_dp: introduce the pclk for grf
drm/bridge: analogix_dp: fix no drm hpd event when panel plug in
drm/rockchip: analogix_dp: update the comments about why need to hardcode VOP output mode
drm/rockchip: analogix_dp: correct the connector display color format and bpc
drm/bridge: analogix_dp: passing the connector as an argument in .get_modes()
drm/rockchip: analogix_dp: make panel detect to an optional action
drm/rockchip: analogix_dp: add rk3399 eDP support
drm/bridge: analogix_dp: some rockchip chips need to flip REF_CLK bit setting
drm/bridge: analogix_dp: correct the register bit define error in ANALOGIX_DP_PLL_REG_1
drm/rockchip: analogix_dp: split the lcdc select setting into device data
Currently enabling Rockchip DRM support automatically pulls
in fbdev dependency. However this dep is unnecessary since
DRM core already handles this for us (DRM_FBDEV_EMULATION).
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
John Keeping