Enhance stm32-exti driver to support STM32MP13 SoC. This SoC uses the same
hardware version than STM32MP15. Only EXTI line mapping is changed and
following EXTI lines are supported: GPIO, RTC, I2C[1-5], UxART[1-8],
USBH_EHCI, USBH_OHCI, USB_OTG, LPTIM[1-5], ETH[1-2].
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220202140005.860-3-alexandre.torgue@foss.st.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210908105715.1780-1-caihuoqing@baidu.com
Wherever possible, replace constructs that match either
generic_handle_irq(irq_find_mapping()) or
generic_handle_irq(irq_linear_revmap()) to a single call to
generic_handle_domain_irq().
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
When devm_ioremap_resource() fails, a clear enough error message will be
printed by its subfunction __devm_ioremap_resource(). The error
information contains the device name, failure cause, and possibly resource
information.
Therefore, remove the error printing here to simplify code and reduce the
binary size.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210511125428.6108-2-thunder.leizhen@huawei.com
Add following usart instances exti direct event support (used for UART wake
up).
- exti 26 (USART1) is mapped to GIC 37
- exti 27 (USART2) is mapped to GIC 38
- exti 28 (USART3) is mapped to GIC 39
- exti 29 (USART6) is mapped to GIC 71
- exti 31 (UART5) is mapped to GIC 53
- exti 32 (UART7) is mapped to GIC 82
- exti 33 (UART8) is mapped to GIC 83
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210319184253.5841-4-erwan.leray@foss.st.com
In the current code, when the eoi callback of the exti clears the pending
bit of the current interrupt, it will first read the values of fpr and
rpr, then logically OR the corresponding bit of the interrupt number,
and finally write back to fpr and rpr.
We found through experiments that if two exti interrupts,
we call them int1/int2, arrive almost at the same time. in our scenario,
the time difference is 30 microseconds, assuming int1 is triggered first.
there will be an extreme scenario: both int's pending bit are set to 1,
the irq handle of int1 is executed first, and eoi handle is then executed,
at this moment, all pending bits are cleared, but the int 2 has not
finally been reported to the cpu yet, which eventually lost int2.
According to stm32's TRM description about rpr and fpr: Writing a 1 to this
bit will trigger a rising edge event on event x, Writing 0 has no
effect.
Therefore, when clearing the pending bit, we only need to clear the
pending bit of the irq.
Fixes: 927abfc446 ("irqchip/stm32: Add stm32mp1 support with hierarchy domain")
Signed-off-by: qiuguorui1 <qiuguorui1@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org # v4.18+
Link: https://lore.kernel.org/r/20200820031629.15582-1-qiuguorui1@huawei.com
EXTI lines are mainly used to wake-up system from CStop low power mode.
Currently, if a device wants to use a EXTI (direct) line as wakeup line,
it has to declare 2 interrupts:
- one for EXTI used to wake-up system (with dedicated_wake_irq api).
- one for GIC used to get the wake up reason inside the concerned IP.
This split is not really needed as each EXTI line is actually "linked " to
a GIC. So to avoid this useless double interrupt management in each
wake-up driver, this patch lets the STM32 EXTI driver abstract it by
mapping each EXTI line to his corresponding GIC.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200717140717.29606-1-alexandre.torgue@st.com
Now that the hwspin_lock_timeout_in_atomic() API is available use it.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200706081115.25180-1-alexandre.torgue@st.com
This commit introduces retrigger support for stm32_ext_h chip.
It consists to rise the GIC interrupt mapped to an EXTI line.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20200219143229.18084-2-alexandre.torgue@st.com
This irqchip driver uses the hwspinlock framework (coprocessor HW regs
access concurrency) for the stm32mp1-exti device.
Hence, this driver needs to handle the hwspinlock driver dependency
using the deferred probe mechanism which requires to move this driver
into a platform one with a probe() ops.
This applies only for the device which is "st,stm32mp1-exti" compatible,
the management of the other devices (st,stm32h7-exti / st,stm32-exti) is
kept unchanged (use IRQCHIP_DECLARE)
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The rising configuration status register (rtsr) is not banked.
As it is shared with the co-processor, it should not be written at probe
time, else the co-processor configuration will be lost.
Fixes: f9fc174550 ("irqchip/stm32: Add host and driver data structures")
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Falling and rising configuration and status registers are not banked.
As they are shared with M4 co-processor, they should not be cleared
at probe time, else M4 co-processor configuration will be lost.
Fixes: f9fc174550 ("irqchip/stm32: Add host and driver data structures")
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Domain translate function is needed to recover irq
configuration parameters from DT node
Fixes: 927abfc446 ("irqchip/stm32: Add stm32mp1 support with hierarchy domain")
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If a hwspinlock is defined in device tree use it to protect
configuration registers.
Do not request for hwspinlock during the exti driver init since the
hwspinlock driver is not probed yet at that stage and the exti driver
does not support deferred probe.
Instead of this, postpone the hwspinlock request at the first time the
hwspinlock is actually needed.
Use the hwspin_trylock_raw() API which is the most appropriated here
Indeed:
- hwspin_lock_() calls are under spin_lock protection (chip_data->rlock
or gc->lock).
- the _timeout() API relies on jiffies count which won't work if IRQs
are disabled which is the case here (a large part of the IRQ setup is
done atomically (see irq/manage.c))
As a consequence implement the retry/timeout lock from here. And since
all of this is done atomically, reduce the timeout delay to 1 ms.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If there are any errors in stm32_exti_host_init() then it leads to a
NULL dereference in the callers. The function should clean up after
itself.
Fixes: f9fc174550 ("irqchip/stm32: Add host and driver data structures")
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch fixes a datasheet issue, in the draft version the "exti0"
was not connected whereas is it.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
A CONFIG_SMP=n build emits a harmless compile-time warning:
drivers/irqchip/irq-stm32-exti.c:495:12: error: 'stm32_exti_h_set_affinity' defined but not used [-Werror=unused-function]
The #ifdef is inconsistent here, and it's better to use an IS_ENABLED() check
that lets the compiler silently drop that function.
Fixes: 927abfc446 ("irqchip/stm32: Add stm32mp1 support with hierarchy domain")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Radoslaw Pietrzyk <radoslaw.pietrzyk@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Link: https://lkml.kernel.org/r/20180605114347.1347128-1-arnd@arndb.de
This patch adds suspend/resume feature for exti hierarchy domain.
-suspend function sets wake_active into imr of each banks
-resume function restores the mask_cache interrupt into
imr of each banks
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Exti controller has been differently integrated on stm32mp1 SoC.
A parent irq has only one external interrupt. A hierachy domain could
be used. Handlers are call by parent, each parent interrupt could be
masked and unmasked according to the needs.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch prepares functions which could be reused by
next variant of stm32 exti controller.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch adds host and driver data structures to support
different stm32 exti controllers with variants.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch adds suspend feature.
-Use default irq_set_wake function to store wakeup request.
-Suspend function set wake_active into imr of each bank
and save rising/falling trigger registers.
-Resume function restore the mask_cache interrupt into
imr of each bank and restore rising/falling trigger registers.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch adds support of rising/falling pending registers.
Falling pending register (fpr) is needed for next revision.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
-WARNING: struct irq_domain_ops should normally be const
-CHECK: Alignment should match open parenthesis
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
- In stm32_exti_alloc function, discards irq_domain_set_info
with handle_simple_irq. This overwrite the setting defined while init
of generic chips. Exti controller manages edge irq type.
- Removes acking in chained irq handler as this is done by
irq_chip itself inside handle_edge_irq
- removes unneeded irq_domain_ops.xlate callback
Acked-by: Ludovic Barre <ludovic.barre@st.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Radoslaw Pietrzyk <radoslaw.pietrzyk@gmail.com>
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Move irq_set_wake on interrupt mask, needed to wake up from
low power mode as the event mask is not able to do so.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
-After cold boot, imr default value depends on hardware configuration.
-After hot reboot the registers must be cleared to avoid residue.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
stm32h7 has up to 96 inputs
(3 banks of 32 inputs max).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
-Prepare to manage multi-bank of external interrupts
(N banks of 32 inputs).
-Prepare to manage registers offsets by compatible
(registers offsets could be different follow per stm32 platform).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Lee Jones <lee@kernel.org>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-tegra@vger.kernel.org
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The STM32 external interrupt controller consists of edge detectors that
generate interrupts requests or wake-up events.
Each line can be independently configured as interrupt or wake-up source,
and triggers either on rising, falling or both edges. Each line can also
be masked independently.
Originally-from: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: arnd@arndb.de
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: bruherrera@gmail.com
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: lee.jones@linaro.org
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1474387259-18926-3-git-send-email-alexandre.torgue@st.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Alexandre Torgue