The fcf pointer is checked again after this verification
making the first check redundant. Remote the first check.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
fcoe_create exits using out_nodev label when module is not
yet LIVE but this exit path unlocks the rtnl_lock though
rtnl lock was not held in this case.
So this patch replaces out_nodev with out_nomod to exit
w/o unlocking rtnl_lock.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
After the recent patch "fixes unnecessary seq id jump"
the SCST module fcst stopped working because multi-sequence
write data wasn't finding the sequence after the first frame.
Add back the setting of the seq_id when the first frame arrives.
Also fix indentation on two lines.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
1) Allow transition to NEED RESET state only from READY state for ISP82xx.
2) Avoid infinite ISP aborts when chip reset fails.
3) Code cleanup to remove some of the unused debug code.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Santosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The problem occurring is a hw-race where there's an outstanding read-flash
operation occurring while the chip is being reset (done via an sg_reset script).
After the chip is paused, the read-flash operation never completes and the
DPC thread, while trying to complete the reset, is never able to recover,
as the HW appears to be hung...
The fix is to wait for outstanding flash operation prior to doing a sg_reset -h.
And to wait for reset to complete before any flash operations.
Note, during the wait, if any of the operation (reset/flash) does not complete,
failure is returned to the upper layer. The upper layer either need to
fail or retry.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The qla2xxx driver uses a port_id_t to mark the start of its enumerations. gcc
is complaining that wrap.b24 may be used uninitialized, but this doesn't look
to be possible. Silence it.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently we can only issue the task management (TM)
commands via the mailbox mechanism. This is a limitation,
since only one mailbox command can be issued at a time.
The purpose of this effort is to provide support for
issuing and processing the respose to TM and Marker
IOCBs asynchronously. Towards achieving this, the
consolidated srb architecture that is currently used for
BSG and IOCB/Logio commands has been enhanced and used.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently, BSG and IOCB/Logio commands have a different
framework (srb structs). The purpose of this effort is to
consolidate them into a generalized framework for these
as well as other asynchronous operations in the future.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Migrate to a consistent set of debug entries during status-IOCB
handling:
* group CS_TIMEOUT handling with CS_PORT_UNAVAILABLE and the like
(more regrouping of common behaviour).
* drop CS_DATA_OVERRUN handling as it now falls into the
'default' case (still returns DID_ERROR).
* consolidate CS_RESET and CS_ABORTED handling, as we the only
functional difference was a printk() (still returns DID_RESET).
* dropped all the earlier inconsistent [qla_]printk()s sprinkled
throught the needlessly large case-statement. Failure case
I/Os are now logged with a 'standard' format:
<command failure details>
<command generic details>
so, for example a dropped-frame is logged as:
qla2xxx 0000:13:00.0: scsi(16:0:0) Dropped frame(s) detected (4000 of 4000 bytes).
qla2xxx 0000:13:00.0: scsi(16:0:0) FCP command status: 0x15-0x18 (70018) \
oxid=78 ser=76 cdb=280000 len=4000 rsp_info=0 resid=0 fw_resid=4000
which should now convey all relevant information.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The driver should not be unloaded if any application is using it.
To disallow driver unload, driver use count must be incremented.
Application uses this char device as handle and increases driver
use count to avoid possible driver unload.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently error status is cleared only after the uncorrectable fatal errors
in the qla2xxx_pci_slot_reset. This fix is added to clear the error status in
qla2xxx_pci_resume. This way for both fatal and non-fatal errors the error
status gets cleared properly.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=572258
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
With qla2xxx using mid-layer async-scsi-scanning, the link state for
disconnected port is displayed wrong. Additional check for cable presence
is considered to display proper link state.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
commit 70b25f890c
Author: Tejun Heo <tj@kernel.org>
Date: Thu Apr 15 09:00:08 2010 +0900
[SCSI] fix locking around blk_abort_request()
Introduced a reference before check problem, fix this by moving the
lock shorthand code to be right at the point of actual use.
Reported-by: Dan Carpenter <error27@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
dev_node_t was only used to transport some minor/major numbers
from the PCMCIA device drivers to deprecated userspace helpers.
However, only a few drivers made use of it, and the userspace
helpers are deprecated anyways. Therefore, get rid of dev_node_t .
As a first step, remove any usage of dev_node_t from drivers which
only wrote to this typedef/struct, but did not make use of it.
CC: linux-bluetooth@vger.kernel.org
CC: Harald Welte <laforge@gnumonks.org>
CC: linux-mtd@lists.infradead.org
CC: linux-wireless@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-serial@vger.kernel.org
CC: alsa-devel@alsa-project.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Instead of the old pcmcia_request_irq() interface, drivers may now
choose between:
- calling request_irq/free_irq directly. Use the IRQ from *p_dev->irq.
- use pcmcia_request_irq(p_dev, handler_t); the PCMCIA core will
clean up automatically on calls to pcmcia_disable_device() or
device ejection.
- drivers still not capable of IRQF_SHARED (or not telling us so) may
use the deprecated pcmcia_request_exclusive_irq() for the time
being; they might receive a shared IRQ nonetheless.
CC: linux-bluetooth@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-serial@vger.kernel.org
CC: alsa-devel@alsa-project.org
CC: linux-usb@vger.kernel.org
CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
There's nastyness in the way we currently handle barriers (and
discards): They're effectively filesystem commands, but they get
processed as BLOCK_PC commands. Unfortunately BLOCK_PC commands are
taken by SCSI to be SG_IO commands and the issuer expects to see and
handle any returned errors, however trivial. This leads to a huge
problem, because the block layer doesn't expect this to happen and any
trivially retryable error on a barrier causes an immediate I/O error
to the filesystem.
The only real way to hack around this is to take the usual class of
offending errors (unit attentions) and make them all retryable in the
case of a REQ_HARDBARRIER. A correct fix would involve a rework of
the entire block and SCSI submit system, and so is out of scope for a
quick fix.
Cc: Hannes Reinecke <hare@suse.de>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Some arrays are giving I/O errors with ext3 filesystems when
SYNCHRONIZE_CACHE gets a UNIT_ATTENTION. What is happening is that
these commands have no retries, so the UNIT_ATTENTION causes the
barrier to fail. We should be enable retries here to clear any
transient error and allow the barrier to succeed.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
wd33c93_release() has been empty since ages, and sgiwd93.c no longer calls it
since its conversion to a proper platform driver 2 years ago. Also remove the
callers in the m68k wd33c93 shims.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
used cmd->host_scribble to store iocb command handle.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Per RFC 3720, Login Response Status Code 0x02 should not be retried.
Condensed connection error checking code to a single routine, and
added check for status class 0x02.
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Updated firmware ready timeout algorithm to prevent
long delays and use jiffies to time out instead of
counter. Also use msleep_interruptible instead of msleep.
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Link Down -> Mark all devices missing
Previously, the driver took no action on a Link Down,
and waited for the I/O on a dead connection to timeout
in the firmware before marking the DDB missing.
Link Up -> Mark all devices online
F/W will do auto login to all the devices only once.
After that its the responsibility of the driver to
relogin to devices whenever there is :
* Any sort of connection failure or
* KATO expires indicating target has logged out or
* I/O times out etc.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If cxgb3i_pdu_init() fails, then it appears that cxgb3i_iscsi_init()
will not be cleaned up, leading to the iscsi transport being left
registered. Fix this by adding a call to cxgb3i_iscsi_cleanup() on the
error path.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Karen Xie <kxie@chelsio.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In the scsi_debug driver, the virtual_gb option ignores the
sector_size, implicitly assuming that is 512 bytes. So if
'virtual_gb=1 sector_size=4096' the result is an 8 GB (virtual) disk.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This fixes a regression introduced with this commit:
commit d3305f3407
Author: Mike Christie <michaelc@cs.wisc.edu>
Date: Thu Aug 20 15:10:58 2009 -0500
[SCSI] libiscsi: don't increment cmdsn if cmd is not sent
in 2.6.32.
When I moved the hdr->cmdsn after init_task, I added
a bug when header digests are used. The problem is
that the LLD may calculate the header digest in init_task,
so if we then set the cmdsn after the init_task call we
change what the digest will be calculated by the target.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In the original code we dereferenced "pm8001_dev" before checking if it
was null. This patch moves the dereference inside the condition.
This was found by a static checker (smatch). I looked, but I couldn't
tell if "pm8001_dev" dev was ever actually null. The approach in this
patch seemed like the safest response.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If a command times out resulting in EH getting invoked, we wait for the
aborted commands to come back after sending the abort. Shorten
the amount of time we wait for these responses, to ensure we don't
get stuck in EH for several minutes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Commands which are completed by the VIOS are placed on a CRQ
in kernel memory for the ibmvfc driver to process. Each CRQ
entry is 16 bytes. The ibmvfc driver reads the first 8 bytes
to check if the entry is valid, then reads the next 8 bytes to get
the handle, which is a pointer the completed command. This fixes
an issue seen on Power 7 where the processor reordered the
loads from memory, resulting in processing command completion
with a stale handle. This could result in command timeouts,
and also early completion of commands.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch removes unnecessary #define's from hpsa. The SCSI midlayer
handles all this for us.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
blk_abort_request() expects queue lock to be held by the caller.
Grab it before calling the function.
Lack of this synchronization led to infinite loop on corrupt
q->timeout_list.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch fixes sdev_rw_attr() macro for scsi device sysfs entries.
It seems there is no such function snscanf in the current linux kernel,
so it fails to compile scsi driver when someone try to add a new rw entry.
This has been unfixed for a long time probably because current scsi device
has no rw entries.
# grep snscanf . -rn
./drivers/scsi/scsi_sysfs.c:489: snscanf (buf, 20, format_string, &sdev->field); \
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@jp.fujitsu.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix the compilation warning in powerpc. The same change also fixes endian
issue we found in powerpc test. This patch has been tested in x86 and
powerpc platform. it is created using scsi-misc-2.6.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Enhanced the driver to support new FCoE host bus adapter.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Error handling on advansys_board_found is fixed, because it's buggy in
the case we have an ASC_NARROW_BOARD set and failure happens on
AscInitAsc1000Driver step: it was freeing items of wrong struct in the
dvc_var union of struct asc_board, which could lead to an oops in the
case we set some of the fields in struct of narrow board as code was
choosing to always freeing wide board fields, and not everything was
being freed/released properly.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Various SCSI trace enhancements:
- Display data and protection information scatterlist lengths in the
trace output
- Add support for VERIFY and WRITE SAME commands and decode the UNMAP
bit if applicable
- Add decoding of the PROTECT field for READ/VERIFY/WRITE/WRITE SAME
commands as well as the EXPECTED INITIAL REFERENCE TAG field for
their 32-byte variants
- Decode READ CAPACITY(16), GET LBA STATUS, and UNMAP
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add a few clarifying comments in the B0 page function and allow the
optimal transfer length field to be specified on the command line using
opt_blks=N.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix operator precedence warning (from sparse), which results in the
data value always being 0:
drivers/scsi/qla4xxx/ql4_mbx.c:470:66: warning: right shift by bigger than source value
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Ravi Anand <ravi.anand@qlogic.com>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Cc: Karen Higgins <karen.higgins@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] bnx2i: Bug fixes related to MTU change issue when there are active iscsi sessions
[SCSI] ibmvscsi: fix DMA API misuse
[SCSI] wd7000: fix reset handler typo spin_unlock_irq() => spin_lock_irq()
[SCSI] zfcp: Fix tracing of requests with error status
[SCSI] zfcp: Update MAINTAINERS entry
[SCSI] iscsi_tcp: fix relogin/shutdown hang
[SCSI] qla2xxx: fix lock imbalance
[SCSI] lpfc: fix lock imbalances
[SCSI] be2iscsi: fix lock imbalance
[SCSI] dpt_i2o: several use after free issues
Define a new function to return the waitqueue of a "struct sock".
static inline wait_queue_head_t *sk_sleep(struct sock *sk)
{
return sk->sk_sleep;
}
Change all read occurrences of sk_sleep by a call to this function.
Needed for a future RCU conversion. sk_sleep wont be a field directly
available.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a bunch of fixes
1. Reduce sg table size to 64 (SG_MX) instead of default SG_ALL
2. clear task lists on phy down events
3. release all tasks on port deformation
4. release current task for device gone notification
5. Add sata abort handing
6. Add 10ms delay to each port reset (currently done serially and with
interrupts disabled)
[jejb: whitespace fixes and clean ups plus added description
added dummy 94xx_clear_srs_irq function just to prevent the
mismatch in the mvs_dispatch structure killing 94xx cards]
Signed-off-by: Srinivas <satyasrinivasp@hcl.in>
Cc: Andy Yan <ayan@marvell.com>
Cc: qswang@marvell.com
Cc: jfeng@marvell.com
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
iscsi_conn is not used so remove it from iscsi_sw_tcp_conn.
Signed-off-by: Avi Kaplan <savik751@gmail.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch changes the arguments to iscsi_sw_tcp_conn_restore_callbacks,
so that it works like the function to set the callbacks and because
in upcoming patches we need a iscsi_conn.
Signed-off-by: Avi Kaplan <savik751@gmail.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
blk_get_request sets the cmd_flags, so we should not and do not
need to set them. If we did set them to a different value then
it can cause a oops in the elevator code.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This change is basically a clean up.
datadgst_en is an int which comes from the user. I didn't see anything
limiting it to 1 and 0 although obviously that's what it's supposed to
be. If the user passed in 2 this test would fail.
This same if condition is repeated in another function and it uses &&
there.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Print all world wide node names (node, port and fabric) with the same
format specifier of "%16.16llx". That makes sure they all print as a
16 character hex string, with lower case letters, no 0x prefix, and
without stripping off any leading 0s.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Most of the prints of fabric IDs were specified as %6x, which will not
print any leading 0s. It's nice to see leading 0s for identifiers
like this, which are a fixed length. This patch sets the precision
modifier as well, making the specifier %6.6x, which forces the
printing of leading 0s.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
fc_fcp_resp is assuming when FCP_SNS_LEN_VAL is set, the FCP_RSP_LEN_VAL
is not, which is not true. This leads to not copying the sense data and
error out a valid FCP_RSP.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
No reason to restrict CDB size to 12 bytes in fcoe, so
increased to 16 so that 16 bytes SCSI CDB doesn't fail.
Uses common define to set max_cmd_len for fcoe and fnic,
fnic is already setting max_cmd_len to 16.
sg_readcap -l fails without this fix.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
fnic_flush_tx() is used to send frames held while fabric login
is in progress. The frames are held in tx_queue, but
fnic_flush_tx() was incorrectly flushing from recv_queue which
is used for received frames.
Signed-off-by: Brian Uchino <buchino@cisco.com>
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
New fnic version to mark inclusion of tx_flush bugfix.
Signed-off-by: Brian Uchino <buchino@cisco.com>
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
fc_exch_recv_req has variables eof, sof, and f_ctl,
which are set but never used. Delete them.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Allow for dormant states while link configuration completes.
In the default link mode, this is equivalent to the old check.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The FIP controler state wasn't being reset on a disable.
A disable/enable sequence should be treated as a link event.
Otherwise, when using disable to mask a time when the link
is up but unusable, FCF discovery would attempt to continue
and login would jump directly to the non-FIP fallback on
enable.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
FPMA indicates that the Fabric will provide the host's
N_Port's MAC address. When sending a FLOGI/FDISC frame
and FPMA was negotiated through FIP discovery we still
need to provide the MAC descriptor, as per the
specification, but the MAC should be zero'd out since
the FCF will be providing it in the FLOGI/FDISC ACC.
In FC-BB-5 section 7.8.7.4.2 (Fabric login) it states:
The MAC address field in the MAC address descriptor of a FIP FLOGI
Request operation or a FIP NPIV FDISC Request operation shall contain:
a) the proposed MAC address to use as VN_Port MAC address if the ENode
is requesting to use SPMA (see table 27);
b) all zeroes to indicate no MAC address is proposed if the ENode is
requesting to use FPMA (see table 27); or
c) the proposed MAC address to use as VN_Port MAC address if the ENode
supports both SPMA and FPMA and leaves the decision of which
addressing scheme to use to the FCF (i.e., if both the FP and SP
bits are set to one, see table 27).
This patch fixes case B.
This patch also adds debug statements to illustrate
whether a FPMA or SPMA MAC is added to a FLOGI/FDISC
frame.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix a oops in _scsih_sas_device_remove. The driver was attempting to
delete a object from the sas_device link list when the object was not
present.
Added sanity check for sas_device NULL dereference.
before deleting sas_device now driver will search device in list then
only it will follow device removal.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
we added support to set the deleted flag prior to device scan,
then clear the flag for responding devices, leaving the deleted flag only
set for missing devices. The problem is for internal generated host resets,
IO queues are not blocked at scsi mid layer level. IO will be continued
sent to driver, and driver will return SCSI_MLQUEUE_HOST_BUSY. The problem
is the driver checks for the deleted flag before it checks for the
controller being in reset, so there is a window where the driver would be
returning DID_NO_CONNECT for responding devices. This occurs during the
time between calling _scsih_prep_device_scan, and
_scsih_mark_responding_sas_device & _scsih_mark_responding_raid_device.
Fix the queuecommand entry point so ioc->shost_recovery flag sanity check is
given higher presidence then the device "deleted flag" check.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
bnx2i driver has to wait and cleanup all iscsi endpoints before
returning from bnx2i_stop(). This is to make sure all chip resources
are freed before chip is reset.
As the requirements for 1G and 10G chipsets is different, added
per-device 'hba_shutdown_tmo' parameter to adapter structure
If the connections are not torn down by the daemon within this timeout
period, 'cid's will be leaked in 10G device. 1G devices are more
flexible and do not leak any resources because the whole chip ports
gets reset when MTU is changed or ethtool selftest is run
fixed a minor issue in bnx2i_ep_poll() which unnecessarily forced
error return code when driver timed out waiting for TCP connect
request to complete
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add code to prevent unreg_vpi mailbox command from failing.
- Add code to reset the HBA if unreg_vpi mailbox fails with busy status.
- Remove code that was clearing the nlp_type stored during rport discovery.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add memcpy to mailbox completion to transfer reply correctly.
- Add support for BSG mailbox commands (dump, update_cfg, and
event_log_status).
- Add warning message and refuse mailbox command while mgmt is blocked.
- Add checks for memory allocation failure.
- Add check for sli4 dump zero BDE size.
- Only copy data if mailbox commands succeed.
- Add support for Read Event Log mailbox command.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Move the code to increase the sg seg count for LP21000 adapters.
- Check pcmd on command completion before dereferencing it.
- Clear queue memory when creating firmware queues to prevent stale entries.
- Replace the use of PAGE_SIZE in many areas that assumed it was always 4k.
- Add an else clause to a conditional that needed to unlock the hba_lock.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Update driver for change in T10-PI interface on adapter
- Remove Profiles.
- Add new SLI Opcodes.
- Add new PDE structures used for BlockGuard.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Prevent log message 1801 during vport delete.
- Enable NPIV by default.
- Display correct value for max Vports on SLI4 HBAs.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add the new Logical Link speed event support.
- Add RATOV and EDTOV to the REG_VFI mailbox command.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added check before free_pages just to make sure ioc->scsi_lookup is not NULL.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added support in the driver to support EEH and
PCIe Advanced Error Recovery. This involves adding new
pci_error_handler interface for recovering the controller from PCI Bus
errors, such as SERR and PERR. Some tools are available for simulating
PCI errors in order to validate this interface:
http://www.kernel.org/pub/linux/utils/pci/aer-inject
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
RAID_SCSI_IO_PASSTHROUGH: Driver needs to be sending the default
descriptor for RAID Passthru, currently its sending SCSI_IO descriptor.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
There are few special cases which needs to be handled deleting old port.
CASE1: In topology you need cascaded expanders. Through sysfs just make sure
topology is up. Erase the manufacturing image of the cascaded expander and
reset the board. In some cases Adapter will receive Exapnder Add event
before expander delete. In such a case, driver needs to delete duplicate
port before adding new port.
CASE2: Enable Device Missing delay of HBA through lsiutils. If expander or
end device is hotswapped with different device before DMD timer expires,
driver will get device add for new device first and then device deletion
event for the original devices will arrive later at DMD timer expires. In
this case also driver need to delete duplicate port before adding port for
new device.
Added new function which will make sure when new port is
added, that its not claiming the same phy resources already in use by
another port. If it does, then it will delete the other port before adding
the new port.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
While testing the midlevel q_at_head and q_at_tail
patch for sg and the block SG_IO ioctl I found it
useful to reduce the queuing within the scsi_debug
driver. The reason is that the midlevel queue only
comes into play when the corresponding LLD queue
is full.
It is also useful when testing to be confident that
your program is the only thing issuing commands
to the (virtual) scsi_debug device. The no_uld=1
parameter will stop a scsi_debug virtual disk
appearing as /dev/sd* .
Changelog:
- add max_queue parameter to reduce the number
of queued commands the driver will accept.
This parameter can be changed after the driver
is loaded.
- add no_uld parameter that restricts scsi_debug's
virtual devices to the sg and bsg drivers
- correct stale url
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
ibmvscsi uses dma_unmap_single() for buffers mapped via
dma_map_sg(). It works however it's the API violation. The DMA debug
facility complains about it:
http://marc.info/?l=linux-scsi&m=127018555013151&w=2
Reported-by: Sachin Sant <sachinp@in.ibm.com>
Tested-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This was introduced back in 2005 at the very start of the git era by:
df0ae2497d
[SCSI] allow sleeping in ->eh_host_reset_handler()
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Hazard testing uncovered yet another bug in sd. Under heavy reset
activity the retry counter might be exhausted and the command will be
returned with sense UNIT_ATTENTION/0x29/00 (POWER ON, RESET, OR BUS
DEVICE RESET OCCURRED). In those cases we should just increase the
retry counter again, retrying one more to clear up this Unit Attention
state.
[jejb: update to work with RC16 devices and not to loop endlessly]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When I made this patch:
b64e77f70b
it was to solve a problem where we were already on the waitqueue
becuase a connection problem/logout caused us to be on there
when we were cleaning up the session. If we happen to get
on queue for more normal reasons like their just does not happen
to be any send space at the same time we are closing the connection
we hit a race and get stuck in the wait.
We should not check if the waitqueue is active
because we could race with the network code. If
the network xmit code is just about to enter the
prepare to wait when we check for the waitqueue to
be active then we will miss each other and the
network code will fall into the wait and we will
not run wake_up.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
After Host Reset firmware will have new list of device handles for the target.
Device handle refresh in driver is part of Rescan topology logic.
(See functions like *_search_responding_*). This needs to be done from Host
Reset context before making shost_recovery to 0. Currently it is done in
Firwmare event context, which may leads IO to a wrong device.
Now handler refresh is moved to HBA reset context.
Apart from this, Now driver will stop IOs for all device setting deleted
flag to 1 at the time of HBA Reset through _scsih_prep_device_scan.
It will only unblock devices, if devices has been found as part of RESCAN.
This way it will make more safe IO blocking at the time of HBA reset at
mpt2sas driver layer.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
sd always tries to submit a READ_CAPACITY(16) CDB,
regardless whether the host actually supports it.
queuecommand() will then return DID_ABORT, which is
not qualified enough to detect the true cause here.
So better check in sd_try_rc16 first if the cdblen
is supported.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When bnx2/cnic/bnx2i drivers are loaded in certain order, bnx2i will
will not initialize the device correctly because 'hba->cnic' will be
NULL when bnx2i_start() is called from register_device() context.
Under this condition 'ifdown' and 'ifup' of associated network
interface is required to bring iscsi adapter state to ready state so
that it will accept iscsi connection setup within the chip
Initializing 'hba->cnic' before calling register_device() will fix
this issue
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
instruct firmware to use driver/iscsid provided expected statsn field
while constructing login pdu header.
Initialize 'flags' to instruct chip to use driver/iscsid provided
ExpStatSN value while constructing iSCSI login PDU header
Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If the scsi eh is running and then a FC LLD calls
fc_remote_port_delete, the SCSI commands sent from the eh will fail.
To prevent this, a FC LLD can call fc_block_scsi_eh from the eh
callback, blocking the eh thread until the dev_loss_tmo fires or the
remote port is available again.
If (e.g. for a multipathing setup) the dev_loss_tmo is set to a very
large value, thus preventing the scsi device removal , the scsi eh can
block for a long time. For multipathing, the fast_io_fail_tmo is then
set to a low value to detect path problems sooner.
This patch introduces a new return code FAST_IO_FAIL. The function
fc_block_scsi_eh now returns FAST_IO_FAIL when the fast_io_fail_tmo
fires. This indicates that the LLD terminated all pending I/O requests
and there are no more pending SCSI commands for the scsi eh to wait
for. This return code can be passed back to the scsi eh to stop the
escalation and finish the recovery process for this device.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The default is enabled since 7e47e5ca18.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The qla84xx_mgmt_cmd function supports multiple subcommands.
Some subcommands require DMA memory and some do not.
Therefore check before freeing DMA memory whether it is allocated or not.
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
1. Segregate BSG interface specific code to new files.
2. Handle multiple vendor specific commands indepedently.
3. Reorganised support for reset, management and update FCoE firmware commands.
4. Fixed memory leak issue in Loopback.
5. Added new vendor command to support iiDMA using BSG interface.
6. Proper cleanup of dma mapped and dma allocated buffers for BSG request.
[jejb: fix up conflict and merge in Jiri Slaby lock imbalance patch]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
sg address in IO request is not set up correctly for big endian platform.
add new macros to properly swap the address.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
idr is a global resource, protect it with global bfad_mutex.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Use pci_iomap() and pci_iounmap() to simplify the code. Remove uncessary #ifdef
check for ia64 (it was added as a workaound for some RHEL 5.x release which
doesn't export iounmap function)
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently the driver doesn't take into consideraion of possible sg chaining
when it walks through the sg list. This is fixed by using the sg_next()
which automatically handles the chaining case. Obosolete code is removed
as a result of this change.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Use duplicate fc transport template for physical and vitual port. Add
vport create/delete/disalbe functions in the transport template of physical
port. Changes to make the vport create/delete function to work under this
framework.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch (as1359) fixes a bug in scsi_alloc_target(). After a
device structure has been initialized (and especially after its name
has been set), it must not be freed directly. One has to call
put_device() instead.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch (as1358) fixes a bug in the error pathway of
scsi_target_add(). If registration fails, the target should not be
reaped. The reaping occurs later, when scanning is finished and all
the child devices are removed. The current code leaves an unbalanced
value in starget->reap_ref.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
RAID_SCSI_IO_PASSTHROUGH: Driver needs to be send the default
descriptor for RAID Passthru, currently its sending SCSI_IO descriptor.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added proper return type values in case memory allocation failed.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Removed all the mutex's for ioc->tm_cmds.mutex, then created one
single mutex inside the function mpt2sas_scsih_issue_tm. This is the
single function used when sending task management. Also the sanity
checks required for scsi mid layer escalation were moved to inside the
same function because these checks need to be done while the mutex is
held. The ioc->tm_cmds.mutex inside the IOCTL branch is really not
required since there is another mutex in this code called for ctl_cmds
handling this sync.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
1. Fixes for little endian issues.
2. Now Debug info for Discovery event is more readable.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Now Driver will not treat NEEDS_INIT as failure. In addition to this,
the driver will now display message to describe the the access flags
when bits are set, so the end user can better understand failures.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Aded checks for shost_recovery flag for early return from function.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
use the get_free_pages API for larger contigious physical memory chunk.
Also, the ioc->chain_depth need to be changed from
a 16bit to 32bit variable because the number of chains will exceed 64k
when the queue depth is large.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
bug fix in the handling of the internal device reset event
The reason code check in scsih_sas_device_status_change_event never
evaluates as true for internal device reset, hence driver never quiesce s IO
when firmware is sending a device reset. The fix is to change the
evaluate to:
if (event_data->ReasonCode !=
MPI2_EVENT_SAS_DEV_STAT_RC_INTERNAL_DEVICE_RESET &&
event_data->ReasonCode !=
MPI2_EVENT_SAS_DEV_STAT_RC_CMP_INTERNAL_DEV_RESET)
return;
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
incorrect timestamp on 32 bit platforms: The upper 32 bit of
the timestamp was getting truncated when converting seconds to
milliseconds, which was due to the variable being long. To fix the problem,
the variable needs to be u64. Also the microseconds conversion to
milliseconds was incorrect; it should be divide by 1000 instead of divide by
8.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Setting handle to zero is not required before _scsih_remove_device.
Driver uses sas_device->handle reference in _scsih_remove_device.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Enable NPIV by default.
- Added code to handle unsolicited LOGO on physical port.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Only abort outstanding I/O to force the OS to retry failed I/Os for AER
uncorrectable non-fatal errors instead of reseting the adapter.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add BSG support for PCI loopback testing.
- Add BSG support for extended mailbox commands.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Correct all SLI4 code to work on big endian systems.
- Move read of sli4 params earlier so returned values are used correctly.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
FCF failover improvements
- Add random FCF failover when there are multiple FCFs available.
- Prevent FCF log messages from being displayed for FC adapters.
- Separate the New FCF and Modified FCF log messages.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When the kernel is configured for preemption, using smp_processor_id()
when preemption is enabled causes a warning backtrace and is wrong
since we could move off of that CPU as soon as we get the ID,
and we would be referencing the wrong CPU, and possibly an invalid one
if it could be hotswapped out.
Remove the fc_lport_get_stats() function and explicitly use per_cpu_ptr()
to get the statistics. Where preemption has been disabled by holding
a _bh lock continue to use smp_processor_id(), but otherwise use
get_cpu()/put_cpu().
In fcoe_recv_frame() also changed the cases where we return in the
middle to do a goto to the code which bumps ErrorFrames and does
a put_cpu(). Two of these cases didn't bump ErrorFrames before, but
doing so is harmless because they "can't happen", due to prior length
checks.
Also rearranged code in fcoe_recv_frame() to have only one call to
fc_exch_recv(). It's just as efficient and saves a call to put_cpu().
In fc_fcp.c, adjusted a FIXME comment for code which doesn't need fixing.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
DID_ERROR cases can be ambigouos. Debugging FCP error cases
will be much easier if we have debug statements when we hit
these error conditions.
This patch simply adds debug messages using the FC_FCP_DBG
macro when we return DID_ERROR to SCSI. This way if a DID_ERROR
is reproducible turning on debug_logging will give a clue
to developers as to what the problem might be.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently fc_fcp_recv_data calls fc_fcp_retry_cmd to
retry failed IO but in this case tgt is still sending
data frames, therefore exchange needs to be aborted
first before initiating retry. So this patch fixes
this by aborting exchange first then have retry.
Renames fc_timeout_error to fc_fcp_recovery since
fc_timeout_error is already called from several other
places beside from fcp timeout handler and then
used fc_fcp_recovery for abort & retry from
fc_fcp_recv_data, this rename also required renaming
FC_CMD_TIME_OUT status to FC_CMD_RECOVERY to be
consistent with new fc_fcp_recovery.
Data frames are not expected for an DDPed exchange and
potentially it could be tampered data frame, so does
recovery in this case by calling fc_fcp_recovery.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Since use of offloads is more efficient than switching
to non-offload EM. However kept logic same to call em_match
if it is provided in the list of EMs.
Converted fc_exch_alloc to inline being now tiny a function
and already not an exported libfc API any more.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In some cases seq is incremented twice causing unnecessary
seq jump, for instance fc_exch_recv_seq_resp increments
seq id when fc_sof_is_init is true and that is true for
each incoming xfer ready but then fc_fcp_send_data does
another seq increment to send data for xfer ready.
This patch removes all such seq id jumps, at least it
eliminates few calls to fc_seq_start_next using ex_lock.
Also removes seq id update with incoming frame's seq id
as this is not needed since each end (I or T) just need
to send incremented their own seq id on each TSI from
other end & before sending new sequence within a
exchange.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When starting a new response sequence in a multi-sequence
exchange, a warning was issued that sequence initiative
wasn't held.
The bug was that sequence initiative was cleared by the previous
sequence due to the END_SEQ flag being on. The intent may have
been to check LAST_SEQ. Change just to check SEQ_INIT.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The link and last_link fields in the fcoe_ctlr struct are no
longer useful, since they are always set to the same value,
and FIP always calls libfc to pass link information to the lport.
Eliminate those fields and rename link_work to timer_work, since
it no longer has any link change work to do.
Thanks to Brian Uchino for discovering this issue.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Remove an unused variable, mac, in fcoe_recv_frame().
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The method we've been using for point-to-point mode requires
that the LS_ACC for the FLOGI uses the D_ID and S_ID assigned
to the remote port and local port, not those in the exchange.
This is not the correct method, but for now, it's what works
with the old target, as well as with new targets based on libfc.
This patch changes the addresses used accordingly.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When receiving a FLOGI request from a point-to-point peer,
the D_ID of 0xfffffe was not recognized as belonging to one
of the lports, so it was dropped.
Change fc_vport_id_lookup() to treat d_id 0xfffffe as a match.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In point-to-point mode, we need to save the source MAC
from received FLOGI requests to use as the destination MAC
for all outgoing frames. We stopped doing that at some point.
Use the lport_set_port_id method to catch incoming FLOGI frames
and pass them to fcoe_ctlr_recv_flogi() so it can save the source MAC.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The debug message that indicated we are using non-FIP mode was
being printed only if we were already in non-FIP mode.
Also changed the message text to make it more clear the mode
is being set, not that the message is indicating how FLOGI
was received.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In point-to-point mode, the destination MAC address for
the FLOGI response was zero because the LS_ACC for the FLOGI
wasn't getting intercepted by FIP.
Change to call fcoe_ctlr_els_send when sending any ELS,
not just requests.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In point-to-point mode, if the PLOGI to the remote port times
out, it can get deleted by the remote port module. Since there's
no reference by the local port, lport->ptp_data points to a freed
rport, and when the local port is reset and tries to logout again,
an oops occurs in mutex_lock_nested().
Hold a reference count on the point-to-point rdata.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Reduce indentation in fc_rport_recv_prli_req() using gotos.
Also add payload length checks.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch replaces incorrect base address space flag with correct IO
resource flag. Also, performs check of memory resource to validate
resource before using.
Signed-off-by: Richard A Lary <rlary@linux.vnet.ibm.com>
Acked-by: "Desai, Kashyap" <Kashyap.Desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The variable bfa_itnim is initialized twice to the same (side effect-free)
expression. Drop one initialization.
A simplified version of the semantic match that finds this problem is:
(http://coccinelle.lip6.fr/)
// <smpl>
@forall@
idexpression *x;
identifier f!=ERR_PTR;
@@
x = f(...)
... when != x
(
x = f(...,<+...x...+>,...)
|
* x = f(...)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Jing Huang <huangj@brocade.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
struct pmcraid_ioctl_header member buffer_length is unsigned, so this
check appears redundant.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Anil Ravindranath <anil_ravindranath@pmc-sierra.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This allows i == MAXHA, which is out of range
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The region set by the call to memset is immediately overwritten by the
subsequent call to memcpy.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2,e3,e4;
@@
- memset(e1,e2,e3);
memcpy(e1,e4,e3);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
external host not connecting after controller reboot: The
problem is : devices are not coming back after having the cable
disconnected then reconnected. The problem is because the
driver/firmware device removal handshake is failing. Due to this failure,
the controller firmware is not sending out device add events when the target
is reconnected. This is root caused to a race in the driver/firmware device
removal algorithm. There is duplicate code in both interrupt and user
context; where target reset is being issue from user context path while
sas_iounit_control(OP_REMOVE) is being sent from interrupt context. An
active target_reset will fail the OP_REMOVE. To fix this problem, the
duplicate code has been removed from user context path.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Upgraded version string.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
modified _scsih_sas_device_find_by_handle
so to handle the search on both list(device list and device_init_list)
Also, we moved the priority of the
search so the ioc->sas_device_list is done first. The
"sas_device_init_list" is only used during the 1st port enable, so its
unlikely there’s devices on it.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add the cancel_pending_work flag from the fw_event_work structure, and then to
set the flag during host reset, check the flag later from work threads
context and if cancel_pending_work_flag is set ingore those events.
Now Rescan after host reset is changed.
Added special task MPT2SAS_RESCAN_AFTER_HOST_RESET. This task will be queued
at the time of HBA reset. this task is treated as barrier. All work after
MPT2SAS_RESCAN_AFTER_HOST_RESET will be treated as new work and will be
server by callback handle. If host_recovery is going on while running RESCAN
task, it will wait for shos_recovery_done completion which will be called
from HBA reset DONE context.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The rport structure defines dev_loss_tmo as u32, which is
later multiplied with HZ to get the actual timeout value.
This might overflow for large dev_loss_tmo values. So we
should be better using u64 as intermediate variables here
to protect against overflow.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
scsi_dma_map() returns -1 if an error occurred (zero means that the
command has no data). So the following current code can't catch an
error:
sges_left = scsi_dma_map(scmd);
if (!sges_left) {
sdev_printk(KERN_ERR, scmd->device, "pci_map_sg"
" failed: request for %d bytes!\n", scsi_bufflen(scmd));
return -ENOMEM;
}
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: "Desai, Kashyap" <Kashyap.Desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This small patch forces 60 second timeouts for the older 3w-xxxx &
3w-9xxx drivers for systems that don't contain the udev rule for
setting scsi timeouts to 60 seconds.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: (34 commits)
cfq-iosched: Fix the incorrect timeslice accounting with forced_dispatch
loop: Update mtime when writing using aops
block: expose the statistics in blkio.time and blkio.sectors for the root cgroup
backing-dev: Handle class_create() failure
Block: Fix block/elevator.c elevator_get() off-by-one error
drbd: lc_element_by_index() never returns NULL
cciss: unlock on error path
cfq-iosched: Do not merge queues of BE and IDLE classes
cfq-iosched: Add additional blktrace log messages in CFQ for easier debugging
i2o: Remove the dangerous kobj_to_i2o_device macro
block: remove 16 bytes of padding from struct request on 64bits
cfq-iosched: fix a kbuild regression
block: make CONFIG_BLK_CGROUP visible
Remove GENHD_FL_DRIVERFS
block: Export max number of segments and max segment size in sysfs
block: Finalize conversion of block limits functions
block: Fix overrun in lcm() and move it to lib
vfs: improve writeback_inodes_wb()
paride: fix off-by-one test
drbd: fix al-to-on-disk-bitmap for 4k logical_block_size
...
Stanse found that one error path in qla24xx_bsg_timeout omits to
unlock ha->hardware_lock. Fix that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stanse found that two error paths in lpfc_bsg_rport_els_cmp and
lpfc_issue_ct_rsp_cmp omits to unlock phba->ct_ev_lock. It is
because they wrongly unlock phba->hbalock instead. Fix that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stanse found that one error path in mgmt_invalidate_icds omits to unlock
ctrl->mbox_lock. Fix that.
Added in 756d29c8c7 (Enable async mode for mcc rings)
where the spinlock was moved.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
adpt_i2o_delete_hba() calls kfree() so we have to save "pHba->next"
before calling it. Also inside adpt_i2o_delete_hba() itself, there
was another use after free bug which I fixed by moving the kfree()
down a line.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This was introduced back in 2005 at the very start of the git era by:
df0ae2497d
[SCSI] allow sleeping in ->eh_host_reset_handler()
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] qla1280: retain firmware for error recovery
[SCSI] attirbute_container: Initialize sysfs attributes with sysfs_attr_init
[SCSI] advansys: fix regression with request_firmware change
[SCSI] qla2xxx: Updated version number to 8.03.02-k2.
[SCSI] qla2xxx: Prevent sending mbx commands from sysfs during isp reset.
[SCSI] qla2xxx: Disable MSI on qla24xx chips other than QLA2432.
[SCSI] qla2xxx: Check to make sure multique and CPU affinity support is not enabled at the same time.
[SCSI] qla2xxx: Correct vp_idx checking during PORT_UPDATE processing.
[SCSI] qla2xxx: Honour "Extended BB credits" bit for CNAs.
[SCSI] scsi_transport_fc: Make sure commands are completed when rport is offline
[SCSI] libiscsi: Fix recovery slowdown regression
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
+little renaming of unicast functions to be smooth with multicast ones
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The qla1280 driver acquires its firmware via udev. During boot the firmware
is located in the initrd. If, after root is mounted, the adapter needs to
reload firmware (host reset), the firmware load may fail if the root device
is on the adapter being reset. This patch modifies qla1280 to retain the
firmware loaded via the initial request_firmware() for use during error
recovery.
[jejb: fix up checkpatch issues]
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
On newer kernels users of advansys module are reporting system hang when
trying to load it without firmware files present. After looking closely
at description on https://qa.mandriva.com/show_bug.cgi?id=53220, I think
this is related to commit "[SCSI] advansys: use request_firmware". The
problem is that after switch to request_firmware, asc_dvc->err_code
isn't being set when firmware files aren't found or loading fails.
err_code is used by the driver to judge if there was a fatal error or
not, as can be seen for example on advansys_board_found, which will only
return -ENODEV when err_code is set. Because err_code isn't being set
when request_firmware fails, this is a change of behaviour of the code
before request_firmware addition, making it continue to load and it
fails later as the firmware wasn't really loaded.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The fix prevents application path from sending get-firmware-state mbx command
during as isp reset.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
On specific platforms, MSI is unreliable on some of the QLA24xx chips, resulting
in fatal I/O errors under load, as reported in <http://bugs.debian.org/572322>
and by some RHEL customers.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The logic is changed to detect this condition based on following
1) both module parameters are off (ql2xmaxqueues and ql2xmultique_tag).
2) both module parameters are on (ql2xmaxqueues and ql2xmultique_tag).
3) The HBA does not support multi queue.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Checks should only be done for NPIV-capable ISPs. Original code
could result in PORT_UPDATEs being missed on non-NPIV-capable
ISPs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We now enable/disable "Additional Receive Credits" in f/w based on nvram
parameter "Extended_BB_Credits" bit (i.e. Enhanced-Features: at offset 0x196).
This is applicable only for GEN2 CNAs.
Signed-off-by: Santosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
blk_end_request doesn't complete a bidi request
successfully
The unfinished request eventually triggers a panic in
timeout handling routine fc_bsg_job_timeout as
req->special is NULL
Use blk_end_request_all to end the request unconditionally
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We could be failing/stopping a connection due to libiscsi starting
recovery/cleanup, but the xmit path or scsi eh thread path
could be dropping the connection at the same time.
As a result the session->state gets set to failed instead of in
recovery. We end up not blocking the session
and so the replacement timeout never gets started and we only end up
failing the IO when scsi_softirq_done sees that the
cmd has been running for (cmd->allowed + 1) * rq->timeout secs.
We used to fail the IO right away so users are seeing a long
delay when using dm-multipath. This problem was added in
2.6.28.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (69 commits)
[SCSI] scsi_transport_fc: Fix synchronization issue while deleting vport
[SCSI] bfa: Update the driver version to 2.1.2.1.
[SCSI] bfa: Remove unused header files and did some cleanup.
[SCSI] bfa: Handle SCSI IO underrun case.
[SCSI] bfa: FCS and include file changes.
[SCSI] bfa: Modified the portstats get/clear logic
[SCSI] bfa: Replace bfa_get_attr() with specific APIs
[SCSI] bfa: New portlog entries for events (FIP/FLOGI/FDISC/LOGO).
[SCSI] bfa: Rename pport to fcport in BFA FCS.
[SCSI] bfa: IOC fixes, check for IOC down condition.
[SCSI] bfa: In MSIX mode, ignore spurious RME interrupts when FCoE ports are in FW mismatch state.
[SCSI] bfa: Fix Command Queue (CPE) full condition check and ack CPE interrupt.
[SCSI] bfa: IOC recovery fix in fcmode.
[SCSI] bfa: AEN and byte alignment fixes.
[SCSI] bfa: Introduce a link notification state machine.
[SCSI] bfa: Added firmware save clear feature for BFA driver.
[SCSI] bfa: FCS authentication related changes.
[SCSI] bfa: PCI VPD, FIP and include file changes.
[SCSI] bfa: Fix to copy fpma MAC when requested by user space application.
[SCSI] bfa: RPORT state machine: direct attach mode fix.
...
This flag is not used, so best discarded.
Signed-off-by: NeilBrown <neilb@suse.de>
--
Hi Jens,
I came across this recently - these are the only two occurances
of "GENHD_FL_DRIVERFS" in the kernel, so it cannot be needed.
NeilBrown
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
There was a problem introduced in Jul 2008 by:
0e6f9d2708 pcmcia: use pcmcia_loop_config in scsi pcmcia drivers
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (56 commits)
doc: fix typo in comment explaining rb_tree usage
Remove fs/ntfs/ChangeLog
doc: fix console doc typo
doc: cpuset: Update the cpuset flag file
Fix of spelling in arch/sparc/kernel/leon_kernel.c no longer needed
Remove drivers/parport/ChangeLog
Remove drivers/char/ChangeLog
doc: typo - Table 1-2 should refer to "status", not "statm"
tree-wide: fix typos "ass?o[sc]iac?te" -> "associate" in comments
No need to patch AMD-provided drivers/gpu/drm/radeon/atombios.h
devres/irq: Fix devm_irq_match comment
Remove reference to kthread_create_on_cpu
tree-wide: Assorted spelling fixes
tree-wide: fix 'lenght' typo in comments and code
drm/kms: fix spelling in error message
doc: capitalization and other minor fixes in pnp doc
devres: typo fix s/dev/devm/
Remove redundant trailing semicolons from macros
fix typo "definetly" -> "definitely" in comment
tree-wide: s/widht/width/g typo in comments
...
Fix trivial conflict in Documentation/laptops/00-INDEX
The few lines below the kfree of hdr_buf may go to the label err_free
which will also free hdr_buf. The most straightforward solution seems to
be to just move the kfree of hdr_buf after these gotos.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier E;
expression E1;
iterator I;
statement S;
@@
*kfree(E);
... when != E = E1
when != I(E,...) S
when != &E
*kfree(E);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
qlogicpti driver registers its irq with a name containing slash.
This results in
[ 71.049735] WARNING: at fs/proc/generic.c:316 __xlate_proc_name+0xa8/0xb8()
[ 71.132815] name 'Qlogic/PTI'
because proc_mkdir with the name of the irq fails. Fix it by just
removing the slash from irq name. Discovered and tested on real hardware
(Sun Ultra 1).
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue occur while deleting 60 virtual ports through the sys
interface /sys/class/fc_vports/vport-X/vport_delete. It happen while in
a mistake each request sent twice for the same vport. This interface is
asynchronous, entering the delete request into a work queue, allowing
more than one request to enter to the delete work queue. The result is a
NULL pointer. The first request already delete the vport, while the
second request got a pointer to the vport before the device destroyed.
Re-create vport later cause system freeze.
Solution: Check vport flags before entering the request to the work queue.
[jejb: fixed int<->long problem on spinlock flags variable]
Signed-off-by: Gal Rosen <galr@storwize.com>
Acked-by: James Smart <james.smart@emulex.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
A pointer to a probe callback is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Cc: Henrik Kretzschmar <henne@nachtwindheim.de>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: peter fuerst <post@pfrst.de>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Upgrade the upstream driver from 2.0.0.0 to 2.1.2.1.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When IO is completed with underrun and with good SCSI status, check if
the transferred bytes against scsi_cmnd->underflow, which is set to
minimum number of bytes that must be transferred for this command, if
is less than required minimum, complete the IO with DID_ERROR.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
MS module did not invoke fdmi offline in all cases,
call fdmi offline when ms module receives a port offline,
so that fdmi offline is from one place in the ms module.
Make changes to handle 10G speed in the conversion routine.
Replaced the usage of bfa_adapter_attr_s struct with specific API's.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Modified the portstats get/clear logic for port physical/FCoE/QoS stats.
Added more stats to FC
Fixed some issues with FCoE stats collection.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
bfa_ioc_attr_s is a big structure and some times could cause
stack overflow if defined locally, so add specific APIs that
are needed to replace the use of ioc_attr local var.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Rename pport structures to fcport in BFA FCS, to resolve confusion
about the port structures in the firmware, and make sure the SG page
is setup correctly.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently BFA was not checking for IOC down condition when issuing
getstats/clearstats
Add check to see if IOC is operational, before issuing
getstats/clearstats.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Use dummy interrupt handlers till chip initialization is complete.
Install real interrupt handlers after chip initialization.
Also removed msix installation code in bfa_iocfc_init().
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fixed the issue of not acknowledging the command queue
full-to-non-full interrupt. Implemented separate acknowledging
functions for different ASIC and interrupt mode.
Fixed the case of missing CPE interrupt by always processing the
pending requests in the completion path.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
ioc_recover failed to work in fcmode.
Fixed the code to initialize the ioc_regs.err_set during the
notify_hbfail.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Replace enum types with int and rearrange the fields to fix some
alignment issue.
Local var ioc_attr is causing the stack to overflow, so removed the
usage of the local ioc_attr var and now invoking an API to return the
ioc_type.
Fix some AEN issues.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Introduce a link notification state machine to handle next incoming
link events while the current event is being delivered to the driver.
When the event has been processed by the driver, the link notification
state machine will queue the next event (if there is any) to the
driver.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Made FCS authentication related changes to state machines and header
files.
Made changes in FCS state machines to handle the case when secret
string is NULL.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Changed PCI VPD to incorporate specific OEM vendors.
Added FCoE specific interrupt latency and delay params.
Added some variables needed by FIP 2.0.
Added some new logging and tracing definitions.
Added reserved members to make the structures (IOC, IOCFC) 64bit aligned.
Changed the module identifiers, as some files were moved.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Copy fpma MAC when requested by user space application. Added FPMA
mac address to the lport attributes structure.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Make sure that in direct attach mode, we do not query the name server
after a target is marked offline.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Replace bfa_assert() with bfa_sm_fault() to get unhandled events for
debugging.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Clear LL_HALT and PSS_ERR bit in the interrupt status register on an IOC crash.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add support for faster IOC recovery after failure.
Split bfa_ioc.c into three files:
bfa_ioc.c: Common code shared between crossbow and catapult ASIC's.
bfa_ioc_cb.c: Code specific to the crossbow, reg mapping and
interrupt related routines.
bfa_ioc_ct.c: Code specific to the catapult, reg mapping and
interrupt related routines.
Fix to make sure IOC reinitialize's properly on enable request -
update the ioc_fwstate reg with BFI_IOC_FAIL on ioc disable mbox cmd
timeout.
Makefile changes to support the 2 newly added files bfa_ioc_cb.c and
bfa_ioc_ct.c.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
bfad.c & bfad_drv.h:
* Created a kernel thread from pci_probe that does the bfad start
operations after BFA init done on a firmware mismatch.
* The kernel thread on a fw mismatch waits for an event from IOC
call back and is woken up from bfa_cb_init() on BFA init success.
* In normal cases of no firmware mismatch this thread is terminated
in pci_probe.
bfa_fcs_lport.c, fabric.c, fcs_lport.h & vport.c:
* Split the lport init to attach time and init time code, so that
proper config attributes are set after firmware mismatch.
bfa_iocfc.c:
* Handle an IOC timer issue, where the IOC timer would expire before
the init completion and send Init fail event to the driver,
however IOC init continues and completes successfully at the later
stage. The bfa and driver were not handling this kind of deferred
init completion.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Brocade CNA currently supports only 190 vports (instead of 191),
since there are only 192 unicast cam entries reserved for FCoE.
Brocade CNA has a total of 256 unicast cam entries (192 FCoE + 64 LL)
192 cam entries = 1 burned in mac + 1 baseport FPMA mac + 190 vport
FPMA macs.
Made changes to the code to support only 190 vports.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Split bfa_fcs_init() into bfa_fcs_attach() and bfa_fcs_init().
Removed empty function definitions in FCS modules
Modified driver to call bfa_fcs_attach() and bfa_fcs_init() as needed.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added a FCS function to be called during driver init, to set the FDMI
Driver parameter.
fdmi.c: Created a disabled state when fdmi is disabled.
bfad.c:
* Added fdmi_enable driver parameter.
* Added support to call bfa_fcs_set_fdmi_param() to initialize fcs
fdmi setting.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
bfa_intr.c: Enable new halt interrupt in BFA.
bfi_ctreg.h: Expose new halt interrupt bit definition to host.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
bfa_ioc.c:
- Enable IOC auto-recovery by default.
- When CNA is in FC mode, return IOC type as FC (not FCoE)
bfa_iocfc.c:
- Set fcmode before pci initialization/setup.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Clear virtual links was not propagated upwards to bfa from fw.
This resulted in HBA and switch being in an inconsistent state.
So defined a new LPS event for clear virtual link on a vport,
and also now clear virtual link on a baseport, is sent as a
link down event from the fw.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added separate MSI-X module parameters to selectively
enable / disable MSI-X interrupts for both Brocade HBA and CNA's.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
RAID attributes uses scsi_is_sdev_device() to gate some SCSI specific
checking code. This causes two problems. Firstly if SCSI == n just
defining scsi_is_sdev_device() to return false might not be enough to
prevent gcc from emitting the code (and thus referring to undefined
symbols), so this needs surrounding with an ifdef. Secondly, using
scsi_is_sdev_device() when SCSI is either y or m gives a subtle
problem in the m case: raid_attrs must also be m to use the symbol.
Do the usual Kconfig jiggery-pokery to fix this.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Doing CHECK="smatch --two-passes gives:
drivers/scsi/osd/osd_initiator.c +1435 osd_finalize_request warning: assignment to 'ret' was never used
Which is an unchecked possible allocation failure, Fixed.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Commit e3deec09 incorrectly assumed that the B0 and B1 page lengths were
limited to 32 bytes. The B0 VPD page length is defined to be 64 bytes
when the device supports thin provisioning. B1 is always defined to be
64 bytes.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Added round robin FCF failover on initial or FCF rediscovery FLOGI failure.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Prevent Vport discovery after reg_new_vport completes when physical
logged in using FDISC.
- Remove fast FCF failover fabric name matching. Allow failover to FCFs
connected to different fabrics.
- Added fast FCF failover in response to FCF DEAD event on current
FCF record.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Clear LPFC_DRIVER_ABORTED on FCP command completion.
- Clear exchange busy flag when I/O is aborted and found on aborted list.
- Free sglq when XRI_ABORTED event is processed before release of IOCB.
- Only process iocb as aborted when LPFC_DRIVER_ABORTED is set.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add NULL checks to the pointers for the config_async mailbox
and dump_wakeup_params mailbox.
- Add code to check return value of lpfc_read_sparams everywhere
and handle failures appropriately.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This uses the scatter-gather chaining feature of Smart Array
controllers. 32 scatter-gather elements are embedded in the
"command list", and the last element in the list may be marked
as a "chain pointer", and point to an additional block of
scatter gather elements. The precise number of scatter gather
elements supported is dependent on the particular kind of
Smart Array, and is determined at runtime by querying the
hardware.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The intent of the scan thread was to allow a UNIT ATTENTION/LUN
DATA CHANGED condition encountered in the interrupt handler
to trigger a rescan of devices, which can't be done in interrupt
context. However, we weren't able to get this to work, due to
multiple such UNIT ATTENTION conditions arriving during the rescan,
during updating of the SCSI mid layer, etc. There's no way to tell
the devices, "stand still while I scan you!" Since it doesn't work,
there's no point in having the thread, as the rescan triggered via
ioctl or sysfs can be done without such a thread.
Signed-off-by: Mike Miller <mikem@beardog.cce.hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The SCSI status does not need to be shifted.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Adds support for resuming from suspend for IBM VFC devices. We may have
lost an interrupt over the suspend, so we just kick the interrupt handler
to process anything that is outstanding. We expect to find a transport event
indicating we need to reestablish our CRQ.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Adds support for resuming from suspend for IBM VSCSI devices. We may have
lost an interrupt over the suspend, so we just kick the interrupt handler
to process anything that is outstanding. We expect to find a transport event
indicating we need to reestablish our CRQ.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch ensures that we alloc only one EQ
if we are if we are not in msix mode
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch fixes some situations where enough resources were not
avaialable when targets exceeded a certain limit
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch removes some debug lines which are unnecessary and
also aligns some lines in code
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Robert Love