When page pool is not enabled, its address value is still NULL and page
pool should not be accessed, so add a check for it.
Fixes: 850bfb912a ("net: hns3: debugfs add support dumping page pool info")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adjusts the string spaces of some parameters of tx bd info in
debugfs according to their maximum needs.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The specified buffer length for three debugfs files fd_tcam, uc and tqp
is not enough for their maximum needs, so this patch fixes them.
Fixes: b5a0b70d77 ("net: hns3: refactor dump fd tcam of debugfs")
Fixes: 1556ea9120 ("net: hns3: refactor dump mac list of debugfs")
Fixes: d96b0e5946 ("net: hns3: refactor dump reg of debugfs")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the width of packets number registers is 32 bits, they needs at most
10 characters for decimal data printing, but now the string spaces is not
enough, so this patch fixes it.
Fixes: e44c495d95 ("net: hns3: refactor queue info of debugfs")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, driver queries number of mac statistics before querying mac
statistics. As the number of mac statistics is a fixed value in firmware,
it is redundant to query this number everytime before querying mac
statistics, it can just be queried once in initialization process and
saved in device specifications.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since user may need to check the current configuration of the
interrupt coalesce, so add debugfs support for query this info.
Create a single file "coalesce_info" for it, and query it by
"cat coalesce_info", return the result to userspace.
For device whose version is above V3(include V3), the GL's register
contains usecs and 1us unit configuration. When get the usecs
configuration from this register, it will include the confusing unit
configuration, so add a GL mask to get the correct value, and add
a QL mask for the frames configuration as well.
The display style is below:
$ cat coalesce_info
tx interrupt coalesce info:
VEC_ID ALGO_STATE PROFILE_ID CQE_MODE TUNE_STATE STEPS_LEFT...
0 IN_PROG 4 EQE ON_TOP 0...
1 START 3 EQE LEFT 1...
rx interrupt coalesce info:
VEC_ID ALGO_STATE PROFILE_ID CQE_MODE TUNE_STATE STEPS_LEFT...
0 IN_PROG 3 EQE LEFT 1...
1 IN_PROG 0 EQE ON_TOP 0...
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new firmware supports to divides the whole multicast MAC address space
equally to functions of all PFs, and calculates the space size of each PF
according to its function number.
To support this feature, PF driver adds querying multicast MAC address
space size from firmware and limits used number according to space size.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there are two ways for PF to set the unicast MAC address space
size: specified by config parameters in firmware or set to default value.
That's mean if the config parameters in firmware is zero, driver will
divide the whole unicast MAC address space equally to 8 PFs. However, in
this case, the unicast MAC address space will be wasted a lot when the
hardware actually has less then 8 PFs. And in the other hand, if one PF has
much more VFs than other PFs, then each function of this PF will has much
less address space than other PFs.
In order to ameliorate the above two situations, introduce the third way
of unicast MAC address space assignment: firmware divides the whole unicast
MAC address space equally to functions of all PFs, and calculates the space
size of each PF according to its function number. PF queries the space size
by the querying device specification command when in initialization
process.
The third way assignment is lower priority than specified by config
parameters, only if the config parameters is zero can be used, and if
firmware does not support the third way assignment, then driver still
divides the whole unicast MAC address space equally to 8 PFs.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some required spaces to improve readability.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The type of tqp_vector->vector_irq is int, so modify its print format
to "%d".
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some local variable declarations are no need to add "static", so remove it.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The parameter cmd in function definition of hns3_dbg_bd_file_init and
hns3_dbg_common_file_init is used type u32, this patch uniforms them
in function declaration to type u32 too.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the cmd index is obtained in debugfs by comparing file names.
However, this method may cause errors when processing more complex file
names. So, change this method by saving cmd in private data and comparing
it when getting cmd index in debugfs for optimization.
Fixes: 5e69ea7ee2 ("net: hns3: refactor the debugfs process")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds support of dumping MAC umv counter in debugfs,
which will be helpful for debugging.
The display style is below:
$ cat umv_info
num_alloc_vport : 2
max_umv_size : 256
wanted_umv_size : 256
priv_umv_size : 85
share_umv_size : 86
vport(0) used_umv_num : 1
vport(1) used_umv_num : 1
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, the flow director counter is not enabled. To improve the
maintainability for chechking whether flow director hit or not, enable
flow director counter for each function, and add debugfs query inerface
to query the counters for each function.
The debugfs command is below:
cat fd_counter
func_id hit_times
pf 0
vf0 0
vf1 0
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently rx page will be reused to receive future packet when
the stack releases the previous skb quickly. If the old page
can not be reused, a new page will be allocated and mapped,
which comsumes a lot of cpu when IOMMU is in the strict mode,
especially when the application and irq/NAPI happens to run on
the same cpu.
So allocate a new frag to memcpy the data to avoid the costly
IOMMU unmapping/mapping operation, and add "frag_alloc_err"
and "frag_alloc" stats in "ethtool -S ethX" cmd.
The throughput improves above 50% when running single thread of
iperf using TCP when IOMMU is in strict mode and iperf shares the
same cpu with irq/NAPI(rx_copybreak = 2048 and mtu = 1500).
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when the packet or frag size is small, it causes both security and
performance issue. As dma can't map sub-page, this means some extra
kernel data is visible to devices. On the other hand, the overhead
of dma map and unmap is huge when IOMMU is on.
So add a queue based tx shared bounce buffer to memcpy the small
packet when the len of the xmitted skb is below tx_copybreak.
Add tx_spare_buf_size module param to set the size of tx spare
buffer, and add set/get_tunable to set or query the tx_copybreak.
The throughtput improves from 30 Gbps to 90+ Gbps when running 16
netperf threads with 32KB UDP message size when IOMMU is in the
strict mode(tx_copybreak = 2000 and mtu = 1500).
Suggested-by: Barry Song <song.bao.hua@hisilicon.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a debugfs interface for dumping ptp information, which
is helpful for debugging.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IMP(Intelligent Management Processor) firmware add a new feature to
handle and consolidate RAS information for new devices, NIC driver
only needs to query the reported RAS information. NIC driver adds
support for this feature.
Driver queries device capability to check whether IMP support this
feature, If yes, execute the new RAS processing branch.
In order to add a method to check whether PF supports imp-handle RAS
feature, add dumping this info in debugfs.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add debugfs support for vlan configuraion. create a single file
"vlan_config" for it, and query it by command "cat vlan_config",
return the result to userspace.
The new display style is below:
$ cat vlan_config
I_PORT_VLAN_FILTER: on
E_PORT_VLAN_FILTER: off
FUNC_ID I_VF_VLAN_FILTER E_VF_VLAN_FILTER PORT_VLAN_FILTER_BYPASS
pf off on off
vf0 off on off
FUNC_ID PVID ACCEPT_TAG1 ACCEPT_TAG2 ACCEPT_UNTAG1 ACCEPT_UNTAG2
pf 0 on on on on
vf0 0 on on on on
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Previously, with hardware limitation, the port VLAN filter are
effective for both PF and its VFs simultaneously, so a single
function is not able to enable/disable separately, and the VLAN
filter state is default enabled. Now some device supports each
function to bypass port VLAN filter, then each function can
switch VLAN filter separately. Add capability flag to check
whether the device supports modify VLAN filter state. If flag
on, user will be able to modify the VLAN filter state by ethtool
-K.
Furtherly, the default VLAN filter state is also changed
according to whether non-zero VLAN used. Then the device can
receive packet with any VLAN tag if only VLAN 0 used.
The function hclge_need_enable_vport_vlan_filter() is used to
help implement above changes. And the VLAN filter handle for
promisc mode can also be simplified by this function.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, all debugfs commands have been reconstructed, and the
debugfs file node cmd is useless. So remove this debugfs file node.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the debugfs command for serv info is implemented by
"echo xxxx > cmd", and record the inforamtion in dmesg. It's
unnecessary and heavy. To improve it, create a single file
"serv_info" for it, and query it by command "cat serv_info",
return the result to userspace, rather than record in dmesg.
The display style is below:
$ cat service_task_info
local_clock: [ 114.203321]
delta: 784(ms)
last_service_task_processed: 4294918512(jiffies)
last_service_task_cnt: 4
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the debugfs command for dump mac tnl status is
implemented by "echo xxxx > cmd", and record the information
in dmesg. It's unnecessary and heavy. To improve it, create
a single file "mac_tnl_status" for it, and query it by command
"cat mac_tnl_status", return the result to userspace, rather
than record in dmesg.
The display style is below:
$ cat mac_tnl_status
Recently generated mac tnl interruption:
[0111204.175437] status = 0x30
[0154120.329912] status = 0x30
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, user gets qset shaper parameters by implementing debugfs
command "echo dump qs shaper > cmd", this command will dump info in
dmesg. It's unnecessary and heavy.
As there is "tm_qset" file in tm directory for dump qset info, to
optimize these command, merge qset shaper parameters to tm_qset
file and use cat command to get them.
The display style is below:
$ cat tm_qset
ID MAP_PRI LINK_VLD MODE DWRR IR_B IR_U IR_S BS_B BS_S FLAG
0000 0 1 dwrr 100 150 7 0 5 20 0
0001 0 0 sp 0 150 7 0 5 20 0
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, user gets qos buffer config by implementing debugfs command
"echo dump qos buf cfg > cmd", this command will dump info in dmesg.
It's unnecessary and heavy.
To optimize it, create a single file "qos_buf_cfg" in tm directory
and use cat command to get info. It will return info to userspace,
rather than record in dmesg.
The display style is below:
$ cat qos_buf_cfg
tx_packet_buf_tc_0: 0x120
tx_packet_buf_tc_1: 0x120
tx_packet_buf_tc_2: 0x120
tx_packet_buf_tc_3: 0x120
tx_packet_buf_tc_4: 0x0
tx_packet_buf_tc_5: 0x0
tx_packet_buf_tc_6: 0x0
tx_packet_buf_tc_7: 0x0
......
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, user gets priority map by implementing debugfs command
"echo dump qos pri map > cmd", this command will dump info in dmesg.
It's unnecessary and heavy.
To optimize it, create a single file "qos_pri_map" in tm directory
and use cat command to get info. It will return info to userspace,
rather than record in dmesg.
The display style is below:
$ cat qos_pri_map
vlan_to_pri: 0
PRI TC
0 0
1 1
2 2
3 3
4 0
5 1
6 2
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, user gets pause config by implementing debugfs command
"echo dump qos pause cfg > cmd", this command will dump info in dmesg.
It's unnecessary and heavy.
To optimize it, create a single file "qos_pause_cfg" in tm directory
and use cat command to get info. It will return info to userspace,
rather than record in dmesg.
The display style is below:
$ cat qos_pause_cfg
pause_trans_gap: 0x7f
pause_trans_time: 0xffff
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, user gets tc schedule info by implementing debugfs command
"echo dump tc > cmd", this command will dump info in dmesg. It's
unnecessary and heavy.
To optimize it, create a single file "tc_sch_info" and use cat command
to get info. It will return info to userspace, rather than record in
dmesg.
The display style is below:
$ cat tc_sch_info
enabled tc number: 4
weight_offset: 14
TC MODE WEIGHT
0 dwrr 25
1 dwrr 25
2 dwrr 25
3 dwrr 25
4 dwrr 0
5 dwrr 0
6 dwrr 0
7 dwrr 0
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, user gets some tm info by implementing debugfs command
"echo dump tm > cmd", this command will dump info in dmesg. It's
unnecessary and heavy.
In addition, the info of this command mixes info of qset, priority,
pg and port. Qset and priority have their own command to get info of
themself, so can remove info of qset and priority from this command.
To optimize it, create two new files "tm_pg", "tm_port" in tm directory
and use cat command to separately get info of pg and port.
The display style is below:
$ cat tm_pg
ID PRI_MAP MODE DWRR C_IR_B C_IR_U C_IR_S C_BS_B C_BS_S ...
00 0x1f dwrr 1 75 9 0 31 20 ...
$ cat tm_port
IR_B IR_U IR_S BS_B BS_S FLAG RATE(Mbps)
75 9 0 31 20 1 200000
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the debugfs command for tm map is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create a single file
"tm_map" for it, and query it by command "cat tm_map",
return the result to userspace, rather than record in dmesg.
As user can't specify queue id in cat command, driver will return info
of all queue id.
The display style is below:
$ cat tm_map
queue_id qset_id pri_id tc_id
0000 0000 00 00
INDEX | TM BP QSET MAPPING:
0000 | 00000000:00000000:00000000:00000000:00000000:00000000:00000000
0256 | 00000000:00000000:00000000:00000000:00000000:00000002:00000000
0512 | 00000000:00000000:00000000:00000004:00000000:00000000:00000000
0768 | 00000000:00000008:00000000:00000000:00000000:00000000:00000000
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the debugfs command for fd tcam is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create a single file
"fd_tcam" for it, and query it by command "cat fd_tcam",
return the result to userspace, rather than record in dmesg.
The display style is below:
$ cat fd_tcam
read result tcam key x(31):
00000000
00000000
00000000
08000000
00000600
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
read result tcam key y(31):
00000000
00000000
00000000
f7ff0000
0000f900
00000000
00000000
00000000
00000000
00000000
00000000
00000000
0000fff8
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the debugfs command for queue info is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create two files
"rx_queue_info" and "tx_queue_info" for it, and query it
by command "cat rx_queue_info" and "cat tx_queue_info",
return the result to userspace, rather than record in dmesg.
The display style is below:
$ cat rx_queue_info
QUEUE_ID BD_NUM BD_LEN TAIL HEAD FBDNUM PKTNUM ...
0 0 0 0 0 0 0 ...
1 0 0 0 0 0 0 ...
2 0 0 0 0 0 0 ...
$ cat tx_queue_info
QUEUE_ID BD_NUM TC TAIL HEAD FBDNUM OFFSET PKTNUM ...
0 0 0 0 0 0 0 0 ...
1 0 0 0 0 0 0 0 ...
2 0 0 0 0 0 0 0 ...
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the debugfs command for queue map is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create a single file
"queue_map" for it, and query it by command "cat queue_map",
return the result to userspace, rather than record in dmesg.
The display style is below:
$ cat queue_map
local_queue_id global_queue_id vector_id
0 0 341
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the debugfs command for reg is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create some files
"bios_common/ssu/igu_egu/rpu/ncsi/rtc/ppp/rcb/tqp/mac" for it,
and query it by command "cat xxx", return the result to
userspace, rather than record in dmesg.
The display style is below:
$ cat bios_common
BP_CPU_STATE: 0x0
DFX_MSIX_INFO_NIC_0: 0xc000
DFX_MSIX_INFO_NIC_1: 0x0
DFX_MSIX_INFO_NIC_2: 0x0
DFX_MSIX_INFO_NIC_3: 0x0
DFX_MSIX_INFO_ROC_0: 0xc000
DFX_MSIX_INFO_ROC_1: 0x0
DFX_MSIX_INFO_ROC_2: 0x0
DFX_MSIX_INFO_ROC_3: 0x0
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the debugfs command for ncl config is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create a single file
"ncl_config" for it, and query it by command "cat ncl_config",
return the result to userspace, rather than record in dmesg.
The display style is below:
$cat ncl_config
offset | data
0x0000 | 0x00000028
0x0004 | 0x00000400
0x0008 | 0x08040201
0x000c | 0x00000000
0x0010 | 0x00040004
0x0014 | 0x00040004
0x0018 | 0x00000000
0x001c | 0x00000000
0x0020 | 0x00040004
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the debugfs command for m7 info is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create a single file
"imp_info" for it, and query it by command "cat imp_info",
return the result to userspace, rather than record in dmesg.
The display style is below:
$cat imp_info
offset | data
0x0000 | 0x00000000 0x00000000
0x0008 | 0x00000000 0x00000000
0x0010 | 0x00000000 0x00000001
0x0018 | 0x00000000 0x00000000
0x0020 | 0x00000000 0x00000000
0x0028 | 0x00000000 0x00000000
0x0030 | 0x00000000 0x00000000
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the debugfs command for reset info is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create a single file
"reset_info" for it, and query it by command "cat reset_info",
return the result to userspace, rather than record in dmesg.
The display style is below:
$cat reset_info
PF reset count: 0
FLR reset count: 0
GLOBAL reset count: 0
IMP reset count: 0
reset done count: 0
HW reset done count: 0
reset count: 0
reset fail count: 0
vector0 interrupt enable status: 0x1
reset interrupt source: 0x0
reset interrupt status: 0x0
RAS interrupt status:0x0
hardware reset status: 0x0
handshake status: 0x80
function reset status: 0x0
Change to the "hclge_show_rst_info" in the "hclge_reset_err_handle",
when the reset fails, display reset info immediately.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the debugfs command for intr is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create a single file
"interrupt_info" for it, and query it by command "cat interrupt_info",
return the result to userspace, rather than record in dmesg.
The display style is below:
$cat interrupt_info
num_nic_msi: 65
num_roce_msi: 65
num_msi_used: 2
num_msi_left: 128
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the debugfs command for loopback is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create a single file
"loopback" for it, and query it by command "cat loopback",
return the result to userspace, rather than record in dmesg.
The display style is below:
$ cat loopback
mac id: 0
app loopback: off
serdes serial loopback: off
serdes parallel loopback: off
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the debugfs command for mng tbl is implemented by
"echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create a single file
"mng_tbl" for it, and query it by command "cat mng_tbl",
return the result to userspace, rather than record in dmesg.
The display style is below:
$ cat mng_tbl
entry mac_addr mask ether mask vlan mask i_map ...
00 00:00:00:00:00:00 0 88cc 0 0000 1 0f ...
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the debugfs command for mac list info is implemented
by "echo xxxx > cmd", and record the information in dmesg. It's
unnecessary and heavy. To improve it, create two files "uc" and
"mc" under directory "mac_list" for it, and query mac list info
by "cat mac_list/uc" and "mac_list/mc", return the result to
userspace, rather than record in dmesg.
The display style is below:
$ cat mac_list/uc
UC MAC_LIST:
FUNC_ID MAC_ADDR STATE
pf 00:18:2d:00:00:71 ACTIVE
$ cat mac_list/mc
MC MAC_LIST:
FUNC_ID MAC_ADDR STATE
pf 01:80:c2:00:00:21 ACTIVE
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the debugfs command for bd info is implemented
by "echo xxxx > cmd", and record the information in dmesg.
It's unnecessary and heavy.
To improve it, add two debugfs directories "tx_bd_info" and
"rx_bd_info", and create a file for each queue under these
two directories, and query the bd info of specific queue by
"cat tx_bd_info/tx_bd_queue*" or "cat rx_bd_info/rx_bd_queue*",
return the result to userspace, rather than record in dmesg.
The display style is below:
$ cat rx_bd_info/rx_bd_queue0
Queue 0 rx bd info:
BD_IDX L234_INFO PKT_LEN SIZE...
0 0x0 60 60...
1 0x0 1512 1512...
$ cat tx_bd_info/tx_bd_queue0
Queue 0 tx bd info:
BD_IDX ADDRESS VLAN_TAG SIZE...
0 0x0 0 0...
1 0x0 0 0...
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the debugfs command for dev capability and dev spec
are implemented by "echo xxxx > cmd", and record the information
in dmesg. It's unnecessary and heavy. To improve it, create a
single file "dev_info" for them, and query them by command
"cat dev_info", return the result to userspace, rather than
record in dmesg.
The display style is below:
$cat dev_info
dev capability:
support FD: yes
support GRO: yes
support FEC: yes
support UDP GSO: no
support PTP: no
support INT QL: no
support HW TX csum: no
support UDP tunnel csum: no
support TX push: no
support imp-controlled PHY: no
support rxd advanced layout: no
dev spec:
MAC entry num: 0
MNG entry num: 0
MAX non tso bd num: 8
RSS ind tbl size: 512
RSS key size: 40
RSS size: 1
Allocated RSS size: 0
Task queue pairs numbers: 1
RX buffer length: 2048
Desc num per TX queue: 1024
Desc num per RX queue: 1024
Total number of enabled TCs: 1
MAX INT QL: 0
MAX INT GL: 8160
MAX TM RATE: 100000
MAX QSET number: 1024
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, each debugfs command needs to create a file to get
the information. To better support more debugfs commands, the
debugfs process is reconstructed, including the process of
creating dentries and files, and obtaining information.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only when RXD advanced layout is enabled, in some cases
(e.g. ip fragments), the checksum of entire packet will be
calculated and filled in the least significant 16 bits of
the unused addr field.
So refactor out the handling of RX completion checksum: adjust
the location of the checksum in RX descriptor, and use ptype table
to identify whether this kind of checksum is calculated.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver gets packet type by parsing the
L3_ID/L4_ID/OL3_ID/OL4_ID from RX descriptor, it's
time-consuming.
Now some new devices support RXD advanced layout, which combines
previous OL3_ID/OL4_ID to 8bit ptype field, so the driver gets
packet type by looking up only one table, and L3_ID/L4_ID become
reserved fields.
Considering compatibility, the firmware will report capability of
RXD advanced layout, the driver will identify and enable it by
default. This patch provides basic function: identify and enable
the RXD advanced layout, and refactor out hns3_rx_checksum() by
using ptype table to handle RX checksum if supported.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hao Chen