Added a flag to indicate a panic_write so that low level drivers can
use it to take required action where applicable, to ensure oops data
gets written to assigned mtd device.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The NAND core has a NAND operation tracing function, but it can only
be used by drivers using the generic option parser from the NAND core.
Export the tracing function as a static inline function in rawnand.h
so that drivers implementing exec_op directly do not have to write their
own operation tracing.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Used in several S5PV210-based Galaxy S devices, among them SGH-T959V,
SGH-T959P, SGH-T839, and SPH-D700.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cypress' HyperBus is Low Signal Count, High Performance Double Data Rate
Bus interface between a host system master and one or more slave
interfaces. HyperBus is used to connect microprocessor, microcontroller,
or ASIC devices with random access NOR flash memory (called HyperFlash)
or self refresh DRAM (called HyperRAM).
Its a 8-bit data bus (DQ[7:0]) with Read-Write Data Strobe (RWDS)
signal and either Single-ended clock(3.0V parts) or Differential clock
(1.8V parts). It uses ChipSelect lines to select b/w multiple slaves.
At bus level, it follows a separate protocol described in HyperBus
specification[1].
HyperFlash follows CFI AMD/Fujitsu Extended Command Set (0x0002) similar
to that of existing parallel NORs. Since HyperBus is x8 DDR bus,
its equivalent to x16 parallel NOR flash with respect to bits per clock
cycle. But HyperBus operates at >166MHz frequencies.
HyperRAM provides direct random read/write access to flash memory
array.
But, HyperBus memory controllers seem to abstract implementation details
and expose a simple MMIO interface to access connected flash.
Add support for registering HyperFlash devices with MTD framework. MTD
maps framework along with CFI chip support framework are used to support
communicating with flash.
Framework is modelled along the lines of spi-nor framework. HyperBus
memory controller (HBMC) drivers calls hyperbus_register_device() to
register a single HyperFlash device. HyperFlash core parses MMIO access
information from DT, sets up the map_info struct, probes CFI flash and
registers it with MTD framework.
Some HBMC masters need calibration/training sequence[3] to be carried
out, in order for DLL inside the controller to lock, by reading a known
string/pattern. This is done by repeatedly reading CFI Query
Identification String. Calibration needs to be done before trying to detect
flash as part of CFI flash probe.
HyperRAM is not supported at the moment.
HyperBus specification can be found at[1]
HyperFlash datasheet can be found at[2]
[1] https://www.cypress.com/file/213356/download
[2] https://www.cypress.com/file/213346/download
[3] http://www.ti.com/lit/ug/spruid7b/spruid7b.pdf
Table 12-5741. HyperFlash Access Sequence
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
HyperFlash devices are compliant with CFI AMD/Fujitsu Extended Command
Set (0x0002) for flash operations, therefore
drivers/mtd/chips/cfi_cmdset_0002.c can be used as is. But these devices
do not support DQ polling method of determining chip ready/good status.
These flashes provide Status Register whose bits can be polled to know
status of flash operation.
Cypress HyperFlash datasheet here[1], talks about CFI Amd/Fujitsu
Extended Query version 1.5. Bit 0 of "Software Features supported" field
of CFI Primary Vendor-Specific Extended Query table indicates
presence/absence of status register and Bit 1 indicates whether or not
DQ polling is supported. Using these bits, its possible to determine
whether flash supports DQ polling or need to use Status Register.
Add support for polling Status Register to know device ready/status of
erase/write operations when DQ polling is not supported.
Print error messages on erase/program failure by looking at related
Status Register bits.
[1] https://www.cypress.com/file/213346/download
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tokunori Ikegami <ikegami.t@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
- Fix a bug uncovered by a recent patch on Spansion SPI-NOR flashes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl0Pwk0ACgkQJWrqGEe9
VoS8nwf7B76jN39/g32Hfp4JT/B7cntrHzTGxfUT9NAhKa4MaI7FOU2eeTryaVdO
32OJlttV+r0Fu6p+In1VXCk4j1YlkcOaxqB1VXsMEaQ+Vt8ONVTbJX/cqyGC/ogq
MZlO8Rys4MGmq7vRiZ+1SD8lOV4qXgmX3D38NjUQ1oCAMCCgJgkWYFV2tv9Eie09
2CCT3IBFj+D34qaBiM+qocGtnzWfB9477A6ZeI4BwjUe1ZtoEYeIOrCXWiywabjM
msHRN1tNt5kfINnx0TkQFcnpbdDo5tMyTHCkEQt5Ewdae4vyCv7xTHTCZEttC7Ic
Rx2yONzrZGQVP4c27y22K954C1jGcg==
=ZiPm
-----END PGP SIGNATURE-----
Merge tag 'mtd/fixes-for-5.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd fixes from Miquel Raynal:
- Set the raw NAND number of targets to the right value
- Fix a bug uncovered by a recent patch on Spansion SPI-NOR flashes
* tag 'mtd/fixes-for-5.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: spi-nor: use 16-bit WRR command when QE is set on spansion flashes
mtd: rawnand: initialize ntargets with maxchips
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 24 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170026.162703968@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
51 franklin st fifth floor boston ma 02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 50 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190523091649.499889647@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To be able to check and set bad block markers in the first and
second page of a block independently of each other, we create
separate flags for both cases.
Previously NAND_BBM_SECONDPAGE meant, that both, the first and the
second page were used. With this patch NAND_BBM_FIRSTPAGE stands for
using the first page and NAND_BBM_SECONDPAGE for using the second
page.
This patch is only for preparation of subsequent changes and does
not implement the logic to actually handle both flags separately.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that we have moved the information to the chip level, let's
remove all the unused flags and fields.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The information about where the manufacturer puts the bad block
markers inside the bad block and in the OOB data is stored in
different places. Let's move this information to the chip struct,
as we did it for rawnand.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The information about where the manufacturer puts the bad block
markers inside the bad block and in the OOB data is stored in
different places. Let's move this information to nand_chip.options
and nand_chip.badblockpos.
As this chip-specific information is not directly related to the
bad block table (BBT), we also rename the flags to NAND_BBM_*.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently, drivers are able to constify a nand_op_parser array,
but not nand_op_parser_pattern and nand_op_parser_pattern_elem
since they are instantiated by using the NAND_OP_PARSER(_PATTERN).
Add 'const' to them in order to move more driver data from .data to
.rodata section.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Sphinx doesn't handle expressions in identifier references.
This fixes the following warnings:
./include/linux/mtd/rawnand.h:1184: WARNING: Inline strong start-string without end-string.
./include/linux/mtd/rawnand.h:1186: WARNING: Inline strong start-string without end-string.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is no point in having two distinct entries, merge them and
rename the symbol for more clarity: MTD_NAND_ECC_SW_BCH
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_device embeds a nand_ecc_req object which contains the minimum
strength and step-size required by the NAND device.
Drop the chip->ecc_{strength,step}_ds fields and use
chip->base.eccreq.{strength,step_size} instead.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The same information is provided by nanddev_ntargets().
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The target size can now be returned by nanddev_get_targetsize(). Get
rid of the chip->chipsize field and use this helper instead.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that we inherit from nand_device, we can use
nand_device->memorg.bits_per_cell instead of having our own field at
the nand_chip level.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
nanddev_mtd_max_bad_blocks() is implemented by the generic NAND layer
and is already doing what we need. Reuse this function instead of
having our own implementation.
While at it, get rid of the ->max_bb_per_die and ->blocks_per_die
fields which are now unused.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Looking at the field names it's hard to tell what ->data_buf, ->pagebuf
and ->pagebuf_bitflips are for. Clarify that by moving those fields
in a sub-struct named pagecache.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
We plan to move cache related fields to a pagecache struct in nand_chip
but some drivers access ->pagebuf directly to invalidate the cache
before they start using ->data_buf.
Let's provide an helper that returns a pointer to ->data_buf after
invalidating the cache.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The generic NAND layer provides abstraction of NAND devices no matter
the bus that is used to communicate with the chip. Basing the raw NAND
core on this generic layer should avoid duplication of common
operations, like iterating over all pages/blocks for MTD IO/erase
operations.
In order to re-use this layer, we must first inherit from nand_device
and then initialize the nand_device struct appropriately. This patch
is taking care of the former.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Use the nand_to_mtd() helper to access chip->mtd as done everywhere
else.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Will be used by the raw NAND framework.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Some drivers in the raw NAND framework seems to need this helper, so
let's just add it instead of open-coding the logic.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
NAND datasheets usually give the maximum number of bad blocks per LUN
and this number can be used to help upper layers decide how much blocks
they should reserve for bad block handling.
Add a max_bad_eraseblocks_per_lun to the nand_memory_organization
struct and update the NAND_MEMORG() macro (and its users) accordingly.
We also provide a default mtd->_max_bad_blocks() implementation.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Make use of the spi-mem direct mapping API to let advanced controllers
optimize read/write operations when they support direct mapping.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Stefan Roese <sr@denx.de>
- Fourth batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (Sunxi, Marvell, MTK, TMIO, OMAP2).
- Checking the return code of nand_reset() and nand_readid_op().
- Removing ->legacy.erase and single_erase().
- Simplifying the locking.
- Several implicit fall through annotations.
Raw NAND controllers drivers changes:
- Fixing various possible object reference leaks (MTK, JZ4780, Atmel).
- ST:
* Adding support for STM32 FMC2 NAND flash controller.
- Meson:
* Adding support for Amlogic NAND flash controller.
- Denali:
* Several cleanup patches.
- Sunxi:
* Several cleanup patches.
- FSMC:
* Disabling NAND on remove().
* Resetting NAND timings on resume().
SPI-NAND drivers changes:
- Toshiba:
* Adding support for all Toshiba products.
- Macronix:
* Fixing ECC status read.
- Gigadevice:
* Adding support for GD5F1GQ4UExxG.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAlxwE4kACgkQJWrqGEe9
VoRQVQf+OOkScM6ZbsO2GbMRe0ybMOCOyBXfojPEGtVv80gHHrAPRocLqWMB1Xdb
MSfm7j+lyZU1I8eYVvdYXby7s5FlVWbrh8NSnnwox1QusdmyBm7vcxc6st15Poy/
/WtjE+Cry49eIx5L/pmmNH3AIqMdvSRTJD7NgOYjo/SIq4GLR+KQEgt1VLp/KyO0
TGeMDIT3Q3+MXVwvUh3YlHUwNJ2jOpjpPW94QxD0mef/b9doUlkvrOdHs3JeGQzX
aiiqWI1nRBmjNs34wp7Dyf3G/feplKyi+IS/ghTiijAgwbWdRI7KxrPtyCUYiint
3XqVgZAF/sfFaKFMIiJBMzoLQB15dQ==
=VbaE
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.1' of git://git.infradead.org/linux-mtd into mtd/next
NAND core changes:
- Fourth batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (Sunxi, Marvell, MTK, TMIO, OMAP2).
- Checking the return code of nand_reset() and nand_readid_op().
- Removing ->legacy.erase and single_erase().
- Simplifying the locking.
- Several implicit fall through annotations.
Raw NAND controllers drivers changes:
- Fixing various possible object reference leaks (MTK, JZ4780, Atmel).
- ST:
* Adding support for STM32 FMC2 NAND flash controller.
- Meson:
* Adding support for Amlogic NAND flash controller.
- Denali:
* Several cleanup patches.
- Sunxi:
* Several cleanup patches.
- FSMC:
* Disabling NAND on remove().
* Resetting NAND timings on resume().
SPI-NAND drivers changes:
- Toshiba:
* Adding support for all Toshiba products.
- Macronix:
* Fixing ECC status read.
- Gigadevice:
* Adding support for GD5F1GQ4UExxG.
Now that the last user of this hook, denali.c, stopped using it,
we can remove the erase hook from nand_legacy.
I squashed single_erase() because only the difference between
single_erase() and nand_erase_op() is the number of bit shifts.
The status/ret conversion in nand_erase_nand() is unneeded since
commit eb94555e9e ("mtd: nand: use usual return values for the
->erase() hook"). Cleaned it up now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_get_device() was complex for apparently no good reason. Let's
replace this locking scheme with 2 mutexes: one attached to the
controller and another one attached to the chip.
Every time the core calls nand_get_device(), it will first lock the
chip and if the chip is not suspended, will then lock the controller.
nand_release_device() will release both lock in the reverse order.
nand_get_device() can sleep, just like the previous implementation,
which means you should never call that from an atomic context.
We also get rid of
- the chip->state field, since all it was used for was flagging the
chip as suspended. We replace it by a field called chip->suspended
and directly set it from nand_suspend/resume()
- the controller->wq and controller->active fields which are no longer
needed since the new controller->lock (now a mutex) guarantees that
all operations are serialized at the controller level
- panic_nand_get_device() which would anyway be a no-op. Talking about
panic write, I keep thinking the rawnand implementation is unsafe
because there's not negotiation with the controller to know when it's
actually done with it's previous operation. I don't intend to fix
that here, but that's probably something we should look at, or maybe
we should consider dropping the ->_panic_write() implementation
Last important change to mention: we now return -EBUSY when someone
tries to access a device that as been suspended, and propagate this
error to the upper layer.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
- Add opcodes for octal I/O commands
* Read : 1-1-8 and 1-8-8 protocol
* Write : 1-1-8 and 1-8-8 protocol
* opcodes for 4-byte address mode command
- Entry of macros in _convert_3to4_xxx function
- Add flag SPI_NOR_OCTAL_READ specifying flash support octal read
commands. This flag is required for flashes which didn't provides
support for auto detection of Octal mode capabilities i.e. not
seems to support newer JESD216C standard.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Here is the big set of char and misc driver patches for 4.21-rc1.
Lots of different types of driver things in here, as this tree seems to
be the "collection of various driver subsystems not big enough to have
their own git tree" lately.
Anyway, some highlights of the changes in here:
- binderfs: is it a rule that all driver subsystems will eventually
grow to have their own filesystem? Binder now has one to handle the
use of it in containerized systems. This was discussed at the
Plumbers conference a few months ago and knocked into mergable shape
very fast by Christian Brauner. Who also has signed up to be
another binder maintainer, showing a distinct lack of good judgement :)
- binder updates and fixes
- mei driver updates
- fpga driver updates and additions
- thunderbolt driver updates
- soundwire driver updates
- extcon driver updates
- nvmem driver updates
- hyper-v driver updates
- coresight driver updates
- pvpanic driver additions and reworking for more device support
- lp driver updates. Yes really, it's _finally_ moved to the proper
parallal port driver model, something I never thought I would see
happen. Good stuff.
- other tiny driver updates and fixes.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXCZCUA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymF9QCgx/Z8Fj1qzGVGrIE4flXOi7pxOrgAoMqJEWtU
ywwL8M9suKDz7cZT9fWQ
=xxr6
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char and misc driver patches for 4.21-rc1.
Lots of different types of driver things in here, as this tree seems
to be the "collection of various driver subsystems not big enough to
have their own git tree" lately.
Anyway, some highlights of the changes in here:
- binderfs: is it a rule that all driver subsystems will eventually
grow to have their own filesystem? Binder now has one to handle the
use of it in containerized systems.
This was discussed at the Plumbers conference a few months ago and
knocked into mergable shape very fast by Christian Brauner. Who
also has signed up to be another binder maintainer, showing a
distinct lack of good judgement :)
- binder updates and fixes
- mei driver updates
- fpga driver updates and additions
- thunderbolt driver updates
- soundwire driver updates
- extcon driver updates
- nvmem driver updates
- hyper-v driver updates
- coresight driver updates
- pvpanic driver additions and reworking for more device support
- lp driver updates. Yes really, it's _finally_ moved to the proper
parallal port driver model, something I never thought I would see
happen. Good stuff.
- other tiny driver updates and fixes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (116 commits)
MAINTAINERS: add another Android binder maintainer
intel_th: msu: Fix an off-by-one in attribute store
stm class: Add a reference to the SyS-T document
stm class: Fix a module refcount leak in policy creation error path
char: lp: use new parport device model
char: lp: properly count the lp devices
char: lp: use first unused lp number while registering
char: lp: detach the device when parallel port is removed
char: lp: introduce list to save port number
bus: qcom: remove duplicated include from qcom-ebi2.c
VMCI: Use memdup_user() rather than duplicating its implementation
char/rtc: Use of_node_name_eq for node name comparisons
misc: mic: fix a DMA pool free failure
ptp: fix an IS_ERR() vs NULL check
genwqe: Fix size check
binder: implement binderfs
binder: fix use-after-free due to ksys_close() during fdget()
bus: fsl-mc: remove duplicated include files
bus: fsl-mc: explicitly define the fsl_mc_command endianness
misc: ti-st: make array read_ver_cmd static, shrinks object size
...
- Parse the 4BAIT SFDP section
- Add a bunch of SPI NOR entries to the flash_info table
- Add the concept of SFDP fixups and use it to fix a bug on MX25L25635F
- A bunch of minor cleanups/comestic changes
-----BEGIN PGP SIGNATURE-----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=JXhP
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-4.21' of git://git.infradead.org/linux-mtd into mtd/next
Core changes:
- Parse the 4BAIT SFDP section
- Add a bunch of SPI NOR entries to the flash_info table
- Add the concept of SFDP fixups and use it to fix a bug on MX25L25635F
- A bunch of minor cleanups/comestic changes
NAND core changes:
- kernel-doc miscellaneous fixes.
- Third batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (ams-delta, marvell, fsmc, denali, tegra, vf610):
* Stopping to pass mtd_info objects to internal functions
* Reorganizing code to avoid forward declarations
* Dropping useless test in nand_legacy_set_defaults()
* Moving nand_exec_op() to internal.h
* Adding nand_[de]select_target() helpers
* Passing the CS line to be selected in struct nand_operation
* Making ->select_chip() optional when ->exec_op() is implemented
* Deprecating the ->select_chip() hook
* Moving the ->exec_op() method to nand_controller_ops
* Moving ->setup_data_interface() to nand_controller_ops
* Deprecating the dummy_controller field
* Fixing JEDEC detection
* Providing a helper for polling GPIO R/B pin
Raw NAND chip drivers changes:
- Macronix:
* Flagging 1.8V AC chips with a broken GET_FEATURES(TIMINGS)
Raw NAND controllers drivers changes:
- Ams-delta:
* Fixing the error path
* SPDX tag added
* May be compiled with COMPILE_TEST=y
* Conversion to ->exec_op() interface
* Dropping .IOADDR_R/W use
* Use GPIO API for data I/O
- Denali:
* Removing denali_reset_banks()
* Removing ->dev_ready() hook
* Including <linux/bits.h> instead of <linux/bitops.h>
* Changes to comply with the above fixes/cleanup done in the core.
- FSMC:
* Adding an SPDX tag to replace the license text
* Making conversion from chip to fsmc consistent
* Fixing unchecked return value in fsmc_read_page_hwecc
* Changes to comply with the above fixes/cleanup done in the core.
- Marvell:
* Preventing timeouts on a loaded machine (fix)
* Changes to comply with the above fixes/cleanup done in the core.
- OMAP2:
* Pass the parent of pdev to dma_request_chan() (fix)
- R852:
* Use generic DMA API
- sh_flctl:
* Converting to SPDX identifiers
- Sunxi:
* Write pageprog related opcodes to the right register: WCMD_SET (fix)
- Tegra:
* Stop implementing ->select_chip()
- VF610:
* Adding an SPDX tag to replace the license text
* Changes to comply with the above fixes/cleanup done in the core.
- Various trivial/spelling/coding style fixes.
SPI-NAND drivers changes:
- Removing the depreacated mt29f_spinand driver from staging.
- Adding support for:
* Toshiba TC58CVG2S0H
* GigaDevice GD5FxGQ4xA
* Winbond W25N01GV
Add support for SFDP (JESD216B) 4-byte Address Instruction Table. This
table is optional but when available, we parse it to get the 4-byte
address op codes supported by the memory.
Using these op codes is stateless as opposed to entering the 4-byte
address mode or setting the Base Address Register (BAR).
Flashes that have the 4BAIT table declared can now support
SPINOR_OP_PP_1_1_4_4B and SPINOR_OP_PP_1_4_4_4B opcodes.
Tested on MX25L25673G.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@microchip.com>
[tudor.ambarus@microchip.com:
- rework erase and page program logic,
- pass DMA-able buffer to spi_nor_read_sfdp(),
- introduce SPI_NOR_HAS_4BAIT
- various minor updates.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Add SPDX tags to replace the license boiler-plate and fix the
MODULE_LICENSE() definition in spi-nor.c to match the license text
(GPL v2).
Interestingly, spi-nor.h and spi-nor.c do not use the same license
(GPL v2+ for spi-nor.h, GPL v2 for spi-nor.c).
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Some flash_info entries have the SPI_NOR_4B_OPCODES flag set to let the
core know that the flash supports 4B opcode. While this solution works
fine for id-based caps detection, it doesn't work that well when relying
on SFDP-based caps detection. Let's add an SNOR_F_4B_OPCODES flag so
that the SFDP parsing code can set it when appropriate.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Some MICRON related macros in spi-nor domain were ST.
Rename entries related to STMicroelectronics under macro SNOR_MFR_ST.
Added entry of MFR Id for Micron flashes, 0x002C.
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
We try to force NAND controller drivers to properly separate the NAND
controller object from the NAND chip one, so let's deprecate the dummy
controller object embedded in nand_chip to encourage them to create
their own instance.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
->setup_data_interface() is a controller specific method and should
thus be placed in nand_controller_ops.
In order to make that work with controllers that support keeping
pre-configured timings we need to add a new NAND_KEEP_TIMINGS flag to
inform the core it should skip the timings selection step.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
->exec_op() is a controller method and has nothing to do in the
nand_chip struct. Let's move it to the nand_controller_ops struct and
adjust the core and drivers accordingly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS line to be selected is passed to ->exec_op() and
stored in chip->cur_cs and after patching all drivers implementing
->exec_op() to stop implementing this method, we can deprecate it by
moving it to the nand_legacy structure.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In order to deprecate the ->select_chip hook we need to pass the CS
line a NAND operations are targeting. This is done through the
addition of a cs field to the nand_operation struct.
We also need to keep track of the currently selected target to
properly initialize op->cs, hence the ->cur_cs field addition to the
nand_chip struct.
Note that op->cs is not assigned in nand_exec_op() because we might
rework the way we execute NAND operations in the future (adopt a
queuing mechanism instead of the serialization we have right now).
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add a wrapper to prevent drivers and core code from directly calling
the ->select_chip hook which we are about to deprecate.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Looks like NAND_CONTROLLER_ALLOC has been introduced a long time ago
back when the dummy nand_hw_ctrl object was dynamically allocated
instead of being embedded in nand_chip.
We can safely get rid of this unused flag.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_exec_op() is only used by core code (nand_xxx.c files). Let's
move this inline function in drivers/mtd/nand/raw/internals.h.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Allow drivers that use the nvmem API to read data stored on MTD devices.
For this the mtd devices are registered as read-only NVMEM providers.
We don't support device tree systems for now.
Signed-off-by: Alban Bedel <albeu@free.fr>
[Bartosz:
- include linux/nvmem-provider.h
- set the name of the nvmem provider
- set no_of_node to true in nvmem_config
- don't check the return value of nvmem_unregister() - it cannot fail
- tweaked the commit message]
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When allocating a new partition mtd subsystem runs internal tests in the
allocate_partition(). They may result in modifying specified flags (e.g.
dropping some /features/ like write access).
Those constraints don't have to be necessary true for subpartitions. It
may happen parent partition isn't block aligned (effectively disabling
write access) while subpartition may fit blocks nicely. In such case all
checks should be run again (starting with original flags value).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
mtd_oobavail() returns either mtd->oovabail or mtd->oobsize. Both
values are unsigned 32-bit entities, so there is no reason to pretend
returning a signed one.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
As original license mentioned, it is GPL-2.0 in SPDX.
Then, MODULE_LICENSE() should be "GPL v2" instead of "GPL".
See ${LINUX}/include/linux/module.h
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Function name is wrong in the kernel-doc header.
Fixes: 9c3736a3de ("mtd: nand: Add core infrastructure to deal with NAND devices")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Each controller driver having access to NAND R/B pin over GPIO would
have to reimplement the polling loop otherwise.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nanddev_neraseblocks() currently returns the number pages per LUN
instead of the total number of eraseblocks.
Fixes: 9c3736a3de ("mtd: nand: Add core infrastructure to deal with NAND devices")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Core changes:
* Support non-uniform erase size
* Support controllers with limited TX fifo size
Driver changes:
* m25p80: Re-issue a WREN command after each write access
* cadence: Pass a proper dir value to dma_[un]map_single()
* fsl-qspi: Check fsl_qspi_get_seqid() return val make sure 4B
addressing opcodes are properly handled
* intel-spi: Add a new PCI entry for Ice Lake
NAND changes:
Raw NAND core changes:
- Two batchs of cleanups of the NAND API, including:
* Deprecating a lot of interfaces (now replaced by ->exec_op()).
* Moving code in separate drivers (JEDEC, ONFI), in private files
(internals), in platform drivers, etc.
* Functions/structures reordering.
* Exclusive use of the nand_chip structure instead of the MTD one
all across the subsystem.
- Addition of the nand_wait_readrdy/rdy_op() helpers.
Raw NAND controllers drivers changes:
- Various coccinelle patches.
- Marvell:
* Use regmap_update_bits() for syscon access.
* More documentation.
* BCH failure path rework.
* More layouts to be supported.
* IRQ handler complete() condition fixed.
- Fsl_ifc:
* SRAM initialization fixed for newer controller versions.
- Denali:
* Fix licenses mismatch and use a SPDX tag.
* Set SPARE_AREA_SKIP_BYTES register to 8 if unset.
- Qualcomm:
* Do not include dma-direct.h.
- Docg4:
* Removed.
- Ams-delta:
* Use of a GPIO lookup table
* Internal machinery changes.
Raw NAND chip drivers changes:
- Toshiba:
* Add support for Toshiba memory BENAND
* Pass a single nand_chip object to the status helper.
- ESMT:
* New driver to retrieve the ECC requirements from the 5th ID byte.
MTD changes:
* physmap cleanups/fixe
* gpio-addr-flash cleanups/fixes
-----BEGIN PGP SIGNATURE-----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=7w4w
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.20' of git://git.infradead.org/linux-mtd
Pull mtd updates from Boris Brezillon:
"SPI NOR core changes:
- Support non-uniform erase size
- Support controllers with limited TX fifo size
Driver changes:
- m25p80: Re-issue a WREN command after each write access
- cadence: Pass a proper dir value to dma_[un]map_single()
- fsl-qspi: Check fsl_qspi_get_seqid() return val make sure 4B
addressing opcodes are properly handled
- intel-spi: Add a new PCI entry for Ice Lake
Raw NAND core changes:
- Two batchs of cleanups of the NAND API, including:
* Deprecating a lot of interfaces (now replaced by ->exec_op()).
* Moving code in separate drivers (JEDEC, ONFI), in private files
(internals), in platform drivers, etc.
* Functions/structures reordering.
* Exclusive use of the nand_chip structure instead of the MTD one
all across the subsystem.
- Addition of the nand_wait_readrdy/rdy_op() helpers.
Raw NAND controllers drivers changes:
- Various coccinelle patches.
- Marvell:
* Use regmap_update_bits() for syscon access.
* More documentation.
* BCH failure path rework.
* More layouts to be supported.
* IRQ handler complete() condition fixed.
- Fsl_ifc:
* SRAM initialization fixed for newer controller versions.
- Denali:
* Fix licenses mismatch and use a SPDX tag.
* Set SPARE_AREA_SKIP_BYTES register to 8 if unset.
- Qualcomm:
* Do not include dma-direct.h.
- Docg4:
* Removed.
- Ams-delta:
* Use of a GPIO lookup table
* Internal machinery changes.
Raw NAND chip drivers changes:
- Toshiba:
* Add support for Toshiba memory BENAND
* Pass a single nand_chip object to the status helper.
- ESMT:
* New driver to retrieve the ECC requirements from the 5th ID
byte.
MTD changes:
- physmap cleanups/fixe
- gpio-addr-flash cleanups/fixes"
* tag 'mtd/for-4.20' of git://git.infradead.org/linux-mtd: (93 commits)
jffs2: free jffs2_sb_info through jffs2_kill_sb()
mtd: spi-nor: fsl-quadspi: fix read error for flash size larger than 16MB
mtd: spi-nor: intel-spi: Add support for Intel Ice Lake SPI serial flash
mtd: maps: gpio-addr-flash: Convert to gpiod
mtd: maps: gpio-addr-flash: Replace array with an integer
mtd: maps: gpio-addr-flash: Use order instead of size
mtd: spi-nor: fsl-quadspi: Don't let -EINVAL on the bus
mtd: devices: m25p80: Make sure WRITE_EN is issued before each write
mtd: spi-nor: Support controllers with limited TX FIFO size
mtd: spi-nor: cadence-quadspi: Use proper enum for dma_[un]map_single
mtd: spi-nor: parse SFDP Sector Map Parameter Table
mtd: spi-nor: add support to non-uniform SFDP SPI NOR flash memories
mtd: rawnand: marvell: fix the IRQ handler complete() condition
mtd: rawnand: denali: set SPARE_AREA_SKIP_BYTES register to 8 if unset
mtd: rawnand: r852: fix spelling mistake "card_registred" -> "card_registered"
mtd: rawnand: toshiba: Pass a single nand_chip object to the status helper
mtd: maps: gpio-addr-flash: Use devm_* functions
mtd: maps: gpio-addr-flash: Fix ioremapped size
mtd: maps: gpio-addr-flash: Replace custom printk
mtd: physmap_of: Release resources on error
...
- Two batchs of cleanups of the NAND API, including:
* Deprecating a lot of interfaces (now replaced by ->exec_op()).
* Moving code in separate drivers (JEDEC, ONFI), in private files
(internals), in platform drivers, etc.
* Functions/structures reordering.
* Exclusive use of the nand_chip structure instead of the MTD one
all across the subsystem.
- Addition of the nand_wait_readrdy/rdy_op() helpers.
Raw NAND controllers drivers changes:
- Various coccinelle patches.
- Marvell:
* Use regmap_update_bits() for syscon access.
* More documentation.
* BCH failure path rework.
* More layouts to be supported.
* IRQ handler complete() condition fixed.
- Fsl_ifc:
* SRAM initialization fixed for newer controller versions.
- Denali:
* Fix licenses mismatch and use a SPDX tag.
* Set SPARE_AREA_SKIP_BYTES register to 8 if unset.
- Qualcomm:
* Do not include dma-direct.h.
- Docg4:
* Removed.
- Ams-delta:
* Use of a GPIO lookup table
* Internal machinery changes.
Raw NAND chip drivers changes:
- Toshiba:
* Add support for Toshiba memory BENAND
* Pass a single nand_chip object to the status helper.
- ESMT:
* New driver to retrieve the ECC requirements from the 5th ID byte.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAlvDdvgACgkQJWrqGEe9
VoQ0zQf/QfXYjLDbC/1FXckEkEeVZPRbXQMf+ptdTo0inJefy9LMOvhRKmuABCxn
wwPa99aqQ+aHESnU/s2d8FUrhNRUf35lmRIAP512lJk79tBfgo73l5WSc6UTg6hO
w3KbigOvTi7wCKQYGDFOBZuoFFCvpNsIEtWFuodCbYG1GmeAaL7L2fhbri9JbcE2
zPqmCv0w5BUrPR7i/taI5gD+KDtRdmCEyfb7wQoJy2XZVO0SKqGsBhDhYWqwCpck
eP2UzQ4cFT8X1S0/AfUpbowc6cftdqIwW9VRY4inx3ALQ+sKxrkJ+0E3gL9lnZ+F
p/is0gTdvDmnOjXfwGcL7GXGy0nN8Q==
=EKv1
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.20' of git://git.infradead.org/linux-mtd into mtd/next
NAND core changes:
- Two batchs of cleanups of the NAND API, including:
* Deprecating a lot of interfaces (now replaced by ->exec_op()).
* Moving code in separate drivers (JEDEC, ONFI), in private files
(internals), in platform drivers, etc.
* Functions/structures reordering.
* Exclusive use of the nand_chip structure instead of the MTD one
all across the subsystem.
- Addition of the nand_wait_readrdy/rdy_op() helpers.
Raw NAND controllers drivers changes:
- Various coccinelle patches.
- Marvell:
* Use regmap_update_bits() for syscon access.
* More documentation.
* BCH failure path rework.
* More layouts to be supported.
* IRQ handler complete() condition fixed.
- Fsl_ifc:
* SRAM initialization fixed for newer controller versions.
- Denali:
* Fix licenses mismatch and use a SPDX tag.
* Set SPARE_AREA_SKIP_BYTES register to 8 if unset.
- Qualcomm:
* Do not include dma-direct.h.
- Docg4:
* Removed.
- Ams-delta:
* Use of a GPIO lookup table
* Internal machinery changes.
Raw NAND chip drivers changes:
- Toshiba:
* Add support for Toshiba memory BENAND
* Pass a single nand_chip object to the status helper.
- ESMT:
* New driver to retrieve the ECC requirements from the 5th ID byte.
Straight forward conversion, using an internal list to enable the
driver to pull requests at will.
Dynamically allocate the tag set to avoid having to pull in the
block headers for blktrans.h, since various mtd drivers use
block conflicting names for defines and functions.
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Tested-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add support for the SFDP (JESD216B) Sector Map Parameter Table. This
table is optional, but when available, we parse it to identify the
location and size of sectors within the main data array of the
flash memory device and to identify which Erase Types are supported by
each sector.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Based on Cyrille Pitchen's patch https://lkml.org/lkml/2017/3/22/935.
This patch is a transitional patch in introducing the support of
SFDP SPI memories with non-uniform erase sizes like Spansion s25fs512s.
Non-uniform erase maps will be used later when initialized based on the
SFDP data.
Introduce the memory erase map which splits the memory array into one
or many erase regions. Each erase region supports up to 4 erase types,
as defined by the JEDEC JESD216B (SFDP) specification.
To be backward compatible, the erase map of uniform SPI NOR flash memories
is initialized so it contains only one erase region and this erase region
supports only one erase command. Hence a single size is used to erase any
sector/block of the memory.
Besides, since the algorithm used to erase sectors on non-uniform SPI NOR
flash memories is quite expensive, when possible, the erase map is tuned
to come back to the uniform case.
The 'erase with the best command, move forward and repeat' approach was
suggested by Cristian Birsan in a brainstorm session, so:
Suggested-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Currently, the selection of ECC byte ordering for software hamming is
done at compilation time, which doesn't make sense when ECC byte
calculation is done in hardware and byte ordering is forced by the
hardware engine.
In this case, only the correction is done in software and we want to
force the byte-ordering no matter the value of CONFIG_MTD_NAND_ECC_SMC.
This is typically the case for the FSMC (Smart Media ordering), TMIO and
TXX9NDFMC (regular byte ordering) blocks.
For all other use cases (pure software implementation, SM FTL and
nandecctest), we keep selecting the byte ordering based on the
CONFIG_MTD_NAND_ECC_SMC value. It might not be ideal for SM FTL (I'd
expect Smart Media ordering to be employed by the Smart Media FTL), but
this option doesn't seem to be enabled in the existing _defconfig, so
I can't tell setting sm_order to true is the right choice.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This moves JEDEC related code to nand_jedec.c and JEDEC related
struct/macros to include/linux/mtd/jedec.h.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This moves ONFI related code to nand_onfi.c and ONFI related
struct/macros to include/linux/mtd/onfi.h.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
A lot of things defined in rawnand.h should not be exposed to NAND
controller drivers and should only be shared by core files.
Create the drivers/mtd/nand/raw/internals.h header to store such
definitions, and move all private defs to this header.
Also remove EXPORT_SYMBOLS() on functions that are not supposed to be
exposed.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
onfi_get_async_timing_mode() is only used in one place inside
nand_base.c. Let's inline the code and kill the helper.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
platform_nand_xxx definitions are just used by the plat_nand driver.
Let's move those definitions out of the core/driver-agnostic rawnand.h
header.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Those definitions are not used, let's remove them.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There's already a forward declaration of nand_chip at the beginning of
the file. Get rid of this one.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_scan[with_ids]() have been moved at the end of the file. We can
now get rid of of the nand_flash_dev forward declaration.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Move nand_scan[_with_ids]() and nand_wait_ready() at the end of the
file where all function prototype lies. This will also allow us to get
rid of the nand_flash_dev forward declaration.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The wait timeouts and delays are directly extracted from the NAND
timings and ->chip_delay is only used in legacy path, so let's move it
to the nand_legacy struct to make it clear.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Those hooks should be replaced by a proper ->exec_op() implementation.
Move them to the nand_legacy struct to make it clear.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The ->erase() hook have been overloaded by some drivers for bad reasons:
either the driver was not fitting in the NAND framework and should have
been an MTD driver (docg4), or the driver uses a specific path for the
ERASE operation (denali), instead of implementing it generically.
In any case, we should discourage people from overloading this method
and encourage them to implement ->exec_op() instead.
Move the ->erase() hook to the nand_legacy struct to make it clear.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Those hooks have been overloaded by some drivers for bad reasons:
either the driver was not fitting in the NAND framework and should
have been an MTD driver (docg4), or it was not properly implementing
the OOB read/write request or had a weird layout where BBM are trashed.
In any case, we should discourage people from overloading those
methods and encourage them to fix their driver instead.
Move the ->block_{bad,markbad}() hooks to the nand_legacy struct to
make it clear.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Those hooks have been replaced by ->exec_op(). Move them to the
nand_legacy struct.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Those hooks have been replaced by ->exec_op(). Move them to the
nand_legacy struct.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
All those hooks have been replaced by ->exec_op(). Move them to the
nand_legacy struct.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We regularly have new NAND controller drivers that are making use of
fields/hooks that we want to get rid of but can't because of all the
legacy drivers that we might break if we do.
So, instead of removing those fields/hooks, let's move them to a
sub-struct which is clearly documented as deprecated.
We start with the ->IO_ADDR_{R,W] fields.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There's no good reason to make maxchips a signed integer, since only
positive values are valid. Make it an unsigned int.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the nand_erase_nand() helper.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the nand_xxx_bbt() helpers.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->setup_data_interface() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->setup_read_retry() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->{get,set}_features() hooks.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->erase() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->waitfunc() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->cmdfunc() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->dev_ready() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->cmd_ctrl() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all chip->block_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->select_chip() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all chip->write_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all chip->read_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all ecc->write_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all ecc->read_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one.
Now is ecc->correct()'s turn.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one.
Now is ecc->calculate()'s turn.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one.
Now is ecc->hwctl()'s turn.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers to
take a nand_chip object instead of an mtd_info one.
Now is nand_wait_ready()'s turn.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers to
take a nand_chip object instead of an mtd_info one.
Now is nand_release()'s turn.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers to take
a nand_chip object instead of an mtd_info one.
We start with nand_scan().
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
In order to do that, we first need to update the platform_nand_ctrl
hooks to take a nand_chip object instead of an mtd_info.
We add temporary plat_nand_xxx() wrappers to the do the mtd -> chip
conversion, but those will be dropped when patching nand_chip hooks to
take a nand_chip object.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit c120e75e0e ("mtd: nand: use read_oob() instead of cmdfunc()
for bad block check") removed this only user of the ->read_word()
method but kept the hook in place. Remove it now.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
- Apply reset hacks only when reset is explicitly marked as broken in
the DT
Driver changes:
- Minor cleanup/fixes in the m25p80 driver
- Release flash_np in the nxp-spifi driver
- Add suspend/resume hooks to the atmel-quadspi driver
- Include gpio/consumer.h instead of gpio.h in the atmel-quadspi driver
- Use %pK instead of %p in the stm32-quadspi driver
- Improve timeout handling in the cadence-quadspi driver
- Use mtd_device_register() instead of mtd_device_parse_register() in
the intel-spi driver
-----BEGIN PGP SIGNATURE-----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=uNJl
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-4.19' of git://git.infradead.org/linux-mtd into mtd/next
Pull SPI NOR updates from Boris Brezillon:
"
Core changes:
- Apply reset hacks only when reset is explicitly marked as broken in
the DT
Driver changes:
- Minor cleanup/fixes in the m25p80 driver
- Release flash_np in the nxp-spifi driver
- Add suspend/resume hooks to the atmel-quadspi driver
- Include gpio/consumer.h instead of gpio.h in the atmel-quadspi driver
- Use %pK instead of %p in the stm32-quadspi driver
- Improve timeout handling in the cadence-quadspi driver
- Use mtd_device_register() instead of mtd_device_parse_register() in
the intel-spi driver
"
- Add the SPI-NAND framework.
- Create a helper to find the best ECC configuration.
- Create NAND controller operations.
- Allocate dynamically ONFI parameters structure.
- Add defines for ONFI version bits.
- Add manufacturer fixup for ONFI parameter page.
- Add an option to specify NAND chip as a boot device.
- Add Reed-Solomon error correction algorithm.
- Better name for the controller structure.
- Remove unused caller_is_module() definition.
- Make subop helpers return unsigned values.
- Expose _notsupp() helpers for raw page accessors.
- Add default values for dynamic timings.
- Kill the chip->scan_bbt() hook.
- Rename nand_default_bbt() into nand_create_bbt().
- Start to clean the nand_chip structure.
- Remove stale prototype from rawnand.h.
Raw NAND controllers drivers changes:
- Qcom: structuring cleanup.
- Denali: use core helper to find the best ECC configuration.
- Possible build of almost all drivers by adding a dependency on
COMPILE_TEST for almost all of them in Kconfig, implies various
fixes, Kconfig cleanup, GPIO headers inclusion cleanup, and even
changes in sparc64 and ia64 architectures.
- Clean the ->probe() functions error path of a lot of drivers.
- Migrate all drivers to use nand_scan() instead of
nand_scan_ident()/nand_scan_tail() pair.
- Use mtd_device_register() where applicable to simplify the code.
- Marvell:
* Handle on-die ECC.
* Better clocks handling.
* Remove bogus comment.
* Add suspend and resume support.
- Tegra: add NAND controller driver.
- Atmel:
* Add module param to avoid using dma.
* Drop Wenyou Yang from MAINTAINERS.
- Denali: optimize timings handling.
- FSMC: Stop using chip->read_buf().
- FSL:
* Switch to SPDX license tag identifiers.
* Fix qualifiers in MXC init functions.
Raw NAND chip drivers changes:
- Micron:
* Add fixup for ONFI revision.
* Update ecc_stats.corrected.
* Make ECC activation stateful.
* Avoid enabling/disabling ECC when it can't be disabled.
* Get the actual number of bitflips.
* Allow forced on-die ECC.
* Support 8/512 on-die ECC.
* Fix on-die ECC detection logic.
- Hynix:
* Fix decoding the OOB size on H27UCG8T2BTR.
* Use ->exec_op() in hynix_nand_reg_write_op().
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJbYYGVAAoJECVq6hhHvVaE0poIAJy+VpZl0jTPQ/oO8TQui9hE
IZbc8LwohCvegYYhiY1cNESyMYamDfoK6M93i/0zTJF2AJAxPl25ldT8N5Wr16DO
5Vfsdjv75V8l0JEY2SvWYmC6glOAYs0UEDdcFNJRMPqUnQz+VvBIafJOCQqzo4ZH
SDnLx3XzOxO4PAPnztWEg50WvaqMPt7ThcqoxThHMcQaLrNjgJUsV0mN+vNEv16Q
6gH6hl1C019k+Kj2Zu0vAifHw1K7gIYT4HvqKwstQ6HYUX2IzIzuEpRIcIze0S5z
XKzZ57USItb3l+Y3YwFBLjgP4N+VTT5X59LxdtCOXJ+YvzgxwtKElRvalNcryYI=
=zkEf
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.19' of git://git.infradead.org/linux-mtd into mtd/next
Pull NAND updates from Miquel Raynal:
"
NAND core changes:
- Add the SPI-NAND framework.
- Create a helper to find the best ECC configuration.
- Create NAND controller operations.
- Allocate dynamically ONFI parameters structure.
- Add defines for ONFI version bits.
- Add manufacturer fixup for ONFI parameter page.
- Add an option to specify NAND chip as a boot device.
- Add Reed-Solomon error correction algorithm.
- Better name for the controller structure.
- Remove unused caller_is_module() definition.
- Make subop helpers return unsigned values.
- Expose _notsupp() helpers for raw page accessors.
- Add default values for dynamic timings.
- Kill the chip->scan_bbt() hook.
- Rename nand_default_bbt() into nand_create_bbt().
- Start to clean the nand_chip structure.
- Remove stale prototype from rawnand.h.
Raw NAND controllers drivers changes:
- Qcom: structuring cleanup.
- Denali: use core helper to find the best ECC configuration.
- Possible build of almost all drivers by adding a dependency on
COMPILE_TEST for almost all of them in Kconfig, implies various
fixes, Kconfig cleanup, GPIO headers inclusion cleanup, and even
changes in sparc64 and ia64 architectures.
- Clean the ->probe() functions error path of a lot of drivers.
- Migrate all drivers to use nand_scan() instead of
nand_scan_ident()/nand_scan_tail() pair.
- Use mtd_device_register() where applicable to simplify the code.
- Marvell:
* Handle on-die ECC.
* Better clocks handling.
* Remove bogus comment.
* Add suspend and resume support.
- Tegra: add NAND controller driver.
- Atmel:
* Add module param to avoid using dma.
* Drop Wenyou Yang from MAINTAINERS.
- Denali: optimize timings handling.
- FSMC: Stop using chip->read_buf().
- FSL:
* Switch to SPDX license tag identifiers.
* Fix qualifiers in MXC init functions.
Raw NAND chip drivers changes:
- Micron:
* Add fixup for ONFI revision.
* Update ecc_stats.corrected.
* Make ECC activation stateful.
* Avoid enabling/disabling ECC when it can't be disabled.
* Get the actual number of bitflips.
* Allow forced on-die ECC.
* Support 8/512 on-die ECC.
* Fix on-die ECC detection logic.
- Hynix:
* Fix decoding the OOB size on H27UCG8T2BTR.
* Use ->exec_op() in hynix_nand_reg_write_op().
"
Now that it is possible to do dynamic allocations during the
identification phase, convert the onfi_params structure (which is only
needed with ONFI compliant chips) into a pointer that will be allocated
only if needed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Commit 59b356ffd0 ("mtd: m25p80: restore the status of SPI flash when
exiting") is the latest from a long history of attempts to add reboot
handling to handle stateful addressing modes on SPI flash. Some prior
mostly-related discussions:
http://lists.infradead.org/pipermail/linux-mtd/2013-March/046343.html
[PATCH 1/3] mtd: m25p80: utilize dedicated 4-byte addressing commands
http://lists.infradead.org/pipermail/barebox/2014-September/020682.html
[RFC] MTD m25p80 3-byte addressing and boot problem
http://lists.infradead.org/pipermail/linux-mtd/2015-February/057683.html
[PATCH 2/2] m25p80: if supported put chip to deep power down if not used
Previously, attempts to add reboot-time software reset handling were
rejected, but the latest attempt was not.
Quick summary of the problem:
Some systems (e.g., boot ROM or bootloader) assume that they can read
initial boot code from their SPI flash using 3-byte addressing. If the
flash is left in 4-byte mode after reset, these systems won't boot. The
above patch provided a shutdown/remove hook to attempt to reset the
addressing mode before we reboot. Notably, this patch misses out on
huge classes of unexpected reboots (e.g., crashes, watchdog resets).
Unfortunately, it is essentially impossible to solve this problem 100%:
if your system doesn't know how to reset the SPI flash to power-on
defaults at initialization time, no amount of software can really rescue
you -- there will always be a chance of some unexpected reset that
leaves your flash in an addressing mode that your boot sequence didn't
expect.
While it is not directly harmful to perform hacks like the
aforementioned commit on all 4-byte addressing flash, a
properly-designed system should not need the hack -- and in fact,
providing this hack may mask the fact that a given system is indeed
broken. So this patch attempts to apply this unsound hack more narrowly,
providing a strong suggestion to developers and system designers that
this is truly a hack. With luck, system designers can catch their errors
early on in their development cycle, rather than applying this hack long
term. But apparently enough systems are out in the wild that we still
have to provide this hack.
Document a new device tree property to denote systems that do not have a
proper hardware (or software) reset mechanism, and apply the hack (with
a loud warning) only in this case.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Thanks to the migration of all drivers to use nand_scan() and the
related nand_controller_ops, we can now allocate data during the
detection phase. Let's do it first for the NAND model parameter which
is allocated in nand_detect().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Both nand_scan_ident() and nand_scan_tail() helpers used to be called
directly from controller drivers that needed to tweak some ECC-related
parameters before nand_scan_tail(). This separation prevented dynamic
allocations during the phase of NAND identification, which was
inconvenient.
All controller drivers have been moved to use nand_scan(), in
conjunction with the chip->ecc.[attach|detach]_chip() hooks that
actually do the required tweaking sequence between both ident/tail
calls, allowing programmers to use dynamic allocation as they need all
across the scanning sequence.
Declare nand_scan_[ident|tail]() statically now.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
In order to remove the limitation that forbids dynamic allocation in
nand_scan_ident(), we must create a path that will be the same for all
controller drivers. The idea is to use nand_scan() instead of the widely
used nand_scan_ident()/nand_scan_tail() couple. In order to achieve
this, controller drivers will need to adjust some parameters between
these two functions depending on the NAND chip wired on them.
This takes the form of two new hooks (->{attach,detach}_chip()) that are
placed in a new nand_controller_ops structure, which is then attached
to the nand_controller object at driver initialization time.
->attach_chip() is called between nand_scan_ident() and
nand_scan_tail(), and ->detach_chip() is called in the error path of
nand_scan() and in nand_cleanup().
Note that some NAND controller drivers don't have a dedicated
nand_controller object and instead rely on the default/dummy one
embedded in nand_chip. If you're in this case and still want to
initialize the controller ops, you'll have to manipulate
chip->dummy_controller directly.
Last but not least, it's worth mentioning that we plan to move some of
the controller related hooks placed in nand_chip into
nand_controller_ops to make the separation between NAND chip and NAND
controller methods clearer.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
In the raw NAND core, a NAND chip is described by a nand_chip structure,
while a NAND controller is described with a nand_hw_control structure
which is not very meaningful.
Rename this structure nand_controller.
As the structure gets renamed, it is logical to also rename the core
function initializing it from nand_hw_control_init() to
nand_controller_init().
Lastly, the 'hwcontrol' entry of the nand_chip structure is not
meaningful neither while it has the role of fallback when no controller
structure is provided by the driver (the controller driver is dumb and
can only control a single chip). Thus, it is renamed dummy_controller.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
A report from Colin Ian King pointed a CoverityScan issue where error
values on these helpers where not checked in the drivers. These
helpers can error out only in case of a software bug in driver code,
not because of a runtime/hardware error. Hence, let's WARN_ON() in this
case and return 0 which is harmless anyway.
Fixes: 8878b126df ("mtd: nand: add ->exec_op() implementation")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some implementations simply can't disable their ECC engine. Expose
helpers returning -ENOTSUPP so that the caller knows that raw accesses
are not supported instead of silently falling back to non-raw
accessors.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
A comment in the kernel doc of the mtd_oob_ops structure tells that it
is not possible to write more than one page with OOB. This is actually
true for only a few MTD devices like 'onenand' but it is definitely not
a general limitation. While this would benefit to be handled elsewhere
either by the MTD layer or by the limited drivers, let's update this
comment to reflect the reality.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
None of the board files are overloading those hooks, so let's drop them
from struct platform_nand_ctrl.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
None of the existing drivers are overloading the ->scan_bbt() method,
let's get rid of it and replace calls to ->scan_bbt() by
nand_create_bbt() ones.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Rename nand_default_bbt() into nand_create_bbt() and pass it a nand_chip
object to prepare removal of the chip->scan_bbt() hook.
We add a temporary nand_default_bbt() wrapper which will be dropped
after the removal of ->scan_bbt().
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
struct device_node is defined in linux/of.h. Let's include this file
instead of having a forward declaration of this struct.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
struct mtd_info is defined in linux/mtd/mtd.h which is included
at the beginning of nand_base.c, there's thus no need for the
forward declaration of mtd_info.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_do_read() is a static function implemented in nand_base.c. There's
no good reason to expose its prototype in rawnand.h.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add minimal support for the MX35LF1GE4AB SPI NAND chip.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add support for the W25M02GV chip.
Signed-off-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add a basic driver for Micron SPI NANDs. Only one device is supported
right now, but the driver will be extended to support more devices
afterwards.
Signed-off-by: Peter Pan <peterpandong@micron.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add a SPI NAND framework based on the generic NAND framework and the
spi-mem infrastructure.
In its current state, this framework supports the following features:
- single/dual/quad IO modes
- on-die ECC
Signed-off-by: Peter Pan <peterpandong@micron.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Function nand_ecc_choose_conf() will be help for all the cases, so
other helper functions can be made static.
nand_check_ecc_caps(): Invoke nand_ecc_choose_conf() with
both chip->ecc.size and chip->ecc.strength
value set.
nand_maximize_ecc(): Invoke nand_ecc_choose_conf() with
NAND_ECC_MAXIMIZE flag.
nand_match_ecc_req(): Invoke nand_ecc_choose_conf() with either
chip->ecc.size or chip->ecc.strength value
set and without NAND_ECC_MAXIMIZE flag.
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
commit 2c8f8afa7f ("mtd: nand: add generic helpers to check,
match, maximize ECC settings") provides generic helpers which
drivers can use for setting up ECC parameters.
Since same board can have different ECC strength nand chips so
following is the logic for setting up ECC strength and ECC step
size, which can be used by most of the drivers.
1. If both ECC step size and ECC strength are already set
(usually by DT) then just check whether this setting
is supported by NAND controller.
2. If NAND_ECC_MAXIMIZE is set, then select maximum ECC strength
supported by NAND controller.
3. Otherwise, try to match the ECC step size and ECC strength closest
to the chip's requirement. If available OOB size can't fit the chip
requirement then select maximum ECC strength which can be fit with
available OOB size.
This patch introduces nand_ecc_choose_conf function which calls the
required helper functions for the above logic. The drivers can use
this single function instead of calling the 3 helper functions
individually.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add defines for the ONFI version bits and use them in
nand_flash_detect_onfi().
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This is called after the ONFI parameter page checksum is verified
and allows us to override the contents of the parameter page.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Allow to define a NAND chip as a boot device. This can be helpful
for the selection of the ECC algorithm and strength in case the boot
ROM supports only a subset of controller provided options.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add Reed-Solomon (RS) to the enumeration of ECC algorithms.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Core changes:
- Add a sysfs attribute to expose available OOB size
Driver changes:
- Remove HAS_DMA dependency on various drivers
- Use dev_get_drvdata() instead of platform_get_drvdata() in docg3
- Replace msleep by usleep_range() in the dataflash driver
- Avoid VLA usage in nftl layers
- Remove useless .owner assignment in pismo
- Fix various issues in the CFI driver
- Improve TRX partition handling expose a DT compat for this part
parser
- Clarify OFFSET_CONTINUOUS meaning
NAND changes:
Core changes:
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
ONFI spec
Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
* Cleanup/simplification of a few aspects in the driver
* Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
* Use of_device_get_match_data() instead of of_match_device()
* Add an entry in MAINTAINERS for this driver
* Fix nand-ecc-step-size and nand-ecc-strength description in the DT
bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()
SPI NOR changes:
Core changes:
- Add support for a bunch of SPI NOR chips
- Clear EAR reg when switching to 3-byte addressing mode on Winbond
chips
SPI NOR controller driver changes:
- cadence: Add DMA support for direct mode reads
- hisi: Prefix a few functions with hisi_
- intel:
* Mark the driver as "dangerous" in Kconfig
* Fix atomic sequence handling
* Pass a 40us delay (instead of 0us) to readl_poll_timeout()
- fsl:
* fix a typo in a function name
* add support for IP variants embedded in the ls2080a and ls1080a
SoCs
- stm32: request exclusive control of the reset line
-----BEGIN PGP SIGNATURE-----
iQI5BAABCAAjBQJbGZ/KHBxib3Jpcy5icmV6aWxsb25AYm9vdGxpbi5jb20ACgkQ
Ze02AX4ItwBhLRAAqj0wXUjyO836NSqYboF21b+eLCLAOojydRCIQjbMYkEQ1ifZ
vLEwHy8vDYYnJyT+cXlP8wpImh7grhCrq3jPW/SDU2xljUC4TXAAVrfSYw6EJ5at
TJBum4+DVkTr3ZgBUI/RxDmao0i+29ztK/viHnLEeDziWaFGJqy0C8FtMwFf6MTF
LwbmCD0KppoLUP0CW/V+fITu8+FBOFsLdDXUi//GIIMeUE3smvGbhXrRZsFoXC3p
5sgo6Dn3f87uO/fK2x2YNf9uXAb2fRuqnCmXwu+AXEW1NLBzkU0TlxerPxbbrmAR
wNqBRK/mw+uIILAZgi8tiCRreFYGNNefK+cpf7lqFpZVgBWJJxBMkfy1UdXupUQx
N/2J+UpGKlGtevvW1CnTXvK0zeXg8FwGREXL4il02Sg57s7IkvG/xIoSN2Nofs9K
KULDJ8CE1BtH/LwdKHpe7DLzc1I3E8DRzzbVzEzZuW/ukMnqCgouF4wNsjmUJHmm
KfCNan8CWCU6QyqVIGd3ucm5RXwwaEiMrXxoCmjmkJy8+4eDTYNWgruFSU/adOtU
lABuvzVzoJ3UKvdxjlirg83EcWrazj4W2/COz+Hpxaa+vAwAPb1GoxyNKqGpdL8p
lugJOps4rHuFF6xJX/AwSrL5C1cmpuKXICqkErTieKT1YZhpx72v7rFXEK4=
=cHjU
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"Core changes:
- Add a sysfs attribute to expose available OOB size
Driver changes:
- Remove HAS_DMA dependency on various drivers
- Use dev_get_drvdata() instead of platform_get_drvdata() in docg3
- Replace msleep by usleep_range() in the dataflash driver
- Avoid VLA usage in nftl layers
- Remove useless .owner assignment in pismo
- Fix various issues in the CFI driver
- Improve TRX partition handling expose a DT compat for this part
parser
- Clarify OFFSET_CONTINUOUS meaning
NAND core changes:
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
ONFI spec
Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
+ Cleanup/simplification of a few aspects in the driver
+ Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
+ Use of_device_get_match_data() instead of of_match_device()
+ Add an entry in MAINTAINERS for this driver
+ Fix nand-ecc-step-size and nand-ecc-strength description in the
DT bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()
SPI NOR core changes:
- Add support for a bunch of SPI NOR chips
- Clear EAR reg when switching to 3-byte addressing mode on Winbond
chips
SPI NOR controller driver changes:
- cadence: Add DMA support for direct mode reads
- hisi: Prefix a few functions with hisi_
- intel:
+ Mark the driver as "dangerous" in Kconfig
+ Fix atomic sequence handling
+ Pass a 40us delay (instead of 0us) to readl_poll_timeout()
- fsl:
+ fix a typo in a function name
+ add support for IP variants embedded in the ls2080a and ls1080a
SoCs
- stm32: request exclusive control of the reset line"
* tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd: (66 commits)
mtd: nand: Pass mode information to nand_page_io_req
mtd: cfi_cmdset_0002: Change erase one block to enable XIP once
mtd: cfi_cmdset_0002: Change erase functions to check chip good only
mtd: cfi_cmdset_0002: Change erase functions to retry for error
mtd: cfi_cmdset_0002: Change definition naming to retry write operation
mtd: cfi_cmdset_0002: Change write buffer to check correct value
mtd: cmdlinepart: Update comment for introduction of OFFSET_CONTINUOUS
mtd: bcm47xxpart: add of_match_table with a new DT binding
dt-bindings: mtd: document Broadcom's BCM47xx partitions
mtd: spi-nor: Add support for EN25QH32
mtd: spi-nor: Add support for is25wp series chips
mtd: spi-nor: Add Winbond w25q32jv support
mtd: spi-nor: fsl-quadspi: add support for ls2080a/ls1080a
mtd: spi-nor: stm32-quadspi: explicitly request exclusive reset control
mtd: spi-nor: intel: provide a range for poll_timout
mtd: spi-nor: fsl-quadspi: fix api naming typo _init_ahb_read
mtd: spi-nor: intel-spi: Explicitly mark the driver as dangerous in Kconfig
mtd: spi-nor: intel-spi: Fix atomic sequence handling
mtd: rawnand: Do not check FAIL bit when executing a SET_FEATURES op
mtd: rawnand: use bit-wise majority to recover the ONFI param page
...
- Add support for a bunch of SPI NOR chips
- Clear EAR reg when switching to 3-byte addressing mode on Winbond
chips
SPI NOR controller driver changes:
- cadence: Add DMA support for direct mode reads
- hisi: Prefix a few functions with hisi_
- intel:
* Mark the driver as "dangerous" in Kconfig
* Fix atomic sequence handling
* Pass a 40us delay (instead of 0us) to readl_poll_timeout()
- fsl:
* fix a typo in a function name
* add support for IP variants embedded in the ls2080a and ls1080a
SoCs
- stm32: request exclusive control of the reset line
-----BEGIN PGP SIGNATURE-----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=eIAQ
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-4.18' of git://git.infradead.org/linux-mtd into mtd/next
Core changes:
- Add support for a bunch of SPI NOR chips
- Clear EAR reg when switching to 3-byte addressing mode on Winbond
chips
SPI NOR controller driver changes:
- cadence: Add DMA support for direct mode reads
- hisi: Prefix a few functions with hisi_
- intel:
* Mark the driver as "dangerous" in Kconfig
* Fix atomic sequence handling
* Pass a 40us delay (instead of 0us) to readl_poll_timeout()
- fsl:
* fix a typo in a function name
* add support for IP variants embedded in the ls2080a and ls1080a
SoCs
- stm32: request exclusive control of the reset line
The NAND sub-layers are likely to need the MTD_OPS_XXX mode information
in order to decide if they should enable/disable ECC or how they should
place the OOB bytes in the provided OOB buffer.
Add a field to nand_page_io_req to pass this information.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@exceet.de>
The __DIVIDE() macro checks whether it is called with a 32-bit or 64-bit
dividend, to select the appropriate divide-and-round-up routine.
As the check uses the ternary operator, the result will always be
promoted to a type that can hold both results, i.e. unsigned long long.
When using this result in a division on a 32-bit system, this may lead
to link errors like:
ERROR: "__udivdi3" [drivers/mtd/nand/raw/nand.ko] undefined!
Fix this by casting the result of the division to the type of the
dividend.
Fixes: 8878b126df ("mtd: nand: add ->exec_op() implementation")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Commit 9e343e87d2 ("mtd: cfi: convert inline functions to macros")
changed map_word_andequal() into a macro, but also changed the right
hand side of the comparison from val3 to val2. Change it back to use
val3 on the right hand side.
Thankfully this did not cause a regression because all callers
currently pass the same argument for val2 and val3.
Fixes: 9e343e87d2 ("mtd: cfi: convert inline functions to macros")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Gets rid of those warnings and better document the parameters.
./include/linux/mtd/rawnand.h:752: warning: Function parameter or member 'timings.sdr' not described in 'nand_data_interface'
./include/linux/mtd/rawnand.h:817: warning: Function parameter or member 'buf' not described in 'nand_op_data_instr'
./include/linux/mtd/rawnand.h:817: warning: Function parameter or member 'buf.in' not described in 'nand_op_data_instr'
./include/linux/mtd/rawnand.h:817: warning: Function parameter or member 'buf.out' not described in 'nand_op_data_instr'
./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx' not described in 'nand_op_instr'
./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.cmd' not described in 'nand_op_instr'
./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.addr' not described in 'nand_op_instr'
./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.data' not described in 'nand_op_instr'
./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.waitrdy' not described in 'nand_op_instr'
./include/linux/mtd/rawnand.h:1010: warning: Function parameter or member 'ctx' not described in 'nand_op_parser_pattern_elem'
./include/linux/mtd/rawnand.h:1010: warning: Function parameter or member 'ctx.addr' not described in 'nand_op_parser_pattern_elem'
./include/linux/mtd/rawnand.h:1010: warning: Function parameter or member 'ctx.data' not described in 'nand_op_parser_pattern_elem'
./include/linux/mtd/rawnand.h:1313: warning: Function parameter or member 'manufacturer.desc' not described in 'nand_chip'
./include/linux/mtd/rawnand.h:1313: warning: Function parameter or member 'manufacturer.priv' not described in 'nand_chip'
./include/linux/mtd/rawnand.h:848: WARNING: Unexpected indentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
As part of the work of migrating all the drivers to nand_scan(), and
because nand_scan() does not provide a way to pass an ID table, rename
the function nand_scan_with_ids() and add a third parameter to give a
flash ID table (like what was done with nand_scan_ident()).
Create a nand_scan() helper that is just a wrapper of
nand_scan_with_ids(), passing NULL as the ID table. This way a
controller drivers can continue using nand_scan() transparently.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Currently it is possible to read and/or write to suspend EB's.
Writing /dev/mtdX or /dev/mtdblockX from several processes may
break the flash state machine.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Winbond spi-nor flash 32MB and larger have an 'Extended Address
Register' as one option for addressing beyond 16MB (Macronix
has the same concept, Spansion has EXTADD bits in the Bank Address
Register).
According to section
8.2.7 Write Extended Address Register (C5h)
of the Winbond W25Q256FV data sheet (256M-BIT SPI flash)
The Extended Address Register is only effective when the device is
in the 3-Byte Address Mode. When the device operates in the 4-Byte
Address Mode (ADS=1), any command with address input of A31-A24
will replace the Extended Address Register values. It is
recommended to check and update the Extended Address Register if
necessary when the device is switched from 4-Byte to 3-Byte Address
Mode.
So the documentation suggests clearing the EAR after switching to
3-byte mode. Experimentation shows that the EAR is *always* one after
the switch to 3-byte mode, so clearing the EAR is mandatory at
shutdown for a subsequent 3-byte-addressed reboot to work.
Note that some SOCs (e.g. MT7621) do not assert a reset line at normal
reboot, so we cannot rely on hardware reset. The MT7621 does assert a
reset line at watchdog-reset.
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
* Prepare arrival of the SPI NAND subsystem by implementing a generic
(interface-agnostic) layer to ease manipulation of NAND devices
* Move onenand code base to the drivers/mtd/nand/ dir
* Rework timing mode selection
* Provide a generic way for NAND chip drivers to flag a specific
GET/SET FEATURE operation as supported/unsupported
* Stop embedding ONFI/JEDEC param page in nand_chip
Driver changes:
* Rework/cleanup of the mxc driver
* Various cleanups in the vf610 driver
* Migrate the fsmc and vf610 to ->exec_op()
* Get rid of the pxa driver (replaced by marvell_nand)
* Support ->setup_data_interface() in the GPMI driver
* Fix probe error path in several drivers
* Remove support for unused hw_syndrome mode in sunxi_nand
* Various minor improvements
-----BEGIN PGP SIGNATURE-----
iQI5BAABCAAjBQJavURPHBxib3Jpcy5icmV6aWxsb25AYm9vdGxpbi5jb20ACgkQ
Ze02AX4ItwDzsw//YqnrDG6JzEBGEEJ0c1I6O/2Zk9eDrXhDeKk2S4G292QGQ4by
8bKYpHo3al9TxTBb/to6+BexoP717tSwbn+AcW5W2YqGpIAeSGaw1POGau9E7l71
wQh1aECOXCpLVLKbv/JFspiKMJYj+irxoTjdR6/3FjawDx0ruLwCCLlvOFlfkUOM
ESv+hZv9364jcq/SsydYTYaIc95IsfBOUZVYcXRRdtaI7hvD9ljfXRSGNh+Guovc
Bmvyiv9VuUBRg/v26gdQjESVfs3k37YV6LfS5eQSPuCHs2WGaZa5S6mBpHunAxTN
bhbd+vVwzMaDSmX29Xsml+isJnmTdBBJRcg4qusY/nBjeUHtY2nj5J3bq+CuhSwj
q2MB6YyBStqeagzBvctt3wzG9S7ZsVGU+PMtpMkH4T8BY+Bff9yFCPmRZwTUOorK
iVuVhS2NImvJZ05/hc9VchAmSqd4PozHM08oW0NC6FqnF63hinkzw0J3K6FXycFF
q/6lioZFHE8qJbD3LhDqCrLJoRDQDpxVQmZP9RCL1iozW7GNIYD7/IrPrsgqSQNa
P10PvPt8lbBNq3GU3mIMtajTVihRJmH4Kdxd2i08dRp4hxIakF9Zx3MOhw5gZc0b
C0xoFgaEvxbyb5P3VGVy7LYTvTfvJ9KsacntTSn7LrIU3D7meXmwnHynq5A=
=uvio
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.17' of git://git.infradead.org/linux-mtd into mtd/next
Core changes:
* Prepare arrival of the SPI NAND subsystem by implementing a generic
(interface-agnostic) layer to ease manipulation of NAND devices
* Move onenand code base to the drivers/mtd/nand/ dir
* Rework timing mode selection
* Provide a generic way for NAND chip drivers to flag a specific
GET/SET FEATURE operation as supported/unsupported
* Stop embedding ONFI/JEDEC param page in nand_chip
Driver changes:
* Rework/cleanup of the mxc driver
* Various cleanups in the vf610 driver
* Migrate the fsmc and vf610 to ->exec_op()
* Get rid of the pxa driver (replaced by marvell_nand)
* Support ->setup_data_interface() in the GPMI driver
* Fix probe error path in several drivers
* Remove support for unused hw_syndrome mode in sunxi_nand
* Various minor improvements
In order to properly support compatibility strings as described in the
bindings/mtd/partition.txt "ofpart" type should be treated as an
indication for looking into OF. MTD should check "compatible" property
and search for a matching parser rather than blindly trying the one
supporting "fixed-partitions".
It also means that existing "fixed-partitions" parser should get renamed
to use a more meaningful name.
This commit achievies that aim by introducing a new mtd_part_of_parse().
It works by looking for a matching parser for every string in the
"compatibility" property (starting with the most specific one).
Please note that driver-specified parsers still take a precedence. It's
assumed that driver providing a parser type has a good reason for that
(e.g. having platform data with device-specific info). Also doing
otherwise could break existing setups. The same applies to using default
parsers (including "cmdlinepart") as some overwrite DT data with cmdline
argument.
Partition parsers can now provide an of_match_table to enable
flash<-->parser matching via device tree as documented in the
mtd/partition.txt.
This support is currently limited to built-in parsers as it uses
request_module() and friends. This should be sufficient for most cases
though as compiling parsers as modules isn't a common choice.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Tested-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
MTD users are no longer checking erase_info->state to determine if the
erase operation failed or succeeded. Moreover, mtd_erase_callback() is
now a NOP.
We can safely get rid of all mtd_erase_callback() calls and all
erase_info->state assignments. While at it, get rid of the
erase_info->state field, all MTD_ERASE_XXX definitions and the
mtd_erase_callback() function.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
---
Changes in v2:
- Address a few coding style issues (reported by Miquel)
- Remove comments that are no longer valid (reported by Miquel)
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
Now that there is a small nand_parameters structure that hold all needed
ONFI parameters, remove the ONFI page from the nand_chip structure by
just allocating it during the identification phase and removing it right
after.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
Now that there is a small nand_parameters structure that can held
generic parameters, remove the JEDEC page from the nand_chip structure
by just allocating it during the identification phase and removing it
right after.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
If SET/GET_FEATURES is available (from the parameter page), use a
bitmap to declare what feature is actually supported.
Initialize the bitmap in the core to support timing changes (only
feature used by the core), also add support for Micron specific features
used in Micron initialization code (in the init routine).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
ONFI-related parameters that will be used outside from the
identification function are stored in a separate onfi_parameters
structure embedded in nand_parameters, this small structure that
already hold generic parameters.
For now, the onfi_parameters structure is allocated statically. However,
after some deep rework in the NAND framework, it will be possible to do
dynamic allocations from the NAND identification phase, and this
strcuture will then be dynamically allocated when needed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
To prepare to the removal of such huge structure, a small NAND parameter
structure is allocated statically and contains only very few members
that are generic to all chips and actually used elsewhere in the code.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Prepare the fact that some features managed by GET/SET_FEATURES could be
overloaded by vendor code. To handle this logic, use new wrappers
instead of directly call the ->get/set_features() hooks.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
SET/GET FEATURES are flagged ONFI-compliant because of their name. This
is not accurate as non-ONFI NAND chips support it and use it.
Rename the hooks and helpers to remove the "onfi" prefix.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
->fail_addr and ->addr can be updated no matter the result of
parent->_erase(), we just need to remove the code doing the same thing
in mtd_erase_callback() to avoid adjusting those fields twice.
Note that this can be done because all MTD users have been converted to
not pass an erase_info->callback() and are thus only taking the
->addr_fail and ->addr fields into account after part_erase() has
returned.
While we're at it, get rid of the erase_info->mtd field which was only
needed to let mtd_erase_callback() get the partition device back.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
None of the mtd->_erase() implementations work in an asynchronous manner,
so let's simplify MTD users that call mtd_erase(). All they need to do
is check the value returned by mtd_erase() and assume that != 0 means
failure.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Some fields are not used by MTD drivers, users or core code. Moreover,
those fields are not documented, so get rid of them to avoid any
confusion.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Add an intermediate layer to abstract NAND device interface so that
some logic can be shared between SPI NANDs, parallel/raw NANDs,
OneNANDs, ...
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Some files add a comment giving the path of the file inside the Linux
tree, which is pretty useless since the reader had to find the file to
open it.
Getting rid of these comments will also allow us to easily move these
files around when needed.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
* Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
* Introduce the ->exec_op() infrastructure
* Rework NAND buffers handling
* Fix ECC requirements for K9F4G08U0D
* Fix nand_do_read_oob() to return the number of bitflips
* Mark K9F1G08U0E as not supporting subpage writes
Driver changes:
* MTK: Rework the driver to support new IP versions
* OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and fix
DT support
* Marvell: Add a new driver to replace the pxa3xx one
-----BEGIN PGP SIGNATURE-----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=TXIU
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.16' of git://git.infradead.org/linux-mtd into mtd/next
Pull NAND changes from Boris Brezillon:
"
Core changes:
* Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
* Introduce the ->exec_op() infrastructure
* Rework NAND buffers handling
* Fix ECC requirements for K9F4G08U0D
* Fix nand_do_read_oob() to return the number of bitflips
* Mark K9F1G08U0E as not supporting subpage writes
Driver changes:
* MTK: Rework the driver to support new IP versions
* OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and fix
DT support
* Marvell: Add a new driver to replace the pxa3xx one
"
Core changes:
* Add support to new ISSI and Cypress/Spansion memory parts.
* Fix support of Micron memories by checking error bits in the FSR.
* Fix update of block-protection bits by reading back the SR.
* Restore the internal state of the SPI flash memory when removing the
device.
Driver changes:
* Maintenance for Freescale, Intel and Metiatek drivers.
* Add support of the direct access mode for the Cadence QSPI controller.
-----BEGIN PGP SIGNATURE-----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=3oDP
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-4.16' of git://git.infradead.org/linux-mtd into mtd/next
Pull spi-nor changes from Cyrille Pitchen:
"
This pull-request contains the following notable changes:
Core changes:
* Add support to new ISSI and Cypress/Spansion memory parts.
* Fix support of Micron memories by checking error bits in the FSR.
* Fix update of block-protection bits by reading back the SR.
* Restore the internal state of the SPI flash memory when removing the
device.
Driver changes:
* Maintenance for Freescale, Intel and Metiatek drivers.
* Add support of the direct access mode for the Cadence QSPI controller.
"
GCC-4.4.4 raises errors when assigning a parameter in an anonymous
union, leading to this kind of failure:
drivers/mtd/nand/marvell_nand.c:1936:
warning: missing braces around initializer
warning: (near initialization for '(anonymous)[1].<anonymous>')
error: unknown field 'data' specified in initializer
error: unknown field 'addr' specified in initializer
Work around the situation by naming these unions.
Fixes: 8878b126df ("mtd: nand: add ->exec_op() implementation")
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Tested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
There's currently nothing forcing alignment of einfo->addr and
einfo->len on mtd->erasesize. Since we don't know if automatically
aligning those field in mtd_erase() will hurt some drivers, we add an
helper function to let drivers that need such an alignment explicitly
ask for it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Miquel Raynal <miquel.raynal@free-electrons.com>
The map_word_() functions, dating back to linux-2.6.8, try to perform
bitwise operations on a 'map_word' structure. This may have worked
with compilers that were current then (gcc-3.4 or earlier), but end
up being rather inefficient on any version I could try now (gcc-4.4 or
higher). Specifically we hit a problem analyzed in gcc PR81715 where we
fail to reuse the stack space for local variables.
This can be seen immediately in the stack consumption for
cfi_staa_erase_varsize() and other functions that (with CONFIG_KASAN)
can be up to 2200 bytes. Changing the inline functions into macros brings
this down to 1280 bytes. Without KASAN, the same problem exists, but
the stack consumption is lower to start with, my patch shrinks it from
920 to 496 bytes on with arm-linux-gnueabi-gcc-5.4, and saves around
1KB in .text size for cfi_cmdset_0020.c, as it avoids copying map_word
structures for each call to one of these helpers.
With the latest gcc-8 snapshot, the problem is fixed in upstream gcc,
but nobody uses that yet, so we should still work around it in mainline
kernels and probably backport the workaround to stable kernels as well.
We had a couple of other functions that suffered from the same gcc bug,
and all of those had a simpler workaround involving dummy variables
in the inline function. Unfortunately that did not work here, the
macro hack was the best I could come up with.
It would also be helpful to have someone to a little performance testing
on the patch, to see how much it helps in terms of CPU utilitzation.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81715
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Introduce a new interface to instruct NAND controllers to send specific
NAND operations. The new interface takes the form of a single method
called ->exec_op(). This method is designed to replace ->cmd_ctrl(),
->cmdfunc() and ->read/write_byte/word/buf() hooks.
->exec_op() is passed a set of instructions describing the operation
to execute. Each instruction has a type (ADDR, CMD, DATA, WAITRDY)
and delay. The delay is here to help simple controllers wait enough
time between each instruction, advanced controllers with integrated
timings control can ignore these delays.
Controllers that natively support complex operations (operations
formed of several instructions) can use the NAND op parser
infrastructure. This infrastructure allows controller drivers to
describe the sequence of instructions they support (called
nand_op_pattern) and a hook for each of these supported sequences. The
core then tries to find the best match for a given NAND operation, and
calls the associated hook.
Various other helpers are also added to ease NAND controller drivers
writing.
This new interface should ease support of vendor specific operations
in that NAND manufacturer drivers now have a way to check if the
controller they are connected to supports a specific operation, and
complain or refuse to probe the NAND chip when that's not the case.
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
struct nand_buffers is malloc'ed in nand_scan_tail() just for
containing three pointers. Squash this struct into nand_chip.
Move and rename as follows:
chip->buffers->ecccalc -> chip->ecc.calc_buf
chip->buffers->ecccode -> chip->ecc.code_buf
chip->buffers->databuf -> chip->data_buf
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The last/only user of NAND_OWN_BUFFERS (cafe_nand.c) has been reworked.
This flag is no longer needed.
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Right now, the chip->data_interface field is populated in
nand_scan_tail(), so after the whole NAND detection has taken place.
This is fine because these timings are not yet used by the core so
early in the probe process, but the situation is about to change with
the introduction of ->exec_op().
Also, by convention, nand_scan_ident() is not supposed to allocate
resources, only nand_scan_tail() can, so this prevent us from
allocating and initializing the data_interface object in
nand_scan_ident().
In order to solve this problem, directly embed a data_interface object
in nand_chip so that we don't have to allocate it, and initialize it to
ONFI SDR mode 0 at the very beginning of nand_scan_ident().
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The core currently send the READ0 and SEQIN+PAGEPROG commands in
nand_do_read/write_ops(). This is inconsistent with
->read/write_oob[_raw]() hooks behavior which are expected to send
these commands.
There's already a flag (NAND_ECC_CUSTOM_PAGE_ACCESS) to inform the core
that a specific controller wants to send the READ/SEQIN+PAGEPROG
commands on its own, but it's an opt-in flag, and existing drivers are
unlikely to be updated to pass it.
Moreover, some controllers cannot dissociate the READ/PAGEPROG commands
from the associated data transfer and ECC engine activation, and
developers have to hack things in their ->cmdfunc() implementation to
handle such complex cases, or have to accept the perf penalty of sending
twice the same command.
To address this problem we are planning on adding a new interface which
is passed all information about a NAND operation (including the amount
of data to transfer) and replacing all calls to ->cmdfunc() to calls to
this new ->exec_op() hook. But, in order to do that, we need to have all
->cmdfunc() calls placed near their associated ->read/write_buf/byte()
calls.
Modify the core and relevant drivers to make NAND_ECC_CUSTOM_PAGE_ACCESS
the default case, and remove this flag.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[miquel.raynal@free-electrons.com: tested, fixed and rebased on nand/next]
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This is part of the process of removing direct calls to ->cmdfunc()
outside of the core in order to introduce a better interface to execute
NAND operations.
Here we provide several helpers and make use of them to remove all
direct calls to ->cmdfunc(). This way, we can easily modify those
helpers to make use of the new ->exec_op() interface when available.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[miquel.raynal@free-electrons.com: rebased and fixed some conflicts]
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add this API to restore the status of SPI flash chip to the default
such as addressing mode, whenever detach the driver from device or
reboot the system.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
For Micron spi nor device, when erase/program operation
fails, especially the failure results from intending to
modify protected space, spi-nor upper layers still get
the return which shows the operation succeeds. This is
because current spi_nor_fsr_ready() only uses FSR bit.7
(flag status register) to check device whether ready.
This patch fixes this issue by checking relevant error
bits in FSR.
The FSR is a powerful tool to investigate the status of
device, checking information regarding what the memory is
actually doing and detecting possible error conditions.
Signed-off-by: beanhuo <beanhuo@micron.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
General changes:
* Unconfuse get_unmapped_area and point/unpoint driver methods
* New partition parser: sharpslpart
* Kill GENERIC_IO
* Various fixes
NAND changes:
* Add a flag to mark NANDs that require 3 address cycles to encode a
page address
* Set a default ECC/free layout when NAND_ECC_NONE is requested
* Fix a bug in panic_nand_write()
* Another batch of cleanups for the denali driver
* Fix PM support in the atmel driver
* Remove support for platform data in the omap driver
* Fix subpage write in the omap driver
* Fix irq handling in the mtk driver
* Change link order of mtk_ecc and mtk_nand drivers to speed up boot
time
* Change log level of ECC error messages in the mxc driver
* Patch the pxa3xx driver to support Armada 8k platforms
* Add BAM DMA support to the qcom driver
* Convert gpio-nand to the GPIO desc API
* Fix ECC handling in the mt29f driver
SPI-NOR changes:
* Introduce system power management support
* New mechanism to select the proper .quad_enable() hook by JEDEC ID,
when needed, instead of only by manufacturer ID
* Add support to new memory parts from Gigadevice, Winbond, Macronix and
Everspin
* Maintainance for Cadence, Intel, Mediatek and STM32 drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=wVm7
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20171120' of git://git.infradead.org/linux-mtd
Pull MTD updates from Richard Weinberger:
"General changes:
- Unconfuse get_unmapped_area and point/unpoint driver methods
- New partition parser: sharpslpart
- Kill GENERIC_IO
- Various fixes
NAND changes:
- Add a flag to mark NANDs that require 3 address cycles to encode a
page address
- Set a default ECC/free layout when NAND_ECC_NONE is requested
- Fix a bug in panic_nand_write()
- Another batch of cleanups for the denali driver
- Fix PM support in the atmel driver
- Remove support for platform data in the omap driver
- Fix subpage write in the omap driver
- Fix irq handling in the mtk driver
- Change link order of mtk_ecc and mtk_nand drivers to speed up boot
time
- Change log level of ECC error messages in the mxc driver
- Patch the pxa3xx driver to support Armada 8k platforms
- Add BAM DMA support to the qcom driver
- Convert gpio-nand to the GPIO desc API
- Fix ECC handling in the mt29f driver
SPI-NOR changes:
- Introduce system power management support
- New mechanism to select the proper .quad_enable() hook by JEDEC
ID, when needed, instead of only by manufacturer ID
- Add support to new memory parts from Gigadevice, Winbond, Macronix
and Everspin
- Maintainance for Cadence, Intel, Mediatek and STM32 drivers"
* tag 'for-linus-20171120' of git://git.infradead.org/linux-mtd: (85 commits)
mtd: Avoid probe failures when mtd->dbg.dfs_dir is invalid
mtd: sharpslpart: Add sharpslpart partition parser
mtd: Add sanity checks in mtd_write/read_oob()
mtd: remove the get_unmapped_area method
mtd: implement mtd_get_unmapped_area() using the point method
mtd: chips/map_rom.c: implement point and unpoint methods
mtd: chips/map_ram.c: implement point and unpoint methods
mtd: mtdram: properly handle the phys argument in the point method
mtd: mtdswap: fix spelling mistake: 'TRESHOLD' -> 'THRESHOLD'
mtd: slram: use memremap() instead of ioremap()
kconfig: kill off GENERIC_IO option
mtd: Fix C++ comment in include/linux/mtd/mtd.h
mtd: constify mtd_partition
mtd: plat-ram: Replace manual resource management by devm
mtd: nand: Fix writing mtdoops to nand flash.
mtd: intel-spi: Add Intel Lewisburg PCH SPI super SKU PCI ID
mtd: nand: mtk: fix infinite ECC decode IRQ issue
mtd: spi-nor: Add support for mr25h128
mtd: nand: mtk: change the compile sequence of mtk_nand.o and mtk_ecc.o
mtd: spi-nor: enable 4B opcodes for mx66l51235l
...
It is now unused.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
C++ comments look wrong in kernel tree. Fix one.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
* Add a flag to mark NANDs that require 3 address cycles to encode a
page address
* Set a default ECC/free layout when NAND_ECC_NONE is requested
* Fix a bug in panic_nand_write()
Driver changes:
* Another batch of cleanups for the denali driver
* Fix PM support in the atmel driver
* Remove support for platform data in the omap driver
* Fix subpage write in the omap driver
* Fix irq handling in the mtk driver
* Change link order of mtk_ecc and mtk_nand drivers to speed up boot
time
* Change log level of ECC error messages in the mxc driver
* Patch the pxa3xx driver to support Armada 8k platforms
* Add BAM DMA support to the qcom driver
* Convert gpio-nand to the GPIO desc API
* Fix ECC handling in the mt29f driver
-----BEGIN PGP SIGNATURE-----
iQJABAABCAAqBQJZ+iDfIxxib3Jpcy5icmV6aWxsb25AZnJlZS1lbGVjdHJvbnMu
Y29tAAoJEGXtNgF+CLcAPxoP/iuRGzfzs7DTbS6rLtcbIFKbulj/kjB8BfPtYGC8
1n7C2ZZkQOeargPyf1wtcvNgbVRjUv4/lZ22+HD7l/wDGDjOWeTs0v+it4yGVYzo
iafyx+8m7J4kZWmZnguc6MQnFJ4g0yorUF3tmMYtd+OihgtlB/NWoxEAG40kPuhQ
JpARsV/yWxV+l+30TBVtKCOmcS4tBh7Kjhlmr624BJv6sWilv63PnkG90a1qZUCw
He2PLSNAXXaU7nWta+FKUSzIiRnsWhp2hqf9HIndx4zs1WHK86C15oBXvPuFs3q7
FD5TB/sutTIhmkrqpZZJID/h1QDUkCYd9p2ZO6a0if/S1gZgiBKFFeJXcAlhj0Ze
xqFvE/gni/w2mY8xlqX4/Ras5ndfMuNIIQgyCR/iDwQM4Sv6G5t59nMaCb7r0XYy
Y1pZqVQ/jE8Kh5IkANEmQPVWv95OeQQwY0igtSb5Ih2J9cIzbX/8daE3CP1SOUaX
REOmUJkb1Ad6gA9e3/nS0ZhLttmFtLEgxQqMQ16XWDtKkf+6uQcBPF/1JD6CuFjn
0q6S5p1Mci/IZy2/ds9zIm42/dkG3LSLSG0cd2j60lTgTZsTloIsLcX120bDH/DM
3LejsHgHuaA1Qd7ku9Bn/rfTZdQbSoqQtvkSw3t0touMG/5ErKuleTv9JDaoEb2e
vRGr
=iUhH
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.15' of git://git.infradead.org/l2-mtd
From Boris:
"
Core changes:
* Add a flag to mark NANDs that require 3 address cycles to encode a
page address
* Set a default ECC/free layout when NAND_ECC_NONE is requested
* Fix a bug in panic_nand_write()
Driver changes:
* Another batch of cleanups for the denali driver
* Fix PM support in the atmel driver
* Remove support for platform data in the omap driver
* Fix subpage write in the omap driver
* Fix irq handling in the mtk driver
* Change link order of mtk_ecc and mtk_nand drivers to speed up boot
time
* Change log level of ECC error messages in the mxc driver
* Patch the pxa3xx driver to support Armada 8k platforms
* Add BAM DMA support to the qcom driver
* Convert gpio-nand to the GPIO desc API
* Fix ECC handling in the mt29f driver
"
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch extracts some chunks from spi_nor_init_params and spi_nor_scan()
and moves them into a new spi_nor_init() function.
Indeed, spi_nor_init() regroups all the required SPI flash commands to be
sent to the SPI flash memory before performing any runtime operations
(Fast Read, Page Program, Sector Erase, ...). Hence spi_nor_init():
1) removes the flash protection if applicable for certain vendors.
2) sets the Quad Enable bit, if needed, before using Quad SPI protocols.
3) makes the memory enter its (stateful) 4-byte address mode, if needed,
for SPI flash memory > 128Mbits not supporting the 4-byte address
instruction set.
spi_nor_scan() now ends by calling spi_nor_init() once the probe phase has
completed. Further patches could also use spi_nor_init() to implement the
mtd->_resume() handler for the spi-nor framework.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
There is exactly one board in the kernel that defines platform data
for the GPIO NAND driver.
Use the feature to provide a lookup table for the GPIOs in the board
file so we can convert the driver as a whole to just use GPIO
descriptors.
After this we can cut the use of <linux/of_gpio.h> and use the GPIO
descriptor management from <linux/gpio/consumer.h> alone to grab and use
the GPIOs used in the driver.
I also created a local struct device *dev in the probe() function
because I was getting annoyed with all the &pdev->dev dereferencing.
Cc: arm@kernel.org
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Frans Klaver <fransklaver@gmail.com>
Cc: Gerhard Sittig <gsi@denx.de>
Cc: Jamie Iles <jamie.iles@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Jamie Iles <jamie.iles@oracle.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Several drivers check ->chipsize to see if the third row address cycle
is needed. Instead of embedding magic sizes such as 32MB, 128MB in
drivers, introduce a new flag NAND_ROW_ADDR_3 for clean-up. Since
nand_scan_ident() knows well about the device, it can handle this
properly. The flag is set if the row address bit width is greater
than 16.
Delete comments such as "One more address cycle for ..." because
intention is now clear enough from the code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
* Fix memory leaks in the core
* Remove unused NAND locking support
* Rename nand.h into rawnand.h (preparing support for spi NANDs)
* Use NAND_MAX_ID_LEN where appropriate
* Fix support for 20nm Hynix chips
* Fix support for Samsung and Hynix SLC NANDs
and the following driver changes:
* Various cleanup, improvements and fixes in the qcom driver
* Fixes for bugs detected by various static code analysis tools
* Fix mxc ooblayout definition
* Add a new part_parsers to tmio and sharpsl platform data in order to
define a custom list of partition parsers
* Request the reset line in exclusive mode in the sunxi driver
* Fix a build error in the orion-nand driver when compiled for ARMv4
* Allow 64-bit mvebu platforms to select the PXA3XX driver
-----BEGIN PGP SIGNATURE-----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=bC1+
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.14' of git://git.infradead.org/l2-mtd into mtd/next
From Boris:
"
This pull request contains the following core changes:
* Fix memory leaks in the core
* Remove unused NAND locking support
* Rename nand.h into rawnand.h (preparing support for spi NANDs)
* Use NAND_MAX_ID_LEN where appropriate
* Fix support for 20nm Hynix chips
* Fix support for Samsung and Hynix SLC NANDs
and the following driver changes:
* Various cleanup, improvements and fixes in the qcom driver
* Fixes for bugs detected by various static code analysis tools
* Fix mxc ooblayout definition
* Add a new part_parsers to tmio and sharpsl platform data in order to
define a custom list of partition parsers
* Request the reset line in exclusive mode in the sunxi driver
* Fix a build error in the orion-nand driver when compiled for ARMv4
* Allow 64-bit mvebu platforms to select the PXA3XX driver
"
- add support to the JEDEC JESD216B specification (SFDP tables).
- add support to the Intel Denverton SPI flash controller.
- fix error recovery for Spansion/Cypress SPI NOR memories.
- fix 4-byte address management for the Aspeed SPI controller.
- add support to some Microchip SST26 memory parts
- remove unneeded pinctrl header
-----BEGIN PGP SIGNATURE-----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=A8bR
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-4.14' of git://git.infradead.org/l2-mtd into mtd/next
From Cyrille:
"
This pull request contains the following notable changes:
- add support to the JEDEC JESD216B specification (SFDP tables).
- add support to the Intel Denverton SPI flash controller.
- fix error recovery for Spansion/Cypress SPI NOR memories.
- fix 4-byte address management for the Aspeed SPI controller.
- add support to some Microchip SST26 memory parts
- remove unneeded pinctrl header
"
chip->bits_per_cell which is used to determine the NAND cell type
(SLC/MLC) should always have a value != 0.
Complain loudly if the value is 0 in nand_is_slc() to catch use before
correct initialization.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZo2HiAAoJEHm+PkMAQRiG3OcIAJqSeVK2uQ/QhmqFN1ExYay4
bdTjSTtSk7GH6PxI2C0cqfZvsxOUU7ICDHG8bYM1LA0S0SxfOtoFhHGKc/BcFLX8
MiKJWlF51ZbX0mkIEpKF+C8pRrXPgSqtk3N450/k2BzG9qCZSM93A2NCOB7v9T9w
XOBUIYHqfTS2tdmCinjwu8Ls+w8oPOGH1gLjxZyGnBlg4lTqHMcUufmHeVEAh11d
giGByqqqXH69kGD1HNC7H6quzXN9rz4n0gEwEG0mIhfkJ98b+ESSWwSEXXypOAQD
QT5/6+2YizXf5DPCqR46xasQCPjRsS6Sv0cF2cntW2PEAb4jBjhx5gTFlJcoOC8=
=efWJ
-----END PGP SIGNATURE-----
Merge tag 'v4.13-rc7' into mtd/next
Merge v4.13-rc7 back to resolve merge conflicts in
drivers/mtd/nand/nandsim.c and include/asm-generic/vmlinux.lds.h.
With the introduction of sharpslpart partition parser we can now read the
offsets from NAND: we specify the list of the parsers as platform data, with
cmdlinepart and ofpart parsers first allowing to override the part. table
written in NAND. This is done in the board files using this driver.
Thus, we need to extend sharpsl_nand_platform_data to consider the partition
parsers.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This commit removes hard-coded '8' used for looping into
struct nand_chip.id.data array.
NAND_MAX_ID_LEN has been introduced by Artem Bityutskiy in
53552d22bf for defining ids length in nand_flash_ids[] list.
This commit unifies ids length in nand base driver.
Signed-off-by: Jean-Louis Thekekara <jeanlouis.thekekara@parrot.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
When XIP_KERNEL is enabled, some functions are defined in the .data
ELF section because we require them to be in RAM whenever we communicate
with the flash chip. However this causes problems when FTRACE is
enabled and gcc emits calls to __gnu_mcount_nc in the function
prolog:
drivers/built-in.o: In function `cfi_chip_setup':
:(.data+0x272fc): relocation truncated to fit: R_ARM_CALL against symbol `__gnu_mcount_nc' defined in .text section in arch/arm/kernel/built-in.o
drivers/built-in.o: In function `cfi_probe_chip':
:(.data+0x27de8): relocation truncated to fit: R_ARM_CALL against symbol `__gnu_mcount_nc' defined in .text section in arch/arm/kernel/built-in.o
/tmp/ccY172rP.s: Assembler messages:
/tmp/ccY172rP.s:70: Warning: ignoring changed section attributes for .data
/tmp/ccY172rP.s: Error: 1 warning, treating warnings as errors
make[5]: *** [drivers/mtd/chips/cfi_probe.o] Error 1
/tmp/ccK4rjeO.s: Assembler messages:
/tmp/ccK4rjeO.s:421: Warning: ignoring changed section attributes for .data
/tmp/ccK4rjeO.s: Error: 1 warning, treating warnings as errors
make[5]: *** [drivers/mtd/chips/cfi_util.o] Error 1
/tmp/ccUvhCYR.s: Assembler messages:
/tmp/ccUvhCYR.s:1895: Warning: ignoring changed section attributes for .data
/tmp/ccUvhCYR.s: Error: 1 warning, treating warnings as errors
Specifically, this does not work because the .data section is not
marked executable, which leads LD to not generate trampolines for
long calls.
This moves the __xipram functions into their own .xiptext section instead.
The section is still placed next to .data and located in RAM but is marked
executable, which avoids the build errors.
Also, we only need to place the XIP functions into a separate section
if both CONFIG_XIP_KERNEL and CONFIG_MTD_XIP are set: When only MTD_XIP
is used, the whole kernel is still in RAM and we do not need to worry
about pulling out the rug under it. When only XIP_KERNEL but not MTD_XIP
is set, the kernel is in some form of ROM, but we never write to it.
Note that MTD_XIP has been broken on ARM since around 2011 or 2012. I
have sent another patch[2] to fix compilation, which I plan to merge
through arm-soc unless there are objections. The obvious alternative
to that would be to completely rip out the MTD_XIP support from the
kernel, since obviously nobody has been using it in a long while.
Link: [1] https://patchwork.kernel.org/patch/8109771/
Link: [2] https://patchwork.kernel.org/patch/9855225/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
We are planning to share more code between different NAND based
devices (SPI NAND, OneNAND and raw NANDs), but before doing that
we need to move the existing include/linux/mtd/nand.h file into
include/linux/mtd/rawnand.h so we can later create a nand.h header
containing all common structure and function prototypes.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Peter Pan <peterpandong@micron.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Han Xu <han.xu@nxp.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-By: Harvey Hunt <harveyhuntnexus@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
Commit 7d70f334ad ("mtd: nand: add lock/unlock routines") introduced
support for the Micron LOCK/UNLOCK commands but no one ever used the
nand_lock/unlock() functions.
Remove support for these vendor-specific operations from the core. If
one ever wants to add them back they should be put in nand_micron.c and
mtd->_lock/_unlock should be directly assigned from there instead of
exporting the functions.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
All timings in nand_sdr_timings are expressed in picoseconds but some
of them may not fit in an u32.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: 204e7ecd47 ("mtd: nand: Add a few more timings to nand_sdr_timings")
Reported-by: Alexander Dahl <ada@thorsis.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Alexander Dahl <ada@thorsis.com>
Tested-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
S25FL{128|256|512}S datasheets say:
"When P_ERR or E_ERR bits are set to one, the WIP bit will remain set to
one indicating the device remains busy and unable to receive new operation
commands. A Clear Status Register (CLSR) command must be received to return
the device to standby mode."
Current spi-nor code works until first error occurs, but write/erase errors
are not just rare hardware failures, they also occur if user tries to flash
write-protected areas. After such attempt no SPI command can be executed
any more and even read fails. This patch adds support for P_ERR and E_ERR
bits in Status Register 1 (so that operation fails immediately and not
after a long timeout) and proper recovery from the error condition.
Tested on Spansion S25FS128S, which is supported by S25FL129P entry.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Several MTD devices are using debugfs entries created in the root.
This commit provides the means for a standardized subtree, creating
one "mtd" entry at root, and one entry per device inside it, named
after the device.
The tree is registered in add_mtd_device, and released in
del_mtd_device.
Devices docg3, mtdswap and nandsim were updated to use this subtree
instead of custom ones, and their entries were prefixed with the
drivers' names.
Signed-off-by: Mario J. Rugiero <mrugiero@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch adds support to the JESD216 rev B standard and parses the SFDP
tables to dynamically initialize the 'struct spi_nor_flash_parameter'.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@microchip.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
General updates
* Cleanups and additional flash support for "dataflash" driver
* new driver for mchp23k256 SPI SRAM device
* improve handling of MTDs without eraseblocks (i.e., MTD_NO_ERASE)
* refactor and improve "sub-partition" handling with TRX partition
parser; partitions can now be created as sub-partitions of another
partition
SPI NOR updates, from Cyrille Pitchen and Marek Vasut:
* introduce support to the SPI 1-2-2 and 1-4-4 protocols.
* introduce support to the Double Data Rate (DDR) mode.
* introduce support to the Octo SPI protocols.
* add support to new memory parts for Spansion, Macronix and Winbond.
* add fixes for the Aspeed, STM32 and Cadence QSPI controler drivers.
* clean up the st_spi_fsm driver.
NAND updates, from Boris Brezillon:
* addition of on-die ECC support to Micron driver
* addition of helpers to help drivers choose most appropriate ECC
settings
* deletion of dead-code (cached programming and ->errstat() hook)
* make sure drivers that do not support the SET/GET FEATURES command
return ENOTSUPP use a dummy ->set/get_features implementation
returning -ENOTSUPP (required for Micron on-die ECC)
* change the semantic of ecc->write_page() for drivers setting the
NAND_ECC_CUSTOM_PAGE_ACCESS flag
* support exiting 'GET STATUS' command in default ->cmdfunc()
implementations
* change the prototype of ->setup_data_interface()
A bunch of driver related changes:
* various cleanup, fixes and improvements of the MTK driver
* OMAP DT bindings fixes
* support for ->setup_data_interface() in the fsmc driver
* support for imx7 in the gpmi driver
* finalization of the denali driver rework (thanks to Masahiro for the
work he's done on this driver)
* fix "bitflips in erased pages" handling in the ifc driver
* addition of PM ops and dynamic timing configuration to the atmel
driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ReBr
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20170713' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"General updates:
- Cleanups and additional flash support for "dataflash" driver
- new driver for mchp23k256 SPI SRAM device
- improve handling of MTDs without eraseblocks (i.e., MTD_NO_ERASE)
- refactor and improve "sub-partition" handling with TRX partition
parser; partitions can now be created as sub-partitions of another
partition
SPINOR updates, from Cyrille Pitchen and Marek Vasut:
- introduce support to the SPI 1-2-2 and 1-4-4 protocols.
- introduce support to the Double Data Rate (DDR) mode.
- introduce support to the Octo SPI protocols.
- add support to new memory parts for Spansion, Macronix and Winbond.
- add fixes for the Aspeed, STM32 and Cadence QSPI controler drivers.
- clean up the st_spi_fsm driver.
NAND updates, from Boris Brezillon:
- addition of on-die ECC support to Micron driver
- addition of helpers to help drivers choose most appropriate ECC
settings
- deletion of dead-code (cached programming and ->errstat() hook)
- make sure drivers that do not support the SET/GET FEATURES command
return ENOTSUPP use a dummy ->set/get_features implementation
returning -ENOTSUPP (required for Micron on-die ECC)
- change the semantic of ecc->write_page() for drivers setting the
NAND_ECC_CUSTOM_PAGE_ACCESS flag
- support exiting 'GET STATUS' command in default ->cmdfunc()
implementations
- change the prototype of ->setup_data_interface()
A bunch of driver related changes:
- various cleanup, fixes and improvements of the MTK driver
- OMAP DT bindings fixes
- support for ->setup_data_interface() in the fsmc driver
- support for imx7 in the gpmi driver
- finalization of the denali driver rework (thanks to Masahiro for
the work he's done on this driver)
- fix "bitflips in erased pages" handling in the ifc driver
- addition of PM ops and dynamic timing configuration to the atmel
driver"
* tag 'for-linus-20170713' of git://git.infradead.org/linux-mtd: (118 commits)
Documentation: ABI: mtd: describe "offset" more precisely
mtd: Fix check in mtd_unpoint()
mtd: nand: mtk: release lock on error path
mtd: st_spi_fsm: remove SPINOR_OP_RDSR2 and use SPINOR_OP_RDCR instead
mtd: spi-nor: cqspi: remove duplicate const
mtd: spi-nor: Add support for Spansion S25FL064L
mtd: spi-nor: Add support for mx66u51235f
mtd: nand: mtk: add ->setup_data_interface() hook
mtd: nand: mtk: remove unneeded mtk_ecc_hw_init from mtk_ecc_resume
mtd: nand: mtk: remove unneeded mtk_nfc_hw_init from mtk_nfc_resume
mtd: nand: mtk: disable ecc irq when writing page with hwecc
mtd: nand: mtk: fix incorrect register setting order about ecc irq
mtd: partitions: fixup some allocate_partition() whitespace
mtd: parsers: trx: fix pr_err format for printing offset
MAINTAINERS: Update SPI NOR subsystem git repositories
mtd: extract TRX parser out of bcm47xxpart into a separated module
mtd: partitions: add support for partition parsers
mtd: partitions: add support for subpartitions
mtd: partitions: rename "master" to the "parent" where appropriate
mtd: partitions: remove sysfs files when deleting all master's partitions
...
* addition of on-ecc support to Micron driver
* addition of helpers to help drivers choose most appropriate ECC
settings
* deletion of dead-code (cached programming and ->errstat() hook)
* make sure drivers that do not support the SET/GET FEATURES command
return ENOTSUPP use a dummy ->set/get_features implementation
returning -ENOTSUPP (required for Micron on-die ECC)
* change the semantic of ecc->write_page() for drivers setting the
NAND_ECC_CUSTOM_PAGE_ACCESS flag
* support exiting 'GET STATUS' command in default ->cmdfunc()
implementations
* change the prototype of ->setup_data_interface()
A bunch of driver related changes:
* various cleanup, fixes and improvements of the MTK driver
* OMAP DT bindings fixes
* support for ->setup_data_interface() in the fsmc driver
* support for imx7 in the gpmi driver
* finalization of the denali driver rework (thanks to Masahiro for the
work he's done on this driver)
* fix "bitflips in erased pages" handling in the ifc driver
* addition of PM ops and dynamic timing configuration to the atmel
driver
And as usual we also have a few minor cleanup/fixes/improvements
patches across the subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=INC7
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.13' into MTD
From Boris:
"""
This pull request contains the following core changes:
* addition of on-ecc support to Micron driver
* addition of helpers to help drivers choose most appropriate ECC
settings
* deletion of dead-code (cached programming and ->errstat() hook)
* make sure drivers that do not support the SET/GET FEATURES command
return ENOTSUPP use a dummy ->set/get_features implementation
returning -ENOTSUPP (required for Micron on-die ECC)
* change the semantic of ecc->write_page() for drivers setting the
NAND_ECC_CUSTOM_PAGE_ACCESS flag
* support exiting 'GET STATUS' command in default ->cmdfunc()
implementations
* change the prototype of ->setup_data_interface()
A bunch of driver related changes:
* various cleanup, fixes and improvements of the MTK driver
* OMAP DT bindings fixes
* support for ->setup_data_interface() in the fsmc driver
* support for imx7 in the gpmi driver
* finalization of the denali driver rework (thanks to Masahiro for the
work he's done on this driver)
* fix "bitflips in erased pages" handling in the ifc driver
* addition of PM ops and dynamic timing configuration to the atmel
driver
And as usual we also have a few minor cleanup/fixes/improvements
patches across the subsystem.
"""
- introduce support to the SPI 1-2-2 and 1-4-4 protocols.
- introduce support to the Double Data Rate (DDR) mode.
- introduce support to the Octo SPI protocols.
- add support to new memory parts for Spansion, Macronix and Winbond.
- add fixes for the Aspeed, STM32 and Cadence QSPI controler drivers.
- clean up the st_spi_fsm driver.
-----BEGIN PGP SIGNATURE-----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=ZHnm
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-4.13' into MTD
From Cyrille:
"""
This pull request contains the following notable changes:
- introduce support to the SPI 1-2-2 and 1-4-4 protocols.
- introduce support to the Double Data Rate (DDR) mode.
- introduce support to the Octo SPI protocols.
- add support to new memory parts for Spansion, Macronix and Winbond.
- add fixes for the Aspeed, STM32 and Cadence QSPI controler drivers.
- clean up the st_spi_fsm driver.
"""
Some devices have partitions that are kind of containers with extra
subpartitions / volumes instead of e.g. a simple filesystem data. To
support such cases we need to first create normal flash device
partitions and then take care of these special ones.
It's very common case for home routers. Depending on the vendor there
are formats like TRX, Seama, TP-Link, WRGG & more. All of them are used
to embed few partitions into a single one / single firmware file.
Ideally all vendors would use some well documented / standardized format
like UBI (and some probably start doing so), but there are still
countless devices on the market using these poor vendor specific
formats.
This patch extends MTD subsystem by allowing to specify list of parsers
that should be tried for a given partition. Supporting such poor formats
is highly unlikely to be the top priority so these changes try to
minimize maintenance cost to the minimum. It reuses existing code for
these new parsers and just adds a one property and one new function.
This implementation requires setting partition parsers in a flash
parser. A proper change of bcm47xxpart will follow and in the future we
will hopefully also find a solution for doing it with ofpart
("fixed-partitions").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
struct nand_ecc_caps was designed as flexible as possible to support
multiple stepsizes (like sunxi_nand.c).
So, we need to write multiple arrays even for the simplest case.
I guess many controllers support a single stepsize, so here is a
shorthand macro for the case.
It allows to describe like ...
NAND_ECC_CAPS_SINGLE(denali_pci_ecc_caps, denali_calc_ecc_bytes, 512, 8, 15);
... instead of
static const int denali_pci_ecc_strengths[] = {8, 15};
static const struct nand_ecc_step_info denali_pci_ecc_stepinfo = {
.stepsize = 512,
.strengths = denali_pci_ecc_strengths,
.nstrengths = ARRAY_SIZE(denali_pci_ecc_strengths),
};
static const struct nand_ecc_caps denali_pci_ecc_caps = {
.stepinfos = &denali_pci_ecc_stepinfo,
.nstepinfos = 1,
.calc_ecc_bytes = denali_calc_ecc_bytes,
};
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Driver are responsible for setting up ECC parameters correctly.
Those include:
- Check if ECC parameters specified (usually by DT) are valid
- Meet the chip's ECC requirement
- Maximize ECC strength if NAND_ECC_MAXIMIZE flag is set
The logic can be generalized by factoring out common code.
This commit adds 3 helpers to the NAND framework:
nand_check_ecc_caps - Check if preset step_size and strength are valid
nand_match_ecc_req - Match the chip's requirement
nand_maximize_ecc - Maximize the ECC strength
To use the helpers above, a driver needs to provide:
- Data array of supported ECC step size and strength
- A hook that calculates ECC bytes from the combination of
step_size and strength.
By using those helpers, code duplication among drivers will be
reduced.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The ->errstat() hook is no longer implemented NAND controller drivers.
Get rid of it before someone starts abusing it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Some NAND controllers can assign different NAND timings to different
CS lines. Pass the CS line information to ->setup_data_interface() so
that the NAND controller driver knows which CS line is concerned by
the setup_data_interface() request.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Now that the core NAND subsystem has support for on-die ECC, this commit
brings the necessary code to support on-die ECC on Micron NANDs.
In micron_nand_init(), we detect if the Micron NAND chip supports on-die
ECC mode, by checking a number of conditions:
- It must be an ONFI NAND
- It must be a SLC NAND
- Enabling *and* disabling on-die ECC must work
- The on-die ECC must be correcting 4 bits per 512 bytes of data. Some
Micron NAND chips have an on-die ECC able to correct 8 bits per 512
bytes of data, but they work slightly differently and therefore we
don't support them in this patch.
Then, if the on-die ECC cannot be disabled (some Micron NAND have on-die
ECC forcefully enabled), we bail out, as we don't support such
NANDs. Indeed, the implementation of raw_read()/raw_write() make the
assumption that on-die ECC can be disabled. Support for Micron NANDs
with on-die ECC forcefully enabled can easily be added, but in the
absence of such HW for testing, we preferred to simply bail out.
If the on-die ECC is supported, and requested in the Device Tree, then
it is indeed enabled, by using custom implementations of the
->read_page(), ->read_page_raw(), ->write_page() and ->write_page_raw()
operation to properly handle the on-die ECC.
In the non-raw functions, we need to enable the internal ECC engine
before issuing the NAND_CMD_READ0 or NAND_CMD_SEQIN commands, which is
why we set the NAND_ECC_CUSTOM_PAGE_ACCESS option at initialization
time (it asks the NAND core to let the NAND driver issue those
commands).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
A lot of drivers are providing their own ->cmdfunc(), and most of the
time this implementation does not support all possible NAND operations.
But since ->cmdfunc() cannot return an error code, the core has no way
to know that the operation it requested is not supported.
This is a problem we cannot address for all kind of operations with the
current design, but we can prevent these silent failures for the
GET/SET FEATURES operation by overloading the default
->onfi_{set,get}_features() methods with one returning -ENOTSUPP.
Reported-by: Chris Packham <Chris.Packham@alliedtelesis.co.nz>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Chris Packham <Chris.Packham@alliedtelesis.co.nz>
Mauro says:
This patch series convert the remaining DocBooks to ReST.
The first version was originally
send as 3 patch series:
[PATCH 00/36] Convert DocBook documents to ReST
[PATCH 0/5] Convert more books to ReST
[PATCH 00/13] Get rid of DocBook
The lsm book was added as if it were a text file under
Documentation. The plan is to merge it with another file
under Documentation/security, after both this series and
a security Documentation patch series gets merged.
It also adjusts some Sphinx-pedantic errors/warnings on
some kernel-doc markups.
I also added some patches here to add PDF output for all
existing ReST books.
This patch starts adding support to Octo SPI protocols (SPI x-y-8).
Op codes for Fast Read and/or Page Program operations using Octo SPI
protocols are not known yet (no JEDEC specification has defined them yet)
but we'd rather introduce the Octo SPI protocols now so it's done as it
should be.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
This patch introduces support to Double Transfer Rate (DTR) SPI protocols.
DTR is used only for Fast Read operations.
According to manufacturer datasheets, whatever the number of I/O lines
used during instruction (x) and address/mode/dummy (y) clock cycles, DTR
is used only during data (z) clock cycles of SPI x-y-z protocols.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
This patch changes the prototype of spi_nor_scan(): its 3rd parameter
is replaced by a 'struct spi_nor_hwcaps' pointer, which tells the spi-nor
framework about the actual hardware capabilities supported by the SPI
controller and its driver.
Besides, this patch also introduces a new 'struct spi_nor_flash_parameter'
telling the spi-nor framework about the hardware capabilities supported by
the SPI flash memory and the associated settings required to use those
hardware caps.
Then, to improve the readability of spi_nor_scan(), the discovery of the
memory settings and the memory initialization are now split into two
dedicated functions.
1 - spi_nor_init_params()
The spi_nor_init_params() function is responsible for initializing the
'struct spi_nor_flash_parameter'. Currently this structure is filled with
legacy values but further patches will allow to override some parameter
values dynamically, for instance by reading the JESD216 Serial Flash
Discoverable Parameter (SFDP) tables from the SPI memory.
The spi_nor_init_params() function only deals with the hardware
capabilities of the SPI flash memory: especially it doesn't care about
the hardware capabilities supported by the SPI controller.
2 - spi_nor_setup()
The second function is called once the 'struct spi_nor_flash_parameter'
has been initialized by spi_nor_init_params().
With both 'struct spi_nor_flash_parameter' and 'struct spi_nor_hwcaps',
the new argument of spi_nor_scan(), spi_nor_setup() computes the best
match between hardware caps supported by both the (Q)SPI memory and
controller hence selecting the relevant settings for (Fast) Read and Page
Program operations.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
The nand_read_page_raw() and nand_write_page_raw() functions might be
re-used by vendor-specific implementations of the read_page/write_page
functions. Instead of having vendor-specific code duplicate this code,
it is much better to export those functions and allow them to be
re-used.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
A number of NAND flashes have a capability called "on-die ECC" where the
NAND chip itself is capable of detecting and correcting errors.
Linux already has support for using the ECC implementation of the NAND
controller, or a software based ECC implementation, but not for using
the ECC implementation of the NAND controller. However, such an
implementation is sometimes useful in situations where the NAND
controller provides ECC algorithms that are not strong enough for the
NAND chip used on the system. A typical case is a NAND chip that
requires a 4-bit ECC, while the NAND controller only provides a 1-bit
ECC algorithm.
This commit introduces the support for the NAND_ECC_ON_DIE ECC mode:
- Parsing of the "on-die" value for the "nand-ecc-mode" Device Tree
property
- Handling NAND_ECC_ON_DIE case in nand_scan_tail(). The idea is that
the vendor specific code for the NAND chip must implement
->read_page() and ->write_page(). It may optionally provide its own
->read_page_raw() and ->write_page_raw() as well. For OOB operation,
we assume the standard operations are good enough, but they can be
overridden by the vendor specific code if needed.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
NAND, from Boris:
"""
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
"""
SPI NOR, from Cyrille:
"""
- fixes in the hisi SPI controller driver.
- fixes in the intel SPI controller driver.
- fixes in the Mediatek SPI controller driver.
- fixes to some SPI flash memories not supported the Chip Erase command.
- add support to some new memory parts (Winbond, Macronix, Micron, ESMT).
- add new driver for the STM32 QSPI controller.
"""
And a few fixes for Gemini and Versatile platforms on physmap-of
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dxj5
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20170510' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"NAND, from Boris:
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
SPI NOR, from Cyrille:
- fixes in the hisi, intel and Mediatek SPI controller drivers
- fixes to some SPI flash memories not supporting the Chip Erase
command.
- add support to some new memory parts (Winbond, Macronix, Micron,
ESMT).
- add new driver for the STM32 QSPI controller
And a few fixes for Gemini and Versatile platforms on physmap-of"
* tag 'for-linus-20170510' of git://git.infradead.org/linux-mtd: (100 commits)
MAINTAINERS: Update NAND subsystem git repositories
mtd: nand: gpio: update binding
mtd: nand: add ooblayout for old hamming layout
mtd: oxnas_nand: Allocating more than necessary in probe()
dt-bindings: mtd: Document the STM32 QSPI bindings
mtd: mtk-nor: set controller's address width according to nor flash
mtd: spi-nor: add driver for STM32 quad spi flash controller
mtd: nand: brcmnand: Check flash #WP pin status before nand erase/program
mtd: nand: davinci: add comment on NAND subpage write status on keystone
mtd: nand: omap2: Fix partition creation via cmdline mtdparts
mtd: nand: NULL terminate a of_device_id table
mtd: nand: Fix a couple error codes
mtd: nand: allow drivers to request minimum alignment for passed buffer
mtd: nand: allocate aligned buffers if NAND_OWN_BUFFERS is unset
mtd: nand: denali: allow to override revision number
mtd: nand: denali_dt: use pdev instead of ofdev for platform_device
mtd: nand: denali_dt: remove dma-mask DT property
mtd: nand: denali: support 64bit capable DMA engine
mtd: nand: denali_dt: enable HW_ECC_FIXUP for Altera SOCFPGA variant
mtd: nand: denali: support HW_ECC_FIXUP capability
...
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4jGH
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.12' of github.com:linux-nand/linux into MTD
From Boris:
"""
This pull request contains:
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
"""
In some cases, nand_do_{read,write}_ops is passed with unaligned
ops->datbuf. Drivers using DMA will be unhappy about unaligned
buffer.
The new struct member, buf_align, represents the minimum alignment
the driver require for the buffer. If the buffer passed from the
upper MTD layer does not have enough alignment, nand_do_*_ops will
use bufpoi.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The comment for ecc.read_page() requires that it should return
"0 if bitflips uncorrectable".
Actually, drivers could return positive values when uncorrectable
bitflips occur. For example, nand_read_page_swecc() is the case.
If ecc.correct() returns -EBADMSG for the first ECC sector, and
a positive value for the second one, nand_read_page_swecc() returns
a positive max_bitflips and increments ecc_stats.failed for the same
page.
The requirement can be relaxed by tweaking nand_do_read_ops().
Move the max_bitflips calculation below the retry.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The last/only user of the chip->write_page() hook (the Atmel NAND
controller driver) has been reworked and is no longer specifying a custom
->write_page() implementation.
Drop this hook before someone else start abusing it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
MTD already allocates backing_dev_info dynamically. Convert it to use
generic infrastructure for this including proper refcounting. We drop
mtd->backing_dev_info as its only use was to pass mtd_bdi pointer from
one file into another and if we wanted to keep that in a clean way, we'd
have to make mtd hold and drop bdi reference as needed which seems
pointless for passing one global pointer...
CC: David Woodhouse <dwmw2@infradead.org>
CC: Brian Norris <computersforpeace@gmail.com>
CC: linux-mtd@lists.infradead.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
This allows better compile-time optimizations with CONFIG_OF disabled.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Move Macronix specific initialization logic into nand_macronix.c. This
is part of the "separate vendor specific code from core" cleanup
process.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Move AMD/Spansion specific initialization/detection logic into
nand_amd.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
Move Micron specific initialization logic into nand_micron.c. This is
part of the "separate vendor specific code from core" cleanup process.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
Move Toshiba specific initialization and detection logic into
nand_toshiba.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
Move Hynix specific initialization and detection logic into
nand_hynix.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
Move Samsung specific initialization and detection logic into
nand_samsung.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
A lot of NANDs are implementing generic features in a non-generic way,
or are providing advanced auto-detection logic where the NAND ID bytes
meaning changes with the NAND generation.
Providing this vendor specific initialization step will allow us to get
rid of full-id entries in the nand_ids table or all the vendor specific
cases added over the time in the generic NAND ID decoding logic.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
There is no reason to expose the NAND manufacturer table. Provide an
helper function to find manufacturers by their id.
We also turn the nand_manufacturers table into a const array, since its
members are not modified after the initial assignment.
Finally, we remove the sentinel manufacturer entry from the manufacturers
table (we already have the array size information given by ARRAY_SIZE()),
and add the nand_manufacturer_name() helper to handle the "Unknown" case
properly.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Drop the 's' at the end of nand_manufacturers since the struct is actually
describing a single manufacturer, not a manufacturer table.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Store the NAND ID in struct nand_chip to avoid passing id_data and id_len
as function parameters.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Fix typos and add the following to the scripts/spelling.txt:
partiton||partition
Link: http://lkml.kernel.org/r/1481573103-11329-7-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This can be used to easily identify a specific chip on a system with
multiple chips.
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
- add support to the 4-byte address instruction set.
- add support to new memory parts.
- add support to S3AN memories.
- add support to the Intel SPI controller.
- add support to the Aspeed AST2400 and AST2550 controllers.
- fix max SPI transfer and message sizes in m25p80_read().
- fix the Candence QSPI driver.
- fix the Freescale QSPI driver.
-----BEGIN PGP SIGNATURE-----
iQI4BAABCAAiBQJYncJ7GxxjeXJpbGxlLnBpdGNoZW5Ad2VkZXY0dS5mcgAKCRDn
4OgLHRpJcswfD/0dvIvhI9R9ne/kHUsXbW2tIAIc2vrl/jiEA0O90rinRRjxLyIi
3EacSYpL8PXAh5diNannIw/DrjK0FiHB34jJ1NwMP7CQbYMbfb1SGwp5nmIP676W
4iEaSOJDQu76Vbe5L2O4xHUIJoO1l9cr/bZDPXRachBD8H48ZRZUTx0ujff4LbiG
lEwv1Bk35doTRHgmPErPIB/WOlYdvLaoiCUVe9ME0mEEzCmEjoZorTDwaSBpBAMB
4Z04Lz06iP1aPFUm2VYvK5xMvkFN4tS+6xzWpUOUYj8Tty1YptYI7mQINa69J2NA
O8A/elH39Yv1FYvWgrC2SIS/kbHTR/Bxz6napJ0hK3HasLFCwt7Eq2w/XBxr/Wn9
+02buij0PWKywJfuj7tOiAId5IJW0hhEit2BcBFihwsiDDxix679beQoCZ/WRuW/
kJmR+NLRNByVyKCOP239VobiYWjy8DhDTpH5XGwI7bPTiJuS6G6MCVH3f0tYnFTo
8J3gXp4SH2mw6YzWrL8YtKzFKcLEfXTOGc/GFGQX2URV5Es1/Lw4Nh5lrkbEbVoy
dc/S57Ftdde/56L4lDDbydn7pAU8FbuX2gSewvJRuFyhCBKSyw2JEoy27T7t50pd
hN1JvuNYGQ5HP0Vqa/oe1g1GHnBfxiIOm5THX+Iv+3Y0jM1iUDeVeO4DTQ==
=/fPM
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-4.11-v2' of git://github.com/spi-nor/linux
From Cyrille:
"""
This pull request contains the following notable changes:
- add support to the 4-byte address instruction set.
- add support to new memory parts.
- add support to S3AN memories.
- add support to the Intel SPI controller.
- add support to the Aspeed AST2400 and AST2550 controllers.
- fix max SPI transfer and message sizes in m25p80_read().
- fix the Candence QSPI driver.
- fix the Freescale QSPI driver.
"""
This patch renames the SPINOR_OP_* macros of the 4-byte address
instruction set so the new names all share a common pattern: the 4-byte
address name is built from the 3-byte address name appending the "_4B"
suffix.
The patch also introduces new op codes to support other SPI protocols such
as SPI 1-4-4 and SPI 1-2-2.
This is a transitional patch and will help a later patch of spi-nor.c
to automate the translation from the 3-byte address op codes into their
4-byte address version.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Xilinx Spartan-3AN FPGAs contain an In-System Flash where they keep
their configuration data and (optionally) some user data.
The protocol of this flash follows most of the spi-nor standard. With
the following differences:
- Page size might not be a power of two.
- The address calculation (default addressing mode).
- The spi nor commands used.
Protocol is described on Xilinx User Guide UG333
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
The user visible change here is that mtd partitions get an of_node link
in sysfs.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The fields max_bb_per_die and blocks_per_die are useful determining the
number of bad blocks a MTD needs to allocate. How they are set will
depend on if the chip is ONFI, JEDEC or a full-id entry in the nand_ids
table.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electron.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If implemented, 'max_bad_blocks' returns the maximum number of bad
blocks to reserve for a MTD. An implementation for NAND is coming soon.
Signed-off-by: Jeff Westfahl <jeff.westfahl@ni.com>
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electron.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The FSMC driver has an execution path and a header file in
<linux/mtd/fsmc.h> that serves to support passing in platform
data through board files, albeit no upstream users of this
mechanism exist.
The header file also contains function headers for functions that
do not exist in the kernel.
Delete this and move the platform data struct, parsing and
handling into the driver, assume we are using OF and make the
driver depend on OF, remove the ifdefs making that optional.
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fix kernel-doc warnings in <linux/mtd/nand.h>:
..//include/linux/mtd/nand.h:658: warning: No description found for parameter 'tCEH_min'
..//include/linux/mtd/nand.h:877: warning: No description found for parameter 'data_interface'
Fixes: eee64b700e ("mtd: nand: Introduce nand_data_interface")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
- new tango NAND controller driver
- new ox820 NAND controller driver
- addition of a new full-ID entry in the nand_ids table
- rework of the s3c240 driver to support DT
- extension of the nand_sdr_timings to expose tCCS, tPROG and tR
- addition of a new flag to ask the core to wait for tCCS when sending
a RNDIN/RNDOUT command
- addition of a new flag to ask the core to let the controller driver
send the READ/PROGPAGE command
This pull request also contains minor fixes/cleanup/cosmetic changes:
- properly support 512 ECC step size in the sunxi driver
- improve the error messages in the pxa probe path
- fix module autoload in the omap2 driver
- cleanup of several nand drivers to return nand_scan{_tail}() error
code instead of returning -EIO
- various cleanups in the denali driver
- cleanups in the ooblayout handling (MTD core)
- fix an error check in nandsim
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=og/Y
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.10' of github.com:linux-nand/linux
From Boris Brezillon:
"""
This pull request contains the following notable changes:
- new tango NAND controller driver
- new ox820 NAND controller driver
- addition of a new full-ID entry in the nand_ids table
- rework of the s3c240 driver to support DT
- extension of the nand_sdr_timings to expose tCCS, tPROG and tR
- addition of a new flag to ask the core to wait for tCCS when sending
a RNDIN/RNDOUT command
- addition of a new flag to ask the core to let the controller driver
send the READ/PROGPAGE command
This pull request also contains minor fixes/cleanup/cosmetic changes:
- properly support 512 ECC step size in the sunxi driver
- improve the error messages in the pxa probe path
- fix module autoload in the omap2 driver
- cleanup of several nand drivers to return nand_scan{_tail}() error
code instead of returning -EIO
- various cleanups in the denali driver
- cleanups in the ooblayout handling (MTD core)
- fix an error check in nandsim
"""
If your controller already sends the required NAND commands when
reading or writing a page, then the framework is not supposed to
send READ0 and SEQIN/PAGEPROG respectively.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Drivers implementing ->cmd_ctrl() and relying on the default ->cmdfunc()
implementation usually don't wait tCCS when a column change (RNDIN or
RNDOUT) is requested.
Add an option flag to ask the core to do so (note that we keep this as
an opt-in to avoid breaking existing implementations), and make use of
the ->data_interface information is available (otherwise, wait 500ns).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Add the tR_max, tBERS_max, tPROG_max and tCCS_min timings to the
nand_sdr_timings struct.
Assign default/safe values for the statically defined timings, and
extract them from the ONFI parameter table if the NAND is ONFI
compliant.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
When changing from one data interface setting to another, one has to
ensure a specific sequence which is described in the ONFI spec.
One of these constraints is that the CE line has go high after a reset
before a command can be sent with the new data interface setting, which
is not guaranteed by the current implementation.
Rework the nand_reset() function and all the call sites to make sure the
CE line is asserted and released when required.
Also make sure to actually apply the new data interface setting on the
first die.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: d8e725dd83 ("mtd: nand: automate NAND timings selection")
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Kamal Dasu