[ Upstream commit 50da74e1e8b682853d1e07fc8bbe3a0774ae5e09 ]
Refer to Mediatek vendor driver RxDCOC_Calibration() function, when
performing gainfreeze calibration, we should write register 140
instead of 141. This fix can reduce the total calibration time from
6 seconds to 1 second.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/TYAP286MB0315B13B89DF57B6B27BB854BCAFA@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a11d965a218f0cd95b13fe44d0bcd8a20ce134a8 ]
When a hardware reset is triggered, all registers are reset, so all
queues are forced to stop in hardware interface. However, mac80211
will not automatically stop the queue. If we don't manually stop the
beacon queue, the queue will be deadlocked and unable to start again.
This patch fixes the issue where Apple devices cannot connect to the
AP after calling ieee80211_restart_hw().
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/TYAP286MB031530EB6D98DCE4DF20766CBCA4A@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM
Signed-off-by: Sasha Levin <sashal@kernel.org>
A mouse that uses a USB connection is called a "USB mouse" device (or
"USB mouse" for short), not a "mouse USB" device. By analogy, a WiFi
adapter that connects to the host computer via USB is a "USB wireless"
device, not a "wireless USB" device. (The latter term more properly
refers to a defunct Wireless USB specification, which described a
technology for sending USB protocol messages over an ultra wideband
radio link.)
Similarly for a WiFi adapter card that plugs into a PCIe slot: It is a
"PCIe wireless" device, not a "wireless PCIe" device.
Rephrase the text in the kernel source where the word ordering is
wrong.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/57da7c80-0e48-41b5-8427-884a02648f55@rowland.harvard.edu
In the vendor driver, the current channel power is queried from
EEPROM_TXPOWER_BG1 and EEPROM_TXPOWER_BG2. And then the mixed value
will be written into the low half-word of the TX_ALC_CFG_0 register.
The high half-word of the TX_ALC_CFG_0 is a fixed value 0x2f2f.
We can't get the accurate TX power. Based on my tests and the new
MediaTek mt76 driver source code, the real TX power is approximately
equal to channel_power + (max) rate_power. Usually max rate_power is
the gain of the OFDM 6M rate, which can be readed from the offset
EEPROM_TXPOWER_BYRATE +1.
Based on these eeprom values, this patch adds basic TX power control
for the MT7620 and limits its maximum TX power. This can avoid the
link speed decrease caused by chip overheating. rt2800_config_alc()
function has also been renamed to rt2800_config_alc_rt6352() because
it's only used by RT6352 (MT7620).
Notice:
It's still need some work to sync the max channel power to the user
interface. This part is missing from the rt2x00 driver framework. If
we set the power exceed the calibration value, it won't take effect.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/TYAP286MB03159090ED14044215E59FD6BC10A@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM
The assignment of the else and else if branches is the same, so the else
if here is redundant, so we remove it.
./drivers/net/wireless/ralink/rt2x00/rt2800lib.c:8927:9-11: WARNING:
possible condition with no effect (if == else).
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=3631
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230106022731.111243-1-jiapeng.chong@linux.alibaba.com
On some platforms, `char` is unsigned, but this driver, for the most
part, assumed it was signed. In other places, it uses `char` to mean an
unsigned number, but only in cases when the values are small. And in
still other places, `char` is used as a boolean. Put an end to this
confusion by declaring explicit types, depending on the context.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221019155541.3410813-1-Jason@zx2c4.com
mac80211 is fully switching over to the internal TX queue (iTXQ)
implementation. Update all drivers not yet providing the now mandatory
wake_tx_queue() callback.
As an side effect the netdev interfaces of all updated drivers will
switch to the noqueue qdisc.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[add staging drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of using the default value 33 (pci), set US_CYC_CNT init based
on Programming guide:
If available, set chipset bus clock with fallback to cpu clock/3.
Reported-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/3e275d259f476f597dab91a9c395015ef3fe3284.1663445157.git.daniel@makrotopia.org
Add RXIQ calibration found in mtk driver. With old openwrt builds this
gets us ~8Mbps more of RX bandwidth (test with iPA/eLNA layout).
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/033a39a697d51f6df258acea4c33608e0944fe4c.1663445157.git.daniel@makrotopia.org
Move bbp_ready and rf_ready busy wait functions up in the code so they
can more easily be used. Allow specifying register mask in rf_ready
function which is useful for calibration routines which will be added
in follow-up commits.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/3fdb9dc15e76a9f9c1948b4a3a1308a7a5677bb8.1663445157.git.daniel@makrotopia.org
Implement support for external PA connected to MT7620A.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
[pozega.tomislav@gmail.com: use chanreg and dccal helpers.]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/af2c68ff831816a86fc39b0c10911c129a1f03dc.1663445157.git.daniel@makrotopia.org
This adds a (currently missing) throughput LED trigger for the rt2x00
driver. Previously, LED triggers had to be assigned to the netdev, which
was limited to a single VAP.
Tested-by: Christoph Krapp <achterin@googlemail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/73f5ba4134e621462a26186449400cf0c1ac1730.1663445157.git.daniel@makrotopia.org
Fix incorrect RF value encoded in EEPROM on devices with Ralink Rt5592
PCIe radio (a single chip 2T2R 802.11abgn solution).
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/d7eccb2c7b8ec4cd360fa2007796abffc35abb0d.1663445157.git.daniel@makrotopia.org
Even though ieee80211_hw.queues is set to 2, the ralink rt2x00 driver
is seeing tx skbs submitted to it with the queue-id set to 2 / set to
IEEE80211_AC_BE on a rt2500 card when associating with an access-point.
This causes rt2x00queue_get_tx_queue() to return NULL and the following
error to be logged: "ieee80211 phy0: rt2x00mac_tx: Error - Attempt to
send packet over invalid queue 2", after which association with the AP
fails.
This patch works around this by mapping QID_AC_BE and QID_AC_BK
to QID_AC_VI when there are only 2 tx_queues.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908173618.155291-2-hdegoede@redhat.com
The SMPS power save mode needs to be per-link rather than being shared
for all links. As such, move it into struct ieee80211_link_sta.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the link id through to the get_beacon and return
the beacon for a specific link id.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Split the bss_info_changed method to vif_cfg_changed and
link_info_changed, with the latter getting a link ID.
Also change the 'changed' parameter to u64 already, we
know we need that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll use bss_conf for per-link configuration later, so
move out all the non-link-specific data out into a new
struct ieee80211_vif_cfg used in the vif.
Some adjustments were done with the following spatch:
@@
expression sdata;
struct ieee80211_vif *vifp;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
(
-sdata->vif.bss_conf.var
+sdata->vif.cfg.var
|
-vifp->bss_conf.var
+vifp->cfg.var
)
@bss_conf@
struct ieee80211_bss_conf *bss_conf;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
-bss_conf->var
+vif_cfg->var
(though more manual fixups were needed, e.g. replacing
"vif_cfg->" by "vif->cfg." in many files.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for the
USB core, but there are the usual "hot spots" of development activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes. It seems this driver will never
be finished given that the IP core is showing up in zillions
of new devices and each implementation decides to do something
different with it...
- uvc gadget driver updates as more devices start to use and
rely on this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYpnZGw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymQhwCeLVANsQjBcL4ys4skl+1In17y28gAn3rEZ7rQ
Yv4uP9zadUqg3Cx0vjgf
=3s5s
-----END PGP SIGNATURE-----
Merge tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for
the USB core, but there are the usual "hot spots" of development
activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes.
It seems this driver will never be finished given that the IP core
is showing up in zillions of new devices and each implementation
decides to do something different with it...
- uvc gadget driver updates as more devices start to use and rely on
this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems"
* tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits)
USB: new quirk for Dell Gen 2 devices
usb: dwc3: core: Add error log when core soft reset failed
usb: dwc3: gadget: Move null pinter check to proper place
usb: hub: Simplify error and success path in port_over_current_notify
usb: cdns3: allocate TX FIFO size according to composite EP number
usb: dwc3: Fix ep0 handling when getting reset while doing control transfer
usb: Probe EHCI, OHCI controllers asynchronously
usb: isp1760: Fix out-of-bounds array access
xhci: Don't defer primary roothub registration if there is only one roothub
USB: serial: option: add Quectel BG95 modem
USB: serial: pl2303: fix type detection for odd device
xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI
xhci: Remove quirk for over 10 year old evaluation hardware
xhci: prevent U2 link power state if Intel tier policy prevented U1
xhci: use generic command timer for stop endpoint commands.
usb: host: xhci-plat: omit shared hcd if either root hub has no ports
usb: host: xhci-plat: prepare operation w/o shared hcd
usb: host: xhci-plat: create shared hcd after having added main hcd
xhci: prepare for operation w/o shared hcd
xhci: factor out parts of xhci_gen_setup()
...
The third argument of usb_maxpacket(): in_out has been deprecated
because it could be derived from the second argument (e.g. using
usb_pipeout(pipe)).
N.B. function usb_maxpacket() was made variadic to accommodate the
transition from the old prototype with three arguments to the new one
with only two arguments (so that no renaming is needed). The variadic
argument is to be removed once all users of usb_maxpacket() get
migrated.
CC: Oliver Neukum <oliver@neukum.org>
CC: David S. Miller <davem@davemloft.net>
CC: Jakub Kicinski <kuba@kernel.org>
CC: Woojung Huh <woojung.huh@microchip.com>
CC: Felix Fietkau <nbd@nbd.name>
CC: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
CC: Ryder Lee <ryder.lee@mediatek.com>
CC: Kalle Valo <kvalo@kernel.org>
CC: Matthias Brugger <matthias.bgg@gmail.com>
CC: Stanislaw Gruszka <stf_xl@wp.pl>
CC: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20220317035514.6378-6-mailhol.vincent@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently in mac80211 each STA object is represented
using sta_info datastructure with the associated
STA specific information and drivers access ieee80211_sta
part of it.
With MLO (Multi Link Operation) support being added
in 802.11be standard, though the association is logically
with a single Multi Link capable STA, at the physical level
communication can happen via different advertised
links (uniquely identified by Channel, operating class,
BSSID) and hence the need to handle multiple link
STA parameters within a composite sta_info object
called the MLD STA. The different link STA part of
MLD STA are identified using the link address which can
be same or different as the MLD STA address and unique
link id based on the link vif.
To support extension of such a model, the sta_info
datastructure is modified to hold multiple link STA
objects with link specific params currently within
sta_info moved to this new structure. Similarly this is
done for ieee80211_sta as well which will be accessed
within mac80211 as well as by drivers, hence trivial
driver changes are expected to support this.
For current non MLO supported drivers, only one link STA
is present and link information is accessed via 'deflink'
member.
For MLO drivers, we still need to define the APIs etc. to
get the correct link ID and access the correct part of
the station info.
Currently in mac80211, all link STA info are accessed directly
via deflink. These will be updated to access via link pointers
indexed by link id with MLO support patches, with link id
being 0 for non MLO supported cases.
Except for couple of macro related changes, below spatch takes
care of updating mac80211 and driver code to access to the
link STA info via deflink.
@ieee80211_sta@
struct ieee80211_sta *s;
struct sta_info *si;
identifier var = {supp_rates, ht_cap, vht_cap, he_cap, he_6ghz_capa, eht_cap, rx_nss, bandwidth, txpwr};
@@
(
s->
- var
+ deflink.var
|
si->sta.
- var
+ deflink.var
)
@sta_info@
struct sta_info *si;
identifier var = {gtk, pcpu_rx_stats, rx_stats, rx_stats_avg, status_stats, tx_stats, cur_max_bandwidth};
@@
(
si->
- var
+ deflink.var
)
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Link: https://lore.kernel.org/r/1649086883-13246-1-git-send-email-quic_srirrama@quicinc.com
[remove MLO-drivers notes from commit message, not clear yet; run spatch]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As reported by Exuvo is possible that we have lot's of EPROTO errors
during device start i.e. firmware load. But after that device works
correctly. Hence marking device gone by few EPROTO errors done by
commit e383c70474 ("rt2x00: check number of EPROTO errors") caused
regression - Exuvo device stop working after kernel update. To fix
disable the check during device start.
Link: https://lore.kernel.org/linux-wireless/bff7d309-a816-6a75-51b6-5928ef4f7a8c@exuvo.se/
Reported-and-tested-by: Exuvo <exuvo@exuvo.se>
Fixes: e383c70474 ("rt2x00: check number of EPROTO errors")
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211111141003.GA134627@wp.pl
The device 0x043e,0x7a32 is already on the list under
CONFIG_RT2800USB_RT55XX. Since it is the sole Arcadyan entry in RT55xx,
assume the proper chip is RT55xx, not RT53xx, although this was not
confirmed by testing or 3rd party sources.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210917092108.19497-3-krzysztof.kozlowski@canonical.com
We setup hardware to insert TSF timestamp for beacon and probe response
frames. This is undesired for injected frames, which might want to
set their own timestamp values, so disable this setting for injected
frames.
Tested-by: ZeroBeat <ZeroBeat@gmx.de>
Tested-by: n0w1re <n0w1re@protonmail.ch>
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210504081220.666939-1-stf_xl@wp.pl
There are a few leading spaces before tabs and remove it by running the
following commard:
$ find . -name '*.c' | xargs sed -r -i 's/^[ ]+\t/\t/'
$ find . -name '*.h' | xargs sed -r -i 's/^[ ]+\t/\t/'
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1621407345-10625-3-git-send-email-tanghui20@huawei.com
of_get_mac_address() returns a "const void*" pointer to a MAC address.
Lately, support to fetch the MAC address by an NVMEM provider was added.
But this will only work with platform devices. It will not work with
PCI devices (e.g. of an integrated root complex) and esp. not with DSA
ports.
There is an of_* variant of the nvmem binding which works without
devices. The returned data of a nvmem_cell_read() has to be freed after
use. On the other hand the return of_get_mac_address() points to some
static data without a lifetime. The trick for now, was to allocate a
device resource managed buffer which is then returned. This will only
work if we have an actual device.
Change it, so that the caller of of_get_mac_address() has to supply a
buffer where the MAC address is written to. Unfortunately, this will
touch all drivers which use the of_get_mac_address().
Usually the code looks like:
const char *addr;
addr = of_get_mac_address(np);
if (!IS_ERR(addr))
ether_addr_copy(ndev->dev_addr, addr);
This can then be simply rewritten as:
of_get_mac_address(np, ndev->dev_addr);
Sometimes is_valid_ether_addr() is used to test the MAC address.
of_get_mac_address() already makes sure, it just returns a valid MAC
address. Thus we can just test its return code. But we have to be
careful if there are still other sources for the MAC address before the
of_get_mac_address(). In this case we have to keep the
is_valid_ether_addr() call.
The following coccinelle patch was used to convert common cases to the
new style. Afterwards, I've manually gone over the drivers and fixed the
return code variable: either used a new one or if one was already
available use that. Mansour Moufid, thanks for that coccinelle patch!
<spml>
@a@
identifier x;
expression y, z;
@@
- x = of_get_mac_address(y);
+ x = of_get_mac_address(y, z);
<...
- ether_addr_copy(z, x);
...>
@@
identifier a.x;
@@
- if (<+... x ...+>) {}
@@
identifier a.x;
@@
if (<+... x ...+>) {
...
}
- else {}
@@
identifier a.x;
expression e;
@@
- if (<+... x ...+>@e)
- {}
- else
+ if (!(e))
{...}
@@
expression x, y, z;
@@
- x = of_get_mac_address(y, z);
+ of_get_mac_address(y, z);
... when != x
</spml>
All drivers, except drivers/net/ethernet/aeroflex/greth.c, were
compile-time tested.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
MODULE_SUPPORTED_DEVICE was added in pre-git era and never was
implemented. We can safely remove it, because the kernel has grown
to have many more reliable mechanisms to determine if device is
supported or not.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
remove duplicate word 'we' in comment
change 'then' to 'than' in comment
Signed-off-by: wengjianfeng <wengjianfeng@yulong.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210204005119.18060-1-samirweng1979@163.com
First set of patches for v5.11. rtw88 getting improvements to work
better with Bluetooth and other driver also getting some new features.
mhi-ath11k-immutable branch was pulled from mhi tree to avoid
conflicts with mhi tree.
Major changes:
rtw88
* major bluetooth co-existance improvements
wilc1000
* Wi-Fi Multimedia (WMM) support
ath11k
* Fast Initial Link Setup (FILS) discovery and unsolicited broadcast
probe response support
* qcom,ath11k-calibration-variant Device Tree setting
* cold boot calibration support
* new DFS region: JP
wnc36xx
* enable connection monitoring and keepalive in firmware
ath10k
* firmware IRAM recovery feature
mhi
* merge mhi-ath11k-immutable branch to make MHI API change go smoothly
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfyTQyAAoJEG4XJFUm622bCdcIAIyVnqdW7pnoDmWIyQmAEnD9
vGARkzghPHXnufpOzohyDdxT12X9klhrxSVIgzEgH1/pl3i1PpnF6KXyGFCC44Lw
wrLXhQygPzmIW1IZtJJE3G72WExXoRjWx6LD1I7C7oEIduqFixXADmK2tKzFp795
Jxum+sOeT6+Dk1OvO/fIroBHX73mRE9zAuiTIMpt2G1j8uXs9QVfcTbTrUshLASN
0sX9J6JutltBuM4G7+bFpVzKnLnlQ7ebUaF6nvTCQsgHWZwkS7yAubSWX9sFohbR
UXgQHNE83s/esOg7nBxAfqTKP8mbxsobmxZtxE5GR5vFY5FJDxqP9Zc2KzPp39w=
=CbX/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-12-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.11
First set of patches for v5.11. rtw88 getting improvements to work
better with Bluetooth and other driver also getting some new features.
mhi-ath11k-immutable branch was pulled from mhi tree to avoid
conflicts with mhi tree.
Major changes:
rtw88
* major bluetooth co-existance improvements
wilc1000
* Wi-Fi Multimedia (WMM) support
ath11k
* Fast Initial Link Setup (FILS) discovery and unsolicited broadcast
probe response support
* qcom,ath11k-calibration-variant Device Tree setting
* cold boot calibration support
* new DFS region: JP
wnc36xx
* enable connection monitoring and keepalive in firmware
ath10k
* firmware IRAM recovery feature
mhi
* merge mhi-ath11k-immutable branch to make MHI API change go smoothly
* tag 'wireless-drivers-next-2020-12-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (180 commits)
wl1251: remove trailing semicolon in macro definition
airo: remove trailing semicolon in macro definition
wilc1000: added queue support for WMM
wilc1000: call complete() for failure in wilc_wlan_txq_add_cfg_pkt()
wilc1000: free resource in wilc_wlan_txq_add_mgmt_pkt() for failure path
wilc1000: free resource in wilc_wlan_txq_add_net_pkt() for failure path
wilc1000: added 'ndo_set_mac_address' callback support
brcmfmac: expose firmware config files through modinfo
wlcore: Switch to using the new API kobj_to_dev()
rtw88: coex: add feature to enhance HID coexistence performance
rtw88: coex: upgrade coexistence A2DP mechanism
rtw88: coex: add action for coexistence in hardware initial
rtw88: coex: add function to avoid cck lock
rtw88: coex: change the coexistence mechanism for WLAN connected
rtw88: coex: change the coexistence mechanism for HID
rtw88: coex: update AFH information while in free-run mode
rtw88: coex: update the mechanism for A2DP + PAN
rtw88: coex: add debug message
rtw88: coex: run coexistence when WLAN entering/leaving LPS
Revert "rtl8xxxu: Add Buffalo WI-U3-866D to list of supported devices"
...
====================
Link: https://lore.kernel.org/r/20201203185732.9CFA5C433ED@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
rt2800 only gives you survey for current channel.
Survey-based ACS algorithms are failing to perform their job when working
with rt2800.
Make rt2800 save survey for every channel visited and be able to give away
that information.
There is a bug registered https://dev.archive.openwrt.org/ticket/19081 and
this patch solves the issue.
Signed-off-by: Markov Mikhail <markov.mikhail@itmh.ru>
sgruszka: remove unused variable
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201104142524.94375-1-stf_xl@wp.pl
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817090637.26887-15-allen.cryptic@gmail.com
Shiji Yang