Commit Graph

61 Commits

Author SHA1 Message Date
Sujith Manoharan ac46ba4384 ath9k: Fix BTCOEX debugfs file usage
The debugfs file for dumping btcoex parameters unconditionally
assumes a MCI-based device. This will not work for older btcoex
chips. Fix this by branching out the routine into separate
functions.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-11-19 10:45:40 -05:00
Rajkumar Manoharan 4df50ca869 ath9k: Dump BTCOEX tuning parameters
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-10-29 15:30:35 -04:00
Rajkumar Manoharan e82cb03f5a ath9k: adjust WLAN and BT concurrent transmission
The simulataneous transmission of both WLAN and BT might cause
increase in power levels. To avoid regulatory violation, WLAN tx
power will be adjusted according to BT power index based on avaliability
of BT scheduling messages. WLAN tx power reduction might affect its
performance. So WLAN tx power is only be lowered when the signal strength
is good enough. Otherwise concurrent tx will be disabled and WLAN uses
it default power levels. Also concurrent tx is disabled whenever WLAN is
moving to off-channel which might be used by BT.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-10-29 15:19:27 -04:00
Mohammed Shafi Shajakhan be41b05202 ath9k: Ensure we set FTP_STOMP_LOW weight when WLAN is idle
When WLAN is idle ensure we downgrade to FTP_STOMP_LOW weight
(from STOMP_LOW) to provide more bandwidth for BT FTP profile.
WLAN's idleness can be estimated by taking into account of the
rx data packets and just ignore beacons, qos nullfunc etc.

Also update bt_wait_time even if the chip is in NETWORK SLEEP
mode. This should help BT throughput when WLAN is idle.

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-10-29 15:18:50 -04:00
Sujith Manoharan 750f32cf0a ath9k: Fix BT_OP_SCAN usage
BT_OP_SCAN is applicable only for pre-MCI WLAN/BT combo chips
and using it for MCI-based cards is incorrect. Fix this by
cleaning up its usage.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-10-19 15:53:01 -04:00
Sujith Manoharan 78b1775ba0 ath9k: Use a helper routine for MCI/FTP tuning
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-10-19 15:53:01 -04:00
Sujith Manoharan 5160b46f3e ath9k: Fix BTCOEX weight initialization
The WLAN/BT weights have to set correctly before BTCOEX
is initialized. Currently, this is not done for all chips
in the AR9003 family. This patch fixes this issue by setting
the weights in the init path. While at it, rename ar9462_wlan_weights
to mci_wlan_weights since it is common to both AR9462 and AR9565.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-09-28 13:54:10 -04:00
Bala Shanmugam 6a73f507cf ath9k: Enable MCI for AR9565
Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-09-28 13:54:07 -04:00
Mohammed Shafi Shajakhan 5418b0f0ad ath9k: update hw_timer_enabled to false when we stop generic timers
Update the 'hw_timer_enabled' to 'false' wherever we are stopping
hardware generic timers, excecpt the case where we start them
again immediately.

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-09-24 14:59:10 -04:00
Rajkumar Manoharan 8f176a3a16 ath9k: fill led_pin before drv_start
Ensure that led pin is filled and set to OFF before starting
the driver. With recent changes, drv_start is being called even
before led_init is being completed. This is causing led is always
OFF on driver load when the interface is UP. This patch splits the
led init and fills the led pin before register hw.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-09-24 14:59:07 -04:00
Sujith Manoharan 46025f5504 ath9k: Choose correct LED pin for AR9565
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-09-11 15:32:01 -04:00
Mohammed Shafi Shajakhan 94ae77ea46 ath9k: Fix BTCOEX timer triggering comparision
Its more correct to convert btcoex_period to 'us' while
comparing with btcoex_no_stomp which is in 'us'.
Did not find any functionality issues being fixed,
as the generic hardware timer triggers are usually
refreshed with the newer duty cycle.

Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-09-11 15:13:51 -04:00
Mohammed Shafi Shajakhan 5d9b6f2639 ath9k: Fix a crash in 2 WIRE btcoex chipsets
Generic timers for BTCOEX functionality is applicable
only for 3 WIRE BTCOEX (and MCI) chipsets.
Hence btcoex->no_stomp_timer is allocated only 3 WIRE
btcoex chipsets and in all the other cases its NULL.
Make sure we stop the generic timer only if
'btcoex->hw_timer_enabled' is true(only if its up and
running)

Fixes the following crash

	[68757.020454] BUG: unable to handle kernel NULL pointer dereference at 0000000c
	[68757.020916] IP: [<f9b055c3>] ath9k_hw_gen_timer_stop+0x13/0x80 [ath9k_hw]
	[68757.021251] *pde = 00000000
	[68757.024384] EIP: 0060:[<f9b055c3>] EFLAGS: 00010082 CPU: 0
	[68757.024384] EIP is at ath9k_hw_gen_timer_stop+0x13/0x80 [ath9k_hw]
	[68757.024384] EAX: d32d0000 EBX: d32d0000 ECX: 00000000 EDX: 00000000
	[68757.024384] ESI: e67c24c0 EDI: 00000296 EBP: e137be2c ESP: e137be20
	[68757.024384]  DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
	[68757.024384] CR0: 8005003b CR2: 0000000c CR3: 00b99000 CR4: 000407d0
	[68757.024384] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
	[68757.024384] DR6: ffff0ff0 DR7: 00000400
	[68757.024384] Process kworker/u:2 (pid: 8917, ti=e137a000 task=ea7a6860 task.ti=e137a000)
	[68757.024384] Stack:
	[68757.024384]  c06c4676 d32d0000 e67c24c0 e137be38 f81c9590 e67c1ca0 e137be40 f81c95d9
	[68757.024384]  e137be64 f81cd1c5 00000246 00000002 d32d0000 e67c05e0 e67c1ca0 e67c05e0
	[68757.024384]  00000000 e137beac f81cdfa0 e137be84 00000246 00000246 e67c1ca0 e67c1ca0
	[68757.024384] Call Trace:
	[68757.024384]  [<c06c4676>] ? _raw_spin_lock_irqsave+0x86/0xa0
	[68757.024384]  [<f81c9590>] ath9k_gen_timer_stop+0x10/0x40 [ath9k]
	[68757.024384]  [<f81c95d9>] ath9k_btcoex_stop_gen_timer+0x19/0x20 [ath9k]
	[68757.024384]  [<f81cd1c5>] ath9k_ps_restore+0x85/0x110 [ath9k]
	[68757.024384]  [<f81cdfa0>] ath9k_config+0x220/0x520 [ath9k]
	[68757.024384]  [<f81cd47d>] ? ath9k_flush+0x15d/0x1b0 [ath9k]
	[68757.024384]  [<f85c7ca5>] ieee80211_hw_config+0x135/0x2c0 [mac80211]
	[68757.024384]  [<f860e3c8>] ieee80211_dynamic_ps_enable_work+0x198/0x5f0 [mac80211]

Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-09-05 14:53:33 -04:00
Mohammed Shafi Shajakhan c32cdbd84f ath9k: Stop the BTCOEX timers before disabling BTCOEX
Its safe to stop the BTCOEX timers 'period_timer' and
'no_stomp_timer' before disabling BTCOEX. These timers
can call ath9k_hw_btcoex_enable (or) change the BT
stomp type if they seem to be running after we had
called ath9k_hw_btcoex_disable, which is obviously
not correct.

Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:38 -04:00
Mohammed Shafi Shajakhan dd89f05a75 ath9k: Fix MCI cleanup
We are doing MCI cleanup eventhough BTCOEX is not enabled
via module parameter. This means we do ath_mci_cleanup
though we skipped calling ath_mci_setup. Yet it does not
causes any issues now  as we free the DMA buffer allocated
only when it is allocated during ath_mci_setup.

Reviewed-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:37 -04:00
Rajkumar Manoharan 08d4df410a ath9k: fix power consumption on network sleep when BTCOEX is enabled
The chip is waken up for every 45ms in btcoex timer cycle to
for sharing the radio between BT and WLAN. Whenever the wlan
interface is in network sleep mode, do not schedule hw timers.
This could reduce power consumption on idle associated state.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:20 -04:00
Mohammed Shafi Shajakhan c11216d1f6 ath9k: Fix clearing of BTCOEX flags
BTCOEX flags are set/cleared by atomic operations.
We got to do the same in ath9k_btcoex_timer_resume,
while clearing those BTCOEX flags.

Acked-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-09 16:36:01 -04:00
Mohammed Shafi Shajakhan 812944891c ath9k_hw: make use of the wrapper to check for MCI init
ath9k_hw_mci_is_enabled wrapper also takes care of
ATH9K_HW_CAP_MCI being set for the AR9462 under test.

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-28 14:37:46 -04:00
Rajkumar Manoharan b98ccec0a4 ath9k_hw: remove p_data argument from ar9003_mci_state
As p_data is unuse, lets remove it from ar9003_mci_state.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-13 14:36:00 -04:00
Rajkumar Manoharan dfd0587a7d ath9k: keep btcoex period in milliseconds
btcoex periord is converted into micro seconds during initialization
and converted back to milli seconds while starting timer. As MCI code
handles btcoex period in msec, lets keep the btcoex timer in msec and
convert them into other form whenever needed.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-13 14:35:56 -04:00
Rajkumar Manoharan 6995fb805e ath9k: improve BT FTP/PAN performance
When BT FTP/PAN transmits while WLAN is idle, the one of 9462 chain
often picks up BT's tx signal and starts receiving. If the current
weight is set to be higher than BT tx, BT tx will be aborted and this
also degrades BT performance. Hence lower WLAN rx priority in this
case only when there are no WLAN traffic.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:30 -04:00
Sujith Manoharan e6930c4b32 ath9k: Use separate operational flags for BTCOEX
Also, use atomic operations to check the flags.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:26 -04:00
Rajkumar Manoharan 0466e2547d ath9k_hw: remove ATH_BTCOEX_CFG_MCI
AR9462 uses modified version of 3-Wire hw scheme for btcoex.
MCI itself is not a separate hw scheme but it aids to manage
multiple bt profiles. In ar9462, bt priority traffic is identified
by the number of bt profile types instead of gpio. So that this
patch removes MCI hw scheme.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:35:30 -04:00
Felix Fietkau 7b27ba4e9c ath9k: do not register LEDs on AR913x
LED support is typically handled via system GPIO on these platforms.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-16 14:19:28 -04:00
Sujith Manoharan bff2ec2b91 ath9k: Fix BTCOEX shutdown
Flush MCI profiles only if MCI is being actually used.
This fixes a panic on driver unload when non-MCI devices
are being used and btcoex_enable is set.

BUG: unable to handle kernel NULL pointer dereference at           (null)
IP: [<ffffffffa06296d2>] ath_mci_flush_profile+0x12/0x100 [ath9k]
Call Trace:
[<ffffffffa061befe>] ath9k_stop_btcoex+0x5e/0x80 [ath9k]
[<ffffffffa061ed57>] ath9k_stop+0xb7/0x230 [ath9k]
[<ffffffffa0533f30>] ieee80211_stop_device+0x50/0x180 [mac80211]
[<ffffffffa051f0cf>] ieee80211_do_stop+0x2af/0x6a0 [mac80211]
[<ffffffffa051f4da>] ieee80211_stop+0x1a/0x20 [mac80211]
[<ffffffff81365d96>] __dev_close_many+0x86/0xe0
[<ffffffff81365ee0>] dev_close_many+0xa0/0x110
[<ffffffff81366038>] rollback_registered_many+0xe8/0x260
[<ffffffff813661cb>] unregister_netdevice_many+0x1b/0x80
[<ffffffffa051e950>] ieee80211_remove_interfaces+0xd0/0x110 [mac80211]
[<ffffffffa050c133>] ieee80211_unregister_hw+0x53/0x120 [mac80211]
[<ffffffffa061d5a4>] ath9k_deinit_device+0x44/0x70 [ath9k]
[<ffffffffa062c1d4>] ath_pci_remove+0x54/0xa0 [ath9k]
[<ffffffff81267c46>] pci_device_remove+0x46/0x110
[<ffffffff8131021c>] __device_release_driver+0x7c/0xe0
[<ffffffff81310960>] driver_detach+0xd0/0xe0
[<ffffffff81310078>] bus_remove_driver+0x88/0xe0
[<ffffffff81311122>] driver_unregister+0x62/0xa0
[<ffffffff81268004>] pci_unregister_driver+0x44/0xc0
[<ffffffffa062c8b5>] ath_pci_exit+0x15/0x20 [ath9k]
[<ffffffffa063205d>] ath9k_exit+0x15/0x31 [ath9k]
[<ffffffff810b92cc>] sys_delete_module+0x18c/0x270
[<ffffffff814373dd>] ? retint_swapgs+0x13/0x1b
[<ffffffff8124828e>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[<ffffffff81437de9>] system_call_fastpath+0x16/0x1b

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-12 14:19:33 -04:00
Sujith Manoharan 9a15858f0c ath9k: Remove ATH9K_HW_CAP_MCI checks
With the ability to remove BTCOEX support at compile time,
these checks are no longer needed.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27 14:06:39 -05:00
Sujith Manoharan 64ab38df6e ath9k: Remove ATH_BTCOEX_CFG_NONE checks
Since BTCOEX code can be compiled out cleanly now,
remove these checks.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27 14:06:38 -05:00
Sujith Manoharan d68475de96 ath9k: Initialize BTCOEX scheme using a helper
Setting up the required scheme can be done as part of the
BTCOEX initialization path and it doesn't belong in
ath9k_hw_fill_cap_info() anyway.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27 14:06:35 -05:00
Sujith Manoharan 4daa7760e2 ath9k: Use CONFIG_ATH9K_BTCOEX_SUPPORT
This patch uses CONFIG_ATH9K_BTCOEX_SUPPORT to conditionally
compile btcoex-related code in the driver core.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27 14:06:35 -05:00
Sujith Manoharan c0ac53fa57 ath9k: Calculate ampdu limit using a helper
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27 14:06:34 -05:00
Sujith Manoharan 56ca0dba9d ath9k: Process BTCOEX interrupts using a helper
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27 14:06:34 -05:00
Sujith Manoharan df198b172f ath9k: Use proper start/stop routines for BTCOEX
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27 14:06:34 -05:00
Sujith Manoharan 5908120fdc ath9k: Move BTCOEX init/deinit functions to gpio.c
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27 14:06:33 -05:00
Felix Fietkau 8a30930563 ath9k_hw: make bluetooth coexistence support optional at compile time
Many systems (e.g. embedded systems) do not have wifi modules connected to
bluetooth modules, so bluetooth coexistence is irrelevant there. With the
addition of MCI support, ath9k picked up quite a bit of extra code that
can be compiled out this way.

This patch redefines ATH9K_HW_CAP_MCI and adds an inline wrapper for
querying the bluetooth coexistence scheme, allowing the compiler to
eliminate code that uses it, with only very little use of #ifdef.

On MIPS this reduces the total size for the modules by about 20k.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-12-19 14:46:55 -05:00
Joe Perches d2182b69dc ath: Convert ath_dbg(bar, ATH_DBG_<FOO>, to ath_dbg(bar, FOO
Add ATH_DBG_ to macros to shorten the uses and
reduce the line count.

Coalesce ath_dbg formats.
Add missing spaces to coalesced formats.
Add missing newline terminations to ath_dbg formats.
Align ath_dbg arguments where appropriate.
Standardize ath_dbg formats without periods.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-12-19 14:35:31 -05:00
Rajkumar Manoharan bc6d5c29af ath9k: Remove enabling btcoex from stomp type change
This patch removes btcoex_enable from stomp type change and let
it be called from callee functions that makes the code can be
reusable for MCI changes.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-17 15:43:54 -05:00
Rajkumar Manoharan 7dc181c273 ath9k: Add btcoex profile management support for AR9462
AR9462 chips have the capabilities to provoide bluetooth
profile information. For non-AR9462 btcoex chips, the BT
priority traffic was identified by periodically polling
the respective registers and updated dutycycle, stomptype,
etc. As AR9462 chip offers the BT profile informations,
let us make use of that to update aggregation limit,
dutycycle, stomptype and wieghtages.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-08 15:54:30 -05:00
Rajkumar Manoharan 423e38e807 ath9k: Rename AR9480 into AR9462
Renamed to be in sync with Marketing term and to avoid
confusion with other chip names.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14 14:48:23 -04:00
Felix Fietkau 72d874c67c ath9k_hw: make ath9k_hw_set_interrupts use ah->imask by default
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-11 16:41:25 -04:00
Mohammed Shafi Shajakhan 90826313fd ath9k/ath9k_htc: Fix PS wrappers for RF kill
ath9k_hw_gpio_get reads the GPIO in/out registers to get the status of
GPIO pins, so use PS wrappers

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-30 15:57:04 -04:00
Mohammed Shafi Shajakhan 79ac9b3033 ath9k: enable LED pin for AR946/8x chipsets
now the LED starts working for AR946/8x chipsets

Cc: "Balasubramanian, senthilkumar" <senthilb@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-16 16:45:35 -04:00
Rajkumar Manoharan b037b69326 ath9k: do not enable interrupt on set interrupt mask
At preset set_interrupt also enables interrupt after changing
mask. This is not necessary in all cases and also sometime it
breaks the assumption that interrupt was disabled. So let us
enable the interrupt explicity if it was disabled earlier.
This could also avoid unnecessary register ops and also helps
the follow up patch to have global ref count for interrupts ops.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-09 15:52:05 -04:00
Sujith Manoharan 5b68138e56 ath9k: Drag the driver to the year 2011
The Times They Are a-Changin'.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-19 13:54:05 -04:00
Vivek Natarajan a039a99349 ath9k: Use ps wrappers for btcoex logic.
Use ps wrappers before accessing hw registers in btcoex.

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-28 14:50:02 -04:00
Vivek Natarajan 978f78bf71 ath9k_hw: Move bt_stomp to hw from common.
Move bt_stomp to ath9k_hw and add its support for latest chipsets.

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-28 14:50:00 -04:00
Senthil Balasubramanian 353e5019e0 ath9k: Fix LED gpio for AR93xx chipsets.
The LED gpio is incorrectly programmed for AR9300 and so the led
is not working propelry. AR93xx uses gpio 10 for LED and not the
default.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25 14:50:17 -04:00
Vasanthakumar Thiagarajan 788f6875fc ath9k: Fix bug in configuring hw timer
Hw next tigger time is configured as current_tsf + (timer_period * 10) which
is wrong, it should be current_tsf + timer_period. The wrong hw timer configuration
would cause btcoex related issues.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25 14:50:16 -04:00
Felix Fietkau 6de66dd963 ath9k: add support for overriding LED pin and GPIO settings from platform data
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-30 14:15:15 -04:00
Senthil Balasubramanian 15178535ad ath9k: Fix incorrect GPIO LED pin for AR9485
AR9485 doesn't use the default GPIO pin for LED and GPIO 6 is actually
used for this.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-28 14:06:55 -05:00
Felix Fietkau 0cf55c21ec ath9k: use generic mac80211 LED blinking code
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-28 14:06:55 -05:00