Getting the mvm station out of station id requires dereferencing
the station id to get ieee80211_sta, then checking for pointer
validity and only then extract mvm station out.
Given that there are helpers to do it - use them instead of
duplicating the code whenever we need only mvm station.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_phy_db_set_section() is get called only from atomic
context, the alloc_ctx parameter is not needed. Remove it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Driver is agnostic to the number of the phy_db entries and
only serves the firmware as a pipe to move the data from init
image to RT image.
As the size of the arrays may change (as it does in 9000 device)
allocate it dynamically. Firmware sends the largest index first
so we can use this to know how much we should allocate.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Our device supports only 160 GHz and not 80+80. Fix
VHT flag accordingly.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Up till now, the reorder buffer uses standard spec based comparison
when comparing the buffer status to NSSN. This indeed works for the
regular case, since we shouldn't cross the 2048 boundary without
getting a frame release notification.
However, this is problematic due to packet filtering that may be
performed by the FW while we are in d0i3. Theoretically we may
filter over 2048 packets, and then the check of the NSSN will get
incorrect.
Change the comparison to always trust nssn unless it is 64 or less
frames behind the head - which might happen due to a timeout.
This new comparison is to be used only when comparing reorder buffer
head with nssn, and not when comparing the packet SN to nssn or
reorder buffer head.
Put this in a separate commit as the logic is a bit tricky and
stands for its own commit message.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
CSR registers are always available even when the NIC is not awake, no
need to wake up the NIC before accessing them. This has a huge impact
when we re-enable an interrupt at the end of the ISR since waking up the
NIC can take some time.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Previous patch had changed firmware name convention for
new generation product. The firmware name is now longer
than the former convention. Adapt max firmware name length
to the new convention.
Fixes: e1ba684f76 ("iwlwifi: 8000: fix MODULE_FIRMWARE input")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently code allows mvm reference to become negative and
only warns in case mvm reference is released while reference
counting is 0.
However, we better prevent this from happening at all since
iwl_mvm_unref() may race against iwl_mvm_unref_all_except()
which is called on restart.
As a result we might get the same reference unreferenced twice
ending with a negative value:
An example for an easily reproduced log:
[ 2689.909166] iwl_mvm_ref Take mvm reference - type 8
[ 2690.732716] iwl_mvm_unref_all_except Cleanup: remove mvm ref type 8 (1)
[ 2690.849708] iwl_mvm_unref Leave mvm reference - type 8
[ 2690.849721] WARNING: ... iwl_mvm_unref+0xb0/0xc0 [iwlmvm]()
If there will be yet another another restart iwl_mvm_unref_all_except
will run from 0 up to ref count, and since it is unsigned, we will throw
the transport ref count completely out of balance:
iwl_mvm_unref_all_except[I] -- Cleanup: remove mvm ref type 8 (255)
iwl_trans_slv_unref[I] -- rpm counter: 0
iwl_trans_slv_unref[I] -- rpm counter: -1
iwl_trans_slv_unref[I] -- rpm counter: -2
...
iwl_trans_slv_unref[I] -- rpm counter: -253
iwl_trans_slv_unref[I] -- rpm counter: -254
As there is no valid scenario where we can get to a negative
reference count - prevent it from happening.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add UREG, RXFC, RFH, WMAL and RL2P registers to the prph dump
upon error. These regesiters could help to debug MSI-X and other
issues.
These register should be dumped only when multi-queue rx is supported
so separate the prph ranges static array to two different arrays,
and enable dumping different prph ranges according to run-time
decision.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a data packet is received, we need to make sure that we stay
awake until it can be processed and wait a while before trying to
enter runtime_suspend os system_suspend again. To do so, add a new
reference type for RX data and take the reference when sending the
packet to mac80211. We only do this for data packets, all the other
RX packets sent by the firmware (e.g. notifications) are not a reason
to prevent suspend.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we've already looked up the transmitter station, we can just
pass it to mac80211 using the new ieee80211_rx_napi(). This saves
the overhead of looking it up in mac80211 again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Devices belonging to 9000 family can support VHT 160MHz channel
width, so need to consider it when configuring VHT capabilities.
However, NVM file doesn't have a single bit specifying that 160MHz
is supported. This patch turns on 160MHz support in VHT capabilities
in case there's at least one channel supporting 160MHz.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently there is one to one function between device id to it's ucode.
The new generation devices allows to combine different phy and mac images.
Now we have two different ucode images with the same device id.
Read RF ID to identify phy image and overwrite it if needed.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If a host command was queued while in runtime suspend, it would go out
before the D0I3_END_CMD was sent. Sometimes it works, but sometimes
it fails, and it is obviously the wrong thing to do.
To fix this, have the opmode take a reference before sending a SYNC
command and make the pcie trans wait for the runtime state to become
active before actually queueing the command.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is a debugfs knob to configure the maximal length
of the A-MSDU. If this value is not 0 (which is the
default), allow Tx A-MSDU even if the rate control
disallows it.
While at it, add "unlikely" to the if that limits the
length of the A-MSDU based on the debugfs hook.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Rename 9560 to 9260.
Add new PCI ID for 9260 and change some entries from 5165 to 9260.
Also order the 9000 series.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a constant to allow disabling checksum. This will enable easier
debugging in early phases.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order for mac80211 to use per-CPU statistics for RSS RX, the
driver needs to advertise that it uses RSS. Do this when using
more than a single queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It's cleaner to always call the iwl_trans_ref/unref() functions
instead of sometimes calling the trans-specific ops directly. This
also prepares for moving some of the code from the trans-specific ops
to the common trans code.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
To indicate to the FW that a queue has been removed, an
existing flag in the ADD_STA HCMD (that hasn't been in use)
has been changed to indicate that a queue is being removed
from a STA.
Update this in the driver code.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware will send frame release notification in order
to release "stuck" frames on a queue where no more frames
arrive on.
Upon receiving the message the driver shall indicate the frames
up to the NSSN.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a timer in order to release expired frames from the
reorder buffer.
This is needed since some APs do not retransmit frames
to fill in the reorder holes and in TCP it results with
a complete stall of traffic.
This has a few side effects on the general design:
The nssn may not reflect the the head of the reorder buffer.
This situation is valid, and packets with SN lower than the
reorder buffer head will be dropped.
Another side effect is that since the reorder timer might expire
we need to lock the reorder buffer.
This however is fine since the locking is only inside a
single reorder buffer between RX path and reorder timeout and
there is no outside contention.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Next hardware will direct packets to core based on the TCP/UDP
streams.
This logic can create holes in reorder buffer since packets that
belong to other stream were directed to a different core.
However, those are valid holes and the packets can be indicated
in L3 order.
The hardware will utilize a mechanism of informing the driver of
the normalized ssn and the driver shall release all packets that
SN is lower than the nssn.
This enables managing the reorder across the queues without sharing
any data between them.
The reorder buffer is allocated and released directly in the RX path
in order to avoid various races between control path and rx path.
The code utilizes the internal messaging to notify rx queues of when
to delete the reorder buffer.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add the firmware API name to the struct iwl_wowlan_gtk_status.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
According to the spec when a BA session is started there
is a timeout set for the session in the ADDBA request.
If there is not activity on the TA/TID then the session
expires and a DELBA is sent.
In order to check for the timeout, data must be shared
among the rx queues.
Add a timer that runs as long as BA session is active
for the station and stops aggregation session if needed.
This patch also lays the infrastructure for the reordering
buffer which will be enabled in the next patches.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently the sync notification is a type of notification. However, it
is better fitted as an attribute of a notification, since there might
be another message in the payload (delba for instance) that should be
sent while control path is waiting for all queues to process.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
mac80211 will call the driver whenever there is a race between
RSS queues and control path that requires a processing of all
pending frames in RSS queues.
Implement that by utilizing the internal notification mechanism:
queue a message to all queues. When the message is received on
a queue it decrements the atomic counter. This guarantees that
all pending frames in the RX queue were processed since the message
is in order inside the queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sometimes current polling count is not sufficient.
This patch increases it to 100.
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Support sending P2P device frames should be sent from
queue #2, as required in DQA mode.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
all drivers - removing the duplicated enum ieee80211_band and
replacing it by enum nl80211_band. On top of that, just a small
documentation update.
-----BEGIN PGP SIGNATURE-----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=2xfe
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-04-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next into master
To synchronize with Kalle, here's just a big change that affects
all drivers - removing the duplicated enum ieee80211_band and
replacing it by enum nl80211_band. On top of that, just a small
documentation update.
Since commit cd6cfd7311
"ath9k: do not set half/quarter channel flags in AR_PHY_MODE" the
condition "rfMode & (AR_PHY_MODE_QUARTER | AR_PHY_MODE_HALF)" would
never evaluate to true.
Fix this by using the available IS_CHAN_HALF_RATE and IS_CHAN_QUARTER_RATE
marcros instead.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's no need to keep the same for loop twice in the code.
Move the txpower cap before the loop to reduce code complexity.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since ATH9K_TX99 depends on ATH9K_DEBUGFS anyway move it there
such that "make menuconfig" will indent TX99 support below ath9k
debugging.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The same functionality as ar9003_hw_tx_power_regwrite is hardcoded in
ar9003_hw_tx99_set_txpower. Just reuse the existing ar9003_hw_tx_power_regwrite
for TX99 setup too.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During hw scan, firmware sends two channel information events (pre-
complete, complete) to host for each channel change. The snap shot of cycle
counters (rx_clear and total) between these two events are given for
survey dump. In order to get latest survey statistics of all channels, a
scan request has to be issued. In general, an AP DUT is brought up, it
won't leave BSS channel except few cases like overlapping bss or radar
detection. So survey statistics of bss channel is always referring to
older data that are collected before starting AP (either ACS/OBSS scan).
To collect latest survey information from target, firmware provides WMI
interface to read cycle counters from hardware. For each survey dump
request, BSS channel cycle counters are read and cleared in hardware.
This makes sure that behavior is in align with ath9k survey report.
So survey dump always gives snap shot of cycle counters b/w two survey
requests.
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add handler to process bss channel information wmi event that
will be received upon sending pdev_chan_info_request wmi command.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI ops to send pdev_bss_chan_info_request command to target.
This command will be used to retrieve updated cycle counters and noise
floor value of current operating channel (bss channel).
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI definitions for pdev bss channel information request and
event.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is observed that while loading and unloading ath10k modules
in an infinite loop, before ath10k_core_start() completion HTT
rx frames are received, while processing these frames,
dereferencing the arvifs list code is getting hit before
initilizing the arvifs list, causing a kernel panic.
This patch initilizes the arvifs list before initilizing htt.
Fixes the below issue:
[<bf88b058>] (ath10k_htt_rx_pktlog_completion_handler+0x278/0xd08 [ath10k_core])
[<bf88b058>] (ath10k_htt_rx_pktlog_completion_handler [ath10k_core])
[<bf88c0dc>] (ath10k_htt_txrx_compl_task+0x5f4/0xeb0 [ath10k_core])
[<bf88c0dc>] (ath10k_htt_txrx_compl_task [ath10k_core])
[<c0234100>] (tasklet_action+0x8c/0xec)
[<c0234100>] (tasklet_action)
[<c02337c0>] (__do_softirq+0xf8/0x228)
[<c02337c0>] (__do_softirq) [<c0233920>] (run_ksoftirqd+0x30/0x90)
Code: e5954ad8 e2899008 e1540009 0a00000d (e5943008)
---[ end trace 71de5c2e011dbf56 ]---
Kernel panic - not syncing: Fatal exception in interrupt
Fixes: 500ff9f938 ("ath10k: implement chanctx API")
Cc: <stable@vger.kernel.org>
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Spectral related structures are accessed / modified only if ath10k
debugfs is enabled, so it makes more sense to move them under
ATH10K_DEBUGFS
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
According to the spec, VHT doesn't exist in 2.4GHz.
There are vendor extensions to allow a subset of VHT to work
(notably 256-QAM), but since mac80211 doesn't support those
advertising VHT capability on 2.4GHz leads to the behaviour
of reporting VHT capabilities but not being able to use any
of them due to mac80211's code requiring 80 MHz support.
Remove the VHT capabilities from 2.4GHz for now. If mac80211
gets extended to use the (likely Broadcom) vendor IEs for it
and handles the lack of 80 MHz support, it can be added back.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The TSO code creates A-MSDUs from a single large send. Each
A-MSDU is an skb and skb->len doesn't include the number of
bytes which need to be added for the headers being added
(subframe header, TCP header, IP header, SNAP, padding).
To be able to set the right value in the Tx command, we
put the number of bytes added by those headers in
driver_data in iwl_mvm_tx_tso and use this value in
iwl_mvm_set_tx_cmd.
The problem by setting this value in driver_data is that
it overrides the ieee80211_tx_info. The bug manifested
itself when we send P2P related frames in CCK since the
rate in ieee80211_tx_info is zero-ed. This of course is
a violation of the P2P specification.
To fix this, copy the original ieee80211_tx_info to the
stack and pass it to the functions which need it.
Assign the number of bytes added by the headers to the
driver_data inside the skb itself.
Fixes: a6d5e32f24 ("iwlwifi: mvm: send large SKBs to the transport")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
With two different h2c_cmd() functions, mbox_ext_reg and
mbox_ext_width are no longer needed.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rename it to rtl8xxxu_gen2_prepare_calibrate() and remove the calls to
it from rtl8xxxu_gen1_phy_iq_calibrate()
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The H2C API is completely different between gen1 and gen2 parts, so
there is little point trying to treat this as a generic function. All
calls to *_h2c_cmd() will always come from a gen1 or a gen2 specific
function.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function is generic to most of the chips, so change the name to
reflect this.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sara Sharon