Adding "ethtool -d" support. Due to the complexity of the FW and HW, there are a
lot of different regions in the chip - to keep the code as clean as possible,
the ranges were put in an H file. Some areas cannot be read if the driver is
running - so by default, the driver will not access those areas - but any
programmer facing a problem will be able to easily manipulate the driver to
extract full dump. The full dump can also be used with kernel dump modules in
case of kernel panic.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the FP index to relevant debug prints and simply beautify some others
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On unload, the FW assumes that no packets will be sent after the driver sends
the FW stop command. To ensure that, the driver must always call
netif_tx_disable
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using DMA engine (DMAE) to initialize large consecutive memories in the chip
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the napi_poll budget only when updating it. Also add a comment to explain
the rmb
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx interrupt is very short and there is no need to limit it to a budget
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rmb to read status block indices on load
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the comment explains, this smb_mb is needed only if the queue is stopped
(which is unlikely) so the barrier can be moved to that location
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted by Ben Hutchings <bhutchings@solarflare.com>, these smb_mb are not
needed
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whitespaces, empty lines, 80 columns, indentations and removing redundant
parenthesis
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-arrange the driver debug print to support the Tx multi-queue and add support
for debug prints at the end of the ring (when start<end)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resolving the majority of the issues, but there are still some left for future
patches.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When loading in diag mode, set the device to loopback instead of normal link and
then changing it to loopback mode
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver default WoL setting is set to the nvram default value
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling many debug prints, it can take a while before processing an event.
To ease the debug process, allow bigger timeout before giving up
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows better debug capabilities if the user wants to force an MRRS value
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supporting non-default pre-emphasis settings for the internal and some external
PHYs
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some dual port PHY require HW lock since they are used by both interfaces
(different driver instances). Since this list is getting longer, update a
parameter at load time instead of calculating it on runtime
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also adding the ability to recognize the optic module and disable it if it is
not authorized for safety reasons - since this feature might upset some users
which are willing to take the risk, it is optional and can be disabled by
setting an nvram bit (or a trivial driver patch to set this bit).
This dual port PHY requires special handling if the ports are swapped.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A GPIO is used with the 8726 PHY. Adding the GPIO related functions in this
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are too many different board types and this field is not scalable.
Removing it and making decisions according to other fields
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting better HW thresholds and enabling FW capabilities for better
enforcement. Also set the HW to more efficiently use the internal buffers if
this is a single port design
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the configuration can be set when loading the device and shouldn't be
re-calculated after each link up indication since it is not dependent on the
link speed
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Should be called for all incoming packets and not just for GRO packets
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-ordering the statistics to enhance readability and adding per queue
statistics (available via ethtool -S)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This check is unreliable since latest MC can issue warnings on rare occasions
which are not fatal errors
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before initializing the chip after iSCSI boot, the interrupts of the function
that was used to boot must be disabled. That means that the driver needs to set
the chip as if it is the iSCSI PCI function - this bug is exposed only with MSI
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling MSI on top of MSI-X and INTA. Also changing the module parameter to
allow choosing INTA or MSI even when MSI-X is available. The default status
block should not be reversed for endianity. Since MSI can issue
re-configuration, the interrupt disable function now requires mmiowb
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding Tx multi-queue and enabling multi-queue by default
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the FW blob and the relevant definitions without any logic. It
also contains the minimal mandatory code changes to work with this FW
but it does not contain enabling of the new features that this FW
provides.
This FW is needed for:
- More efficient multi-queue
- per queue statistics
- Big-endian issue with MSI
- Improved pause response
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current tx_has_work waited until all packets sent by the driver
are marked as completed by the FW. This is too greedy and it causes
the bnx2x_poll to spin in vain. The driver should only check that all
packets FW already completed are freed - only in unload flow the
driver should make sure that transmit queue is empty
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A link change interrupt might be queued and activated after the loopback was set
and it will cause the loopback to fail. The PHY lock should be kept until the
loopback test is over.
That implies that the bnx2x_test_link should used within the loopback function
and not bnx2x_wait_for_link since that function also takes the PHY link
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Waiting for the FW to response requires a memory barrier
Signed-off-by: Michal Kalderon <michals@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rmmod might hang without this patch since the reference counter is not going
down
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein