If SMP fails we should not leave any keys (LTKs or IRKs) hanging around
the internal lists. This patch adds the necessary code to
smp_chan_destroy to remove any keys we may have in case of pairing
failure.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The random numbers in Bluetooth Low Energy are 64-bit numbers and should
also be little endian since the HCI specification is little endian.
Change the whole Low Energy pairing to use __le64 instead of a byte
array.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If some of the cleanup commands caused by mgmt_set_powered(off) never
complete we should still force the adapter to be powered down. This is
rather easy to do since hdev->power_off is already a delayed work
struct. This patch schedules this delayed work if at least one HCI
command was sent by the cleanup procedure.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When powering off and disconnecting devices we should also consider
connections which have not yet reached the BT_CONNECTED state. They may
not have a valid handle yet and simply sending a HCI_Disconnect will not
work.
This patch updates the code to either disconnect, cancel connection
creation or reject incoming connection creation based on the current
conn->state value as well as the link type in question.
When the power off procedure results in canceling connection attempts
instead of disconnecting connections we get a connection failed event
instead of a disconnection event. Therefore, we also need to have extra
code in the mgmt_connect_failed function to check if we should proceed
with the power off or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the LE white list gets changed via HCI commands make sure that
the internal storage of the white list entries gets updated.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The current LE white list entries require storing in the HCI controller
structure. So provide a storage and access functions for it. In addition
export the current list via debugfs.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When starting up a controller make sure that all LE white list entries
are cleared. Normally the HCI Reset takes care of this. This is just
in case no HCI Reset has been executed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hci_blacklist_clear function is not used outside of hci_core.c and
can be made static.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The number of places needing the local Identity Address are starting to
grow so it's better to have a single place for the logic of determining
it. This patch adds a convenience function for getting the Identity
Address and updates the two current places needing this to use it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To know the real source address for incoming connections (needed e.g.
for SMP) we should store the own_address_type parameter that was used
for the last HCI_LE_Write_Advertising_Parameters command. This patch
adds a proper command complete handler for the command and stores the
address type in a new adv_addr_type variable in the hci_dev struct.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to mgmt-api.txt, in case of confirm name command,
cmd_complete should be always use as a response. Not command status
as it is now for failures.
Using command complete on failure is actually better as client might
be interested in device address for which confirm name failed.
Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If new scanning parameters are set while background scan is running,
we should restart background scanning so these parameters are updated.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patches creates the public hci_req_add_le_passive_scan helper so
it can be re-used outside hci_core.c in the next patch.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds to debugfs the le_auto_conn file. This file will be
used to test LE auto connection infrastructure.
This file accept writes in the following format:
"add <address> <address_type> [auto_connect]"
"del <address> <address_type>"
"clr"
The <address type> values are:
* 0 for public address
* 1 for random address
The [auto_connect] values are (for more details see struct hci_
conn_params):
* 0 for disabled (default)
* 1 for always
* 2 for link loss
So for instance, if you want the kernel autonomously establishes
connections with device AA:BB:CC:DD:EE:FF (public address) every
time the device enters in connectable mode (starts advertising),
you should run the command:
$ echo "add AA:BB:CC:DD:EE:FF 0 1" > /sys/kernel/debug/bluetooth/hci0/le_auto_conn
To delete the connection parameters for that device, run the command:
$ echo "del AA:BB:CC:DD:EE:FF 0" > /sys/kernel/debug/bluetooth/hci0/le_auto_conn
To clear the connection parameters list, run the command:
$ echo "clr" > /sys/kernel/debug/bluetooth/hci0/le_auto_conn
Finally. to get the list of connection parameters configured in kernel,
read the le_auto_conn file:
$ cat /sys/kernel/debug/bluetooth/hci0/le_auto_conn
This file is created only if LE is enabled.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Only identity addresses are inserted into hdev->pend_le_conns. So,
in order to support resolvable private addresses in auto connection
mechanism, we should resolve the address before checking for pending
connections.
Thus, this patch adds an extra check in check_pending_le_conn() and
updates 'addr' and 'addr_type' variables before hci_pend_le_conn_
lookup().
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We should only accept connection parameters from identity addresses
(public or random static). Thus, we should check the address type
in hci_conn_params_add().
Additionally, since the IRK is removed during unpair, we should also
remove the connection parameters from that device.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When hdev is closed (e.g. Mgmt power off command, RFKILL or controller
is reset), the ongoing active connections are silently dropped by the
controller (no Disconnection Complete Event is sent to host). For that
reason, the devices that require HCI_AUTO_CONN_ALWAYS are not added to
hdev->pend_le_conns list and they won't auto connect.
So to fix this issue, during hdev closing, we remove all pending LE
connections. After adapter is powered on, we add a pending LE connection
for each HCI_AUTO_CONN_ALWAYS address.
This way, the auto connection mechanism works propely after a power
off and power on sequence as well as RFKILL block/unblock.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the user sends a mgmt start discovery command while the background
scanning is running, we should temporarily stop it. Once the discovery
finishes, we start the background scanning again.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch modifies hci_conn_params_add() and hci_conn_params_del() so
they also add/delete pending LE connections according to the auto_
connect option. This way, background scan is automatically triggered/
untriggered when connection parameters are added/removed.
For instance, when a new connection parameters with HCI_AUTO_CONN_ALWAYS
option is added and we are not connected to the device, we add a pending
LE connection for that device.
Likewise, when the connection parameters are updated we add or delete
a pending LE connection according to its new auto_connect option.
Finally, when the connection parameter is deleted we also delete the
pending LE connection (if any).
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduces the LE auto connection options: HCI_AUTO_CONN_
ALWAYS and HCI_AUTO_CONN_LINK_LOSS. Their working mechanism are
described as follows:
The HCI_AUTO_CONN_ALWAYS option configures the kernel to always re-
establish the connection, no matter the reason the connection was
terminated. This feature is required by some LE profiles such as
HID over GATT, Health Thermometer and Blood Pressure. These profiles
require the host autonomously connect to the device as soon as it
enters in connectable mode (start advertising) so the device is able
to delivery notifications or indications.
The BT_AUTO_CONN_LINK_LOSS option configures the kernel to re-
establish the connection in case the connection was terminated due
to a link loss. This feature is required by the majority of LE
profiles such as Proximity, Find Me, Cycling Speed and Cadence and
Time.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduces the LE auto connection infrastructure which
will be used to implement the LE auto connection options.
In summary, the auto connection mechanism works as follows: Once the
first pending LE connection is created, the background scanning is
started. When the target device is found in range, the kernel
autonomously starts the connection attempt. If connection is
established successfully, that pending LE connection is deleted and
the background is stopped.
To achieve that, this patch introduces the hci_update_background_scan()
which controls the background scanning state. This function starts or
stops the background scanning based on the hdev->pend_le_conns list. If
there is no pending LE connection, the background scanning is stopped.
Otherwise, we start the background scanning.
Then, every time a pending LE connection is added we call hci_update_
background_scan() so the background scanning is started (in case it is
not already running). Likewise, every time a pending LE connection is
deleted we call hci_update_background_scan() so the background scanning
is stopped (in case this was the last pending LE connection) or it is
started again (in case we have more pending LE connections). Finally,
we also call hci_update_background_scan() in hci_le_conn_failed() so
the background scan is restarted in case the connection establishment
fails. This way the background scanning keeps running until all pending
LE connection are established.
At this point, resolvable addresses are not support by this
infrastructure. The proper support is added in upcoming patches.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduces the hdev->pend_le_conn list which holds the
device addresses the kernel should autonomously connect. It also
introduces some helper functions to manipulate the list.
The list and helper functions will be used by the next patch which
implements the LE auto connection infrastructure.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves address type conversion (L2CAP address type to HCI
address type) to outside hci_connect_le. This way, we avoid back and
forth address type conversion in a comming patch.
So hci_connect_le() now expects 'dst_type' parameter in HCI address
type convention.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
hci_connect() is a very simple and useless wrapper of hci_connect_acl
and hci_connect_le functions. Addtionally, all places where hci_connect
is called the link type value is passed explicitly. This way, we can
safely delete hci_connect, declare hci_connect_acl and hci_connect_le
in hci_core.h and call them directly.
No functionality is changed by this patch.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes hci_create_le_conn() since it is not used anymore.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some LE controllers don't support scanning and creating a connection
at the same time. So we should always stop scanning in order to
establish the connection.
Since we may prematurely stop the discovery procedure in favor of
the connection establishment, we should also cancel hdev->le_scan_
disable delayed work and set the discovery state to DISCOVERY_STOPPED.
This change does a small improvement since it is not mandatory the
user stops scanning before connecting anymore. Moreover, this change
is required by upcoming LE auto connection mechanism in order to work
properly with controllers that don't support background scanning and
connection establishment at the same time.
In future, we might want to do a small optimization by checking if
controller is able to scan and connect at the same time. For now,
we want the simplest approach so we always stop scanning (even if
the controller is able to carry out both operations).
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the "hci_" prefix to le_conn_failed() helper and
declares it in hci_core.h so it can be reused in hci_event.c.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves stop LE scanning duplicate code to one single
place and reuses it. This will avoid more duplicate code in
upcoming patches.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that to-be-received keys are properly tracked we no-longer need the
"force" parameter to smp_distribute_keys(). It was essentially acting as
an indicator whether all keys have been received, but now it's just
redundant together with smp->remote_key_dist.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that smp->remote_key_dist is tracking the keys we're still waiting
for we can use it to simplify the logic for checking whether we're done
with key distribution or not. At the same time the reliance on the
"force" parameter of smp_distribute_keys goes away and it can completely
be removed in a subsequent patch.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To make is easier to track which keys we've received and which ones
we're still waiting for simply clear the corresponding key bits from
smp->remote_key_dist as they get received. This will allow us to
simplify the code for checking for SMP completion in subsequent patches.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Core Specification (4.1) leaves room for sending an SMP Identity
Address Information PDU with an all-zeros BD_ADDR value. This
essentially means that we would not have an Identity Address for the
device and the only means of identifying it would be the IRK value
itself.
Due to lack of any known implementations behaving like this it's best to
keep our implementation as simple as possible as far as handling such
situations is concerned. This patch updates the Identity Address
Information handler function to simply ignore the IRK received from such
a device.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the connectable setting is toggled using mgmt_set_connectable the
HCI_CONNECTABLE flag will only be set once the related HCI commands
succeed. When determining what kind of advertising to do we need to
therefore also check whether there is a pending Set Connectable command
in addition to the current flag value.
The enable_advertising function was already taking care of this for the
advertising type with the help of the get_adv_type function, but was
failing to do the same for the address type selection. This patch
converts the get_adv_type function to be more generic in that it returns
the expected connectable state and updates the enable_advertising
function to use the return value both for the advertising type as well
as the advertising address type.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To be friendly to user space and to behave well with controllers that
lack a proper internal power off procedure we should try to clean up as
much state as possible before requesting the HCI driver to power off.
This patch updates the power off procedure that's triggered by
mgmt_set_powered to clean any scan modes, stop LE scanning and
advertising and to disconnect any open connections.
The asynchronous cleanup procedure uses the HCI request framework,
however since HCI_Disconnect is only covered until its Command Status
event we need some extra tracking/waiting of disconnections. This is
done by monitoring when hci_conn_count() indicates that there are no
more connections.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Once mgmt_set_powered(off) is updated to clear the scan mode we should
not just blindly clear the HCI_ADVERTISING flag in mgmt_advertising()
but first check if there is a pending set_powered operation.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Once mgmt_set_powered(off) is updated to clear the scan mode we should
not just blindly clear the HCI_CONNECTABLE flag in mgmt_connectable()
but first check if there is a pending set_powered operation.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Once mgmt_set_powered(off) is updated to clear the scan mode we should
not just blindly clear the HCI_DISCOVERABLE flag in mgmt_discoverable()
but first check if there is a pending set_powered operation.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Once mgmt_set_powered(off) starts doing disconnections we'll need to
care about any disconnections in mgmt.c and not just those with the
MGMT_CONNECTED flag set. Therefore, move the check into mgmt.c from
hci_event.c.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We'll soon need to make decisions on toggling the HCI_ADVERTISING flag
based on pending mgmt_set_powered commands. Therefore, move the handling
from hci_event.c into mgmt.c.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The RPA expiry timer is only initialized inside mgmt.c when we receive
the first command from user space. This action also involves setting the
HCI_MGMT flag for the first time so that flag acts as a good indicator
of whether the delayed work variable can be touched or not. This patch
fixes hci_dev_do_close to first check the flag.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add a comment noting that some devices depend on the destination address being
stored in uniq.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A user space that supports the Set Privacy command is also expected to
be able to handle New IRK events. Therefore, set the HCI_RPA_RESOLVING
flag whenever the Set Privacy command is received.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The identity information in debugfs currently do not include the
current in use local RPA. Since the RPA is now stored in the
controller information, include it in the debugfs as well.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The RPA needs to be stored to know which is the current one. Otherwise
it is impossible to ensure that always the correct RPA can be programmed
into the controller when it is needed.
Current code checks if the address in the controller is a RPA, but that
can potentially lead to using a RPA that can not be resolved with the
IRK that has been distributed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When enabling non-connectable advertising, there is no need to advertise
with a public address or static address. In case LE privacy has not been
enabled a unresolvable private address will be used.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When running active scanning during LE discovery, do not reveal the own
identity to the peer devices. In case LE privacy has been enabled, then
a resolvable private address is used. If the LE privacy option is off,
then use an unresolvable private address.
The public address or static random address is never used in active
scanning anymore. This ensures that scan request are send using a
random address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When using LE Privacy it is useful to know the local identity address,
identity address type and identity resolving key. For debugging purposes
add these information to debugfs.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Now that the identity address type is always looked up for all
successful connections, the hdev->own_addr_type variable has become
completely unnecessary. Simply remove it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch ensures that conn->src_type contains the same address type as
is used for initiating the connection while the connection attempt is in
progress. Once connected this value will be overwritten with the
identity address type.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for handling the Set Privacy mgmt command,
including copying the value to hdev->irk and toggling the HCI_PRIVACY
flag.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a rpa_timeout debugfs entry which can be used to set the
RPA regeneration timeout to something else than the default 15 minutes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since we always update the random address before enabling advertising,
scanning and initiating LE connections there is no need to write the
random address add power on.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we start LE scanning we need to update the local random address if
necessary. This patch updates the code to use hci_update_random_address()
for setting the own_address_type scan parameter and updating the local
random address if necessary.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we enable advertising we need to update the local random address if
necessary. This patch takes advantage of the hci_update_random_address()
function to set the own_address_type variable and to update the local
random address if necessary.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we initiate LE connections we need to update the local random
address if necessary. This patch updates the LE connection creation
mechanism to use the new hci_update_random_address() function to set the
own_address_type parameter and to update the local random address if
necessary.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a convenience function for updating the local random
address which is needed before advertising, scanning and initiating LE
connections.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a timer for updating the local RPA periodically. The
default timeout is set to 15 minutes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We need a function in smp.c to generate Resolvable Random Addresses in
order to support privacy. The local RPA will need to be generated before
advertising, scanning or connecting and regenerated at periodic
intervals. This patch adds the necessary function for RPA generation.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The SMP Identity Address Information PDU should contain our Identity
Address. This patch updates the code to copy the correct values from the
hci_conn object.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To be consistent with the remote address info in hci_conn we want it to
also contain the local identity address information. This patch updates
the code to copy the right values in place whenever an LE connection has
been established.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch makes sure that the Privacy flag is available in the mgmt
supported settings for all LE capable controllers and in the current
settings whenever the HCI_PRIVACY flag is set.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
These functions will soon be needed by the RPA regeneration timeout so
move them higher up in mgmt.c to avoid a forward declaration.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This code adds a HCI_PRIVACY flag to track whether Privacy support is
enabled (meaning we have a local IRK) and makes sure the IRK is
distributed during SMP key distribution in case this flag is set.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch a couple of helper variables to the smp_distribute_keys
function in order to avoid long chains of dereferences and thereby help
readability.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The event opcode for New Identity Resolving Key event is missing from
supported event list. Just add it there.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We should be iterating hdev->identity_resolving_keys in the
hci_remove_irk() function instead of hdev->long_term_keys. This patch
fixes the issue.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
With the addition of Resolvable Private Address (RPA) resolution
support for Bluetooth Low Energy connections, it makes sense to
increase the minor version of the Bluetooth core module.
The module version is not used anywhere, but it gives a nice extra
hint for debugging purposes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For testing purposes it is useful to provide an option to change the
advertising channel map. So add a debugfs option to allow this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When binding RFCOMM socket with non-zero channel we're checking if
there is already any other socket which has the same channel number
assigned and then fail. This check does not consider situation where
we have another socket connected to remote device on given channel
number in which case we still should be able to bind local socket.
This patch changes __rfcomm_get_sock_by_addr() to return only sockets
in either BT_BOUND or BT_LISTEN states, also name is updated to better
describe what this function does now.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For Bluetooth controllers with LE support, track the value of the
currently configured random address. It is important to know what
the current random address is to avoid unneeded attempts to set
a new address. This will become important when introducing the
LE privacy support in the future.
In addition expose the current configured random address via
debugfs for debugging purposes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The own_address_type debugfs option does not providing enough
flexibity for interacting with the upcoming LE privacy support.
What really is needed is an option to force using the static address
compared to the public address. The new force_static_address debugfs
option does exactly that. In addition it is also only available when
the controller does actually have a public address. For single mode
LE only controllers this option will not be available.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The code itself is not descriptive on what store hint is used for
long term keys and why. So add some extensive comment here. Similar
to what has already been done for identity resolving key store hint.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The identity resolving keys should only be stored for devices using
resolvable random addresses. If the device is already using an
identity address, inform it about the new identity resolving key,
but tell userspace that this key is not persistent.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds the necessary helper function to send the New IRK mgmt
event and makes sure that the function is called at when SMP key
distribution has completed. The event is sent before the New LTK event
so user space knows which remote device to associate with the keys.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the SMP Long Term Key notification over mgmt from the
hci_add_ltk function to smp.c when both sides have completed their key
distribution. This way we are also able to update the identity address
into the mgmt_new_ltk event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As preparation to do mgmt notification in a single place at the end of
the key distribution, store the keys that need to be notified within the
SMP context.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
It's simpler (one less if-statement) to just evaluate the appropriate
value for store_hint in the mgmt_new_ltk function than to pass a boolean
parameter to the function. Furthermore, this simplifies moving the mgmt
event emission out from hci_add_ltk in subsequent patches.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The SMP code will need to postpone the mgmt event emission for the IRK
and LTKs. To avoid extra lookups at the end of the key distribution
simply return the added value from the add_ltk and add_irk functions.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The various pieces of data cached in the hci_dev structure do not need
to be allocated using GFP_ATOMIC since they are never added from
interrupt context. This patch updates these allocations to use
GFP_KERNEL instead.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During LE connection establishment the value 0x0000 is used for min/max
connection event length. So use the same value when the peripheral is
requesting an update of the the connection paramters.
For some reason the value 0x0001 got used in the connection update and
0x0000 in the connection creation. Using the same value for both just
makes sense.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For debugging purposes expose the current list of identity resolving
keys via debugfs. This file is read-only and limited to root access.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the connection attempt fails, the address information are not
provided in the HCI_LE_Connection_Complete event. So use the original
information from the connection to reconstruct the identity address.
This is important when a connection attempt has been made using the
identity address, but the cached resolvable random address has changed
in the meantime. The failure event needs to use the identity address
and not the resolvable random address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When reporting connect failed events to userspace, use the address
of the connection and not the address from the HCI event.
This change is strictly speaking not needed since BR/EDR does not
have the concept of resolvable random addresses. It is more for
making the code consistent.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the remote device has been successfully connected, report the
identity address (public address or static random address).
Currently the address from the HCI_LE_Connection_Complete event is
used. This was no problem so far, but since now known resolvable
random addresses are converted into identities, it is important to
use the identity of the connection and not the address report by
HCI event.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Pull HID update from Jiri Kosina:
- fixes for several bugs in incorrect allocations of buffers by David
Herrmann and Benjamin Tissoires.
- support for a few new device IDs by Archana Patni, Benjamin
Tissoires, Huei-Horng Yo, Reyad Attiyat and Yufeng Shen
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hyperv: make sure input buffer is big enough
HID: Bluetooth: hidp: make sure input buffers are big enough
HID: hid-sensor-hub: quirk for STM Sensor hub
HID: apple: add Apple wireless keyboard 2011 JIS model support
HID: fix buffer allocations
HID: multitouch: add FocalTech FTxxxx support
HID: microsoft: Add ID's for Surface Type/Touch Cover 2
HID: usbhid: quirk for CY-TM75 75 inch Touch Overlay
Silently dropping L2CAP data (i.e. due to remote device not obeying
negotiated MTU) is confusing and makes debugging harder.
Signed-off-by: Szymon Janc <szymon.janc@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Whenever a device uses an RPA we want to have user space identify it by
its Identity Address if we've got an IRK available for it. This patch
updates the Device Found mgmt event to contain the Identity Address if
an IRK is available for the device in question.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We need to check whether there's a matching IRK and RPA when we're
requested to connect to a remote LE device based on its Identity
Address. This patch updates the hci_connect_le function to do an extra
call to hci_find_irk_by_addr and uses the RPA if it's cached. This is
particularly important once we start exposing the Identity Address to
user space instead of the RPA in events such as Device Connected and
Device Found.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Identity Addresses are either public or static random. When looking up
addresses based on the Identity Address it doesn't make sense to go
through the IRK list if we're given a private random address. This patch
fixes (or rather improves) the hci_find_irk_by_addr function to bail out
early if given a private random address.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we initiate pairing through mgmt_pair_device the code has so far
been waiting for a successful HCI Encrypt Change event in order to
respond to the mgmt command. However, putting privacy into the play we
actually want the key distribution to be complete before replying so
that we can include the Identity Address in the mgmt response.
This patch updates the various hci_conn callbacks for LE in mgmt.c to
only respond in the case of failure, and adds a new mgmt_smp_complete
function that the SMP code will call once key distribution has been
completed.
Since the smp_chan_destroy function that's used to indicate completion
and clean up the SMP context can be called from various places,
including outside of smp.c, the easiest way to track failure vs success
is a new flag that we set once key distribution has been successfully
completed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we receive a remote identity address during SMP key distribution we
should ensure that any associated L2CAP channel instances get their
address information correspondingly updated (so that e.g. doing
getpeername on associated sockets returns the correct address).
This patch adds a new L2CAP core function l2cap_conn_update_id_addr()
which is used to iterate through all L2CAP channels associated with a
connection and update their address information.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since we want user space to see and use the LE Identity Address whenever
interfacing with the kernel it makes sense to track that instead of the
real address (the two will only be different in the case of an RPA).
This patch adds the necessary updates to when an LE connection gets
established and when receiving the Identity Address from a remote
device.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that each HCI device has its own AES crypto context we don't need
the one stored in the SMP data any more. This patch removes the variable
from struct smp_chan and updates the SMP code to use the per-hdev crypto
context.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When mgmt_unpair_device is called we should also remove any associated
IRKs. This patch adds a hci_remove_irk convenience function and ensures
that it's called when mgmt_unpair_device is called.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we're the acceptors (peripheral/slave) of an SMP procedure and
we've completed distributing our keys we should only stick around
waiting for keys from the remote side if any of the initiator
distribution bits were actually set. This patch fixes the
smp_distribute_keys function to clear the SMP context when this
situation occurs.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There is code (in mgmt.c) that depends on the hci_remove_ltk function to
fail if no match is found. This patch adds tracking of removed LTKs
(there can be up to two: one for master and another for slave) in the
hci_remove_ltk function and returns -ENOENT of no matches were found.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are many functions that never fail but still declare an integer
return value for no reason. This patch converts these functions to use a
void return value to avoid any confusion of whether they can fail or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When removing Long Term Keys we should also be checking that the given
address type (public vs random) matches. This patch updates the
hci_remove_ltk function to take an extra parameter and uses it for
address type matching.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we didn't request certain pieces of information during the key
distribution negotiation we should properly ignore those PDUs if the
peer incorrectly sends them. This includes the Encryption Information
and Master Identification PDUs if the EncKey bit was not set, and the
Identity Information and Identity Address Information PDUs if the IdKey
bit was not set.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg