Errors in protocol should be logged when the driver aborts operations.
If the driver can carry on and "humor" the device, then emitting
the message as debug output level is fine.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several error paths in bind/probe code will only emit
output using dev_dbg. But if we are going to fail the
bind/probe, emit related output with "err" priority.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no reason for preventing the creation and removal
of qmimux network interfaces when the underlying interface
is up.
This makes qmi_wwan mux implementation more similar to the
rmnet one, simplifying userspace management of the same
logical interfaces.
Fixes: c6adf77953 ("net: usb: qmi_wwan: add qmap mux protocol support")
Reported-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 134f98bcf1.
The r8153_mac_clk_spd() is used for RTL8153A only, because the register
table of RTL8153B is different from RTL8153A. However, this function would
be called when RTL8153B calls r8153_first_init() and r8153_enter_oob().
That causes RTL8153B becomes unstable when suspending and resuming. The
worst case may let the device stop working.
Besides, revert this commit to disable MAC clock speed down for RTL8153A.
It would avoid the known issue when enabling U1. The data of the first
control transfer may be wrong when exiting U1.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some messages are before calling register_netdev(), so replace
netif_err() with dev_err().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Return error code if autosuspend_en, eee_get, or eee_set don't exist.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
U1/U2 shoued be enabled for USB 3.0 or later. The USB 2.0 doesn't
support it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For runtime resuming, the RTL8153B may be resumed from the state
of power cut, when enabling the feature of UPS. Then, the PHY
would be reset, so it is necessary to be initailized again.
Besides, the USB_U1U2_TIMER also has to be set again, so I move
it from r8153b_init() to r8153b_hw_phy_cfg().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace r8153_patch_request() with rtl_phy_patch_request().
Replace r8153_pre_ram_code() with rtl_pre_ram_code().
Replace r8153_post_ram_code() with rtl_post_ram_code().
Add rtl_patch_key_set().
The new functions have an additional parameter. It is used to wait
the patch request command finished. When the PHY is resumed from
the state of power cut, the PHY is at a safe mode and the
OCP_PHY_PATCH_STAT wouldn't be updated. For this situation, it is
safe to set patch request command without waiting OCP_PHY_PATCH_STAT.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
It is unfortunate that we need to add a pointer to the driver context to
get back to the usbnet device, but the space will be reclaimed once
there are no more users of the old API left and we can remove the data
value and flag from the tasklet struct.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210130234637.26505-1-kernel@esmil.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pass through mode is to allow packets in MAP format to be passed
on to the stack. rmnet driver can be used to process and demultiplex
these packets.
Pass through mode can be enabled when the device is in raw ip mode only.
Conversely, raw ip mode cannot be disabled when pass through mode is
enabled.
Userspace can use pass through mode in conjunction with rmnet driver
through the following steps-
1. Enable raw ip mode on qmi_wwan device
2. Enable pass through mode on qmi_wwan device
3. Create a rmnet device with qmi_wwan device as real device using netlink
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/1611560015-20034-1-git-send-email-subashab@codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add qmimux interface sysfs file qmap/mux_id to show qmap id set
during the interface creation, in order to provide a method for
userspace to associate QMI control channels to network interfaces.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/can/dev.c
b552766c87 ("can: dev: prevent potential information leak in can_fill_info()")
3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
0a042c6ec9 ("can: dev: move netlink related code into seperate file")
Code move.
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
57ac4a31c4 ("net/mlx5e: Correctly handle changing the number of queues when the interface is down")
214baf2287 ("net/mlx5e: Support HTB offload")
Adjacent code changes
net/switchdev/switchdev.c
20776b465c ("net: switchdev: don't set port_obj_info->handled true when -EOPNOTSUPP")
ffb68fc58e ("net: switchdev: remove the transaction structure from port object notifiers")
bae33f2b5a ("net: switchdev: remove the transaction structure from port attributes")
Transaction parameter gets dropped otherwise keep the fix.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Initialize tasklet using tasklet_init() rather than open-coding it.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Conflicts:
drivers/net/can/dev.c
commit 03f16c5075 ("can: dev: can_restart: fix use after free bug")
commit 3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
Code move.
drivers/net/dsa/b53/b53_common.c
commit 8e4052c32d ("net: dsa: b53: fix an off by one in checking "vlan->vid"")
commit b7a9e0da2d ("net: switchdev: remove vid_begin -> vid_end range from VLAN objects")
Field rename.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RTL8156 sends notifications about every 32ms.
Only display/log notifications when something changes.
This issue has been reported by others:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1832472https://lkml.org/lkml/2020/8/27/1083
...
[785962.779840] usb 1-1: new high-speed USB device number 5 using xhci_hcd
[785962.929944] usb 1-1: New USB device found, idVendor=0bda, idProduct=8156, bcdDevice=30.00
[785962.929949] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[785962.929952] usb 1-1: Product: USB 10/100/1G/2.5G LAN
[785962.929954] usb 1-1: Manufacturer: Realtek
[785962.929956] usb 1-1: SerialNumber: 000000001
[785962.991755] usbcore: registered new interface driver cdc_ether
[785963.017068] cdc_ncm 1-1:2.0: MAC-Address: 00:24:27:88:08:15
[785963.017072] cdc_ncm 1-1:2.0: setting rx_max = 16384
[785963.017169] cdc_ncm 1-1:2.0: setting tx_max = 16384
[785963.017682] cdc_ncm 1-1:2.0 usb0: register 'cdc_ncm' at usb-0000:00:14.0-1, CDC NCM, 00:24:27:88:08:15
[785963.019211] usbcore: registered new interface driver cdc_ncm
[785963.023856] usbcore: registered new interface driver cdc_wdm
[785963.025461] usbcore: registered new interface driver cdc_mbim
[785963.038824] cdc_ncm 1-1:2.0 enx002427880815: renamed from usb0
[785963.089586] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected
[785963.121673] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected
[785963.153682] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected
...
This is about 2KB per second and will overwrite all contents of a 1MB
dmesg buffer in under 10 minutes rendering them useless for debugging
many kernel problems.
This is also an extra 180 MB/day in /var/logs (or 1GB per week) rendering
the majority of those logs useless too.
When the link is up (expected state), spew amount is >2x higher:
...
[786139.600992] cdc_ncm 2-1:2.0 enx002427880815: network connection: connected
[786139.632997] cdc_ncm 2-1:2.0 enx002427880815: 2500 mbit/s downlink 2500 mbit/s uplink
[786139.665097] cdc_ncm 2-1:2.0 enx002427880815: network connection: connected
[786139.697100] cdc_ncm 2-1:2.0 enx002427880815: 2500 mbit/s downlink 2500 mbit/s uplink
[786139.729094] cdc_ncm 2-1:2.0 enx002427880815: network connection: connected
[786139.761108] cdc_ncm 2-1:2.0 enx002427880815: 2500 mbit/s downlink 2500 mbit/s uplink
...
Chrome OS cannot support RTL8156 until this is fixed.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20210120011208.3768105-1-grundler@chromium.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In general, device drivers should not be enabled by default.
Fixes: 657bc1d10b ("r8153_ecm: avoid to be prior to r8152 driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210113144309.1384615-1-geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This commit enables the use of the r8153_ecm driver, introduced with
commit c1aedf015e ("net/usb/r8153_ecm: support ECM mode for
RTL8153") for the Lenovo Powered USB-C Hub (17ef:721e) based on the
Realtek RTL8153B chip.
This results in the following driver preference:
- if r8152 is available, use the r8152 driver
- if r8152 is not available, use the r8153_ecm driver
This is done to prevent the NIC from constantly sending pause frames
when the host system enters standby (fixed by using the r8152 driver
in "r8152: Add Lenovo Powered USB-C Travel Hub"), while still allowing
the device to work with the r8153_ecm driver as a fallback.
Signed-off-by: Leon Schuermann <leon@is.currently.online>
Tested-by: Leon Schuermann <leon@is.currently.online>
Link: https://lore.kernel.org/r/20210111190312.12589-3-leon@is.currently.online
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This USB-C Hub (17ef:721e) based on the Realtek RTL8153B chip used to
use the cdc_ether driver. However, using this driver, with the system
suspended the device constantly sends pause-frames as soon as the
receive buffer fills up. This causes issues with other devices, where
some Ethernet switches stop forwarding packets altogether.
Using the Realtek driver (r8152) fixes this issue. Pause frames are no
longer sent while the host system is suspended.
Signed-off-by: Leon Schuermann <leon@is.currently.online>
Tested-by: Leon Schuermann <leon@is.currently.online>
Link: https://lore.kernel.org/r/20210111190312.12589-2-leon@is.currently.online
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MSFT ActiveSync implementation requires that the size of the response for
incoming query is to be provided in the request input length. Failure to
set the input size proper results in failed request transfer, where the
ActiveSync counterpart reports the NDIS_STATUS_INVALID_LENGTH (0xC0010014L)
error.
Set the input size for OID_GEN_PHYSICAL_MEDIUM query to the expected size
of the response in order for the ActiveSync to properly respond to the
request.
Fixes: 039ee17d1b ("rndis_host: Add RNDIS physical medium checking into generic_rndis_bind()")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Link: https://lore.kernel.org/r/20210108095839.3335-1-andrey.zhizhikin@leica-geosystems.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When measuring the throughput (iperf3 + TCP) while routing on a
not-so-powerful device (Mediatek MT7621, 880MHz CPU), I noticed that I
achieved significantly lower speeds with QMI-based modems than for
example a USB LAN dongle. The CPU was saturated in all of my tests.
With the dongle I got ~300 Mbit/s, while I only measured ~200 Mbit/s
with the modems. All offloads, etc. were switched off for the dongle,
and I configured the modems to use QMAP (16k aggregation). The tests
with the dongle were performed in my local (gigabit) network, while the
LTE network the modems were connected to delivers 700-800 Mbit/s.
Profiling the kernel revealed the cause of the performance difference.
In qmimux_rx_fixup(), an SKB is allocated for each packet contained in
the URB. This SKB has too little headroom, causing the check in
skb_cow() (called from ip_forward()) to fail. pskb_expand_head() is then
called and the SKB is reallocated. In the output from perf, I see that a
significant amount of time is spent in pskb_expand_head() + support
functions.
In order to ensure that the SKB has enough headroom, this commit
increases the amount of memory allocated in qmimux_rx_fixup() by
LL_MAX_HEADER. The reason for using LL_MAX_HEADER and not a more
accurate value, is that we do not know the type of the outgoing network
interface. After making this change, I achieve the same throughput with
the modems as with the dongle.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20210106122403.1321180-1-kristian.evensen@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Aligning to tx_ndp_modulus is not sufficient because the next align
call can be cdc_ncm_align_tail, which can add up to ctx->tx_modulus +
ctx->tx_remainder - 1 bytes. This used to lead to occasional crashes
on a Huawei 909s-120 LTE module as follows:
- the condition marked /* if there is a remaining skb [...] */ is true
so the swaps happen
- skb_out is set from ctx->tx_curr_skb
- skb_out->len is exactly 0x3f52
- ctx->tx_curr_size is 0x4000 and delayed_ndp_size is 0xac
(note that the sum of skb_out->len and delayed_ndp_size is 0x3ffe)
- the for loop over n is executed once
- the cdc_ncm_align_tail call marked /* align beginning of next frame */
increases skb_out->len to 0x3f56 (the sum is now 0x4002)
- the condition marked /* check if we had enough room left [...] */ is
false so we break out of the loop
- the condition marked /* If requested, put NDP at end of frame. */ is
true so the NDP is written into skb_out
- now skb_out->len is 0x4002, so padding_count is minus two interpreted
as an unsigned number, which is used as the length argument to memset,
leading to a crash with various symptoms but usually including
> Call Trace:
> <IRQ>
> cdc_ncm_fill_tx_frame+0x83a/0x970 [cdc_ncm]
> cdc_mbim_tx_fixup+0x1d9/0x240 [cdc_mbim]
> usbnet_start_xmit+0x5d/0x720 [usbnet]
The cdc_ncm_align_tail call first aligns on a ctx->tx_modulus
boundary (adding at most ctx->tx_modulus-1 bytes), then adds
ctx->tx_remainder bytes. Alternatively, the next alignment call can
occur in cdc_ncm_ndp16 or cdc_ncm_ndp32, in which case at most
ctx->tx_ndp_modulus-1 bytes are added.
A similar problem has occurred before, and the code is nontrivial to
reason about, so add a guard before the crashing call. By that time it
is too late to prevent any memory corruption (we'll have written past
the end of the buffer already) but we can at least try to get a warning
written into an on-disk log by avoiding the hard crash caused by padding
past the buffer with a huge number of zeros.
Signed-off-by: Jouni K. Seppänen <jks@iki.fi>
Fixes: 4a0e3e989d ("cdc_ncm: Add support for moving NDP to end of NCM frame")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209407
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cdc_ncm driver passes network connection notifications up to
usbnet_link_change(), which is the right place for any logging.
Remove the netdev_info() duplicating this from the driver itself.
This stops devices such as my "TRENDnet USB 10/100/1G/2.5G LAN"
(ID 20f4:e02b) adapter from spamming the kernel log with
cdc_ncm 2-2:2.0 enp0s2u2c2: network connection: connected
messages every 60 msec or so.
Signed-off-by: Roland Dreier <roland@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201224032116.2453938-1-roland@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflict in CAN, keep the net-next + the byteswap wrapper.
Conflicts:
drivers/net/can/usb/gs_usb.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Starting with iOS 14 released in September 2020, connectivity using the
personal hotspot USB tethering function of iOS devices is broken.
Communication between the host and the device (for example ICMP traffic
or DNS resolution using the DNS service running in the device itself)
works fine, but communication to endpoints further away doesn't work.
Investigation on the matter shows that no UDP and ICMP traffic from the
tethered host is reaching the Internet at all. For TCP traffic there are
exchanges between tethered host and server but packets are modified in
transit leading to impossible communication.
After some trials Matti Vuorela discovered that reducing the URB buffer
size by two bytes restored the previous behavior. While a better
solution might exist to fix the issue, since the protocol is not
publicly documented and considering the small size of the fix, let's do
that.
Tested-by: Matti Vuorela <matti.vuorela@bitfactor.fi>
Signed-off-by: Yves-Alexis Perez <corsac@corsac.net>
Link: https://lore.kernel.org/linux-usb/CAAn0qaXmysJ9vx3ZEMkViv_B19ju-_ExN8Yn_uSefxpjS6g4Lw@mail.gmail.com/
Link: https://github.com/libimobiledevice/libimobiledevice/issues/1038
Link: https://lore.kernel.org/r/20201119172439.94988-1-corsac@corsac.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Avoid r8153_ecm is compiled as built-in, if r8152 driver is compiled
as modules. Otherwise, the r8153_ecm would be used, even though the
device is supported by r8152 driver.
Fixes: c1aedf015e ("net/usb/r8153_ecm: support ECM mode for RTL8153")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/1394712342-15778-394-Taiwan-albertk@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
LTE module MR400 embedded in TL-MR6400 v4 requires DTR to be set.
Signed-off-by: Filip Moc <dev@moc6.cz>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20201117173631.GA550981@moc6.cz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: ca139d76b0 ("cx82310_eth: re-enable ethernet mode after router reboot")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605247627-15385-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace usbnet_get_stats64() with new identical core function
dev_get_tstats64() in all users and remove usbnet_get_stats64().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use netdev->tstats instead of a member of usbnet for storing a pointer
to the per-cpu counters. This allows us to use core functionality for
statistics handling.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use netdev->tstats instead of a member of qmimux_priv for storing
a pointer to the per-cpu counters. This allows us to use core
functionality for statistics handling.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Grant Grundler