Add comments describing how REG_RXFLTMAP0, REG_RXFLTMAP1 and REG_RXFLTMAP2
work.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Monitor mode is enabled by handling the filter flags we get from mac80211 in
rtl8xxxu_configure_filter() and writing them to the RCR register.
By handling the filters, we can also stop setting the BSSID filters in the
association event.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rtl8192cu driver doesn't read/write the REG_EFUSE_TEST register.
Neither does the rtl8188eu driver. Do it only for multifunc devices
RTL8723AU/RTL8723BU.
Signed-off-by: Jakub Sitnicki <jsitnicki@gmail.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This was a leftover from the vendor driver that was never utilized.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We need to reset the 8051 in order for it to launch the fw on the
rtl8192eu.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In rtl8xxxu_load_firmware() check the return value of kmemdup() and
error out with -ENOMEM in case of NULL to prevent a NULL pointer
dereference.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Split big conditional statement.
* Check (data.length <= CCP_MAX_OPTION_LENGTH) only once.
* Don't read ccp_option[1] if not initialised.
Reading uninitialised ccp_option[1] was harmless, because this could
only happen when data.length was 0 or 1. So even then, we couldn't pass
the (ccp_option[1] < 2 || ccp_option[1] > data.length) test anyway.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_GENEVE is built as a loadable module, and bnx2x is built-in,
we get this link error:
drivers/net/built-in.o: In function `bnx2x_open':
:(.text+0x33322): undefined reference to `geneve_get_rx_port'
drivers/net/built-in.o: In function `bnx2x_sp_rtnl_task':
:(.text+0x3e632): undefined reference to `geneve_get_rx_port'
This avoids the problem by adding a separate Kconfig symbol named
CONFIG_BNX2X_GENEVE that is only enabled when the code is
reachable from the driver.
This is the same trick that BNX2X does for VXLAN support, and
is similar to how I40E handles both.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 883ce97d25 ("bnx2x: Add Geneve inner-RSS support")
Acked-By: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Problem: When switching off VLAN offloading on an i350, the VLAN
interface gets unusable. For testing, set up a VLAN on an i350
and some remote machine, e.g.:
$ ip link add link eth0 name eth0.42 type vlan id 42
$ ip addr add 192.168.42.1/24 dev eth0.42
$ ip link set dev eth0.42 up
Offloading is switched on by default:
$ ethtool -k eth0 | grep vlan-offload
rx-vlan-offload: on
tx-vlan-offload: on
$ ping -c 3 -I eth0.42 192.168.42.2
[...works as usual...]
Now switch off VLAN offloading and try again:
$ ethtool -K eth0 rxvlan off
Actual changes:
rx-vlan-offload: off
tx-vlan-offload: off [requested on]
$ ping -c 3 -I eth0.42 192.168.42.2
PING 192.168.42.2 (192.168.42.2) from 192.168.42.1 eth0.42: 56(84) bytes of da
ta.
--- 192.168.42.2 ping statistics ---
3 packets transmitted, 0 received, 100% packet loss, time 1999ms
I can only reproduce it on an i350, the above works fine on a 82580.
While inspecting the igb source, I came across the code in igb_set_vmolr
which sets the E1000_VMOLR_STRVLAN/E1000_DVMOLR_STRVLAN flags once and
for all, and in all of the igb code there's no other place where the
STRVLAN is set or cleared. Thus, VLAN stripping is enabled in igb
unconditionally, independently of the offloading setting.
I compared that to the latest Intel igb-5.3.3.5 driver from
http://sourceforge.net/projects/e1000/ which in fact sets and clears the
STRVLAN flag independently from igb_set_vmolr in its own function
igb_set_vf_vlan_strip, depending on the vlan settings.
So I included the STRVLAN handling from the igb-5.3.3.5 driver into our
current igb driver and tested the above scenario again. This time ping
still works after switching off VLAN offloading.
Tested on i350, with and without addtional VFs, as well as on 82580
successfully.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A similar issue was addressed a few years ago in the following thread:
http://www.spinics.net/lists/netdev/msg245877.html
At that time there were concerns that removing this statement may cause other
side effects. However the submitter addressed those concerns. But the dialogue
went cold. We have a new case where a customers application is registering and
un-registering multicast addresses every few seconds. This is leading to many
"Link is Up" messages in the logs as a result of the
"netif_carrier_off(netdev)" statement called by igbvf_msix_other(). Also on
some kernels it is interfering with the bonding driver causing it to failover
and subsequently affecting connectivity.
The Sourgeforge driver does not make this call and is therefore not affected.
If there were any side effects I would expect that driver to also be affected.
I have tested re-loading the igbvf driver and downing the adapter with the PF
entity on the host where the VM has this patch. When I bring it back up again
connectivity is restored as expected. Therefore I request that this patch gets
submitted.
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for generic Tx checksums to the igbvf driver. It
turns out this is actually pretty easy after going over the datasheet as we
were doing a number of steps we didn't need to.
In order to perform a Tx checksum for an L4 header we need to fill in the
following fields in the Tx descriptor:
MACLEN (maximum of 127), retrieved from:
skb_network_offset()
IPLEN (maximum of 511), retrieved from:
skb_checksum_start_offset() - skb_network_offset()
TUCMD.L4T indicates offset and if checksum or crc32c, based on:
skb->csum_offset
The added advantage to doing this is that we can support inner checksum
offloads for tunnels and MPLS while still being able to transparently
insert VLAN tags.
I also took the opportunity to clean-up many of the feature flag
configuration bits to make them a bit more consistent between drivers. In
the case of the VF drivers this meant adding support for SCTP CRCs, and
inner checksum offloads for MPLS and various tunnel types.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for generic Tx checksums to the igb driver. It
turns out this is actually pretty easy after going over the datasheet as we
were doing a number of steps we didn't need to.
In order to perform a Tx checksum for an L4 header we need to fill in the
following fields in the Tx descriptor:
MACLEN (maximum of 127), retrieved from:
skb_network_offset()
IPLEN (maximum of 511), retrieved from:
skb_checksum_start_offset() - skb_network_offset()
TUCMD.L4T indicates offset and if checksum or crc32c, based on:
skb->csum_offset
The added advantage to doing this is that we can support inner checksum
offloads for tunnels and MPLS while still being able to transparently
insert VLAN tags.
I also took the opportunity to clean-up many of the feature flag
configuration bits to make them a bit more consistent between drivers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
E1000_MRQC_ENABLE_RSS_4Q enables 4 and 8 queues depending on the part
so rename to be generic.
Similarly, E1000_MRQC_ENABLE_VMDQ_RSS_2Q has no numeric meaning so
rename to be more generic.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In general case the maximum supported half cycle time of the synchronized
output clock is 70msec. Slower half cycle time than 70msec can be
programmed also as long as the output clock is synchronized to whole
seconds, useful specifically for generating a 1Hz clock.
Permitted values for the clock half cycle time are: 125,000,000 decimal,
250,000,000 decimal and 500,000,000 decimal (equals to 125msec, 250msec
and 500msec respectively).
Before this patch, only the half cycle time of less than or equal to 70msec
uses the I210 clock output function. This patch adds additional conditions
when half cycle time is equal to 125msec or 250msec or 500msec to use
clock output function.
Under other conditions, interrupt driven target time output events method
is still used to generate the desired clock output.
Signed-off-by: Roland Hii <roland.king.guan.hii@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Override EEPROM settings for specific OEM devices.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This e1000_phy_operations structure is never modified, so declare it as
const. Other structures of this type are already const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I210 device IPv6 autoconf test sometimes fails,
because DAD NS for link-local is not transmitted.
This packet is silently dropped.
This problem is seen only GbE environment.
igb_watchdog_task link up detection continues to the following process.
The following cases are observed:
1.PHY 1000BASE-T Status Register Remote receiver status bit is NG.
(NG status becomes OK after about 200 - 700ms)
2.In this case, the transfer packet is silently dropped.
1000BASE-T Status register
[Expected]: 0x3800 or 0x7800
[problem occurred]: 0x2800 or 0x6800
Frequency of occurrence: approx 1/10 - 1/40 observed
In order to avoid this problem,
wait until 1000BASE-T Status register "Remote receiver status OK"
After applying this patch, at least 400 runs succeed with no problems.
Signed-off-by: Takuma Ueba <t.ueba11@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i219 (4) and i219 (5) are the next LOM generations that will be
available on the next Intel platform (KabeLake).
This patch provides the initial support for the devices.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There have been bugs caused by HW ULP configuration settings not being
properly cleared after cable connect in V-Pro capable systems.
This caused HW to get out of sync occasionally.
The fix ensures that ULP settings are cleared in HW after
LAN cable re-connect.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on feedback from HW team, the configured value of the internal PHY
HW FIFO pointer gap was incorrect for non-gig speeds.
This patch provides the correct configuration.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several packet loss issues were reported for which the root cause for
them was an incorrect configuration of internal HW PHY clock gating
mechanism by SW.
This patch provides the correct mechanism.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to system level changes introduced in Skylake, ULP exit takes
significantly longer to occur. Therefore, driver must wait longer for.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Claudiu Manoil says:
====================
gianfar: xmit() improvements
Remove redundant operations, improve code locality and maintainability.
Thanks.
V2: Updated first patch to not touch existing wmb().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Timestamp BD status updates that can be merged into the
same "do_tstamp" block, no need for extra save/restore
to the BD area. The code is more readable too.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the mapping of the head BD before the mapping of fragments.
The TOE (h/w offload) decision logic block can be also moved up
(as the TOE flag belongs to the head BD), resulting in more
localized code (TOE logic vs BD mapping code blocks).
Note that, for this h/w, the R (status) bit for the head BD of a S/G
frame needs to be written last for a reliable transmission.
For the fragmented skb case, a local variable is used to temporarily
store the status info of the first BD, replacing a BD status read.
A merge of 2 "if(do_tstamp)" blocks was also possible.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It needs very similar workarounds to the one on BCM4707. It was tested
on D-Link DIR-885L home router.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde says:
====================
be2net patches
Please consider applying to net-next
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In QnQ configurations like Flex-10 where the VLANs are inserted by the
ASIC, on rare occasions the HW is encountering a scenario where the
final frame length ends to be greater than what the ASIC can support.
This is because when the TXULP pulls the TX WRB to check the length
of the frame to be transmitted it also adds the size of VLANs to be
inserted by the HW to the length of the frame indicated in the WRB,
which in some cases fails the range check. This causes a UE.
Avoid this by trimming the skb length to accommodate the VLAN insertion.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When 16-bit integers are loaded on CPUs with high order native
register sizes, the CPU could use some extra ops before using them.
And currently some of the frequently used fields in the driver like
the producer and consumer indices of the queues are declared as u16.
This patch declares such fields as u32. With this change we see the
64-byte packets per second numbers improve by about 4%.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck says:
====================
Flow dissector fixes and improvements
This patch series is meant to fix and/or improve a number of items within
the flow dissector code. The main change out of all of this is that IPv4
and IPv6 fragmentation should now be handled better than it was. As a
result we should see an improvement when handling things like IP fragment
reassembly as the skbs should now only have header data in the linear
portion of the buffer while the fragments will only hold payload data.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to try and pull the L4 header in if it is available in the first
fragment. As such add the flag to indicate we want to pull the headers on
the first fragment in.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPv6 parsing was using a local pointer when it could use the same
pointer as the IPv4 portion of the code since the key_addrs can support
both IPv4 and IPv6 as it is just a pointer.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flow dissector bits handling FCoE didn't bother to actually validate
that the space there was enough for the FCoE header. So we need to update
things so that if there is room we add the header and report a good result,
otherwise we do not add the header, and report the bad result.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out that for IPv4 we were reporting the ip_proto of the fragment,
and for IPv6 we were not. This patch updates that behavior so that we
always report the IP protocol of the fragment. In addition it takes the
steps of updating the payload offset code so that we will determine the
start of the payload not including the L4 header for any fragment after the
first.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the logic for the IPv4 parsing so that it is consistent
with how we handle IPv6. Specifically if we do not have the flow key
indicating we want the addresses we still may need to take a look at the IP
fragmentation bits and to see if we should stop after we have recognized
the L3 header.
Fixes: 807e165dc4 ("flow_dissector: Add control/reporting of fragmentation")
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jes Sorensen